When booting directly into a kernel, bypassing the boot loader, the CPU and
UART clocks are not set up correctly. This makes the system appear very
slow, and causes the initrd boot test to fail when optimization is off.
The UART clock must run at 24 MHz. The default 25 MHz reference clock
cannot achieve this, so switch to PLL2/2 @ 480 MHz, which works
perfectly with the default /20 divider.
The CPU clock should run at 800 MHz, so switch it to PLL1/2. PLL1 runs
at 800 MHz by default, so we need to double the feedback divider as well
to make it run at 1600 MHz (so PLL1/2 runs at 800 MHz).
We don't bother checking for PLL lock because we know our emulated PLLs
lock instantly.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-13-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements a device model for the NPCM7xx SPI flash controller.
Direct reads and writes, and user-mode transactions have been tested in
various modes. Protection features are not implemented yet.
All the FIU instances are available in the SoC's address space,
regardless of whether or not they're connected to actual flash chips.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-11-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This just implements the bare minimum to cause the boot block to skip
memory initialization.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-10-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports reading and writing OTP fuses and keys. Only fuse reading
has been tested. Protection is not implemented.
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-9-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds two new machines, both supported by OpenBMC:
- npcm750-evb: Nuvoton NPCM750 Evaluation Board.
- quanta-gsj: A board with a NPCM730 chip.
They rely on the NPCM7xx SoC device to do the heavy lifting. They are
almost completely identical at the moment, apart from the SoC type,
which currently only changes the reset contents of one register
(GCR.MDLR), but they might grow apart a bit more as more functionality
is added.
Both machines can boot the Linux kernel into /bin/sh.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-6-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
TYPE_ARM_SSE is a TYPE_SYS_BUS_DEVICE subclass, but
ARMSSEClass::parent_class is declared as DeviceClass.
It never caused any problems by pure luck:
We were not setting class_size for TYPE_ARM_SSE, so class_size of
TYPE_SYS_BUS_DEVICE was being used (sizeof(SysBusDeviceClass)).
This made the system allocate enough memory for TYPE_ARM_SSE
devices even though ARMSSEClass was too small for a sysbus
device.
Additionally, the ARMSSEClass::info field ended up at the same
offset as SysBusDeviceClass::explicit_ofw_unit_address. This
would make sysbus_get_fw_dev_path() crash for the device.
Luckily, sysbus_get_fw_dev_path() never gets called for
TYPE_ARM_SSE devices, because qdev_get_fw_dev_path() is only used
by the boot device code, and TYPE_ARM_SSE devices don't appear at
the fw_boot_order list.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200826181006.4097163-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename TYPE_ARMSSE to TYPE_ARM_SSE, and ARMSSE*() type checking
macros to ARM_SSE*().
This will avoid a future conflict between an ARM_SSE() type
checking macro and the ARMSSE typedef name.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-26-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros:
ASPEED_GPIO
ASPEED_I2C
ASPEED_RTC
ASPEED_SCU
ASPEED_SDHCI
ASPEED_SDMC
ASPEED_VIC
ASPEED_WDT
ASPEED_XDMA
This needs to be addressed to allow us to transform the QOM type
check macros into functions generated by OBJECT_DECLARE_TYPE().
Rename all the constants to ASPEED_DEV_*, to avoid conflicts.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (AW_H3_CCU, AW_H3_SYSCTRL). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to AW_H3_DEV_*, to avoid conflicts.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
HAD is a mandatory features with SMMUv3.1 if S1P is set, which is
our case. Other 3.1 mandatory features come with S2P which we don't
have.
So let's support HAD and advertise SMMUv3.1 support in AIDR.
HAD support allows the CD to disable hierarchical attributes, ie.
if the HAD0/1 bit is set, the APTable field of table descriptors
walked through TTB0/1 is ignored.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the support for AIDR register. It currently advertises
SMMU V3.0 spec.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enhance the smmu_iotlb_inv_iova() helper with range invalidation.
This uses the new fields passed in the NH_VA and NH_VAA commands:
the size of the range, the level and the granule.
As NH_VA and NH_VAA both use those fields, their decoding and
handling is factorized in a new smmuv3_s1_range_inval() helper.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment each entry in the IOTLB corresponds to a page sized
mapping (4K, 16K or 64K), even if the page belongs to a mapped
block. In case of block mapping this unefficiently consumes IOTLB
entries.
Change the value of the entry so that it reflects the actual
mapping it belongs to (block or page start address and size).
