In VFIO migration resume phase and some guest startups, there are
already unmasked vectors in the vector table when calling
vfio_msix_enable(). So in order to avoid inefficiently disabling
and enabling vectors repeatedly, let's allocate all needed vectors
first and then enable these unmasked vectors one by one without
disabling.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Message-Id: <20210310030233.1133-4-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In the VFIO VM state change handler when stopping the VM, the _RUNNING
bit in device_state is cleared which makes the VFIO device stop, including
no longer generating interrupts. Then we can save the pending states of
all interrupts in the GIC VM state change handler (on ARM).
So we have to set the priority of the VFIO VM state change handler
explicitly (like virtio devices) to ensure it is called before the
GIC's in saving.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210310030233.1133-3-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On ARM64 the VFIO SET_IRQS ioctl is dependent on the VM interrupt
setup, if the restoring of the VFIO PCI device config space is
before the VGIC, an error might occur in the kernel.
So we move the saving of the config space to the non-iterable
process, thus it will be called after the VGIC according to
their priorities.
As for the possible dependence of the device specific migration
data on it's config space, we can let the vendor driver to
include any config info it needs in its own data stream.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Message-Id: <20210310030233.1133-2-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In an attempt to fix smmu/virtio-iommu - vhost regression, commit
958ec334bc ("vhost: Unbreak SMMU and virtio-iommu on dev-iotlb support")
broke virtio-iommu integration. This is due to the fact VFIO registers
IOMMU_NOTIFIER_ALL notifiers, which includes IOMMU_NOTIFIER_DEVIOTLB_UNMAP
and this latter now is rejected by the virtio-iommu. As a consequence,
the registration fails. VHOST behaves like a device with an ATC cache. The
VFIO device does not support this scheme yet.
Let's register only legacy MAP and UNMAP notifiers.
Fixes: 958ec334bc ("vhost: Unbreak SMMU and virtio-iommu on dev-iotlb support")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210209213233.40985-2-eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the word "blacklist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210205171817.2108907-9-philmd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is an obvious typo in the function name of the .log_sync() callback.
Spell it correctly.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-Id: <20201204014240.772-1-yuzenghui@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A pwrite() call returns the number of bytes written (or -1 on error),
and vfio-ccw compares this number with the size of the region to
determine if an error had occurred or not.
If they are not equal, this is a failure and the errno is used to
determine exactly how things failed. An errno of zero is possible
(though unlikely) in this situation and would be translated to a
successful operation.
If they ARE equal, the ret_code field is read from the region to
determine how to proceed. While the kernel sets the ret_code field
as necessary, the region and thus this field is not "written back"
to the user. So the value can only be what it was initialized to,
which is zero.
So, let's convert an unexpected length with errno of zero to a
return code of -EFAULT, and explicitly set an expected length to
a return code of zero. This will be a little safer and clearer.
Suggested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210303160739.2179378-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Those flags can be used to express different requirements for the
display or other needs.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-12-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Now that the vfio-ccw code has a notifier interface to request that
a device be unplugged, let's wire that together.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210104202057.48048-4-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
The function will be moved to common QOM code, as it is not
specific to TYPE_DEVICE anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every single qdev property setter function manually checks
dev->realized. We can just check dev->realized inside
qdev_property_set() instead.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-10-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
By default dirty pages tracking is enabled during iterative phase
(pre-copy phase).
Added per device opt-out option 'x-pre-copy-dirty-page-tracking' to
disable dirty pages tracking during iterative phase. If the option
'x-pre-copy-dirty-page-tracking=off' is set for any VFIO device, dirty
pages tracking during iterative phase will be disabled.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Support for migration of vfio devices is still in flux. Developers
are attempting to add support for new devices and new architectures,
but none are yet readily available for validation. We have concerns
whether we're transferring device resources at the right point in the
migration, whether we're guaranteeing that updates during pre-copy are
migrated, and whether we can provide bit-stream compatibility should
any of this change. Even the question of whether devices should
participate in dirty page tracking during pre-copy seems contentious.
In short, migration support has not had enough soak time and it feels
premature to mark it as supported.
Create an experimental option such that we can continue to develop.
[Retaining previous acks/reviews for a previously identical code
change with different specifics in the commit log.]
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fix also a similar typo in a code comment.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20201117193448.393472-1-sw@weilnetz.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
IOMMUs may declare memory regions spanning from 0 to UINT64_MAX. When
attempting to deal with such region, vfio_listener_region_del() passes a
size of 2^64 to int128_get64() which throws an assertion failure. Even
ignoring this, the VFIO_IOMMU_DMA_MAP ioctl cannot handle this size
since the size field is 64-bit. Split the request in two.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-11-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set IOMMU supported page size mask same as host Linux supported page
size mask.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-9-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The type of input variable is unsigned int
while the printer type is int. So fix incorrect print type.
Signed-off-by: Zhengui li <lizhengui@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that VFIO_DEVICE_GET_INFO supports capability chains, add a helper
function to find specific capabilities in the chain.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The underlying host may be limiting the number of outstanding DMA
requests for type 1 IOMMU. Add helper functions to check for the
DMA available capability and retrieve the current number of DMA
mappings allowed.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: vfio_get_info_dma_avail moved inside CONFIG_LINUX]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rather than duplicating the same loop in multiple locations,
create a static function to do the work.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added amount of bytes transferred to the VM at destination by all VFIO
devices
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If the device is not a failover primary device, call
vfio_migration_probe() and vfio_migration_finalize() to enable
migration support for those devices that support it respectively to
tear it down again.
Removed migration blocker from VFIO PCI device specific structure and use
migration blocker from generic structure of VFIO device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With vIOMMU, IO virtual address range can get unmapped while in pre-copy
phase of migration. In that case, unmap ioctl should return pages pinned
in that range and QEMU should find its correcponding guest physical
addresses and report those dirty.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
[aw: fix error_report types, fix cpu_physical_memory_set_dirty_lebitmap() cast]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When vIOMMU is enabled, register MAP notifier from log_sync when all
devices in container are in stop and copy phase of migration. Call replay
and get dirty pages from notifier callback.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio_listener_log_sync gets list of dirty pages from container using
VFIO_IOMMU_GET_DIRTY_BITMAP ioctl and mark those pages dirty when all
devices are stopped and saving state.
Return early for the RAM block section of mapped MMIO region.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
[aw: fix error_report types, fix cpu_physical_memory_set_dirty_lebitmap() cast]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Call VFIO_IOMMU_DIRTY_PAGES ioctl to start and stop dirty pages tracking
for VFIO devices.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added helper functions to get IOMMU info capability chain.
Added function to get migration capability information from that
capability chain for IOMMU container.
Similar change was proposed earlier:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg03759.html
Disable migration for devices if IOMMU module doesn't support migration
capability.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Sequence during _RESUMING device state:
While data for this device is available, repeat below steps:
a. read data_offset from where user application should write data.
b. write data of data_size to migration region from data_offset.
c. write data_size which indicates vendor driver that data is written in
staging buffer.
For user, data is opaque. User should write data in the same order as
received.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added .save_live_pending, .save_live_iterate and .save_live_complete_precopy
functions. These functions handles pre-copy and stop-and-copy phase.
In _SAVING|_RUNNING device state or pre-copy phase:
- read pending_bytes. If pending_bytes > 0, go through below steps.
- read data_offset - indicates kernel driver to write data to staging
buffer.
- read data_size - amount of data in bytes written by vendor driver in
migration region.
- read data_size bytes of data from data_offset in the migration region.
- Write data packet to file stream as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data,
VFIO_MIG_FLAG_END_OF_STATE }
In _SAVING device state or stop-and-copy phase
a. read config space of device and save to migration file stream. This
doesn't need to be from vendor driver. Any other special config state
from driver can be saved as data in following iteration.
b. read pending_bytes. If pending_bytes > 0, go through below steps.
c. read data_offset - indicates kernel driver to write data to staging
buffer.
d. read data_size - amount of data in bytes written by vendor driver in
migration region.
e. read data_size bytes of data from data_offset in the migration region.
f. Write data packet as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data}
g. iterate through steps b to f while (pending_bytes > 0)
h. Write {VFIO_MIG_FLAG_END_OF_STATE}
When data region is mapped, its user's responsibility to read data from
data_offset of data_size before moving to next steps.
