The NVIC is a core v7M device that exists for all v7M CPUs;
put it under a CONFIG_ARM_V7M rather than hiding it under
CONFIG_STELLARIS.
(We'll use CONFIG_ARM_V7M for the SysTick device too
when we split it out of the NVIC.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-9-git-send-email-peter.maydell@linaro.org
Instead of the bitband device doing a cpu_physical_memory_read/write,
make it take a MemoryRegion which specifies where it should be
accessing, and use address_space_read/write to access the
corresponding AddressSpace.
Since this entails pretty much a rewrite, convert away from
old_mmio in the process.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-8-git-send-email-peter.maydell@linaro.org
Make the NVIC device expose a memory region for its users
to map, rather than mapping itself into the system memory
space on realize, and get the one user (the ARMv7M object)
to do this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-7-git-send-email-peter.maydell@linaro.org
Make the ARMv7M object take a memory region link which it uses
to wire up the bitband rather than having them always put
themselves in the system address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-6-git-send-email-peter.maydell@linaro.org
Make the legacy armv7m_init() function use the newly QOMified
armv7m object rather than doing everything by hand.
We can return the armv7m object rather than the NVIC from
armv7m_init() because its interface to the rest of the
board (GPIOs, etc) is identical.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-5-git-send-email-peter.maydell@linaro.org
Create a proper QOM object for the armv7m container, which
holds the CPU, the NVIC and the bitband regions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-4-git-send-email-peter.maydell@linaro.org
Move the NVICState struct definition into a header, so we can
embed it into other QOM objects like SoCs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-3-git-send-email-peter.maydell@linaro.org
Abstract the "load kernel" code out of armv7m_init() into its own
function. This includes the registration of the CPU reset function,
to parallel how we handle this for A profile cores.
We make the function public so that boards which choose to
directly instantiate an ARMv7M device object can call it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-2-git-send-email-peter.maydell@linaro.org
The Exynos4210 has cluster ID 0x9 in its MPIDR register (raw value
0x8000090x). If this cluster ID is not provided, then Linux kernel
cannot map DeviceTree nodes to MPIDR values resulting in kernel
warning and lack of any secondary CPUs:
DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
...
smp: Bringing up secondary CPUs ...
smp: Brought up 1 node, 1 CPU
SMP: Total of 1 processors activated (24.00 BogoMIPS).
Provide a cluster ID so Linux will see proper MPIDR and will try to
bring the secondary CPU online.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-id: 20170226200142.31169-2-krzk@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Without any clock controller, the Linux kernel was hitting division by
zero during boot or with clk_summary:
[ 0.000000] [<c031054c>] (unwind_backtrace) from [<c030ba6c>] (show_stack+0x10/0x14)
[ 0.000000] [<c030ba6c>] (show_stack) from [<c05b2660>] (dump_stack+0x88/0x9c)
[ 0.000000] [<c05b2660>] (dump_stack) from [<c05b11a4>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c05b11a4>] (Ldiv0) from [<c06ad1e0>] (samsung_pll45xx_recalc_rate+0x58/0x74)
[ 0.000000] [<c06ad1e0>] (samsung_pll45xx_recalc_rate) from [<c0692ec0>] (clk_register+0x39c/0x63c)
[ 0.000000] [<c0692ec0>] (clk_register) from [<c125d360>] (samsung_clk_register_pll+0x2e0/0x3d4)
[ 0.000000] [<c125d360>] (samsung_clk_register_pll) from [<c125d7e8>] (exynos4_clk_init+0x1b0/0x5e4)
[ 0.000000] [<c125d7e8>] (exynos4_clk_init) from [<c12335f4>] (of_clk_init+0x17c/0x210)
[ 0.000000] [<c12335f4>] (of_clk_init) from [<c1204700>] (time_init+0x24/0x2c)
[ 0.000000] [<c1204700>] (time_init) from [<c1200b2c>] (start_kernel+0x24c/0x38c)
[ 0.000000] [<c1200b2c>] (start_kernel) from [<4020807c>] (0x4020807c)
Provide stub for clock controller returning reset values for PLLs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-id: 20170226200142.31169-1-krzk@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the BCM2835 SDHost controller from Arasan.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Message-id: 20170224164021.9066-2-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the NVIC SHCSR write behaviour which allows pending and
active status of some exceptions to be changed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Implement the exception return consistency checks
described in the v7M pseudocode ExceptionReturn().
Inspired by a patch from Michael Davidsaver's series, but
this is a reimplementation from scratch based on the
ARM ARM pseudocode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The VECTCLRACTIVE and VECTRESET bits in the AIRCR are both
documented as UNPREDICTABLE if you write a 1 to them when
the processor is not halted in Debug state (ie stopped
and under the control of an external JTAG debugger).
Since we don't implement Debug state or emulated JTAG
these bits are always UNPREDICTABLE for us. Instead of
logging them as unimplemented we can simply log writes
as guest errors and ignore them.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: change extracted from another patch; commit message
constructed from scratch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Having armv7m_nvic_acknowledge_irq() return the new value of
env->v7m.exception and its one caller assign the return value
back to env->v7m.exception is pointless. Just make the return
type void instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The v7M exception architecture requires that if a synchronous
exception cannot be taken immediately (because it is disabled
or at too low a priority) then it should be escalated to
HardFault (and the HardFault exception is then taken).
Implement this escalation logic.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: extracted from another patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Now that the NVIC is its own separate implementation, we can
clean up the GIC code by removing REV_NVIC and conditionals
which use it.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The M profile condition for when we can take a pending exception or
interrupt is not the same as that for A/R profile. The code
originally copied from the A/R profile version of the
cpu_exec_interrupt function only worked by chance for the
very simple case of exceptions being masked by PRIMASK.
Replace it with a call to a function in the NVIC code that
correctly compares the priority of the pending exception
against the current execution priority of the CPU.
[Michael Davidsaver's patchset had a patch to do something
similar but the implementation ended up being a rewrite.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Despite some superficial similarities of register layout, the
M-profile NVIC is really very different from the A-profile GIC.
Our current attempt to reuse the GIC code means that we have
significant bugs in our NVIC.
Implement the NVIC as an entirely separate device, to give
us somewhere we can get the behaviour correct.
This initial commit does not attempt to implement exception
priority escalation, since the GIC-based code didn't either.
It does fix a few bugs in passing:
* ICSR.RETTOBASE polarity was wrong and didn't account for
internal exceptions
* ICSR.VECTPENDING was 16 too high if the pending exception
was for an external interrupt
* UsageFault, BusFault and MemFault were not disabled on reset
as they are supposed to be
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: reworked, various bugs and stylistic cleanups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Add a state field for the v7M PRIGROUP register and implent
reading and writing it. The current NVIC doesn't honour
the values written, but the new version will.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Rename the nvic_state struct to NVICState, to match
our naming conventions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The i.MX timer device can be reset by writing to the SWR bit
of the CR register. This has to behave differently from hard
(power-on) reset because it does not reset all of the bits
in the CR register.
We were incorrectly implementing soft reset and hard reset
the same way, and in addition had a logic error which meant
that we were clearing the bits that soft-reset is supposed
to preserve and not touching the bits that soft-reset clears.
This was not correct behaviour for either kind of reset.
