The ability to zero regions of an image file is a useful primitive for
higher-level features such as image streaming or zero write detection.
Image formats may support an optimized metadata representation instead
of writing zeroes into the image file. This allows zero writes to be
potentially faster than regular write operations and also preserve
sparseness of the image file.
The .bdrv_co_write_zeroes() interface should be implemented by block
drivers that wish to provide efficient zeroing.
Note that this operation is different from the discard operation, which
may leave the contents of the region indeterminate. That means
discarded blocks are not guaranteed to contain zeroes and may contain
junk data instead.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add bdrv_find_backing_image: given a BlockDriverState pointer, and an id,
traverse the backing image chain to locate the id.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Previously copy-on-read could only be enabled for all requests to a
block device. This means requests coming from the guest as well as
QEMU's internal requests would perform copy-on-read when enabled.
For image streaming we want to support finer-grained behavior than just
populating the image file from its backing image. Image streaming
supports partial streaming where a common backing image is preserved.
In this case guest requests should not perform copy-on-read because they
would indiscriminately copy data which should be left in a backing image
from the backing chain.
Introduce a per-request flag for copy-on-read so that a block device can
process both regular and copy-on-read requests. Overlapping reads and
writes still need to be serialized for correctness when copy-on-read is
happening, so add an in-flight reference count to track this.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Long-running block operations like block migration and image streaming
must have continual access to their block device. It is not safe to
perform operations like hotplug, eject, change, resize, commit, or
external snapshot while a long-running operation is in progress.
This patch adds the missing bdrv_in_use() checks so that block migration
and image streaming never have the rug pulled out from underneath them.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Coverity is confused by this "if" and reports leaks on acb->bh.
The bottom half is always deleted before releasing the AIOCB,
in either bdrv_aio_cancel_em or bdrv_aio_bh_cb.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that early failure of bdrv_aio_writev is not possible anymore,
mcb->num_requests can be set before the loop starts.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Initially done with the following semantic patch:
@ rule1 @
expression E;
statement S;
@@
E =
(
bdrv_aio_readv
| bdrv_aio_writev
| bdrv_aio_flush
| bdrv_aio_discard
| bdrv_aio_ioctl
)
(...);
(
- if (E == NULL) { ... }
|
- if (E)
{ <... S ...> }
)
which however missed the occurrence in block/blkverify.c
(as it should have done), and left behind some unused
variables.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Many places in QEMU call qemu_aio_flush() to complete all pending
asynchronous I/O. Most of these places actually want to drain all block
requests but there is no block layer API to do so.
This patch introduces the bdrv_drain_all() API to wait for requests
across all BlockDriverStates to complete. As a bonus we perform checks
after qemu_aio_wait() to ensure that requests really have finished.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Debugging a reentrant request deadlock was fun but in the future we need
a quick and obvious way of detecting such bugs. Add an assert that
checks we are not about to deadlock when waiting for another request.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Cases beyond the end of the disk image are only implemented for block
drivers that do not provide .bdrv_co_is_allocated(). It's worth making
these cases generic so that block drivers that do implement
.bdrv_co_is_allocated() also get them for free.
Suggested-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Detect overlapping requests and remember to align to cluster boundaries
if the image format uses them. This assumes that allocating I/O is
performed in cluster granularity - which is true for qcow2, qed, etc.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When copy-on-read is enabled it is necessary to wait for overlapping
requests before issuing new requests. This prevents races between the
copy-on-read and a write request.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_enable_copy_on_read()/bdrv_disable_copy_on_read() functions can
be used to programmatically enable or disable copy-on-read for a block
device. Later patches add the actual copy-on-read logic.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The block layer does not know about pending requests. This information
is necessary for copy-on-read since overlapping requests must be
serialized to prevent races that corrupt the image.
The BlockDriverState gets a new tracked_request list field which
contains all pending requests. Each request is a BdrvTrackedRequest
record with sector_num, nb_sectors, and is_write fields.
Note that request tracking is always enabled but hopefully this extra
work is so small that it doesn't justify adding an enable/disable flag.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch introduces the public bdrv_co_is_allocated() interface which
can be used to query image allocation status while the VM is running.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all block drivers have been converted to
.bdrv_co_is_allocated() we can drop .bdrv_is_allocated().
Note that the public bdrv_is_allocated() interface is still available
but is in fact a synchronous wrapper around .bdrv_co_is_allocated().
