DO_UPCAST is supposed to translate from the first member of a struct to
that struct, not from arbitrary ones. And it (usually) breaks the build
when neglecting this rule. Use container_of to fix the build breakage
and likely also the runtime behavior.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
aw: runtime behavior is actually the same, but clearly misuse of DO_UPCAST
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Blue Swirl reports that Clang doesn't like the structure we define to
avoid dynamic allocation for a number of calls to VFIO_DEVICE_SET_IRQS.
Adding an element after a variable sized type is a GNU extension.
Switch back to dynamic allocation, which really isn't a problem since
this is only done on interrupt setup changes.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Take what we've learned from pci-assign and apply it to vfio-pci.
On reset, disable previous interrupt config, perform a device
reset if available, re-enable INTx, and disable memory regions on
the device to prevent continuing DMA.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This was a misinterpretation of the spec, hardware doesn't get to
specify how many were actually enabled through this field.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We try to do lazy initialization of MSIX since we don't actually need
to setup anything until MSIX vectors start getting used. This leads
to problems if MSIX is enabled, but never used (we can end up trying
to re-enable INTx while it's still enabled). We also run into
problems trying to expand our reset function to tear down interrupts
as we can then get vector release notifications after we've released
data structures. By making explicit initialization and teardown we
can avoid both of these problems and behave more similar to bare
metal.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Occasionally we get regions added that overlap with existing mappings.
These always seems to be in the VGA ROM range. VFIO returns EBUSY
for these mapping attempts. We can try a little harder and assume
that the latest mapping is correct by removing any overlapping ranges
and retrying the original request.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We can't afford the overhead of switching out and back into mmap mode
around each interrupt, but we can do it lazily via a timer. On INTx
interrupt, disable the mmap'd memory regions and set a timer. On
every interrupt, push the timer out. If the timer expires and the
interrupt is no longer pending, switch back to mmap mode.
This has the benefit that things like graphics cards, which rarely or
never, fire an interrupt don't need manual user intervention to add
the x-intx=off parameter. They'll just remain in mmap mode until they
trigger an interrupt, and if they don't continue to regularly fire
interrupts, they'll switch back.
The default timeout is tuned for network cards so that a ping is just
enough to keep them in non-mmap mode, where they have much better
latency. It is tunable with an experimental option,
x-intx-mmap-timeout-ms. A value of 0 keeps the device in non-mmap
mode after the first interrupt.
It's possible we could look at the class code of devices and come up
with reasonable per-class defaults based on expected interrupt
frequency and latency. None of this is used for MSI interrupts and
also won't be used if we can bypass through KVM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
nc.link_down could not be migrated, this patch updates link_down in
virtio_post_load() to keep it coincident with real link status.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
This patch introduced e1000_post_load(), it will be called in the end of
migration. nc.link_down could not be migrated, this patch updates
link_down in e1000_post_load() to keep it coincident with real link
status.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Add a link status chang callback and change the link status bit in BMSR
& MSR accordingly. Tested in Linux/Windows guests.
The link status bit of MediaStatus is infered from BasicModeStatus,
they are inverse.
nc.link_down could not be migrated, this patch updates link_down in
rtl8139_post_load() to keep it coincident with real link status.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
With the next qemu version (1.3) we are going to bump the qxl device
revision to 4. The new features available require a recent spice-server
version, so raise up the bar. Otherwise we would end up with different
qxl revisions depending on the spice-server version installed, which
would be a major PITA when it comes to compat properties.
Clear out a big bunch of #ifdefs which are not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
As suggested by Paolo Bonzini, to avoid possible integer overflow issues.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This prevents a segfault later on when the device reset handler
tries to access a NULL ssd.worker since interface_attach_worker has
not been called.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Enables QXL_IO_FLUSH_SURFACES_ASYNC and QXL_IO_FLUSH_RELEASE
which are part of the qxl rev3 feature set.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This cleans up two additions of almost the same code in commits
511b13e2c9 and ccc2960d65. While at it, make error paths
consistent (always use 'break' instead of 'return').
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dunrong Huang <riegamaths@gmail.com>
Cc: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Don't try to be clever and skip displaysurface reinitialization in case
the size hasn't changed. Other parameters might have changed
nevertheless, for example depth or stride, resulting in rendering being
broken then.
Trigger: boot linux guest with vesafb, start X11, make sure both vesafb
and X11 use the display same resolution. Then watch X11 screen being
upside down.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* 'trivial-patches' of git://github.com/stefanha/qemu:
versatilepb: Use symbolic indices for ARM PIC
qdev: kill bogus comment
qemu-barrier: Fix compiler version check for future gcc versions
hw: Add missing 'static' attribute for QEMUMachine
cleanup useless return sentence
qemu-sockets: Fix compiler warning (regression for MinGW)
vnc: Fix spelling (hellmen -> hellman) in comment
slirp: Fix spelling in comment (enought -> enough, insure -> ensure)
tcg/arm: Use tcg_out_mov_reg rather than inline equivalent code
cpu: Add missing 'static' attribute to qemu_global_mutex
configure: Support empty target list (--target-list=)
hw: Fix return value check for bdrv_read, bdrv_write
* 'ppc-for-upstream' of git://repo.or.cz/qemu/agraf: (35 commits)
PPC: KVM: Fix BAT put
PPC: e500: Only expose even TLB sizes in initial TLB
ppc/pseries: Reset VPA registration on CPU reset
pseries: Don't test for MSR_PR for hypercalls under KVM
PPC: e500: calculate initrd_base like dt_base
PPC: e500: increase DTC_LOAD_PAD
device tree: simplify dumpdtb code
fdt: move dumpdtb interpretation code to device_tree.c
target-ppc: Remove unused power_mode field from cpu state
pseries: Set hash table size based on RAM size
pseries: Remove unnecessary locking from PAPR hash table hcalls
ppc405_uc: Fix buffer overflow
target-ppc: KVM: Fix some kernel version edge cases for kvmppc_reset_htab()
pseries: Fix semantics of RTAS int-on, int-off and set-xive functions
pseries: Rework implementation of TCE bypass
pseries: Remove never used flags field from spapr vio devices
pseries: Remove XICS irq type enum type
pseries: Remove C bitfields from xics code
pseries: Small cleanup to H_CEDE implementation
pseries: Fix XICS reset
...
