If we detach the kernel drivers on the first set_config, then they will
be still attached when the device gets its initial reset. Causing the drivers
to re-initialize the device after the reset, dirtying the device state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Quoting from: linux/Documentation/ABI/stable/sysfs-bus-usb:
Note that some devices, in violation of the USB spec, have a
configuration with a value equal to 0. Writing 0 to
bConfigurationValue for these devices will install that
configuration, rather then unconfigure the device.
So don't compare the configuration value against 0 to check for unconfigured
devices, instead check for a LIBUSB_ERROR_NOT_FOUND return from
libusb_get_active_config_descriptor().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The guest will issue an initial device reset when the device is attached, but
since the current usb-host-libusb code only actually does the reset when
udev->configuration != 0, and on attach the device is not yet configured,
the reset gets ignored. This means that the device gets passed to the guest
in an unknown state, which is not good.
The udev->configuration check is there because of the release / claim
interfaces done around the libusb_device_reset call, but these are not
necessary. If interfaces are claimed when libusb_device_reset gets called
libusb will release + reclaim them itself.
The usb_host_ep_update call also is not necessary. If the reset succeeds the
original config and interface alt settings will be restored.
Last if the reset fails, that means the device has either disconnected or
morphed into an another device and has been completely re-enumerated,
so it is treated by the host as a new device and our handle is invalid,
so on reset failure we need to call usb_host_nodev().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
# By Paolo Bonzini (2) and Jan Kiszka (1)
# Via Gleb Natapov
* qemu-kvm/uq/master:
kvmvapic: Prevent reading beyond the end of guest RAM
x86: cpuid: reconstruct leaf 0Dh data
x86: fix migration from pre-version 12
Message-id: 1382108641-4862-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Amos Kong
# Via Stefan Hajnoczi
* stefanha/net:
net/rtl8139: update network information when macaddr is changed in guest
net/e1000: update network information when macaddr is changed in guest
net: update nic info during device reset
Message-id: 1382103314-21608-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Fam Zheng (3) and others
# Via Stefan Hajnoczi
* stefanha/block:
vmdk: fix VMFS extent parsing
vmdk: Only read cid from image file when opening
virtio: Remove unneeded memcpy
block/raw-win32: Always use -errno in hdev_open
blockdev: fix cdrom read_only flag
sd: Avoid access to NULL BlockDriverState
hmp: drop bogus "[not inserted]"
Message-id: 1382105915-27735-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Paolo Bonzini (10) and others
# Via Paolo Bonzini
* bonzini/iommu-for-anthony:
exec: remove qemu_safe_ram_ptr
icount: make it thread-safe
icount: document (future) locking rules for icount
icount: prepare the code for future races in calling qemu_clock_warp
icount: reorganize icount_warp_rt
icount: use cpu_get_icount() directly
timer: add timer_mod_anticipate and timer_mod_anticipate_ns
timer: extract timer_mod_ns_locked and timerlist_rearm
timer: make qemu_clock_enable sync between disable and timer's cb
qemu-thread: add QemuEvent
timer: protect timers_state's clock with seqlock
seqlock: introduce read-write seqlock
vga: Mark relevant portio lists regions as coalesced MMIO flushing
cirrus: Mark vga io region as coalesced MMIO flushing
portio: Allow to mark portio lists as coalesced MMIO flushing
compatfd: switch to QemuThread
memory: fix 128 arithmetic in info mtree
Message-id: 1382024935-28297-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Peter Maydell (3) and Ákos Kovács (2)
# Via Paolo Bonzini
* bonzini/configure:
ui/Makefile.objs: delete unnecessary cocoa.o dependency
default-configs/: CONFIG_GDBSTUB_XML removed
Makefile.target: CONFIG_NO_* variables removed
rules.mak: New string testing functions
rules.mak: New logical functions for handling y/n values
# By Gerd Hoffmann (2) and others
# Via Gerd Hoffmann
* spice/spice.v75:
spice: fix multihead support
spice-display: add display channel id to the debug messages.
Fix VNC SASL authentication when using a QXL device
spice: replace use of deprecated API
Message-id: 1382006760-19388-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
The VMFS extent line in description file doesn't have start offset as
FLAT lines does, and it should be defaulted to 0. The flat_offset
variable is initialized to -1, so we need to set it in this case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Previously cid of parent is parsed from image file for every IO request.
We already have L1/L2 cache and don't have assumption that parent image
can be updated behind us, so remove this to get more efficiency.
The parent CID is checked only for once after opening.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
rtl8139 has same problem as e1000, nic info isn't updated when macaddr
is changed in guest.
This patch updates the nic info when the last bit of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If we change macaddr in guest by 'ifconfig eth0 hw ether 12:12:12:34:35:36',
the mac register of e1000 is already updated, but we don't update
network information in qemu. Therefor, the information in monitor
is wrong.