Also the level/tg of the entry is encoded in the key. In subsequent
patches we will enable range invalidation. This latter is able
to provide the level/tg of the entry.
Encoding the level/tg directly in the key will allow to invalidate
using g_hash_table_remove() when num_pages equals to 1.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-6-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a specialized SMMUTLBEntry to store the result of
the PTW and cache in the IOTLB. This structure extends the
generic IOMMUTLBEntry struct with the level of the entry and
the granule size.
Those latter will be useful when implementing range invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-5-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the smmu_get_iotlb_key() helper and the
SMMU_IOTLB_ASID() macro. Also move smmu_get_iotlb_key and
smmu_iotlb_key_hash in the IOTLB related code section.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add two helpers: one to lookup for a given IOTLB entry and
one to insert a new entry. We also move the tracing there.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :)
The machine/board object is where the SD cards are created.
Since the PXA2xx is not qdevified, for now create the cards
in pxa270_init() which is the SoC model.
In the future we will move this to the board model.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705213350.24725-2-f4bug@amsat.org>
The NVIC provides an outbound qemu_irq "SYSRESETREQ" which it signals
when the guest sets the SYSRESETREQ bit in the AIRCR register. This
matches the hardware design (where the CPU has a signal of this name
and it is up to the SoC to connect that up to an actual reset
mechanism), but in QEMU it mostly results in duplicated code in SoC
objects and bugs where SoC model implementors forget to wire up the
SYSRESETREQ line.
Provide a default behaviour for the case where SYSRESETREQ is not
actually connected to anything: use qemu_system_reset_request() to
perform a system reset. This will allow us to remove the
implementations of SYSRESETREQ handling from the boards where that's
exactly what it does, and also fixes the bugs in the board models
which forgot to wire up the signal:
* microbit
* mps2-an385
* mps2-an505
* mps2-an511
* mps2-an521
* musca-a
* musca-b1
* netduino
* netduinoplus2
We still allow the board to wire up the signal if it needs to, in case
we need to model more complicated reset controller logic or to model
buggy SoC hardware which forgot to wire up the line itself. But
defaulting to "reset the system" is more often going to be correct
than defaulting to "do nothing".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-3-peter.maydell@linaro.org
Control this cpu feature via a machine property, much as we do
with secure=on, since both require specialized support in the
machine setup to be functional.
Default MTE to off, since this feature implies extra overhead.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'cpu_type' has been moved from BCM283XState to BCM283XClass
in commit 210f47840d, but we forgot to remove the old variable.
Do it now.
Fixes: 210f47840d ("hw/arm/bcm2836: Hardcode correct CPU type")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200703200459.23294-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of using printf() for logging guest accesses to invalid
register offsets in the pxa2xx PIC device, use the usual
qemu_log_mask(LOG_GUEST_ERROR,...).
This was the only user of the REG_FMT macro in pxa.h, so we can
remove that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-16-peter.maydell@linaro.org
Instead of logging guest accesses to invalid register offsets in this
device using zaurus_printf() (which just prints to stderr), use the
usual qemu_log_mask(LOG_GUEST_ERROR,...).
Since this was the only use of the zaurus_printf() macro outside
spitz.c, we can move the definition of that macro from sharpsl.h
to spitz.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-14-peter.maydell@linaro.org
The flash device is exclusively for the host-controlled firmware, so
we should not expose it to the OS. Exposing it risks the OS messing
with it, which could break firmware runtime services and surprise the
OS when all its changes disappear after reboot.
As firmware needs the device and uses DT, we leave the device exposed
there. It's up to firmware to remove the nodes from DT before sending
it on to the OS. However, there's no need to force firmware to remove
tables from ACPI (which it doesn't know how to do anyway), so we
simply don't add the tables in the first place. But, as we've been
adding the tables for quite some time and don't want to change the
default hardware exposed to versioned machines, then we only stop
exposing the flash device tables for 5.1 and later machine types.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20200629140938.17566-4-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the virtio-iommu translates MSI transactions.
This behavior is inherited from ARM SMMU. The virt machine
code knows where the guest MSI doorbells are so we can easily
declare those regions as VIRTIO_IOMMU_RESV_MEM_T_MSI. With that
setting the guest will not map MSIs through the IOMMU and those
transactions will be simply bypassed.
