This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the SiFive SPI controller model for the FU540 SoC.
The direct memory-mapped SPI flash mode is unsupported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This updates the flash information table to include various ISSI
flashes that are supported by upstream U-Boot and Linux kernel.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present when blk_pread() / blk_pwrite() fails, a guest error
is logged, but this is not really a guest error. Change to use
error_report() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1611026585-29971-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmA+SYcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpUAAIALa9WkjdxjZhb4FzP1OLBSTEISLEfrPE4Zk/
s5yY1wEDvH83D6fxTHv1B8tISwJ3RJn8ZhsP0c0Mb6stT7D33m7YfMFtNXBEfENX
gMgwdC2QxGMZXKGR+dIpxtYghjvuzAVN+e9w27C+s855JJ8y+chghtLuDJIbqpAk
QopftjiZix2bPYmrxlVw/A7inXL2jseJyYsgGAzIACmsGC70jK4Rk1vxrAF+2n15
D4qKOG3QLJXrfIVa8iDz/ojlVUmLWl8jnoE+oY+rjtckQHJKqodlJi5yeJxGEa3/
G7db+AIzEBge78dq7LBSJOTjoUFoQ+6Hv1QtKk2GcMKdEnsj0ng=
=NGys
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio,pci: bug fixes
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 02 Mar 2021 14:19:51 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
vhost: simplify vhost_dev_init() fail_busyloop label
hw/pci: Have safer pcie_bus_realize() by checking error path
virtio-net: handle zero mac for a vdpa peer
i386/acpi: restore device paths for pre-5.1 vms
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmA3tzQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMsngf+OkbgTDouxq3qnn1K89n6j2wKlAj0
qPP+57o1sv5u5MjX0BkawXCMJfvTKJaOt/Cs8S0FaPTehfR5H0T2tL76KZBEdlEP
/+V3EC0Qmd1S47LKIOuDkV15szvnccyjpgwaL7Osjb0Eh0SxeXd4pBTc3yYtkacu
zb/srZ63U2iJZr93QwGmEJjuW57WNym6QWXF3Mrg9PFXybkXFTGumB2vZMlQc+MN
RWPTUKZKAiIr/HfdvpIETXY+HzJhylvIQ8OVWtM3XDorl48OWcOat/jyeNEVYgG3
o+gxIRnfvIL+42GkmUFbOKLzT5SV6p9EYYGLTuE1kU7nc6HWoD0CdPxA3A==
=UBVO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging
* fix --enable-fuzzing linker failures (Alexander)
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
# gpg: Signature made Thu 25 Feb 2021 14:41:56 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini-gitlab/tags/for-upstream: (29 commits)
tcg/i386: rdpmc: fix the the condtions
chardev: do not use short form boolean options in non-QemuOpts character device descriptions
vl: deprecate -writeconfig
target/i386: Add bus lock debug exception support
qom/object.c: Fix typo
target/i386: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -vnc
docs: update to show preferred boolean syntax for -chardev
qemu-options: update to show preferred boolean syntax for -vnc
qemu-options: update to show preferred boolean syntax for -incoming
qemu-options: update to show preferred boolean syntax for -netdev
qemu-options: update to show preferred boolean syntax for -spice
qemu-options: update to show preferred boolean syntax for -chardev
gdbstub: use preferred boolean option syntax
char: don't fail when client is not connected
scsi: drop 'result' argument from command_complete callback
scsi-disk: pass guest recoverable errors through even for rerror=stop
scsi-disk: pass SCSI status to scsi_handle_rw_error
scsi: introduce scsi_sense_from_errno()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Requiring a conditional for every goto is tedious:
if (busyloop_timeout) {
goto fail_busyloop;
} else {
goto fail;
}
Move the conditional to into the fail_busyloop label so that it's safe
to jump to this label unconditionally.
This change makes the migrate_add_blocker() error case more consistent.