Separate out the soft reset and hard reset code paths, and
correct the handling of reset of the CR register so that it
is correct in both cases.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
[PMM: rephrased commit message, spacing on operators;
use bool rather than int for is_soft_reset]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In 2.9 ITS will block save/restore and migration use cases. As such,
let's introduce a user option that allows to turn its instantiation
off, along with GICv3. With the "its" option turned false, migration
will be possible, obviously at the expense of MSI support (with GICv3).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487681108-14452-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
object_new(FOO) returns an object with ref_cnt == 1
and following
object_property_set_bool(cpuobj, true, "realized", NULL)
set parent of cpuobj to '/machine/unattached' which makes
ref_cnt == 2.
Since machvirt_init() doesn't take ownership of cpuobj
returned by object_new() it should explicitly drop
reference to cpuobj when dangling pointer is about to
go out of scope like it's done pc_new_cpu() to avoid
object leak.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 1487253461-269218-1-git-send-email-imammedo@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SDHCI protocol, the 'Block count enable' bit of the Transfer
Mode register is relevant only in multi block transfers. We need
not check it in single block transfers.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-5-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In sdhci_write invoke multi block transfer if it is enabled
in the transfer mode register 's->trnmod'.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-4-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the SDHCI protocol, the transfer mode register value
is used during multi block transfer to check if block count
register is enabled and should be updated. Transfer mode
register could be set such that, block count register would
not be updated, thus leading to an infinite loop. Add check
to avoid it.
Reported-by: Wjjzhang <wjjzhang@tencent.com>
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-3-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SDHCI protocol, the transfer mode register is defined
to be of 6 bits. Mask its value with '0x0037' so that an
invalid value could not be assigned.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170214185225.7994-2-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch to using qcrypto_random_bytes() rather than rand() as
our source of randomness for the BCM2835 RNG.
If qcrypto_random_bytes() fails, we don't want to return the guest a
non-random value in case they're really using it for cryptographic
purposes, so the best we can do is a fatal error. This shouldn't
happen unless something's broken, though.
In theory we could implement this device's full FIFO and interrupt
semantics and then just stop filling the FIFO. That's a lot of work,
though, and doesn't really give a very nice diagnostic to the user
since the guest will just seem to hang.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Recent vanilla Raspberry Pi kernels started to make use of
the hardware random number generator in BCM2835 SoC. As a
result, those kernels wouldn't work anymore under QEMU
but rather just freeze during the boot process.
This patch implements a trivial BCM2835 compatible RNG,
and adds it as a peripheral to BCM2835 platform, which
allows to boot a vanilla Raspberry Pi kernel under Qemu.
Changes since v1:
* Prevented guest from writing [31..20] bits in rng_status
* Removed redundant minimum_version_id_old
* Added field entries for the state
* Changed realize function to reset
Signed-off-by: Marcin Chojnacki <marcinch7@gmail.com>
Message-id: 20170210210857.47893-1-marcinch7@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit a3a3d8c7 introduced a segfault bug while checking for
'dc->vmsd->unmigratable' which caused QEMU to crash when trying to add
devices which do no set their 'dc->vmsd' yet while initialization.
Place a 'dc->vmsd' check prior to it so that we do not segfault for
such devices.
NOTE: This doesn't compromise the functioning of --only-migratable
option as all the unmigratable devices do set their 'dc->vmsd'.
Introduce a new function check_migratable() and move the
only_migratable check inside it, also use stubs to avoid user-mode qemu
build failures.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1487009088-23891-1-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Load the network boot image into guest RAM when the boot
device selected is a network device. Use some of the reserved
space in IplBlockCcw to store the start address of the netboot
image.
A user could also use 'chreipl'(diag 308/5) to change the boot device.
So every time we update the IPLB, we need to verify if the selected
boot device is a network device so we can appropriately load the
network boot image.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Add new field to S390IPLState to store the name of the network boot
loader.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The current QEMU ROM infrastructure rejects late loading of ROMs.
And ELFs are currently loaded as ROM, this prevents delayed loading
of ELFs. So when loading ELF, allow the user to specify if ELF should
be loaded as ROM or not.
If an ELF is not loaded as ROM, then they are not restored on a
guest reboot/reset and so its upto the user to handle the reloading.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Now that the all callbacks have been converted to use "at" syscalls, we
can drop this code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_open2() callback is vulnerable to symlink attacks because it
calls:
(1) open() which follows symbolic links for all path elements but the
rightmost one
(2) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(3) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
(4) local_post_create_passthrough() which calls in turn lchown() and
chmod(), both functions also following symbolic links
This patch converts local_open2() to rely on opendir_nofollow() and
mkdirat() to fix (1), as well as local_set_xattrat(),
local_set_mapped_file_attrat() and local_set_cred_passthrough() to
fix (2), (3) and (4) respectively. Since local_open2() already opens
a descriptor to the target file, local_set_cred_passthrough() is
modified to reuse it instead of opening a new one.
The mapped and mapped-file security modes are supposed to be identical,
except for the place where credentials and file modes are stored. While
here, we also make that explicit by sharing the call to openat().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_mkdir() callback is vulnerable to symlink attacks because it
calls:
(1) mkdir() which follows symbolic links for all path elements but the
rightmost one
(2) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(3) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
(4) local_post_create_passthrough() which calls in turn lchown() and
chmod(), both functions also following symbolic links
This patch converts local_mkdir() to rely on opendir_nofollow() and
mkdirat() to fix (1), as well as local_set_xattrat(),
local_set_mapped_file_attrat() and local_set_cred_passthrough() to
fix (2), (3) and (4) respectively.
The mapped and mapped-file security modes are supposed to be identical,
except for the place where credentials and file modes are stored. While
here, we also make that explicit by sharing the call to mkdirat().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_mknod() callback is vulnerable to symlink attacks because it
calls:
(1) mknod() which follows symbolic links for all path elements but the
rightmost one
(2) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(3) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
(4) local_post_create_passthrough() which calls in turn lchown() and
chmod(), both functions also following symbolic links
This patch converts local_mknod() to rely on opendir_nofollow() and
mknodat() to fix (1), as well as local_set_xattrat() and
local_set_mapped_file_attrat() to fix (2) and (3) respectively.
A new local_set_cred_passthrough() helper based on fchownat() and
fchmodat_nofollow() is introduced as a replacement to
local_post_create_passthrough() to fix (4).
The mapped and mapped-file security modes are supposed to be identical,
except for the place where credentials and file modes are stored. While
here, we also make that explicit by sharing the call to mknodat().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_symlink() callback is vulnerable to symlink attacks because it
calls:
(1) symlink() which follows symbolic links for all path elements but the
rightmost one
(2) open(O_NOFOLLOW) which follows symbolic links for all path elements but
the rightmost one
(3) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(4) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
This patch converts local_symlink() to rely on opendir_nofollow() and
symlinkat() to fix (1), openat(O_NOFOLLOW) to fix (2), as well as
local_set_xattrat() and local_set_mapped_file_attrat() to fix (3) and
(4) respectively.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_chown() callback is vulnerable to symlink attacks because it
calls:
(1) lchown() which follows symbolic links for all path elements but the
rightmost one
(2) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(3) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
This patch converts local_chown() to rely on open_nofollow() and
fchownat() to fix (1), as well as local_set_xattrat() and
local_set_mapped_file_attrat() to fix (2) and (3) respectively.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_chmod() callback is vulnerable to symlink attacks because it
calls:
(1) chmod() which follows symbolic links for all path elements
(2) local_set_xattr()->setxattr() which follows symbolic links for all
path elements
(3) local_set_mapped_file_attr() which calls in turn local_fopen() and
mkdir(), both functions following symbolic links for all path
elements but the rightmost one
We would need fchmodat() to implement AT_SYMLINK_NOFOLLOW to fix (1). This
isn't the case on linux unfortunately: the kernel doesn't even have a flags
argument to the syscall :-\ It is impossible to fix it in userspace in
a race-free manner. This patch hence converts local_chmod() to rely on
open_nofollow() and fchmod(). This fixes the vulnerability but introduces
a limitation: the target file must readable and/or writable for the call
to openat() to succeed.
