In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add MAX31785 fan controllers in machines so that the Linux driver
populates the sysfs interface.
Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9.
Witherspoon has one at 0x52 on bus 3.
Rainier has one at 0x52 on bus 7.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Move the code from hw/arm/virt.c that is supposed
to handle v7 into the one function.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reported-by: He Zhe <zhe.he@windriver.com>
Message-id: 20220619001541.131672-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate the I2C buses in AST1030 model and create two slave device
for ast1030-evb.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg : - adapted to current AST1030 upstream models
- changed AST2600 to AST1030 in comment
- fixed typo in commit log ]
Message-Id: <20220324100439.478317-3-troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The board has no such device. It might have been useful for some tests
in the past, it's not anymore and the same can be achieved on the
command line.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Various loader functions return an int which limits images to 2GB which
is fine for things like a BIOS/kernel image, but if we want to be able
to load memory images or large ramdisks then any file over 2GB would
silently fail to load.
Cc: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211111141141.3295094-2-jamie@nuviainc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When the display port has been initially implemented the device
driver wasn't using interrupts. Now that the display port driver
waits for vblank interrupt it has been noticed that the irq mapping
is wrong. So use the value from the linux device tree and the
ultrascale+ reference manual.
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220601172353.3220232-5-fkonrad@xilinx.com
[PMM: refold lines in commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add EEPROM and LM75 temperature sensor according to hardware schematic
Signed-off-by: Howard Chiu <howard_chiu@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 integrates one set of Parallel GPIO Controller
with maximum 151 control pins, which are 21 groups
(A~U, exclude pin: M6 M7 Q5 Q6 Q7 R0 R1 R4 R5 R6 R7 S0 S3 S4
S5 S6 S7 ) and the group T and U are input only.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220525053444.27228-3-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Background:
AspeedMachineClass.uart_default specifies the serial console UART, which
usually corresponds to the "stdout-path" in the device tree.
The default value is UART5, since most boards use UART5 for this:
amc->uart_default = ASPEED_DEV_UART5;
Users can override AspeedMachineClass.uart_default in their board's machine
class init to specify something besides UART5. For example, for fuji-bmc:
amc->uart_default = ASPEED_DEV_UART1;
We only connect this one UART, of the 5 UART's on the AST2400 and AST2500
and the 13 UART's on the AST2600 and AST1030, to a serial device that QEMU
users can use. None of the other UART's are initialized, and the only way
to override this attribute is by creating a specialized board definition,
requiring QEMU source code changes and rebuilding.
The result of this is that if you want to get serial console output on a
board that uses UART3, you need to add a board definition. This was
encountered by Zev in OpenBMC. [1]
Changes:
This commit initializes all of the UART's present on each Aspeed chip with
serial devices and allows the QEMU user to connect as many or few as they
like to serial devices. For example, you can still run QEMU and just connect
stdout to the machine's default UART, without specifying any additional
serial devices:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
However, if you don't want to add a special machine definition, you can now
manually configure UART1 to connect to stdout and get serial console output,
even if the machine's default is UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
In the example above, the first "-serial null" argument is connected to
UART5, and "-serial mon:stdio" is connected to UART1.
Another example: you can get serial console output from Wedge100, which uses
UART3, by reusing the palmetto AST2400 machine and rewiring the serial
device arguments:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
There is a slight change in behavior introduced with this change: now, each
UART's memory-mapped IO region will have a serial device model connected to
it. Previously, all reads and writes to those regions would be ineffective
and return zero values, but now some values will be nonzero, even when the
user doesn't connect a serial device backend (like a socket, file, etc). For
example, the line status register might indicate that the transmit buffer is
empty now, whereas previously it might have always indicated it was full.
[1] https://lore.kernel.org/openbmc/YnzGnWjkYdMUUNyM@hatter.bewilderbeest.net/
[2] https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
[3] https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-6-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST1030 machine initialization was not respecting the Aspeed SoC
property "uart-default", which specifies which UART should be connected to
the first serial device, it was just always connecting UART5. This doesn't
change any behavior, because the default value for "uart-default" is UART5,
but it makes it possible to override this in new machine definitions using
the AST1030.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500,
AST2600, and AST1030.
