The qapi visitor contract allows us to visit a virtual structure,
where we don't have any corresponding qapi struct. Most such uses
pass NULL for @obj; but these two callers were passing a dummy
pointer, which then gets allocated to heap memory but then
immediately freed without use. Clean this up to suppress unwanted
allocation, like we do elsewhere.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-7-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-16-git-send-email-peter.maydell@linaro.org
When processing 'sendkey' command, hmp_sendkey routine null
terminates the 'keyname_buf' array. This results in an OOB
write issue, if 'keyname_len' was to fall outside of
'keyname_buf' array.
Since the keyname's length is known the keyname_buf can be
removed altogether by adding a length parameter to
index_from_key() and using it for the error output as well.
Reported-by: Ling Liu <liuling-it@360.cn>
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Message-Id: <20160113080958.GA18934@olga>
[Comparison with "<" dumbed down, test for junk after strtoul()
tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1450452927-8346-25-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Both error_report_err() and monitor_printf() print to the same
destination when monitor_printf() is used correctly, i.e. within an
HMP monitor. Elsewhere, monitor_printf() does nothing, while
error_report_err() reports to stderr.
Most changed functions are HMP command handlers. These should only
run within an HMP monitor. The one exception is bdrv_password_cb(),
which should also only run within an HMP monitor.
Four command handlers prefix the error message with the command name:
balloon, migrate_set_capability, migrate_set_parameter, migrate.
Pointless, drop.
Unlike monitor_printf(), error_report_err() uses the error whole
instead of just its message obtained with error_get_pretty(). This
avoids suppressing its hint (see commit 50b7b00). Example:
(qemu) device_add ivshmem,id=666
Parameter 'id' expects an identifier
Identifiers consist of letters, digits, '-', '.', '_', starting with a letter.
Try "help device_add" for more information
The "Identifiers consist of..." line is new with this patch.
Coccinelle semantic patch:
@@
expression M, E;
@@
- monitor_printf(M, "%s\n", error_get_pretty(E));
- error_free(E);
+ error_report_err(E);
@r1@
expression M, E;
format F;
position p;
@@
- monitor_printf(M, "...%@F@\n", error_get_pretty(E));@p
- error_free(E);
+ error_report_err(E);
@script:python@
p << r1.p;
@@
print "%s:%s:%s: prefix dropped" % (p[0].file, p[0].line, p[0].column)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1450452927-8346-4-git-send-email-armbru@redhat.com>
The CpuInfo struct is used only by the 'query-cpus' output
command, so we are free to modify it by adding fields (clients
are already supposed to ignore unknown output fields), or by
changing optional members to mandatory, while still keeping
QMP wire compatibility with older versions of qemu.
When qapi type CpuInfo was originally created for 0.14, we had
no notion of a flat union, and instead just listed a bunch of
optional fields with documentation about the mutually-exclusive
choice of which instruction pointer field(s) would be provided
for a given architecture. But now that we have flat unions and
introspection, it is better to segregate off which fields will
be provided according to the actual architecture. With this in
place, we no longer need the fields to be optional, because the
choice of the new 'arch' discriminator serves that role.
This has an additional benefit: the old all-in-one struct was
the only place in the code base that had a case-sensitive
naming of members 'pc' vs. 'PC'. Separating these spellings
into different branches of the flat union will allow us to add
restrictions against future case-insensitive collisions, since
that is generally a poor interface practice.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1447836791-369-25-git-send-email-eblake@redhat.com>
[Spelling of CPUInfo{SPARC,PPC,MIPS} fixed]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we guarantee the user doesn't have any enum values
beginning with a single underscore, we can use that for our
own purposes. Renaming ENUM_MAX to ENUM__MAX makes it obvious
that the sentinel is generated.
This patch was mostly generated by applying a temporary patch:
|diff --git a/scripts/qapi.py b/scripts/qapi.py
|index e6d014b..b862ec9 100644
|--- a/scripts/qapi.py
|+++ b/scripts/qapi.py
|@@ -1570,6 +1570,7 @@ const char *const %(c_name)s_lookup[] = {
| max_index = c_enum_const(name, 'MAX', prefix)
| ret += mcgen('''
| [%(max_index)s] = NULL,
|+// %(max_index)s
| };
| ''',
| max_index=max_index)
then running:
$ cat qapi-{types,event}.c tests/test-qapi-types.c |
sed -n 's,^// \(.*\)MAX,s|\1MAX|\1_MAX|g,p' > list
$ git grep -l _MAX | xargs sed -i -f list
The only things not generated are the changes in scripts/qapi.py.
Rejecting enum members named 'MAX' is now useless, and will be dropped
in the next patch.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1447836791-369-23-git-send-email-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
[Rebased to current master, commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This patch adds the new field 'idle_time_ns' to the BlockDeviceStats
structure, indicating the time that has passed since the previous I/O
operation.
It also adds the block_acct_idle_time_ns() call, to ensure that all
references to the clock type used for accounting are in the same
place. This will later allow us to use a different clock for iotests.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 7d8cfcf931453e1a2443e6626e8c1edc347c7c8a.1446044837.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Expose the new read-only-mode option of 'blockdev-change-medium' for the
'change' HMP command.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an option to qmp_blockdev_change_medium() which allows changing the
read-only status of the block device whose medium is changed.
Some drives do not have a inherently fixed read-only status; for
instance, floppy disks can be set read-only or writable independently of
the drive. Some users may find it useful to be able to therefore change
the read-only status of a block device when changing the medium.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use separate code paths for the two overloaded functions of the 'change'
HMP command, and invoke the 'blockdev-change-medium' QMP command if used
on a block device (by calling qmp_blockdev_change_medium()).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Once postcopy is enabled (with migrate_set_capability), the migration
will still start on precopy mode. To cause a transition into postcopy
the:
migrate_start_postcopy
command must be issued. Postcopy will start sometime after this
(when it's next checked in the migration loop).
Issuing the command before migration has started will error,
and issuing after it has finished is ignored.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for TPM-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-22-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for memory-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-21-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for input-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-20-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Rather than storing a base class as a pointer to a box, just
store the fields of that base class in the same order, so that
a child struct can be directly cast to its parent. This gives
less malloc overhead, less pointer dereferencing, and even less
generated code. Compare to the earlier commit 1e6c1616a "qapi:
Generate a nicer struct for flat unions" (although that patch
had fewer places to change, as less of qemu was directly using
qapi structs for flat unions). It also allows us to turn on
automatic type-safe wrappers for upcasting to the base class
of a struct.
Changes to the generated code look like this in qapi-types.h:
| struct SpiceChannel {
|- SpiceBasicInfo *base;
|+ /* Members inherited from SpiceBasicInfo: */
|+ char *host;
|+ char *port;
|+ NetworkAddressFamily family;
|+ /* Own members: */
| int64_t connection_id;
as well as additional upcast functions like qapi_SpiceChannel_base().