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the .bdrv_co_is_allocated() interface which is identical
to .bdrv_is_allocated() but runs in coroutine context. Running in
coroutine context implies that other coroutines might be performing I/O
at the same time. Therefore it must be safe to run while the following
BlockDriver functions are in-flight:
.bdrv_co_readv()
.bdrv_co_writev()
.bdrv_co_flush()
.bdrv_co_is_allocated()
The new .bdrv_co_is_allocated() interface is useful because it can be
used when a VM is running, whereas .bdrv_is_allocated() is a synchronous
interface that does not cope with parallel requests.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no need for bdrv_commit() to use the BlockDriver
.bdrv_is_allocated() interface directly. Converting to the public
interface gives us the freedom to drop .bdrv_is_allocated() entirely in
favor of a new .bdrv_co_is_allocated() in the future.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Image files have two types of data: immutable data that describes things like
image size, backing files, etc. and mutable data that includes offset and
reference count tables.
Today, image formats aggressively cache mutable data to improve performance. In
some cases, this happens before a guest even starts. When dealing with live
migration, since a file is open on two machines, the caching of meta data can
lead to data corruption.
This patch addresses this by introducing a mechanism to invalidate any cached
mutable data a block driver may have which is then used by the live migration
code.
NB, this still requires coherent shared storage. Addressing migration without
coherent shared storage (i.e. NFS) requires additional work.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
cache=unsafe completely ignored bdrv_flush, because flushing the host disk
costs a lot of performance. However, this means that qcow2 images (and
potentially any other format) can lose data even after the guest has issued a
flush if the qemu process crashes/is killed. In case of a host crash, data loss
is certainly expected with cache=unsafe, but if just the qemu process dies this
is a bit too unsafe.
Now that we have two separate flush functions, we can choose to flush
everythign to the OS, but don't enforce that it's physically written to the
disk.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2 has a writeback metadata cache, so flushing a qcow2 image actually
consists of writing back that cache to the protocol and only then flushes the
protocol in order to get everything stable on disk.
This introduces a separate bdrv_co_flush_to_os to reflect the split.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are two different types of flush that you can do: Flushing one level up
to the OS (i.e. writing data to the host page cache) or flushing it all the way
down to the disk. The existing functions flush to the disk, reflect this in the
function name.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Recent versions of udev always keep the tray locked so that the kernel
can observe "eject request" events (aka tray button presses) even on
discs that aren't mounted. Add support for these events in the ATAPI
and SCSI cd drive device models.
To let management cope with the behavior of udev, an event should also
be added for "tray opened/closed". This way, after issuing an "eject"
command, management can poll until the guests actually reacts to the
command. They can then issue the "change" command after the tray has been
opened, or try with "eject -f" after a (configurable?) timeout. However,
with this patch and the corresponding support in the device models,
at least it is possible to do a manual two-step eject+change sequence.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several BlockDriverState fields are not being reinitialized across
bdrv_close()/bdrv_open(). Make sure they are reset to their default
values.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several block drivers set bs->read_only in .bdrv_open() but
block.c:bdrv_open_common() clobbers its value. Additionally, QED uses
bdrv_is_read_only() in .bdrv_open() to decide whether to perform
consistency checks.
The correct ordering is to initialize bs->read_only from the open flags
before calling .bdrv_open(). This way block drivers can override it if
necessary and can use bdrv_is_read_only() in .bdrv_open().
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
tmp_filename was used outside the block it was defined in, i.e. after it went
out of scope. Move its declaration to the top level.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Previous commits dropped most qobjects usage from qemu modules
(now they are a low level interface used by the QAPI). However,
some modules still include the qemu-objects.h header file.
This commit drops qemu-objects.h from some of those modules
and includes qjson.h instead, which is what they actually need.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The biggest change is to rename its prefix from BDRV_IOS to
BLOCK_DEVICE_IO_STATUS.
Next commit will convert the query-block command to the QAPI
and that's how the enumeration is going to be generated.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
A future commit will convert bdrv_info() to the QAPI and it won't
provide IOS_INVAL.
Luckily all we have to do is to add a new 'iostatus_enabled'
member to BlockDriverState and use it instead.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Since coroutine operation is now mandatory, convert both bdrv_discard
implementations to coroutines. For qcow2, this means taking the lock
around the operation. raw-posix remains synchronous.
The bdrv_discard callback is then unused and can be eliminated.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since coroutine operation is now mandatory, convert all bdrv_flush
implementations to coroutines. For qcow2, this means taking the lock.
Other implementations are simpler and just forward bdrv_flush to the
underlying protocol, so they can avoid the lock.
The bdrv_flush callback is then unused and can be eliminated.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This similarly adds support for coroutine and asynchronous discard.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add coroutine support for flush and apply the same emulation that
we already do for read/write. bdrv_aio_flush is simplified to always
go through a coroutine.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit cd74d83345e0e3b708330ab8c4cd9111bb82cda6 ("block: switch
bdrv_read()/bdrv_write() to coroutines") removed the bdrv_has_async_rw()
callers. This patch removes bdrv_has_async_rw() since it is no longer
used.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no need to emulate .bdrv_read()/.bdrv_write() since these
interfaces are only called if aio and coroutine interfaces are not
present. All valid BlockDrivers must implement either sync, aio, or
coroutine interfaces.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block drivers that implement coroutine functions used to get sync and
aio wrappers. This is no longer necessary since all request processing
now happens in a coroutine. If a block driver implements the coroutine
interface then none of the other interfaces will be invoked.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
More sync, aio, and coroutine unification. Make bdrv_aio_writev() go
through coroutine request processing.