Added fix suggested by Artem Polyakov to reset pending_bytes in
vfio_save_iterate().
Added fix suggested by Zhi Wang to add 0 as data size in migration stream and
add END_OF_STATE delimiter to indicate phase complete.
Suggested-by: Artem Polyakov <artemp@nvidia.com>
Suggested-by: Zhi Wang <zhi.wang.linux@gmail.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Define flags to be used as delimiter in migration stream for VFIO devices.
Added .save_setup and .save_cleanup functions. Map & unmap migration
region from these functions at source during saving or pre-copy phase.
Set VFIO device state depending on VM's state. During live migration, VM is
running when .save_setup is called, _SAVING | _RUNNING state is set for VFIO
device. During save-restore, VM is paused, _SAVING state is set for VFIO device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added migration state change notifier to get notification on migration state
change. These states are translated to VFIO device state and conveyed to
vendor driver.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VM state change handler is called on change in VM's state. Based on
VM state, VFIO device state should be changed.
Added read/write helper functions for migration region.
Added function to set device_state.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: lx -> HWADDR_PRIx, remove redundant parens]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Whether the VFIO device supports migration or not is decided based of
migration region query. If migration region query is successful and migration
region initialization is successful then migration is supported else
migration is blocked.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added functions to save and restore PCI device specific data,
specifically config space of PCI device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This function will be used for migration region.
Migration region is mmaped when migration starts and will be unmapped when
migration is complete.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio_get_dev_region_info() unconditionally allocates memory
for a passed-in vfio_region_info structure (and does not re-use
an already allocated structure). Therefore, we have to free
the structure we pass to that function in vfio_ccw_get_region()
for every region we successfully obtained information for.
Fixes: 8fadea24de ("vfio-ccw: support async command subregion")
Fixes: 46ea3841ed ("vfio-ccw: Add support for the schib region")
Fixes: f030532f2a ("vfio-ccw: Add support for the CRW region and IRQ")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200928101701.13540-1-cohuck@redhat.com>
We want to introduce a new version of qemu_open() that uses an Error
object for reporting problems and make this it the preferred interface.
Rename the existing method to release the namespace for the new impl.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200902224311.1321159-56-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200902224311.1321159-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200902224311.1321159-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of scripts/cleanup-trace-events.pl. Funnies
requiring manual post-processing:
* accel/tcg/cputlb.c trace points are in trace-events.
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to
guard debug code.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* linux-user/trace-events abbreviates a tedious list of filenames to
*/signal.c.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200806141334.3646302-5-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-43-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calling ramfb_display_update() might replace the DisplaySurface with the
boot display, which in turn will free the currently active
DisplaySurface.
So clear our DisplaySurface pinter (dpy->region.surface pointer) to (a)
avoid use-after-free and (b) force replacing the boot display with the
real display when switching back.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 20200713124520.23266-1-kraxel@redhat.com
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. The previous commit did that with a Coccinelle script I
consider fairly trustworthy. This commit uses the same script with
the matching of return taken out, i.e. we convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
}
to
if (!foo(..., errp)) {
...
...
}
This is unsound: @err could still be read between afterwards. I don't
know how to express "no read of @err without an intervening write" in
Coccinelle. Instead, I manually double-checked for uses of @err.
Suboptimal line breaks tweaked manually. qdev_realize() simplified
further to placate scripts/checkpatch.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-36-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
VFIO is (except devices without a physical IOMMU or some mediated devices)
incompatible with discarding of RAM. The kernel will pin basically all VM
memory. Let's convert to ram_block_discard_disable(), which can now
fail, in contrast to qemu_balloon_inhibit().
Leave "x-balloon-allowed" named as it is for now.
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Tony Krowiak <akrowiak@linux.ibm.com>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: Eric Farman <farman@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The crw region can be used to obtain information about
Channel Report Words (CRW) from vfio-ccw driver.
Currently only channel-path related CRWs are passed to
QEMU from vfio-ccw driver.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505125757.98209-7-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Make it easier to add new ones in the future.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505125757.98209-5-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The schib region can be used to obtain the latest SCHIB from the host
passthrough subchannel. Since the guest SCHIB is virtualized,
we currently only update the path related information so that the
guest is aware of any path related changes when it issues the
'stsch' instruction.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505125757.98209-4-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
While we're at it, add a g_free() for the async_cmd_region that
is the last thing currently created. g_free() knows how to handle
NULL pointers, so this makes it easier to remember what cleanups
need to be performed when new regions are added.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505125757.98209-3-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The #ifdef CONFIG_VFIO_IGD in pci-quirks.c is not working since the
required header config-devices.h is not included, so that the legacy
IGD passthrough is currently broken. Let's include the right header
to fix this issue.
Buglink: https://bugs.launchpad.net/qemu/+bug/1882784
Fixes: 29d62771c8 ("hw/vfio: Move the IGD quirk code to a separate file")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The VMD endpoint provides a real PCIe domain to the guest, including
bridges and endpoints. Because the VMD domain is enumerated by the guest
kernel, the guest kernel will assign Guest Physical Addresses to the
downstream endpoint BARs and bridge windows.
When the guest kernel performs MMIO to VMD sub-devices, MMU will
translate from the guest address space to the physical address space.
Because the bridges have been programmed with guest addresses, the
bridges will reject the transaction containing physical addresses.
VMD device 28C0 natively assists passthrough by providing the Host
Physical Address in shadow registers accessible to the guest for bridge
window assignment. The shadow registers are valid if bit 1 is set in VMD
VMLOCK config register 0x70.
In order to support existing VMDs, this quirk provides the shadow
registers in a vendor-specific PCI capability to the vfio-passthrough
device for all VMD device ids which don't natively assist with
passthrough. The Linux VMD driver is updated to check for this new
vendor-specific capability.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIO is currently the only one left that is not using the generic
function (kvm_irqchip_add_irqfd_notifier_gsi()) to register irqfds.
Let VFIO use the common framework too.
Follow up patches will introduce extra features for kvm irqfd, so that
VFIO can easily leverage that after the switch.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200318145204.74483-3-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the explicit prefetch check when using vfio-ccw devices.
This check does not trigger in practice as all Linux channel programs
are intended to use prefetch.
Newer Linux kernel versions do not require to force the PFCH flag with
vfio-ccw devices anymore.
Signed-off-by: Jared Rossi <jrossi@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20200512181535.18630-2-jrossi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If SELinux is setup without 'execmem' permission for qemu, all mmap
with (PROT_WRITE | PROT_EXEC) will fail and print a warning in
SELinux log.
If "nvlink2-mr" memory allocation fails (fist diff), it will cause
guest NUMA nodes to not be correctly configured (V100 memory will
not be visible for guest, nor its NUMA nodes).
Not having 'execmem' permission is intesting for virtual machines to
avoid buffer-overflow based attacks, and it's adopted in distros
like RHEL.
So, removing the PROT_EXEC flag seems the right thing to do.
Browsing some other code that mmaps memory for usage with
memory_region_init_ram_device_ptr, I could notice it's usual to
not have PROT_EXEC (only PROT_READ | PROT_WRITE), so it should be
no problem around this.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Message-Id: <20200501055448.286518-1-leobras.c@gmail.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit f79081b4b7.
Patch has broken byteorder handling: RAMFBCfg fields are in bigendian
byteorder, the reset function doesn't care so native byteorder is used
instead. Given this went unnoticed so far the feature is obviously
unused, so just revert the patch.