Meanwhile, changes to qapi-visit.c look like:
| static void visit_type_SpiceChannel_fields(Visitor *v, SpiceChannel **obj, Error **errp)
| {
| Error *err = NULL;
|
|- visit_type_implicit_SpiceBasicInfo(v, &(*obj)->base, &err);
|+ visit_type_SpiceBasicInfo_fields(v, (SpiceBasicInfo **)obj, &err);
| if (err) {
(the cast is necessary, since our upcast wrappers only deal with a
single pointer, not pointer-to-pointer); plus the wholesale
elimination of some now-unused visit_type_implicit_FOO() functions.
Without boxing, the corner case of one empty struct having
another empty struct as its base type now requires inserting a
dummy member (previously, the 'Base *base' member sufficed).
And now that we no longer consume a 'base' member in the generated
C struct, we can delete the former negative struct-base-clash-base
test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-11-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Report throttle percentage in info migrate and query-migrate responses when
cpu throttling is active.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Add migration parameters to allow the user to adjust the parameters
that control cpu throttling when auto-converge is in effect. The added
parameters are as follows:
x-cpu-throttle-initial : Initial percantage of time guest cpus are throttled
when migration auto-converge is activated.
x-cpu-throttle-increment: throttle percantage increase each time
auto-converge detects that migration is not making progress.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Make "info iothreads" available on the HMP monitor.
For example, the results are as follows when executing qemu
command with "-object iothread,id=iothread-1 -object
iothread,id=iothread-2".
(qemu) info iothreads
iothread-1: thread_id=123
iothread-2: thread_id=456
Signed-off-by: Ting Wang <kathy.wangting@huawei.com>
Message-Id: <1435306033-58372-1-git-send-email-kathy.wangting@huawei.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Amos Jianjun Kong <kongjianjun@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
If specified as "true", it allows discarding on target sectors where source is
not allocated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
The traditional QMP command handler interface
int qmp_FOO(Monitor *mon, const QDict *params, QObject **ret_data);
doesn't provide for returning an Error object. Instead, the handler
is expected to stash it in the monitor with qerror_report().
When we rebased QMP on top of QAPI, we didn't change this interface.
Instead, commit 776574d introduced "middle mode" as a temporary aid
for converting existing QMP commands to QAPI one by one. More than
three years later, we're still using it.
Middle mode has two effects:
* Instead of the native input marshallers
static void qmp_marshal_input_FOO(QDict *, QObject **, Error **)
it generates input marshallers conforming to the traditional QMP
command handler interface.
* It suppresses generation of code to register them with
qmp_register_command()
This permits giving them internal linkage.
As long as we need qmp-commands.hx, we can't use the registry behind
qmp_register_command(), so the latter has to stay for now.
The former has to go to get rid of qerror_report(). Changing all QMP
commands to fit the QAPI mold in one go was impractical back when we
started, but by now there are just a few stragglers left:
do_qmp_capabilities(), qmp_qom_set(), qmp_qom_get(), qmp_object_add(),
qmp_netdev_add(), do_device_add().
Switch middle mode to generate native input marshallers, and adapt the
stragglers. Simplifies both the monitor code and the stragglers.
Rename do_qmp_capabilities() to qmp_capabilities(), and
do_device_add() to qmp_device_add, because that's how QMP command
handlers are named today.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Error classes other than ERROR_CLASS_GENERIC_ERROR should not be used
in new code. Hiding them in QERR_ macros makes new uses hard to spot.
Fortunately, there's just one such macro left. Eliminate it with this
coccinelle semantic patch:
@@
expression EP, E;
@@
-error_set(EP, QERR_DEVICE_NOT_FOUND, E)
+error_set(EP, ERROR_CLASS_DEVICE_NOT_FOUND, "Device '%s' not found", E)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
qerror_report_err() is a transitional interface to help with
converting existing monitor commands to QMP. It should not be used
elsewhere.
The only remaining user in qemu-option.c is qemu_opts_parse(). Is it
used in QMP context? If not, we can simply replace
qerror_report_err() by error_report_err().
The uses in qemu-img.c, qemu-io.c, qemu-nbd.c and under tests/ are
clearly not in QMP context.
The uses in vl.c aren't either, because the only QMP command handlers
there are qmp_query_status() and qmp_query_machines(), and they don't
call it.
Remaining uses:
* drive_def(): Command line -drive and such, HMP drive_add and pci_add
* hmp_chardev_add(): HMP chardev-add
* monitor_parse_command(): HMP core
* tmp_config_parse(): Command line -tpmdev
* net_host_device_add(): HMP host_net_add
* net_client_parse(): Command line -net and -netdev
* qemu_global_option(): Command line -global
* vnc_parse_func(): Command line -display, -vnc, default display, HMP
change, QMP change. Bummer.
* qemu_pci_hot_add_nic(): HMP pci_add
* usb_net_init(): Command line -usbdevice, HMP usb_add
Propagate errors through qemu_opts_parse(). Create a convenience
function qemu_opts_parse_noisily() that passes errors to
error_report_err(). Switch all non-QMP users outside tests to it.
That leaves vnc_parse_func(). Propagate errors through it. Since I'm
touching it anyway, rename it to vnc_parse().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Now that qbool is fixed, let's fix getting and setting a bool
value to a qdict member to also use C99 bool rather than int.
I audited all callers to ensure that the changed return type
will not cause any changed semantics.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJVevNrAAoJEJykq7OBq3PIn3wH/iTkoxK+8c6vHY4gAyW/3Vel
JAWyDULliLg/mJiyDyz+9hbyb3FmDsQ7Gve5laFCqSES8IChe/fAoR2dXAapHbJm
VroBii+C4MIakAjB1eSGVTMeJVgyq0SxCbEgo6MSgCNRg8pH/ne4kGMn0elsyMQm
VrxqsoW1qda0gLbybu7uRKmdZlb5Eklk0zQmBlzd25j3xgMXmo7ZcXW0d7dCi/xd
ot01aPNHWKy2FyYsI+N1SMagCedjn0FFCHMMc08W34olUOAschV+Croxi6gupbTl
RdlYNnB6BBYLgT7mxYuKKd20r4Q8Si3E5YjIsYaXIskbCOxDuryKboyheMXWqdA=
=mx5x
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Fri Jun 12 15:57:47 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
qemu-iotests: expand test 093 to support group throttling
throttle: Update throttle infrastructure copyright
throttle: add the name of the ThrottleGroup to BlockDeviceInfo
throttle: acquire the ThrottleGroup lock in bdrv_swap()
throttle: Add throttle group support
throttle: Add throttle group infrastructure tests
throttle: Add throttle group infrastructure
throttle: Extract timers from ThrottleState into a separate structure
raw-posix: Fix .bdrv_co_get_block_status() for unaligned image size
Revert "iothread: release iothread around aio_poll"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The throttle group support use a cooperative round robin scheduling
algorithm.
