In preparation for having some more common semihosting code let's
excise the current config magic from vl.c into its own file. We shall
later add more conditionals to the build configurations so we can
avoid building this if we don't need it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Require a minimum 16x16 size for the scanout, to make sure the guest
can't set either width or height to zero. This (a) doesn't make sense
at all and (b) causes problems in some UI code. When using spice this
will triggers an assert().
Reported-by: Tyler Slabinski <tslabinski@slabity.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190527091226.4943-1-kraxel@redhat.com
This tests boot a full VM and check the serial console until
the SSH daemon is running, then start a SSH session and run
some commands.
This test can be run using:
$ avocado --show=ssh run -t arch:mips tests/acceptance/linux_ssh_mips_malta.py
ssh: Entering interactive session.
ssh: # uname -a
ssh: Linux debian-mips 3.2.0-4-4kc-malta #1 Debian 3.2.51-1 mips GNU/Linux
ssh: # lspci -d 11ab:4620
ssh: 00:00.0 Host bridge: Marvell Technology Group Ltd. GT-64120/64120A/64121A System Controller (rev 10)
ssh: # cat /sys/bus/i2c/devices/i2c-0/name
ssh: SMBus PIIX4 adapter at 1100
ssh: # cat /proc/mtd
ssh: dev: size erasesize name
ssh: mtd0: 00100000 00010000 "YAMON"
ssh: mtd1: 002e0000 00010000 "User FS"
ssh: mtd2: 00020000 00010000 "Board Config"
ssh: # md5sum /dev/mtd2ro
ssh: 0dfbe8aa4c20b52e1b8bf3cb6cbdf193 /dev/mtd2ro
ssh: # poweroff
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190523161832.22490-5-f4bug@amsat.org>
Realign comments to fix warnings issued by checkpatc.pl tool
"WARNING: Block comments use a leading /* on a separate line"
within "target/mips/cpu.h" file.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190413202818.13622-3-jbi.octave@gmail.com>
Add or remove space to fix errors issued by checkpatch.pl tool
"ERROR: spaces required around that..."
"ERROR: space required after that..."
"ERROR: space required before the open parenthesis"
"ERROR: space required after that..."
"ERROR: space prohibited between function name and open parenthesis"
"ERROR: code indent should never use tabs"
"ERROR: line over 90 characters"
within "target/mips/cpu.h" file.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190413202818.13622-2-jbi.octave@gmail.com>
In current code, __NR_msgrcv and__NR_semtimedop are supposed to be
defined if __NR_msgsnd is defined.
But linux headers 5.2-rc1 for MIPS define __NR_msgsnd without defining
__NR_semtimedop and it breaks the QEMU build.
__NR_semtimedop is defined in asm-mips/unistd_n64.h and asm-mips/unistd_n32.h
but not in asm-mips/unistd_o32.h.
Commit d9cb433615 ("linux headers: update against Linux 5.2-rc1") has
updated asm-mips/unistd_o32.h and added __NR_msgsnd but not __NR_semtimedop.
It introduces __NR_semtimedop_time64 instead.
This patch fixes the problem by checking for each __NR_XXX symbol
before defining the corresponding syscall.
Fixes: d9cb433615 ("linux headers: update against Linux 5.2-rc1")
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190523175413.14448-1-laurent@vivier.eu>
This commit addresses QEMU Bug #1825311:
mips_cpu_handle_mmu_fault renders all accessed pages executable
It allows finer-grained control over whether the accessed page should
be executable by moving the decision to the underlying map_address
function, which has more information for this.
As a result, pages that have the XI bit set in the TLB and are accessed
for read/write, don't suddenly end up being executable.
Fixes: https://bugs.launchpad.net/qemu/+bug/1825311
Fixes: 2fb58b7374 ('target-mips: add RI and XI fields to TLB entry')
Signed-off-by: Jakub Jermář <jakub.jermar@kernkonzept.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190517123533.868479-1-jakub.jermar@kernkonzept.com>
The old version of the helper for the INSERT.<B|H|W|D> MSA instructions
has been replaced with four helpers that don't use switch, and change
the endianness of the given index, when executed on a big endian host.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554212605-16457-6-git-send-email-mateja.marjanovic@rt-rk.com>
The old version of the helper for the COPY_U.<B|H|W> MSA instructions
has been replaced with four helpers that don't use switch, and change
the endianness of the given index, when executed on a big endian host.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554212605-16457-5-git-send-email-mateja.marjanovic@rt-rk.com>
The old version of the helper for the COPY_S.<B|H|W|D> MSA instructions
has been replaced with four helpers that don't use switch, and change
the endianness of the given index, when executed on a big endian host.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554212605-16457-4-git-send-email-mateja.marjanovic@rt-rk.com>
Fix the case when the host is a big endian machine, and change
the approach toward ST.<B|H|W|D> instruction helpers.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554212605-16457-3-git-send-email-mateja.marjanovic@rt-rk.com>
Fix the case when the host is a big endian machine, and change
the approach toward LD.<B|H|W|D> instruction helpers.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554212605-16457-2-git-send-email-mateja.marjanovic@rt-rk.com>
MSA instructions MOD_<U|S>.<B|H|W|D> when dividing by zero,
didn't return the same value when executed on a referent hardware
(FPGA MIPS 64 r6, little endian) and when executed on QEMU, which
is not a real bug, because the result when dividing by zero is
UNPREDICTABLE [1] (page 255, 256).
