Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180227143852.11175-3-alex.bennee@linaro.org
[PMM: postpone actually enabling feature until end of the
patch series]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows us to explicitly pass float16 to helpers rather than
assuming uint32_t and dealing with the result. Of course they will be
passed in i32 sized registers by default.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180227143852.11175-2-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the SiI9022 (and implicitly EDID I2C) device to the ARM
Versatile Express machine, and selects the two I2C devices necessary
in the arm-softmmu.mak configuration so everything will build
smoothly.
I am implementing proper handling of the graphics in the Linux
kernel and adding proper emulation of SiI9022 and EDID makes the
driver probe as nicely as before, retrieving the resolutions
supported by the "QEMU monitor" and overall just working nice.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-6-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for emulating the Silicon Image SII9022 DVI/HDMI
bridge. It's not very clever right now, it just acknowledges
the switch into DDC I2C mode and back. Combining this with the
existing DDC I2C emulation gives the right behavior on the Versatile
Express emulation passing through the QEMU EDID to the emulated
platform.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-5-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: explictly reset ddc_req/ddc_skip_finish/ddc]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The tx function of the DDC I2C slave emulation was returning 1
on all writes resulting in NACK in the I2C bus. Changing it to
0 makes the DDC I2C work fine with bit-banged I2C such as the
versatile I2C.
I guess it was not affecting whatever I2C controller this was
used with until now, but with the Versatile I2C it surely
does not work.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-4-linus.walleij@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some devices need access to it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-3-linus.walleij@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use 8 dummy cycles (4 dummy bytes) with the QIOR/QIOR4 commands in legacy mode
for matching what is expected by Micron (Numonyx) flashes (the default target
flash type of the QSPI).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Assert only the lower cs on bus 0 and upper cs on bus 1 when both buses and
chip selects are enabled (e.g reading/writing with stripe).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure that the post write hook is called during reset. This allows us
to rely on the post write functions instead of having to call them from
the reset() function.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: d131e24b911653a945e46ca2d8f90f572469e1dd.1517856214.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>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=a866
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/linux-user-for-2.12-pull-request' into staging
# gpg: Signature made Sun 25 Feb 2018 17:54:21 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/linux-user-for-2.12-pull-request:
linux-user: MIPS set cpu to r6 CPU if binary is R6
linux-user, m68k: select CPU according to ELF header values
linux-user: introduce functions to detect CPU type
linux-user: Move CPU type name selection to a function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to a kernel bug we can never increase the size of capability
set 1, so introduce a new capability set in parallel, old userspace
will continue to use the old set, new userspace will start using
the new one when it detects a fixed kernel.
v2: don't use a define from virglrenderer, just probe it.
v3: fix compilation when virglrenderer disabled
v4: fix style warning, just use ?: op instead.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Message-id: 20180223023814.24459-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch implements a dummy ObjectInfo structure so that
it's easy to typecast the incoming data. If the metadata is
valid, write_pending is set. Also, the incoming filename
is utf-16, so, instead of depending on external libraries, just
implement a simple function to get the filename
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-6-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Allow write operations on behalf of the initiator. The
precursor to write is the sending of the write metadata
that consists of the ObjectInfo dataset. This patch introduces
a flag that is set when the responder is ready to receive
write data based on a previous SendObjectInfo operation by
the initiator (The SendObjectInfo implementation is in a
later patch)
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-5-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Write of existing objects by the initiator is acheived by
making a temporary buffer with the new changes, deleting the
old file and then writing a new file with the same name.
Also, add a "readonly" property which needs to be set to false
for deletion to work.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix a possible null dereference when deleting a folder and
its contents. An ignored event might be received for its contents
after the parent folder is deleted which will return a null object.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The response to a SendObjectInfo consists of the storageid,
parent obejct handle and the handle reserved for the new
incoming object
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
So here we need to detect the version of binaries and set
cpu_model for it.