Now that all machines call isa_vga_init() or pci_vga_init(), some unused
code can be removed.
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The CONFIG_SPICE is now tested in vl.c and thus not needed anymore.
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As a bonus it allows new vga card types (including none).
Acked-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Keep the case to prevent some vga card to be selected.
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As a bonus it allows new vga card types (including none).
Acked-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This remove the fallback to std-vga in case, as availability of the
requested vga device is now tested in vl.c, and returns an error message
to the user.
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This function create a ISA VGA device according to the value of
vga_interface_type. It returns a ISADevice (and not a DeviceState).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This function create a PCI VGA device according to the value of
vga_interface_type. It returns a PCIDevice (and not a DeviceState).
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This better explains what is this function about. Adjust all callers.
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This better explains what is this function about. Adjust all callers.
Cc: Alexander Graf <agraf@suse.de>
Cc: Andreas Färber <andreas.faerber@web.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The entries for libhw* are no longer needed in .gitignore.
There is also no longer a difference between common-obj-y and
hw-obj-y, so one of those two macros is sufficient.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It is more readable, and all other code does it like that, too.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
When the DeviceInfo code was removed, the comment describing
qdev_subclass_init() was left in the code by mistake. Remove it.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
It was missing for leon3 and mips_fulong2e.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
This patch cleans up return sentences in the end of void functions.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Implement the century byte in the RTC emulation, and test that it works.
This leads to some annoying compatibility code because we need to treat
a value of 2000 for the base_year property as "use the century byte
properly" (which would be a value of 0).
The century byte will now be always-zero, rather than always-20,
for the MIPS Magnum machine whose base_year is 1980. Commit 42fc73a
(Support epoch of 1980 in RTC emulation for MIPS Magnum, 2009-01-24)
correctly said:
With an epoch of 1980 and a year of 2009, one could argue that [the
century byte] should hold either 0, 1, 19 or 20. NT 3.50 on MIPS
does not read the century byte.
so I picked the simplest and most sensible implementation which is to
return 0 for 1980-2079, 1 for 2080-2179 and so on.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
QEMU's attempt to implement the century byte cover two possible places
for the byte. A common one on modern chipsets is 0x32, but QEMU also
stores the value in 0x37 (apparently for IBM PS/2 compatibility---it's
only been 25 years). To simplify the implementation of the century
byte, store it only at 0x32 but remap transparently 0x37 to 0x32 when
reading and writing from CMOS.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Adjust all uses s/strzcpy/strncpy/ and mark these uses
of strncpy as "ok".
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't use strncpy when the source string is known to fit
in the destination buffer. Use equivalent memcpy.
We could even use strcpy, here, but some static analyzers
warn about that, so don't add new uses.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In all of these cases, the uses of strncpy were unnecessary, since
at each point of use we know that the NUL-terminated source bytes
fit in the destination buffer. Use memcpy in place of strncpy.
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In bt_hci_name_req a failed snprintf could return len larger than
sizeof(params.name), which means the following memset call would
have a "length" value of (size_t)-1, -2, etc... Sounds scary.
But currently, one can deduce that there is no problem:
strlen(slave->lmp_name) is guaranteed to be smaller than
CHANGE_LOCAL_NAME_CP_SIZE, which is the same as sizeof(params.name),
so this cannot happen. Regardless, there is no justification for
using snprintf+memset. Use pstrcpy instead.
Also, in bt_hci_event_complete_read_local_name, use pstrcpy in place
of unwarranted strncpy.
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Actually do what the comment says, using pstrcpy NUL-terminate:
strncpy does not always do that.
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
v9fs_add_dir_node and qemu_v9fs_synth_add_file used strncpy
to form node->name, which requires NUL-termination, but
strncpy does not ensure NUL-termination.
Use pstrcpy, which does.
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Use g_strdup rather than strdup, because the sole caller
(qdev_get_fw_dev_path_helper) assumes it gets non-NULL, and dereferences
it. Besides, in that caller, the allocated buffer is already freed with
g_free, so it's better to allocate with a matching g_strdup.
In one case, (scsi-bus.c) it was trivial, so I replaced an snprintf+
g_strdup combination with an equivalent g_strdup_printf use.
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Those functions return -errno in case of an error.