Cc: Hou Qiming <hqm03ster@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20200429115236.28709-2-kraxel@redhat.com
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
- ran regexp "qemu_mutex_lock\(.*\).*\n.*if" to find targets
- replaced result with QEMU_LOCK_GUARD if all unlocks at function end
- replaced result with WITH_QEMU_LOCK_GUARD if unlock not at end
Signed-off-by: Daniel Brodsky <dnbrdsky@gmail.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 20200404042108.389635-3-dnbrdsky@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Coverity detected an issue (CID 1421903) with potential call of clz64(0)
which returns 64 which make it do "<<" with a negative number.
This checks the mask and avoids undefined behaviour.
In practice pgsizes and memory_region_iommu_get_min_page_size() always
have some common page sizes and even if they did not, the resulting page
size would be 0x8000.0000.0000.0000 (gcc 9.2) and
ioctl(VFIO_IOMMU_SPAPR_TCE_CREATE) would fail anyway.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20200324063912.25063-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fixes: 8b818e059b
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200218094402.26625-9-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In a few places we report errno formatted as a negative integer.
This is not as user friendly as it can be. Use strerror() and/or
error_setg_errno() instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <4949c3ecf1a32189b8a4b5eb4b0fd04c1122501d.1581674006.git.mprivozn@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The IGD quirk code defines a separate device, the so-called
"vfio-pci-igd-lpc-bridge" which shows up as a user-creatable
device in all QEMU binaries that include the vfio code. This
is a little bit unfortunate for two reasons: First, this device
is completely useless in binaries like qemu-system-s390x.
Second we also would like to disable it in downstream RHEL
which currently requires some extra patches there since the
device does not have a proper Kconfig-style switch yet.
So it would be good if the device could be disabled more easily,
thus let's move the code to a separate file instead and introduce
a proper Kconfig switch for it which gets only enabled by default
if we also have CONFIG_PC_PCI enabled.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The kvm irqchip notifier is only registered if the device supports
INTx, however it's unconditionally removed. If the assigned device
does not support INTx, this will cause QEMU to crash when unplugging
the device from the system. Change it to conditionally remove the
notifier only if the notify hook is setup.
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v4.2
Reported-by: yanghliu@redhat.com
Debugged-by: Eduardo Habkost <ehabkost@redhat.com>
Fixes: c5478fea27 ("vfio/pci: Respond to KVM irqchip change notifier")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1782678
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
No reason for local_err here, use errp directly instead.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191205174635.18758-21-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
VFIO PCI devices already respond to the pci intx routing notifier, in order
to update kernel irqchip mappings when routing is updated. However this
won't handle the case where the irqchip itself is replaced by a different
model while retaining the same routing. This case can happen on
the pseries machine type due to PAPR feature negotiation.
To handle that case, add a handler for the irqchip change notifier, which
does much the same thing as the routing notifier, but is unconditional,
rather than being a no-op when the routing hasn't changed.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
This splits the vfio_intx_update() function into one part doing the actual
reconnection with the KVM irqchip (vfio_intx_update(), now taking an
argument with the new routing) and vfio_intx_routing_notifier() which
handles calls to the pci device intx routing notifier and calling
vfio_intx_update() when necessary. This will make adding support for the
irqchip change notifier easier.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
hw/vfio/display.c needs the EDID subsystem, select it.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When an error occurs in migrate_add_blocker() it sets a
negative return value and uses error pointer we pass in.
Instead of just looking at the error pointer check for a negative return
value and avoid a coverity error because the return value is
set but never used. This fixes CID 1407219.
Reported-by: Coverity (CID 1407219)
Fixes: f045a0104c ("vfio: unplug failover primary device before migration")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When user tries to hotplug a VFIO device, but the operation fails
somewhere in the middle (in my testing it failed because of
RLIMIT_MEMLOCK forbidding more memory allocation), then a double
free occurs. In vfio_realize() the vdev->migration_blocker is
allocated, then something goes wrong which causes control to jump
onto 'error' label where the error is freed. But the pointer is
left pointing to invalid memory. Later, when
vfio_instance_finalize() is called, the memory is freed again.
In my testing the second hunk was sufficient to fix the bug, but
I figured the first hunk doesn't hurt either.
==169952== Invalid read of size 8
==169952== at 0xA47DCD: error_free (error.c:266)
==169952== by 0x4E0A18: vfio_instance_finalize (pci.c:3040)
==169952== by 0x8DF74C: object_deinit (object.c:606)
==169952== by 0x8DF7BE: object_finalize (object.c:620)
==169952== by 0x8E0757: object_unref (object.c:1074)
==169952== by 0x45079C: memory_region_unref (memory.c:1779)
==169952== by 0x45376B: do_address_space_destroy (memory.c:2793)
==169952== by 0xA5C600: call_rcu_thread (rcu.c:283)
==169952== by 0xA427CB: qemu_thread_start (qemu-thread-posix.c:519)
==169952== by 0x80A8457: start_thread (in /lib64/libpthread-2.29.so)
==169952== by 0x81C96EE: clone (in /lib64/libc-2.29.so)
==169952== Address 0x143137e0 is 0 bytes inside a block of size 48 free'd
==169952== at 0x4A342BB: free (vg_replace_malloc.c:530)
==169952== by 0xA47E05: error_free (error.c:270)
==169952== by 0x4E0945: vfio_realize (pci.c:3025)
==169952== by 0x76A4FF: pci_qdev_realize (pci.c:2099)
==169952== by 0x689B9A: device_set_realized (qdev.c:876)
==169952== by 0x8E2C80: property_set_bool (object.c:2080)
==169952== by 0x8E0EF6: object_property_set (object.c:1272)
==169952== by 0x8E3FC8: object_property_set_qobject (qom-qobject.c:26)
==169952== by 0x8E11DB: object_property_set_bool (object.c:1338)
==169952== by 0x5E7BDD: qdev_device_add (qdev-monitor.c:673)
==169952== by 0x5E81E5: qmp_device_add (qdev-monitor.c:798)
==169952== by 0x9E18A8: do_qmp_dispatch (qmp-dispatch.c:132)
==169952== Block was alloc'd at
==169952== at 0x4A35476: calloc (vg_replace_malloc.c:752)
==169952== by 0x51B1158: g_malloc0 (in /usr/lib64/libglib-2.0.so.0.6000.6)
==169952== by 0xA47357: error_setv (error.c:61)
==169952== by 0xA475D9: error_setg_internal (error.c:97)
==169952== by 0x4DF8C2: vfio_realize (pci.c:2737)
==169952== by 0x76A4FF: pci_qdev_realize (pci.c:2099)
==169952== by 0x689B9A: device_set_realized (qdev.c:876)
==169952== by 0x8E2C80: property_set_bool (object.c:2080)
==169952== by 0x8E0EF6: object_property_set (object.c:1272)
==169952== by 0x8E3FC8: object_property_set_qobject (qom-qobject.c:26)
==169952== by 0x8E11DB: object_property_set_bool (object.c:1338)
==169952== by 0x5E7BDD: qdev_device_add (qdev-monitor.c:673)
Fixes: f045a0104c ("vfio: unplug failover primary device before migration")
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
As usual block all vfio-pci devices from being migrated, but make an
exception for failover primary devices. This is achieved by setting
unmigratable to 0 but also add a migration blocker for all vfio-pci
devices except failover primary devices. These will be unplugged before
migration happens by the migration handler of the corresponding
virtio-net standby device.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20191029114905.6856-12-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are three page size in qemu:
real host page size
host page size
target page size
All of them have dedicate variable to represent. For the last two, we
use the same form in the whole qemu project, while for the first one we
use two forms: qemu_real_host_page_size and getpagesize().
qemu_real_host_page_size is defined to be a replacement of
getpagesize(), so let it serve the role.
[Note] Not fully tested for some arch or device.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The following guest behaviour patter leads to double free in VFIO PCI:
1. Guest enables MSI interrupts
vfio_msi_enable is called, but fails in vfio_enable_vectors.
In our case this was because VFIO GPU device was in D3 state.
