The SCSI bus should remain in the message out phase after the SATN and stop
command rather than transitioning to the command phase. A new ESPState variable
cmdbuf_cdb_offset is added which stores the offset of the CDB from the start
of cmdbuf when accumulating extended message out phase data.
Currently any extended message out data is discarded in do_cmd() before the CDB
is processed in do_busid_cmd().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-38-mark.cave-ayland@ilande.co.uk>
Some guests use a mixture of DMA and non-DMA transfers in combination with the
SATN and stop command to transfer message out phase and command phase bytes to
the target. Prepare for the next commit by adding a maxlen parameter to
get_cmd() to allow partial transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-37-mark.cave-ayland@ilande.co.uk>
This matches the description in the datasheet and is required as support for
non-DMA transfers is added.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-36-mark.cave-ayland@ilande.co.uk>
Commit ea84a44250 "scsi: esp: Defer command completion until previous interrupts
have been handled" provided a mechanism to delay the command completion interrupt
until ESP_RINTR is read after the command has completed.
With the previous fixes for latching the ESP_RINTR bits and deferring the setting
of the command completion interrupt for incoming data to the SCSI callback, this
workaround is no longer required and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-35-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM issues a command to the ESP controller as part of its
"FAST" SCSI routines and then proceeds to read the incoming data soon after
receiving the command completion interrupt.
Unfortunately due to SCSI block transfers being asynchronous the incoming data
may not yet be present causing an underflow error. Resolve this by waiting for
the SCSI subsystem transfer_data callback before raising the command completion
interrupt.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-34-mark.cave-ayland@ilande.co.uk>
Currently the ESP_RINTR register is set to a specific value as required within
the ESP state machine. In order to implement the upcoming deferred interrupt
functionality it is necessary to set individual bits within ESP_RINTR so that
a deferred interrupt will not overwrite the value of any other interrupt bits.
This also requires fixing up a few locations where the ESP_RINTR and ESP_RSEQ
registers are set/reset unexpectedly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-33-mark.cave-ayland@ilande.co.uk>
At this point it is now possible to properly implement the FIFO flush command
without causing guest errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-32-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM performs 4 byte reads/writes when transferring data to
and from the target. Since the SCSI bus is 16-bits wide, use the memory API
to split a 4 byte access into 2 x 2 byte accesses.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-31-mark.cave-ayland@ilande.co.uk>
Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
PDMA as implemented on the Quadra 800 uses DREQ to load data into the FIFO
up to a maximum of 16 bytes at a time. The MacOS toolbox ROM requires this
because it mixes FIFO and PDMA transfers whilst checking the FIFO status
and counter registers to ensure success.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-29-mark.cave-ayland@ilande.co.uk>
Currently the target selection for PDMA is done after the SCSI command has been
delivered which is not correct. Perform target selection as part of the initial
get_cmd() call when the command is submitted: if no target is present, don't
raise DRQ.
If the target is present then switch to the command phase since the MacOS toolbox
ROM checks for this before attempting to submit the SCSI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-28-mark.cave-ayland@ilande.co.uk>
This better describes the purpose of the function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-27-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Here the updates to async_len and ti_size are moved into the corresponding
esp_pdma_read()/esp_pdma_write() function to eliminate the reference to
pdma_cur in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-23-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf and buflen
parameters from get_cmd() since these always reference cmdbuf and ESP_CMDBUF_SZ
respectively.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-21-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf parameter
from do_cmd() since this always points to cmdbuf.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-20-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fixes: 74d71ea16b
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200218094402.26625-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There is no DMA in Quadra 800, so the CPU reads/writes the data from the
PDMA register (offset 0x100, ESP_PDMA in hw/m68k/q800.c) and copies them
to/from the memory.
There is a nice assembly loop in the kernel to do that, see
linux/drivers/scsi/mac_esp.c:MAC_ESP_PDMA_LOOP().
The start of the transfer is triggered by the DREQ interrupt (see linux
mac_esp_send_pdma_cmd()), the CPU polls on the IRQ flag to start the
transfer after a SCSI command has been sent (in Quadra 800 it goes
through the VIA2, the via2-irq line and the vIFR register)
The Macintosh hardware includes hardware handshaking to prevent the CPU
from reading invalid data or writing data faster than the peripheral
device can accept it.