The old code would typically only detect EPERM (1) errors.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
* sstabellini/xen-2012-10-03:
xen: Set the vram dirty when an error occur.
exec, memory: Call to xen_modified_memory.
exec: Introduce helper to set dirty flags.
xen: Introduce xen_modified_memory.
QMP, Introduce xen-set-global-dirty-log command.
qemu/xen: Add 64 bits big bar support on qemu
xen: Fix, no unplug of pt device by platform device.
* kwolf/for-anthony: (30 commits)
qemu-iotests: add tests for streaming error handling
qemu-iotests: map underscore to dash in QMP argument names
blkdebug: process all set_state rules in the old state
stream: add on-error argument
block: introduce block job error
iostatus: reorganize io error code
iostatus: change is_read to a bool
iostatus: move BlockdevOnError declaration to QAPI
iostatus: rename BlockErrorAction, BlockQMPEventAction
qemu-iotests: add test for pausing a streaming operation
qmp: add block-job-pause and block-job-resume
block: add support for job pause/resume
qmp: add 'busy' member to BlockJobInfo
block: add block_job_query
block: move job APIs to separate files
block: fix documentation of block_job_cancel_sync
qerror/block: introduce QERR_BLOCK_JOB_NOT_ACTIVE
qemu-iotests: add initial tests for live block commit
QAPI: add command for live block commit, 'block-commit'
block: helper function, to find the base image of a chain
...
* qmp/queue/qmp:
block: live snapshot documentation tweaks
input: index_from_key(): drop unused code
qmp: qmp_send_key(): accept key codes in hex
input: qmp_send_key(): simplify
hmp: dump-guest-memory: hardcode protocol argument to "file:"
qmp: dump-guest-memory: don't spin if non-blocking fd would block
qmp: dump-guest-memory: improve schema doc (again)
qapi: convert add_client
monitor: add Error * argument to monitor_get_fd
pci-assign: use monitor_handle_fd_param
qapi: add "unix" to the set of reserved words
qapi: do not protect enum values from namespace pollution
Add qemu-ga-client script
Support settimeout in QEMUMonitorProtocol
Make negotiation optional in QEMUMonitorProtocol
* mst/tags/for_anthony:
virtio-serial-bus: let chardev know the exact number of bytes requested
virtio: Introduce virtqueue_get_avail_bytes()
virtio: use unsigned int for counting bytes in vq
iov: add const annotation
virtio-net: fix used len for tx
virtio: don't mark unaccessed memory as dirty
* kraxel/usb.66:
usb: Fix usb_packet_map() in the presence of IOMMUs
usb-redir: Adjust pkg-config check for usbredirparser .pc file rename (v2)
ehci: Fix interrupt packet MULT handling
xhci: create a memory region for each port
xhci: route string & usb hub support
xhci: tweak limits
compat: turn off msi/msix on xhci for old machine types
add pc-1.3 machine type
Conflicts:
hw/pc_piix.c
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The hassle and compile time overhead of maintaining both 32-bit and 64-bit
capable source isn't worth the tiny performance advantage which is seen on
a minority of configurations. Switch to compiling libhw only once, with
target_phys_addr_t unconditionally typedefed to uint64_t.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When booting our e500 machine, we automatically generate a big TLB entry
in TLB1 that covers all of the code we need to run in there until the guest
can handle its TLB on its own.
However, e500v2 can only handle MAS1.0 sizes. However, we keep our TLB
information in MAS2.0 layout, which means we have twice as many TLB sizes
to choose from. That also means we can run into a situation where we try
to add a TLB size that could not fit into the MAS1.0 size bits.
Fix it by making sure we always have the lower bit set to 0. That way we
are always guaranteed to have MAS1.0 compatible TLB size information.
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR hypercalls should only be invoked from the guest kernel, not guest
user programs, that is, with MSR[PR]=0. Currently we check this in
spapr_hypercall, returning H_PRIVILEGE if MSR[PR]=1.
However, under KVM the state of MSR[PR] is already checked by the host
kernel before passing the hypercall to qemu, making this check redundant.
Worse, however, we don't generally synchronize KVM and qemu state on the
hypercall path, meaning that qemu could incorrectly reject a hypercall
because it has a stale MSR value.
This patch fixes the problem by moving the privilege test exclusively to
the TCG hypercall path.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
CC: qemu-stable@nongnu.org
Signed-off-by: Alexander Graf <agraf@suse.de>
While investigating dtb pad issues, I noticed that initrd_base wasn't taking
loadaddr into account the way dt_base was. This seems wrong.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
An allowance of 5 MiB for BSS is not enough for Linux kernels with certain
debug options enabled (not sure exactly which one caused it, but I'd guess
lockdep). The kernel I ran into this with had a BSS of around 6.4 MB.
Unfortunately, uImage does not give us enough information to determine the
actual BSS size. Increase the allowance to 18 MiB to give us plenty of
room. Eventually this should be more intelligent, possibly packing
initrd+dtb at the end of guest RAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the pseries machine code always attempts to set the size of the
guests's hash page table to 16MB. However, because of the way the POWER
MMU works, a suitable hash page table size should really depend on memory
size. 16MB will be excessive for guests with <1GB and RAM, and may not be
enough for guests with >2GB of RAM (depending on guest page size and
other factors).