Remove the dirty block callback mechanism which was needed only for aio
processing and can be done more naturally in coroutine context.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The aio write operation marks blocks dirty when the write operation
completes. The coroutine write operation marks blocks dirty before
issuing the write operation.
It seems safest to mark the block dirty when the operation completes so
that anything tracking dirty blocks will not act before the change has
been made to the image file.
Make the coroutine write operation dirty blocks on write completion.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
More sync, aio, and coroutine unification. Make bdrv_aio_readv() go
through coroutine request processing.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_read()/bdrv_write() functions call .bdrv_read()/.bdrv_write().
They should go through bdrv_co_do_readv() and bdrv_co_do_writev()
instead in order to unify request processing code across sync, aio, and
coroutine interfaces. This is also an important step towards removing
BlockDriverState .bdrv_read()/.bdrv_write() in the future.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The public interface for I/O in coroutine context is bdrv_co_readv() and
bdrv_co_writev(). Split out the request processing code into
bdrv_co_do_readv() and bdrv_co_writev() so that it can be called
internally when we refactor all request processing to use coroutines.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The emulation functions which supply default BlockDriver .bdrv_*()
functions given another implemented .bdrv_*() function should not use
public bdrv_*() interfaces. This patch ensures they invoke .bdrv_*()
directly to avoid adding an extra layer of coroutine request processing
and possibly entering an infinite loop.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We will unify block layer request processing across sync, aio, and
coroutines and this means a .bdrv_co_*() emulation function should not
call back into the public interface. There's no need here, just call
.bdrv_aio_*() directly.
The gory details: bdrv_co_io_em() cannot call back into the public
bdrv_aio_*() interface since that will be handled using coroutines,
which causes us to call into bdrv_co_io_em() again in an infinite loop
:).
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Contains the I/O status for the given device. The key is only present
if the device supports it and the VM is configured to stop on errors.
Please, check the documentation being added in this commit for more
information.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This commit adds support to the BlockDriverState type to keep track
of devices' I/O status.
There are three possible status: BDRV_IOS_OK (no error), BDRV_IOS_ENOSPC
(no space error) and BDRV_IOS_FAILED (any other error). The distinction
between no space and other errors is important because a management
application may want to watch for no space in order to extend the
space assigned to the VM and put it to run again.
Qemu devices supporting the I/O status feature have to enable it
explicitly by calling bdrv_iostatus_enable() _and_ have to be
configured to stop the VM on errors (ie. werror=stop|enospc or
rerror=stop).
In case of multiple errors being triggered in sequence only the first
one is stored. The I/O status is always reset to BDRV_IOS_OK when the
'cont' command is issued.
Next commits will add support to some devices and extend the
query-block/info block commands to return the I/O status information.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is useful to know the BlockDriverState as well as the
sector_num/nb_sectors of an emulated .bdrv_co_*() request.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
bdrv_open_common() is a useful point to trace since it reveals the
filename and block driver for a given BlockDriverState.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
To let device models distinguish between eject and load.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member buffer_alignment is initially 512. The device
model may set them, with bdrv_set_buffer_alignment(). If the device
model gets detached (hot unplug), the device's alignment is left
behind. Only okay because device hot unplug automatically destroys
the BlockDriverState. But that's a questionable feature, best not to
rely on it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models should be able to set it without an unclean include of
block_int.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Need to ask the device, so this requires new BlockDevOps member
is_tray_open().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's a confused mess (see previous commit). No users remain.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable is a confused mess. It is true when
an ide-cd, scsi-cd or floppy qdev is attached, or when the
BlockDriverState was created with -drive if={floppy,sd} or -drive
if={ide,scsi,xen,none},media=cdrom ("created removable"), except when
an ide-hd, scsi-hd, scsi-generic or virtio-blk qdev is attached.
Three users remain:
1. eject_device(), via bdrv_is_removable() uses it to determine
whether a block device can eject media.
2. bdrv_info() is monitor command "info block". QMP documentation
says "true if the device is removable, false otherwise". From the
monitor user's point of view, the only sensible interpretation of
"is removable" is "can eject media with monitor commands eject and
change".
A block device can eject media unless a device is attached that
doesn't support it. Switch the two users over to new
bdrv_dev_has_removable_media() that returns exactly that.
3. bdrv_getlength() uses to suppress its length cache when media can
change (see commit 46a4e4e6). Media change is either monitor
command change (updates the length cache), monitor command eject
(doesn't update the length cache, easily fixable), or physical
media change (invalidates length cache, not so easily fixable).