This patch updates nic info when the second part of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
macaddr is reset during device reset, but nic info
isn't updated, this problem exists in e1000 & rtl8139
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Report from valgrind:
==19521== Source and destination overlap in memcpy(0x31d38938, 0x31d38938, 64)
==19521== at 0x4A0A343: memcpy@@GLIBC_2.14 (in
/usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==19521== by 0x42774E: virtio_blk_device_init (virtio-blk.c:686)
==19521== by 0x46EE9E: virtio_device_init (virtio.c:1158)
==19521== by 0x25405E: device_realize (qdev.c:178)
==19521== by 0x2559B5: device_set_realized (qdev.c:699)
==19521== by 0x3A819B: property_set_bool (object.c:1315)
==19521== by 0x3A6CE0: object_property_set (object.c:803)
Valgrind is right: blk == &s->blks, so it is a memcpy of 64 byte with
source == destination which can be removed.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is not needed since the RAM list is not modified anymore by
qemu_get_ram_ptr. Replace it with qemu_get_ram_block.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Computing the deadline of all vm_clocks is somewhat expensive and calls
out to qemu-timer.c; two reasons not to do it in the seqlock's write-side
critical section. This however opens the door for races in setting and
reading vm_clock_warp_start.
To plug them, we need to cover the case where a new deadline slips in
between the call to qemu_clock_deadline_ns_all and the actual modification
of the icount_warp_timer. Restrict changes to vm_clock_warp_start and
the icount_warp_timer's expiration time, to only move them back (which
would simply cause an early wakeup).
If a vm_clock timer is cancelled while CPUs are idle, this might cause the
icount_warp_timer to fire unnecessarily. This is not a problem, after it
fires the timer becomes inactive and the next call to timer_mod_anticipate
will be precise.
In addition to this, we must deactivate the icount_warp_timer _before_
checking whether CPUs are idle. This way, if the "last" CPU becomes idle
during the call to timer_del we will still set up the icount_warp_timer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To prepare for future code changes, move the increment of qemu_icount_bias
outside the "if" statement.
Also, hoist outside the if the check for timers that expired due to the
"warping". The check is redundant when !runstate_is_running(), but
doing it this way helps because the code that increments qemu_icount_bias
will be a critical section.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will help later when we will have to place these calls in
a critical section, and thus call a version of cpu_get_icount()
that does not take the lock.
Reviewed-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These let a user anticipate the deadline of a timer, atomically with
other sites that call the function. This helps avoiding complicated
lock hierarchies.
Reviewed-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After disabling the QemuClock, we should make sure that no QemuTimers
are still in flight. To implement that with light overhead, we resort
to QemuEvent. The caller of disabling will wait on QemuEvent of each
timerlist.
Note, qemu_clock_enable(foo,false) can _not_ be called from timer's cb.
Also, the callers of qemu_clock_enable() should be protected by the BQL.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This emulates Win32 manual-reset events using futexes or conditional
variables. Typical ways to use them are with multi-producer,
single-consumer data structures, to test for a complex condition whose
elements come from different threads:
for (;;) {
qemu_event_reset(ev);
... test complex condition ...
if (condition is true) {
break;
}
qemu_event_wait(ev);
}
Or more efficiently (but with some duplication):
... evaluate condition ...
while (!condition) {
qemu_event_reset(ev);
... evaluate condition ...
if (!condition) {
qemu_event_wait(ev);
... evaluate condition ...
}
}
QemuEvent provides a very fast userspace path in the common case when
no other thread is waiting, or the event is not changing state.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU_CLOCK_VIRTUAL may be read outside BQL. This will make its
foundation, i.e. cpu_clock_offset exposed to race condition.
Using private lock to protect it.
After this patch, reading QEMU_CLOCK_VIRTUAL is thread safe
unless use_icount is true, in which case the existing callers
still rely on the BQL.
Lock rule: private lock innermost, ie BQL->"this lock"
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Seqlock implementation for QEMU. Usage idiom
reader:
do {
start = seqlock_read_begin(&sl);
...
} while (seqlock_read_retry(&sl, start));
writer:
seqlock_write_lock(&sl);
...
seqlock_write_unlock(&sl);
initialization:
seqlock_init(QemuSeqLock *sl, QemuMutex *mutex)
mutex could be NULL if the caller will provide its own protection
for concurrent write sides (typically using the BQL).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the explicit qemu_flush_coalesced_mmio_buffer
calls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the explicit qemu_flush_coalesced_mmio_buffer
calls - the memory core will invoke them now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will enable us to remove all remaining explicit calls of
qemu_flush_coalesced_mmio_buffer in IO handlers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_thread_create already does signal blocking and detaching for us.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mtree_print_mr() calls int128_get64() in 3 places but only 2 places
handle 2^64 correctly.
This fixes the third call of int128_get64().
Cc: qemu-stable@nongnu.org
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On one occasion, hdev_open() returned -1 in case of an unknown error
instead of a proper -errno value. Adjust this to match the behavior of
raw_open() (in raw-win32), which is to return -EINVAL in this case.
