Intel(R) VT-d 3.0 spec introduces scalable mode address translation to
replace extended context mode. This patch extends current emulator to
support Scalable Mode which includes root table, context table and new
pasid table format change. Now intel_iommu emulates both legacy mode
and scalable mode (with legacy-equivalent capability set).
The key points are below:
1. Extend root table operations to support both legacy mode and scalable
mode.
2. Extend context table operations to support both legacy mode and
scalable mode.
3. Add pasid tabled operations to support scalable mode.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to contribute much to refine the whole commit.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-2-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Split vhost_user_read(), so only header can be read with
vhost_user_read_header().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190308140454.32437-8-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20190308140454.32437-6-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Take a VhostUserState* that can be pre-allocated, and initialize it
with the associated chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
Message-Id: <20190308140454.32437-4-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Prior to f6deb6d9 "virtio-balloon: Remove unnecessary MADV_WILLNEED on
deflate", the balloon device issued an madvise() MADV_WILLNEED on
pages removed from the balloon. That would hint to the host kernel
that the pages were likely to be needed by the guest in the near
future.
It's unclear if this is actually valuable or not, and so f6deb6d9
removed this, essentially ignoring balloon deflate requests. However,
concerns have been raised that this might cause a performance
regression by causing extra latency for the guest in certain
configurations.
So, until we can get actual benchmark data to see if that's the case,
this restores the old behaviour, issuing a MADV_WILLNEED when a page is
removed from the balloon.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a balloon bug with a nasty consequence - potentially
corrupting guest memory - but which is extremely unlikely to be
triggered in practice.
The balloon always works in 4kiB units, but the host could have a
larger page size on certain platforms. Since ed48c59 "virtio-balloon:
Safely handle BALLOON_PAGE_SIZE < host page size" we've handled this
by accumulating requests to balloon 4kiB subpages until they formed a
full host page. Since f6deb6d "virtio-balloon: Remove unnecessary
MADV_WILLNEED on deflate" we essentially ignore deflate requests.
Suppose we have a host with 8kiB pages, and one host page has subpages
A & B. If we get this sequence of events -
inflate A
deflate A
inflate B
- the current logic will discard the whole host page. That's
incorrect because the guest has deflated subpage A, and could have
written important data to it.
This patch fixes the problem by adjusting our state information about
partially ballooned host pages when deflate requests are received.
Fixes: ed48c59 "virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-3-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
ed48c59875 "virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host
page size" introduced a new temporary data structure which tracks 4kiB
chunks which have been inserted into the balloon by the guest but
don't yet form a full host page which we can discard.
Unfortunately, I had a thinko and allocated that structure with
g_malloc0() but freed it with a plain free() rather than g_free().
This corrects the problem.
Fixes: ed48c59875
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-2-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
The elem could theorically contain both outbuf and inbufs. We move the
free operation to the end of this function to avoid using elem->in_sg
while elem has been freed.
Fixes: c13c4153f7
("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Peter Xu <peterx@redhat.com>
Message-Id: <1552383280-4122-1-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The implementation used blocks units rather than the expected bytes.
Fixes: c03e7ef12a ("nvme: Implement Write Zeroes")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some machines have an SDHCI device, but no PCI. To be able to
compile hw/sd/sdhci.c without CONFIG_PCI, we must not call functions
like pci_get_address_space() and pci_allocate_irq() there. Thus
move the PCI-related code into a separate file.
This is required for the new Kconfig-like build system, e.g. it is
needed if a user wants to compile a QEMU binary with just one machine
that has SDHCI, but no PCI, like the ARM "raspi" machines for example.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This makes vfio_get_region_info_cap() to be used in quirks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190307050518.64968-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Activate only stop0 and stop1 levels. We should not need more levels
when under QEMU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To improve OPAL/skiboot support. We don't need to strictly model these
XSCOM accesses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new class attribute to define XSCOM operations per CPU
family and add a couple of XSCOM addresses controlling the power
management states of the core on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV LPC Controller exposes different sets of registers for
each of the functional units it encompasses, among which the OPB
(On-Chip Peripheral Bus) Master and Arbitrer and the LPC HOST
Controller.
The mapping addresses of each register range are correct but the sizes
are too large. Fix the sizes and define the OPB Arbitrer range to fill
the gap between the OPB Master registers and the LPC HOST Controller
registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PSI bridge on POWER9 is very similar to POWER8. The BAR is still
set through XSCOM but the controls are now entirely done with MMIOs.
More interrupts are defined and the interrupt controller interface has
changed to XIVE. The POWER9 model is a first example of the usage of
the notify() handler of the XiveNotifier interface, linking the PSI
XiveSource to its owning device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the PSI bridge model for POWER9, abstract
the POWER chip differences in a PnvPsi class model and introduce a
specific Pnv8Psi type for POWER8. POWER8 interface to the interrupt
controller is still XICS whereas POWER9 uses the new XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the New World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the Old World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On sPAPR vfio_listener_region_add() is called in 2 situations:
1. a new listener is registered from vfio_connect_container();
2. a new IOMMU Memory Region is added from rtas_ibm_create_pe_dma_window().
In both cases vfio_listener_region_add() calls
memory_region_iommu_replay() to notify newly registered IOMMU notifiers
about existing mappings which is totally desirable for case 1.
However for case 2 it is nothing but noop as the window has just been
created and has no valid mappings so replaying those does not do anything.
It is barely noticeable with usual guests but if the window happens to be
really big, such no-op replay might take minutes and trigger RCU stall
warnings in the guest.
For example, a upcoming GPU RAM memory region mapped at 64TiB (right
after SPAPR_PCI_LIMIT) causes a 64bit DMA window to be at least 128TiB
which is (128<<40)/0x10000=2.147.483.648 TCEs to replay.
This mitigates the problem by adding an "skipping_replay" flag to
sPAPRTCETable and defining sPAPR own IOMMU MR replay() hook which does
exactly the same thing as the generic one except it returns early if
@skipping_replay==true.
Another way of fixing this would be delaying replay till the very first
H_PUT_TCE but this does not work if in-kernel H_PUT_TCE handler is
enabled (a likely case).
When "ibm,create-pe-dma-window" is complete, the guest will map only
required regions of the huge DMA window.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190307050518.64968-2-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reset all regs but keep the MMIO BAR enabled as it is at realize time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple helper to translate XSCOM addresses to MMIO addresses
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The NSR register of the HV ring has a different, although similar, bit
layout. TM_QW3_NSR_HE_PHYS bit should now be raised when the
Hypervisor interrupt line is signaled. Other bits TM_QW3_NSR_HE_POOL
and TM_QW3_NSR_HE_LSI are not modeled. LSI are for special interrupts
reserved for HW bringup and the POOL bit is used when signaling a
group of VPs. This is not currently implemented in Linux but it is in
pHyp.
The most important special commands on the HV TIMA page are added to
let the core manage interrupts : acking and changing the CPU priority.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have different interrupt controllers,
and reporting their state requires calling different helper routines.