Unhappy path in vfio_msi_enable will g_free(vdev->msi_vectors) but not
set this pointer to NULL
2. Guest still sees MSI an enabled after that because emulated config
write is done in vfio_pci_write_config unconditionally before calling
vfio_msi_enable
3. Guest disables MSI interrupts
vfio_msi_disable is called and tries to g_free(vdev->msi_vectors)
in vfio_msi_disable_common => double free
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently, when a notifier is attempted to be registered and its
flags are not supported (especially the MAP one) by the IOMMU MR,
we generally abruptly exit in the IOMMU code. The failure could be
handled more nicely in the caller and especially in the VFIO code.
So let's allow memory_region_register_iommu_notifier() to fail as
well as notify_flag_changed() callback.
All sites implementing the callback are updated. This patch does
not yet remove the exit(1) in the amd_iommu code.
in SMMUv3 we turn the warning message into an error message saying
that the assigned device would not work properly.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The container error integer field is currently used to store
the first error potentially encountered during any
vfio_listener_region_add() call. However this fails to propagate
detailed error messages up to the vfio_connect_container caller.
Instead of using an integer, let's use an Error handle.
Messages are slightly reworded to accomodate the propagation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Preparation for collapsing the two byte swaps adjust_endianness and
handle_bswap into the former.
Call memory_region_dispatch_{read|write} with endianness encoded into
the "MemOp op" operand.
This patch does not change any behaviour as
memory_region_dispatch_{read|write} is yet to handle the endianness.
Once it does handle endianness, callers with byte swaps can collapse
them into adjust_endianness.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Message-Id: <8066ab3eb037c0388dfadfe53c5118429dd1de3a.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The memory_region_dispatch_{read|write} operand "unsigned size" is
being converted into a "MemOp op".
Convert interfaces by using no-op size_memop.
After all interfaces are converted, size_memop will be implemented
and the memory_region_dispatch_{read|write} operand "unsigned size"
will be converted into a "MemOp op".
As size_memop is a no-op, this patch does not change any behaviour.
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <e70ff5814ac3656974180db6375397c43b0bc8b8.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-20-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
Coverity doesn't like that most callers of vfio_set_irq_signaling() check
the return value and doesn't understand the equivalence of testing the
error pointer instead. Test the return value consistently.
Reported-by: Coverity (CID 1402783)
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <156209642116.14915.9598593247782519613.stgit@gimli.home>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Report an error in case we fail to set a trigger action
on any VFIO_PCI_MSIX_IRQ_INDEX subindex. This might be
useful in debugging a device that is not working properly.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Coverity (CID 1402196)
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
A vfio-ccw device may provide an async command subregion for
issuing halt/clear subchannel requests. If it is present, use
it for sending halt/clear request to the device; if not, fall
back to emulation (as done today).
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <20190613092542.2834-1-cohuck@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Use the new helper.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190617101036.4087-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code used to assign an interrupt index/subindex to an
eventfd is duplicated many times. Let's introduce an helper that
allows to set/unset the signaling for an ACTION_TRIGGER,
ACTION_MASK or ACTION_UNMASK action.
In the error message, we now use errno in case of any
VFIO_DEVICE_SET_IRQS ioctl failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The MSI-X relocation code can sometimes be used to work around bogus
MSI-X capabilities, but this test for whether the PBA is outside of
the specified BAR causes the device to error before we can apply a
relocation. Let it proceed if we intend to relocate MSI-X anyway.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The resizable BAR capability is currently exposed read-only from the
kernel and we don't yet implement a protocol for virtualizing it to
the VM. Exposing it to the guest read-only introduces poor behavior
as the guest has no reason to test that a control register write is
accepted by the hardware. This can lead to cases where the guest OS
assumes the BAR has been resized, but it hasn't. This has been
observed when assigning AMD Vega GPUs.
Note, this does not preclude future enablement of resizable BARs, but
it's currently incorrect to expose this capability as read-only, so
better to not expose it at all.
Reported-by: James Courtier-Dutton <james.dutton@gmail.com>
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Fill the new QemuDmaBuf->modifier field properly from plane info.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 20190529072144.26737-3-kraxel@redhat.com
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190528164020.32250-10-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
If xres / yres were specified in QEMU command line, write them as an initial
resolution to the fw-config space on guest reset, which a later BIOS / OVMF
patch can take advantage of.
Signed-off-by: HOU Qiming <hqm03ster@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-id: 20190513115731.17588-4-marcel.apfelbaum@gmail.com
[fixed malformed patch]
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
'MSIX_CAP_LENGTH' is defined in two .c file. Move it
to hw/pci/msix.h file to reduce duplicated code.
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-5-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'eventd' should be 'eventfd'.
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-4-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's recommended that VMStateDescription names are decoupled from QOM
type names as the latter may freely change without consideration of
migration compatibility.
Link: https://lists.gnu.org/archive/html/qemu-devel/2018-10/msg02175.html
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-3-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The QOMConventions recommends we should use TYPE_FOO
for a TypeInfo's name. Though "vfio-pci-nohotplug" is not
used in other parts, for consistency we should make this change.
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-2-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=RpAK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190426' into staging
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NVIDIA V100 GPUs have on-board RAM which is mapped into the host memory
space and accessible as normal RAM via an NVLink bus. The VFIO-PCI driver
implements special regions for such GPUs and emulates an NVLink bridge.
NVLink2-enabled POWER9 CPUs also provide address translation services
which includes an ATS shootdown (ATSD) register exported via the NVLink
bridge device.
This adds a quirk to VFIO to map the GPU memory and create an MR;
the new MR is stored in a PCI device as a QOM link. The sPAPR PCI uses
this to get the MR and map it to the system address space.
Another quirk does the same for ATSD.
This adds additional steps to sPAPR PHB setup:
1. Search for specific GPUs and NPUs, collect findings in
sPAPRPHBState::nvgpus, manage system address space mappings;
2. Add device-specific properties such as "ibm,npu", "ibm,gpu",
"memory-block", "link-speed" to advertise the NVLink2 function to
the guest;
3. Add "mmio-atsd" to vPHB to advertise the ATSD capability;
4. Add new memory blocks (with extra "linux,memory-usable" to prevent
the guest OS from accessing the new memory until it is onlined) and
npuphb# nodes representing an NPU unit for every vPHB as the GPU driver
uses it for link discovery.
This allocates space for GPU RAM and ATSD like we do for MMIOs by
adding 2 new parameters to the phb_placement() hook. Older machine types
set these to zero.
This puts new memory nodes in a separate NUMA node to as the GPU RAM
needs to be configured equally distant from any other node in the system.
Unlike the host setup which assigns numa ids from 255 downwards, this
adds new NUMA nodes after the user configures nodes or from 1 if none
were configured.
This adds requirement similar to EEH - one IOMMU group per vPHB.
The reason for this is that ATSD registers belong to a physical NPU
so they cannot invalidate translations on GPUs attached to another NPU.
It is guaranteed by the host platform as it does not mix NVLink bridges
or GPUs from different NPU in the same IOMMU group. If more than one
IOMMU group is detected on a vPHB, this disables ATSD support for that
vPHB and prints a warning.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for vfio portions]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190312082103.130561-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tJvv
-----END PGP SIGNATURE-----
Merge tag 's390-ccw-bios-2019-04-12' into s390-next-staging
Support for booting from a vfio-ccw passthrough dasd device
# gpg: Signature made Fri 12 Apr 2019 01:17:03 PM CEST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
* tag 's390-ccw-bios-2019-04-12':
pc-bios/s390: Update firmware images
s390-bios: Use control unit type to find bootable devices
s390-bios: Support booting from real dasd device
s390-bios: Add channel command codes/structs needed for dasd-ipl
s390-bios: Use control unit type to determine boot method
s390-bios: Refactor virtio to run channel programs via cio
s390-bios: Factor finding boot device out of virtio code path
s390-bios: Extend find_dev() for non-virtio devices
s390-bios: cio error handling
s390-bios: Support for running format-0/1 channel programs
s390-bios: ptr2u32 and u32toptr
s390-bios: Map low core memory
s390-bios: Decouple channel i/o logic from virtio
s390-bios: Clean up cio.h
s390-bios: decouple common boot logic from virtio
s390-bios: decouple cio setup from virtio
s390 vfio-ccw: Add bootindex property and IPLB data
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Rename qemu_getrampagesize() to qemu_minrampagesize(). While at it,
properly rename find_max_supported_pagesize() to
find_min_backend_pagesize().
s390x is actually interested into the maximum ram pagesize, so
introduce and use qemu_maxrampagesize().
