Per the Physical Layer Simplified Spec. "5.3 CSD Register":
"The maximum block length might therefore be in the range 512...2048 bytes"
Therefore 3 hexdigits are enough to report the block length.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add an optional paramter num_queues for device, and set it
to 64 by default.
Signed-off-by: Weiping Zhang <zhangweiping@didichuxing.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Comparisons of mode_t with -1 require an explicit cast, since mode_t
is unsigned on Darwin.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
strchrnul is a GNU extension and thus unavailable on a number of targets.
In the review for a commit removing strchrnul from 9p, I was asked to
create a qemu_strchrnul helper to factor out this functionality.
Do so, and use it in a number of other places in the code base that inlined
the replacement pattern in a place where strchrnul could be used.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This include both userspace and in-kernel ioapic. Note that the numbers
can be inaccurate for kvm-ioapic. One reason is the same with
kvm-i8259, that when irqfd is used, irqs can be delivered all inside
kernel without our notice. Meanwhile, kvm-ioapic is specially treated
when irq numbers <ISA_NUM_IRQS, those irqs will be delivered in kernel
too via kvm-i8259 (please refer to kvm_pc_gsi_handler).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So that now it looks better when with other irqchips.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
People start to use "info pic" for all kinds of irqchip dumps. Let x86
ioapic join the family. It dumps the same thing as "info ioapic".
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-3-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
MIPS jazz is the last user of the legacy esp_init() function so move creation
of the ESP device over to use qdev.
Note that the esp_reset and dma_enable qemu_irqs are currently unused and so
we do not wire these up and instead remove the variables to prevent the
compiler emitting unused variable warnings.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Let's try to reduce error handling a bit. In the plug/unplug case, the
device was realized and therefore we can assume that getting access to
the memory region will not fail.
For get_vmstate_memory_region() this is already handled that way.
Document both cases.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-13-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We might get a call to get_memory_region() before the device has been
realized. We should return a consistent value, as the return value
will e.g. later on be used in the pre_plug handler.
To avoid duplicating too much code, factor the initialization and checks
out into a helper function.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-12-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way we can easily check if the region has already been inititalized
without having to rely on the size of an uninitialized region being 0.
Free the region in nvdimm_finalize() and not in unrealize() as we will
allow to create the region before realization in following patches.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-11-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't allow to modify it after realization. So we can simply turn
it into a static property.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-10-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Importantly, get_vmstate_memory_region() should also fail with a proper
error if called before the device is realized. For a PCDIMM, both functions
are to return the same thing, so share the implementation.
All current users are called after the device has been realized, so we
can expect the calls to succeed.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-9-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unused, so let's remove it.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-8-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Our parent class (PC_DIMM) provides exactly the same function.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-7-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can perform these checks before the device is actually realized.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-6-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not used outside of pc-dimm.c and there shouldn't be other users. If
other devices (e.g. memory devices) ever have to also use slots, then we
will have to factor this out.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's rename it to make it look more consistent.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a similar naming scheme as spapr. This way, we can go ahead and
rename e.g. pc_dimm_memory_plug to pc_dimm_plug, which avoids
confusion.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-3-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not needed anymore, let's drop it.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preferred way to select the KVM accelerator is to use "-accel kvm"
these days, so let's be consistent in our documentation and help texts.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1528866321-23886-3-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The start of the address space indicates which maximum alignment is
supported by our machine (e.g. ppc, x86 1GB). This is helpful to
catch fragmenting guest physical memory in strange fashions.
Right now we can crash QEMU by e.g. (there might be easier examples)
qemu-system-x86_64 -m 256M,maxmem=20G,slots=2 \
-object memory-backend-file,id=mem0,size=8192M,mem-path=/dev/zero,align=8192M \
-device pc-dimm,id=dimm1,memdev=mem0
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180607154705.6316-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only retry on serial_xmit if qemu_chr_fe_write returns 0, as this is the
only recoverable error.
Retrying with any other scenario, in addition to being a waste of CPU
cycles, can compromise the Guest stability if by the vCPU issuing the
write and the main loop thread are, by chance or explicit pinning,
running on the same pCPU.