The principles of the algorithm are simple:
- Each BDS of the group is used as a token in a circular way.
- The active BDS computes if a wait must be done and arms the right
timer.
- If a wait must be done the token timer will be armed so the token
will become the next active BDS.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: f0082a86f3ac01c46170f7eafe2101a92e8fde39.1433779731.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For device_add, that's easy: just wrap the obvious hmp_device_add()
around do_device_add().
monitor_user_noop() is now unused, drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Add the hmp interface to tune and query the parameters used in
live migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
A future patch will be using a 'name':{dictionary} entry in the
QAPI schema to specify a default value for an optional argument
(see previous commit message for more details why); but existing
use of inline nested structs conflicts with that goal. This patch
fixes one of only two commands relying on nested types, by
breaking the nesting into an explicit type; it means that the
type is now boxed instead of unboxed in C code, but the QMP wire
format is unaffected by this change.
Prefer the safer g_new0() while making the conversion, and reduce
some long lines.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
A future patch will be using a 'name':{dictionary} entry in the
QAPI schema to specify a default value for an optional argument
(see previous commit message for more details why); but existing
use of inline nested structs conflicts with that goal. This patch
fixes one of only two commands relying on nested types, by
breaking the nesting into an explicit type; it means that the
type is now boxed instead of unboxed in C code, but the QMP wire
format is unaffected by this change.
Prefer the safer g_new0() while making the conversion.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
For "dirty-bitmap" sync mode, the block job will iterate through the
given dirty bitmap to decide if a sector needs backup (backup all the
dirty clusters and skip clean ones), just as allocation conditions of
"top" sync mode.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-11-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The image field in BlockDeviceInfo should never be null, however
bdrv_block_device_info() is not filling it in.
This makes the 'info block -n -v' command crash QEMU.
The proper solution is probably to move the relevant code from
bdrv_query_info() to bdrv_block_device_info(), but since we're too
close to the release for that this simpler workaround solves the
crash.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 1429274688-8115-1-git-send-email-berto@igalia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=baFB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20150317' into staging
migration/next for 20150317
# gpg: Signature made Tue Mar 17 14:21:14 2015 GMT using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20150317:
migration: Expose 'cancelling' status to user
migration: Convert 'status' of MigrationInfo to use an enum type
hmp: Rename 'MigrationStatus' to 'HMPMigrationStatus'
migration: Rename abbreviated macro MIG_STATE_* to MIGRATION_STATUS_*
migration: Remove unused functions
arch_init: Count the total number of pages by using helper function
migrate_incoming: Cleanup/clarify error messages
Warn against the use of the string as uri parameter to migrate-incoming
migrate_incoming: use hmp_handle_error
migration: Fix remaining 32 bit compiler errors
migration: Fix some 32 bit compiler errors
migration/rdma: clean up qemu_rdma_dest_init a bit
migration: Avoid qerror_report_err() outside QMP command handlers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The original 'status' is an open-coded 'str' type, convert it to use an
enum type.
This conversion is backwards compatible, better documented and
more convenient for future extensibility.
In addition, Fix a typo for qapi-schema.json (just remove the typo) :
s/'completed'. 'comppleted' (since 1.2)/'completed' (since 1.2)
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We will use the typename 'MigrationStatus' for publicly exported typename,
So here we rename the internal-only 'MigrationStatus' to
'HMPMigrationStatus'.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Re-implemented based on qmp_qom_set() to facilitate argument parsing.
Warn about ambiguous path arguments.
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Implement it as a wrapper for QMP qom-list, but mimic the behavior of
scripts/qmp/qom-list in making the path argument optional and listing
the root if absent, to hint users what kind of path to pass.
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add migrate_incoming/migrate-incoming to start an incoming
migration.
Once a qemu has been started with
-incoming defer
the migration can be started by issuing:
migrate_incoming uri
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Obvious suggestion for the next spice-protocol
release: Add some way to #ifdef new stuff.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Cole Robinson <crobinso@redhat.com>
* remotes/qmp-unstable/queue/qmp:
qapi-types: add C99 index names to arrays
monitor: Fix missing err = NULL in client_migrate_info()
balloon: Fix typo
hmp: Fix warning from smatch (wrong argument in function call)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix this warning:
hmp.c:414:38: warning: Using plain integer as NULL pointer
qmp_query_block expects a pointer argument, so passing false is wrong.
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Some are called do_COMMAND() (old ones, usually), some hmp_COMMAND(),
and sometimes COMMAND pointlessly differs in spelling.
Normalize to hmp_COMMAND(), where COMMAND is exactly the command name
with '-' replaced by '_'.
Exceptions:
* do_device_add() and client_migrate_info() *not* renamed to
hmp_device_add(), hmp_client_migrate_info(), because they're also
QMP handlers. They still need to be converted to QAPI.
* do_memory_dump(), do_physical_memory_dump(), do_ioport_read(),
do_ioport_write() renamed do hmp_* instead of hmp_x(), hmp_xp(),
hmp_i(), hmp_o(), because those names are too cryptic for my taste.
* do_info_help() renamed to hmp_info_help() instead of hmp_info(),
because it only covers help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
qemu-io should behave like a guest, therefore it should use BlockBackend
to access the block layer.
There are a couple of places where that is infeasible: First, the
bdrv_debug_* functions could theoretically be mirrored in the
BlockBackend, but since these are functions internal to the block layer,
they should not be visible externally (qemu-io as a test tool is exempt
from this).
Second, bdrv_get_info() and bdrv_get_specific_info() work on a single
BDS alone, therefore they should stay BDS-specific.
Third, bdrv_is_allocated() mainly works on a single BDS as well. Some
data may be passed through from the BDS's file (if sectors which are
apparently allocated in the file are not really allocated there but just
zero).
[Fixed conflicts around block_acct_start() usage from Fam Zheng's
"qemu-io: Account IO by aio_read and aio_write" commit. Use
BlockBackend and blk_get_stats() instead of BlockDriverState.
--Stefan]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1423162705-32065-14-git-send-email-mreitz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's dead code when CONFIG_SPICE is off. If it wasn't, it would crash
dereferencing the null pointer returned by the qmp_query_spice()
dummy in qmp.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
The optional parameter specifying a block device allows now to use a
node-name instead of a drive name (and therefore to inspect any node in
the graph). The new -n options allows listing all named nodes instead of
BlockBackends.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows printing infos of BlockDriverStates that aren't at the root
of the graph (and logically implementing a BlockBackend).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This bool option will allow query all the node names. It iterates all
the BDSes that are assigned a name, also in this case don't query up the
backing chain.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
the memdev_list in hmp_info_memdev() is never freed.
so we use existent method qapi_free_MemdevList() to free it.
and also we can use qapi_free_MemdevList() to replace list loops
to clean up the memdev list in error path.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
string_output_get_string() uses g_string_free(str, false) to
transfer the 'str' pointer to callers and never free it.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On some image chains, QEMU may not always be able to resolve the
filenames properly, when updating the backing file of an image
after a block job.
