Remove an unnecessary le_to_cpu conversion in Identify.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
ZASL (Zone Append Size Limit) is defined exactly like MDTS (Maximum Data
Transfer Size), that is, it is a value in units of the minimum memory
page size (CAP.MPSMIN) and is reported as a power of two.
The 'mdts' nvme device parameter is specified as in the spec, but the
'zoned.append_size_limit' parameter is specified in bytes. This is
suboptimal for a number of reasons:
1. It is just plain confusing wrt. the definition of mdts.
2. There is a lot of complexity involved in validating the value; it
must be a power of two, it should be larger than 4k, if it is zero
we set it internally to mdts, but still report it as zero.
3. While "hw/block/nvme: improve invalid zasl value reporting"
slightly improved the handling of the parameter, the validation is
still wrong; it does not depend on CC.MPS, it depends on
CAP.MPSMIN. And we are not even checking that it is actually less
than or equal to MDTS, which is kinda the *one* condition it must
satisfy.
Fix this by defining zasl exactly like mdts and checking the one thing
that it must satisfy (that it is less than or equal to mdts). Also,
change the default value from 128KiB to 0 (aka, whatever mdts is).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 6eb7a07129 ("hw/block/nvme: change controller pci id") changed
the controller to use a Red Hat assigned PCI Device and Vendor ID, but
did not change the IEEE OUI away from the Intel IEEE OUI.
Fix that and use the locally assigned QEMU IEEE OUI instead if the
`use-intel-id` parameter is not explicitly set. Also reverse the Intel
IEEE OUI bytes.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Zone Append Size Limit (ZASL) must be at least 4096 bytes, so
improve the user experience by adding an early parameter check in
nvme_check_constraints.
When ZASL is still too small due to the host configuring the device for
an even larger page size, convert the trace point in nvme_start_ctrl to
an NVME_GUEST_ERR such that this is logged by QEMU instead of only
traced.
Reported-by: Corne <info@dantalion.nl>
Cc: Dmitry Fomichev <Dmitry.Fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Firstly, if zoned.max_active is non-zero, zoned.max_open must be less
than or equal to zoned.max_active.
Secondly, if only zones.max_active is set, we have to explicitly set
zones.max_open or we end up with an invalid MAR/MOR configuration. This
is an artifact of the parameters not being zeroes-based like in the
spec.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reported-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and Explicitly Open zones can be closed by Close Zone
management function. This got broken by a recent commit ("hw/block/nvme:
refactor zone resource management") and now such commands fail with
Invalid Zone State Transition status.
Modify nvm_zrm_close() function to make Close Zone work correctly.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for TP 4065a ("Simple Copy Command"), v2020.05.04
("Ratified").
The implementation uses a bounce buffer to first read in the source
logical blocks, then issue a write of that bounce buffer. The default
maximum number of source logical blocks is 128, translating to 512 KiB
for 4k logical blocks which aligns with the default value of MDTS.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
In preparation for Simple Copy, pull write pointer advancement into a
separate function that is independent off an NvmeRequest.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Zone transition handling and resource management is open coded (and
semi-duplicated in the case of open, close and finish).
In preparation for Simple Copy command support (which also needs to open
zones for writing), consolidate into a set of 'nvme_zrm' functions and
in the process fix a bug with the controller not closing an open zone to
allow another zone to be explicitly opened.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Remove the unused NvmeCtrl parameter in nvme_check_zone_write.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
nvme-ns device is registered to a nvme controller device during the
initialization in nvme_register_namespace() in case that 'bus' property
is given which means it's mapped to a single controller.
This patch introduced a new property 'subsys' just like the controller
device instance did to map a namespace to a NVMe subsystem.
If 'subsys' property is given to the nvme-ns device, it will belong to
the specified subsystem and will be attached to all controllers in that
subsystem by enabling shared namespace capability in NMIC(Namespace
Multi-path I/O and Namespace Capabilities) in Identify Namespace.
Usage:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme,serial=bar,id=nvme1,subsys=subsys0
-device nvme,serial=baz,id=nvme2,subsys=subsys0
-device nvme-ns,id=ns1,drive=<drv>,nsid=1,subsys=subsys0 # Shared
-device nvme-ns,id=ns2,drive=<drv>,nsid=2,bus=nvme2 # Non-shared
In the above example, 'ns1' will be shared to 'nvme0' and 'nvme1' in
the same subsystem. On the other hand, 'ns2' will be attached to the
'nvme2' only as a private namespace in that subsystem.
All the namespace with 'subsys' parameter will attach all controllers in
the subsystem to the namespace by default.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
We have nvme-subsys and nvme devices mapped together. To support
multi-controller scheme to this setup, controller identifier(id) has to
be managed. Earlier, cntlid(controller id) used to be always 0 because
we didn't have any subsystem scheme that controller id matters.
This patch introduced 'cntlid' attribute to the nvme controller
instance(NvmeCtrl) and make it allocated by the nvme-subsys device
mapped to the controller. If nvme-subsys is not given to the
controller, then it will always be 0 as it was.
