When escalating to HardFault, we must go into Lockup if we
can't take the synchronous HardFault because the current
execution priority is already at or below the priority of
HardFault. In v7M HF is always priority -1 so a simple < 0
comparison sufficed; in v8M the priority of HardFault can
vary depending on whether it is a Secure or NonSecure
HardFault, so we must check against the priority of the
HardFault exception vector we're about to use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-13-git-send-email-peter.maydell@linaro.org
In armv7m_nvic_set_pending() we have to compare the
priority of an exception against the execution priority
to decide whether it needs to be escalated to HardFault.
In the specification this is a comparison against the
exception's group priority; for v7M we implemented it
as a comparison against the raw exception priority
because the two comparisons will always give the
same answer. For v8M the existence of AIRCR.PRIS and
the possibility of different PRIGROUP values for secure
and nonsecure exceptions means we need to explicitly
calculate the vector's group priority for this check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-12-git-send-email-peter.maydell@linaro.org
Make the set_prio() function take a bool indicating
whether to pend the secure or non-secure version of a banked
interrupt, and use this to implement the correct banking
semantics for the SHPR registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-11-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
Update the nvic_recompute_state() code to handle the security
extension and its associated banked registers.
Code that uses the resulting cached state (ie the irq
acknowledge and complete code) will be updated in a later
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-9-git-send-email-peter.maydell@linaro.org
For v8M, the NVIC has a new set of registers per interrupt,
NVIC_ITNS<n>. These determine whether the interrupt targets Secure
or Non-secure state. Implement the register read/write code for
these, and make them cause NVIC_IABR, NVIC_ICER, NVIC_ISER,
NVIC_ICPR, NVIC_IPR and NVIC_ISPR to RAZ/WI for non-secure
accesses to fields corresponding to interrupts which are
configured to target secure state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-8-git-send-email-peter.maydell@linaro.org
Update the code in nvic_rettobase() so that it checks the
sec_vectors[] array as well as the vectors[] array if needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-7-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
Instead of looking up the pending priority
in nvic_pending_prio(), cache it in a new state struct
field. The calculation of the pending priority given
the interrupt number is more complicated in v8M with
the security extension, so the caching will be worthwhile.
This changes nvic_pending_prio() from returning a full
(group + subpriority) priority value to returning a group
priority. This doesn't require changes to its callsites
because we use it only in comparisons of the form
execution_prio > nvic_pending_prio()
and execution priority is always a group priority, so
a test (exec prio > full prio) is true if and only if
(execprio > group_prio).
(Architecturally the expected comparison is with the
group priority for this sort of "would we preempt" test;
we were only doing a test with a full priority as an
optimisation to avoid the mask, which is possible
precisely because the two comparisons always give the
same answer.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-5-git-send-email-peter.maydell@linaro.org
With banked exceptions, just the exception number in
s->vectpending is no longer sufficient to uniquely identify
the pending exception. Add a vectpending_is_s_banked bool
which is true if the exception is using the sec_vectors[]
array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1505240046-11454-4-git-send-email-peter.maydell@linaro.org
For the v8M security extension, some exceptions must be banked
between security states. Add the new vecinfo array which holds
the state for the banked exceptions and migrate it if the
CPU the NVIC is attached to implements the security extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
-----BEGIN PGP SIGNATURE-----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=GAd3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20170915' into staging
ppc patch queue 2017-09-15
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
# gpg: Signature made Fri 15 Sep 2017 04:50:00 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20170915:
ppc/kvm: use kvm_vm_check_extension() in kvmppc_is_pr()
spapr_events: use QTAILQ_FOREACH_SAFE() in spapr_clear_pending_events()
spapr_cpu_core: cleaning up qdev_get_machine() calls
spapr_pci: don't create 64-bit MMIO window if we don't need to
spapr_pci: convert sprintf() to g_strdup_printf()
spapr_cpu_core: fail gracefully with non-pseries machine types
xics: fix several error leaks
vfio, spapr: Fix levels calculation
spapr_pci: handle FDT creation errors with _FDT()
spapr_pci: use the common _FDT() helper
spapr: fix CAS-generated reset
ppc/xive: fix OV5_XIVE_EXPLOIT bits
spapr: only update SDR1 once per-cpu during CAS
spapr_pci: use g_strdup_printf()
spapr_pci: drop useless check in spapr_populate_pci_child_dt()
spapr_pci: drop useless check in spapr_phb_vfio_get_loc_code()
hw/ppc/spapr.c: cleaning up qdev_get_machine() calls
net: Add SunGEM device emulation as found on Apple UniNorth
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If object_property_get_link() fails then it allocates an error, which
must be freed before returning. The error_get_pretty() function is
merely an accessor to the error message and doesn't free anything.
The error.h header indicates how to do it right:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In several places we were unconditionally applying the
nvic_gprio_mask() to a priority value. This is incorrect
if the priority is one of the fixed negative priority
values (for NMI and HardFault), so don't do it.
This bug would have caused both NMI and HardFault to be
considered as the same priority and so NMI wouldn't
correctly preempt HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505137930-13255-5-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
For v8M the range 0xe002e000..0xe002efff is an alias region which
for secure accesses behaves like a NonSecure access to the main
SCS region. (For nonsecure accesses including when the security
extension is not implemented, it is RAZ/WI.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-11-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
Fix the following warning:
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: warning: logical not is only applied to the left hand side of this bitwise operator [-Wlogical-not-parentheses]
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^ ~
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses after the '!' to evaluate the bitwise operator first
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses around left hand side expression to silence this warning
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
This logic error meant we were not setting the PTZ
bit when we should -- luckily as the comment suggests
this wouldn't have had any effects beyond making GIC
initialization take a little longer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Message-id: 20170829173226.7625-1-bobby.prani@gmail.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARMv7M architecture specifies that most of the addresses in the
PPB region (which includes the NVIC, systick and system registers)
are not accessible to unprivileged accesses, which should
BusFault with a few exceptions:
* the STIR is configurably user-accessible
* the ITM (which we don't implement at all) is always
user-accessible
Implement this by switching the register access functions
to the _with_attrs scheme that lets us distinguish user
mode accesses.