Add a TODO, indicating that looking at any mapped memory backends is not
100% correct in some cases.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190417113143.5551-3-david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417190641.26814-8-armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Add bootindex property and iplb data for vfio-ccw devices. This allows us to
forward boot information into the bios for vfio-ccw devices.
Refactor s390_get_ccw_device() to return device type. This prevents us from
having to use messy casting logic in several places.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1554388475-18329-2-git-send-email-jjherne@linux.ibm.com>
[thuth: fixed "typedef struct VFIOCCWDevice" build failure with clang]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The GCC 9 compiler complains about many places in s390 code
that take the address of members of the 'struct SCHIB' which
is marked packed:
hw/vfio/ccw.c: In function ‘vfio_ccw_io_notifier_handler’:
hw/vfio/ccw.c:133:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer value \
[-Waddress-of-packed-member]
133 | SCSW *s = &sch->curr_status.scsw;
| ^~~~~~~~~~~~~~~~~~~~~~
hw/vfio/ccw.c:134:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer value \
[-Waddress-of-packed-member]
134 | PMCW *p = &sch->curr_status.pmcw;
| ^~~~~~~~~~~~~~~~~~~~~~
...snip many more...
Almost all of these are just done for convenience to avoid
typing out long variable/field names when referencing struct
members. We can get most of this convenience by taking the
address of the 'struct SCHIB' instead, avoiding triggering
the compiler warnings.
In a couple of places we copy via a local variable which is
a technique already applied elsewhere in s390 code for this
problem.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190329111104.17223-12-berrange@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This makes vfio_get_region_info_cap() to be used in quirks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190307050518.64968-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "systempagesize" name suggests that it is the host system page size
while it is the smallest page size of memory backing the guest RAM so
let's rename it to stop confusion. This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-4-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current code assumes that we can address more bits on a PCI bus
for DMA than we really can but there is no way knowing the actual limit.
This makes a better guess for the number of levels and if the kernel
fails to allocate that, this increases the level numbers till succeeded
or reached the 64bit limit.
This adds levels to the trace point.
This may cause the kernel to warn about failed allocation:
[65122.837458] Failed to allocate a TCE memory, level shift=28
which might happen if MAX_ORDER is not large enough as it can vary:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/Kconfig?h=v5.0-rc2#n727
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Kick the display link up event with a 0.1 sec delay,
so the guest has a chance to notice the link down first.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[update for redefined macro]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This allows configure the display resolution which the vgpu should use.
The information will be passed to the guest using EDID, so the mdev
driver must support the vfio edid region for this to work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds EDID support to the vfio display (aka vgpu) code.
When supported by the mdev driver qemu will generate a EDID blob
and pass it on using the new vfio edid region. The EDID blob will
be updated on UI changes (i.e. window resize), so the guest can
adapt.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[remove control flow via macro, use unsigned format specifier]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
CONFIG_VFIO_PCI was not "default y" - and once you do that, it is also
important to disable it if PCI is not there.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccBqMAAoJECgfDbjSjVRpvSEIAKYPRNdCBX/SSS/L/tmJS5Zt
8IyU/HW1YJ249vO+aT6z4Q3QPgqNC3KjXC3brx/WRoPZnRroen4rv2Kqnk6SayPa
a52d2ubXKWxb3swdG1CAVzFRhq/ABpgAPx0dr1JW+RXgo2lxpJ4GNYxKMosQTaPE
hRNeXl1XlcIK525kJhFH3Hlij9mTRuY6T7ydpPQd8dUq2dBRaL9RrzZRrkZxCy6l
gQPUqNzPhG0XXyOiJmwYyVX0zGzbYrMLrMQAor2SBIYmU+zv2eZGPJUYxoMTUMzt
YR0WCpvkvPITlAryaBoozAIDYVz8PxBRT1KRwpDal+2rzlm6o+veKDiF8R46gn0=
=GzUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, tests
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 22 Feb 2019 15:51:40 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
pci: Sanity test minimum downstream LNKSTA
hw/smbios: fix offset of type 3 sku field
pci: Move NVIDIA vendor id to the rest of ids
virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size
virtio-balloon: Use ram_block_discard_range() instead of raw madvise()
virtio-balloon: Rework ballon_page() interface
virtio-balloon: Corrections to address verification
virtio-balloon: Remove unnecessary MADV_WILLNEED on deflate
i386/kvm: ignore masked irqs when update msi routes
contrib/vhost-user-blk: fix the compilation issue
Revert "contrib/vhost-user-blk: fix the compilation issue"
pc-dimm: use same mechanism for [get|set]_addr
tests/data: introduce "uefi-boot-images" with the "bios-tables-test" ISOs
tests/uefi-test-tools: add build scripts
tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app
roms: build the EfiRom utility from the roms/edk2 submodule
roms: add the edk2 project as a git submodule
vhost-user-test: create a temporary directory per TestServer
vhost-user-test: small changes to init_hugepagefs
vhost-user-test: create a main loop per TestServer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduces hot plug/unplug support for the vfio-ap device.
To hot plug a vfio-ap device using the QEMU device_add command:
(qemu) device_add vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
to which AP resources to be used by the guest have been assigned.
A vfio-ap device can be hot plugged only if:
1. A vfio-ap device has not been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
To hot unplug a vfio-ap device using the QEMU device_del command:
(qemu) device_del vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
specified when the vfio-ap device was attached to the virtual machine's
ap-bus.
A vfio-ap device can be hot unplugged only if:
1. A vfio-ap device has been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
Please note that a hot plug handler is not necessary for the vfio-ap device
because the AP matrix configuration for the guest is performed by the
kernel device driver when the vfio-ap device is realized. The vfio-ap device
represents a VFIO mediated device created in the host sysfs for use by a guest.
The mdev device is configured with an AP matrix (i.e., adapters and domains) via
its sysfs attribute interfaces prior to starting the guest or plugging a vfio-ap
device in. When the device is realized, a file descriptor is opened on the mdev
device which results in a callback to the vfio_ap kernel device driver. The
device driver then configures the AP matrix in the guest's SIE state description
from the AP matrix assigned via the mdev device's sysfs interfaces. The AP
devices will be created for the guest when the AP bus running on the guest
subsequently performs its periodic scan for AP devices.
The qdev_simple_device_unplug_cb() callback function is used for the same
reaons; namely, the vfio_ap kernel device driver will perform the AP resource
de-configuration for the guest when the vfio-ap device is unplugged. When the
vfio-ap device is unrealized, the mdev device file descriptor is closed which
results in a callback to the vfio_ap kernel device driver. The device driver
then clears the AP matrix configuration in the guest's SIE state description
and resets all of the affected queues. The AP devices created for the guest
will be removed when the AP bus running on the guest subsequently performs
its periodic scan and finds there are no longer any AP resources assigned to the
guest.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1550519397-25359-2-git-send-email-akrowiak@linux.ibm.com>
[CH: adapt to changed qbus_set_hotplug_handler() signature]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
sPAPR code will use it too so move it from VFIO to the common code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190214051440.59167-1-aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We introduce the vfio_init_container_type() helper.
It computes the highest usable iommu type and then
set the container and the iommu type.
Its usage in vfio_connect_container() makes the code
ready for addition of new iommu types.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
A kernel bug was introduced in v4.15 via commit 71a7d3d78e3c which
adds a test for address space wrap-around in the vfio DMA unmap path.