Depending on which MSI controller is in use (ITS or GICV2M),
we declare either:
- the ITS interrupt translation space (ITS_base + 0x10000),
containing the GITS_TRANSLATOR or
- The GICV2M single frame, containing the MSI_SETSP_NS register.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20200629070404.10969-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add properties to the i.MX6UL processor to be able to select a
particular PHY on the MDIO bus for each FEC device.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: ea1d604198b6b73ea6521676e45bacfc597aba53.1593296112.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedMachineState seems crippled. We use incorrectly 2
different structures to do the same thing. Merge them
altogether:
- Move AspeedMachine fields to AspeedMachineState
- AspeedMachineState is now QOM
- Remove unused AspeedMachine structure
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072132.2868-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To have a more consistent naming, rename AspeedBoardState
as AspeedMachineState.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072132.2868-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The number of MACs supported by an Aspeed SoC is defined by "macs_num"
under the SoC model, that is two for the AST2400 and AST2500 and four
for the AST2600. The model initializes the maximum number of supported
MACs but the number of realized devices is capped by the number of
network device back-ends defined on the command line. This can leave
unrealized devices hanging around in the QOM composition tree.
To get virtual hardware that matches the physical hardware, you have
to pass exactly as many -nic options as there are MACs, and some of
them must be -nic none:
* Machines ast2500-evb, palmetto-bmc, romulus-bmc, sonorapass-bmc,
swift-bmc, and witherspoon-bmc: two -nic, and the second one must be
-nic none.
* Machine ast2600-evb: four -nic, the first one must be -nic none.
* Machine tacoma-bmc: four nic, the first two and the last one must be
-nic none.
Modify the machine initialization to define which MACs are attached to
a network device back-end using a bit-field property "macs-mask" and
let the SoC realize all network devices.
The default setting of "macs-mask" is "use MAC0" only, which works for
all our AST2400 and AST2500 machines. The AST2600 machines have
different configurations. The AST2600 EVB machine activates MAC1, MAC2
and MAC3 and the Tacoma BMC machine activates MAC2.
Incompatible CLI change: -nic options now apply to *active* MACs:
MAC1, MAC2, MAC3 for ast2600-evb, MAC2 for tacoma-bmc, and MAC0 for
all the others.
The machines now always get all MACs as they should. Visible in "info
qom-tree", here's the change for tacoma-bmc:
/machine (tacoma-bmc-machine)
/peripheral (container)
/peripheral-anon (container)
/soc (ast2600-a1)
[...]
/ftgmac100[0] (ftgmac100)
/ftgmac100[0] (qemu:memory-region)
/ftgmac100[1] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
/ftgmac100[2] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
/ftgmac100[3] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
[...]
/mii[0] (aspeed-mmi)
/aspeed-mmi[0] (qemu:memory-region)
/mii[1] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
/mii[2] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
/mii[3] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
Also visible in "info qtree"; here's the change for tacoma-bmc:
dev: ftgmac100, id ""
gpio-out "sysbus-irq" 1
aspeed = true
- mac = "52:54:00:12:34:56"
- netdev = "hub0port0"
+ mac = "52:54:00:12:34:57"
+ netdev = ""
mmio 000000001e660000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:58"
netdev = ""
+ mmio 000000001e680000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
- netdev = ""
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:56"
+ netdev = "hub0port0"
+ mmio 000000001e670000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:59"
netdev = ""
+ mmio 000000001e690000/0000000000002000
[...]
dev: aspeed-mmi, id ""
mmio 000000001e650000/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650008/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650010/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650018/0000000000000008
Inactive MACs will have no peer and QEMU may warn the user with :
qemu-system-arm: warning: nic ftgmac100.0 has no peer
qemu-system-arm: warning: nic ftgmac100.1 has no peer
qemu-system-arm: warning: nic ftgmac100.3 has no peer
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[Commit message expanded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-6-armbru@redhat.com>
Commit ece09beec4 ("aspeed: introduce a configurable number of CPU
per machine") was a convient change during bringup but the Aspeed SoCs
have a fixed number of CPUs : one for the AST2400 and AST2500, and two
for the AST2600.
When the number of CPUs configured with -smp is less than the SoC's
fixed number, the "unconfigured" CPUs are left unrealized. This can
happen for machines ast2600-evb and tacoma-bmc, where the SoC's fixed
number is 2. To get virtual hardware that matches the physical
hardware, you have to pass -smp cpus=2 (or its sugared form -smp 2).
We normally reject -smp cpus=N when N exceeds the machine's limit.