For instance, certain relative pathnames may fail, or drives may
have been specified originally by file descriptor (e.g. /dev/fd/???),
or a relative protocol pathname may have been used.
In these instances, QEMU may lack the information to be able to make
the correct choice, but the user or management layer most likely does
have that knowledge.
With this extension to the block-stream api, the user is able to change
the backing file of the active layer as part of the block-stream
operation.
This allows the change to be 'safe', in the sense that if the attempt
to write the active image metadata fails, then the block-stream
operation returns failure, without disrupting the guest.
If a backing file string is not specified in the command, the backing
file string to use is determined in the same manner as it was
previously.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
drive-mirror will bdrv_swap the new BDS named node-name with the one
pointed by replaces when the mirroring is finished.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This new argument can be used to specify the node-name of the new mirrored BDS.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to let event defines use existing types later, instead of
redefine new ones, some old type defines for spice and vnc are changed,
and BlockErrorAction is moved from block.h to qapi schema. Note that
BlockErrorAction is not merged with BlockdevOnError.
At this point, VncInfo is not made a child of VncBasicInfo, because
VncBasicInfo has mandatory fields where VncInfo makes them optional.
Signed-off-by: Wenchao Xia <wenchaoqemu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
fixup documentation comments and HMP message/help text
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is the hmp counterpart of qmp query-memdev.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MST: fix build on 32 bit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LnQj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches
# gpg: Signature made Mon 19 May 2014 15:21:14 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (22 commits)
block: optimize zero writes with bdrv_write_zeroes
blockdev: add a function to parse enum ids from strings
util: add qemu_iovec_is_zero
qcow1: Stricter backing file length check
qcow1: Validate image size (CVE-2014-0223)
qcow1: Validate L2 table size (CVE-2014-0222)
qcow1: Check maximum cluster size
qcow1: Make padding in the header explicit
curl: Add usage documentation
curl: Add sslverify option
curl: Remove broken parsing of options from url
curl: Fix build when curl_multi_socket_action isn't available
qemu-iotests: Fix blkdebug in VM drive in 030
qemu-iotests: Fix core dump suppression in test 039
iotests: Add test for the JSON protocol
block: Allow JSON filenames
check-qdict: Add test for qdict_join()
qdict: Add qdict_join()
block: add test for vhdx image created by Disk2VHD
block: vhdx - account for identical header sections
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
this patch tries to optimize zero write requests
by automatically using bdrv_write_zeroes if it is
supported by the format.
This significantly speeds up file system initialization and
should speed zero write test used to test backend storage
performance.
I ran the following 2 tests on my internal SSD with a
50G QCOW2 container and on an attached iSCSI storage.
a) mkfs.ext4 -E lazy_itable_init=0,lazy_journal_init=0 /dev/vdX
QCOW2 [off] [on] [unmap]
-----
runtime: 14secs 1.1secs 1.1secs
filesize: 937M 18M 18M
iSCSI [off] [on] [unmap]
----
runtime: 9.3s 0.9s 0.9s
b) dd if=/dev/zero of=/dev/vdX bs=1M oflag=direct
QCOW2 [off] [on] [unmap]
-----
runtime: 246secs 18secs 18secs
filesize: 51G 192K 192K
throughput: 203M/s 2.3G/s 2.3G/s
iSCSI* [off] [on] [unmap]
----
runtime: 8mins 45secs 33secs
throughput: 106M/s 1.2G/s 1.6G/s
allocated: 100% 100% 0%
* The storage was connected via an 1Gbit interface.
It seems to internally handle writing zeroes
via WRITESAME16 very fast.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When visit_start_struct() succeeds, visit_end_struct() must be called.
hmp_object_add() doesn't when a member visit fails. As far as I can
tell, the opts visitor copes okay with the misuse. Fix it anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Null errp argument makes no sense. Assert it's not null, to make this
explicit, and guard against misuse. All current callers pass non-null
errp.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
expose the count that logs the times of updating the dirty bitmap to
end user.
Signed-off-by: ChenLiang <chenliang88@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Dumping guest memory is available to specify the dump format now. This patch
adds options '-z|-l|-s' to HMP command dump-guest-memory to specify dumping in
kdump-compression format, with zlib/lzo/snappy compression. And without these
options ELF format will be used.
The discussion about this feature is here:
http://lists.nongnu.org/archive/html/qemu-devel/2014-03/msg04235.html
Signed-off-by: Qiao Nuohan <qiaonuohan@cn.fujitsu.com>
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> (on s390x/kvm)
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Make monitor command 'dump-guest-memory' be able to dump in kdump-compressed
format. The command's usage:
dump [-p] protocol [begin] [length] [format]
'format' is used to specified the format of vmcore and can be:
1. 'elf': ELF format, without compression
2. 'kdump-zlib': kdump-compressed format, with zlib-compressed
3. 'kdump-lzo': kdump-compressed format, with lzo-compressed
4. 'kdump-snappy': kdump-compressed format, with snappy-compressed
Without 'format' being set, it is same as 'elf'. And if non-elf format is
specified, paging and filter is not allowed.
Note:
1. The kdump-compressed format is readable only with the crash utility and
makedumpfile, and it can be smaller than the ELF format because of the
compression support.
2. The kdump-compressed format is the 6th edition.
Signed-off-by: Qiao Nuohan <qiaonuohan@cn.fujitsu.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
error_is_set(&var) is the same as var != NULL, but it takes
whole-program analysis to figure that out. Unnecessarily hard for
optimizers, static checkers, and human readers. Dumb it down to
obvious.
Gets rid of several dozen Coverity false positives.
Note that the obvious form is already used in many places.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This patch fixes a timing issue that migrate command (without -d) does not
block in some cases.
The original version of hmp.c:hmp_migrate_status_cb checks if the
migration status is 'active' or not to detect the completion of a migration.
However, if this function is executed when the migration status is stil
'setup' (the status before 'active'), migration command returns
immediately even if the user does not specify -d option.
Signed-off-by: Soramichi Akiyama <akiyama@nii.ac.jp>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
There was two candidate ways to implement named node manipulation:
1)
{ 'command': 'block_passwd', 'data': {'*device': 'str',
'*node-name': 'str', 'password': 'str'}
}
2)
{ 'command': 'block_passwd', 'data': {'device': 'str',
'*device-is-node': 'bool',
'password': 'str'} }
Luiz proposed 1 and says 2 was an abuse of the QMP interface and proposed to
rewrite the QMP block interface for 2.0.