This also includes the new UART interfaces added in the AST2600 and AST1030
from UART6 to UART13. The addresses and interrupt numbers for these two
later chips are identical.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and make routine aspeed_soc_get_irq() common to all SoCs. This will be
useful to share code.
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516055620.2380197-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the 'fby35-bmc' machine type based on the kernel DTS[1] and userspace
i2c setup scripts[2]. Undefined values are inherited from the AST2600-EVB.
Reference images can be found in Facebook OpenBMC Github Release assets
as "fby35.mtd". [3]
You can boot the reference images as follows (fby35 uses dual-flash):
qemu-system-arm -machine fby35-bmc \
-drive file=fby35.mtd,format=raw,if=mtd \
-drive file=fby35.mtd,format=raw,if=mtd \
-nographic
[1] 412d505325/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
[2] e2294ff5d3/meta-facebook/meta-fby35/recipes-fby35/plat-utils/files/setup-dev.sh
[3] https://github.com/facebook/openbmc/releases
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220503225925.1798324-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We had a few CPTR_* bits defined, but missed quite a few.
Complete all of the fields up to ARMv9.2.
Use FIELD_EX64 instead of manual extract32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220517054850.177016-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The traditional ptimer behaviour includes a collection of weird edge
case behaviours. In 2016 we improved the ptimer implementation to
fix these and generally make the behaviour more flexible, with
ptimers opting in to the new behaviour by passing an appropriate set
of policy flags to ptimer_init(). For backwards-compatibility, we
defined PTIMER_POLICY_DEFAULT (which sets no flags) to give the old
weird behaviour.
This turns out to be a poor choice of name, because people writing
new devices which use ptimers are misled into thinking that the
default is probably a sensible choice of flags, when in fact it is
almost always not what you want. Rename PTIMER_POLICY_DEFAULT to
PTIMER_POLICY_LEGACY and beef up the comment to more clearly say that
new devices should not be using it.
The code-change part of this commit was produced by
sed -i -e 's/PTIMER_POLICY_DEFAULT/PTIMER_POLICY_LEGACY/g' $(git grep -l PTIMER_POLICY_DEFAULT)
with the exception of a test name string change in
tests/unit/ptimer-test.c which was added manually.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220516103058.162280-1-peter.maydell@linaro.org
The virt board generates a gpio-keys node in the dtb, but it
incorrectly gives this node #size-cells and #address-cells
properties. If you dump the dtb with 'machine dumpdtb=file.dtb'
and run it through dtc, dtc will warn about this:
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the bogus properties.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-3-peter.maydell@linaro.org
In the virt board with secure=on we put two nodes in the dtb
for flash devices: one for the secure-only flash, and one
for the non-secure flash. We get the reg properties for these
correct, but in the DT node name, which by convention includes
the base address of devices, we used the wrong address. Fix it.
Spotted by dtc, which will complain
Warning (unique_unit_address): /flash@0: duplicate unit-address (also used in node /secflash@0)
if you dump the dtb from QEMU with -machine dumpdtb=file.dtb
and then decompile it with dtc.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-2-peter.maydell@linaro.org
This adds code to instantiate the slightly extended ACPI root port
description in DSDT as per the CXL 2.0 specification.
Basically a cut and paste job from the i386/pc code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-30-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As part of converting -boot to a property with a QAPI type, define
the struct and use it throughout QEMU to access boot configuration.
machine_boot_parse takes care of doing the QemuOpts->QAPI conversion by
hand, for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When CPU-to-NUMA association isn't explicitly provided by users,
the default one is given by mc->get_default_cpu_node_id(). However,
the CPU topology isn't fully considered in the default association
and this causes CPU topology broken warnings on booting Linux guest.