I'm refraining from improving anything here, because this series is
long enough already. Instead, I simply switch it over to
bdrv_dev_has_removable_media() as well.
This changes the behavior of the length cache and of monitor commands
eject and change in two cases:
a. drive not created removable, no device attached
The commit makes the drive removable, and defeats the length cache.
Example: -drive if=none
b. drive created removable, but the attached drive is non-removable,
and doesn't call bdrv_set_removable(..., 0) (most devices don't)
The commit makes the drive non-removable, and enables the length
cache.
Example: -drive if=xen,media=cdrom -M xenpv
The other non-removable devices that don't call
bdrv_set_removable() can't currently use a drive created removable,
either because they aren't qdevified, or because they lack a drive
property. Won't stay that way.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Requires new BlockDevOps member is_medium_locked(). Implement for IDE
and SCSI CD-ROMs.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The device model knows best when to accept the guest's eject command.
No need to detour through the block layer.
bdrv_eject() can't fail anymore. Make it void.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 4be9762a changed bdrv_is_inserted() to fail when the tray is
open. Unfortunately, there are two different kinds of users, with
conflicting needs.
1. Device models using bdrv_eject(), currently ide-cd and scsi-cd.
They expect bdrv_is_inserted() to reflect the tray status. Commit
4be9762a makes them happy.
2. Code that wants to know whether a BlockDriverState has media, such
as find_image_format(), bdrv_flush_all(). Commit 4be9762a makes them
unhappy. In particular, it breaks flush on VM stop for media ejected
by the guest.
Revert the change to bdrv_is_inserted(). Check the tray status in the
device models instead.
Note on IDE: Since only ATAPI devices have a tray, and they don't
accept ATA commands since the recent commit "ide: Reject ATA commands
specific to drive kinds", checking in atapi.c suffices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
savevm and loadvm silently ignore block devices with removable media,
such as floppies and SD cards. Rolling back a VM to a previous
checkpoint will *not* roll back writes to block devices with removable
media.
Moreover, bdrv_is_removable() is a confused mess, and wrong in at
least one case: it considers "-drive if=xen,media=cdrom -M xenpv"
removable. It'll be cleaned up later in this series.
Read-only block devices are also ignored, but that's okay.
Fix by ignoring only read-only block devices and empty block devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Change (!bdrv_is_removable(bs) || bdrv_is_inserted(bs)) to just
bdrv_is_inserted(). Rationale:
The value of bdrv_is_removable(bs) matters only when
bdrv_is_inserted(bs) is false.
bdrv_is_inserted(bs) is true when bs is open (bs->drv != NULL) and
not an empty host drive (CD-ROM or floppy).
Therefore, bdrv_is_removable(bs) matters only when:
1. bs is not open
old: may call bdrv_flush(bs), which does nothing
new: won't call
2. bs is an empty host drive
old: may call bdrv_flush(bs), which calls driver method
raw_flush(), which calls fdatasync() or equivalent, which
can't do anything useful while the drive is empty
new: won't call
Result is bs->drv && !bdrv_is_read_only(bs) && bdrv_is_inserted(bs).
bdrv_is_inserted(bs) implies bs->drv. Drop the redundant test.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Multiplexing callbacks complicates matters needlessly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For now, this just protects against programming errors like having the
same drive back multiple non-qdev devices, or untimely bdrv_delete().
Later commits will add other interesting uses.
While there, rename BlockDriverState member peer to dev, bdrv_attach()
to bdrv_attach_dev(), bdrv_detach() to bdrv_detach_dev(), and
bdrv_get_attached() to bdrv_get_attached_dev().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Most changes were made using these commands:
git grep -la '__attribute__((packed))'|xargs perl -pi -e 's/__attribute__\(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((packed))'|xargs perl -pi -e 's/__attribute__ \(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__((__packed__))'|xargs perl -pi -e 's/__attribute__\(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((__packed__))'|xargs perl -pi -e 's/__attribute__ \(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute((packed))'|xargs perl -pi -e 's/__attribute\(\(packed\)\)/QEMU_PACKED/'
Whitespace in linux-user/syscall_defs.h was fixed manually
to avoid warnings from scripts/checkpatch.pl.
Manual changes were also applied to hw/pc.c.
I did not fix indentation with tabs in block/vvfat.c.
The patch will show 4 errors with scripts/checkpatch.pl.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Account the total latency for read/write/flush requests. This allows
management tools to average it based on a snapshot of the nr ops
counters and allow checking for SLAs or provide statistics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Decouple the I/O accounting from bdrv_aio_readv/writev/flush and
make the hardware models call directly into the accounting helpers.
