d1f6af6 "kvm-irqchip: simplify kvm_irqchip_add_msi_route" was a cleanup
of kvmchip routing configuration, that was mostly intended for x86.
However, it also contains a subtle change in behaviour which breaks EEH[1]
error recovery on certain VFIO passthrough devices on spapr guests. So far
it's only been seen on a BCM5719 NIC on a POWER8 server, but there may be
other hardware with the same problem. It's also possible there could be
circumstances where it causes a bug on x86 as well, though I don't know of
any obvious candidates.
Prior to d1f6af6, both vfio_msix_vector_do_use() and
vfio_add_kvm_msi_virq() used msg == NULL as a special flag to mark this
as the "dummy" vector used to make the host hardware state sync with the
guest expected hardware state in terms of MSI configuration.
Specifically that flag caused vfio_add_kvm_msi_virq() to become a no-op,
meaning the dummy irq would always be delivered via qemu. d1f6af6 changed
vfio_add_kvm_msi_virq() so it takes a vector number instead of the msg
parameter, and determines the correct message itself. The test for !msg
was removed, and not replaced with anything there or in the caller.
With an spapr guest which has a VFIO device, if an EEH error occurs on the
host hardware, then the device will be isolated then reset. This is a
combination of host and guest action, mediated by some EEH related
hypercalls. I haven't fully traced the mechanics, but somehow installing
the kvm irqchip route for the dummy irq on the BCM5719 means that after EEH
reset and recovery, at least some irqs are no longer delivered to the
guest.
In particular, the guest never gets the link up event, and so the NIC is
effectively dead.
[1] EEH (Enhanced Error Handling) is an IBM POWER server specific PCI-*
error reporting and recovery mechanism. The concept is somewhat
similar to PCI-E AER, but the details are different.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1373802
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Gavin Shan <gwshan@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: qemu-stable@nongnu.org
Fixes: d1f6af6a17 ("kvm-irqchip: simplify kvm_irqchip_add_msi_route")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-4-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
In the past, we are doing gsi route commit for each irqchip route
update. This is not efficient if we are updating lots of routes in the
same time. This patch removes the committing phase in
kvm_irqchip_update_msi_route(). Instead, we do explicit commit after all
routes updated.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Changing the original MSIMessage parameter in kvm_irqchip_add_msi_route
into the vector number. Vector index provides more information than the
MSIMessage, we can retrieve the MSIMessage using the vector easily. This
will avoid fetching MSIMessage every time before adding MSI routes.
Meanwhile, the vector info will be used in the coming patches to further
enable gsi route update notifications.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU supports ARI on downstream ports and assigned devices may support
ARI in their extended capabilities. The endpoint ARI capability
specifies the next function, such that the OS doesn't need to walk
each possible function, however this next function is relative to the
host, not the guest. This leads to device discovery issues when we
combine separate functions into virtual multi-function packages in a
guest. For example, SR-IOV VFs are not enumerated by simply probing
the function address space, therefore the ARI next-function field is
zero. When we combine multiple VFs together as a multi-function
device in the guest, the guest OS identifies ARI is enabled, relies on
this next-function field, and stops looking for additional function
after the first is found.
Long term we should expose the ARI capability to the guest to enable
configurations with more than 8 functions per slot, but this requires
additional QEMU PCI infrastructure to manage the next-function field
for multiple, otherwise independent devices. In the short term,
hiding this capability allows equivalent functionality to what we
currently have on non-express chipsets.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
This ioctl() call to VFIO_IOMMU_SPAPR_TCE_REMOVE was left over from an
earlier version of the code and has since been folded into
vfio_spapr_remove_window().
It wasn't caught because although the argument structure has been removed,
the libc function remove() means this didn't trigger a compile failure.