This allows us to pull the handling of the CCR.USERSETMPEND
flag up to the level where we can make it generate a BusFault
as it should for non-permitted accesses.
Note that until the core ARM CPU code implements turning
MEMTX_ERROR into a BusFault the registers will continue to
act as RAZ/WI to user accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-16-git-send-email-peter.maydell@linaro.org
The armv7m_nvic.h header file was accidentally placed in
include/hw/arm; move it to include/hw/intc to match where
its corresponding .c file lives.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-15-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
Remove an out of date comment which says there's only one
item in the NVIC container region -- we put systick into its
own device object a while back and so now there are two
things in the container.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-6-git-send-email-peter.maydell@linaro.org
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During migration we should transfer ais states to the target guest.
This patch introduces a subsection to kvm_s390_flic_vmstate and new
vmsd for qemu_flic. The ais states need to be migrated only when
ais is supported.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
zPCI instructions and facilities are available since IBM zEnterprise
EC12. To support z/PCI in QEMU we enable zpci, aen and ais facilities
starting with zEC12 GA1. And we always set zpci and aen bits in max cpu
model. Later they might be switched off due to applied real cpu model.
For ais bit, we only provide it in the full cpu model beginning with
zEC12 and defer its enablement in the default cpu model to a later point
in time. At the same time, disable them for 2.9 and older machines.
Because of introducing AIS facility, we could check if it's enabled to
initialize flic->ais_supported with the real value.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Although we have recently vmstatified the migration of some css
infrastructure, for some css entities there is still state to be
migrated left, because the focus was keeping migration stream
compatibility (that is basically everything as-is).
Let us add vmstate helpers and extend existing vmstate descriptions so
that we have everything we need. Let us guard the added state via
css_migration_enabled, so we keep the compatible behavior if css
migration is disabled.
Let's also annotate the bits which do not need to be migrated for better
readability.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170711145441.33925-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's introduce a specialized way to inject adapter interrupts that,
unlike the common interrupt injection method, allows to take the
characteristics of the adapter into account.
For adapters subject to AIS facility:
- for non-kvm case, we handle the suppression for a given ISC in QEMU.
- for kvm case, we pass adapter id to kvm to do airq injection.
Add add tracepoint for suppressed airq and suppressing airq.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to emulate the adapter interruption suppression (AIS)
facility properly, the guest needs to be able to modify the AIS mask.
Interrupt suppression will be handled via the flic (for kvm, via a
recently introduced kernel backend; for !kvm, in the flic code), so
let's introduce a method to change the mode via the flic interface.
We introduce the 'simm' and 'nimm' fields to QEMUS390FLICState
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Co-authored-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit f6f4ce4211 ("s390x: add property adapter_routes_max_batch",
2016-12-09) introduces a common realize (intended to be common for all
the subclasses) for flic, but fails to make sure the kvm-flic which had
its own is actually calling this common realize.
This omission fortunately does not result in a grave problem. The common
realize was only supposed to catch a possible programming mistake by
validating a value of a property set via the compat machine macros. Since
there was no programming mistake we don't need this fixed for stable.
Let's fix this problem by making sure kvm flic honors the realize of its
parent class.
Let us also improve on the error message we would hypothetically emit
when the validation fails.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: f6f4ce4211 ("s390x: add property adapter_routes_max_batch")
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
From the moment it was introduced by commit a2875e6f98 ("s390x/kvm:
implement floating-interrupt controller device", 2013-07-16) the kvm-flic
is not making realize fail properly in case it's impossible to create the
KVM device which basically serves as a backend and is absolutely
essential for having an operational kvm-flic.
Let's fix this by making sure we do proper error propagation in realize.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: a2875e6f98 "s390x/kvm: implement floating-interrupt controller device"
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's vmstatify virtio_ccw_save_config and virtio_ccw_load_config for
flexibility (extending using subsections) and for fun.
To achieve this we need to hack the config_vector, which is VirtIODevice
(that is common virtio) state, in the middle of the VirtioCcwDevice state
representation. This is somewhat ugly, but we have no choice because the
stream format needs to be preserved.
Almost no changes in behavior. Exception is everything that comes with
vmstate like extra bookkeeping about what's in the stream, and maybe some
extra checks and better error reporting.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170703213414.94298-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Previously QEMU open-pic implemented the 4 open-pic timers including
all timer registers, but the timers did not "count" or generate any
interrupts. The patch makes the timers both count and generate
interrupts. The timer clock frequency is fixed at 25MHZ.
--
Responding to V2 patch comments.
- Simplify clock frequency logic and commentary.
- Remove camelCase variables.
- Timer objects now created at init rather than lazily.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICPState objects are currently registered to vmstate as qdev objects.
Their instance ids are hence computed automatically in the migration code,
and thus depends on the order the CPU cores were plugged.
If the destination had its CPU cores plugged in a different order than the
source, then ICPState objects will have different instance_ids and load
the wrong state.
Since CPU objects have a reliable cpu_index which is already used as
instance_id in vmstate, let's use it for ICPState as well.
Please note that this doesn't break migration. Older machine types used to
allocate and realize all ICPState objects at machine init time, for the whole
lifetime of the machine. The qdev instance ids are thus 0,1,2... nr_servers
and happen to map to the vCPU indexes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