This means:
- we do not count internal requests from image formats in addition
to guest originating I/O
- we do not double count I/O ops if the device model handles it
chunk wise
- we only account I/O once it actuall is done
- can extent I/O accounting to synchronous or coroutine I/O easily
- implement I/O latency tracking easily (see the next patch)
I've conveted the existing device model callers to the new model,
device models that are using synchronous I/O and weren't accounted
before haven't been updated yet. Also scsi hasn't been converted
to the end-to-end accounting as I want to defer that after the pending
scsi layer overhaul.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds -drive cache=directsync for O_DIRECT | O_SYNC host file
I/O with no disk write cache presented to the guest.
This mode is useful when guests may not be sending flushes when
appropriate and therefore leave data at risk in case of power failure.
When cache=directsync is used, write operations are only completed to
the guest when data is safely on disk.
This new mode is like cache=writethrough but it bypasses the host page
cache.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch introduces bdrv_parse_cache_flags() which sets open flags
given a cache mode. Previously this was duplicated in blockdev.c and
qemu-img.c.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix code format to make checkpatch.pl happy.
Signed-off-by: Robert Wang <wdongxu@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If we're already in a coroutine, there is no reason to use the synchronous
version of block layer functions when a coroutine one exists. This makes
bdrv_read/write/flush use bdrv_co_* when used inside a coroutine.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The purpose of AsyncContexts was to protect qcow and qcow2 against reentrancy
during an emulated bdrv_read/write (which includes a qemu_aio_wait() call and
can run AIO callbacks of different requests if it weren't for AsyncContexts).
Now both qcow and qcow2 are protected by CoMutexes and AsyncContexts can be
removed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to be able to call bdrv_co_readv/writev for drivers that don't
implement the functions natively, add an emulation that uses the AIO functions
to implement them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use the bdrv_co_readv/writev callbacks to implement bdrv_aio_readv/writev and
bdrv_read/write if a driver provides the coroutine version instead of the
synchronous or AIO version.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add new block driver callbacks bdrv_co_readv/writev, which work on a
QEMUIOVector like bdrv_aio_*, but don't need a callback. The function may only
be called inside a coroutine, so a block driver implementing this interface can
yield instead of blocking during I/O.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit aea2a33c made bdrv_eject() obey the locked flag. Correct for
medium eject (eject_flag set), incorrect for medium load (eject_flag
clear). See MMC-5 Table 341 "Actions for Lock/Unlock/Eject".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Callees always return 0, except for FreeBSD's cdrom_eject(), which
returns -ENOTSUP when the device is in a terminally wedged state.
The only caller is bdrv_eject(), and it maps -ENOTSUP to 0 since
commit 4be9762a.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState members change_cb and change_opaque are initially
null. The device model may set them, with bdrv_set_change_cb(). If
the device model gets detached (hot unplug), they're left dangling.
Only safe because device hot unplug automatically destroys the
BlockDriverState. But that's a questionable feature, best not to rely
on it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu-img.c wants to count allocated file size of image. Previously it
counts a single bs->file by 'stat' or Window API. As VMDK introduces
multiple file support, the operation becomes format specific with
platform specific meanwhile.
The functions are moved to block/raw-{posix,win32}.c and qemu-img.c calls
bdrv_get_allocated_file_size to count the bs. And also added VMDK code
to count his own extents.
Signed-off-by: Fam Zheng <famcool@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block drivers that don't support creating images don't have a size option. Fail
gracefully instead of segfaulting when trying to access the option's value.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Change BDRV_O_NOCACHE to only imply bypassing the host OS file cache,
but no writeback semantics. All existing callers are changed to also
specify BDRV_O_CACHE_WB to give them writeback semantics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
No users of bdrv_get_type_hint() left. bdrv_set_type_hint() can make
the media removable by side effect. Make that explicit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
query-block's specification documents response member "type" with
values "hd", "cdrom", "floppy", "unknown".
Its value is unreliable: a block device used as floppy has type
"floppy" if created with if=floppy, but type "hd" if created with
if=none.
That's because with if=none, the type is at best a declaration of
intent: the drive can be connected to any guest device. Its type is
really the guest device's business. Reporting it here is wrong.
No known user of QMP uses "type". It's unlikely that any unknown
users exist, because its value is useless unless you know how the
block device was created. But then you also know the true value.
Fixing the broken value risks breaking (hypothetical!) clients that
somehow rely on the current behavior. Not fixing the value risks
breaking (hypothetical!) clients that rely on the value to be
accurate. Can't entirely avoid hypothetical lossage. Change the
value to be always "unknown".
This makes "info block" always report "type=unknown". Pointless.
Change it to not report the type.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The code changed here is an unused data type name (evt_flush_occurred).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The block layer caches the device size to avoid doing lseek(fd, 0,
SEEK_END) every time this value is needed. For removable media the
device size becomes stale if a new medium is inserted. This patch
simply prevents device size caching for removable media.