Added 'ctrls' array in the nvme-subsys instance to manage attached
controllers to the subsystem with a limit(32). This patch didn't take
list for the controllers to make it seamless with nvme-ns device.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme controller(nvme) can be mapped to a NVMe subsystem(nvme-subsys).
This patch maps a controller to a subsystem by adding a parameter
'subsys' to the nvme device.
To map a controller to a subsystem, we need to put nvme-subsys first and
then maps the subsystem to the controller:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
If 'subsys' property is not given to the nvme controller, then subsystem
NQN will be created with serial (e.g., 'foo' in above example),
Otherwise, it will be based on subsys id (e.g., 'subsys0' in above
example).
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
To support multi-path in QEMU NVMe device model, We need to have NVMe
subsystem hierarchy to map controllers and namespaces to a NVMe
subsystem.
This patch introduced a simple nvme-subsys device model. The subsystem
will be prepared with subsystem NQN with <subsys_id> provided in
nvme-subsys device:
ex) -device nvme-subsys,id=subsys0: nqn.2019-08.org.qemu:subsys0
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: added 'nqn' device parameter per request]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
-----BEGIN PGP SIGNATURE-----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=nphT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210308' into staging
target-arm queue:
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
# gpg: Signature made Mon 08 Mar 2021 11:56:24 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210308: (49 commits)
hw/arm/mps2: Update old infocenter.arm.com URLs
docs/system/arm/mps2.rst: Document the new mps3-an524 board
hw/arm/mps2-tz: Provide PL031 RTC on mps3-an524
hw/arm/mps2-tz: Stub out USB controller for mps3-an524
hw/arm/mps2-tz: Add new mps3-an524 board
hw/arm/mps2-tz: Get armv7m_load_kernel() size argument from RAMInfo
hw/arm/mps2-tz: Support ROMs as well as RAMs
hw/arm/mps2-tz: Set MachineClass default_ram info from RAMInfo data
hw/arm/mps2-tz: Make RAM arrangement board-specific
hw/arm/mps2-tz: Allow boards to have different PPCInfo data
hw/arm/mps2-tz: Size the uart-irq-orgate based on the number of UARTs
hw/arm/mps2-tz: Move device IRQ info to data structures
hw/arm/mps2-tz: Allow PPCPortInfo structures to specify device interrupts
hw/arm/mps2-tz: Correct wrong interrupt numbers for DMA and SPI
hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524
hw/arm/mps2-tz: Make number of IRQs board-specific
hw/arm/mps2-tz: Condition IRQ splitting on number of CPUs, not board type
hw/arm/mps2-tz: Make FPGAIO switch and LED config per-board
hw/misc/mps2-fpgaio: Support SWITCH register
hw/misc/mps2-fpgaio: Make number of LEDs configurable by board
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
This file is borrowed from the RTEMS source code, which comes
with a GPL-2.0-or-later license with a header exception.
Expand the GPL-2.0-or-later license in place to not be dependent
on a 3rd party website. This also fix the misleading comment "The
license and distribution terms for this file may be found in the
file LICENSE in this distribution" referring to the RTEMS distribution
and not to the QEMU one.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210222185605.2714192-1-f4bug@amsat.org>
As replaced the generic CONFIG_SH4 by more fine-grained
selectors, we can remove this now unused config variable.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-9-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_PCI selector for the SH4 PCI controller.
Move the file with the other PCI host devices in hw/pci-host
and add its missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-8-f4bug@amsat.org>
Add more fine-grained selection by adding a CONFIG_TC58128
selector for the TC58128 eeprom.
As this device is only used by the Shix machine, add an entry
to the proper section in MAINTAINERS.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-7-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_TIMER selector for the SH4 timer control unit.
Add the missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-6-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_SCI selector for the SH4 serial controller.
Add the missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-5-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_INTC selector for the SH4 interrupt controller.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-4-f4bug@amsat.org>
r2d_init() calls sh7750_init() so depends on SH7750.Harmless
at the moment because nothing actually uses CONFIG_SH7750
(hw/sh4/meson.build always compiles sh7750.c and sh7750_regnames.c
unconditionally).
Fixes: 7ab58d4c84 ("sh4-softmmu.mak: express dependencies with Kconfig")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-3-f4bug@amsat.org>
This code was introduced in commit 27c7ca7e77,
("SHIX board emulation (Samuel Tardieu)"). Use
the same license.
Cc: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-2-f4bug@amsat.org>
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
The AN505 and AN521 don't have any read-only memory, but the AN524
does; add a flag to ROMInfo to mark a region as ROM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-19-peter.maydell@linaro.org
Instead of hardcoding the MachineClass default_ram_size and
default_ram_id fields, set them on class creation by finding the
entry in the RAMInfo array which is marked as being the QEMU system
RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-18-peter.maydell@linaro.org
The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