Previous discussion:
https://lists.nongnu.org/archive/html/qemu-devel/2018-05/msg06998.html
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <1528185295-14199-1-git-send-email-slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
virtio-rng device causes old guest kernels(2.6.32) to hang on latest qemu.
The driver attempts to read from the virtio-rng device too early in it's
initialization. Qemu detects guest is not ready and returns, resulting in
hang.
To fix handle pending requests when guest is running and driver status is
set to 'VIRTIO_CONFIG_S_DRIVER_OK'.
CC: qemu-stable@nongnu.org
Reported-by: Sergio lopez <slopezpa@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently we use memory_region_init_rom_nomigrate() to create
the "io" memory region to pass to pci_register_root_bus().
This is a dummy region, because this PCI controller doesn't
support accesses to PCI IO space.
There is no reason for the dummy region to be a RAM region;
it is only used as a place where PCI BARs can be mapped,
and if you could get a PCI card to do a bus master access
to the IO space it should not get acts-like-RAM behaviour.
Use a simple container memory region instead. (We do have
one PCI card model which can do bus master accesses to IO
space -- the LSI53C895A SCSI adaptor.)
This avoids the oddity of having a memory region which is
RAM but where the RAM is not migrated.
Note that the size of the region we use here has no
effect on behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Currently we use memory_region_init_rom_nomigrate() to create
the "bios.1fc" memory region, and we don't manually register
it with vmstate_register_ram(). This currently means that its
contents are migrated but as a ram block whose name is the empty
string; in future it may mean they are not migrated at all. Use
memory_region_init_ram() instead.
Note that this is a a cross-version migration compatibility break
for the "malta" machine.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Currently we use memory_region_init_rom_nomigrate() to create
the "boston.flash" memory region, and we don't manually register
it with vmstate_register_ram(). This currently means that its
contents are migrated but as a ram block whose name is the empty
string; in future it may mean they are not migrated at all. Use
memory_region_init_ram() instead.
Note that this is a a cross-version migration compatibility break
for the "boston" machine.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Determining the size of a field is useful when you don't have a struct
variable handy. Open-coding this is ugly.
This patch adds the sizeof_field() macro, which is similar to
typeof_field(). Existing instances are updated to use the macro.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180614164431.29305-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We support up to 6 levels, but those are encoded as 10b according to the
AMD IOMMU spec (chapter 3.3.1, Extended Feature Register).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Counting from the IVHD ID field to the all-devices entry, we have 28
bytes, not 36.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* aspeed: set APB clocks correctly (fixes slowdown on palmetto)
* smmuv3: cache config data and TLB entries
* v7m/v8m: support read/write from MPU regions smaller than 1K
* various: clean up logging/debug messages
* xilinx_spips: Make dma transactions as per dma_burst_size
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZiOR
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180626' into staging
target-arm queue:
* aspeed: set APB clocks correctly (fixes slowdown on palmetto)
* smmuv3: cache config data and TLB entries
* v7m/v8m: support read/write from MPU regions smaller than 1K
* various: clean up logging/debug messages
* xilinx_spips: Make dma transactions as per dma_burst_size
# gpg: Signature made Tue 26 Jun 2018 17:55:46 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180626: (32 commits)
aspeed/timer: use the APB frequency from the SCU
aspeed: initialize the SCU controller first
aspeed/scu: introduce clock frequencies
hw/arm/smmuv3: Add notifications on invalidation
hw/arm/smmuv3: IOTLB emulation
hw/arm/smmuv3: Cache/invalidate config data
hw/arm/smmuv3: Fix translate error handling
target/arm: Handle small regions in get_phys_addr_pmsav8()
target/arm: Set page (region) size in get_phys_addr_pmsav7()
tcg: Support MMU protection regions smaller than TARGET_PAGE_SIZE
hw/arm/stellaris: Use HWADDR_PRIx to display register address
hw/arm/stellaris: Fix gptm_write() error message
hw/net/smc91c111: Use qemu_log_mask(UNIMP) instead of fprintf
hw/net/smc91c111: Use qemu_log_mask(GUEST_ERROR) instead of hw_error
hw/net/stellaris_enet: Use qemu_log_mask(GUEST_ERROR) instead of hw_error
hw/net/stellaris_enet: Fix a typo
hw/arm/stellaris: Use qemu_log_mask(UNIMP) instead of fprintf
hw/arm/omap: Use qemu_log_mask(GUEST_ERROR) instead of fprintf
hw/arm/omap1: Use qemu_log_mask(GUEST_ERROR) instead of fprintf
hw/i2c/omap_i2c: Use qemu_log_mask(UNIMP) instead of fprintf
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The System Control Unit should be initialized first as it drives all
the configuration of the SoC and other device models.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All Aspeed SoC clocks are driven by an input source clock which can
have different frequencies : 24MHz or 25MHz, and also, on the Aspeed
AST2400 SoC, 48MHz. The H-PLL (CPU) clock is defined from a
calculation using parameters in the H-PLL Parameter register or from a
predefined set of frequencies if the setting is strapped by hardware
(Aspeed AST2400 SoC). The other clocks of the SoC are then defined
from the H-PLL using dividers.