It introduces a local_set_xattrat() replacement to local_set_xattr()
based on fsetxattrat() to fix (2), and a local_set_mapped_file_attrat()
replacement to local_set_mapped_file_attr() based on local_fopenat()
and mkdirat() to fix (3). No effort is made to factor out code because
both local_set_xattr() and local_set_mapped_file_attr() will be dropped
when all users have been converted to use the "at" versions.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_link() callback is vulnerable to symlink attacks because it calls:
(1) link() which follows symbolic links for all path elements but the
rightmost one
(2) local_create_mapped_attr_dir()->mkdir() which follows symbolic links
for all path elements but the rightmost one
This patch converts local_link() to rely on opendir_nofollow() and linkat()
to fix (1), mkdirat() to fix (2).
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
When using the mapped-file security model, we also have to create a link
for the metadata file if it exists. In case of failure, we should rollback.
That's what this patch does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_rename() callback is vulnerable to symlink attacks because it
uses rename() which follows symbolic links in all path elements but the
rightmost one.
This patch simply transforms local_rename() into a wrapper around
local_renameat() which is symlink-attack safe.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_renameat() callback is currently a wrapper around local_rename()
which is vulnerable to symlink attacks.
This patch rewrites local_renameat() to have its own implementation, based
on local_opendir_nofollow() and renameat().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_lstat() callback is vulnerable to symlink attacks because it
calls:
(1) lstat() which follows symbolic links in all path elements but the
rightmost one
(2) getxattr() which follows symbolic links in all path elements
(3) local_mapped_file_attr()->local_fopen()->openat(O_NOFOLLOW) which
follows symbolic links in all path elements but the rightmost
one
This patch converts local_lstat() to rely on opendir_nofollow() and
fstatat(AT_SYMLINK_NOFOLLOW) to fix (1), fgetxattrat_nofollow() to
fix (2).
A new local_fopenat() helper is introduced as a replacement to
local_fopen() to fix (3). No effort is made to factor out code
because local_fopen() will be dropped when all users have been
converted to call local_fopenat().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_readlink() callback is vulnerable to symlink attacks because it
calls:
(1) open(O_NOFOLLOW) which follows symbolic links for all path elements but
the rightmost one
(2) readlink() which follows symbolic links for all path elements but the
rightmost one
This patch converts local_readlink() to rely on open_nofollow() to fix (1)
and opendir_nofollow(), readlinkat() to fix (2).
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_truncate() callback is vulnerable to symlink attacks because
it calls truncate() which follows symbolic links in all path elements.
This patch converts local_truncate() to rely on open_nofollow() and
ftruncate() instead.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_statfs() callback is vulnerable to symlink attacks because it
calls statfs() which follows symbolic links in all path elements.
This patch converts local_statfs() to rely on open_nofollow() and fstatfs()
instead.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_utimensat() callback is vulnerable to symlink attacks because it
calls qemu_utimens()->utimensat(AT_SYMLINK_NOFOLLOW) which follows symbolic
links in all path elements but the rightmost one or qemu_utimens()->utimes()
which follows symbolic links for all path elements.
This patch converts local_utimensat() to rely on opendir_nofollow() and
utimensat(AT_SYMLINK_NOFOLLOW) directly instead of using qemu_utimens().
It is hence assumed that the OS supports utimensat(), i.e. has glibc 2.6
or higher and linux 2.6.22 or higher, which seems reasonable nowadays.
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_remove() callback is vulnerable to symlink attacks because it
calls:
(1) lstat() which follows symbolic links in all path elements but the
rightmost one
(2) remove() which follows symbolic links in all path elements but the
rightmost one
This patch converts local_remove() to rely on opendir_nofollow(),
fstatat(AT_SYMLINK_NOFOLLOW) to fix (1) and unlinkat() to fix (2).
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_unlinkat() callback is vulnerable to symlink attacks because it
calls remove() which follows symbolic links in all path elements but the
rightmost one.
This patch converts local_unlinkat() to rely on opendir_nofollow() and
unlinkat() instead.
Most of the code is moved to a separate local_unlinkat_common() helper
which will be reused in a subsequent patch to fix the same issue in
local_remove().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_lremovexattr() callback is vulnerable to symlink attacks because
it calls lremovexattr() which follows symbolic links in all path elements
but the rightmost one.
This patch introduces a helper to emulate the non-existing fremovexattrat()
function: it is implemented with /proc/self/fd which provides a trusted
path that can be safely passed to lremovexattr().
local_lremovexattr() is converted to use this helper and opendir_nofollow().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_lsetxattr() callback is vulnerable to symlink attacks because
it calls lsetxattr() which follows symbolic links in all path elements but
the rightmost one.
This patch introduces a helper to emulate the non-existing fsetxattrat()
function: it is implemented with /proc/self/fd which provides a trusted
path that can be safely passed to lsetxattr().
local_lsetxattr() is converted to use this helper and opendir_nofollow().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_llistxattr() callback is vulnerable to symlink attacks because
it calls llistxattr() which follows symbolic links in all path elements but
the rightmost one.
This patch introduces a helper to emulate the non-existing flistxattrat()
function: it is implemented with /proc/self/fd which provides a trusted
path that can be safely passed to llistxattr().
local_llistxattr() is converted to use this helper and opendir_nofollow().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_lgetxattr() callback is vulnerable to symlink attacks because
it calls lgetxattr() which follows symbolic links in all path elements but
the rightmost one.
This patch introduces a helper to emulate the non-existing fgetxattrat()
function: it is implemented with /proc/self/fd which provides a trusted
path that can be safely passed to lgetxattr().
local_lgetxattr() is converted to use this helper and opendir_nofollow().
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The local_open() and local_opendir() callbacks are vulnerable to symlink
attacks because they call:
(1) open(O_NOFOLLOW) which follows symbolic links in all path elements but
the rightmost one
(2) opendir() which follows symbolic links in all path elements
This patch converts both callbacks to use new helpers based on
openat_nofollow() to only open files and directories if they are
below the virtfs shared folder
This partly fixes CVE-2016-9602.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch opens the shared folder and caches the file descriptor, so that
it can be used to do symlink-safe path walk.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
When using the passthrough security mode, symbolic links created by the
guest are actual symbolic links on the host file system.
Since the resolution of symbolic links during path walk is supposed to
occur on the client side. The server should hence never receive any path
pointing to an actual symbolic link. This isn't guaranteed by the protocol
though, and malicious code in the guest can trick the server to issue
various syscalls on paths whose one or more elements are symbolic links.
In the case of the "local" backend using the "passthrough" or "none"
security modes, the guest can directly create symbolic links to arbitrary
locations on the host (as per spec). The "mapped-xattr" and "mapped-file"
security modes are also affected to a lesser extent as they require some
help from an external entity to create actual symbolic links on the host,
i.e. another guest using "passthrough" mode for example.
The current code hence relies on O_NOFOLLOW and "l*()" variants of system
calls. Unfortunately, this only applies to the rightmost path component.
A guest could maliciously replace any component in a trusted path with a
symbolic link. This could allow any guest to escape a virtfs shared folder.