Also, change the call to error_setg*() to match the one in raw_open() as
well.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch fixes spice display initialization to handle
multihead properly.
spice-core now keeps track of which QemuConsole has a spice
display channel attached to it and which has not. It also
manages display channel ids.
spice-display looks at all QemuConsoles and will pick up any
graphic console not yet bound to a spice channel (which in practice
are all non-qxl graphic devices).
Result is that
(a) you'll get a spice client window for each graphical device
now (first only without this patch), and
(b) mixing qxl and non-qxl vga cards works properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ui/vnc.c:vnc_display_open() and spice-server/server/reds.c:do_spice_init()
are both calling sasl_server_init(). If spice_server_set_sasl_appname()
hasn't been called, spice-server will call it with "spice" as an appname,
causing cyrus-sasl to try to use a /etc/sasl2/spice.conf config file rather
than the /etc/sasl2/qemu.conf file that QEMU uses.
When using -spice sasl on the command line, QEMU properly calls
spice_server_set_sasl_appname() to set the SASL appname as "qemu",
but when using a QXL device without using SPICE, spice_server_init()
is called from qemu_spice_add_interface() without setting the appname
to "qemu", which then causes the VNC code to try to use spice.conf
instead of qemu.conf.
Signed-off-by: Christophe Fergeau <cfergeau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since 0ebd24e0, cdrom doesn't have read-only on by default, which will
error out when using an read only image. Fix it by setting the default
value when parsing opts.
Reported-by: Edivaldo de Araujo Pereira <edivaldoapereira@yahoo.com.br>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 4f8a066b5f (blockdev: Remove IF_*
check for read-only blockdev_init) added a usage of bdrv_is_read_only()
to sd_init(), which is called for versatilepb, versatileab and
xilinx-zynq-a9 machines among others with NULL argument by default,
causing the new qom-test to fail.
Add a check to prevent this.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 3e9fab690d ("block: Add support for
throttling burst max in QMP and the command line.") introduced bogus
"[not inserted]" output, possibly due to a merge failure. Remove this
artifact.
Output of 'info block'
scsi0-hd0: /images/f18-ppc64.qcow2 (qcow2)
[not inserted]
scsi0-cd2: [not inserted]
Removable device: not locked, tray closed
floppy0: [not inserted]
Removable device: not locked, tray closed
sd0: [not inserted]
Removable device: not locked, tray closed
There will be no additional lines between scsi0-hd0 and
scsi0-cd2.
At the same time, scsi0-hd0 already inserted, but still has
'[not inserted]' flag. This line should be removed.
This patch is to solve this.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Delete an unnecessary dependency for cocoa.o; we already have
a general rule that tells Make that we can build a .o file
from a .m source using an ObjC compiler, so this specific
rule is unnecessary. Further, it is using the dubious construct
"$(SRC_PATH)/$(obj)" to get at the source directory, which will
break when $(obj) is redefined as part of the preparation for
per-object library support.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Makefile.target: Build gdbstub-xml.o only when
TARGET_XML_FILES is not empty.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_NO_* variables replaced with the lnot logical function
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
[PMM: fixed a few CONFIG_NO_* uses that were missed]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add new string testing functions which return a y/n result:
eq : are two strings equal (ignoring leading/trailing space)?
ne : are two strings unequal?
isempty : is a string empty?
notempty : is a string non-empty?
Based on an idea by Ákos Kovács <akoskovacs@gmx.com>.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add new logical functions for handling y/n values like those we
use in CONFIG_FOO variables:
lnot : logical NOT
land : logical AND
lor : logical OR
lxor : logical XOR
leqv : logical equality, inverse of lxor
lif : like Make's $(if) but with an eq-like test
Based on an idea by Ákos Kovács <akoskovacs@gmx.com>.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-ldst-6:
target-alpha: Convert to new ldst opcodes
tcg-ppc64: Support new ldst opcodes
tcg-ppc: Support new ldst opcodes
tcg-ppc64: Convert to le/be ldst helpers
tcg-ppc: Convert to le/be ldst helpers
tcg-ppc64: Use TCGMemOp within qemu_ldst routines
tcg-ppc: Use TCGMemOp within qemu_ldst routines
tcg-arm: Improve GUEST_BASE qemu_ld/st
tcg-arm: Convert to new ldst opcodes
tcg-arm: Tidy variable naming convention in qemu_ld/st
tcg-arm: Convert to le/be ldst helpers
tcg-arm: Use TCGMemOp within qemu_ldst routines
tcg-i386: Support new ldst opcodes
tcg-i386: Remove "cb" output restriction from qemu_st8 for i386
tcg-i386: Tidy softmmu routines
tcg-i386: Use TCGMemOp within qemu_ldst routines
tcg: Use TCGMemOp for TCGLabelQemuLdst.opc
Message-id: 1381620683-4568-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Sebastian Macke
# Via Jia Liu
* jliu/or32:
target-openrisc: Removes a non-conforming behavior for the first page of the memory
target-openrisc: Correct handling of page faults.
Message-id: 1380789702-18935-1-git-send-email-proljc@gmail.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