However, the interrupt presenters are still handled in the higher
level pic_print_info() routine because they are not related to the
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have a different set of devices and a
different device tree layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine with need to encode the block id in the source
interrupt number before forwarding the source event notification to
the Router.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can perform indirect loads and stores on the TIMA
on behalf of another CPU. Give the controller the possibility to call
the TIMA memory accessors with a XiveTCTX of its choice.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
By default on P9, the HW CAM line (23bits) is hardwired to :
0x000||0b1||4Bit chip number||7Bit Thread number.
When the block group mode is enabled at the controller level (PowerNV),
the CAM line is changed for CAM compares to :
4Bit chip number||0x001||7Bit Thread number
This will require changes in xive_presenter_tctx_match() possibly.
This is a lowlevel functionality of the HW controller and it is not
strictly needed. Leave it for later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Original commit message:
This patch adds an emulation model for i2c controller found on most of the FSL SoCs.
It also integrates the RTC (ds1338) that sits on the i2c Bus with e500 machine model.
Patch was originally written by Amit Singh Tomar <amit.tomar@freescale.com>
see http://patchwork.ozlabs.org/patch/431475/
I only fixed it enough for application on top of current qemu master
20b084c4b1, and hopefully fixed checkpatch errors
Tested by booting Linux kernel 4.20.12. Now e500 machine doesn't need
network time protocol daemon because it will have working RTC
(before all timestamps on files were from 2016)
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Signed-off-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190306102812.28972-1-randrianasulu@gmail.com>
[dwg: Add Kconfig stanza to define the new symbol, update MAINTAINERS]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_CALL H_PAGE_INIT can be used to zero or copy a page of guest
memory. Enable the in-kernel H_PAGE_INIT handler.
The in-kernel handler takes half the time to complete compared to
handling the H_CALL in userspace.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190306060608.19935-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we allocate a hash page table then we know that the guest won't be
using process tables, so set the partition table entry maintained for
the guest to zero. If this isn't done, then the guest radix bit will
remain set in the entry. This means that when the guest calls
H_REGISTER_PROCESS_TABLE there will be a mismatch between then flags
and the value in spapr->patb_entry, and the call will fail. The guest
will then panic:
Failed to register process table (rc=-4)
kernel BUG at arch/powerpc/platforms/pseries/lpar.c:959
The result being that it isn't possible to boot a hash guest on a P9
system.
Also fix a bug in the flags parsing in h_register_process_table() which
was introduced by the same patch, and simplify the handling to make it
less likely that errors will be introduced in the future. The effect
would have been setting the host radix bit LPCR_HR for a hash guest
using process tables, which currently isn't supported and so couldn't
have been triggered.
Fixes: 00fd075e18 "target/ppc/spapr: Set LPCR:HR when using Radix mode"
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190305022102.17610-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are currently 3 mitigations the availability of which is controlled
by the spapr-caps mechanism, cap-cfpc, cap-sbbc, and cap-ibs. Enable these
mitigations by default for the pseries-4.0 machine type.
By now machine firmware should have been upgraded to allow these
settings.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-3-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_caps cap-cfpc, cap-sbbc and cap-ibs are used to control the
availability of certain mitigations to the guest. These haven't been
implemented under TCG, it is unlikely they ever will be, and it is unclear
as to whether they even need to be.
As such, make failure to apply these capabilities under TCG non-fatal.
Instead we print a warning message to the user but still allow the guest
to continue.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-2-sjitindarsingh@gmail.com>
[dwg: Small style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new spapr_cap SPAPR_CAP_CCF_ASSIST to be used to indicate
the requirement for a hw-assisted version of the count cache flush
workaround.
The count cache flush workaround is a software workaround which can be
used to flush the count cache on context switch. Some revisions of
hardware may have a hardware accelerated flush, in which case the
software flush can be shortened. This cap is used to set the
availability of such hardware acceleration for the count cache flush
routine.
The availability of such hardware acceleration is indicated by the
H_CPU_CHAR_BCCTR_FLUSH_ASSIST flag being set in the characteristics
returned from the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_cap SPAPR_CAP_IBS is used to indicate the level of capability
for mitigations for indirect branch speculation. Currently the available
values are broken (default), fixed-ibs (fixed by serialising indirect
branches) and fixed-ccd (fixed by diabling the count cache).
Introduce a new value for this capability denoted workaround, meaning that
software can work around the issue by flushing the count cache on
context switch. This option is available if the hypervisor sets the
H_CPU_BEHAV_FLUSH_COUNT_CACHE flag in the cpu behaviours returned from
the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Enable the large decrementer by default for the pseries-4.0 machine type.
It is disabled again by default_caps_with_cpu() for pre-POWER9 cpus
since they don't support the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-4-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement support to allow KVM guests to take advantage of the large
decrementer introduced on POWER9 cpus.
To determine if the host can support the requested large decrementer
size, we check it matches that specified in the ibm,dec-bits device-tree
property. We also need to enable it in KVM by setting the LPCR_LD bit in
the LPCR. Note that to do this we need to try and set the bit, then read
it back to check the host allowed us to set it, if so we can use it but
if we were unable to set it the host cannot support it and we must not
use the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-3-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior to POWER9 the decrementer was a 32-bit register which decremented
with each tick of the timebase. From POWER9 onwards the decrementer can
be set to operate in a mode called large decrementer where it acts as a
n-bit decrementing register which is visible as a 64-bit register, that
is the value of the decrementer is sign extended to 64 bits (where n is
implementation dependant).
The mode in which the decrementer operates is controlled by the LPCR_LD
bit in the logical paritition control register (LPCR).
>From POWER9 onwards the HDEC (hypervisor decrementer) was enlarged to
h-bits, also sign extended to 64 bits (where h is implementation
dependant). Note this isn't configurable and is always enabled.
On POWER9 the large decrementer and hdec are both 56 bits, as
represented by the lrg_decr_bits cpu class property. Since they are the
same size we only add one property for now, which could be extended in
the case they ever differ in the future.
We also add the lrg_decr_bits property for POWER5+/7/8 since it is used
to determine the size of the hdec, which is only generated on the
POWER5+ processor and later. On these processors it is 32 bits.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add spapr_cap SPAPR_CAP_LARGE_DECREMENTER to be used to control the
availability of the large decrementer for a guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-1-sjitindarsingh@gmail.com>
[dwg: Trivial style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit b8165118f5 broke CPU hotplug tests for old machine types:
$ QTEST_QEMU_BINARY=ppc64-softmmu/qemu-system-ppc64 ./tests/cpu-plug-test -m=slow
/ppc64/cpu-plug/pseries-3.1/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12-sxxm/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-3.0/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.10/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.11/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.9/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.7/device-add/2x3x1&maxcpus=6: **
ERROR:/home/thuth/devel/qemu/hw/ppc/spapr_events.c:313:rtas_event_log_to_source: assertion failed: (source->enabled)
Broken pipe
/home/thuth/devel/qemu/tests/libqtest.c:143: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
Aborted (core dumped)
The approach of faking the availability of OV5_HP_EVT causes the
code to assume the hotplug event source is enabled, which is wrong
for older machines.