This patch introduces a variant of the openat() syscall that successively
opens each path element with O_NOFOLLOW. When passing a file descriptor
pointing to a trusted directory, one is guaranteed to be returned a
file descriptor pointing to a path which is beneath the trusted directory.
This will be used by subsequent patches to implement symlink-safe path walk
for any access to the backend.
Symbolic links aren't the only threats actually: a malicious guest could
change a path element to point to other types of file with undesirable
effects:
- a named pipe or any other thing that would cause openat() to block
- a terminal device which would become QEMU's controlling terminal
These issues can be addressed with O_NONBLOCK and O_NOCTTY.
Two helpers are introduced: one to open intermediate path elements and one
to open the rightmost path element.
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
(renamed openat_nofollow() to relative_openat_nofollow(),
assert path is relative and doesn't contain '//',
fixed side-effect in assert, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
If these functions fail, they should not change *fs. Let's use local
variables to fix this.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
These functions are always called indirectly. It really doesn't make sense
for them to sit in a header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This patchset adds the throttle support for the 9p-local driver.
For now this functionality can be enabled only through qemu cli options.
QMP interface and support to other drivers need further extensions.
To make it simple for other 9p drivers, the throttle code has been put in
separate files.
Signed-off-by: Pradeep Jagadeesh <pradeep.jagadeesh@huawei.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
(pass extra NULL CoMutex * argument to qemu_co_queue_wait(),
added options to qemu-options.hx, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
In this case, we are marshaling an error status instead of the errno value.
Reorganize the out and out_nofid labels to look like all the other cases.
Coverity reports this because the "err = -ENOENT" and "err = -EINVAL"
assignments above are dead, overwritten by the call to pdu_marshal.
(Coverity issues CID1348512 and CID1348513)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(also open-coded the success path since locking is a nop for us, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
Don't truncate the multiplication and do a 64 bit one instead
because the result is stored in a 64 bit variable.
This fixes a similar coverity warning to commits 237a8650d6 and
4382fa6554, in a similar way, and is the final third of the fix for
coverity CID 1167561 (hopefully!).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The register_read() and register_write() functions expect a bitmask argument.
To avoid duplicated code, a new inlined function register_enabled_mask() is
introduced.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The "qemu,register" device needs to be wired up in source code, there
is no way the user can make any real use of this device with the
"-device" parameter or the "device_add" monitor command yet.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The "or-irq" device needs to be wired up in source code, there is no
way the user can make any real use of this device with the "-device"
parameter or the "device_add" monitor command yet.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We'll add a variant which accepts dmabufs soon. Change
the name so we can easily disturgish the two variants.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1487669841-13668-2-git-send-email-kraxel@redhat.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYs072AAoJEDNgw/dBGhJfJNMH/iPNHzrZLRilU6CceYpNQW1Z
262rITUXBZ04vVhNjdIU6OZDjD12eY67eznfapsNNJPSNNR7UUMa8dymFZfBxgRL
Kl9jciJKhWUBdzn8qkvP2umXA9I6NZs+OJbSz8vIYVEX8mF8EaYNLGP40J+4qc+X
2GByZRu5yoYe5Ex1hNgdzPGPlyvJwymu0y7WW0gDPCrKtSSGz7NRGA9S2dvbFGQb
kNnkkS2aEkbt8fDWsTkcKVog3jFNfBzdEYUJel237+dMqnepFt5V1UWFANznb7Xp
pmdOWYhWntvi8ONwJW+RRWe4Mes2ySfqelmVD602dreuIRkX1bHBWkXA3S8pSmM=
=2VrG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/artyom/tags/pull-sun4v-20170226' into staging
Pull request for Niagara patches 2017 02 26
# gpg: Signature made Sun 26 Feb 2017 21:56:06 GMT
# gpg: using RSA key 0x3360C3F7411A125F
# gpg: Good signature from "Artyom Tarasenko <atar4qemu@gmail.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2AD8 6149 17F4 B2D7 05C0 BB12 3360 C3F7 411A 125F
* remotes/artyom/tags/pull-sun4v-20170226:
niagara: check if a serial port is available
niagara: fail if a firmware file is missing
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
fail if a firmware file is missing and not qtest_enabled(),
the later is necessary to allow some basic tests if
firmware is not available
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
CHanges:
* Add the Boston board with fixing the make check issue on 32-bit hosts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)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=xOs6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/yongbok/tags/mips-20170224-2' into staging
MIPS patches 2017-02-24-2
CHanges:
* Add the Boston board with fixing the make check issue on 32-bit hosts.
# gpg: Signature made Fri 24 Feb 2017 11:43:45 GMT
# gpg: using RSA key 0x2238EB86D5F797C2
# gpg: Good signature from "Yongbok Kim <yongbok.kim@imgtec.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 8600 4CF5 3415 A5D9 4CFA 2B5C 2238 EB86 D5F7 97C2
* remotes/yongbok/tags/mips-20170224-2:
hw/mips: MIPS Boston board support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- cleanups, fixes and improvements
- program check loop detection (useful with the corresponding kernel
patch)
- wire up virtio-crypto for ccw
- and finally support many virtqueues for virtio-ccw
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYr/qXAAoJEN7Pa5PG8C+vzSYP+wR/mA4wmXh0Jj8zzxeJaeQa
UNNwR7Ege4KjdL0DKXw/Uy2S/H2qGZvD4cb3JLIwp15BSilmcxRGS+v18ooBuRtx
X8+W2peH/Ldk4SAGbfXyRR4EXom4ZmmHtgdoWYPUhgq2BimH1vBcY06uHOkJ4zTP
vBfpmvKL53SjjHF6b9NmlprSDrn8cbQgqqxTWc0YL0aEcFTcxpBfr98dCfrNfk8b
k6f324hY+3YC7rdvLAsBx3tNjDmEoEh4aidGyECKOWiy2Bt2hQ/ZhxVUk7cFV30M
F0mttRJSxuBY9xYfmuxTKkm2ttIH0BiOhFmE5+YEj7ot+iqBslyYHR2prkZC66v+
wQ9Ynx8ys0ec/IkHx2uIt8iOdAiq/K5gJkyjEw6ekg70OOGrTtyv5y6G9FOc4B4W
ms7eUnhIgr5rEv/oQgCSgCUlAUm6MWW/BtffqmKZ7M2/7l8Y3T1U4f9383sKZtIT
7xr/AtV30yH695r+bllEljIjgMU5EWUDpA2kBCC6tzJQ0KYSoICSGloxKNEK3Z6X
EsYby7YjLArTlvsLJ4y2k/BPzcM4IYJX9NDjCmMRpR2I46Nb35uwR73EZx6JS6fw
dKmdx0qSZbaMbmwIJZzVz4kzG9z6gePkCvaEmPa99ZgnaZ0igm4y5W6Q8fLEn1Jz
zy277Wciim5mnZWuJAbl
=uM3N
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170224' into staging
A selection of s390x patches:
- cleanups, fixes and improvements
- program check loop detection (useful with the corresponding kernel
patch)
- wire up virtio-crypto for ccw
- and finally support many virtqueues for virtio-ccw
# gpg: Signature made Fri 24 Feb 2017 09:19:19 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170224:
s390x/css: handle format-0 TIC CCW correctly
s390x/arch_dump: pass cpuid into notes sections
s390x/arch_dump: use proper note name and note size
virtio-ccw: support VIRTIO_QUEUE_MAX virtqueues
s390x: bump ADAPTER_ROUTES_MAX_GSI
virtio-ccw: check flic->adapter_routes_max_batch
s390x: add property adapter_routes_max_batch
virtio-ccw: Check the number of vqs in CCW_CMD_SET_IND
virtio-ccw: add virtio-crypto-ccw device
virtio-ccw: handle virtio 1 only devices
s390x/flic: fail migration on source already
s390x/kvm: detect some program check loops
s390x/s390-virtio: get rid of DPRINTF
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=o8eA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-util-2017-02-23' into staging
option cutils: Fix and clean up number conversions
# gpg: Signature made Thu 23 Feb 2017 19:41:17 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-util-2017-02-23: (24 commits)
option: Fix checking of sizes for overflow and trailing crap
util/cutils: Change qemu_strtosz*() from int64_t to uint64_t
util/cutils: Return qemu_strtosz*() error and value separately
util/cutils: Let qemu_strtosz*() optionally reject trailing crap
qemu-img: Wrap cvtnum() around qemu_strtosz()
test-cutils: Drop suffix from test_qemu_strtosz_simple()
test-cutils: Use qemu_strtosz() more often
util/cutils: Drop QEMU_STRTOSZ_DEFSUFFIX_* macros
util/cutils: New qemu_strtosz()
util/cutils: Rename qemu_strtosz() to qemu_strtosz_MiB()
util/cutils: New qemu_strtosz_metric()
test-cutils: Cover qemu_strtosz() around range limits
test-cutils: Cover qemu_strtosz() with trailing crap
test-cutils: Cover qemu_strtosz() invalid input
test-cutils: Add missing qemu_strtosz()... endptr checks
option: Fix to reject invalid and overflowing numbers
util/cutils: Clean up control flow around qemu_strtol() a bit
util/cutils: Clean up variable names around qemu_strtol()
util/cutils: Rename qemu_strtoll(), qemu_strtoull()
util/cutils: Rewrite documentation of qemu_strtol() & friends
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CIRRUS_BLTMODE_MEMSYSSRC blits do NOT check blit destination
and blit width, at all. Oops. Fix it.