We introduce first the APB clock because it should be used to drive
the Aspeed timer model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On TLB invalidation commands, let's call registered
IOMMU notifiers. Those can only be UNMAP notifiers.
SMMUv3 does not support notification on MAP (VFIO).
This patch allows vhost use case where IOTLB API is notified
on each guest IOTLB invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We emulate a TLB cache of size SMMU_IOTLB_MAX_SIZE=256.
It is implemented as a hash table whose key is a combination
of the 16b asid and 48b IOVA (Jenkins hash).
Entries are invalidated on TLB invalidation commands, either
globally, or per asid, or per asid/iova.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1529653501-15358-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's cache config data to avoid fetching and parsing STE/CD
structures on each translation. We invalidate them on data structure
invalidation commands.
We put in place a per-smmu mutex to protect the config cache. This
will be useful too to protect the IOTLB cache. The caches can be
accessed without BQL, ie. in IO dataplane. The same kind of mutex was
put in place in the intel viommu.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In case the STE's config is "Bypass" we currently don't set the
IOMMUTLBEntry perm flags and the access does not succeed. Also
if the config is 0b0xx (Aborted/Reserved), decode_ste and
smmuv3_decode_config currently returns -EINVAL and we don't enter
the expected code path: we record an event whereas we should not.
This patch fixes those bugs and simplifies the error handling.
decode_ste and smmuv3_decode_config now return 0 if aborted or
bypassed config was found. Only bad config info produces negative
error values. In smmuv3_translate we more clearly differentiate
errors, bypass/smmu disabled, aborted and success cases. Also
trace points are differentiated.
Fixes: 9bde7f0674 ("hw/arm/smmuv3: Implement translate callback")
Reported-by: jia.he@hxt-semitech.com
Signed-off-by: jia.he@hxt-semitech.com
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-17-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Missed in df3692e04b.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-16-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() finally calls abort(), but there is no need to abort here.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() finally calls abort(), but there is no need to abort here.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-13-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TCMI_VERBOSE is no more used, drop the OMAP_8/16/32B_REG macros.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180624040609.17572-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Qspi dma has a burst length of 64 bytes, So limit the transactions w.r.t
dma-burst-size property.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1529660880-30376-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also handle the fake transfers for dummy bytes in this setup
routine. It will be useful when we activate MMIO execution.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only the flash type is strapped by HW. The 4BYTE mode is set by
firmware when the flash device is detected.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When configured in dual I/O mode, address and data are sent in dual
mode, including the dummy byte cycles in between. Adapt the count to
the IO setting.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
> CID 1393621: (OVERFLOW_BEFORE_WIDEN)
> Potentially overflowing expression "stride * s->height" with type "unsigned
> int" (32 bits, unsigned) is evaluated using +32-bit arithmetic, and then used
> in a context that expects an expression of type "hwaddr" (64 bits, unsigned).
Fix by changing stride from uint32_t to hwaddr.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180626083120.19515-1-kraxel@redhat.com
This makes sure the regions are properly cleaned when unplugging -device
seconday-vga.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180626060941.8326-1-kraxel@redhat.com
The "I" bit in PIO Setup and D2H FISes is exclusively a device concept
and the irqstatus register in the controller does not matter. The SATA
spec says when it should be one; for D2H FISes in practice it is always
set, while the PIO Setup FIS has several subcases that are documented in
the patch.
Also, the PIO Setup FIS interrupt is actually generated _after_ data
has been received.