The ioctl() was also almost certain to fail silently and harmlessly with
the bogus argument, so this wasn't caught in testing.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXe4l4AAoJECgfDbjSjVRpIz4IALye7mKG61/POA4Gqmhalc3d
HnlNSZ2YcKAuvPg7WWkBuRacrQvVY/MbW1mLloG1lY0tdFgZG8Cy+CY6wJg1NE4c
cXd+77vHkIyrnl+Nil+QOgTFiAsMnD+mXHHsnCDw2jGn3JbgVNuCMi7V34fGkQd2
PDkZyYfwTqO3HytuG0/j2Somc9du1gjYdn+9qigfZVgP96jGDojBuJWuuU5flCB3
Kj5xrOuI01XlbdTk71tVjBJBektQurWr6r7GECDqZIpUfc+BI70FU9jPh+OlLTO/
92yi29ncjyStz4tRnf18xoQ8uBgH/tD1xigEUPRtnm1+0i/tgONBL8cAdBF9FBE=
=ABGE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Jul 2016 11:18:32 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (30 commits)
vmw_pvscsi: remove unnecessary internal msi state flag
e1000e: remove unnecessary internal msi state flag
vmxnet3: remove unnecessary internal msi state flag
mptsas: remove unnecessary internal msi state flag
megasas: remove unnecessary megasas_use_msi()
pci: Convert msi_init() to Error and fix callers to check it
pci bridge dev: change msi property type
megasas: change msi/msix property type
mptsas: change msi property type
intel-hda: change msi property type
usb xhci: change msi/msix property type
change pvscsi_init_msi() type to void
tests: add APIC.cphp and DSDT.cphp blobs
tests: acpi: add CPU hotplug testcase
log: Permit -dfilter 0..0xffffffffffffffff
range: Replace internal representation of Range
range: Eliminate direct Range member access
log: Clean up misuse of Range for -dfilter
pci_register_bar: cleanup
Revert "virtio-net: unbreak self announcement and guest offloads after migration"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
msi_init() reports errors with error_report(), which is wrong
when it's used in realize().
Fix by converting it to Error.
Fix its callers to handle failure instead of ignoring it.
For those callers who don't handle the failure, it might happen:
when user want msi on, but he doesn't get what he want because of
msi_init fails silently.
cc: Gerd Hoffmann <kraxel@redhat.com>
cc: John Snow <jsnow@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Hannes Reinecke <hare@suse.de>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Alex Williamson <alex.williamson@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
New VFIO_SPAPR_TCE_v2_IOMMU type supports dynamic DMA window management.
This adds ability to VFIO common code to dynamically allocate/remove
DMA windows in the host kernel when new VFIO container is added/removed.
This adds a helper to vfio_listener_region_add which makes
VFIO_IOMMU_SPAPR_TCE_CREATE ioctl and adds just created IOMMU into
the host IOMMU list; the opposite action is taken in
vfio_listener_region_del.
When creating a new window, this uses heuristic to decide on the TCE table
levels number.
This should cause no guest visible change in behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added some casts to prevent printf() warnings on certain targets
where the kernel headers' __u64 doesn't match uint64_t or PRIx64]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are going to be multiple IOMMUs per a container. This moves
the single host IOMMU parameter set to a list of VFIOHostDMAWindow.
This should cause no behavioral change and will be used later by
the SPAPR TCE IOMMU v2 which will also add a vfio_host_win_del() helper.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes use of the new "memory registering" feature. The idea is
to provide the userspace ability to notify the host kernel about pages
which are going to be used for DMA. Having this information, the host
kernel can pin them all once per user process, do locked pages
accounting (once) and not spent time on doing that in real time with
possible failures which cannot be handled nicely in some cases.
This adds a prereg memory listener which listens on address_space_memory
and notifies a VFIO container about memory which needs to be
pinned/unpinned. VFIO MMIO regions (i.e. "skip dump" regions) are skipped.
The feature is only enabled for SPAPR IOMMU v2. The host kernel changes
are required. Since v2 does not need/support VFIO_IOMMU_ENABLE, this does
not call it when v2 is detected and enabled.