Luiz does not like in 1 the fact that 2 fields are optional but one of them must
be specified leading to an abuse of the QMP semantic.
Kevin argumented that 2 what a clear abuse of the device field and would not be
practical when reading fast some log file because the user would read "device"
and think that a device is manipulated when it's in fact a node name.
Documentation of 1 make it pretty clear what to do for the user.
Kevin argued that all bs are node including devices ones so 2 does not make
sense.
Kevin also argued that rewriting the QMP block interface would not make disapear
the current one.
Kevin pushed the argument that making the QAPI generator compatible with the
semantic of the operation would need a rewrite that no one has done yet.
A vote has been done on the list to elect the version to use and 1 won.
For reference the complete thread is:
"[Qemu-devel] [PATCH V4 4/7] qmp: Allow to change password on names block driver
states."
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the readline.c functionality reusable. Instead of calling
monitor_printf() and monitor_flush() directly, invoke function pointers
provided by the user.
This way readline.c does not know about Monitor and other users will be
able to make use of readline.c.
Note that there is already an "opaque" argument to the ReadLineFunc
callback. Consistently call it "readline_opaque" from now on to
distinguish from the ReadLinePrintfFunc/ReadLineFlushFunc "opaque"
argument.
I also dropped the printf macro trickery since it's now highly unlikely
that anyone modifying readline.c would call printf(3) directly. We no
longer need this protection.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add two commands that are the monitor counterparts of -object. The commands
have the same Visitor-based implementation, but use different kinds of
visitors so that the HMP command has a DWIM string-based syntax, while
the QMP variant accepts a stricter JSON-based properties dictionary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
These two commands invoke the "unparent" method of Object.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Add HMP cpu-add wrapper to allow cpu hot plugging via monitor.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Commit 3e9fab690d ("block: Add support for
throttling burst max in QMP and the command line.") introduced bogus
"[not inserted]" output, possibly due to a merge failure. Remove this
artifact.
Output of 'info block'
scsi0-hd0: /images/f18-ppc64.qcow2 (qcow2)
[not inserted]
scsi0-cd2: [not inserted]
Removable device: not locked, tray closed
floppy0: [not inserted]
Removable device: not locked, tray closed
sd0: [not inserted]
Removable device: not locked, tray closed
There will be no additional lines between scsi0-hd0 and
scsi0-cd2.
At the same time, scsi0-hd0 already inserted, but still has
'[not inserted]' flag. This line should be removed.
This patch is to solve this.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is hard to make both id and name optional in hmp console as qmp
interface, so this interface require user to specify name.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
# By Tomoki Sekiyama (10) and Paul Burton (1)
# Via Michael Roth
* mdroth/qga-pull-2013-9-9:
QMP/qemu-ga-client: Make timeout longer for guest-fsfreeze-freeze command
qemu-ga: Install Windows VSS provider on `qemu-ga -s install'
qemu-ga: Call Windows VSS requester in fsfreeze command handler
qemu-ga: Add Windows VSS provider and requester as DLL
error: Add error_set_win32 and error_setg_win32
qemu-ga: Add configure options to specify path to Windows/VSS SDK
Add a script to extract VSS SDK headers on POSIX system
checkpatch.pl: Check .cpp files
Add c++ keywords to QAPI helper script
configure: Support configuring C++ compiler
mips_malta: support up to 2GiB RAM
Message-id: 1378755701-2051-1-git-send-email-mdroth@linux.vnet.ibm.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Add c++ keywords to avoid errors in compiling with c++ compiler.
This also renames class member of PciDeviceInfo to q_class.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This feature can be used in case where users are avoiding the iops limit by
doing jumbo I/Os hammering the storage backend.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The max parameter of the leaky bucket throttling algorithm can be used to
allow the guest to do bursts.
The max value is a pool of I/O that the guest can use without being throttled
at all. Throttling is triggered once this pool is empty.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Using the previous patches, we're now able to timestamp the SETUP
state. Once we have this time, let the user know about it in the
schema.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Make "drive_backup" available on the HMP monitor:
drive_backup [-n] [-f] device target [format]
The -n flag requests QEMU to reuse the image found in new-image-file,
instead of recreating it from scratch.
The -f flag requests QEMU to copy the whole disk, so that the result
does not need a backing file. Note that this flag *must* currently be
passed since the other sync modes ('none' and 'top') have not been
implemented yet. Requiring it ensures that "drive_backup" behaves like
"drive_mirror".
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
HMP is meant for humans and you should notice it.
This changes the output format to use a bit more space to display the
information more readable and leaves out irrelevant information (e.g.
mention only that an image is encrypted, but not when it's not; display
I/O limits only if throttling is in effect; ...)
Before:
(qemu) info block
ide0-hd0: removable=0 io-status=ok file=/tmp/overlay.qcow2
backing_file=/tmp/backing.img backing_file_depth=1 ro=0 drv=qcow2
encrypted=1 bps=0 bps_rd=0 bps_wr=0 iops=1024 iops_rd=0 iops_wr=0
ide1-cd0: removable=1 locked=0 tray-open=0 io-status=ok
file=/home/kwolf/images/iso/Fedora-18-x86_64-Live-Desktop.iso ro=1
drv=raw encrypted=0 bps=0 bps_rd=0 bps_wr=0 iops=0 iops_rd=0 iops_wr=0
floppy0: removable=1 locked=0 tray-open=0 [not inserted]
sd0: removable=1 locked=0 tray-open=0 [not inserted]
After:
(qemu) info block
ide0-hd0: /tmp/overlay.qcow2 (qcow2, encrypted)
Backing file: /tmp/backing.img (chain depth: 1)
I/O limits: bps=0 bps_rd=0 bps_wr=0 iops=1024 iops_rd=0 iops_wr=0
ide1-cd0: /home/kwolf/images/iso/Fedora-18-x86_64-Live-Desktop.iso (raw, read-only)
Removable device: not locked, tray closed
floppy0: [not inserted]
Removable device: not locked, tray closed
sd0: [not inserted]
Removable device: not locked, tray closed
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This exposes throughput (in megabits/sec) through QMP.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
With these parameters, user can choose the information to be showed,
to avoid message flood in the monitor.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now human monitor can show image details, include internal
snapshot and backing chain info for every block device.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It was decided to not make this command available in QMP in order to
make clear that this is not supposed to be a stable API and should be
used only for testing and debugging purposes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* bonzini/hw-dirs:
exec: remove useless declarations from memory-internal.h
memory: move core typedefs to qemu/typedefs.h
include: avoid useless includes of exec/ headers
sysemu: avoid proliferation of include/ subdirectories
tpm: reorganize headers and split hardware part
configure: fix TPM logic
acpi.h: make it self contained
acpi: move declarations from pc.h to acpi.h
hw: Add lost ARM core again
Fix failure to create q35 machine
Add linux-headers to QEMU_INCLUDES
arm: fix location of some include files
Conflicts:
configure
aliguori: trivial conflict in configure output
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 4d700430a2 as asked by
Luiz. The patch has been obsoleted by extending MachineInfo structure
by cpu-max field.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
# By Peter Lieven (9) and others
# Via Juan Quintela
* quintela/migration.next: (22 commits)
Use qemu_put_buffer_async for guest memory pages
Add qemu_put_buffer_async
Use writev ops if available
Store the data to send also in iovec
Update bytes_xfer in qemu_put_byte
Add socket_writev_buffer function
Add QemuFileWritevBuffer QemuFileOps
migration: use XBZRLE only after bulk stage
migration: do not search dirty pages in bulk stage
migration: do not sent zero pages in bulk stage
migration: add an indicator for bulk state of ram migration
migration: search for zero instead of dup pages
bitops: unroll while loop in find_next_bit()
buffer_is_zero: use vector optimizations if possible
cutils: add a function to find non-zero content in a buffer
move vector definitions to qemu-common.h
savevm: Fix bugs in the VMSTATE_VBUFFER_MULTIPLY definition
savevm: Add VMSTATE_STRUCT_VARRAY_POINTER_UINT32
savevm: Add VMSTATE_FLOAT64 helpers
savevm: Add VMSTATE_UINTTL_EQUAL helper
...