Someone should probably spend some time reading the SATA specification and
figuring out the more obscure fields in the PIO Setup FIS, but this is enough
to fix SeaBIOS booting from ATAPI CD-ROMs over an AHCI controller.
Fixes: 956556e131
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180622165159.19863-1-pbonzini@redhat.com
[Minor edit to avoid ATAPI comment ambiguity. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
The oldest machine type which is still used in a still maintained distro
is a pc-0.12 based machine type in RHEL6, so everything that is older
than pc-0.12 should not be used anymore. Thus let's deprecate pc-0.10
and pc-0.11 so that we can finally remove them in a future release.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1529917512-10528-1-git-send-email-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Also add a compat property to disable it for old machine types,
needed for live migration compatibility.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-6-kraxel@redhat.com
If some event caused some larger playback hickup the fine-grained timer
adjust isn't able to recover. Use a buffer overruns as indicator for
that. Reset timer adjust logic in case we detected one.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-5-kraxel@redhat.com
We have some jitter in the audio timer call frequency and buffer sizes.
So it is rather pointless trying to be very exact, effect is a constant
up+down adjustment. So adjust only in case we are off too much.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-4-kraxel@redhat.com
Currently, the HDA device tries to sync itself with the QEMU audio
backend by waiting for the guest driver to handle buffer completion
interrupts. This causes the backend to often read too much data from the
device, as well as running out of data whenever the guest takes too long
to handle the interrupt.
According to the HDA specification, the guest is also not required to
use interrupts, but can also sync itself by polling the LPIB registers.
This patch will introduce high frequency (1000Hz) timers that interface
with the device and allow for much smoother emulation of the LPIB
registers. Since the timing is now provided by these timers, the need
to wait for buffer completion interrupts also ceases.
Signed-off-by: Martin Schrodt <martin@schrodt.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-2-kraxel@redhat.com
Message-id: 20171015184033.2951-3-martin@schrodt.org
[ kraxel: keep old code for compatibility with older qemu versions,
add property to switch code paths at runtime ]
[ kraxel: new code is disabled by default, use-timer=on enables it ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1T5q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180622' into staging
target-arm queue:
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
# gpg: Signature made Fri 22 Jun 2018 13:56:00 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180622: (28 commits)
xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
vl.c: Don't zero-initialize statics for serial_hds
target/arm: Strict alignment for ARMv6-M and ARMv8-M Baseline
target/arm: Introduce ARM_FEATURE_M_MAIN
hw/arm/mps2-tz.c: Instantiate MPCs
hw/arm/iotkit: Wire up MPC interrupt lines
hw/arm/iotkit: Instantiate MPC
hw/misc/iotkit-secctl.c: Implement SECMPCINTSTATUS
hw/misc/tz_mpc.c: Honour the BLK_LUT settings in translate
hw/misc/tz-mpc.c: Implement correct blocked-access behaviour
hw/misc/tz-mpc.c: Implement registers
hw/misc/tz-mpc.c: Implement the Arm TrustZone Memory Protection Controller
xlnx-zynqmp: Swap Cortex-R5 for Cortex-R5F
target-arm: Add the Cortex-R5F
hw/arm/virt: Increase max_cpus to 512
hw/arm/virt: Use 256MB ECAM region by default
hw/arm/virt: Add virt-3.0 machine type
hw/arm/virt: Add a new 256MB ECAM region
hw/arm/virt: Register two redistributor regions when necessary
hw/arm/virt-acpi-build: Advertise one or two GICR structures
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The xen pci_assign_dev_load_option_rom() currently creates a RAM
memory region with memory_region_init_ram_nomigrate(), and then
manually registers it with vmstate_register_ram(). In fact for
its only callsite, the 'owner' pointer we use for the init call
and the '&dev->qdev' pointer we use for the vmstate_register_ram()
call refer to the same object. Simplify the function to only
take a pointer to the device once instead of twice, and use
memory_region_init_ram() which automatically does the vmstate
register for us.