For example, the following warning messages are observed when the
Linux guest is booted with the following command lines.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host \
-cpu host \
-smp 6,sockets=2,cores=3,threads=1 \
-m 1024M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=128M \
-object memory-backend-ram,id=mem1,size=128M \
-object memory-backend-ram,id=mem2,size=128M \
-object memory-backend-ram,id=mem3,size=128M \
-object memory-backend-ram,id=mem4,size=128M \
-object memory-backend-ram,id=mem4,size=384M \
-numa node,nodeid=0,memdev=mem0 \
-numa node,nodeid=1,memdev=mem1 \
-numa node,nodeid=2,memdev=mem2 \
-numa node,nodeid=3,memdev=mem3 \
-numa node,nodeid=4,memdev=mem4 \
-numa node,nodeid=5,memdev=mem5
:
alternatives: patching kernel code
BUG: arch topology borken
the CLS domain not a subset of the MC domain
<the above error log repeats>
BUG: arch topology borken
the DIE domain not a subset of the NODE domain
With current implementation of mc->get_default_cpu_node_id(),
CPU#0 to CPU#5 are associated with NODE#0 to NODE#5 separately.
That's incorrect because CPU#0/1/2 should be associated with same
NUMA node because they're seated in same socket.
This fixes the issue by considering the socket ID when the default
CPU-to-NUMA association is provided in virt_possible_cpu_arch_ids().
With this applied, no more CPU topology broken warnings are seen
from the Linux guest. The 6 CPUs are associated with NODE#0/1, but
there are no CPUs associated with NODE#2/3/4/5.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-id: 20220503140304.855514-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, the SMP configuration isn't considered when the CPU
topology is populated. In this case, it's impossible to provide
the default CPU-to-NUMA mapping or association based on the socket
ID of the given CPU.
This takes account of SMP configuration when the CPU topology
is populated. The die ID for the given CPU isn't assigned since
it's not supported on arm/virt machine. Besides, the used SMP
configuration in qtest/numa-test/aarch64_numa_cpu() is corrcted
to avoid testing failure
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20220503140304.855514-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sbsa-ref machine is continuously evolving. Some of the changes we
want to make in the near future, to align with real components (e.g.
the GIC-700), will break compatibility for existing firmware.
Introduce two new properties to the DT generated on machine generation:
- machine-version-major
To be incremented when a platform change makes the machine
incompatible with existing firmware.
- machine-version-minor
To be incremented when functionality is added to the machine
without causing incompatibility with existing firmware.
to be reset to 0 when machine-version-major is incremented.
This versioning scheme is *neither*:
- A QEMU versioned machine type; a given version of QEMU will emulate
a given version of the platform.
- A reflection of level of SBSA (now SystemReady SR) support provided.
The version will increment on guest-visible functional changes only,
akin to a revision ID register found on a physical platform.
These properties are both introduced with the value 0.
(Hence, a machine where the DT is lacking these nodes is equivalent
to version 0.0.)
Signed-off-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20220505113947.75714-1-quic_llindhol@quicinc.com
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the n1 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the a76 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove a possible source of error by removing REGINFO_SENTINEL
and using ARRAY_SIZE (convinently hidden inside a macro) to
find the end of the set of regs being registered or modified.
The space saved by not having the extra array element reduces
the executable's .data.rel.ro section by about 9k.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move ARMCPRegInfo and all related declarations to a new
internal header, out of the public cpu.h.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current fmc model of AST2500 EVB and AST2600 EVB can't emulate quad
mode properly so fix them using equivalent mx25l25635e and mx66u51235f
respectively.
These default settings still can be overridden using the 'fmc-model'
command line option.
Reported-by: Graeme Gregory <quic_ggregory@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220402184427.4010304-1-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The image should be supplied with ELF binary.
$ qemu-system-arm -M ast1030-evb -kernel zephyr.elf -nographic
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-9-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Guest code (u-boot) pokes at this on boot. No functionality is required
for guest code to work correctly, but it helps to document the region
being read from.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220318092211.723938-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ARM virt machine currently uses sysbus-fdt to create device tree
entries for dynamically created MMIO devices.