The usual given rule of thumb is that the hash table should be 1/64 of
the size of memory, but in fact the Linux guests we are aiming at don't
really need that much. This patch, therefore, changes the hash table
allocation code to aim for 1/128 of the size of RAM (rounding up). When
using KVM, this size may still be adjusted by the host kernel if it is
unable to allocate a suitable (contiguous) table.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the paravirtualized environment provided by PAPR, there is a standard
locking scheme so that hypercalls updating the hash page table from
different guest threads don't corrupt the haah table state. We implement
this HVLOCK bit in out page table hypercalls. However, it is not necessary
in our case, since the hypercalls all run in the qemu environment under the
big qemu lock.
Therefore, this patch removes the locking code. This has the additional
advantage of freeing up a hash PTE bit which will be useful for migration
support.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Report from smatch:
ppc405_uc.c:209 dcr_read_pob(12) error: buffer overflow 'pob->besr' 2 <= 2
ppc405_uc.c:232 dcr_write_pob(12) error: buffer overflow 'pob->besr' 2 <= 2
The old code reads and writes besr[POB0_BESR1 - POB0_BESR0] or besr[2]
which is one too much.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the ibm,int-on and ibm,int-off RTAS functions are implemented as
no-ops. This is because when implemented as specified in PAPR they caused
Linux (which calls both int-on/off and set-xive) to end up with interrupts
masked when they should not be. Since Linux's set-xive calls make the
int-on/off calls redundant, making them nops worked around the problem.
In fact, the problem was caused because there was a subtle bug in set-xive,
PAPR specifies that as well as updating the current priority, it also needs
to update the saved priority used by int-on/off. With this bug fixed the
problem goes away. This patch implements this more correct fix.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
On the pseries machine the IOMMU (aka TCE tables) is always active for all
PCI and VIO devices. Mostly to simplify the SLOF firmware, we implement an
extension which allows the IOMMU to be temporarily disabled for certain
devices.
Currently this is implemented by setting the device's DMAContext pointer to
NULL (thus reverting to qemu's default no-IOMMU DMA behaviour), then
replacing it when bypass mode is disabled.
This approach causes a bunch of complications though. It complexifies the
management of the DMAContext lifetimes, it's problematic for savevm/loadvm,
and it means that while bypass is active we have nowhere to store the
device's LIOBN (Logical IO Bus Number, used to identify DMA address
spaces). At present we regenerate the LIOBN from other address information
but this restricts how we can allocate LIOBNs.
This patch gives up on this approach, replacing it with the much simpler
one of having a 'bypass' boolean flag in the TCE state structure.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The general device state structure for PAPR VIO emulated devices includes a
'flags' field which was never used. This patch removes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the XICS interrupt controller emulation uses a custom enum to
specify whether a given interrupt is level-sensitive or message-triggered.
This enum makes life awkward for saving the state, and isn't particularly
useful since there are only two possibilities. This patch replaces the
enum with a simple bool.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The XICS interrupt controller emulation uses some C bitfield variables in
its internal state structure. This makes like awkward for saving the state
because we don't have easy VMSTATE helpers for bitfields.
This patch removes the bitfields, instead using explicit bit masking in a
single status variable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The H_CEDE hypercall implementation for the pseries machine doesn't trigger
quite the right path in the main cpu exec loop. We should set exit_request
to pop up one extra level and recheck state, and we should set the
exception_index to EXCP_HLT (H_CEDE is roughly equivalent to the hlt
instruction on x86).
In practice, this doesn't really matter except for KVM, and KVM implements
H_CEDE internally so we never hit this code path. But we might as well
get it right, just in case it matters some day.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The XICS interrupt controller used on the pseries machine currently has no
reset handler. We can get away with this under some circumstances, but
it's not correct, and can cause failures if the XICS happens to be in the
wrong state at the time of reset.
This patch adds a hook to properly reset the XICS state.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The emulated PCI host bridge on the pseries machine incorporates an IOMMU
(PAPR TCE table). Currently the mappings in this IOMMU are not cleared
when we reset the system. This patch fixes this bug. To do this it adds
a new reset function to the IOMMU emulation code. The VIO devices already
reset their TCE tables, but they do so by destroying and re-creating their
DMA context. This doesn't work for the PCI host bridge, because the
infrastructure for PCI IOMMUs has already copied/cached the DMA pointer
context into the subordinate PCI device structures.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
When we reset the system, the reset method for VIO bus devices resets
the state of their request queue (if present) as it should. However
it was not resetting the state of their TCE table (DMA translation) if
present. It was also not resetting the state of the per-device signal
mask set with H_VIO_SIGNAL. This patch corrects both bugs, and also
removes some small code duplication in the reset paths.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for then new "reset htab" ioctl which allows qemu
to properly cleanup the MMU hash table when the guest is reset. With
the corresponding kernel support, reset of a guest now works properly.
This also paves the way for indicating a different size hash table
to the kernel and for the kernel to be able to impose limits on
the requested size.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
A number of things need to occur during reset of the PAPR
paravirtualized platform in a specific order. For example, the hash
table needs to be cleared before the CPUs are reset, so that they
initialize their register state correctly, and the CPUs need to have
their main reset called before we set up the entry point state on the
boot cpu. We also need to have the main qdev reset happen before the
creation and installation of the device tree for the new boot, because
we need the state of the devices settled to correctly construct the
device tree.