Security impact: high.
The missing blit destination check allows to write to host memory.
Basically same as CVE-2014-8106 for the other blit variants.
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The arm_reset_cpu/set_cpu_on/set_cpu_off() functions do their work
asynchronously in the target vCPUs context. As a result we need to
ensure the SRC_SCR reset bits correctly report the reset status at the
right time. To do this we defer the clearing of the bit with an async
job which will run after the work queued by ARM powerctl functions.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This finally allows TCG to benefit from the iothread introduction: Drop
the global mutex while running pure TCG CPU code. Reacquire the lock
when entering MMIO or PIO emulation, or when leaving the TCG loop.
We have to revert a few optimization for the current TCG threading
model, namely kicking the TCG thread in qemu_mutex_lock_iothread and not
kicking it in qemu_cpu_kick. We also need to disable RAM block
reordering until we have a more efficient locking mechanism at hand.
Still, a Linux x86 UP guest and my Musicpal ARM model boot fine here.
These numbers demonstrate where we gain something:
20338 jan 20 0 331m 75m 6904 R 99 0.9 0:50.95 qemu-system-arm
20337 jan 20 0 331m 75m 6904 S 20 0.9 0:26.50 qemu-system-arm
The guest CPU was fully loaded, but the iothread could still run mostly
independent on a second core. Without the patch we don't get beyond
32206 jan 20 0 330m 73m 7036 R 82 0.9 1:06.00 qemu-system-arm
32204 jan 20 0 330m 73m 7036 S 21 0.9 0:17.03 qemu-system-arm
We don't benefit significantly, though, when the guest is not fully
loading a host CPU.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <1439220437-23957-10-git-send-email-fred.konrad@greensocs.com>
[FK: Rebase, fix qemu_devices_reset deadlock, rm address_space_* mutex]
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[EGC: fixed iothread lock for cpu-exec IRQ handling]
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: -smp single-threaded fix, clean commit msg, BQL fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
[PM: target-arm changes]
Acked-by: Peter Maydell <peter.maydell@linaro.org>
This pull request has:
* Yet more POWER9 instruction implementations
* Some extensions to the softfloat code which are necesssary for
some of those instructions
* Some preliminary patches in preparation for POWER9 softmmu
implementation
* Igor Mammedov's cleanups to unify hotplug cpu handling across
architectures
* Assorted bugfixes
The softfloat and cpu hotplug changes aren't entirely ppc specific (in
fact the hotplug stuff contains some pc specific patches). However
they're included here because ppc is one of the main beneficiaries,
and the series depend on some ppc specific patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bsJJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170222' into staging
ppc patch queue for 2017-02-22
This pull request has:
* Yet more POWER9 instruction implementations
* Some extensions to the softfloat code which are necesssary for
some of those instructions
* Some preliminary patches in preparation for POWER9 softmmu
implementation
* Igor Mammedov's cleanups to unify hotplug cpu handling across
architectures
* Assorted bugfixes
The softfloat and cpu hotplug changes aren't entirely ppc specific (in
fact the hotplug stuff contains some pc specific patches). However
they're included here because ppc is one of the main beneficiaries,
and the series depend on some ppc specific patches.
# gpg: Signature made Wed 22 Feb 2017 06:29:47 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170222: (43 commits)
hw/ppc/ppc405_uc.c: Avoid integer overflows
hw/ppc/spapr: Check for valid page size when hot plugging memory
target-ppc: fix Book-E TLB matching
hw/net/spapr_llan: 6 byte mac address device tree entry
machine: replace query_hotpluggable_cpus() callback with has_hotpluggable_cpus flag
machine: unify [pc_|spapr_]query_hotpluggable_cpus() callbacks
spapr: reuse machine->possible_cpus instead of cores[]
change CPUArchId.cpu type to Object*
pc: pass apic_id to pc_find_cpu_slot() directly so lookup could be done without CPU object
pc: calculate topology only once when possible_cpus is initialised
pc: move pcms->possible_cpus init out of pc_cpus_init()
machine: move possible_cpus to MachineState
hw/pci-host/prep: Do not use hw_error() in realize function
target/ppc/POWER9: Direct all instr and data storage interrupts to the hypv
target/ppc/POWER9: Adapt LPCR handling for POWER9
target/ppc/POWER9: Add ISAv3.00 MMU definition
target/ppc: Fix LPCR DPFD mask define
target-ppc: Add xscvqpudz and xscvqpuwz instructions
target-ppc: Implement round to odd variants of quad FP instructions
softfloat: Add float128_to_uint32_round_to_zero()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For TIC CCW, bit positions 8-32 of the format-1 CCW must contain zeros;
otherwise, a program-check condition is generated. For format-0 TIC CCWs,
bits 32-63 are ignored.
To convert TIC from format-0 CCW to format-1 CCW correctly, let's clear
bits 8-32 to guarantee compatibility.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The maximal number of virtqueues per device can be limited on a per
transport basis. For virtio-ccw this limit is defined by
VIRTIO_CCW_QUEUE_MAX, however the limitation used to come form the
number of adapter routes supported by flic (via notifiers).
Recently the limitation of the flic was adjusted so that it can
accommodate VIRTIO_QUEUE_MAX queues, and is in the meanwhile checked for
separately too.