[1] MIPS Architecture for Programmers
Volume IV-j: The MIPS64 SIMD
Architecture Module, Revision 1.12
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554207110-9113-3-git-send-email-mateja.marjanovic@rt-rk.com>
MSA instructions DIV_<U|S>.<B|H|W|D> when dividing by zero,
didn't return the same value when executed on a referent hardware
(FPGA MIPS 64 r6, little endian) and when executed on QEMU, which
is not a real bug, because the result when dividing by zero is
UNPREDICTABLE [1] (page 141, 142).
[1] MIPS Architecture for Programmers
Volume IV-j: The MIPS64 SIMD
Architecture Module, Revision 1.12
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1554207110-9113-2-git-send-email-mateja.marjanovic@rt-rk.com>
There is an analogous change for ARM here:
https://patchwork.kernel.org/patch/10649857
Signed-off-by: Jonathan Behrens <jonathan@fintelia.io>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
According to the spec, "All bits besides SSIP, USIP, and UEIP in the sip
register are read-only." Further, if an interrupt is not delegated to mode x,
then "the corresponding bits in xip [...] should appear to be hardwired to
zero. This patch implements both of those requirements.
Signed-off-by: Jonathan Behrens <jonathan@fintelia.io>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
C.ADDI16SP, C.LWSP, C.JR, C.ADDIW, C.LDSP all have reserved
operands that were not diagnosed.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
No functional change, just making the code easier to read.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The requirement of holding the iothread_mutex is burdersome when
swapping the background and foreground registers in the Hypervisor
extension. To avoid the requrirement let's set the interrupt
asynchronously.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a generic spike machine (not tied to a version) and deprecate the
spike mahines that are tied to a specific version. As we can now specify
the CPU via the command line we no londer need specific versions of the
spike machines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These can now be specified via the command line so we no longer need
these.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At the same time deprecate the ISA string CPUs.
It is dobtful anyone specifies the CPUs, but we are keeping them for the
Spike machine (which is about to be depreated) so we may as well just
mark them as deprecated.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These extra spaces make the "-d op" dump look weird.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The tcg_gen_fooi_tl functions have some immediate constant
folding built in, which match up with some of the riscv asm
builtin macros, like mv and not.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This eliminates all functions in insn_trans/trans_rvc.inc.c,
so the entire file can be removed.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This eliminates about half of the complicated decode
bits within insn_trans/trans_rvc.inc.c.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Special handling for IMM==0 is the only difference between
RVC shifti and RVI shifti. This can be handled with !function.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In some cases this allows us to directly use the insn32
translator function. In some cases we still need a shim.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The generated functions are only used within translate.c
and do not need to be global, or declared.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch introduces wrappers around the tcg_gen_exit_tb() and
tcg_gen_lookup_and_goto_ptr() functions that handle single stepping,
i.e. call gen_exception_debug() when single stepping is enabled.
Theses functions are then used instead of the originals, bringing single
stepping handling in places where it was previously ignored such as jalr
and system branch instructions (ecall, mret, sret, etc.).
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The 'sfence.vma' instruction is privileged, and should only ever be allowed
when executing in supervisor mode or higher.
Signed-off-by: Jonathan Behrens <fintelia@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
QEMU model of the GPIO device on the SiFive E300 series SOCs.
The pins are not used by a board definition yet, however this
implementation can already be used to trigger GPIO interrupts from the
software by configuring a pin as both output and input.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let NVIC adopt the SysTick timer.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-17-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let the MPS2 boards adopt the cpu core, the FPGA and the SCC children.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-16-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-15-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(then manually modified to use numbered IPI name)
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let the SoC adopt the IPI children.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-14-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The Inter Processor Interrupt is a block part of the SoC, not the
"machine" (See Zynq UltraScale+ Device TRM UG1085, "Platform
Management Unit", Power Domains and Islands).
Move the IPI management from the machine to the SoC.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-13-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The Inter Processor Interrupt is a block part of the SoC, not the
"machine" (talking about machine is borderline with the PMU, since
it is embedded into the ZynqMP SoC, but currentl QEMU doesn't
support multi-arch cores).
Move the IPI state to the SoC state, this will simplify the review
of the next patch.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-12-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let the Malta/Boston machines adopt the CPS child, and similarly
the CPS adopts the ITU/CPC/GIC/GCR children.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-11-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