A smarter solution is to update the cached device size when a new medium
is inserted. Given that there are currently bugs with CD-ROM media
change I do not want to implement that approach until we've gotten
things correct first.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It can be handy to know when the guest locks/unlocks the CD-ROM tray.
This trace event makes that possible.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When removing a drive from the host-side via drive_del we currently have
the following path:
drive_del
qemu_aio_flush()
bdrv_close() // zaps bs->drv, which makes any subsequent I/O get
// dropped. Works as designed
drive_uninit()
bdrv_delete() // frees the bs. Since the device is still connected to
// bs, any subsequent I/O is a use-after-free.
The value of bs->drv becomes unpredictable on free. As long as it
remains null, I/O still gets dropped, however it could become non-null
at any point after the free resulting SEGVs or other QEMU state
corruption.
To resolve this issue as simply as possible, we can chose to not
actually delete the BlockDriverState pointer. Since bdrv_close()
handles setting the drv pointer to NULL, we just need to remove the
BlockDriverState from the QLIST that is used to enumerate the block
devices. This is currently handled within bdrv_delete, so move this
into its own function, bdrv_make_anon().
The result is that we can now invoke drive_del, this closes the file
descriptors and sets BlockDriverState->drv to NULL which prevents futher
IO to the device, and since we do not free BlockDriverState, we don't
have to worry about the copy retained in the block devices.
We also don't attempt to remove the qdev property since we are no longer
deleting the BlockDriverState on drives with associated drives. This
also allows for removing Drives with no devices associated either.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If the block device has been closed, we no longer have a medium to submit
IO against, check for this before submitting io. This prevents a segfault
further in the code where we dereference elements of the block driver.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a trace event for bdrv_aio_flush() to complement the existing
bdrv_aio_readv() and bdrv_aio_writev() events.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Other geometry guessing functions already reside in block.c.
Remove some unused or debugging only fields.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Set block device in use during block migration, disallow drive_del and
bdrv_truncate for in use devices.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Certain operations such as drive_del or resize cannot be performed
while external users (eg. block migration) reference the block device.
Add a flag to indicate that.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extend the change_cb callback with a reason argument, and use it
to tell drivers about size changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The backing format should be honored during image creation. For some
reason we currently use the image format to open the backing file. This
fails when the backing file has a different format than the image being
created. Keep the image and backing format drivers completely separate.
Also print the backing filename if there is an error opening the backing
file instead of the image filename.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Avoid a warning with GCC 4.6.0:
/src/qemu/block.c: In function 'bdrv_img_create':
/src/qemu/block.c:2862:25: error: variable 'fmt' set but not used [-Werror=unused-but-set-variable]
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add a new bdrv_discard method to free blocks in a mapping image, and a new
drive property to set the granularity for these discard. If no discard
granularity support is set discard support is disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Kevin suggested to have bdrv_img_create() return proper -errno values
on error.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch re-factors img_create() moving the code doing the actual
work into block.c where it can be shared with QEMU. This is needed to
be able to create images from QEMU to be used for live snapshots.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Backing filenames may contain a protocol. The code currently doesn't
consider this case and produces filenames that embed "<protocol>:".
Don't combine filenames if the backing filename contains a protocol.
Based on an earlier patch by Anthony Liguori <aliguori@us.ibm.com>.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_find_protocol() function returns NULL if an unknown protocol
name is given. It returns the "file" protocol when the filename
contains no protocol at all. This makes it difficult to distinguish
between paths which contain a protocol and those which do not.
Factor out a helper function that tests whether or not a filename has a
protocol. The next patch makes use of this function.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Filenames may start with "<protocol>:" to explicitly use a protocol like
nbd. Filenames with unknown protocols are rejected in most of QEMU
except for bdrv_create_file(). Even if a file with an invalid filename
can be created, QEMU cannot use it since all the other relevant
functions reject such paths. Make bdrv_create_file() consistent.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sectors are marked dirty in the bitmap on AIO submission. This is wrong
since data has not reached storage.
Set a given sector as dirty in the dirty bitmap on AIO completion, so that
reading a sector marked as dirty is guaranteed to return uptodate data.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Otherwise upper 32 bits of bitmap entries are not correctly calculated.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This changes bdrv_flush to return 0 on success and -errno in case of failure.
It's a requirement for implementing proper error handle in users of bdrv_flush.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
In order to backup snapshots, created from QCOW2 iamge, we want to copy snapshots out of QCOW2 disk to a seperate storage.
The following patch adds a new option in "qemu-img": qemu-img convert -f qcow2 -O qcow2 -s snapshot_name src_img bck_img.
Right now, it only supports to copy the full snapshot, delta snapshot is on the way.
Changes from V1: all the comments from Kevin are addressed:
Add read-only checking
Fix coding style
Change the name from bdrv_snapshot_load to bdrv_snapshot_load_tmp
Signed-off-by: Disheng Su <edison@cloud.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Observing block layer aio readv/writev operations is useful for
debugging image formats or understanding guest disk I/O patterns.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit 79368c81bf.