We currently do the pseries once-per-reset initializations done from a
reset handler. However we can't adequately control when this handler
is called during the reset - in particular we can't guarantee it
happens after all the qdev resets (since qdevs might be registered
after the machine init function has executed).
This patch uses the new QEMUMachine reset method to to fix this
problem, ensuring the various order dependent reset steps happen in
the correct order.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current pseries machine init function iterates over the CPUs at several
points, doing various bits of initialization. This is messy; these can
and should be merged into a single iteration doing all the necessary per
cpu initialization. Worse, some of these initializations were setting up
state which should be set on every reset, not just at machine init time.
A few of the initializations simply weren't necessary at all.
This patch, therefore, moves those things that need to be to the
per-cpu reset handler, and combines the remainder into two loops over
the cpus (which also creates them). The second loop is for setting up
hash table information, and will be removed in a subsequent patch also
making other fixes to the hash table setup.
This exposes a bug in our start-cpu RTAS routine (called by the guest to
start up CPUs other than CPU0) under kvm. Previously, this function did
not make a call to ensure that it's changes to the new cpu's state were
pushed into KVM in-kernel state. We sort-of got away with this because
some of the initializations had already placed the secondary CPUs into the
right starting state for the sorts of Linux guests we've been running.
Nonetheless the start-cpu RTAS call's behaviour was not correct and could
easily have been broken by guest changes. This patch also fixes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This function is to be used during live migration. Every write access to the
guest memory should call this funcion so the Xen tools knows which pages are
dirty.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Currently it is assumed PCI device BAR access < 4G memory. If there is such a
device whose BAR size is larger than 4G, it must access > 4G memory address.
This patch enable the 64bits big BAR support on qemu.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The Xen platform device will unplug any NICs if requested by the guest (PVonHVM)
including a NIC that would have been passthrough. This patch makes sure that a
passthrough device will not be unplug.
Reported-by: "Zhang, Yang Z" <yang.z.zhang@intel.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
We cannot cast directly from pointer to uint64.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alex Barcelo <abarcelo@ac.upc.edu>
Reported-by: Alex Barcelo <abarcelo@ac.upc.edu>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Enabled for all softmmu guests supporting PCI on Linux hosts. Note
that currently only x86 hosts have the kernel side VFIO IOMMU support
for this. PPC (g3beige) is the only non-x86 guest known to work.
ARM (veratile) hangs in firmware, others untested.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds the core of the QEMU VFIO-based PCI device assignment driver.
To make use of this driver, enable CONFIG_VFIO, CONFIG_VFIO_IOMMU_TYPE1,
and CONFIG_VFIO_PCI in your host Linux kernel config. Load the vfio-pci
module. To assign device 0000:05:00.0 to a guest, do the following:
for dev in $(ls /sys/bus/pci/devices/0000:05:00.0/iommu_group/devices); do
vendor=$(cat /sys/bus/pci/devices/$dev/vendor)
device=$(cat /sys/bus/pci/devices/$dev/device)
if [ -e /sys/bus/pci/devices/$dev/driver ]; then
echo $dev > /sys/bus/pci/devices/$dev/driver/unbind
fi
echo $vendor $device > /sys/bus/pci/drivers/vfio-pci/new_id
done
See Documentation/vfio.txt in the Linux kernel tree for further
description of IOMMU groups and VFIO.
Then launch qemu including the option:
-device vfio-pci,host=0000:05:00.0
Legacy PCI interrupts (INTx) currently makes use of a kludge where we
trap BAR accesses and assume the access is in response to an interrupt,
therefore de-asserting and unmasking the interrupt. It's not quite as
targetted as using the EOI for this, but it's self contained and seems
to work across all architectures. The side-effect is a significant
performance slow-down for device in INTx mode. Some devices, like
graphics cards, don't really use their interrupt, so this can be turned
off with the x-intx=off option, which disables INTx alltogether. This
should be considered an experimental option until we refine this code.
Both MSI and MSI-X are supported and avoid these issues.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move the common part of IDE/SCSI/virtio error handling to the block
layer. The new function bdrv_error_action subsumes all three of
bdrv_emit_qmp_error_event, vm_stop, bdrv_iostatus_set_err.
The same scheme will be used for errors in block jobs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Do this while we are touching this part of the code, before introducing
more uses of "int is_read".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This will let block-stream reuse the enum. Places that used the enums
are renamed accordingly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to remove knowledge of BLOCK_ERR_STOP_ENOSPC from drivers;
drivers should only be told whether to stop/report/ignore the error.
On the other hand, we want to keep using the nicer BlockErrorAction
name in the drivers. So rename the enums, while leaving aside the
names of the enum values for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using the virtqueue_avail_bytes() function had an unnecessarily
crippling effect on the number of bytes needed by the guest as reported
to the chardev layer in the can_read() callback.
Using the new virtqueue_get_avail_bytes() function will let us advertise
the exact number of bytes we can send to the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current virtqueue_avail_bytes() is oddly named, and checks if a
particular number of bytes are available in a vq. A better API is to
fetch the number of bytes available in the vq, and let the caller do
what's interesting with the numbers.
Introduce virtqueue_get_avail_bytes(), which returns the number of bytes
for buffers marked for both, in as well as out. virtqueue_avail_bytes()
is made a wrapper over this new function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtqueue_avail_bytes() function counts bytes in an int. Use an
unsigned int instead.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
offset of accessed buffer is calculated using iov_length, so it
can exceed accessed len. If that happens
math in len - offset wraps around, and size becomes wrong.