during bulk stage of ram migration if a page is a
zero page do not send it at all.
the memory at the destination reads as zero anyway.
even if there is an madvise with QEMU_MADV_DONTNEED
at the target upon receipt of a zero page I have observed
that the target starts swapping if the memory is overcommitted.
it seems that the pages are dropped asynchronously.
this patch also updates QMP to return the number of
skipped pages in MigrationStats.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
These commands return the maximum number of CPUs supported by the
currently running emulator instance, as defined in its QEMUMachine
struct.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This patch adds support for TPM command line options.
The command line options supported here are
./qemu-... -tpmdev passthrough,path=<path to TPM device>,id=<id>
-device tpm-tis,tpmdev=<id>,id=<other id>
and
./qemu-... -tpmdev help
where the latter works similar to -soundhw help and shows a list of
available TPM backends (for example 'passthrough').
Using the type parameter, the backend is chosen, i.e., 'passthrough' for the
passthrough driver. The interpretation of the other parameters along
with determining whether enough parameters were provided is pushed into
the backend driver, which needs to implement the interface function
'create' and return a TPMDriverOpts structure if the VM can be started or
'NULL' if not enough or bad parameters were provided.
Monitor support for 'info tpm' has been added. It for example prints the
following:
(qemu) info tpm
TPM devices:
tpm0: model=tpm-tis
\ tpm0: type=passthrough,path=/dev/tpm0,cancel-path=/sys/devices/pnp0/00:09/cancel
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Corey Bryant <coreyb@linux.vnet.ibm.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Message-id: 1361987275-26289-2-git-send-email-stefanb@linux.vnet.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
New device, has never been released, so we can still improve things
without worrying about compatibility.
Naming is a mess. The code calls the device driver CirMemCharDriver,
the public API calls it "memory", "memchardev", or "memchar", and the
special commands are named like "memchar-FOO". "memory" is a
particularly unfortunate choice, because there's another character
device driver called MemoryDriver. Moreover, the device's distinctive
property is that it's a ring buffer, not that's in memory. Therefore:
* Rename CirMemCharDriver to RingBufCharDriver, and call the thing a
"ringbuf" in the API.
* Rename QMP and HMP commands from memchar-FOO to ringbuf-FOO.
* Rename device parameter from maxcapacity to size (simple words are
good for you).
* Clearly mark the parameter as optional in documentation.
* Fix error reporting so that chardev-add reports to current monitor,
not stderr.
* Replace cirmem in C identifiers by ringbuf.
* Rework documentation. Document the impact of our crappy UTF-8
handling on reading.
* QMP examples that even work.
I could split this up into multiple commits, but they'd change the
same documentation lines multiple times. Not worth it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The data returned has a well-defined size, which makes the size
returned along with it redundant at best. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Command memchar-write takes data and size parameter. Begs the
question what happens when data doesn't match size.
With format base64, qmp_memchar_write() copies the full data argument,
regardless of size argument.
With format utf8, qmp_memchar_write() copies size bytes from data,
happily reading beyond data. Copies crap from the heap or even
crashes.
Drop the size parameter, and always copy the full data argument.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Paolo Bonzini (14) and others
# Via Kevin Wolf
* kwolf/for-anthony: (24 commits)
ide: Add fall through annotations
block: Create proper size file for disk mirror
ahci: Add migration support
ahci: Change data types in preparation for migration
ahci: Remove unused AHCIDevice fields
hbitmap: add assertion on hbitmap_iter_init
mirror: do nothing on zero-sized disk
block/vdi: Check for bad signature
block/vdi: Improved return values from vdi_open
block/vdi: Improve debug output for signature
block: Use error code EMEDIUMTYPE for wrong format in some block drivers
block: Add special error code for wrong format
mirror: support arbitrarily-sized iterations
mirror: support more than one in-flight AIO operation
mirror: add buf-size argument to drive-mirror
mirror: switch mirror_iteration to AIO
mirror: allow customizing the granularity
block: allow customizing the granularity of the dirty bitmap
block: return count of dirty sectors, not chunks
mirror: perform COW if the cluster size is bigger than the granularity
...
This makes sense when the next commit starts using the extra buffer space
to perform many I/O operations asynchronously.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The desired granularity may be very different depending on the kind of
operation (e.g. continuous replication vs. collapse-to-raw) and whether
the VM is expected to perform lots of I/O while mirroring is in progress.
Allow the user to customize it, while providing a sane default so that
in general there will be no extra allocated space in the target compared
to the source.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Next commit will re-enable balloon stats with a different interface, but
this old code conflicts with it. Let's drop it.
It's important to note that the QMP and HMP interfaces are also dropped
by this commit. That shouldn't be a problem though, because:
1. All QMP fields are optional
2. This feature has always been disabled
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This patch change all info call back function to take
additional QDict * parameter, which allow those command
take parameter. Now it is set to NULL at default case.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Add chardev-add and chardev-remove commands to the human monitor.
chardev-add accepts the same syntax as -chardev, chardev-remove
expects a chardev id.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move public headers to include/net, and leave private headers in net/.