Let us remove the transport specific limitation of virtio-ccw by
dropping VIRTIO_CCW_QUEUE_MAX and using VIRTIO_QUEUE_MAX instead.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's increase ADAPTER_ROUTES_MAX_GSI to VIRTIO_QUEUE_MAX which is the
largest demand foreseeable at the moment. Let us add a compatibility
macro for the previous machines so client code can maintain backwards
migration compatibility
To not mess up migration compatibility for virtio-ccw
VIRTIO_CCW_QUEUE_MAX is left at it's current value, and will be dropped
when virtio-ccw is converted to use the capability of the flic
introduced by this patch.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently VIRTIO_CCW_QUEUE_MAX is defined as ADAPTER_ROUTES_MAX_GSI.
That is when checking queue max we implicitly check the constraint
concerning the number of adapter routes. This won't be satisfactory any
more (due to backward migration considerations) if ADAPTER_ROUTES_MAX_GSI
changes (ADAPTER_ROUTES_MAX_GSI is going to change because we want to
support up to VIRTIO_QUEUE_MAX queues per virtio-ccw device).
Let us introduce a check on a recently introduce flic property which
gives us the compatibility machine aware limit on adapter routes.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To make virtio-ccw supports more that 64 virtqueues we will have to
increase ADAPTER_ROUTES_MAX_GSI which is currently limiting the number if
possible adapter routes. Of course increasing the number of supported
routes can break backwards migration.
Let us introduce a compatibility property adapter_routes_max_batch so
client code can use the some old limit if in compatibility mode and
retain the migration compatibility.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We cannot support more than 64 virtqueues with the 64 bits provided by
classic indicators. If a driver tries to setup classic indicators
(which it is free to do even for virtio-1 devices) for a device with
more than 64 virtqueues, we should reject the attempt so that the
driver does not end up with an unusable device.
This is in preparation for bumping the number of supported virtqueues
on the ccw transport.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Wire up virtio-crypto for the CCW based VIRTIO.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
As a preparation for wiring-up virtio-crypto, the first non-transitional
virtio device on the ccw transport, let us introduce a mechanism for
disabling revision 0. This is more or less equivalent with disabling
legacy as revision 0 is legacy only, and legacy drivers use the revision
0 exclusively.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Current code puts a 'FLIC_FAILED' marker into the migration stream
to indicate something went wrong while saving flic state and fails
load if it encounters that marker. VMState's put routine recently
gained the ability to return error codes (but did not wire it up
yet).
In order to be able to reap the benefits of returning an error and
failing migration on the source already once this gets wired up
in core, return an error in addition to storing 'FLIC_FAILED'.
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
The DPRINTF approach is likely to introduce bitrot, and the preferred
way for debugging is tracing anyway. Fortunately, there are no users
(left), so nuke it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will permit its use in parse_option_size().
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Kevin Wolf <kwolf@redhat.com> (supporter:Block layer core)
Cc: Max Reitz <mreitz@redhat.com> (supporter:Block layer core)
Cc: qemu-block@nongnu.org (open list:Block layer core)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1487708048-2131-24-git-send-email-armbru@redhat.com>
This makes qemu_strtosz(), qemu_strtosz_mebi() and
qemu_strtosz_metric() similar to qemu_strtoi64(), except negative
values are rejected.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Kevin Wolf <kwolf@redhat.com> (supporter:Block layer core)
Cc: Max Reitz <mreitz@redhat.com> (supporter:Block layer core)
Cc: qemu-block@nongnu.org (open list:Block layer core)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1487708048-2131-23-git-send-email-armbru@redhat.com>
Change the qemu_strtosz() & friends to return -EINVAL when @endptr is
null and the conversion doesn't consume the string completely.
Matches how qemu_strtol() & friends work.
Only test_qemu_strtosz_simple() passes a null @endptr. No functional
change there, because its conversion consumes the string.
Simplify callers that use @endptr only to fail when it doesn't point
to '\0' to pass a null @endptr instead.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Kevin Wolf <kwolf@redhat.com> (supporter:Block layer core)
Cc: Max Reitz <mreitz@redhat.com> (supporter:Block layer core)
Cc: qemu-block@nongnu.org (open list:Block layer core)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1487708048-2131-22-git-send-email-armbru@redhat.com>
With qemu_strtosz(), no suffix means mebibytes. It's used rarely.
I'm going to add a similar function where no suffix means bytes.
Rename qemu_strtosz() to qemu_strtosz_MiB() to make the name
qemu_strtosz() available for the new function.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1487708048-2131-16-git-send-email-armbru@redhat.com>
Xtensa core may have a number of RAM and ROM areas configured. Record
their size and location from the core configuration overlay and
instantiate them as RAM regions in the SIM machine.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This reverts commit d3473e147a.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split xhci properties into common and nec specific.
Move the backward compat flags to nec, so the new qemu-xhci
devices doesn't carry on the compatibiity stuff.
Move the msi/msix switches too and just enable msix for qemu-xhci.
Also move the intrs and slots properties. Wasn't a great idea to
make them configurable in the first place, nobody needs this.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1487663432-10410-1-git-send-email-kraxel@redhat.com
It should return 1 if an error occurs when reading td.
This will avoid an infinite loop issue in ohci_service_ed_list.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1487760990-115925-1-git-send-email-liqiang6-s@360.cn
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Curiously, unrealize() is not being used, but it seems more
appropriate than handle_destroy() together with realize(). It is more
ubiquitous destroy name in qemu code base and may throw errors.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20170221141451.28305-25-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Regardless of running in UPT or legacy mode, the guest igd
drivers may attempt to use stolen memory, however only legacy
mode has BIOS support for reserving stolen memmory in the
guest VM. We zero out the stolen memory size in all cases,
then guest igd driver won't use stolen memory.
In legacy mode, user could use x-igd-gms option to specify the
amount of stolen memory which will be pre-allocated and reserved
by bios for igd use.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99028https://bugs.freedesktop.org/show_bug.cgi?id=99025
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Tested-by: Terrence Xu <terrence.xu@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since commit 4bb571d857 ("pci/pcie: don't assume cap id 0 is
reserved") removes the internal use of extended capability ID 0, the
comment here becomes invalid. However, peeling back the onion, the
code is still correct and we still can't seed the capability chain
with ID 0, unless we want to muck with using the version number to
force the header to be non-zero, which is much uglier to deal with.
The comment also now covers some of the subtleties of using cap ID 0,
such as transparently indicating absence of capabilities if none are
added. This doesn't detract from the correctness of the referenced
commit as vfio in the kernel also uses capability ID zero to mask
capabilties. In fact, we should skip zero capabilities precisely
because the kernel might also expose such a capability at the head
position and re-introduce the problem.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Currently we ignore this error, report it with error_reportf_err()
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
qobject_to_qdict(obj) returns NULL when obj isn't a QDict. Check
that instead of qobject_type(obj) == QTYPE_QDICT.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487363905-9480-8-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
When performing clock calculations, the ppc405_uc code
has several places where it multiplies together two
32-bit variables and assigns the result to a 64-bit
variable. This doesn't quite do what is intended because
C will compute a 32-bit multiply result. Add casts to
ensure we don't truncate the result.
(Spotted by Coverity, CID 1005504, 1005505.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER, the valid page sizes that the guest can use are bound
to the CPU and not to the memory region. QEMU already has some
fancy logic to find out the right maximum memory size to tell
it to the guest during boot (see getrampagesize() in the file
target/ppc/kvm.c for more information).