Conflicts:
block.c
I haven't been able to come up with a solution yet for the corruption caused by
unaligned requests from the IDE disk so revert until a solution can be written.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Arguably we should re-open the backing file with the backing file format and
not with the format of the snapshot image.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_eject() gets called when a device model opens or closes the tray.
If the block driver implements method bdrv_eject(), that method gets
called. Drivers host_cdrom implements it, and it opens and closes the
physical tray, and nothing else. When a device model opens, then
closes the tray, media changes only if the user actively changes the
physical media while the tray is open. This is matches how physical
hardware behaves.
If the block driver doesn't implement method bdrv_eject(), we do
something quite different: opening the tray severs the connection to
the image by calling bdrv_close(), and closing the tray does nothing.
When the device model opens, then closes the tray, media is gone,
unless the user actively inserts another one while the tray is open,
with a suitable change command in the monitor. This isn't how
physical hardware behaves. Rather inconvenient when programs
"helpfully" eject media to give you a chance to change it. The way
bdrv_eject() behaves here turns that chance into a must, which is not
what these programs or their users expect.
Change the default action not to call bdrv_close(). Instead, note the
tray status in new BlockDriverState member tray_open. Use it in
bdrv_is_inserted().
Arguably, the device models should keep track of tray status
themselves. But this is less invasive.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Assuming that any image on a block device is not properly zero-initialized is
actually wrong: Only raw images have this problem. Any other image format
shouldn't care about it, they initialize everything properly themselves.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_commit copies the image to its backing file sector by sector, which
is (surprise!) relatively slow. Let's take a larger buffer and handle more
sectors at once if possible.
With a 1G qcow2 file, this brought the time bdrv_commit takes down from
5:06 min to 1:14 min for me.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block device change command did not copy BDRV_O_SNAPSHOT flag. Thus
the new image did not have this flag and the file got deleted during
opening.
Fix by copying BDRV_O_SNAPSHOT flag.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
"No such file or directory" is a misleading error message
when a user tries to open a file with wrong permissions.
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
CVE-2008-2004 described a vulnerability in QEMU whereas a malicious user could
trick the block probing code into accessing arbitrary files in a guest. To
mitigate this, we added an explicit format parameter to -drive which disabling
block probing.
Fast forward to today, and the vast majority of users do not use this parameter.
libvirt does not use this by default nor does virt-manager.
Most users want block probing so we should try to make it safer.
This patch adds some logic to the raw device which attempts to detect a write
operation to the beginning of a raw device. If the first 4 bytes happen to
match an image file that has a backing file that we support, it scrubs the
signature to all zeros. If a user specifies an explicit format parameter, this
behavior is disabled.
I contend that while a legitimate guest could write such a signature to the
header, we would behave incorrectly anyway upon the next invocation of QEMU.
This simply changes the incorrect behavior to not involve a security
vulnerability.
I've tested this pretty extensively both in the positive and negative case. I'm
not 100% confident in the block layer's ability to deal with zero sized writes
particularly with respect to the aio functions so some additional eyes would be
appreciated.
Even in the case of a single sector write, we have to make sure to invoked the
completion from a bottom half so just removing the zero sized write is not an
option.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This distinguishes between harmless leaks and real corruption. Hopefully users
better understand what qemu-img check wants to tell them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
People think that their images are corrupted when in fact there are just some
leaked clusters. Differentiating several error cases should make the messages
more comprehensible.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Don't try to be clever by freeing all temporary data and calling all callbacks
when the return value (an error) is certain. Doing so has at least two
important problems:
* The temporary data that is freed (qiov, possibly zero buffer) is still used
by the requests that have not yet completed.
* Calling the callbacks for all requests in the multiwrite means for the caller
that it may free buffers etc. which are still in use.
Just remember the error value and do the cleanup when all requests have
completed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_aio_writev may call the callback immediately (and it will commonly do so
in error cases). Current code doesn't consider this. For details see the
comment added by this patch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
savevm.c keeps a pointer to the snapshot block device. If you manage
to get that device deleted, the pointer dangles, and the next snapshot
operation will crash & burn. Unplugging a guest device that uses it
does the trick:
$ MALLOC_PERTURB_=234 qemu-system-x86_64 [...]
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) info snapshots
No available block device supports snapshots
(qemu) drive_add auto if=none,file=tmp.qcow2
OK
(qemu) device_add usb-storage,id=foo,drive=none1
(qemu) info snapshots
Snapshot devices: none1
Snapshot list (from none1):
ID TAG VM SIZE DATE VM CLOCK
(qemu) device_del foo
(qemu) info snapshots
Snapshot devices:
Segmentation fault (core dumped)
Move management of that pointer to block.c, and zap it when the device
it points becomes unusable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For instance, -device scsi-disk,drive=foo -device scsi-disk,drive=foo
happily creates two SCSI disks connected to the same block device.
