Wrong type of NaN was generated for IEEE 754-2008 by MADDF.<D|S> and
MSUBF.<D|S> instructions when the arguments were (Inf, Zero, NaN) or
(Zero, Inf, NaN).
The if-else statement establishes if the system conforms to IEEE
754-1985 or IEEE 754-2008, and defines different behaviors depending
on that. In case of IEEE 754-2008, in mentioned cases of inputs,
<MADDF|MSUBF>.<D|S> returns the input value 'c' [2] (page 53) and
raises floating point exception 'Invalid Operation' [1] (pages 349,
350).
These scenarios were tested and the results in QEMU emulation match
the results obtained on the machine that has a MIPS64R6 CPU.
[1] MIPS Architecture for Programmers Volume II-a: The MIPS64
Instruction Set Reference Manual, Revision 6.06
[2] MIPS Architecture for Programmers Volume IV-j: The MIPS64
SIMD Architecture Module, Revision 1.12
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Message-Id: <1553008916-15274-2-git-send-email-mateja.marjanovic@rt-rk.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[AJB: fixed up commit message]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Isolate the target-specific choice to 3 functions instead of 6.
The code in floatx80_default_nan tried to be over-general. There are
only two targets that support this format: x86 and m68k. Thus there
is no point in inventing a mechanism for snan_bit_is_one.
Move routines that no longer have ifdefs out of softfloat-specialize.h.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reduce the number of ifdefs. Correct the result for OpenRISC
and TriCore (although TriCore fixed in target-specific code).
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Isolate the target-specific choice to 2 functions instead of 6.
The code in float16_default_nan was only correct for ARM, MIPS, and X86.
Though float16 support is rare among our targets.
The code in float128_default_nan was arguably wrong for Sparc. While
QEMU supports the Sparc 128-bit insns, no real cpu enables it.
The code in floatx80_default_nan tried to be over-general. There are
only two targets that support this format: x86 and m68k. Thus there
is no point in inventing a value for snan_bit_is_one.
Move routines that no longer have ifdefs out of softfloat-specialize.h.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For each operand, pass a single enumeration instead of a pair of booleans.
The commit also merges multiple different ifdef-selected implementations
of pickNaNMulAdd into a single function whose body is ifdef-selected.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For each operand, pass a single enumeration instead of a pair of booleans.
The commit also merges multiple different ifdef-selected implementations
of pickNaN into a single function whose body is ifdef-selected.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Only MIPS requires snan_bit_is_one to be variable. While we are
specializing softfloat behaviour, allow other targets to eliminate
this runtime check.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@mips.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These functions are now unused.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have already checked the arguments for SNaN;
we don't need to do it again.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This allows us to delete a lot of additional boilerplate
code which is no longer needed.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With a canonical representation of NaNs, we can silence an SNaN
immediately rather than delay until the final format is known.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With a canonical representation of NaNs, we can return the
default nan directly rather than delay the expansion until
the final format is known.
Note one case where we uselessly assigned to a.sign, which was
overwritten/ignored later when expanding float_class_dnan.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The new function assumes that the input is an SNaN and
does not double-check.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move the ifdef inside the relevant functions instead of
duplicating the function declarations.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Helper routines for FPU instructions and NaN definitions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
Since f3218a8 ("softfloat: add floatx80 constants")
floatx80_infinity is defined but never used.
This patch updates floatx80 functions to use
this definition.
This allows to define a different default Infinity
value on m68k: the m68k FPU defines infinity with
all bits set to zero in the mantissa.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180224201802.911-4-laurent@vivier.eu>
Move fpu/softfloat-macros.h to include/fpu/
Export floatx80 functions to be used by target floatx80
specific implementations.
Exports:
propagateFloatx80NaN(), extractFloatx80Frac(),
extractFloatx80Exp(), extractFloatx80Sign(),
normalizeFloatx80Subnormal(), packFloatx80(),
roundAndPackFloatx80(), normalizeRoundAndPackFloatx80()
Also exports packFloat32() that will be used to implement
m68k fsinh, fcos, fsin, ftan operations.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180224201802.911-2-laurent@vivier.eu>
We can now add float16_muladd and use the common decompose and
canonicalize functions to have a single implementation for
float16/32/64 muladd functions.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Mention the pseudo-code fragment from which this is based.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently float128_default_nan() returns 0xFFFF800000000000 in the
higher double word, but it should return 0x7FFF800000000000 which
is the correct higher double word for default qNAN on PowerPC.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Like the original MIPS, HPPA has the MSB of an SNaN set.
However, it has different rules for silencing an SNaN:
(1) msb is cleared and (2) msb-1 must be set if the fraction
is now zero, and (implementation defined) may be set always.
I haven't checked real hardware but chose the set always
alternative because it's easy and within spec.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Change the flag type to 'uint8_t' to fix the implicit conversion error.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 20160810185502.32015-1-bobby.prani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct the order of argument comparisons in pickNaNMulAdd().