It jumped to fail_busyloop unconditionally whereas the memslots limits
error case was conditional.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210222114931.272308-1-stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While pci_bus_realize() currently does not use the Error* argument,
it would be an error to leave pcie_bus_realize() setting bus->flags
if pci_bus_realize() had failed.
Fix by using a local Error* and return early (propagating the error)
if pci_bus_realize() failed.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210201153700.618946-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some mlx vdpa devices with kernels at least up to 5.11 currently present
0 as their MAC address. This is because they have not been
pre-configured with a MAC: they have a learning bridge and only learn
the MAC once guest is up. Kernel patches and tools to allow programming
the MAC from host are being developed. For now - since these
combinations exist in the field - let's detect zero mac and just try to
proceed with the mac from the qemu command line.
This makes the guest use this MAC to send packets in turn teaching
the MAC to the card, and things work.
TODO:
report the actual MAC from QEMU commad line in the info message.
TODO:
detect that a (non-zero) hardware MAC does not match QEMU command line
and fail init.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20210225165506.18321-2-lulu@redhat.com>
mst: rewritten code comments, message printed and the commit log.
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Tested-by: Sean Mooney <smooney@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After fixing the _UID value for the primary PCI root bridge in
af1b80ae it was discovered that this change updates Windows
configuration in an incompatible way causing network configuration
failure unless DHCP is used. More details provided on the list:
https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg08484.html
This change reverts the _UID update from 1 to 0 for q35 and i440fx
VMs before version 5.2 to maintain the original behaviour when
upgrading.
Cc: qemu-stable@nongnu.org
Cc: qemu-devel@nongnu.org
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-Id: <20210301195919.9333-1-cheptsov@ispras.ru>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: af1b80ae56 ("i386/acpi: fix inconsistent QEMU/OVMF device paths")
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, recoverable sense values are only passed directly to the
guest only for rerror=report. However, when rerror/werror are 'stop'
we still don't want the host to be involved on every UNIT ATTENTION
(especially considered that the QMP event will not have enough information
to act on the report).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of fishing it from *r->status, just pass the SCSI status
as a positive value of the second parameter and an errno as a
negative value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new function is an extension of the switch statement in scsi-disk.c
which also includes the errno cases only found in sg_io_sense_from_errno.
This allows us to consolidate the errno handling.
Extracted from a patch by Hannes Reinecke <hare@suse.de>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When requested to ignore errors, just do nothing and let the
request complete normally. This means that the request will
be accounted correctly.
This is what commit 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore",
2018-10-19) was supposed to do:
Fixes: 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore", 2018-10-19)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If virtio_scsi_dataplane_start fails, there is a small window when it drops the
aio lock (in aio_wait_bh_oneshot) and the dataplane's AIO handler can
still run during that window.
This is done after the dataplane was marked as fenced, thus we use this flag
to avoid it doing any IO.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'enospc' is the default for -drive, but qemu allows user to set
drive option werror. If werror of scsi-generic is set to 'report'
by user, qemu will not allow vm to start.
This patch allow user to set werror as 'report' for scsi-generic.
Signed-off-by: Zihao Chang <changzihao1@huawei.com>
Reviewed-by: Fam Zheng <fam@euphon.net>
Message-Id: <20201103061240.1364-1-changzihao1@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tracepoints for SG_IO commands to allow for debugging
of SG_IO commands.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-4-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current code sets an infinite timeout on SG_IO requests,
causing the guest to stall if the host experiences a frame
loss.
This patch adds an 'io_timeout' parameter for SCSIDevice to
make the SG_IO timeout configurable, and also shortens the
default timeout to 30 seconds to avoid infinite stalls.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Declare PNP0C01 device to reserve MMCONFIG region to conform to the
spec better and play nice with guest BIOSes/OSes.
According to PCI Firmware Specification[0], MMCONFIG region must be
reserved by declaring a motherboard resource. It's optional to reserve
the region in memory map by Int 15 E820h or EFIGetMemoryMap.
Guest Linux checks if the MMCFG region is reserved by bios memory map
or ACPI resource. If it's not reserved, Linux falls back to legacy PCI
configuration access.