As real value is 0, so this is harmless but unnecessary.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds modelling of the two NOR flash banks found on the
Versatile Express motherboard. Tested with U-Boot running on an emulated
Versatile Express, with either A9 or A15 CoreTile.
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the A series memory map (implemented in the Cortex A15 CoreTile), the
first NOR flash bank (flash 0) is mapped to address 0x08000000, while
address 0x00000000 can be configured as alias to either the first or the
second flash bank. This patch fixes the definition of flash 0 address,
and for simplicity removes the alias definition.
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When setting up the NVIC memory regions the memory range
0x100..0xcff is aliased to an IO memory region that belongs
to the ARM GIC. This aliased region should be added to the
NVIC memory container, but the actual GIC IO memory region
was being added instead. This mixup was causing the wrong
IO memory access functions to be called when accessing parts
of the NVIC memory.
Signed-off-by: Meador Inge <meadori@codesourcery.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reading VECTADDR was causing us to set the current priority to
the wrong value, the most obvious effect of which was that we
would return the vector for the wrong interrupt as the result
of the read.
Signed-off-by: Brendan Fennell <bfennell@skynet.ie>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no need to open-code the choice between a file descriptor
number or a named one. Just use monitor_handle_fd_param, which
also takes care of printing the error message.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
With the IOMMU infrastructure introduced before 1.2, we need to use
dma_memory_map() to obtain a qemu pointer to memory from an IO bus address.
However, dma_memory_map() alters the given length to reflect the length
over which the used DMA translation is valid - which could be either more
or less than the requested length.
usb_packet_map() does not correctly handle these cases, simply failing if
dma_memory_map() alters the requested length. If dma_memory_map()
increased the length, we just need to use the requested length for the
qemu_iovec_add(). However, if it decreased the length, it means that a
single DMA translation is not valid for the whole sglist element, and so
we need to loop, splitting it up into multiple iovec entries for each
piece with a DMA translation (in practice >2 pieces is unlikely).
This patch implements the correct behaviour
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There are several issues with our handling of the MULT epcap field
of interrupt qhs, which this patch fixes.
1) When we don't execute a transaction because of the transaction counter
being 0, p->async stays EHCI_ASYNC_NONE, and the next time we process the
same qtd we hit an assert in ehci_state_fetchqtd because of this. Even though
I believe that this is caused by 3 below, this patch still removes the assert,
as that can still happen without 3, when multiple packets are queued for the
same interrupt ep.
2) We only *check* the transaction counter from ehci_state_execute, any
packets queued up by fill_queue bypass this check. This is fixed by not calling
fill_queue for interrupt packets.
3) Some versions of Windows set the MULT field of the qh to 0, which is a
clear violation of the EHCI spec, but still they do it. This means that we
will never execute a qtd for these, making interrupt ep-s on USB-2 devices
not work, and after recent changes, triggering 1).
So far we've stored the transaction counter in our copy of the mult field,
but with this beginnig at 0 already when dealing with these version of windows
this won't work. So this patch adds a transact_ctr field to our qh struct,
and sets this to the MULT field value on fetchqh. When the MULT field value
is 0, we set it to 4. Assuming that windows gets way with setting it to 0,
by the actual hardware going horizontal on a 1 -> 0 transition, which will
give it 4 transactions (MULT goes from 0 - 3).
Note that we cannot stop on detecting the 1 -> 0 transition, as our decrement
of the transaction counter, and checking for it are done in 2 different places.
Reported-by: Shawn Starr <shawn.starr@rogers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Set maxports to 15. This is what the usb3 route string can handle.
Set maxslots to 64. This is more than the number of root ports we
can have, but with additional hubs you can end up with more devices.
Set maxintrs (aka msi vectors) to 16. Should be enougth, especially
considering that vectors are a limited ressource. Linux guests use
only three at the moment.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Added an option to let qemu transfer a configuration file to bios,
"etc/boot-fail-wait", which could be specified by command
-boot reboot-timeout=T
T have a max value of 0xffff, unit is ms.
With this option, guest will wait for a given time if not find
bootabled device, then reboot. If reboot-timeout is '-1', guest
will not reboot, qemu passes '-1' to bios by default.
This feature need the new seabios's support.