Unfortunately due to overflow, the kernel detects an unmap of the last
page in the 64-bit address space as a wrap-around. In QEMU, a Q35
guest with VT-d emulation and guest IOMMU enabled will attempt to make
such an unmap request during VM system reset, triggering an error:
qemu-kvm: VFIO_UNMAP_DMA: -22
qemu-kvm: vfio_dma_unmap(0x561f059948f0, 0xfef00000, 0xffffffff01100000) = -22 (Invalid argument)
Here the IOVA start address (0xfef00000) and the size parameter
(0xffffffff01100000) add to exactly 2^64, triggering the bug. A
kernel fix is queued for the Linux v5.0 release to address this.
This patch implements a workaround to retry the unmap, excluding the
final page of the range when we detect an unmap failing which matches
the requirements for this issue. This is expected to be a safe and
complete workaround as the VT-d address space does not extend to the
full 64-bit space and therefore the last page should never be mapped.
This workaround can be removed once all kernels with this bug are
sufficiently deprecated.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1662291
Reported-by: Pei Zhang <pezhang@redhat.com>
Debugged-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Make hw/vfio configurable and add new CONFIG_VFIO_* to the
default-configs/s390x*-softmmu.mak. This allow a finer-grain
selection of the various VFIO backends.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of wrapping the entire Makefile.objs with an ifeq/endif, just
include the directory only for Linux.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-4-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The '%m' format instructs glibc's printf()/syslog() implementation to
insert the contents of strerror(errno). Since this is a glibc extension
it should generally be avoided in QEMU due to need for portability to a
variety of platforms.
Even though vfio is Linux-only code that could otherwise use "%m", it
must still be avoided in trace-events files because several of the
backends do not use the format string and so this error information is
invisible to them.
The errno string value should be given as an explicit trace argument
instead, making it accessible to all backends. This also allows it to
work correctly with future patches that use the format string with
systemtap's simple printf code.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190123120016.4538-4-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will be needed when we change the QTAILQ head and elem structs
to unions. However, it is also consistent with the usage elsewhere
in QEMU for other list head structs (see for example FsMountList).
Note that most QTAILQs only need their name in order to do backwards
walks. Those do not break with the struct->union change, and anyway
the change will also remove the need to name heads when doing backwards
walks, so those are not touched here.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is not used outside hw/vfio/common.c, so it does not need to
be extern.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG967AAoJECgfDbjSjVRpUlMH/1wy8WW7Br/4JxlWUPsfZTqZ
0Lg2n59wuFzRVS+gLotp6bUaJGR9xn9fKjI1wfD59oVrDTKyauuw82v0OityEs33
ZquFecuJvP6k5N40DkqA9YJjKSw7nUmLrsyrD0t2H43npikP2aD9f6yootrr3oVV
nPwBvyT9ykIBQc7IzsHDiLw3EPdIf+9IR7+l+PLptzV0zK43Jfwi/nzHIQq00UMz
eLM/ejQLIx4BZJnYGS0Cy6v3K7cS3k45LHDY0cGc0id2jHFN2vdQyHCF9I1ps72q
pSlhMaLEwvQSYyre6iFTG5uuvyIPWv3LOkaBEwMSA5B/HXuEb2RKHThYzS9dc68=
=OwW7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, features
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 20 Dec 2018 18:26:03 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (44 commits)
x86-iommu: turn on IR by default if proper
x86-iommu: switch intr_supported to OnOffAuto type
q35: set split kernel irqchip as default
pci: Adjust PCI config limit based on bus topology
spapr_pci: perform unplug via the hotplug handler
pci/shpc: perform unplug via the hotplug handler
pci: Reuse pci-bridge hotplug handler handlers for pcie-pci-bridge
pci/pcie: perform unplug via the hotplug handler
pci/pcihp: perform unplug via the hotplug handler
pci/pcihp: overwrite hotplug handler recursively from the start
pci/pcihp: perform check for bus capability in pre_plug handler
s390x/pci: rename hotplug handler callbacks
pci/shpc: rename hotplug handler callbacks
pci/pcie: rename hotplug handler callbacks
hw/i386: Remove deprecated machines pc-0.10 and pc-0.11
hw: acpi: Remove AcpiRsdpDescriptor and fix tests
hw: acpi: Export and share the ARM RSDP build
hw: arm: Support both legacy and current RSDP build
hw: arm: Convert the RSDP build to the buid_append_foo() API
hw: arm: Carry RSDP specific data through AcpiRsdpData
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181204172535.2799-1-armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
Now that the downstream port will virtually negotiate itself to the
link status of the downstream device, we can remove this emulation.
It's not clear that it was every terribly useful anyway.
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation for reporting higher virtual link speeds and widths,
create enums and macros to help us manage them.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vfio-ap devices do not pin any pages in the host. Therefore, they
are compatible with memory ballooning.
Flag them as compatible, so both vfio-ap and a balloon can be
used simultaneously.
Cc: qemu-stable@nongnu.org
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If ioctl(..., VFIO_DEVICE_RESET) fails, we want to report errno
instead of ret (which is always -1 on error).
Fixes Coverity issue CID 1396176.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The previous commit changed vfio's warning messages from
vfio warning: DEV-NAME: Could not frobnicate
to
warning: vfio DEV-NAME: Could not frobnicate
To match this change, change error messages from
vfio error: DEV-NAME: On fire
to
vfio DEV-NAME: On fire
Note the loss of "error". If we think marking error messages that way
is a good idea, we should mark *all* error messages, i.e. make
error_report() print it.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20181017082702.5581-7-armbru@redhat.com>
The vfio code reports warnings like
error_report(WARN_PREFIX "Could not frobnicate", DEV-NAME);
where WARN_PREFIX is defined so the message comes out as
vfio warning: DEV-NAME: Could not frobnicate
This usage predates the introduction of warn_report() & friends in
commit 97f40301f1. It's time to convert to that interface. Since
these functions already prefix the message with "warning: ", replace
WARN_PREFIX by VFIO_MSG_PREFIX, so the messages come out like
warning: vfio DEV-NAME: Could not frobnicate
The next commit will replace ERR_PREFIX.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-6-armbru@redhat.com>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
Define a TYPE_VFIO_PCI and drop DO_UPCAST.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Up to now the vfio-platform device has been abstract and could not be
instantiated. The integration of a new vfio platform device required
creating a dummy derived device which only set the compatible string.
Following the few vfio-platform device integrations we have seen the
actual requested adaptation happens on device tree node creation
(sysbus-fdt).
Hence remove the abstract setting, and read the list of compatible
values from sysfs if not set by a derived device.
Update the amd-xgbe and calxeda-xgmac drivers to fill in the number of
compatible values, as there can now be more than one.
Note that sysbus-fdt does not support the instantiation of the
vfio-platform device yet.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
[geert: Rebase, set user_creatable=true, use compatible values in sysfs
instead of user-supplied manufacturer/model options, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
So we have a boot display when using a vgpu as primary display.
ramfb depends on a fw_cfg file. fw_cfg files can not be added and
removed at runtime, therefore a ramfb-enabled vfio device can't be
hotplugged.
Add a nohotplug variant of the vfio-pci device (as child class). Add
the ramfb property to the nohotplug variant only. So to enable the vgpu
display with boot support use this:
-device vfio-pci-nohotplug,display=on,ramfb=on,sysfsdev=...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Introduces a VFIO based AP device. The device is defined via
the QEMU command line by specifying:
-device vfio-ap,sysfsdev=<path-to-mediated-matrix-device>
There may be only one vfio-ap device configured for a guest.