This enforces guest RAM blocks to be host page size aligned; however
this is not new as KVM already requires memory slots to be host page
size aligned.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Fix compile error on 32-bit host]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The IOMMU driver may change behavior depending on whether a notifier
client is present. In the case of POWER, this represents a change in
the visibility of the IOTLB, for other drivers such as intel-iommu and
future AMD-Vi emulation, notifier support is not yet enabled and this
provides the opportunity to flag that incompatibility.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[new log & extracted from [PATCH qemu v17 12/12] spapr_iommu, vfio, memory: Notify IOMMU about starting/stopping listening]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The kernel currently exposes the SR-IOV capability as read-only
through vfio-pci. This is sufficient to protect the host kernel, but
has the potential to confuse guests without further virtualization.
In particular, OVMF tries to size the VF BARs and comes up with absurd
results, ending with an assert. There's not much point in adding
virtualization to a read-only capability, so we simply hide it for
now. If the kernel ever enables SR-IOV virtualization, we should
easily be able to test it through VF BAR sizing or explicit flags.
Testing whether we should parse extended capabilities is also pulled
into the function to keep these assumptions in one place.
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For vfio pcie device, we could expose the extended capability on
PCIE bus. due to add a new pcie capability at the tail of the chain,
in order to avoid config space overwritten, we introduce a copy config
for parsing extended caps. and rebuild the pcie extended config space.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic
alloc and consistent functions") converted VFIOPCIDevice.vga to be
dynamically allocted, negating the need for VFIOPCIDevice.has_vga.
Unfortunately not all of the has_vga users were converted, nor was
the field removed from the structure. Correct these oversights.
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Tested-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Fixes: 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic alloc and consistent functions")
Fixes: https://bugs.launchpad.net/qemu/+bug/1591628
Cc: qemu-stable@nongnu.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Every IOMMU has some granularity which MemoryRegionIOMMUOps::translate
uses when translating, however this information is not available outside
the translate context for various checks.
This adds a get_min_page_size callback to MemoryRegionIOMMUOps and
a wrapper for it so IOMMU users (such as VFIO) can know the minimum
actual page size supported by an IOMMU.
As IOMMU MR represents a guest IOMMU, this uses TARGET_PAGE_SIZE
as fallback.
This removes vfio_container_granularity() and uses new helper in
memory_region_iommu_replay() when replaying IOMMU mappings on added
IOMMU memory region.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: Removed an unnecessary calculation]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move all trace-events for files in the hw/vfio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-30-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
vfio_eeh_container_op() is the backend that communicates with
host kernel to support EEH functionality in QEMU. However, the
functon should return the value from host kernel instead of 0
unconditionally.
dwg: Specifically the problem occurs for the handful of EEH
sub-operations which can return a non-zero, non-error result.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: clarification to commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At the moment IOMMU MR only translate to the system memory.
However if some new code changes this, we will need clear indication why
it is not working so here is the check.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since a788f227 "memory: Allow replay of IOMMU mapping notifications"
when new VFIO listener is added, all existing IOMMU mappings are
replayed. However there is a problem that the base address of
an IOMMU memory region (IOMMU MR) is ignored which is not a problem
for the existing user (which is pseries) with its default 32bit DMA
window starting at 0 but it is if there is another DMA window.
This stores the IOMMU's offset_within_address_space and adjusts
the IOVA before calling vfio_dma_map/vfio_dma_unmap.
As the IOMMU notifier expects IOVA offset rather than the absolute
address, this also adjusts IOVA in sPAPR H_PUT_TCE handler before
calling notifier(s).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
7532d3cbf "vfio: Fix 128 bit handling" added support for 64bit IOMMU
memory regions when those are added to VFIO address space; however
removing code cannot cope with these as int128_get64() will fail on
1<<64.
This copies 128bit handling from region_add() to region_del().
Since the only machine type which is actually going to use 64bit IOMMU
is pseries and it never really removes them (instead it will dynamically
add/remove subregions), this should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The IGD OpRegion is enabled automatically when running in legacy mode,
but it can sometimes be useful in universal passthrough mode as well.