However, once we're booted and the guest is using huge pages
already, it is currently still possible to hot-plug memory regions
that does not support huge pages - which of course does not work
on POWER, since the guest thinks that it is possible to use huge
pages everywhere. The KVM_RUN ioctl will then abort with -EFAULT,
QEMU spills out a not very helpful error message together with
a register dump and the user is annoyed that the VM unexpectedly
died.
To avoid this situation, we should check the page size of hot-plugged
DIMMs to see whether it is possible to use it in the current VM.
If it does not fit, we can print out a better error message and
refuse to add it, so that the VM does not die unexpectely and the
user has a second chance to plug a DIMM with a matching memory
backend instead.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1419466
Signed-off-by: Thomas Huth <thuth@redhat.com>
[dwg: Fix a build error on 32-bit builds with KVM]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr-vlan device in QEMU has always presented it's MAC address in
the device tree as an 8 byte value, even though PAPR requires it to be
6 bytes. This is because, at the time, AIX required the value to be 8
bytes. However, modern versions of AIX support the (correct) 6
byte value so they no longer require the workaround.
It would be neatest to always provide a 6 byte value but that would
cause a problem with old Linux kernel ibmveth drivers, so the old 8
byte value is still presented when necessary.
Since commit 13f85203e (3.10, May 2013) the driver has been able to
handle 6 or 8 byte addresses so versions after that don't need to be
considered specially.
Drivers from kernels before that can also handle either type of
address, but not always:
* If the first byte's lowest bits are 10, the address must be 6 bytes.
* Otherwise, the address must be 8 bytes.
(The two bits in question are significant in a MAC address: they
indicate a locally-administered unicast address.)
So to maintain compatibility the old 8 byte value is presented when
the lowest two bits of the first byte are not 10.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Generic helper machine_query_hotpluggable_cpus() replaced
target specific query_hotpluggable_cpus() callbacks so
there is no need in it anymore. However inon NULL callback
value is used to detect/report hotpluggable cpus support,
therefore it can be removed completely.
Replace it with MachineClass.has_hotpluggable_cpus boolean
which is sufficient for the task.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All callbacks FOO_query_hotpluggable_cpus() are practically
the same except of setting vcpus_count to different values.
Convert them to a generic machine_query_hotpluggable_cpus()
callback by moving vcpus_count initialization to per machine
specific callback possible_cpu_arch_ids().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace SPAPR specific cores[] array with generic
machine->possible_cpus and store core objects there.
It makes cores bookkeeping similar to x86 cpus and
will allow to unify similar code.
It would allow to replace cpu_index based NUMA node
mapping with iproperty based one (for -device created
cores) since possible_cpus carries board defined
topology/layout.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
so it could be reused for SPAPR cores as well
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fill in CpuInstanceProperties once at board init time and
just copy them whenever query_hotpluggable_cpus() is called.
It will keep topology info always available without need
to recalculate it every time it's needed.
Considering it has NUMA node id, it will be used to keep
NUMA node to cpu mapping instead of numa_info[i].node_cpu
bitmasks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
possible_cpus could be initialized earlier then cpu objects,
i.e. when -smp is parsed so move init code to possible_cpu_arch_ids()
interface func and do initialization on the first call.
it should help later with making -numa cpu/-smp parsing a machine state
properties.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
so that it would be possible to reuse it with
spapr/virt-aarch64 targets.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
hw_error() is for CPU related errors only (it prints out a
register dump and calls abort()), so we should not use it
if we just failed to load the bios image. Apart from that,
realize() functions should not exit directly but always set
the errp with error_setg() in case of errors instead.
Additionally, move some code around and delete the bios memory
subregion again in case of such an error, so that we leave a
clean state when returning to the caller.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last byte of the option vector was missing due to an off-by-one
error. Without this fix, client architecture support negotiation will
fail because the last byte of option vector 5, which contains the MMU
support, will be missed.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
error_report() already puts a prefix with the program name in front
of the error strings, so the "qemu:" prefix is not necessary here
anymore.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_core_unplug() were essentially spapr_core_unplug_request()
handler that requested CPU removal and registered callback
which did actual cpu core removali but it was called from
spapr_machine_device_unplug() which is intended for actual object
removal. Commit (cf632463 spapr: Memory hot-unplug support)
sort of fixed it introducing spapr_machine_device_unplug_request()
and calling spapr_core_unplug() but it hasn't renamed callback and
by mistake calls it from spapr_machine_device_unplug().
However spapr_machine_device_unplug() isn't ever called for
cpu core since spapr_core_release() doesn't follow expected
hotunplug call flow which is:
1: device_del() ->
hotplug_handler_unplug_request() ->
set destroy_cb()
2: destroy_cb() ->
hotplug_handler_unplug() ->
object_unparent // actual device removal
Fix it by renaming spapr_core_unplug() to spapr_core_unplug_request()
which is called from spapr_machine_device_unplug_request() and
making spapr_core_release() call hotplug_handler_unplug() which
will call spapr_machine_device_unplug() -> spapr_core_unplug()
to remove cpu core.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reveiwed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_core_pre_plug/spapr_core_plug/spapr_core_unplug() are managing
wiring CPU core into spapr machine state and not internal CPU core state.
So move them from spapr_cpu_core.c to spapr.c where other similar
(spapr_memory_[foo]plug()) callbacks are located, which also matches
x86 target practice.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Split off destroying VCPU threads from drc callback
spapr_core_release() into new spapr_cpu_core_unrealizefn()
which takes care of internal cpu core state cleanup (i.e.
VCPU threads) and is called when object_unparent(core)
is called.
That leaves spapr_core_release() only with board mgmt
code, which will be moved to board related file in
follow up patch along with the rest on hotplug callbacks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Add support for emulating the Xilinx AXI Root Port Bridge for PCI
Express as described by Xilinx' PG055 document. This is a PCIe
controller that can be used with certain series of Xilinx FPGAs, and is
used on the MIPS Boston board which will make use of this code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[yongbok.kim@imgtec.com:
removed returning on !level,
updated IRQ connection with GPIO logic,
moved xilinx_pcie_init() to boston.c
replaced stw_le_p() with pci_set_word()
and other cosmetic changes]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Introduce support for loading Flattened Image Trees, as used by modern
U-Boot. FIT images are essentially flattened device tree files which
contain binary images such as kernels, FDTs or ramdisks along with one
or more configuration nodes describing boot configurations.
The MIPS Boston board typically boots kernels in the form of FIT images,
and will make use of this code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[yongbok.kim@imgtec.com:
fixed potential memory leaks,
isolated building option]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
If the GIC interrupt mask is changed by a write to the smask (set mask)
or rmask (reset mask) registers, we need to re-evaluate the state of the
pins/IRQs fed to the CPU. Without doing so we risk leaving a pin high
despite the interrupt that led to that state being masked, or losing
interrupts if an already pending interrupt is unmasked.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Provide a new function mips_gictimer_get_freq() which returns the
frequency at which a GIC timer will count. This will be useful for
boards which perform setup based upon this frequency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Support moving the GCR base address & updating the CPU's CP0 CMGCRBase
register appropriately. This is required if a platform needs to move its
GCRs away from other memory, as the MIPS Boston development board does
to avoid its flash memory.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
-----BEGIN PGP SIGNATURE-----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=/97H
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-block-2017-02-21' into staging
Changes to -drive without if= and with if=scsi
# gpg: Signature made Tue 21 Feb 2017 12:22:35 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-block-2017-02-21:
hw/i386: Deprecate -drive if=scsi with PC machine types
hw: Deprecate -drive if=scsi with non-onboard HBAs
hw/scsi: Concentrate -drive if=scsi auto-create in one place
hw: Drop superfluous special checks for orphaned -drive
blockdev: Make orphaned -drive fatal
blockdev: Improve message for orphaned -drive
hw/arm/highbank: Default -drive to if=ide instead of if=scsi
hw: Default -drive to if=none instead of scsi when scsi cannot work
hw: Default -drive to if=none instead of ide when ide cannot work
hw/arm/cubieboard hw/arm/xlnx-ep108: Fix units_per_default_bus
hw: Default -drive to if=ide explicitly where it works
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PC machines (pc-q35-* pc-i440fx-* pc-* isapc xenfv) automatically
create lsi53c895a SCSI HBAs and SCSI devices to honor -drive if=scsi.
