Enable it by default for the sparc64-softmmu configuration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
The Aspeed SoCs have a different definition of the end of the ring
buffer bit. Add a property to specify which set of bits should be used
by the NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The FTGMAC100 device is an Ethernet controller with DMA function that
can be found on Aspeed SoCs (which include NCSI).
It is fully compliant with IEEE 802.3 specification for 10/100 Mbps
Ethernet and IEEE 802.3z specification for 1000 Mbps Ethernet and
includes Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) interfaces. It adopts an
AHB bus interface and integrates a link list DMA engine with direct
M-Bus accesses for transmitting and receiving packets. It has
independent TX/RX fifos, supports half and full duplex (1000 Mbps mode
only supports full duplex), flow control for full duplex and
backpressure for half duplex.
The FTGMAC100 also implements IP, TCP, UDP checksum offloads and
supports IEEE 802.1Q VLAN tag insertion and removal. It offers
high-priority transmit queue for QoS and CoS applications
This model is backed with a RealTek 8211E PHY which is the chip found
on the AST2500 EVB. It is complete enough to satisfy two different
Linux drivers and a U-Boot driver. Not supported features are :
- IEEE 802.1Q VLAN
- High Priority Transmit Queue
- Wake-On-LAN functions
The code is based on the Coldfire Fast Ethernet Controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds comments on the Basic mode control and status registers bit
definitions. It also adds a couple of bits for 1000BASE-T and the
RealTek 8211E PHY for the FTGMAC100 model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Expose the Cadence GEM revision as a property.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 541324373cf87b50f8be0439a0cb89f5028b016f.1491947224.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM hardware allows incoming data to be 'screened' based on some
register values. Add support for these screens.
We also need to increase the max regs to avoid compilation failures. These new
registers are implemented in the next patch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 73e69a8ad9fa2763e9f68f71eaf2469dd5744fcc.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM hardware supports N number priority queues, this patch is a
step towards that by adding the property to set the queues. At the moment
behaviour doesn't change as we only use queue 0.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 6543ec0d0c4bfd2678d0ed683efb197e91b17733.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The ENET device (present in i.MX6) is "derived" from FEC and backward
compatible with it.
This patch adds the necessary support of the added feature in the ENET
device to allow Linux to use it (on supported processors).
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is to prepare for the ENET Gb device of the i.MX6.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is based on mcf_fec.c FEC implementation for Coldfire
* A generic PHY was added (borrowwed from LAN9118)
* The buffer management is also modified as buffers are
slightly different between Coldfire and i.MX
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: fb314f8a120aa49f8f6ad886f312c649b484fb5a.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux fec driver needs at least basic phy support to probe and work.
The current qemu mcf_fec emulation has no support for the reading or
writing of the MDIO lines to access an attached phy.
This code adds a very simple set of register results for a fixed phy
setup - very similar to that used on an m5208evb board. This is enough
to probe and identify an emulated attached phy.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-4-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a base set of bit definitions for the standard MII phy "Auto-Negotiation
Link Partner Ability Register" (ANLPAR).
The original definitions moved into mii.h from the allwinner_emac driver
did not define these.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-3-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a common set of definitions of address and register values for
ethernet MII phys. A few of the current ethernet drivers have at least
a partial set of these definitions. Others just use hard coded raw
constant numbers.
This initial set is copied directly from the allwinner_emac code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-2-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a new header for Cadence GEM to allow using the device with
modern SoC programming conventions. The state struct needs to be
visible to embed the device in SoC containers.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: a98b5df6440c5bff8f813a26bb53ce1cfefb4c4c.1431381507.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for the Fast Ethernet MAC found on Allwinner
SoCs, together with a basic emulation of Realtek RTL8201CP PHY.
Since there is no public documentation of the Allwinner controller, the
implementation is based on Linux kernel driver.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