Seabios pulls the value from the fwcfg "file" interface, this
interface is used because SeaBIOS needs a reliable way of
obtaining a name, value size, and value. It in no way requires
that there be a real file on the user's host machine.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a "use64" property which will make the ivshmem driver
register a 64bit memory bar when set, so you have something to play with
when testing 64bit pci bits. It also allows to have quite big shared
memory regions, like this:
[root@fedora ~]# lspci -vs1:1
01:01.0 RAM memory: Red Hat, Inc Device 1110
Subsystem: Red Hat, Inc Device 1100
Physical Slot: 1-1
Flags: fast devsel
Memory at fd400000 (32-bit, non-prefetchable) [disabled] [size=256]
Memory at 8040000000 (64-bit, prefetchable) [size=1G]
[ v5: rebase, update compat property for post-1.2 merge ]
[ v4: rebase & adapt to latest master again ]
[ v3: rebase & adapt to latest master ]
[ v2: default to on as suggested by avi,
turn off for pc-$old using compat property ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Cam Macdonell <cam@cs.ualberta.ca>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In addition, there is no need to allocate an extra irq just for
rising SCI in irq handler. Just rise SCI right from notifier
handler instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* stefanha/trivial-patches:
w32: Always use standard instead of native format strings
net/socket: Fix compiler warning (regression for MinGW)
linux-user: Remove redundant null check and replace free by g_free
qemu-timer: simplify qemu_run_timers
TextConsole: saturate escape parameter in TTY_STATE_CSI
curses: don't initialize curses when qemu is daemonized
dtrace backend: add function to reserved words
pflash_cfi01: Fix warning caused by unreachable code
ioh3420: Remove unreachable code
lm4549: Fix buffer overflow
cadence_uart: Fix buffer overflow
qemu-sockets: Fix potential memory leak
qemu-ga: Remove unreachable code after g_error
target-i386: Allow tsc-frequency to be larger then 2.147G
* bonzini/scsi-next:
SCSI: Standard INQUIRY data should report HiSup flag as set.
scsi-disk: use scsi_data_cdb_length
scsi: introduce scsi_cdb_length and scsi_data_cdb_length
scsi-disk: fix check for out-of-range LBA
scsi-disk: introduce check_lba_range
iSCSI: We dont need to explicitely call qemu_notify_event() any more
iSCSI: We need to support SG_IO also from iscsi_ioctl()
Report from smatch:
hw/pflash_cfi01.c:431 pflash_write(180) info: ignoring unreachable code.
Instead of removing the return statement after the switch statement,
the patch replaces the return statements in the switch statement by
break statements. Other switch statements in the same code do it also
like that.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Report from smatch:
hw/ioh3420.c:128 ioh3420_initfn(35) info: ignoring unreachable code.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Report from smatch:
lm4549.c:234 lm4549_write_samples(14) error:
buffer overflow 's->buffer' 1024 <= 1024
There must be enough space to add two entries starting with index
s->buffer_level, therefore the old check was wrong.
[Peter Maydell <peter.maydell@linaro.org> clarifies the nature of the
analyser warning:
I don't object to making the change to placate the analyser,
but I don't think this is actually a buffer overrun. We always
add and remove samples from the buffer two at a time, so it's
not possible to get here with s->buffer_level == BUFFER_SIZE-1
(which is the only case where the old and new conditions
give different answers).]
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Report from smatch:
hw/cadence_uart.c:413 uart_read(13) error: buffer overflow 's->r' 18 <= 18
This fixes read access to s->r[R_MAX] which is behind the limits of s->r.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
* 'usb.65' of git://git.kraxel.org/qemu:
uhci: Don't queue up packets after one with the SPD flag set
usb-redir: Revert usb-redir part of commit 93bfef4c
usb-redir: Add chardev open / close debug logging
usb-redir: Add support for migration
usb-redir: Store max_packet_size in endp_data
usb-redir: Add an already_in_flight packet-id queue
usb-redir: Change cancelled packet code into a generic packet-id queue
ehci: Walk async schedule before and after migration
ehci: Don't set seen to 0 when removing unseen queue-heads
configure: usbredir fixes
ehci: Don't process too much frames in 1 timer tick (v2)
ehci: Fix interrupts stopping when Interrupt Threshold Control is 8
ehci: switch to new-style memory ops
usb-host: allow emulated (non-async) control requests without USBPacket
QEMU as far as I know only reports LUN numbers using the modes that
are described in SAM4.
As such, since all LUN numbers generated by the SCSI emulation in QEMU
follow SAM4, we should set the HiSup bit in the standard INQUIRY data
to indicate such.
From SAM4:
4.6.3 LUNs overview
All LUN formats described in this standard are hierarchical in
structure even when only a single level in that hierarchy is used.
The HISUP bit shall be set to one in the standard INQUIRY data
(see SPC-4) when any LUN format described in this standard is used.
Non-hierarchical formats are outside the scope of this standard.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
This fix is needed to correctly handle 0-block read and writes.
Without it, a 0-block access at LBA 0 would underflow.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the private reimplementation of ctz32() from pflash_cfi0[12]
in favour of using the standard version from host-utils.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
pflash_cfi01 announces a version number of 1.1, which implies
"Protection Register Information" and "Burst Read information"
sections, which are not provided.
Decrease the version number to 1.0 so that only the "Protection
Register Information" section is needed.
Set the number of protection fields (0x3f) to 0x01, as 0x00 means 256
protections field, which makes the CFI table bigger than the current
implementation, causing some kernels to fail to read it.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There was a missing include of qemu-log and a variable name in a printf was out
of date.
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Assert that the ethernet and dma controller are sucessfully linked to their
peers.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
The "frequency" qdev prop matches the "clock-frequency" property in Xilinx EDK.