Put the virtio headers in include/net/tap.h, removing the multiple copies
that existed. Leave include/net/tap.h as the interface for NICs, and
net/tap_int.h as the interface for OS-specific parts of the tap backend.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Touching char/char.h basically causes the whole of QEMU to
be rebuilt. Avoid this, it is usually unnecessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* kwolf/for-anthony: (32 commits)
osdep: Less restrictive F_SEFL in qemu_dup_flags()
qemu-iotests: add testcases for mirroring on-source-error/on-target-error
qmp: add pull_event function
mirror: add support for on-source-error/on-target-error
iostatus: forward block_job_iostatus_reset to block job
qemu-iotests: add mirroring test case
mirror: implement completion
qmp: add drive-mirror command
mirror: introduce mirror job
block: introduce BLOCK_JOB_READY event
block: add block-job-complete
block: rename block_job_complete to block_job_completed
block: export dirty bitmap information in query-block
block: introduce new dirty bitmap functionality
block: add bdrv_open_backing_file
block: add bdrv_query_stats
block: add bdrv_query_info
qemu-config: Add new -add-fd command line option
monitor: Prevent removing fd from set during init
monitor: Enable adding an inherited fd to an fd set
...
Conflicts:
vl.c
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
On sparc targets, info cpus returns this kind of output:
| info cpus
| * CPU #0: pc=0x0000000000424d18pc=0x0000000000424d18npc=0x0000000000424d1c thread_id=19460
pc is printed twice, there is no space between pc, pc and npc.
With this patch, pc is not printed anymore when has_npc is set. In addition
the space is printed before pc/nip/npc/PC instead of after the colon so that
multiple prints are possible. This result on the following kind of input on
sparc targets:
| info cpus
| * CPU #0: pc=0x0000000000424d18 npc=0x0000000000424d1c thread_id=19460
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Error management is important for mirroring; otherwise, an error on the
target (even something as "innocent" as ENOSPC) requires to start again
with a full copy. Similar to on_read_error/on_write_error, two separate
knobs are provided for on_source_error (reads) and on_target_error (writes).
The default is 'report' for both.
The 'ignore' policy will leave the sector dirty, so that it will be
retried later. Thus, it will not cause corruption.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds the monitor commands that start the mirroring job.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
While streaming can be dropped as soon as it progressed through the whole
image, mirroring needs to be completed manually for two reasons: 1) so that
management knows exactly when the VM switches to the target; 2) because
for other use cases such as replication, we may leave the operation running
for the whole life of the virtual machine.
Add a new block job command that manually completes background operations.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* kwolf/for-anthony: (30 commits)
qemu-iotests: add tests for streaming error handling
qemu-iotests: map underscore to dash in QMP argument names
blkdebug: process all set_state rules in the old state
stream: add on-error argument
block: introduce block job error
iostatus: reorganize io error code
iostatus: change is_read to a bool
iostatus: move BlockdevOnError declaration to QAPI
iostatus: rename BlockErrorAction, BlockQMPEventAction
qemu-iotests: add test for pausing a streaming operation
qmp: add block-job-pause and block-job-resume
block: add support for job pause/resume
qmp: add 'busy' member to BlockJobInfo
block: add block_job_query
block: move job APIs to separate files
block: fix documentation of block_job_cancel_sync
qerror/block: introduce QERR_BLOCK_JOB_NOT_ACTIVE
qemu-iotests: add initial tests for live block commit
QAPI: add command for live block commit, 'block-commit'
block: helper function, to find the base image of a chain
...
This patch adds support for error management to streaming.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add QMP commands matching the functionality.
Paused jobs cannot be canceled without first resuming them. This
ensures that I/O errors are never missed by management. However, an
optional force argument can be specified to allow that.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before the qapi conversion, the sendkey command could be used to
send key codes in hex directly to the guest. In HMP, this would
be like:
(qemu) sendkey 0xdc
However, the qapi conversion broke this, as it only supports sending
QKeyCode values to the guest. That's a regression.
This commit fixes the problem by adding hex value support down
the QMP interface, qmp_send_key().
In more detail, this commit:
1. Adds the KeyValue union. This can represent an hex value or
a QKeyCode value
2. *Changes* the QMP send-key command to take an KeyValue argument
instead of a QKeyCode one
3. Adapt hmp_send_key() to the QMP interface changes
Item 2 is an incompatible change, but as we're in development phase
(and this command has been merged a few weeks ago) this shouldn't be
a problem.
Finally, it's not possible to split this commit without breaking the
build.
Reported-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Today, it's necessary to specify the protocol you want to use
when dumping the guest memory, for example:
(qemu) dump-guest-memory file:/tmp/guest-memory
This has a few issues:
1. It's cumbersome to type
2. We loose file path autocompletion
3. Being able to specify fd:X in HMP makes little sense for humans
Because of these reasons, hardcode the 'protocol' argument to
'file:' in HMP.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
* 'spice.v59' of git://anongit.freedesktop.org/spice/qemu:
Remove #ifdef QXL_COMMAND_FLAG_COMPAT_16BPP
qxl: Add set_client_capabilities() interface to QXLInterface
spice: make number of surfaces runtime-configurable.
configure: print spice-protocol and spice-server versions
qxl: add QXL_IO_MONITORS_CONFIG_ASYNC
qxl: disallow unknown revisions
qxl/update_area_io: guest_bug on invalid parameters
spice: increase the verbosity of spice section in "qemu --help"
spice: adding seamless-migration option to the command line
spice: add 'migrated' flag to spice info
spice migration: add QEVENT_SPICE_MIGRATE_COMPLETED
spice: notify on vm state change only via spice_server_vm_start/stop
spice: notify spice server on vm start/stop
spice: abort on invalid streaming cmdline params
Convert 'sendkey' to use QAPI.
QAPI passes key's index of mapping table to qmp_send_key(),
not keycode. So we use help functions to convert key/code to
index of key_defs, and 'index' will be converted to 'keycode'
inside qmp_send_key().
For qmp, QAPI would check invalid key and raise error.
For hmp, invalid key is checked in hmp_send_key().
'send-key' of QMP doesn't support key in hexadecimal format.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The flag is 'true' when spice migration has completed on the src side.
It is needed for a case where libvirt dies before migration completes
and it misses the event QEVENT_SPICE_MIGRATE_COMPLETED.
When libvirt is restored and queries the migration status, it also needs
to query spice and check if its migration has completed.