Except we ignore cpus=2 (and only cpus=2) with a warning for machines
ast2500-evb, palmetto-bmc, romulus-bmc, sonorapass-bmc, swift-bmc, and
witherspoon-bmc.
Remove the "num-cpu" property from the SoC state and use the fixed
number of CPUs defined in the SoC class instead. Compute the default,
min, max number of CPUs of the machine directly from the SoC class
definition.
Machines ast2600-evb and tacoma-bmc now always get their second CPU as
they should. Visible in "info qom-tree"; here's the change for
ast2600-evb:
/machine (ast2600-evb-machine)
/peripheral (container)
/peripheral-anon (container)
/soc (ast2600-a1)
/a7mpcore (a15mpcore_priv)
/a15mp-priv-container[0] (qemu:memory-region)
/gic (arm_gic)
/gic_cpu[0] (qemu:memory-region)
/gic_cpu[1] (qemu:memory-region)
+ /gic_cpu[2] (qemu:memory-region)
/gic_dist[0] (qemu:memory-region)
/gic_vcpu[0] (qemu:memory-region)
/gic_viface[0] (qemu:memory-region)
/gic_viface[1] (qemu:memory-region)
+ /gic_viface[2] (qemu:memory-region)
/unnamed-gpio-in[0] (irq)
[...]
+ /unnamed-gpio-in[160] (irq)
[same for 161 to 190...]
+ /unnamed-gpio-in[191] (irq)
Also visible in "info qtree"; here's the change for ast2600-evb:
bus: main-system-bus
type System
dev: a15mpcore_priv, id ""
gpio-in "" 128
- gpio-out "sysbus-irq" 5
- num-cpu = 1 (0x1)
+ gpio-out "sysbus-irq" 10
+ num-cpu = 2 (0x2)
num-irq = 160 (0xa0)
mmio 0000000040460000/0000000000008000
dev: arm_gic, id ""
- gpio-in "" 160
- num-cpu = 1 (0x1)
+ gpio-in "" 192
+ num-cpu = 2 (0x2)
num-irq = 160 (0xa0)
revision = 2 (0x2)
has-security-extensions = true
has-virtualization-extensions = true
num-priority-bits = 8 (0x8)
mmio ffffffffffffffff/0000000000001000
mmio ffffffffffffffff/0000000000002000
mmio ffffffffffffffff/0000000000001000
mmio ffffffffffffffff/0000000000002000
mmio ffffffffffffffff/0000000000000100
+ mmio ffffffffffffffff/0000000000000100
+ mmio ffffffffffffffff/0000000000000200
mmio ffffffffffffffff/0000000000000200
The other machines now reject -smp cpus=2 just like -smp cpus=3 and up.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message expanded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-5-armbru@redhat.com>
Wire the dwc-hsotg (dwc2) emulation into Qemu
Signed-off-by: Paul Zimmerman <pauldzim@gmail.com>
Reviewed-by: Philippe Mathieu-Daude <f4bug@amsat.org>
Message-id: 20200520235349.21215-7-pauldzim@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add BCM2835 SOC MPHI (Message-based Parallel Host Interface)
emulation. It is very basic, only providing the FIQ interrupt
needed to allow the dwc-otg USB host controller driver in the
Raspbian kernel to function.
Signed-off-by: Paul Zimmerman <pauldzim@gmail.com>
Acked-by: Philippe Mathieu-Daude <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200520235349.21215-2-pauldzim@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX7 supports watchdog pretimeout interupts. With this commit,
the watchdog in mcimx7d-sabre is fully operational, including
pretimeout support.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-9-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiating PWM, CAN, CAAM, and OCOTP devices is necessary to avoid
crashes when booting mainline Linux.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-8-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this patch, the watchdog on i.MX31 emulations is fully operational.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-5-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this commit, the watchdog on imx25-pdk is fully operational,
including pretimeout support.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a full implementation, move i.MX watchdog driver
from hw/misc to hw/watchdog. While at it, add the watchdog files
to MAINTAINERS.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
RAS Virtualization feature is not supported now, so
add a RAS machine option and disable it by default.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200512030609.19593-3-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the NRF51 series, all peripherals have a fixed I/O size
of 4KiB. Define NRF51_PERIPHERAL_SIZE and use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support to init nvdimm acpi state and build nvdimm acpi tables.
Please note nvdimm_support is not yet enabled.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200421125934.14952-4-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/arm: versal: Add support for the RTC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20200427181649.26851-10-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for SD.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20200427181649.26851-9-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