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate and wire up the Memory Protection Controllers
in the MPS2 board itself.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-9-peter.maydell@linaro.org
The interrupt outputs from the MPC in the IoTKit and the expansion
MPCs in the board must be wired up to the security controller, and
also all ORed together to produce a single line to the NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-8-peter.maydell@linaro.org
Wire up the one MPC that is part of the IoTKit itself. For the
moment we don't wire up its interrupt line.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-7-peter.maydell@linaro.org
Implement the SECMPCINTSTATUS register. This is the only register
in the security controller that deals with Memory Protection
Controllers, and it simply provides a read-only view of the
interrupt lines from the various MPCs in the system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180620132032.28865-6-peter.maydell@linaro.org
The final part of the Memory Protection Controller we need to
implement is actually using the BLK_LUT data programmed by the
guest to determine whether to block the transaction or not.
Since this means we now change transaction mappings when
the guest writes to BLK_LUT, we must also call the IOMMU
notifiers at that point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-5-peter.maydell@linaro.org
The MPC is guest-configurable for whether blocked accesses:
* should be RAZ/WI or cause a bus error
* should generate an interrupt or not
Implement this behaviour in the blocked-access handlers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-4-peter.maydell@linaro.org
Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
The ZynqMP has Cortex-R5Fs with the optional FPU enabled.
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180529124707.3025-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virt 3.0 now allows up to 512 vcpus whereas for earlier machine
types, max_cpus was set to 255 and any attempt to start the
machine with vcpus > 255 was rejected at a very early stage,
in vl.c/main level.
512 is the max supported by KVM. Anyway the actual vcpu count
that can be achieved depends on other parameters such as the
acceleration mode, the vgic version, the host kernel version.
Those are discovered later on.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-12-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With a VGICv3 KVM device, if the number of vcpus exceeds the
capacity of the legacy redistributor region (123 redistributors),
we now attempt to register a second redistributor region. Up to
512 redistributors can fit in this latter on top of the 123 allowed
by the legacy redistributor region.
Registering this second redistributor region is possible if the
host kernel supports the following VGICv3 KVM device group/attribute:
KVM_DEV_ARM_VGIC_GRP_ADDR/KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION.
In case the host kernel does not support the registration of several
redistributor regions and the requested number of vcpus exceeds the
capacity of the legacy redistributor region, the GICv3 device
initialization fails with a proper error message and qemu exits.
At the moment the max number of vcpus still is capped by the
virt machine class max_cpus.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-8-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Depending on the number of smp_cpus we now register one or two
GICR structures.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-7-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's check if KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION is supported.
If not, we check the number of redist region is equal to 1 and use the
legacy KVM_VGIC_V3_ADDR_TYPE_REDIST attribute. Otherwise we use
the new attribute and allow to register multiple regions to the
KVM device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
for KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION attribute, the attribute
data pointed to by kvm_device_attr.addr is a OR of the
redistributor region address and other fields such as the index
of the redistributor region and the number of redistributors the
region can contain.
The existing machine init done notifier framework sets the address
field to the actual address of the device and does not allow to OR
this value with other fields.
This patch extends the KVMDevice struct with a new kda_addr_ormask
member. Its value is passed at registration time and OR'ed with the
resolved address on kvm_arm_set_device_addr().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529072910-16156-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When either GICD_IPRIORITYR or GICR_IPRIORITYR is read as a 32-bit
register, the post left-shift operator in the for loop causes an
extra shift after the least significant byte has been placed.
The 32-bit value actually returned is therefore the expected value
shifted left by 8 bits.
Signed-off-by: Amol Surati <suratiamol@gmail.com>
Message-id: 20180614054857.26248-1-suratiamol@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently during KVM initialization on POWER, kvm_fixup_page_sizes()
rewrites a bunch of information in the cpu state to reflect the
capabilities of the host MMU and KVM. This overwrites the information
that's already there reflecting how the TCG implementation of the MMU will
operate.
This means that we can get guest-visibly different behaviour between KVM
and TCG (and between different KVM implementations). That's bad. It also
prevents migration between KVM and TCG.
The pseries machine type now has filtering of the pagesizes it allows the
guest to use which means it can present a consistent model of the MMU
across all accelerators.
So, we can now replace kvm_fixup_page_sizes() with kvm_check_mmu() which
merely verifies that the expected cpu model can be faithfully handled by
KVM, rather than updating the cpu model to match KVM.