Signed-off-by: Yonit Halperin <yhalperi@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* qmp/queue/qmp: (48 commits)
target-ppc: add implementation of query-cpu-definitions (v2)
target-i386: add implementation of query-cpu-definitions (v2)
qapi: add query-cpu-definitions command (v2)
compiler: add macro for GCC weak symbols
qapi: add query-machines command
qapi: mark QOM commands stable
qmp: introduce device-list-properties command
qmp: add SUSPEND_DISK event
qmp: qmp-events.txt: add missing doc for the SUSPEND event
qmp: qmp-events.txt: put events in alphabetical order
qmp: emit the WAKEUP event when the guest is put to run
qmp: don't emit the RESET event on wakeup from S3
scripts: qapi-commands.py: qmp-commands.h: include qdict.h
docs: writing-qmp-commands.txt: update error section
error, qerror: drop QDict member
qerror: drop qerror_table and qerror_format()
error, qerror: pass desc string to error calls
error: drop error_get_qobject()/error_set_qobject()
qemu-ga: switch to the new error format on the wire
qmp: switch to the new error format on the wire
...
The error_is_type() function is going to be dropped.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
It's not needed. As the device name is already known, we can replace
the duplicated password prompting code by monitor_read_block_device_key().
This overly simplifies hmp_change().
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This commit changes hmp_cont() to loop through all block devices
and proactively set an encryption key for any encrypted device
missing a key.
This change is needed because QERR_DEVICE_ENCRYPTED is going to be
dropped by a future commit.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Change XBZRLE cache size in bytes (the size should be a power of 2, it will be
rounded down to the nearest power of 2).
If XBZRLE cache size is too small there will be many cache miss.
New query-migrate-cache-size QMP command and 'info migrate_cache_size' HMP
command to query cache value.
Signed-off-by: Benoit Hudzia <benoit.hudzia@sap.com>
Signed-off-by: Petter Svard <petters@cs.umu.se>
Signed-off-by: Aidan Shribman <aidan.shribman@sap.com>
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The management can enable/disable a capability for the next migration by using
migrate-set-capabilities QMP command.
The user can use migrate_set_capability HMP command.
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The management can query the current migration capabilities using
query-migrate-capabilities QMP command.
The user can use 'info migrate_capabilities' HMP command.
Currently only XBZRLE capability is available.
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
We add time spent for migration to the output of "info migrate"
command. 'total_time' means time since the start fo migration if
migration is 'active', and total time of migration if migration is
completed. As we are also interested in transferred ram when
migration completes, adding all ram statistics
Signed-off-by: Juan Quintela <quintela@redhat.com>
This is needed to get file descriptors from SCM_RIGHTS.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This is not a full QAPI conversion, but an intermediate step.
In essence, do_netdev_add() is split into three functions:
1. netdev_add(): performs the actual work. This function is fully
converted to Error (thus, it's "qapi-friendly")
2. qmp_netdev_add(): the QMP front-end for netdev_add(). This is
coded by hand and not auto-generated (gen=no in the schema). The
reason for this it's a lot easier and simpler to with QemuOpts
this way
3. hmp_netdev_add(): HMP front-end.
This design was suggested by Paolo Bonzini.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
The command's usage:
dump-guest-memory [-p] protocol [begin] [length]
The supported protocol can be file or fd:
1. file: the protocol starts with "file:", and the following string is
the file's path.
2. fd: the protocol starts with "fd:", and the following string is the
fd's name.
Note:
1. If you want to use gdb to process the core, please specify -p option.
The reason why the -p option is not default is:
a. guest machine in a catastrophic state can have corrupted memory,
which we cannot trust.
b. The guest machine can be in read-mode even if paging is enabled.
For example: the guest machine uses ACPI to sleep, and ACPI sleep
state goes in real-mode.
2. If you don't want to dump all guest's memory, please specify the start
physical address and the length.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The change of the argument name from value to speed was not propagated there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add mouse_mode, either server or mouse, to qmp and hmp commands, based
on spice_server_is_server_mouse added in spice-server 0.10.3.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Allow streaming operations to be started with an initial speed limit.
This eliminates the window of time between starting streaming and
issuing block-job-set-speed. Users should use the new optional 'speed'
parameter instead so that speed limits are in effect immediately when
the job starts.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The migrate command is one of those commands where HMP and QMP completely
mix up together. This made the conversion to the QAPI (which separates the
command into QMP and HMP parts) a bit difficult.
The first important change to be noticed is that this commit completes the
removal of the Monitor object from migration code, started by the previous
commit.
Another important and tricky change is about supporting the non-detached
mode. That is, if the user doesn't pass '-d' the migrate command will lock
the monitor and will only release it when migration is finished.
To support this in the new HMP command (hmp_migrate()), it is necessary
to create a timer which runs every second and checks if the migration is
still active. If it is, the timer callback will re-schedule itself to run
one second in the future. If the migration has already finished, the
monitor lock is released and the user can use it normally.
All these changes should be transparent to the user.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Simplify the blockdev-snapshot-sync code and gain failsafe operation
by turning it into a wrapper around the new transaction command. A new
option is also added matching "mode".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the system_wakeup monitor command which will simply
wake up suspended guests.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add query-block-jobs, which shows the progress of ongoing block device
operations.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add block_job_cancel, which stops an active block streaming operation.
When the operation has been cancelled the new BLOCK_JOB_CANCELLED event
is emitted.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add block_job_set_speed, which sets the maximum speed for a background
block operation.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add the block_stream command, which starts copy backing file contents
into the image file. Also add the BLOCK_JOB_COMPLETED QMP event which
is emitted when image streaming completes. Later patches add control
over the background copy speed, cancelation, and querying running
streaming operations.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All files under GPLv2 will get GPLv2+ changes starting tomorrow.
event_notifier.c and exec-obsolete.h were only ever touched by Red Hat
employees and can be relicensed now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Remember the original PciInfoList in info_list and use
the info variable to traverse the list.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Unfortunately, this conversion required an additional change.
In the old QMP command, the 'snapshot-file' argument is specified as
optional. The idea is to take the snapshot internally if 'snapshot-file'
is not passed. However, internal snapshots are not supported yet so
the command returns a MissingParamater error if 'snapshot-file' is not
passed. Which makes the argument actually required and will cause
compatibility breakage if we change that in the future.
To fix this the QAPI converted blockdev_snapshot_sync command makes the
'snapshot-file' argument required. Again, in practice it's actually required,
so this is not incompatible.
If we do implement internal snapshots someday, we'll need a new argument
for it.
Note that this discussion doesn't affect HMP.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Note that the command being dropped uses the deprecated MONITOR_CMD_ASYNC
API, but the new command is a regular synchronous command. There shouldn't
be visible differences though, as MONITOR_CMD_ASYNC is internal only.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Please, note that the QMP command has a new 'cpu-index' parameter.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This also fixes a bug with the old version: QMP would invert device id
and vendor id. This would look ok on HMP because it was printing
"device:vendor" instead of "vendor:device".
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Please, note that some of the code supporting memory statistics is
still around (eg. virtio_balloon_receive_stats() and reset_stats()).
Also, the qmp_query_balloon() function is synchronous and thus doesn't
make any use of the (not fully working) monitor's asynchronous command
support (the old non-qapi implementation did).
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