This is the "blind mode", and from the doc:
"Approximate maximum SCSI transfer rates within a blocks are 1.4 MB per
second for blind transfers in the Macintosh II"
Some references can be found in:
Apple Macintosh Family Hardware Reference, ISBN 0-201-19255-1
Guide to the Macintosh Family Hardware, ISBN-0-201-52405-8
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-4-laurent@vivier.eu>
This will be needed to implement pseudo-DMA
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-3-laurent@vivier.eu>
To prepare following patches move do_cmd and DMA special case
from handle_ti() to esp_do_dma().
This part of the code must be only executed with real DMA, not with
pseudo-DMA. And PDMA is detected in esp_do_dma(), so move this part
of the code in esp_do_dma(). We keep the code in handle_ti_cmd()
in the case no DMA is done.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-2-laurent@vivier.eu>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
This enables them to be used outside of esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
SunOS defines ESP (x86 register) in <sys/regset.h> as 7.
This fixes build on SmartOS (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Message-Id: <20170909142116.26816-1-n54@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
This fixes SCSI adapter self-tests done in MIPS Jazz emulation,
broken since ff589551c8.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1479508397-8443-1-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 926cde5 ("scsi: esp: make cmdbuf big enough for maximum CDB size",
2016-06-16) changed the size of a migrated field. Split it in two
parts, and only migrate the second part in a new vmstate version.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While doing DMA read into ESP command buffer 's->cmdbuf', it could
write past the 's->cmdbuf' area, if it was transferring more than 16
bytes. Increase the command buffer size to 32, which is maximum when
's->do_cmd' is set, and add a check on 'len' to avoid OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid duplicated code between esp_do_dma and handle_ti. esp_do_dma
has the same code that handle_ti contains after the call to esp_do_dma;
but the code in handle_ti is never reached because it is in an "else if".
Remove the else and also the pointless return.
esp_do_dma also has a partially dead assignment of the to_device
variable. Sink it to the point where it's actually used.
Finally, assert that the other caller of esp_do_dma (esp_transfer_data)
only transfers data and not a command. This is true because get_cmd
cancels the old request synchronously before its caller handle_satn_stop
sets do_cmd to 1.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer.
Routine get_cmd() in non-DMA mode, uses 'ti_size' to read scsi
command into a buffer. Add check to validate command length against
buffer size to avoid any overrun.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464717207-7549-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with internal 16-byte
FIFO buffers. One is used to handle commands and other is for
information transfer. Three control variables 'ti_rptr',
'ti_wptr' and 'ti_size' are used to control r/w access to the
information transfer buffer ti_buf[TI_BUFSZ=16]. In that,
'ti_rptr' is used as read index, where read occurs.
'ti_wptr' is a write index, where write would occur.
'ti_size' indicates total bytes to be read from the buffer.
While reading/writing to this buffer, index could exceed its
size. Add check to avoid OOB r/w access.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1465230883-22303-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer.
Routine get_cmd() uses DMA to read scsi commands into this buffer.
Add check to validate DMA length against buffer size to avoid any
overrun.
Fixes CVE-2016-4441.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1463654371-11169-3-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer. While
writing to this command buffer 's->cmdbuf[TI_BUFSZ=16]', a check
was missing to validate input length. Add check to avoid OOB write
access.
Fixes CVE-2016-4439.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1463654371-11169-2-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-24-git-send-email-peter.maydell@linaro.org
After a reset ESP_TCHI should contain the unique ID
of the chip. This value will be overwritten with the
current tranfer count if the transfer count has
previously been set.
So we should always return the chip id if ESP_TCHI
has never been written to.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
To be passed to qbus_create_inplace().
Use DEVICE() casts instead of direct parent field access.
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Let scsi_bus_legacy_add_drive() and scsi_bus_legacy_handle_cmdline()
return an Error**. Prepare qdev initfns for QOM realize error model.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and avoid DO_UPCAST().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds the possibility to create a scsi-bus with a specified name.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1367330931-12994-4-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