We call kvm_check_mmu() from the spapr cpu reset code. This is a hack:
conceptually it makes more sense where fixup_page_sizes() was - in the KVM
cpu init path. However, doing that would require moving the platform's
pagesize filtering much earlier, which would require a lot of work making
further adjustments. There wouldn't be a lot of concrete point to doing
that, since the only KVM implementation which has the awkward MMU
restrictions is KVM HV, which can only work with an spapr guest anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
KVM HV has some limitations (deriving from the hardware) that mean not all
host-cpu supported pagesizes may be usable in the guest. At present this
means that KVM guests and TCG guests may see different available page sizes
even if they notionally have the same vcpu model. This is confusing and
also prevents migration between TCG and KVM.
This patch makes the environment consistent by always allowing the same set
of pagesizes. Since we can't remove the KVM limitations, we do this by
always applying the same limitations it has, even to TCG guests.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the sm501 specs the hardware cursor colors are to be given in
the rgb565 format, but the code currently interprets them as bgr565.
Therefore, the colors of the hardware cursors are wrong in the QEMU
display, e.g., the standard mouse pointer of AmigaOS appears blue instead
of red. This change fixes this issue by replacing the existing naive
bgr565 => rgb888 conversion with a standard rgb565 => rgb888 one that also
scales the color component values properly.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
ppc_check_compat() is used in a number of places to check if a cpu object
supports a certain compatiblity mode, subject to various constraints.
It takes a PowerPCCPU *, however it really only depends on the cpu's class.
We have upcoming cases where it would be useful to make compatibility
checks before we fully instantiate the cpu objects.
ppc_type_check_compat() will now make an equivalent check, but based on a
CPU's QOM typename instead of an instantiated CPU object.
We make use of the new interface in several places in spapr, where we're
essentially making a global check, rather than one specific to a particular
cpu. This avoids some ugly uses of first_cpu to grab a "representative"
instance.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The device tree node of the ISA bus was being partially done in
different places. Move all the nodes creation under the same routine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU implements the "Shared Processor LPAR" (SPLPAR) option, which allows
the hypervisor to time-slice a physical processor into multiple virtual
processor. The intent is to allow more guests to run, and to optimize
processor utilization.
The guest OS can cede idle VCPUs, so that their processing capacity may
be used by other VCPUs, with the H_CEDE hcall. The guest OS can also
optimize spinlocks, by confering the time-slice of a spinning VCPU to the
spinlock holder if it's currently notrunning, with the H_CONFER hcall.
Both hcalls depend on a "Virtual Processor Area" (VPA) to be registered
by the guest OS, generally during early boot. Other per-VCPU areas can
be registered: the "SLB Shadow Buffer" which allows a more efficient
dispatching of VCPUs, and the "Dispatch Trace Log Buffer" (DTL) which
is used to compute time stolen by the hypervisor. Both DTL and SLB Shadow
areas depend on the VPA to be registered.
The VPA/SLB Shadow/DTL are state that QEMU should migrate, but this doesn't
happen, for no apparent reason other than it was just never coded. This
causes the features listed above to stop working after migration, and it
breaks the logic of the H_REGISTER_VPA hcall in the destination.
The VPA is set at the guest request, ie, we don't have to migrate
it before the guest has actually set it. This patch hence adds an
"spapr_cpu/vpa" subsection to the recently introduced per-CPU machine
data migration stream.
Since DTL and SLB Shadow are optional and both depend on VPA, they get
their own subsections "spapr_cpu/vpa/slb_shadow" and "spapr_cpu/vpa/dtl"
hanging from the "spapr_cpu/vpa" subsection.