The RISC-V virt machine can also benefit from this, so move the code to
the core directory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-3-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Arm SMMUv3 includes an optional feature equivalent to the CPU
FEAT_BBM, which permits an OS to switch a range of memory between
"covered by a huge page" and "covered by a sequence of normal pages"
without having to engage in the traditional 'break-before-make'
dance. (This is particularly important for the SMMU, because devices
performing I/O through an SMMU are less likely to be able to cope with
the window in the sequence where an access results in a translation
fault.) The SMMU spec explicitly notes that one of the valid ways to
be a BBM level 2 compliant implementation is:
* if there are multiple entries in the TLB for an address,
choose one of them and use it, ignoring the others
Our SMMU TLB implementation (unlike our CPU TLB) does allow multiple
TLB entries for an address, because the translation table level is
part of the SMMUIOTLBKey, and so our IOTLB hashtable can include
entries for the same address where the leaf was at different levels
(i.e. both hugepage and normal page). Our TLB lookup implementation in
smmu_iotlb_lookup() will always find the entry with the lowest level
(i.e. it prefers the hugepage over the normal page) and ignore any
others. TLB invalidation correctly removes all TLB entries matching
the specified address or address range (unless the guest specifies the
leaf level explicitly, in which case it gets what it asked for). So we
can validly advertise support for BBML level 2.
Note that we still can't yet advertise ourselves as an SMMU v3.2,
because v3.2 requires support for the S2FWB feature, which we don't
yet implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220426160422.2353158-4-peter.maydell@linaro.org
Make the translation error message prettier by adding a missing space
before the parenthesis.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220427111543.124620-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Record bit in the Context Descriptor tells the SMMU to report fault
events to the event queue. Since we don't cache the Record bit at the
moment, access faults from a cached Context Descriptor are never
reported. Store the Record bit in the cached SMMUTransCfg.
Fixes: 9bde7f0674 ("hw/arm/smmuv3: Implement translate callback")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220427111543.124620-1-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It always calls the IOMMU MR translate() callback with flag=IOMMU_NONE in
memory_region_iommu_replay(). Currently, smmuv3_translate() return an
IOMMUTLBEntry with perm set to IOMMU_NONE even if the translation success,
whereas it is expected to return the actual permission set in the table
entry.
So pass the actual perm to returned IOMMUTLBEntry in the table entry.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1650094695-121918-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the TCG GICv4 to the virt board. For the board,
the GICv4 is very similar to the GICv3, with the only difference
being the size of the redistributor frame. The changes here are thus:
* calculating virt_redist_capacity correctly for GICv4
* changing various places which were "if GICv3" to be "if not GICv2"
* the commandline option handling
Note that using GICv4 reduces the maximum possible number of CPUs on
the virt board from 512 to 317, because we can now only fit half as
many redistributors into the redistributor regions we have defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-42-peter.maydell@linaro.org
In several places in virt.c we calculate the number of redistributors that
fit in a region of our memory map, which is the size of the region
divided by the size of a single redistributor frame. For GICv4, the
redistributor frame is a different size from that for GICv3. Abstract
out the calculation of redistributor region capacity so that we have
one place we need to change to handle GICv4 rather than several.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-41-peter.maydell@linaro.org
Everywhere we need to check which GIC version we're using, we look at
vms->gic_version and use the VIRT_GIC_VERSION_* enum values, except
in create_gic(), which copies vms->gic_version into a local 'int'
variable and makes direct comparisons against values 2 and 3.