The mediated matrix device is created by the VFIO AP device
driver by writing a UUID to a sysfs attribute file (see
docs/vfio-ap.txt). The mediated matrix device will be named
after the UUID. Symbolic links to the $uuid are created in
many places, so the path to the mediated matrix device $uuid
can be specified in any of the following ways:
/sys/devices/vfio_ap/matrix/$uuid
/sys/devices/vfio_ap/matrix/mdev_supported_types/vfio_ap-passthrough/devices/$uuid
/sys/bus/mdev/devices/$uuid
/sys/bus/mdev/drivers/vfio_mdev/$uuid
When the vfio-ap device is realized, it acquires and opens the
VFIO iommu group to which the mediated matrix device is
bound. This causes a VFIO group notification event to be
signaled. The vfio_ap device driver's group notification
handler will get called at which time the device driver
will configure the the AP devices to which the guest will
be granted access.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20181010170309.12045-6-akrowiak@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[CH: added missing g_free and device category]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add two functions to print an error/warning report once depending
on a passed-in condition variable and flip it if printed. This is
useful if you want to print a message not once-globally, but e.g.
once-per-device.
Inspired by warn_once() in hw/vfio/ccw.c, which has been replaced
with warn_report_once_cond().
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20180830145902.27376-2-cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Function comments reworded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
A new error path fails to close the device file descriptor when
triggered by a ballooning incompatibility within the group. Fix it.
Fixes: 238e917285 ("vfio/ccw/pci: Allow devices to opt-in for ballooning")
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fix error reported by Coverity where realpath can return NULL,
resulting in a segfault in strcmp(). This should never happen given
that we're working through regularly structured sysfs paths, but
trivial enough to easily avoid.
Fixes: 238e917285 ("vfio/ccw/pci: Allow devices to opt-in for ballooning")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment the PPC64/pseries guest only supports 4K/64K/16M IOMMU
pages and POWER8 CPU supports the exact same set of page size so
so far things worked fine.
However POWER9 supports different set of sizes - 4K/64K/2M/1G and
the last two - 2M and 1G - are not even allowed in the paravirt interface
(RTAS DDW) so we always end up using 64K IOMMU pages, although we could
back guest's 16MB IOMMU pages with 2MB pages on the host.
This stores the supported host IOMMU page sizes in VFIOContainer and uses
this later when creating a new DMA window. This uses the system page size
(64k normally, 2M/16M/1G if hugepages used) as the upper limit of
the IOMMU pagesize.
This changes the type of @pagesize to uint64_t as this is what
memory_region_iommu_get_min_page_size() returns and clz64() takes.
There should be no behavioral changes on platforms other than pseries.
The guest will keep using the IOMMU page size selected by the PHB pagesize
property as this only changes the underlying hardware TCE table
granularity.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a vfio assigned device makes use of a physical IOMMU, then memory
ballooning is necessarily inhibited due to the page pinning, lack of
page level granularity at the IOMMU, and sufficient notifiers to both
remove the page on balloon inflation and add it back on deflation.
However, not all devices are backed by a physical IOMMU. In the case
of mediated devices, if a vendor driver is well synchronized with the
guest driver, such that only pages actively used by the guest driver
are pinned by the host mdev vendor driver, then there should be no
overlap between pages available for the balloon driver and pages
actively in use by the device. Under these conditions, ballooning
should be safe.
vfio-ccw devices are always mediated devices and always operate under
the constraints above. Therefore we can consider all vfio-ccw devices
as balloon compatible.
The situation is far from straightforward with vfio-pci. These
devices can be physical devices with physical IOMMU backing or
mediated devices where it is unknown whether a physical IOMMU is in
use or whether the vendor driver is well synchronized to the working
set of the guest driver. The safest approach is therefore to assume
all vfio-pci devices are incompatible with ballooning, but allow user
opt-in should they have further insight into mediated devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use a VFIOContainer to associate an AddressSpace to one or more
VFIOGroups. The VFIOContainer represents the DMA context for that
AdressSpace for those VFIOGroups and is synchronized to changes in
that AddressSpace via a MemoryListener. For IOMMU backed devices,
maintaining the DMA context for a VFIOGroup generally involves
pinning a host virtual address in order to create a stable host
physical address and then mapping a translation from the associated
guest physical address to that host physical address into the IOMMU.
While the above maintains the VFIOContainer synchronized to the QEMU
memory API of the VM, memory ballooning occurs outside of that API.
Inflating the memory balloon (ie. cooperatively capturing pages from
the guest for use by the host) simply uses MADV_DONTNEED to "zap"
pages from QEMU's host virtual address space. The page pinning and
IOMMU mapping above remains in place, negating the host's ability to
reuse the page, but the host virtual to host physical mapping of the
page is invalidated outside of QEMU's memory API.
When the balloon is later deflated, attempting to cooperatively
return pages to the guest, the page is simply freed by the guest
balloon driver, allowing it to be used in the guest and incurring a
page fault when that occurs. The page fault maps a new host physical
page backing the existing host virtual address, meanwhile the
VFIOContainer still maintains the translation to the original host
physical address. At this point the guest vCPU and any assigned
devices will map different host physical addresses to the same guest
physical address. Badness.
The IOMMU typically does not have page level granularity with which
it can track this mapping without also incurring inefficiencies in
using page size mappings throughout. MMU notifiers in the host
kernel also provide indicators for invalidating the mapping on
balloon inflation, not for updating the mapping when the balloon is
deflated. For these reasons we assume a default behavior that the
mapping of each VFIOGroup into the VFIOContainer is incompatible
with memory ballooning and increment the balloon inhibitor to match
the attached VFIOGroups.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
PCI devices needing a ROM allocate an optional MemoryRegion with
pci_add_option_rom(). pci_del_option_rom() does the cleanup when the
device is destroyed. The only action taken by this routine is to call
vmstate_unregister_ram() which clears the id string of the optional
ROM RAMBlock and now, also flags the RAMBlock as non-migratable. This
was recently added by commit b895de5027 ("migration: discard
non-migratable RAMBlocks"), .
VFIO devices do their own loading of the PCI option ROM in
vfio_pci_size_rom(). The memory region is switched to an I/O region
and the PCI attribute 'has_rom' is set but the RAMBlock of the ROM
region is not allocated. When the associated PCI device is deleted,
pci_del_option_rom() calls vmstate_unregister_ram() which tries to
flag a NULL RAMBlock, leading to a SEGV.
It seems that 'has_rom' was set to have memory_region_destroy()
called, but since commit 469b046ead ("memory: remove
memory_region_destroy") this is not necessary anymore as the
MemoryRegion is freed automagically.
Remove the PCIDevice 'has_rom' attribute setting in vfio.
Fixes: b895de5027 ("migration: discard non-migratable RAMBlocks")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-38-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is at least one guest (OS) such that although it does not rely on
the guarantees provided by ORB 1 word 9 bit (aka unlimited prefetch, aka
P bit) not being set, it fails to tell this to the machine.
Usually this ain't a big deal, as the original purpose of the P bit is to
allow for performance optimizations. vfio-ccw however can not provide the
guarantees required if the bit is not set.
It is not possible to implement support for the P bit not set without
transitioning to lower level protocols for vfio-ccw. So let's give the
user the opportunity to force setting the P bit, if the user knows this
is safe. For self modifying channel programs forcing the P bit is not
safe. If the P bit is forced for a self modifying channel program things
are expected to break in strange ways.
Let's also avoid warning multiple about P bit not set in the ORB in case
P bit is not told to be forced, and designate the affected vfio-ccw
device.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Acked-by: Jason J. Herne <jjherne@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180524175828.3143-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add support for multiple IOMMU indexes to the IOMMU notifier APIs.
When initializing a notifier with iommu_notifier_init(), the caller
must pass the IOMMU index that it is interested in. When a change
happens, the IOMMU implementation must pass
memory_region_notify_iommu() the IOMMU index that has changed and
that notifiers must be called for.
IOMMUs which support only a single index don't need to change.
Callers which only really support working with IOMMUs with a single
index can use the result of passing MEMTXATTRS_UNSPECIFIED to
memory_region_iommu_attrs_to_index().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-3-peter.maydell@linaro.org
Commit a9994687cb ("vfio/display: core & wireup") added display
support to vfio-pci with the default being "auto", which breaks
existing VMs when the vGPU requires GL support but had no previous
requirement for a GL compatible configuration. "Off" is the safer
default as we impose no new requirements to VM configurations.