Note that this won't break migration to older QEMUs. Is is already handled
by only registering the vmstate handler for per-CPU data with newer machine
types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- accommodate guests using vfio-ccw without specifying unlimited
prefetch, but actually working fine
- add cpu model for the z14 Model ZR1
- add support for pxelinux.cfg-style network booting to the s390x
firmware
-----BEGIN PGP SIGNATURE-----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=hMax
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180619' into staging
- cleanup in virtio-ccw
- accommodate guests using vfio-ccw without specifying unlimited
prefetch, but actually working fine
- add cpu model for the z14 Model ZR1
- add support for pxelinux.cfg-style network booting to the s390x
firmware
# gpg: Signature made Tue 19 Jun 2018 10:33:06 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180619:
pc-bios/s390-ccw: Update the s390-netboot.img binary
pc-bios/s390-ccw: Optimize the s390-netboot.img for size
pc-bios/s390-ccw/net: Try to load pxelinux.cfg file accoring to the UUID
pc-bios/s390-ccw/net: Add support for pxelinux-style config files
pc-bios/s390-ccw/net: Update code for the latest changes in SLOF
roms: Update SLOF submodule to current status
pc-bios/s390-ccw: define loadparm length
s390x/cpumodels: add z14 Model ZR1
s390x/ipl: Try to detect Linux vs non Linux for initial IPL PSW
vfio-ccw: remove orb.c64 (64 bit data addresses) check
vfio-ccw: add force unlimited prefetch property
virtio-ccw: clean up notify
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 802cbcb730, most issues have been fixed when qemu guest
migration. But the queue size still need to check whether is equal to
PS2_QUEUE_SIZE. If yes, the wptr should set as 0. Or, wptr would larger
than PS2_QUEUE_SIZE and never come back when ps2_queue_noirq is called.
This could lead to OOB access, add check to avoid it.
Signed-off-by: liujunjie <liujunjie23@huawei.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 20180607080237.12360-1-liujunjie23@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Right now the IPL device always starts from address 0x10000 (the usual
Linux entry point). To run other guests (e.g. test programs) it is
useful to use the IPL PSW from address 0. We can use the Linux magic
at 0x10008 to decide.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20180612125933.262679-1-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The vfio-ccw module does the check too, and there is actually no
technical obstacle for supporting fmt 1 idaws. Let us be ready for the
beautiful day when fmt 1 idaws become supported by the vfio-ccw kernel
module. QEMU does not have to do a thing for that, except not insisting
on this check.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Jason J. Herne <jjherne@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180524175828.3143-3-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There is at least one guest (OS) such that although it does not rely on
the guarantees provided by ORB 1 word 9 bit (aka unlimited prefetch, aka
P bit) not being set, it fails to tell this to the machine.
Usually this ain't a big deal, as the original purpose of the P bit is to
allow for performance optimizations. vfio-ccw however can not provide the
guarantees required if the bit is not set.
It is not possible to implement support for the P bit not set without
transitioning to lower level protocols for vfio-ccw. So let's give the
user the opportunity to force setting the P bit, if the user knows this
is safe. For self modifying channel programs forcing the P bit is not
safe. If the P bit is forced for a self modifying channel program things
are expected to break in strange ways.
Let's also avoid warning multiple about P bit not set in the ORB in case
P bit is not told to be forced, and designate the affected vfio-ccw
device.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Acked-by: Jason J. Herne <jjherne@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180524175828.3143-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Coverity recently started complaining about virtio_ccw_notify(). Turns
out, there is a couple of things that can be cleaned up. Let's clean!
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: CID 1390619
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20180516132757.68558-1-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is wrong. object_finalize_child_property()'s unref balances the
ref in object_property_add_child(). qbus_realize's unref balances the
ref that was initially placed by object_new/object_initialize.
This reverts commit f3d58385a6.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The USB device don't hold the bus. There is no ASAN related reports
anymore.
This reverts commit cd7bc87868.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bus is not owned by the device.
This reverts commit 410a096adf.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 3d85885a1b tried to fix error handling, but it actually
went into the wrong direction by dropping the local Error *.
In the default KVM case, the rationale is to try the in-kernel XICS first,
and if not possible, to fallback to userland XICS. Passing errp everywhere
makes this fallback impossible if errp is &error_fatal (which happens to
be the case). And anyway, if the caller would pass a regular &local_err,
things would be worse: we could possibly pass an already set *errp to
error_setg() and crash, or return an error even in case of success.
So we definitely need a local Error * and only propagate it when we're
done with the fallback logic. This is what this patch does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The instance_init function of devices should always succeed to be able
to introspect the device. However, the instance_init function of the
"openprom" device can currently fail, for example like this:
$ echo "{'execute':'qmp_capabilities'}"\
"{'execute':'device-list-properties',"\
" 'arguments':{'typename':'openprom'}}" \
| sparc64-softmmu/qemu-system-sparc64 -M sun4v,accel=qtest -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 91, "minor": 11, "major": 2},
"package": "build-all"}, "capabilities": []}}
{"return": {}}
RAMBlock "sun4u.prom" already registered, abort!