Without an OpRegion, output spigots don't work, and even though Intel
doesn't officially support physical outputs in UPT mode, it's a
useful feature. Note that if an OpRegion is enabled but a monitor is
not connected, some graphics features will be disabled in the guest
versus a headless system without an OpRegion, where they would work.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Enable quirks to support SandyBridge and newer IGD devices as primary
VM graphics. This requires new vfio-pci device specific regions added
in kernel v4.6 to expose the IGD OpRegion, the shadow ROM, and config
space access to the PCI host bridge and LPC/ISA bridge. VM firmware
support, SeaBIOS only so far, is also required for reserving memory
regions for IGD specific use. In order to enable this mode, IGD must
be assigned to the VM at PCI bus address 00:02.0, it must have a ROM,
it must be able to enable VGA, it must have or be able to create on
its own an LPC/ISA bridge of the proper type at PCI bus address
00:1f.0 (sorry, not compatible with Q35 yet), and it must have the
above noted vfio-pci kernel features and BIOS. The intention is that
to enable this mode, a user simply needs to assign 00:02.0 from the
host to 00:02.0 in the VM:
-device vfio-pci,host=0000:00:02.0,bus=pci.0,addr=02.0
and everything either happens automatically or it doesn't. In the
case that it doesn't, we leave error reports, but assume the device
will operate in universal passthrough mode (UPT), which doesn't
require any of this, but has a much more narrow window of supported
devices, supported use cases, and supported guest drivers.
When using IGD in this mode, the VM firmware is required to reserve
some VM RAM for the OpRegion (on the order or several 4k pages) and
stolen memory for the GTT (up to 8MB for the latest GPUs). An
additional option, x-igd-gms allows the user to specify some amount
of additional memory (value is number of 32MB chunks up to 512MB) that
is pre-allocated for graphics use. TBH, I don't know of anything that
requires this or makes use of this memory, which is why we don't
allocate any by default, but the specification suggests this is not
actually a valid combination, so the option exists as a workaround.
Please report if it's actually necessary in some environment.
See code comments for further discussion about the actual operation
of the quirks necessary to assign these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Capability probing modifies wmask, which quirks may be interested in
changing themselves. Apply our BAR quirks after the capability scan
to make this possible.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Combine VGA discovery and registration. Quirks can have dependencies
on BARs, so the quirks push out until after we've scanned the BARs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
This function returns success if either we setup the VGA region or
the host vfio doesn't return enough regions to support the VGA index.
This latter case doesn't make any sense. If we're asked to populate
VGA, fail if it doesn't exist and let the caller decide if that's
important.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Given a device specific region type and sub-type, find it. Also
cleanup return point on error in vfio_get_region_info() so that we
always return 0 with a valid pointer or -errno and NULL.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
The sparse mmap capability in a vfio region info allows vfio to tell
us which sub-areas of a region may be mmap'd. Thus rather than
assuming a single mmap covers the entire region and later frobbing it
ourselves for things like the PCI MSI-X vector table, we can read that
directly from vfio.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=DpB8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/awilliam/tags/vfio-update-20160328.0' into staging
VFIO updates 2016-03-28
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
# gpg: Signature made Mon 28 Mar 2016 23:16:52 BST using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg: aka "Alex Williamson <alex@shazbot.org>"
# gpg: aka "Alex Williamson <alwillia@redhat.com>"
# gpg: aka "Alex Williamson <alex.l.williamson@gmail.com>"
* remotes/awilliam/tags/vfio-update-20160328.0:
vfio: convert to 128 bit arithmetic calculations when adding mem regions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vfio_listener_region_add for a iommu mr results in
an overflow assert since iommu memory region is initialized
with UINT64_MAX. Convert calculations to 128 bit arithmetic
for iommu memory regions and let int128_get64 assert for non iommu
regions if there's an overflow.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
[missed (end - 1) on 2nd trace call, move llsize closer to use]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vfio_container_ioctl() was a bad interface that bypassed abstraction
boundaries, had semantics that sat uneasily with its name, and was unsafe
in many realistic circumstances. Now that spapr-pci-vfio-host-bridge has
been folded into spapr-pci-host-bridge, there are no more users, so remove
it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
At present the code handling IBM's Enhanced Error Handling (EEH) interface
on VFIO devices operates by bypassing the usual VFIO logic with
vfio_container_ioctl(). That's a poorly designed interface with unclear
semantics about exactly what can be operated on.