We've now fixed CAS under qtest with a different approach. Therefore,
this reverts commit b8165118f5.
A subsequent patch will address the problem of CAS under qtest from
a different angle.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875097.147873.1732264036668112686.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The RTAS event hotplug code for machine types 2.8 and newer depends on
the CAS negotiated ov5 in order to work properly. However, there's no
CAS when running under qtest. There has been a tentative to trick the
code by faking the OV5_HP_EVT bit, but it turned out to break other
assumptions in the code and the change got reverted.
Go for a more general approach and simulate a CAS when running under
qtest. For simplicity, this pseudo CAS simple simulates the case where
the guest supports the same features as the machine. It is done at
reset time, just before we reset the DRCs, which could potentially
exercise the unplug code.
This allows to test unplug on spapr with both older and newer machine
types.
Suggested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875704.147873.10563808578795890265.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "systempagesize" name suggests that it is the host system page size
while it is the smallest page size of memory backing the guest RAM so
let's rename it to stop confusion. This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-4-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current code assumes that we can address more bits on a PCI bus
for DMA than we really can but there is no way knowing the actual limit.
This makes a better guess for the number of levels and if the kernel
fails to allocate that, this increases the level numbers till succeeded
or reached the 64bit limit.
This adds levels to the trace point.
This may cause the kernel to warn about failed allocation:
[65122.837458] Failed to allocate a TCE memory, level shift=28
which might happen if MAX_ORDER is not large enough as it can vary:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/Kconfig?h=v5.0-rc2#n727
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PC machines put firmware in ROM by default. To get it put into
flash memory (required by OVMF), you have to use -drive
if=pflash,unit=0,... and optionally -drive if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, it creates two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
Mapping -drive if=none,... to -blockdev is a solved problem. With
if=T other than if=none, -drive additionally configures a block device
frontend. For non-onboard devices, that part maps to -device. Also a
solved problem. For onboard devices such as PC flash memory, we have
an unsolved problem.
This is actually an instance of a wider problem: our general device
configuration interface doesn't cover onboard devices. Instead, we have
a zoo of ad hoc interfaces that are much more limited. One of them is
-drive, which we'd rather deprecate, but can't until we have suitable
replacements for all its uses.
Sadly, I can't attack the wider problem today. So back to the narrow
problem.
My first idea was to reduce it to its solved buddy by using pluggable
instead of onboard devices for the flash memory. Workable, but it
requires some extra smarts in firmware descriptors and libvirt. Paolo
had an idea that is simpler for libvirt: keep the devices onboard, and
add machine properties for their block backends.
The implementation is less than straightforward, I'm afraid.
First, block backend properties are *qdev* properties. Machines can't
have those, as they're not devices. I could duplicate these qdev
properties as QOM properties, but I hate that.
More seriously, the properties do not belong to the machine, they
belong to the onboard flash devices. Adding them to the machine would
then require bad magic to somehow transfer them to the flash devices.
Fortunately, QOM provides the means to handle exactly this case: add
alias properties to the machine that forward to the onboard devices'
properties.
Properties need to be created in .instance_init() methods. For PC
machines, that's pc_machine_initfn(). To make alias properties work,
we need to create the onboard flash devices there, too. Requires
several bug fixes, in the previous commits. We also have to realize
the devices. More on that below.
If the user sets pflash0, firmware resides in flash memory.
pc_system_firmware_init() maps and realizes the flash devices.
Else, firmware resides in ROM. The onboard flash devices aren't used
then. pc_system_firmware_init() destroys them unrealized, along with
the alias properties.
The existing code to pick up drives defined with -drive if=pflash is
replaced by code to desugar into the machine properties.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <87ftrtux81.fsf@dusky.pond.sub.org>
pc_system_firmware_init() parameter @isapc_ram_fw is PCMachineState
member pci_enabled negated. The next commit will need more of
PCMachineState. To prepare for that, pass a PCMachineState *, and
drop the now redundant parameter @isapc_ram_fw.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-11-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This structure is not used since commit 6dd2a5c98a.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308131445.17502-10-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Add an helper to access the opaque struct PFlashCFI01.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-9-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
The first call of sysbus_get_default() creates the main system bus and
stores it in QOM as "/machine/unattached/sysbus". This must not
happen before main() creates "/machine", or else container_get() would
"helpfully" create it as "container" object, and the real creation of
"/machine" would later abort with "attempt to add duplicate property
'machine' to object (type 'container')". Has been that way ever since
we wired up busses in QOM (commit f968fc6892, v1.2.0).
I believe the bug is latent. I got it to bite by trying to
qdev_create() a sysbus device from a machine's .instance_init()
method.
The fix is obvious: store the main system bus in QOM right after
creating "/machine".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190308131445.17502-5-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
See the previous commit for rationale.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308131445.17502-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Compatibility properties started life as a qdev property thing: we
supported them only for qdev properties, and implemented them with the
machinery backing command line option -global.
Recent commit fa0cb34d22 put them to use (tacitly) with memory
backend objects (subtypes of TYPE_MEMORY_BACKEND). To make that
possible, we first moved the work of applying them from the -global
machinery into TYPE_DEVICE's .instance_post_init() method
device_post_init(), in commits ea9ce8934c and b66bbee39f, then made
it available to TYPE_MEMORY_BACKEND's .instance_post_init() method
host_memory_backend_post_init() as object_apply_compat_props(), in
commit 1c3994f6d2.
Note the code smell: we now have function name starting with object_
in hw/core/qdev.c. It has to be there rather than in qom/, because it
calls qdev_get_machine() to find the current accelerator's and
machine's compat_props.
Turns out calling qdev_get_machine() there is problematic. If we
qdev_create() from a machine's .instance_init() method, we call
device_post_init() and thus qdev_get_machine() before main() can
create "/machine" in QOM. qdev_get_machine() tries to get it with
container_get(), which "helpfully" creates it as "container" object,
and returns that. object_apply_compat_props() tries to paper over the
problem by doing nothing when the value of qdev_get_machine() isn't a
TYPE_MACHINE. But the damage is done already: when main() later
attempts to create the real "/machine", it fails with "attempt to add
duplicate property 'machine' to object (type 'container')", and
aborts.
Since no machine .instance_init() calls qdev_create() so far, the bug
is latent. But since I want to do that, I get to fix the bug first.
Observe that object_apply_compat_props() doesn't actually need the
MachineState, only its the compat_props member of its MachineClass and
AccelClass. This permits a simple fix: register MachineClass and
AccelClass compat_props with the object_apply_compat_props() machinery
right after these classes get selected.
This is actually similar to how things worked before commits
ea9ce8934c and b66bbee39f, except we now register much earlier. The
old code registered them only after the machine's .instance_init()
ran, which would've broken compatibility properties for any devices
created there.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190308131445.17502-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
pflash_cfi01_register() takes a size in bytes, a block size in bytes
and a number of blocks. mips_malta_init() passes BIOS_SIZE, 65536,
FLASH_SIZE >> 16. Actually consistent only because BIOS_SIZE (defined
in include/hw/mips/bios.h as (4 * MiB)) matches FLASH_SIZE (defined
locally as 0x400000). Confusing all the same.