Renamed "frequency" -> "clock-frequency" accordingly.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
* kwolf/for-anthony:
block: Don't forget to delete temporary file
Don't require encryption password for 'qemu-img info' command
qemu-img: Add json output option to the info command.
qapi: Add SnapshotInfo and ImageInfo.
ahci: properly reset PxCMD on HBA reset
block: fix block tray status
vdi: Fix warning from clang
block/curl: Fix wrong free statement
ide: Fix error messages from static code analysis (no real error)
ATAPI: STARTSTOPUNIT only eject/load media if powercondition is 0
sheepdog: fix savevm and loadvm
* stefanha/trivial-patches:
configure: fix seccomp check
arch_init.c: add missing '%' symbols before PRIu64 in debug printfs
kvm: Fix warning from static code analysis
qapi: Fix enumeration typo error
console: Clean up bytes per pixel calculation
Fix copy&paste typos in documentation comments
linux-user: Remove #if 0'd cpu_get_real_ticks() definition
ui: Fix spelling in comment (ressource -> resource)
Spelling fixes in comments and macro names (ressource -> resource)
Fix spelling (licenced -> licensed) in GPL
Spelling fixes in comments and documentation
srp: Don't use QEMU_PACKED for single elements of a structured type
* stefanha/net:
net: EAGAIN handling for net/socket.c TCP
net: EAGAIN handling for net/socket.c UDP
net: asynchronous send/receive infrastructure for net/socket.c
net: broadcast hub packets if at least one port can receive
net: fix usbnet_receive() packet drops
net: clean up usbnet_receive()
net: add -netdev options to man page
net: do not report queued packets as sent
net: add receive_disabled logic to iov delivery path
eepro100: Fix network hang when rx buffers run out
xen: flush queue when getting an event
e1000: flush queue whenever can_receive can go from false to true
net: notify iothread after flushing queue
* qemu-kvm/uq/master:
kvm: Rename irqchip_inject_ioctl to irq_set_ioctl
kvm: Stop flushing coalesced MMIO on vmexit
VGA: Flush coalesced MMIO on related MMIO/PIO accesses
memory: Flush coalesced MMIO on mapping and state changes
memory: Fold memory_region_update_topology into memory_region_transaction_commit
memory: Use transaction_begin/commit also for single-step operations
memory: Flush coalesced MMIO on selected region access
kvm-all.c: Move init of irqchip_inject_ioctl out of kvm_irqchip_create()
update-linux-headers.sh: Don't hard code list of architectures
We have debugcon these days to listen on those ports that receive debug
messages. Also drop the others that have no effect anymore.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Now that CONFIG_TCG_PASS_AREG0 is enabled for all targets,
remove dead code and support for !CONFIG_TCG_PASS_AREG0 case.
Remove dyngen-exec.h and all references to it. Although included by
hw/spapr_hcall.c, it does not seem to use it.
Remove unused HELPER_CFLAGS.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The USB network interface has a single buffer which the guest reads
from. This patch prevents multiple calls to usbnet_receive() from
clobbering the input buffer. Instead we queue packets until buffer
space becomes available again.
This is inspired by virtio-net and e1000 rxbuf handling.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The USB network interface has two code paths depending on whether or not
RNDIS mode is enabled. Refactor usbnet_receive() so that there is a
common path throughout the function instead of duplicating everything
across if (is_rndis(s)) ... else ... code paths.
Clean up coding style and 80 character line wrap along the way.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This is reported by QA. When installing os with pxe, after the initial
kernel and initrd are loaded, the procedure tries to copy files from install
server to local harddisk, the network becomes stall because of running out of
receive descriptor.
[Whitespace fixes and removed qemu_notify_event() because Paolo's
earlier net patches have moved it into qemu_flush_queued_packets().
Additional info:
I can reproduce the network hang with a tap device doing a iPXE HTTP
boot as follows:
$ qemu -enable-kvm -m 1024 \
-netdev tap,id=netdev0,script=no,downscript=no \
-device i82559er,netdev=netdev0,romfile=80861209.rom \
-drive if=virtio,cache=none,file=test.img
iPXE> ifopen net0
iPXE> config # set static network configuration
iPXE> kernel http://mirror.bytemark.co.uk/fedora/linux/releases/17/Fedora/x86_64/os/images/pxeboot/vmlinuz
I needed a vanilla iPXE ROM to get to the iPXE prompt. I think the boot
prompt has been disabled in the ROMs that ship with QEMU to reduce boot
time.
During the vmlinuz HTTP download there is a network hang. hw/eepro100.c
has reached the end of the rx descriptor list. When the iPXE driver
replenishes the rx descriptor list we don't kick the QEMU net subsystem
and event loop, thereby leaving the tap netdev without its file
descriptor in select(2).
Stefan Hajnoczi <stefanha@gmail.com>]
Signed-off-by: Bo Yang <boyang@suse.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
xen does not have a register that, when written, will cause can_receive
to go from false to true. However, flushing the queue can be attempted
whenever the front-end raises its side of the Xen event channel. There
is a single event channel for tx and rx.
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
When the guests replenish the receive ring buffer, the network device
should flush its queue of pending packets. This is done with
qemu_flush_queued_packets.
e1000's can_receive can go from false to true when RCTL or RDT are
modified.
Reported-by: Luigi Rizzo <rizzo@iet.unipi.it>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Jan Kiszka <jan.kiszka@siemens.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
virtio-net has code to flush the queue and notify the iothread
whenever new receive buffers are added by the guest. That is
fine, and indeed we need to do the same in all other drivers.
However, notifying the iothread should be work for the network
subsystem. And since we are at it we can add a little smartness:
if some of the queued packets already could not be delivered,
there is no need to notify the iothread.
Reported-by: Luigi Rizzo <rizzo@iet.unipi.it>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Jan Kiszka <jan.kiszka@siemens.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