In particular it operates on a single vfio container internally (hence the
name), but takes an address space and group id, from which it deduces the
container in a rather roundabout way. groupids are something that code
outside vfio shouldn't even be aware of.
This patch creates new interfaces for EEH operations. Internally we
have vfio_eeh_container_op() which takes a VFIOContainer object
directly. For external use we have vfio_eeh_as_ok() which determines
if an AddressSpace is usable for EEH (at present this means it has a
single container with exactly one group attached), and vfio_eeh_as_op()
which will perform an operation on an AddressSpace in the unambiguous case,
and otherwise returns an error.
This interface still isn't great, but it's enough of an improvement to
allow a number of cleanups in other places.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Devices like Intel graphics are known to not only have bad checksums,
but also the wrong device ID. This is not so surprising given that
the video BIOS is typically part of the system firmware image rather
that embedded into the device and needs to support any IGD device
installed into the system.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Match common vfio code with setup, exit, and finalize functions for
BAR, quirk, and VGA management. VGA is also changed to dynamic
allocation to match the other MemoryRegions.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Both platform and PCI vfio drivers create a "slow", I/O memory region
with one or more mmap memory regions overlayed when supported by the
device. Generalize this to a set of common helpers in the core that
pulls the region info from vfio, fills the region data, configures
slow mapping, and adds helpers for comleting the mmap, enable/disable,
and teardown. This can be immediately used by the PCI MSI-X code,
which needs to mmap around the MSI-X vector table.
This also changes VFIORegion.mem to be dynamically allocated because
otherwise we don't know how the caller has allocated VFIORegion and
therefore don't know whether to unreference it to destroy the
MemoryRegion or not.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In preparation for supporting capability chains on regions, wrap
ioctl(VFIO_DEVICE_GET_REGION_INFO) so we don't duplicate the code for
each caller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio-pci currently requires a host= parameter, which comes in the
form of a PCI address in [domain:]<bus:slot.function> notation. We
expect to find a matching entry in sysfs for that under
/sys/bus/pci/devices/. vfio-platform takes a similar approach, but
defines the host= parameter to be a string, which can be matched
directly under /sys/bus/platform/devices/. On the PCI side, we have
some interest in using vfio to expose vGPU devices. These are not
actual discrete PCI devices, so they don't have a compatible host PCI
bus address or a device link where QEMU wants to look for it. There's
also really no requirement that vfio can only be used to expose
physical devices, a new vfio bus and iommu driver could expose a
completely emulated device. To fit within the vfio framework, it
would need a kernel struct device and associated IOMMU group, but
those are easy constraints to manage.
To support such devices, which would include vGPUs, that honor the
VFIO PCI programming API, but are not necessarily backed by a unique
PCI address, add support for specifying any device in sysfs. The
vfio API already has support for probing the device type to ensure
compatibility with either vfio-pci or vfio-platform.
With this, a vfio-pci device could either be specified as:
-device vfio-pci,host=02:00.0
or
-device vfio-pci,sysfsdev=/sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.0
or even
-device vfio-pci,sysfsdev=/sys/bus/pci/devices/0000:02:00.0
When vGPU support comes along, this might look something more like:
-device vfio-pci,sysfsdev=/sys/devices/virtual/intel-vgpu/vgpu0@0000:00:02.0
NB - This is only a made up example path
The same change is made for vfio-platform, specifying sysfsdev has
precedence over the old host option.
Tested-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
This just catches a couple of stragglers since I posted
the last clean-includes patchset last week.
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch introduces the amd-xgbe VFIO platform device. It
allows the guest to do passthrough on a device exposing an
"amd,xgbe-seattle-v1a" compat string.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Use the macro PCI_CAP_LIST_NEXT instead of 1, so that the code would be
more self-explain.
This patch makes this change and also fixs one typo in comment.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
this function search the capability from the end, the last
size should 0x100 - pos, not 0xff - pos.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-22-git-send-email-peter.maydell@linaro.org