TDVF [1] [2] doesn't reserve MMCONFIG the region in memory map.
On the other hand OVMF reserves it in memory map without declaring a
motherboard resource. With memory map reservation, linux guest uses
MMCONFIG region. However it doesn't comply to PCI Firmware
specification.
[0] PCI Firmware specification Revision 3.2
4.1.2 MCFG Table Description table 4-2 NOTE 2
If the operating system does not natively comprehend reserving the
MMCFG region, The MMCFG region must e reserved by firmware. ...
For most systems, the mortheroard resource would appear at the root
of the ACPI namespace (under \_SB)...
The resource can optionally be returned in Int15 E820h or
EFIGetMemoryMap as reserved memory but must always be reported
through ACPI as a motherboard resource
[1] TDX: Intel Trust Domain Extension
https://software.intel.com/content/www/us/en/develop/articles/intel-trust-domain-extensions.html
[2] TDX Virtual Firmware
https://github.com/tianocore/edk2-staging/tree/TDVF
The change to DSDT is as follows.
@@ -68,32 +68,47 @@
If ((CDW3 != Local0))
{
CDW1 |= 0x10
}
CDW3 = Local0
}
Else
{
CDW1 |= 0x04
}
Return (Arg3)
}
}
+
+ Device (DRAC)
+ {
+ Name (_HID, "PNP0C01" /* System Board */) // _HID: Hardware ID
+ Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
+ {
+ DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x00000000, // Granularity
+ 0xB0000000, // Range Minimum
+ 0xBFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ 0x10000000, // Length
+ ,, , AddressRangeMemory, TypeStatic)
+ })
+ }
}
Scope (_SB)
{
Device (HPET)
{
Name (_HID, EisaId ("PNP0103") /* HPET System Timer */) // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
OperationRegion (HPTM, SystemMemory, 0xFED00000, 0x0400)
Field (HPTM, DWordAcc, Lock, Preserve)
{
VEND, 32,
PRD, 32
}
Method (_STA, 0, NotSerialized) // _STA: Status
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <6f686b45ce7bc43048c56dbb46e72e1fe51927e6.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
If SMM is not supported, ACPI fixed hardware doesn't support
legacy-mode. ACPI-only platform. Where SCI_EN in PM1_CNT register is
always set.
The bit tells OS legacy mode(SCI_EN cleared) or ACPI mode(SCI_EN set).
With the next patch (setting fadt.smi_cmd = 0 when smm isn't enabled),
guest Linux tries to switch to ACPI mode, finds smi_cmd = 0, and then
fails to initialize acpi subsystem. This patch proactively fixes it.
This patch changes guest ABI. To keep compatibility, use
"smm-compat" introduced by earlier patch. If the property is true,
disable new behavior.
ACPI spec 4.8.10.1 PM1 Event Grouping
PM1 Eanble Registers
> For ACPI-only platforms (where SCI_EN is always set)
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <500f62081626997e46f96377393d3662211763a8.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following patch will introduce incompatible behavior of SMM.
Introduce a property to keep the old behavior for compatibility.
To enable smm compat, use "-global ICH9-LPC.smm-compat=on" or
"-global PIIX4_PM.smm-compat=on"
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <47254ae0b8c6cc6945422978b6b2af2d213ef891.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
When check DMA support for device attached to pxb,
the cache coherency attribute need to be set.
This add _CCA attribute for pxb DSDT.
Fixes: 6f9765fbad ("acpi/gpex: Build tables for pxb")
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1612490205-48788-3-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
When the pcie slot is initialized, by default PCI_EXP_LNKSTA_DLLLA
(Data Link Layer Link Active) is set in PCI_EXP_LNKSTA
(Link Status) without checking if the slot is empty or not.