It's all downhill from there.
Device usb-storage deliberately attaches twice to the same blockdev,
which fails with the fix in place. Detach before the second attach
there.
Also catch attempt to delete while a guest device model is attached.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To fix https://bugs.launchpad.net/qemu/+bug/597402 where qemu fails to
call unlink() on temporary snapshots due to bs->is_temporary getting clobbered
in bdrv_open_common() after being set in bdrv_open() which calls the former.
We don't need to initialize bs->is_temporary in bdrv_open_common().
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before the raw/file split we used to allow filenames with colons for host
device only. While this was more by accident than by design people rely
on it, so we need to bring it back.
So move the host device probing to be before the protocol detection
again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add new functions that write and flush the written data to disk immediately.
This is what needs to be used for image format metadata to maintain integrity
for cache=... modes that don't use O_DSYNC. (Actually, we only need barriers,
and therefore the functions are defined as such, but flushes is what is
implemented in this patch - we can try to change that later)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix a warning from OpenBSD gcc (3.3.5 (propolice)):
/src/qemu/block.c: In function `bdrv_info_stats_bs':
/src/qemu/block.c:1548: warning: long long int format, long unsigned
int arg (arg 6)
There may be also truncation effects.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is a more flexible alternative to bdrv_iterate().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
do_commit() and mux_proc_byte() iterate over the list of drives
defined with drive_init(). This misses host block devices defined by
other means. Such means don't exist now, but will be introduced later
in this series.
Change them to use new bdrv_commit_all(), which iterates over all host
block devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Both bdrv_can_snapshot() and bdrv_has_snapshot() does not work as advertized.
First issue: Their names implies different porpouses, but they do the same thing
and have exactly the same code. Maybe copied and pasted and forgotten?
bdrv_has_snapshot() is called in various places for actually checking if there
is snapshots or not.
Second issue: the way bdrv_can_snapshot() verifies if a block driver supports or
not snapshots does not catch all cases. E.g.: a raw image.
So when do_savevm() is called, first thing it does is to set a global
BlockDriverState to save the VM memory state calling get_bs_snapshots().
static BlockDriverState *get_bs_snapshots(void)
{
BlockDriverState *bs;
DriveInfo *dinfo;
if (bs_snapshots)
return bs_snapshots;
QTAILQ_FOREACH(dinfo, &drives, next) {
bs = dinfo->bdrv;
if (bdrv_can_snapshot(bs))
goto ok;
}
return NULL;
ok:
bs_snapshots = bs;
return bs;
}
bdrv_can_snapshot() may return a BlockDriverState that does not support
snapshots and do_savevm() goes on.
Later on in do_savevm(), we find:
QTAILQ_FOREACH(dinfo, &drives, next) {
bs1 = dinfo->bdrv;
if (bdrv_has_snapshot(bs1)) {
/* Write VM state size only to the image that contains the state */
sn->vm_state_size = (bs == bs1 ? vm_state_size : 0);
ret = bdrv_snapshot_create(bs1, sn);
if (ret < 0) {
monitor_printf(mon, "Error while creating snapshot on '%s'\n",
bdrv_get_device_name(bs1));
}
}
}
bdrv_has_snapshot(bs1) is not checking if the device does support or has
snapshots as explained above. Only in bdrv_snapshot_create() the device is
actually checked for snapshot support.
So, in cases where the first device supports snapshots, and the second does not,
the snapshot on the first will happen anyways. I believe this is not a good
behavior. It should be an all or nothing process.
This patch addresses these issues by making bdrv_can_snapshot() actually do
what it must do and enforces better tests to avoid errors in the middle of
do_savevm(). bdrv_has_snapshot() is removed and replaced by bdrv_can_snapshot()
where appropriate.
bdrv_can_snapshot() was moved from savevm.c to block.c. It makes more sense to me.
The loadvm_state() function was updated too to enforce that when loading a VM at
least all writable devices must support snapshots too.
Signed-off-by: Miguel Di Ciurcio Filho <miguel.filho@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When snapshot handlers are not defined in the format driver, it is
better to call the ones of the protocol driver. This enables us to
implement snapshot support in the protocol driver.
We need to call bdrv_close() and bdrv_open() handlers of the format
driver before and after bdrv_snapshot_goto() call of the protocol. It is
because the contents of the block driver state may need to be changed
after loading vmstate.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch calls the close handler of the block driver before the qemu
process exits.
This is necessary because the sheepdog block driver releases the lock
of VM images in the close handler.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu -cdrom /dev/cdrom with an empty CD-ROM drive doesn't work any more because
we try to guess the format and when this fails (because there is no medium) we
exit with an error message.
This patch should restore the old behaviour by assuming raw format for such
drives.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