Aborted (core dumped)
This should not happen. Fix this problem by moving the affected code from
instance_init into a realize function instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
On the Alpha DP264 machine, the Cirrus VGA is I/O mapped
in the 3C0H-3CFH range, thus I/O base used by the parallel
device clashes, and since a4cb773928 the VGA is not
working:
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
00000801fc000000-00000801fdffffff (prio 0, i/o): pci0-io
...
00000801fc0003b4-00000801fc0003b5 (prio 0, i/o): vga
00000801fc0003ba-00000801fc0003ba (prio 0, i/o): vga
00000801fc0003bc-00000801fc0003c3 (prio 0, i/o): parallel
^^^ ^^^^^^^^
00000801fc0003c0-00000801fc0003cf (prio 0, i/o): vga
^^^
00000801fc0003d4-00000801fc0003d5 (prio 0, i/o): vga
00000801fc0003da-00000801fc0003da (prio 0, i/o): vga
...
As there is no particular reason to use this base address
(introduced in 7bea0dd434), change to 378H which is the
default on PC machines.
Reported-by: Emilio G. Cota <cota@braap.org>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180614233935.26585-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
This extracts from the PvChip realize routine the part creating the
cores. On Power9, we will need to create the cores after the Xive
interrupt controller is created.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves some code out from spapr_cpu_core_realize() for clarity. No
functional change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_realize_vcpu() function doesn't rollback in case of error.
This isn't a problem with coldplugged CPUs because the machine won't
start and QEMU will exit. Hotplug is a different story though: the
CPU thread is started under object_property_set_bool() and it assumes
it can access the CPU object.
If icp_create() fails, we return an error without unregistering the
reset handler for this CPU, and we let the underlying QEMU thread for
this CPU alive. Since spapr_cpu_core_realize() doesn't care to unrealize
already realized CPUs either, but happily frees all of them anyway, the
CPU thread crashes instantly:
(qemu) device_add host-spapr-cpu-core,core-id=1,id=gku
GKU: failing icp_create (cpu 0x11497fd0)
^^^^^^^^^^
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffee3feaa0 (LWP 24725)]
0x00000000104c8374 in object_dynamic_cast_assert (obj=0x11497fd0,
^^^^^^^^^^^^^^
pointer to the CPU object
623 trace_object_dynamic_cast_assert(obj ? obj->class->type->name
(gdb) p obj->class->type
$1 = (Type) 0x0
(gdb) p * obj
$2 = {class = 0x10ea9c10, free = 0x11244620,
^^^^^^^^^^
should be g_free
(gdb) p g_free
$3 = {<text variable, no debug info>} 0x7ffff282bef0 <g_free>
obj is a dangling pointer to the CPU that was just destroyed in
spapr_cpu_core_realize().
This patch adds proper rollback to both spapr_realize_vcpu() and
spapr_cpu_core_realize().
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fixed a conflict due to a change in my tree]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 94ad93bd97 (QEMU 2.12) switched to instantiate CPUs separately
but it missed to adapt the error path accordingly. If something fails in
the CPU creation loop, then the CPU object that was just created is leaked.
The error paths in this function are a bit obfuscated, and adding
yet another label to free this CPU object makes it worse. We should
move the block of the loop to a separate function, with a proper
rollback path, but this is a bigger cleanup.
For now, let's just fix the bug by adding the missing calls to
object_unref(). This will allow easier backport to older QEMU
versions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently we don't have any unrealize path for pnv cpu cores. We get away
with this because we don't yet support cpu hotplug for pnv.
However, we're going to want it eventually, and in the meantime, it makes
it non-obvious why there are a bunch of allocations on the realize() path
that don't have matching frees.
So, implement the missing unrealize path.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
pnv_cpu_init() is only called from the the pnv cpu core realize path, and
really only can be called from there. So fold it into its caller, which
we also rename for brevity.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
In pnv_core_realize() we call two functions with an Error * parameter in
succession, which will go badly if they both cause errors. In fact, a
failure in either of them indicates a qemu internal error, so we can just
use &error_abort in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