This is confusing for the kernel because as it sees the link is up
it tries to read the vendor ID and fails:
(From https://bugzilla.kernel.org/show_bug.cgi?id=211691)
[ 1.661105] pcieport 0000:00:02.2: pciehp: Slot Capabilities : 0x0002007b
[ 1.661115] pcieport 0000:00:02.2: pciehp: Slot Status : 0x0010
[ 1.661123] pcieport 0000:00:02.2: pciehp: Slot Control : 0x07c0
[ 1.661138] pcieport 0000:00:02.2: pciehp: Slot #0 AttnBtn+ PwrCtrl+ MRL- AttnInd+ PwrInd+ HotPlug+ Surprise+ Interlock+ NoCompl- IbPresDis- LLActRep+
[ 1.662581] pcieport 0000:00:02.2: pciehp: pciehp_get_power_status: SLOTCTRL 6c value read 7c0
[ 1.662597] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662703] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 1.662706] pcieport 0000:00:02.2: pciehp: pcie_enable_notification: SLOTCTRL 6c write cmd 1031
[ 1.662730] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662748] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662750] pcieport 0000:00:02.2: pciehp: Slot(0-2): Link Up
[ 2.896132] pcieport 0000:00:02.2: pciehp: pciehp_check_link_status: lnk_status = 2204
[ 2.896135] pcieport 0000:00:02.2: pciehp: Slot(0-2): No device found
[ 2.896900] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 2.896903] pcieport 0000:00:02.2: pciehp: pciehp_power_off_slot: SLOTCTRL 6c write cmd 400
[ 3.656901] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0009 from Slot Status
This is really a problem with virtio-net failover that hotplugs a VFIO
card during the boot process. The kernel can shutdown the slot while
QEMU is hotplugging it, and this likely ends by an automatic unplug of
the card. At the end of the boot sequence the card has disappeared.
To fix that, don't set the "Link Active" state in the init function, but
rely on the plug function to do it, as the mechanism has already been
introduced by 2f2b18f60b.
Fixes: 2f2b18f60b ("pcie: set link state inactive/active after hot unplug/plug")
Cc: zhengxiang9@huawei.com
Fixes: 3d67447fe7 ("pcie: Fill PCIESlot link fields to support higher speeds and widths")
Cc: alex.williamson@redhat.com
Fixes: b2101eae63 ("pcie: Set the "link active" in the link status register")
Cc: benh@kernel.crashing.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-5-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In failover_add_primary(), we search the id of the failover device by
scanning the list of the devices in the opts list to find a device with
a failover_pair_id equals to the id of the virtio-net device.
If the failover_pair_id is not found, QEMU ignores the primary
device silently (which also means it will not be hidden and
it will be enabled directly at boot).
After that, we search the id in the opts list to do a qdev_device_add()
with it. The device will be always found as otherwise we had exited
before, and thus the warning is never displayed.
Fix that by moving the error report to the first exit condition.
Also add a g_assert() to be sure the compiler will not complain
about a possibly NULL pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-4-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
failover_add_primary() calls qdev_device_add() and doesn't unref
the device. Because of that, when the device is unplugged a reference
is remaining and prevents the cleanup of the object.
This prevents to be able to plugin back the failover primary device,
with errors like:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
(qemu) device_del hostdev0
We can check with "info qtree" and "info pci" that the device has been removed, and then:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev1,bus=root.3,failover_pair_id=net0
Error: vfio 0000:41:00.0: device is already attached
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
qemu-kvm: Duplicate ID 'hostdev0' for device
Fixes: 21e8709b29 ("failover: Remove primary_dev member")
Cc: quintela@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-3-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Commit a1190ab628 has added a "allow_unplug_during_migration = true" at
the end of the main "if" block, so it is not needed to set it anymore
in the previous checking.
Remove it, to have only sub-ifs that check for needed conditions and exit
if one fails.