For giggles, try -drive if=scsi,bus=25,media=cdrom --- this makes QEMU
create 25 of them.
lsi53c895a is thoroughly obsolete (PCI Ultra2 SCSI, ca. 2000), and
currently has no maintainer in QEMU. megasas is a better choice,
except with old OSes that lack drivers. virtio-scsi is a much better
choice when you have a driver, but only (newish) Linux comes with one
in the box. There is no good default that works for all guests.
Encourage users to pick a non-obsolete SCSI HBA that works for them by
deprecating -drive if=scsi.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-4-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
Drives defined with if=scsi are also picked up by SCSI HBAs added with
-device, unlike other interface types. Deprecate this usage, as follows.
Create the frontends for onboard HBAs in machine initialization code,
exactly like we do for if=ide and other interface types. Change
scsi_legacy_handle_cmdline() to create a frontend only when it's still
missing, and warn that this usage is deprecated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-3-git-send-email-armbru@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
We've traditionally rejected orphans here and there, but not
systematically. For instance, the sun4m machines have an onboard SCSI
HBA (bus=0), and have always rejected bus>0. Other machines with an
onboard SCSI HBA don't.
Commit a66c9dc made all orphans trigger a warning, and the previous
commit turned this into an error. The checks "here and there" are now
redundant. Drop them.
Note that the one in mips_jazz.c was wrong: it rejected bus > MAX_FD,
but MAX_FD is the number of floppy drives per bus.
Error messages change from
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: Too many IDE buses defined (3 > 2)
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu: too many floppy drives
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu: too many SCSI bus
to
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: -drive if=ide,bus=2: machine type does not support if=ide,bus=2,unit=0
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu-system-mips64: -drive if=floppy,bus=2,id=fd1: machine type does not support if=floppy,bus=2,unit=0
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu-system-sparc: -drive if=scsi,bus=1: machine type does not support if=scsi,bus=1,unit=0
Cc: John Snow <jsnow@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-9-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
These machines have no onboard SCSI HBA, and no way to plug one.
-drive if=scsi therefore cannot work. They do have an onboard IDE
controller (sysbus-ahci), but fail to honor if=ide.
Change their default to if=ide, and add a TODO comment on what needs
to be done to actually honor -drive if=ide.
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-6-git-send-email-armbru@redhat.com>
Block backends defined with -drive if=scsi are meant to be picked up
by machine initialization code: a suitable frontend gets created and
wired up automatically.
if=scsi drives not picked up that way can still be used with -device
as if they had if=none, but that's unclean and best avoided. Unused
ones produce an "Orphaned drive without device" warning.
A few machine types default to if=scsi, even though they don't
actually have a SCSI HBA. This makes no sense. Change their default
to if=none. Affected machines:
* aarch64/arm: realview-pbx-a9 vexpress-a9 vexpress-a15 xilinx-zynq-a9
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <1487153147-11530-5-git-send-email-armbru@redhat.com>
Machine types cubieboard, xlnx-ep108, xlnx-zcu102 have an onboard AHCI
controller, but neglect to set their MachineClass member
units_per_default_bus = 1. This permits -drive if=ide,unit=1, which
makes no sense for AHCI. It also screws up index=N for odd N, because
it gets desugared to unit=1,bus=N/2
Doesn't really matter, because these machine types fail to honor
-drive if=ide. Add the missing units_per_default_bus = 1 anyway,
along with a TODO comment on what needs to be done for -drive if=ide.
Also set block_default_type = IF_IDE explicitly. It's currently the
default, but the next commit will change it to something more
sensible, and we want to keep the IF_IDE default for these three
machines. See also the previous commit.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <1487153147-11530-3-git-send-email-armbru@redhat.com>
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types default to if=ide, even though they don't actually
have an IDE controller. A future patch will change these defaults to
something more sensible. To prepare for it, this patch makes default
"ide" explicit for the machines that actually pick up if=ide drives:
* alpha: clipper
* arm/aarch64: spitz borzoi terrier tosa
* i386/x86_64: generic-pc-machine (with concrete subtypes pc-q35-*
pc-i440fx-* pc-* isapc xenfv)
* mips64el: fulong2e
* mips/mipsel/mips64el: malta mips
* ppc/ppc64: mac99 g3beige prep
* sh4/sh4eb: r2d
* sparc64: sun4u sun4v
Note that ppc64 machine powernv already sets an "ide" default
explicitly. Its IDE controller isn't implemented, yet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-2-git-send-email-armbru@redhat.com>
v2:
* Rebased to resolve scsi conflicts
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYrCroAAoJEJykq7OBq3PIpJAH/1nvSNr8IRrEWFXuHxHlwqXo
opt8PZm1BhKLwKoZ7qwttWk8oxWV+VBRZcnLnm1+chmIqzwbeUVo8nzFwPbv1kB3
2x3uLz+3Qn0uln9v43alK5mHZk7wpGCshFBn3jkxdltzZX9vIaG+8IkKsgkS+IiC
MkUPFfoY/wRQq+eyBvhe6xPHoIlKa++LeQdRQ4kayvaixW1dn4Hbvj/vLAAG1nKL
HcEtO3EddEgkIvX5yztOWNKvEPqcYes7Ki207CjH8GXj4Ygmn4dBebDq+GR0NYwm
EXERuJJiPEbSLFknffwioVfllWKCVwg7oFaIuz6ysxVGFwFZSdn83CTjK+FbtFU=
=k9gD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
Pull request
v2:
* Rebased to resolve scsi conflicts
# gpg: Signature made Tue 21 Feb 2017 11:56:24 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request: (24 commits)
coroutine-lock: make CoRwlock thread-safe and fair
coroutine-lock: add mutex argument to CoQueue APIs
coroutine-lock: place CoMutex before CoQueue in header
test-aio-multithread: add performance comparison with thread-based mutexes
coroutine-lock: add limited spinning to CoMutex
coroutine-lock: make CoMutex thread-safe
block: document fields protected by AioContext lock
async: remove unnecessary inc/dec pairs
aio-posix: partially inline aio_dispatch into aio_poll
block: explicitly acquire aiocontext in aio callbacks that need it
block: explicitly acquire aiocontext in bottom halves that need it
block: explicitly acquire aiocontext in callbacks that need it
block: explicitly acquire aiocontext in timers that need it
aio: push aio_context_acquire/release down to dispatching
qed: introduce qed_aio_start_io and qed_aio_next_io_cb
blkdebug: reschedule coroutine on the AioContext it is running on
coroutine-lock: reschedule coroutine on the AioContext it was running on
nbd: convert to use qio_channel_yield
io: make qio_channel_yield aware of AioContexts
io: add methods to set I/O handlers on AioContext
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All that CoQueue needs in order to become thread-safe is help
from an external mutex. Add this to the API.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-6-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-16-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-15-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