Pass FLASH_SIZE instead of BIOS_SIZE.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Aleksandar Rikalo <arikalo@wavecomp.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190308094610.21210-14-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The 'bios_size' variable is only used in the 'if (!kernel_filename &&
!dinfo)' clause. This is the case when we don't provide -pflash command
line option, and also don't provide a -kernel option. In this case we
will check for the -bios option, or use the default BIOS_FILENAME file.
The 'bios' term is valid in this if statement, but is confuse in the
whole mips_malta_init() scope. Restrict his scope.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-13-armbru@redhat.com>
Variable fl_sectors is used just once. Since
fl_sectors = bios_size >> 16 and bios_size = FLASH_SIZE there,
we can simply use FLASH_SIZE >> 16, and eliminate variable.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-12-armbru@redhat.com>
The debug code under DEBUG_BOARD_INIT doesn't compile:
hw/mips/mips_malta.c:1273:16: error: implicit declaration of function ‘blk_name’; did you mean ‘basename’? [-Werror=implicit-function-declaration]
blk_name(dinfo->bdrv), fl_sectors);
^~~~~~~~
hw/mips/mips_malta.c:1273:16: error: nested extern declaration of ‘blk_name’ [-Werror=nested-externs]
hw/mips/mips_malta.c:1273:30: error: ‘DriveInfo’ {aka ‘struct DriveInfo’} has no member named ‘bdrv’
blk_name(dinfo->bdrv), fl_sectors);
^~
Delete it.
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190308094610.21210-11-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
pflash_cfi02_register() takes a size in bytes, a block size in bytes
and a number of blocks. r2d_init() passes FLASH_SIZE, 16 * KiB,
FLASH_SIZE >> 16. Does not compute: size doesn't match block size *
number of blocks. The latter happens to win: FLASH_SIZE / 4,
i.e. 8MiB.
The best information we have on the physical hardware lists a Cypress
S29PL127J60TFI130 128MiBit NOR flash addressable in words of 16 bits,
in sectors of 4 and 32 Kibiwords. We don't model multiple sector
sizes.
Fix the flash size from 8 to 16MiB, and adjust the sector size from 16
to 64KiB. Fix the width from 4 to 2. While there, supply the real
device IDs 0x0001, 0x227e, 0x2220, 0x2200 instead of zeros.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-10-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Machine "ref405ep" maps its flash memory at address 2^32 - image size.
Image size is rounded up to the next multiple of 64KiB. Useless,
because pflash_cfi02_realize() fails with "failed to read the initial
flash content" unless the rounding is a no-op.
If the image size exceeds 0x80000 Bytes, we overlap first SRAM, then
other stuff. No idea how that would play out, but useful outcomes
seem unlikely.
Map the flash memory at fixed address 0xFFF80000 with size 512KiB,
regardless of image size, to match the physical hardware.
Machine "taihu" maps its boot flash memory similarly. The code even
has a comment /* XXX: should check that size is 2MB */, followed by
disabled code to adjust the size to 2MiB regardless of image size.
Its code to map its application flash memory looks the same, except
there the XXX comment asks for 32MiB, and the code to adjust the size
isn't disabled. Note that pflash_cfi02_realize() fails with "failed
to read the initial flash content" for images smaller than 32MiB.
Map the boot flash memory at fixed address 0xFFE00000 with size 2MiB,
to match the physical hardware. Delete dead code from application
flash mapping, and simplify some.
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-9-armbru@redhat.com>
The disabled DEBUG_BOARD_INIT code goes back to the initial commit
1a6c088620, and has since seen only mechanical updates. It sure
feels like useless clutter now. Delete it.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-8-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Machine "sam460ex" maps its flash memory at address 0xFFF00000. When
no image is supplied, its size is 1MiB (0x100000), and 512KiB of ROM
get mapped on top of its second half. Else, it's the size of the
image rounded up to the next multiple of 64KiB.
The rounding is actually useless: pflash_cfi01_realize() fails with
"failed to read the initial flash content" unless it's a no-op.
I have no idea what happens when the pflash's size exceeds 1MiB.
Useful outcomes seem unlikely.
I guess memory at the end of the address space remains unmapped when
it's smaller than 1MiB. Again, useful outcomes seem unlikely.
The physical hardware appears to have 512KiB of flash memory:
https://eu.mouser.com/datasheet/2/268/atmel_AT49BV040B-1180330.pdf
For now, just set the flash memory size to 1MiB regardless of image
size, and document the mess.
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
pflash_cfi01.c and pflash_cfi02.c start their identifiers with
pflash_cfi01_ and pflash_cfi02_ respectively, except for
CFI_PFLASH01(), TYPE_CFI_PFLASH01, CFI_PFLASH02(), TYPE_CFI_PFLASH02.
Rename for consistency.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-5-armbru@redhat.com>
Our implementation of "write to buffer" (command 0xE8) is flawed.
LOG_UNIMP its use, and add some FIXME comments.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-4-armbru@redhat.com>
When a guest tries to abort "write to buffer" (command 0xE8), we print
"PFLASH: Possible BUG - Write block confirm", then exit(1). Letting
the guest terminate QEMU is not a good idea. Instead, LOG_UNIMP we
screwed up, then reset the device.
Macro PFLASH_BUG() is now unused; delete it.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-3-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Kick the display link up event with a 0.1 sec delay,
so the guest has a chance to notice the link down first.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[update for redefined macro]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This allows configure the display resolution which the vgpu should use.
The information will be passed to the guest using EDID, so the mdev
driver must support the vfio edid region for this to work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds EDID support to the vfio display (aka vgpu) code.
When supported by the mdev driver qemu will generate a EDID blob
and pass it on using the new vfio edid region. The EDID blob will
be updated on UI changes (i.e. window resize), so the guest can
adapt.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[remove control flow via macro, use unsigned format specifier]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since commit 578f3c7b08 ("arm: add fw_cfg to "virt" board",
2014-12-22), the machvirt_init() unconditionally creates the
fw_cfg object. Later, commit c30e15658b ("smbios: implement
smbios support for mach-virt", 2015-09-07) added a superfluous
null-check on it.
Remove this superfluous check.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190309181920.30553-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 'boot_splash_filedata_size' was introduced as a global variable
in 3d3b8303c6. This variable is used as a 'size' argument to the
fw_cfg_add_file(). This function has an interface contract with its
'data' argument, but there is no such contract for 'size' (this is
not a referenced pointer). We can simply remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308013222.12524-7-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190218175529.11237-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Code was assigning DFIFO, but didn't return the value to users.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190305195519.24303-6-svens@stackframe.org>
This makes trace logs much easier to read, especially for
people who are not fluent in SCSI.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-5-svens@stackframe.org>
This makes the code easier to read - no functional change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-4-svens@stackframe.org>
This makes the code easier to read - no functional change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-3-svens@stackframe.org>
Instead of using the open-coded versions, use the helper already
present as this makes the code easier to read and less error-prone.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-2-svens@stackframe.org>
Qemu will crash with the assertion error that "assert(r->req.aiocb !=
NULL)" in scsi_read_complete if request is invaild or disk is no medium.