For more info, see [1], page 53, section "3.5.3 NaN Propagation".
[1] "MIPS Architecture for Programmers Volume IV-j:
The MIPS32 SIMD Architecture Module",
Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
* reworded the subject of the patch
* swapped if/else code blocks to match the commit description]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct default NaN values (in their 16-, 32-, and 64-bit flavors).
For more info, see [1], page 84, Table 6.3 "Value Supplied When a New
Quiet NaN Is Created", and [2], page 52, Table 3.7 "Default NaN
Encodings".
[1] "MIPS Architecture For Programmers Volume II-A:
The MIPS64 Instruction Set Reference Manual",
Imagination Technologies LTD, Revision 6.04, November 13, 2015
[2] "MIPS Architecture for Programmers Volume IV-j:
The MIPS32 SIMD Architecture Module",
Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
fpu/softfloat-specialize.h is the most critical file in SoftFloat
library, since it handles numerous differences between platforms in
relation to floating point arithmetics. This patch makes the code
in this file more consistent format-wise, and hopefully easier to
debug and maintain.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch modifies SoftFloat library so that it can be configured in
run-time in relation to the meaning of signaling NaN bit, while, at the
same time, strictly preserving its behavior on all existing platforms.
Background:
In floating-point calculations, there is a need for denoting undefined or
unrepresentable values. This is achieved by defining certain floating-point
numerical values to be NaNs (which stands for "not a number"). For additional
reasons, virtually all modern floating-point unit implementations use two
kinds of NaNs: quiet and signaling. The binary representations of these two
kinds of NaNs, as a rule, differ only in one bit (that bit is, traditionally,
the first bit of mantissa).
Up to 2008, standards for floating-point did not specify all details about
binary representation of NaNs. More specifically, the meaning of the bit
that is used for distinguishing between signaling and quiet NaNs was not
strictly prescribed. (IEEE 754-2008 was the first floating-point standard
that defined that meaning clearly, see [1], p. 35) As a result, different
platforms took different approaches, and that presented considerable
challenge for multi-platform emulators like QEMU.
Mips platform represents the most complex case among QEMU-supported
platforms regarding signaling NaN bit. Up to the Release 6 of Mips
architecture, "1" in signaling NaN bit denoted signaling NaN, which is
opposite to IEEE 754-2008 standard. From Release 6 on, Mips architecture
adopted IEEE standard prescription, and "0" denotes signaling NaN. On top of
that, Mips architecture for SIMD (also known as MSA, or vector instructions)
also specifies signaling bit in accordance to IEEE standard. MSA unit can be
implemented with both pre-Release 6 and Release 6 main processor units.
QEMU uses SoftFloat library to implement various floating-point-related
instructions on all platforms. The current QEMU implementation allows for
defining meaning of signaling NaN bit during build time, and is implemented
via preprocessor macro called SNAN_BIT_IS_ONE.
On the other hand, the change in this patch enables SoftFloat library to be
configured in run-time. This configuration is meant to occur during CPU
initialization, at the moment when it is definitely known what desired
behavior for particular CPU (or any additional FPUs) is.
The change is implemented so that it is consistent with existing
implementation of similar cases. This means that structure float_status is
used for passing the information about desired signaling NaN bit on each
invocation of SoftFloat functions. The additional field in float_status is
called snan_bit_is_one, which supersedes macro SNAN_BIT_IS_ONE.
IMPORTANT:
This change is not meant to create any change in emulator behavior or
functionality on any platform. It just provides the means for SoftFloat
library to be used in a more flexible way - in other words, it will just
prepare SoftFloat library for usage related to Mips platform and its
specifics regarding signaling bit meaning, which is done in some of
subsequent patches from this series.
Further break down of changes:
1) Added field snan_bit_is_one to the structure float_status, and
correspondent setter function set_snan_bit_is_one().
2) Constants <float16|float32|float64|floatx80|float128>_default_nan
(used both internally and externally) converted to functions
<float16|float32|float64|floatx80|float128>_default_nan(float_status*).
This is necessary since they are dependent on signaling bit meaning.
At the same time, for the sake of code cleanup and simplicity, constants
<floatx80|float128>_default_nan_<low|high> (used only internally within
SoftFloat library) are removed, as not needed.
3) Added a float_status* argument to SoftFloat library functions
XXX_is_quiet_nan(XXX a_), XXX_is_signaling_nan(XXX a_),
XXX_maybe_silence_nan(XXX a_). This argument must be present in
order to enable correct invocation of new version of functions
XXX_default_nan(). (XXX is <float16|float32|float64|floatx80|float128>
here)
4) Updated code for all platforms to reflect changes in SoftFloat library.
This change is twofolds: it includes modifications of SoftFloat library
functions invocations, and an addition of invocation of function
set_snan_bit_is_one() during CPU initialization, with arguments that
are appropriate for each particular platform. It was established that
all platforms zero their main CPU data structures, so snan_bit_is_one(0)
in appropriate places is not added, as it is not needed.