Fixes: a9994687cb ("vfio/display: core & wireup")
Cc: qemu-stable@nongnu.org
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With vfio ioeventfd support, we can program vfio-pci to perform a
specified BAR write when an eventfd is triggered. This allows the
KVM ioeventfd to be wired directly to vfio-pci, entirely avoiding
userspace handling for these events. On the same micro-benchmark
where the ioeventfd got us to almost 90% of performance versus
disabling the GeForce quirks, this gets us to within 95%.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The NVIDIA BAR0 quirks virtualize the PCI config space mirrors found
in device MMIO space. Normally PCI config space is considered a slow
path and further optimization is unnecessary, however NVIDIA uses a
register here to enable the MSI interrupt to re-trigger. Exiting to
QEMU for this MSI-ACK handling can therefore rate limit our interrupt
handling. Fortunately the MSI-ACK write is easily detected since the
quirk MemoryRegion otherwise has very few accesses, so simply looking
for consecutive writes with the same data is sufficient, in this case
10 consecutive writes with the same data and size is arbitrarily
chosen. We configure the KVM ioeventfd with data match, so there's
no risk of triggering for the wrong data or size, but we do risk that
pathological driver behavior might consume all of QEMU's file
descriptors, so we cap ourselves to 10 ioeventfds for this purpose.
In support of the above, generic ioeventfd infrastructure is added
for vfio quirks. This automatically initializes an ioeventfd list
per quirk, disables and frees ioeventfds on exit, and allows
ioeventfds marked as dynamic to be dropped on device reset. The
rationale for this latter feature is that useful ioeventfds may
depend on specific driver behavior and since we necessarily place a
cap on our use of ioeventfds, a machine reset is a reasonable point
at which to assume a new driver and re-profile.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Quirks can be self modifying, provide a hook to allow them to cleanup
on device reset if desired.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This will later be used to include list initialization.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
No declaration of "hw/vfio/vfio-common.h" directly requires to include
the "exec/address-spaces.h" header. To simplify dependencies and
ease the upcoming cleanup of "exec/address-spaces.h", directly include
it in the source file where the declaration are used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-2-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to address_space_translate()
and address_space_translate_cached(). Callers either have an
attrs value to hand, or don't care and can use MEMTXATTRS_UNSPECIFIED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-4-peter.maydell@linaro.org
A recent patch fixed leaks of the dynamically allocated vcdev->vdev.name
field in vfio_ccw_realize(), but we now have three freeing sites for it.
This is unfortunate and seems to indicate something is wrong with its
life cycle.
The root issue is that vcdev->vdev.name is set before vfio_get_device()
is called, which theoretically prevents to call vfio_put_device() to
do the freeing. Well actually, we could call it anyway because
vfio_put_base_device() is a nop if the device isn't attached, but this
would be confusing.
This patch hence moves all the logic of attaching the device, including
the "already attached" check, to a separate vfio_ccw_get_device() function,
counterpart of vfio_put_device(). While here, vfio_put_device() is renamed
to vfio_ccw_put_device() for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <152326891065.266543.9487977590811413472.stgit@bahia.lan>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
During guest OS reboot, guest framebuffer is invalid. It will cause
bugs, if the invalid guest framebuffer is still used by host.
This patch is to introduce vfio_display_reset which is invoked
during vfio display reset. This vfio_display_reset function is used
to release the invalid display resource, disable scanout mode and
replace the invalid surface with QemuConsole's DisplaySurafce.
This patch can fix the GPU hang issue caused by gd_egl_draw during
guest OS reboot.
Changes v3->v4:
- Move dma-buf based display check into the vfio_display_reset().
(Gerd)
Changes v2->v3:
- Limit vfio_display_reset to dma-buf based vfio display. (Gerd)
Changes v1->v2:
- Use dpy_gfx_update_full() update screen after reset. (Gerd)
- Remove dpy_gfx_switch_surface(). (Gerd)
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Message-id: 1524820266-27079-3-git-send-email-tina.zhang@intel.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the subchannel is already attached or if vfio_get_device() fails, the
code jumps to the 'out_device_err' label and doesn't free the string it
has just allocated.
The code should be reworked so that vcdev->vdev.name only gets set when
the device has been attached, and freed when it is about to be detached.
This could be achieved with the addition of a vfio_ccw_get_device()
function that would be the counterpart of vfio_put_device(). But this is
a more elaborate cleanup that should be done in a follow-up. For now,
let's just add calls to g_free() on the buggy error paths.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <152311222681.203086.8874800175539040298.stgit@bahia>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 567b5b309a ("vfio/pci: Relax DMA map errors for MMIO regions")
added an error message if a passed memory section address or size
is not aligned to the page size and thus cannot be DMA mapped.
This patch fixes the trace by printing the region name and the
memory region section offset within the address space (instead of
offset_within_region).
We also turn the error_report into a trace event. Indeed, In some
cases, the traces can be confusing to non expert end-users and
let think the use case does not work (whereas it works as before).
This is the case where a BAR is successively mapped at different
GPAs and its sections are not compatible with dma map. The listener
is called several times and traces are issued for each intermediate
mapping. The end-user cannot easily match those GPAs against the
final GPA output by lscpi. So let's keep those information to
informed users. In mid term, the plan is to advise the user about
BAR relocation relevance.
Fixes: 567b5b309a ("vfio/pci: Relax DMA map errors for MMIO regions")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This adds a possibility for the platform to tell VFIO not to emulate MSIX
so MMIO memory regions do not get split into chunks in flatview and
the entire page can be registered as a KVM memory slot and make direct
MMIO access possible for the guest.
This enables the entire MSIX BAR mapping to the guest for the pseries
platform in order to achieve the maximum MMIO preformance for certain
devices.
Tested on:
LSI Logic / Symbios Logic SAS3008 PCI-Express Fusion-MPT SAS-3 (rev 02)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment we unconditionally avoid mapping MSIX data of a BAR and
emulate MSIX table in QEMU. However it is 1) not always necessary as
a platform may provide a paravirt interface for MSIX configuration;
2) can affect the speed of MMIO access by emulating them in QEMU when
frequently accessed registers share same system page with MSIX data,
this is particularly a problem for systems with the page size bigger
than 4KB.
A new capability - VFIO_REGION_INFO_CAP_MSIX_MAPPABLE - has been added
to the kernel [1] which tells the userspace that mapping of the MSIX data
is possible now. This makes use of it so from now on QEMU tries mapping
the entire BAR as a whole and emulate MSIX on top of that.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a32295c612c57990d17fb0f41e7134394b2f35f6
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment if vfio_memory_listener is registered in the system memory
address space, it maps/unmaps every RAM memory region for DMA.
It expects system page size aligned memory sections so vfio_dma_map
would not fail and so far this has been the case. A mapping failure
would be fatal. A side effect of such behavior is that some MMIO pages
would not be mapped silently.
However we are going to change MSIX BAR handling so we will end having
non-aligned sections in vfio_memory_listener (more details is in
the next patch) and vfio_dma_map will exit QEMU.
In order to avoid fatal failures on what previously was not a failure and
was just silently ignored, this checks the section alignment to
the smallest supported IOMMU page size and prints an error if not aligned;
it also prints an error if vfio_dma_map failed despite the page size check.
Both errors are not fatal; only MMIO RAM regions are checked
(aka "RAM device" regions).
If the amount of errors printed is overwhelming, the MSIX relocation
could be used to avoid excessive error output.
This is unlikely to cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: Fix Int128 bit ops]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Infrastructure for display support. Must be enabled
using 'display' property.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed By: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The license text currently specifies "any version" of the GPL. It
is unlikely that GPL v1 was ever intended; change this to the
standard "or any later version" text.
Cc: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