The error is below:
qemu-kvm: hw/scsi/scsi_disk.c:299: scsi_read_complete: Assertion
`r->req.aiocb != NULL' failed.
This patch add a funtion scsi_read_complete_noio to fix it.
Signed-off-by: Zhengui Li <lizhengui@huawei.com>
Message-Id: <1551949966-20092-1-git-send-email-lizhengui@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Kiarie <davidkiarie4@gmail.com>
Message-Id: <20190304151827.1813-2-davidkiarie4@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If SIGP is set, the 'Wait for Reselection' command should jump
immediately to the address stored in the second DWORD of the
instruction. This fixes spurious hangs in the HP-UX 11.11
installer when the SIGP bit gets set by the kernel before the
'Wait for Reselection' command is executed by SCRIPTS.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Helge Deller <deller@gmx.de>
Message-Id: <20190217113717.7077-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HP-UX checks this register after sending data to the target. If there's no valid
information present, it assumes the client disconnected because the kernel sent
to much data. Implement at least some of the SBCL functionality that is possible
without having a real SCSI bus.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190215194021.20543-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Build fails with gcc 9:
CC ppc64-softmmu/hw/scsi/virtio-scsi.o
hw/scsi/virtio-scsi.c: In function ‘virtio_scsi_do_tmf’:
hw/scsi/virtio-scsi.c:265:39: error: taking address of packed member of ‘struct virtio_scsi_ctrl_tmf_req’ may result in an unaligned pointer value [-Werror=address-of-packed-member]
265 | virtio_tswap32s(VIRTIO_DEVICE(s), &req->req.tmf.subtype);
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
All the fields in struct virtio_scsi_ctrl_tmf_req are naturally aligned,
so we could in theory drop QEMU_PACKED. Unfortunately, the header file
is imported from linux which already has the packed attribute. Trying to
fix that in the update-linux-headers.sh script is likely to produce
ugliness. Turn the call to virtio_tswap32s() into an assignment instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155137678223.44753.5438092367451176318.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Processor Trace required CPUID[0x14] but the cpuid_level
have no change when create a kvm guest with
e.g. "-cpu qemu64,+intel-pt".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Message-Id: <1548805979-12321-1-git-send-email-luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some multiboot images could be in the ELF format. In the current
implementation QEMU fails because we try to load these images
as a PVH image.
In order to fix this issue, we should try multiboot first (we
already check the multiboot magic header before to load it).
If it is not a multiboot image, we can try the PVH loader.
Fixes: ab969087da ("pvh: Boot uncompressed kernel using direct boot ABI", 2019-01-15)
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190214180216.246707-1-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-enable PCI_DEVICES for RISC-V.
The patch is based on other <arch>/Kconfig.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: 82a230d5a3 ("riscv-softmmu.mak: replace CONFIG_* with Kconfig "select" directives")
Message-Id: <20190311091256.18385-1-david.abdurachmanov@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_VFIO_PCI was not "default y" - and once you do that, it is also
important to disable it if PCI is not there.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As NVDIMM support is looming for ARM and SPAPR, let's
move the acpi_nvdimm_state to the generic machine struct
instead of duplicating the same code in several machines.
It is also renamed into nvdimms_state and becomes a pointer.
nvdimm and nvdimm-persistence become generic machine options.
They become guarded by a nvdimm_supported machine class member.
We also add a description for those options.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190308182053.5487-3-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As we intend to migrate the acpi_nvdimm_state into
the base machine with a new dimms_state name, let's
also rename the datatype.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308182053.5487-2-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add (partial) emulation of the on-board GPU of the machine. This
allows the PMON2000 firmware to run and should also work with Linux
console but probably not with X yet.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-id: da6370b22e0352ee803d25d68a62ff32eebf06e2.1552152100.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
At least two machines, the PPC mac99 and MIPS fulong2e, have an ATI
gfx chip by default (Rage 128 Pro and M6/RV100 respectively) and
guests running on these and the PMON2000 firmware of the fulong2e
expect this to be available. Fortunately these are very similar chips
so they can be mostly emulated in the same device model. This patch
adds basic emulation of these ATI VGA chips.
While this is incomplete and currently only enough to run the MIPS
firmware and get framebuffer output with Linux, it allows the fulong2e
board to work more like the real hardware and having it in QEMU in
this state provides a way to experiment with it and allows others to
contribute to improve it. It is compiled for all archs but only the
fulong2e (which currently has no display output at all) is set to use
it by default (in a separate patch).
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Tested-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Tested-by: Howard Spoelstra <hsp.cat7@gmail.com>
Message-id: 0b1b7c22873a6e37627261b04fb687412b25ff4f.1552152100.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-4-kraxel@redhat.com
Store reset handler of the parent class and just call that for a
complete virtio reset. When taking the shortcut and calling
virtio_gpu_reset() directly the generic virtio reset code (for
virtqueues etc) will not be executed.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1597621
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-3-kraxel@redhat.com
Needed when VirtioPCIClass subclasses have their own
class struct with some extra fields.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-2-kraxel@redhat.com
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that USB_OHCI was missing (it was brought in via pci.mak,
but r2d needs the sysbus version) and SERIAL is not used.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of hard-coding all config switches in the config file
default-configs/s390x-softmmu.mak, let's use the new Kconfig files
to express the necessary dependencies: The S390_CCW_VIRTIO config switch
for the "s390-ccw-virtio" machine now selects all non-optional devices.
And since we already have the VIRTIO_PCI and VIRTIO_MMIO config switches
for the other two virtio transports, this patch also introduces a new
config switch VIRTIO_CCW for the third, s390x-specific virtio transport,
so that all three virtio transports are now handled in the same way.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Moxie does not use VGA, ISA or RTC, and only has a memory-mapped
serial port. Adjust for the correct dependencies.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that the Dino board uses a memory mapped 16550 UART and
therefore only CONFIG_SERIAL is needed, not CONFIG_SERIAL_ISA.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes it much easier if the users want to disable some of
the embedded machines for their builds.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most of the dependencies are now directly selected by the SAM460EX
switch. We can drop CONFIG_VGA_CIRRUS since this device is already
selected automatically when CONFIG_PCI_DEVICES is set.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it for example easier if the users want to disable
one of the two machines for their builds.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Select the required devices in hw/ppc/Kconfig instead, so that
ppc-softmmu.mak only contains the user-selectable PREP switch.
Plug-in devices like NE2000_ISA are pulled in automatically by the
Kconfig build system now.
Cc: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The POWERNV switch should always select ISA_IPMI_BT, then the other
IPMI options are turned on automatically now.
CONFIG_DIMM should always be selected by the pseries machine,
which in turn depends on CONFIG_MEM_DEVICE since DIMM implements
this interface.
CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak
completely since this device is already automatically enabled via
hw/display/Kconfig now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This automatically removes the TPM backends from the
binary altogether if no front-ends are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
remove default-configs/hyperv.mak and make dependencies
with Kconfig.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-41-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This automatically removes the SCSI subsystem from the
binary altogether if no controllers are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-34-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
let the host controllers select CONFIG_USB and make the devices
default to present whenever USB is available.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on USB' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/usb.mak
followed by adding "select USB" on the host controllers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-33-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is really nothing special in these devices; they are just
ISA devices. Instead of including them for each target,
set CONFIG_ISA_BUS to true, and make the devices default to present
whenever ISA is available. More conversion of ISA devices will
follow.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on ISA_BUS' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/sound.mak
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-32-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make pcie splited from pci and make it configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-30-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-29-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Devices that are mostly used for testing purposes (for example in
endianness-test) will be moved under a new symbol CONFIG_TEST_DEVICES
that can be disabled in the default-configs file. This makes
it easier to drop this code from QEMU if desirable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use CONFIG_EDID to make edid-generate.c and edid-region.c
configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-26-yang.zhong@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VIRTIO_9P || VIRTFS && XEN condition can be computed in hw/Makefile.objs,
removing an "if" from hw/9pfs/Makefile.objs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some functions sometimes uses req->dev even though a local variable
VirtIOBlock* s = req->dev has already been defined.
Updated places to use s everywhere in the file.
Signed-off-by: Anastasiia Rusakova <arusakova917@gmail.com>
Message-id: 20190307161925.4158-1-rusakova.nastasia@icloud.com
Message-Id: <20190307161925.4158-1-rusakova.nastasia@icloud.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With certain USB devices passed through via usb-host, a guest attempting to
reset a usb-host device can trigger a reset loop that renders the USB device
unusable. In my use case, the device was an iPhone XR that was passed through to
a Mac OS X Mojave guest. Upon connecting the device, the following happens:
1) Guest recognizes new device, sends reset to emulated USB host
2) QEMU's USB host sends reset to host kernel
3) Host kernel resets device
4) After reset, host kernel determines that some part of the device descriptor
has changed ("device firmware changed" in dmesg), so host kernel decides to
re-enumerate the device.
5) Re-enumeration causes QEMU to disconnect and reconnect the device in the
guest.
6) goto 1)
Here's from the host kernel (note the "device firmware changed" lines")
[3677704.473050] usb 1-1.3: new high-speed USB device number 53 using ehci-pci
[3677704.555594] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677704.555599] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677704.555602] usb 1-1.3: Product: iPhone
[3677704.555605] usb 1-1.3: Manufacturer: Apple Inc.
[3677704.555607] usb 1-1.3: SerialNumber: [[removed]]
[3677709.401040] usb 1-1.3: reset high-speed USB device number 53 using ehci-pci
[3677709.479486] usb 1-1.3: device firmware changed
[3677709.479842] usb 1-1.3: USB disconnect, device number 53
[3677709.546039] usb 1-1.3: new high-speed USB device number 54 using ehci-pci
[3677709.627471] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677709.627476] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677709.627479] usb 1-1.3: Product: iPhone
[3677709.627481] usb 1-1.3: Manufacturer: Apple Inc.
[3677709.627483] usb 1-1.3: SerialNumber: [[removed]]
[3677762.320044] usb 1-1.3: reset high-speed USB device number 54 using ehci-pci
[3677762.615630] usb 1-1.3: USB disconnect, device number 54
[3677762.787043] usb 1-1.3: new high-speed USB device number 55 using ehci-pci
[3677762.869016] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677762.869024] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677762.869028] usb 1-1.3: Product: iPhone
[3677762.869032] usb 1-1.3: Manufacturer: Apple Inc.
[3677762.869035] usb 1-1.3: SerialNumber: [[removed]]
[3677815.662036] usb 1-1.3: reset high-speed USB device number 55 using ehci-pci
Here's from QEMU:
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/022: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/024: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/026: No such file or directory
The result of this is that the device remains permanently unusable in the guest.
The same problem has been previously reported for an iPad:
https://stackoverflow.com/questions/52617634/how-do-i-get-qemu-usb-passthrough-to-work-for-ipad-iphone
This problem can be elegantly solved by interrupting step 2) above. Instead of
passing through the reset, QEMU simply ignores it. To allow this to be
configured on a per-device level, a new parameter "no_guest_reset" is
introduced for the usb-host device. I can confirm that the configuration
described above (iPhone XS + Mojave guest) works flawlessly with
no_guest_reset=True specified.
Working command line for my scenario:
device_add usb-host,vendorid=0x05ac,productid=0x12a8,no_guest_reset=True,id=iphone
Best regards
Alexander
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190128140027.9448-1-kraxel@redhat.com
[ kraxel: rename parameter to "guest-reset" ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
During a write, free up the "path" before getting more data.
Also, while we at it, remove the confusing usage of d->fd for
storing mkdir status
Spotted by Coverity: CID 1398642
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
MTP writes objects in small chunks and at the end gets the
real file size to update the object metadata. If this fails for
any reason, return an INCOMPLETE_TRANSFER to the initiator
Spotted by Coverity: CID 1398651
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Let's use a wrapper instead of looking it up manually. This function can
than be reused when we explicitly want to have the bus hotplug handler
(e.g. when the bus hotplug handler was overwritten by the machine
hotplug handler).
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-4-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will allow to return another hotplug handler than the default
one for a specific bus based device type. Which is needed to handle
non trivial plug/unplug sequences that need the access to resources
configured outside of bus where device is attached.
That will allow for returned hotplug handler to orchestrate wiring
in arbitrary order, by chaining other hotplug handlers when
it's needed.
PS:
It could be used for hybrid virtio-mem and virtio-pmem devices
where it will return machine as hotplug handler which will do
necessary wiring at machine level and then pass control down
the chain to bus specific hotplug handler.
Example of top level hotplug handler override and custom plug sequence:
some_machine_get_hotplug_handler(machine){
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
return HOTPLUG_HANDLER(machine);
}
return NULL;
}
some_machine_device_plug(hotplug_dev, dev) {
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
/* do machine specific initialization */
some_machine_init_special_device(dev)
/* pass control to bus specific handler */
hotplug_handler_plug(dev->parent_bus->hotplug_handler, dev)
}
}
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-3-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When unplugging a device, at one point the device will be destroyed
via object_unparent(). This will, one the one hand, unrealize the
removed device hierarchy, and on the other hand, destroy/free the
device hierarchy.
When chaining hotplug handlers, we want to overwrite a bus hotplug
handler by the machine hotplug handler, to be able to perform
some part of the plug/unplug and to forward the calls to the bus hotplug
handler.