[1] "IEEE Standard for Floating-Point Arithmetic",
IEEE Computer Society, August 29, 2008.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Tested-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Tested-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
* cherry-picked 2 chunks from patch #2 to fix compilation warnings]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch adds a file for all the FPU related helpers with all the includes,
useful defines, and a function to update the status bits. Additionally it adds
a mask for the rounding mode bits of PSW as well as all the opcodes for the
FPU instructions.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <1457708597-3025-2-git-send-email-kbastian@mail.uni-paderborn.de>
Replace the int8 softfloat-specific typedef with int8_t.
This change was made with
find include hw fpu target-* -name '*.[ch]' | xargs sed -i -e 's/\bint8\b/int8_t/g'
together with manual removal of the typedef definition, and
manual undoing of various mis-hits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Leon Alrae <leon.alrae@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Message-id: 1452603315-27030-6-git-send-email-peter.maydell@linaro.org
Expand out STATUS_PARAM wherever it is used and delete the definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The code in the softfloat source files is under a mixture of
licenses: the original code and many changes from QEMU contributors
are under the base SoftFloat-2a license; changes from Stefan Weil
and RedHat employees are GPLv2-or-later; changes from Fabrice Bellard
are under the BSD license. Clarify this in the comments at the
top of each affected source file, including a statement about
the assumed licensing for future contributions, so we don't need
to remember to ask patch submitters explicitly to pick a license.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Andreas Färber <afaerber@suse.de>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Avi Kivity <avi.kivity@gmail.com>
Acked-by: Ben Taylor <bentaylor.solx86@gmail.com>
Acked-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Christophe Lyon <christophe.lyon@st.com>
Acked-by: Fabrice Bellard <fabrice@bellard.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Paul Brook <paul@codesourcery.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Richard Sandiford <rdsandiford@googlemail.com>
Acked-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1421073508-23909-5-git-send-email-peter.maydell@linaro.org
Revert the parts of commits b645bb4885 and 5a6932d51d which are still
in the codebase and under a SoftFloat-2b license.
Reimplement support for architectures where the most significant bit
in the mantissa is 1 for a signaling NaN rather than a quiet NaN,
by adding handling for SNAN_BIT_IS_ONE being set to the functions
which test values for NaN-ness.
This includes restoring the bugfixes lost in the reversion where
some of the float*_is_quiet_nan() functions were returning true
for both signaling and quiet NaNs.
[This is a mechanical squashing together of two separate "revert"
and "reimplement" patches.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1421073508-23909-4-git-send-email-peter.maydell@linaro.org
This commit applies the changes to master which correspond to
replacing commit 158142c2c2 with a set of changes made by:
* taking the SoftFloat-2a release
* mechanically transforming the block comment style
* reapplying Fabrice's original changes from 158142c2c2
This commit was created by:
diff -u 158142c2c2 import-sf-2a
patch -p1 --fuzz 10 <../relicense-patch.txt
(where import-sf-2a is the branch resulting from the changes above).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1421073508-23909-2-git-send-email-peter.maydell@linaro.org
Add a pickNaNMulAdd function for MIPS, implementing NaN propagation
rules for MIPS fused multiply-add instructions.
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
NaN propagation rule: leftmost NaN in the expression gets propagated to
the result.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Architectures that don't have signaling NaNs can define
NO_SIGNALING_NANS, it will make float*_is_quiet_nan return 1 for any NaN
and float*_is_signaling_nan always return 0.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
C99 appears to consider compound literals as non-constants, and complains
when they are used in static initializers. Switch to ordinary initializer
syntax.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Andreas Färber <afaerber@suse.de>
Reported-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Implement fused multiply-add as a softfloat primitive. This implements
"a+b*c" as a single step without any intermediate rounding; it is
specified in IEEE 754-2008 and implemented in a number of CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most definitions in softfloat.h are really target-independent, but the
file is not because it includes definitions of the default NaN values.
Change those to variables to allow including softfloat.h from files that
are not compiled per-target. By making them const, the compiler is
allowed to optimize them into softfloat functions that use them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Now that softfloat-native is gone, there is no real point on not always
enabling floatx80 and float128 support.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The floatx80 format uses an explicit bit that should be taken into account
when converting to and from commonNaN format.
When converting to commonNaN, the explicit bit should be removed if it is
a 1, and a default NaN should be used if it is 0.
When converting from commonNan, the explicit bit should be added.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
They are defined with the same semantics as the POSIX types,
so prefer those for consistency. Suggested by Peter Maydell.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SoftFloat license requires "prominent notice that the work
is derivative". Having added features like improved 16-bit support
for arm already, add such a notice to the sources.
softfloat-native.[ch] are not under the SoftFloat license
and thus are not changed.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
These special values are needed to implement some helper functions,
which return/use these values in some cases.
Signed-off-by: Christophe Lyon <christophe.lyon@st.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Correctly handle NaNs in float16_to_float32(), by defining and
using a float16ToCommonNaN() function, as we do with the other formats.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