Fixes: 4f5b6a05a4 ("pci: add option for net failover")
Fixes: a1190ab628 ("migration: allow unplug during migration for failover devices")
Cc: jfreimann@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-2-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmAyqe0ACgkQ4+MsLN6t
wN5Vbw/7BbLUjqZzs4pDVUv4XXeSoVIP9fEmEUoxbVgb58cD6ZE6PeEN7fT+I++E
fTu6Fw2WTHrGOWGkHRSOAGIAz4DqSsLJ2Qub4SRThdWgl9NgAgPDV32L7hCSJNfJ
ejK9PL/B4dYS1RoRPULdrsiuKYsXcl/QBo99nQoa+0fquPQBnA3LlPJX7my9s2SB
QoTK29V4KjLnTf4ebFP9mOHm4Z96lzl7jITjRUg4g5fh/IH+qlWlDUtMV5n2EL2b
Jp798z1ydsEGHmM1O5xbjQixwZZYSgt+mjRn4fHH/mSLyfanJW/0pK1o6Ktl2zDC
Ks1N0RNMsCZrvPXkUz6h7i6rXJsxzh0e96CmzOqBbKMzKuozig8ZMhmQTEGEvzf5
cMxAKYJu95ndmRISV8p3fdsT/t0j08WZ5m3Syz/VqV57mVP3fj2yqiDXl1vwoPjM
O2zYgK1VOgVsr0GPcJ5bHxDvuzbPvCd7YE0RhK2eFKkYLjQz7SEtC8RzmkKXoYze
8nj7eBgG37vaPUGOyjZROOftrTXvqx6swB9kmQ38FrIfM/tZQYa54w4kFXF7nI06
HIdiPIXPv+xqfwYUcsMuE/Mq/cXMTlgUF6445FHJ2yhaySrsch7BDR6BOgOmiNkM
iXT0PdlS5P1J4y5HBzwQhrGslZGdXz+UsmF+zq4vgfbMul4VsoQ=
=g7Kx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-20210221' into staging
MIPS patches queue
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
# gpg: Signature made Sun 21 Feb 2021 18:43:57 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-20210221: (43 commits)
vt82c686: Fix superio_cfg_{read,write}() functions
vt82c686: Log superio_cfg unimplemented accesses
vt82c686: Simplify by returning earlier
vt82c686: Reduce indentation by returning early
vt82c686: Remove index field of SuperIOConfig
vt82c686: Move creation of ISA devices to the ISA bridge
vt82c686: Simplify vt82c686b_realize()
vt82c686: Make vt82c686b-pm an abstract base class and add vt8231-pm based on it
vt82c686: Set user_creatable=false for VT82C686B_PM
vt82c686: Fix up power management io base and config
vt82c686: Correctly reset all registers to default values on reset
vt82c686: Correct vt82c686-pm I/O size
vt82c686: Make vt82c686-pm an I/O tracing region
vt82c686: Fix SMBus IO base and configuration registers
vt82c686: Reorganise code
vt82c686: Move superio memory region to SuperIOConfig struct
target/mips: Use GPR move functions in gen_HILO1_tx79()
target/mips: Introduce gen_load_gpr_hi() / gen_store_gpr_hi() helpers
target/mips: Rename 128-bit upper halve GPR registers
target/mips: Promote 128-bit multimedia registers as global ones
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These functions are memory region callbacks so we have to check
against relative address not the mapped address.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 5/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 4/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
By returning earlier we can remove the 'can_write' boolean variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 3/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split patch original in 5, this is part 2/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove the separate index value from SuperIOConfig and store
the index at reg 0 which is reserved and returns 0 on read.
This simplifies the object state.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 1/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently the ISA devices that are part of the VIA south bridge,
superio chip are wired up by board code. Move creation of these ISA
devices to the VIA ISA bridge model so that board code does not need
to access ISA bus. This also allows vt82c686b-superio to be made
internal to vt82c686 which allows implementing its configuration via
registers in subseqent commits.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <bf9400cc8e4ddd3129aa5678de4d3cf38384805f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove unneeded variables and setting value to 0 on zero initialised
data and replace check for error with error_fatal. Rationalise loop
that sets PCI config header fields read only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <e4caf35ca10a68f5c74ae3f93fa0bcfa9457beea.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This device is part of the multifunction VIA superio/south bridge chip
so not useful in itself.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <d0a806fed5e8055aee4fcf5b2f4790e6dd0f9dc6.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