For now, the bus hotplug handler would trigger an object_unparent(), not
allowing us to perform some unplug action on a device after we forwarded
the call to the bus hotplug handler. The device would be gone at that
point.
machine_unplug_handler(dev)
/* eventually do unplug stuff */
bus_unplug_handler(dev)
/* dev is gone, we can't do more unplug stuff */
So move the object_unparent() to the original caller of the unplug. For
now, keep the unrealize() at the original places of the
object_unparent(). For implicitly chained hotplug handlers (e.g. pc
code calling acpi hotplug handlers), the object_unparent() has to be
done by the outermost caller. So when calling hotplug_handler_unplug()
from inside an unplug handler, nothing is to be done.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> calls unrealize(dev)
/* we can do more unplug stuff but device already unrealized */
}
object_unparent(dev)
In the long run, every unplug action should be factored out of the
unrealize() function into the unplug handler (especially for PCI). Then
we can get rid of the additonal unrealize() calls and object_unparent()
will properly unrealize the device hierarchy after the device has been
unplugged.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> only unplugs, does not unrealize
/* we can do more unplug stuff */
}
object_unparent(dev) -> will unrealize
The original approach was suggested by Igor Mammedov for the PCI
part, but I extended it to all hotplug handlers. I consider this one
step into the right direction.
To summarize:
- object_unparent() on synchronous unplugs is done by common code
-- "Caller of hotplug_handler_unplug"
- object_unparent() on asynchronous unplugs ("unplug requests") has to
be done manually
-- "Caller of hotplug_handler_unplug"
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-2-david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The qbus_is_full(BusState *bus) function (qdev_monitor.c) compares the max_index
value of the BusState structure with the max_dev value of the BusClass structure
to determine whether the maximum number of children has been reached for the
bus. The problem is, the max_index field of the BusState structure does not
necessarily reflect the number of devices that have been plugged into
the bus.
Whenever a child device is plugged into the bus, the bus's max_index value is
assigned to the child device and then incremented. If the child is subsequently
unplugged, the value of the max_index does not change and no longer reflects the
number of children.
When the bus's max_index value reaches the maximum number of devices
allowed for the bus (i.e., the max_dev field in the BusClass structure),
attempts to plug another device will be rejected claiming that the bus is
full -- even if the bus is actually empty.
To resolve the problem, a new 'num_children' field is being added to the
BusState structure to keep track of the number of children plugged into the
bus. It will be incremented when a child is plugged, and decremented when a
child is unplugged.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <1545062250-7573-1-git-send-email-akrowiak@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
-----BEGIN PGP SIGNATURE-----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=dk89
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20190306a' into staging
Migation pull 2019-03-06
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
# gpg: Signature made Wed 06 Mar 2019 11:39:53 GMT
# gpg: using RSA key 0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20190306a: (22 commits)
qapi/migration.json: Remove a variable that doesn't exist in example
Migration/colo.c: Make COLO node running after failover
Migration/colo.c: Fix double close bug when occur COLO failover
virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT
migration/ram.c: add the free page optimization enable flag
migration/ram.c: add a notifier chain for precopy
migration: API to clear bits of guest free pages from the dirty bitmap
migration: use bitmap_mutex in migration_bitmap_clear_dirty
bitmap: bitmap_count_one_with_offset
bitmap: fix bitmap_count_one
tests: Add basic migration precopy tcp test
migration: Create socket-address parameter
tests: Add migration xbzrle test
migration: Add capabilities validation
tests/migration-test: Add a test for ignore-shared capability
migration: Add an ability to ignore shared RAM blocks
migration: Introduce ignore-shared capability
exec: Change RAMBlockIterFunc definition
migration/rdma: clang compilation fix
migration: Cleanup during exit
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new feature enables the virtio-balloon device to receive hints of
guest free pages from the free page vq.
A notifier is registered to the migration precopy notifier chain. The
notifier calls free_page_start after the migration thread syncs the dirty
bitmap, so that the free page optimization starts to clear bits of free
pages from the bitmap. It calls the free_page_stop before the migration
thread syncs the bitmap, which is the end of the current round of ram
save. The free_page_stop is also called to stop the optimization in the
case when there is an error occurred in the process of ram saving.
Note: balloon will report pages which were free at the time of this call.
As the reporting happens asynchronously, dirty bit logging must be
enabled before this free_page_start call is made. Guest reporting must be
disabled before the migration dirty bitmap is synchronized.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Peter Xu <peterx@redhat.com>
Message-Id: <1544516693-5395-8-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Dropped kernel header update, fixed up CMD_ID_* name change
Don't dynamically allocate the pflash's timer. But do use timer_del in
an unrealize function to make sure that the timer can't fire after the
pflash_t has been freed.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190219153727.62279-1-stephen.checkoway@oberlin.edu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
acpi_table_builtin is now always false, it is not necessary to check it
again.
This patch just removes it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190214084939.20640-4-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Function acpi_table_add_builtin() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190214084939.20640-3-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Function pc_acpi_init() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190214084939.20640-2-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have the extended memory map (high IO regions beyond the
scalable RAM) and dynamic IPA range support at KVM/ARM level
we can bump the legacy 255GB initial RAM limit. The actual maximum
RAM size now depends on the physical CPU and host kernel, in
accelerated mode. In TCG mode, it depends on the VCPU
AA64MMFR0.PARANGE.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are about to allow the memory map to grow beyond 1TB and
potentially overshoot the VCPU AA64MMFR0.PARANGE.
In aarch64 mode and when highmem is set, let's check the VCPU
PA range is sufficient to address the highest GPA of the memory
map.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the machine class kvm_type() callback.
It returns the number of bits requested to implement the whole GPA
range including the RAM and IO regions located beyond.
The returned value is passed though the KVM_CREATE_VM ioctl and
this allows KVM to set the stage2 tables dynamically.
To compute the highest GPA used in the memory map, kvm_type()
must freeze the memory map by calling virt_set_memmap().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-9-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On ARM, the kvm_type will be resolved by querying the KVMState.
Let's add the MachineState handle to the callback so that we
can retrieve the KVMState handle. in kvm_init, when the callback
is called, the kvm_state variable is not yet set.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-5-eric.auger@redhat.com
[ppc parts]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We introduce an helper to create a memory node.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190304101339.25970-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Expose the virtio-net self announcement capability and allow
qemu_announce_self() to call it.
These announces are caused by something external (i.e. the
announce-self command); they won't trigger if the migration
counter is triggering announces at the same time.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Switch virtio's self announcement to use the AnnounceTimer.
It keeps it's own AnnounceTimer (per device), and starts running it
using a migration post-load and a virtual clock; that way the
announce happens once the guest is actually running.
The timer uses the migration parameters to set the timing of
the repeats.