Signed-off-by: YunQiang Su <syq@debian.org>
[lv: original patch modified to move code into cpu_get_model()]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180220173307.25125-5-laurent@vivier.eu>
M680x0 doesn't support the same set of instructions
as ColdFire, so we can't use "any" CPU type to execute
m68020 instructions.
We select CPU type ("m68040" or "any" for ColdFire)
according to the ELF header. If we can't, we
use by default the value used until now: "any".
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180220173307.25125-4-laurent@vivier.eu>
Add a function to return ELF e_flags and use it
to select the CPU model.
Signed-off-by: YunQiang Su <syq@debian.org>
[lv: split the patch and some cleanup in get_elf_eflags()]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180220173307.25125-3-laurent@vivier.eu>
Instead of a sequence of "#if ... #endif" move the
selection to a function in linux-user/*/target_elf.h
We can't add them in linux-user/*/target_cpu.h
because we will need to include "elf.h" to
use ELF flags with eflags, and including
"elf.h" in "target_cpu.h" introduces some
conflicts in elfload.c
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180220173307.25125-2-laurent@vivier.eu>
Add myself as an OpenBSD maintainer and add OpenBSD as maintained.
Signed-off-by: Brad Smith <brad@comstyle.com>
Reviewed-by: Kamil Rytarowski <n54@gmx.com>
Message-id: 20180216164620.GA53727@humpty.home.comstyle.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To be used to decode ARM SVE, but could be used for any fixed-width ISA.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Fix bad register definitions for VMIDR and VMPIDR (which caused
assertions for 64-bit guest CPUs with EL2 on big-endian hosts)
* hw/char/stm32f2xx_usart: fix TXE/TC bit handling
* Fix ast2500 protection register emulation
* Lots of SD card emulation cleanups and bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EtGK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180222' into staging
* New "raspi3" machine emulating RaspberryPi 3
* Fix bad register definitions for VMIDR and VMPIDR (which caused
assertions for 64-bit guest CPUs with EL2 on big-endian hosts)
* hw/char/stm32f2xx_usart: fix TXE/TC bit handling
* Fix ast2500 protection register emulation
* Lots of SD card emulation cleanups and bugfixes
# gpg: Signature made Thu 22 Feb 2018 15:18:53 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180222: (32 commits)
sdcard: simplify SD_SEND_OP_COND (ACMD41)
sdcard: simplify SEND_IF_COND (CMD8)
sdcard: warn if host uses an incorrect address for APP CMD (CMD55)
sdcard: check the card is in correct state for APP CMD (CMD55)
sdcard: handles more commands in SPI mode
sdcard: use a more descriptive label 'unimplemented_spi_cmd'
sdcard: handle the Security Specification commands
sdcard: handle CMD54 (SDIO)
sdcard: use the registerfields API for the CARD_STATUS register masks
sdcard: use the correct masked OCR in the R3 reply
sdcard: simplify using the ldst API
sdcard: remove commands from unsupported old MMC specification
sdcard: clean the SCR register and add few comments
sdcard: fix the 'maximum data transfer rate' to 25MHz
sdcard: update the CSD CRC register regardless the CSD structure version
sdcard: Don't always set the high capacity bit
sdcard: use the registerfields API to access the OCR register
sdcard: use G_BYTE from cutils
sdcard: define SDMMC_CMD_MAX instead of using the magic '64'
sdcard: add more trace events
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-13-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
returning sd_illegal, since they are not implemented.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-11-f4bug@amsat.org
[PMM: tweak multiline comment format]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux uses it to poll the bus before polling for a card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-9-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
use the registerfields API to access the OCR register
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
the code is easier to review/refactor.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device does not model MMCA Specification previous to v4.2
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To comply with Spec v1.10 (and 2.00, 3.01):
. TRAN_SPEED
for current SD Memory Cards that field must be always 0_0110_010b (032h) which is
equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-4-f4bug@amsat.org
[PMM: fixed comment indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't set the high capacity bit by default as it will be set if required
in the sd_set_csd() function.
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
and Peter Ogden <ogden@xilinx.com> from qemu/xilinx tag xilinx-v2015.4]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
code is now easier to read.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180215220540.6556-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