Based on earlier patches by myself and
Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcdAQoAAoJEHWtZYAqC0IRuX4IAIIcHthcKTpBWl144gyXxh0i
o/yjf6eYdmy75blaRsEF7UjNiY5C6/EXbw8nX8mTAGtspAL5Tj1BXWgYVuQ02C6e
qdsN0Pcy6kVuqeCwE/6NjSWZCD7pdKA0EiB3H3tBgUEzmjXa6iHz8SlvpQwJQqAB
K0ItBPXnvggu5IZHxqNFOiZowBCNLmNSN7K3cZCUiHoeVa89t2FxykjeASQmmyUP
4vI/6qnLEOFLdvfPcfNBMtlXQII45w0xtB9QwTrn6in1alkPuzVxOcj7UZ0as5IV
/rsAjo3F6UF7oasYlnlwu3l3HYTaaGsJl23F2oUnHZkMtodFcOHKfIgPsXLnKgo=
=UgWQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2019-02-25-1' into staging
Merge tpm 2029/02/25 v1
# gpg: Signature made Mon 25 Feb 2019 15:05:12 GMT
# gpg: using RSA key 75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2019-02-25-1:
tpm_tis: convert tpm_tis_show_buffer() to use trace event
tpm_tis: fix loop that cancels any seizure by a lower locality
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccBqMAAoJECgfDbjSjVRpvSEIAKYPRNdCBX/SSS/L/tmJS5Zt
8IyU/HW1YJ249vO+aT6z4Q3QPgqNC3KjXC3brx/WRoPZnRroen4rv2Kqnk6SayPa
a52d2ubXKWxb3swdG1CAVzFRhq/ABpgAPx0dr1JW+RXgo2lxpJ4GNYxKMosQTaPE
hRNeXl1XlcIK525kJhFH3Hlij9mTRuY6T7ydpPQd8dUq2dBRaL9RrzZRrkZxCy6l
gQPUqNzPhG0XXyOiJmwYyVX0zGzbYrMLrMQAor2SBIYmU+zv2eZGPJUYxoMTUMzt
YR0WCpvkvPITlAryaBoozAIDYVz8PxBRT1KRwpDal+2rzlm6o+veKDiF8R46gn0=
=GzUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, tests
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 22 Feb 2019 15:51:40 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
pci: Sanity test minimum downstream LNKSTA
hw/smbios: fix offset of type 3 sku field
pci: Move NVIDIA vendor id to the rest of ids
virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size
virtio-balloon: Use ram_block_discard_range() instead of raw madvise()
virtio-balloon: Rework ballon_page() interface
virtio-balloon: Corrections to address verification
virtio-balloon: Remove unnecessary MADV_WILLNEED on deflate
i386/kvm: ignore masked irqs when update msi routes
contrib/vhost-user-blk: fix the compilation issue
Revert "contrib/vhost-user-blk: fix the compilation issue"
pc-dimm: use same mechanism for [get|set]_addr
tests/data: introduce "uefi-boot-images" with the "bios-tables-test" ISOs
tests/uefi-test-tools: add build scripts
tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app
roms: build the EfiRom utility from the roms/edk2 submodule
roms: add the edk2 project as a git submodule
vhost-user-test: create a temporary directory per TestServer
vhost-user-test: small changes to init_hugepagefs
vhost-user-test: create a main loop per TestServer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduces hot plug/unplug support for the vfio-ap device.
To hot plug a vfio-ap device using the QEMU device_add command:
(qemu) device_add vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
to which AP resources to be used by the guest have been assigned.
A vfio-ap device can be hot plugged only if:
1. A vfio-ap device has not been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
To hot unplug a vfio-ap device using the QEMU device_del command:
(qemu) device_del vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
specified when the vfio-ap device was attached to the virtual machine's
ap-bus.
A vfio-ap device can be hot unplugged only if:
1. A vfio-ap device has been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
Please note that a hot plug handler is not necessary for the vfio-ap device
because the AP matrix configuration for the guest is performed by the
kernel device driver when the vfio-ap device is realized. The vfio-ap device
represents a VFIO mediated device created in the host sysfs for use by a guest.
The mdev device is configured with an AP matrix (i.e., adapters and domains) via
its sysfs attribute interfaces prior to starting the guest or plugging a vfio-ap
device in. When the device is realized, a file descriptor is opened on the mdev
device which results in a callback to the vfio_ap kernel device driver. The
device driver then configures the AP matrix in the guest's SIE state description
from the AP matrix assigned via the mdev device's sysfs interfaces. The AP
devices will be created for the guest when the AP bus running on the guest
subsequently performs its periodic scan for AP devices.
The qdev_simple_device_unplug_cb() callback function is used for the same
reaons; namely, the vfio_ap kernel device driver will perform the AP resource
de-configuration for the guest when the vfio-ap device is unplugged. When the
vfio-ap device is unrealized, the mdev device file descriptor is closed which
results in a callback to the vfio_ap kernel device driver. The device driver
then clears the AP matrix configuration in the guest's SIE state description
and resets all of the affected queues. The AP devices created for the guest
will be removed when the AP bus running on the guest subsequently performs
its periodic scan and finds there are no longer any AP resources assigned to the
guest.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1550519397-25359-2-git-send-email-akrowiak@linux.ibm.com>
[CH: adapt to changed qbus_set_hotplug_handler() signature]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Re-enable the guest-agent test
- Add the possibility to load a bios image on the mcf5208evb machine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Lzgr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-02-28' into staging
- Updates to MAINTAINERS file
- Re-enable the guest-agent test
- Add the possibility to load a bios image on the mcf5208evb machine
# gpg: Signature made Thu 28 Feb 2019 12:23:25 GMT
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-02-28:
hw/m68k/mcf5208: Support loading of bios images
tests/test-qga: Reenable guest-agent qtest
MAINTAINERS: Clean up the RISC-V TCG backend section
MAINTAINERS: Add some missing entries for the sun4m machine
MAINTAINERS: Add maintainer to the TCG/i386 subsystem
MAINTAINERS: Add maintainers to the Linux subsystem
MAINTAINERS: Orphanize the 'GDB stub' subsystem
MAINTAINERS: Add maintainer to the POSIX subsystem
MAINTAINERS: Add an entry for the Dino machine
MAINTAINERS: Add missing test entries to the Cryptography section
MAINTAINERS: Add missing entries for the QObject section
MAINTAINERS: Add missing entries for the PC machines
MAINTAINERS: Add missing entries for the sun4u machines
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
-----BEGIN PGP SIGNATURE-----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=7MnB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190228-1' into staging
target-arm queue:
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
# gpg: Signature made Thu 28 Feb 2019 11:06:55 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190228-1:
linux-user: Enable HWCAP_ASIMDFHM, HWCAP_JSCVT
target/arm: Enable ARMv8.2-FHM for -cpu max
target/arm: Implement VFMAL and VFMSL for aarch32
target/arm: Implement FMLAL and FMLSL for aarch64
target/arm: Add helpers for FMLAL
Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
target/arm: Gate "miscellaneous FP" insns by ID register field
target/arm: Use MVFR1 feature bits to gate A32/T32 FP16 instructions
hw/arm/armsse: Unify init-svtor and cpuwait handling
hw/arm/iotkit-sysctl: Implement CPUWAIT and INITSVTOR*
hw/arm/iotkit-sysctl: Add SSE-200 registers
hw/misc/iotkit-sysctl: Correct typo in INITSVTOR0 register name
target/arm/arm-powerctl: Add new arm_set_cpu_on_and_reset()
target/arm/cpu: Allow init-svtor property to be set after realize
hw/arm/armsse: Wire up the MHUs
hw/misc/armsse-mhu.c: Model the SSE-200 Message Handling Unit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