For consistency, change this function to check the GIC version
the same way we do elsewhere. This includes not implicitly relying
on the enumeration type values happening to match the integer
'revision' values the GIC device object wants.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-40-peter.maydell@linaro.org
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/allwinner-a10.c: In function ‘aw_a10_realize’:
../hw/arm/allwinner-a10.c:135:35: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 8 [-Werror=format-overflow=]
135 | sprintf(bus, "usb-bus.%d", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-15-marcandre.lureau@redhat.com>
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/digic.c: In function ‘digic_init’:
../hw/arm/digic.c:45:54: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
45 | snprintf(name, DIGIC_TIMER_NAME_MLEN, "timer[%d]", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-14-marcandre.lureau@redhat.com>
This patch uses the defined fields to describe PWRON STRAPs for
better readability.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20220411165842.3912945-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-3-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-2-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only time we use the int_combiner_irq[] and ext_combiner_irq[]
arrays in the Exynos4210Irq struct is during realize of the SoC -- we
initialize them with the input IRQs of the combiner devices, and then
connect those to outputs of other devices in
exynos4210_init_board_irqs(). Now that the combiner objects are
easily accessible as s->int_combiner and s->ext_combiner we can make
the connections directly from one device to the other without going
via these arrays.
Since these are the only two remaining elements of Exynos4210Irq,
we can remove that struct entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-19-peter.maydell@linaro.org
Switch the creation of the combiner devices to the new-style
"embedded in state struct" approach, so we can easily refer
to the object elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-18-peter.maydell@linaro.org
At this point, the function exynos4210_init_board_irqs() splits input
IRQ lines to connect them to the input combiner, output combiner and
external GIC. The function exynos4210_combiner_get_gpioin() splits
some of the combiner input lines further to connect them to multiple
different inputs on the combiner.
Because (unlike qemu_irq_split()) the TYPE_SPLIT_IRQ device has a
configurable number of outputs, we can do all this in one place, by
making exynos4210_init_board_irqs() add extra outputs to the splitter
device when it must be connected to more than one input on each
combiner.
We do this with a new data structure, the combinermap, which is an
array each of whose elements is a list of the interrupt IDs on the
combiner which must be tied together. As we loop through each
interrupt ID, if we find that it is the first one in one of these
lists, we configure the splitter device with eonugh extra outputs and
wire them up to the other interrupt IDs in the list.
Conveniently, for all the cases where this is necessary, the
lowest-numbered interrupt ID in each group is in the range of the
external combiner, so we only need to code for this in the first of
the two loops in exynos4210_init_board_irqs().
The old code in exynos4210_combiner_get_gpioin() which is being
deleted here had several problems which don't exist in the new code
in its handling of the multi-core timer interrupts:
(1) the case labels specified bits 4 ... 8, but bit '8' doesn't
exist; these should have been 4 ... 7
(2) it used the input irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]
multiple times as the input of several different splitters,
which isn't allowed
(3) in an apparent cut-and-paste error, the cases for all the
multi-core timer inputs used "bit + 4" even though the
bit range for the case was (intended to be) 4 ... 7, which
meant it was looking at non-existent bits 8 ... 11.
None of these exist in the new code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-17-peter.maydell@linaro.org
The combiner_grp_to_gic_id[] array includes the EXT_GIC_ID_MCT_G0
and EXT_GIC_ID_MCT_G1 multiple times. This means that we will
connect multiple IRQs up to the same external GIC input, which
is not permitted. We do the same thing in the code in
exynos4210_init_board_irqs() because the conditionals selecting
an irq_id in the first loop match multiple interrupt IDs.
Overall we do this for interrupt IDs
(1, 4), (12, 4), (35, 4), (51, 4), (53, 4) for EXT_GIC_ID_MCT_G0
and
(1, 5), (12, 5), (35, 5), (51, 5), (53, 5) for EXT_GIC_ID_MCT_G1
These correspond to the cases for the multi-core timer that we are
wiring up to multiple inputs on the combiner in
exynos4210_combiner_get_gpioin(). That code already deals with all
these interrupt IDs being the same input source, so we don't need to
connect the external GIC interrupt for any of them except the first
(1, 4) and (1, 5). Remove the array entries and conditionals which
were incorrectly causing us to wire up extra lines.
This bug didn't cause any visible effects, because we only connect
up a device to the "primary" ID values (1, 4) and (1, 5), so the
extra lines would never be set to a level.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-16-peter.maydell@linaro.org
Currently for the interrupts MCT_G0 and MCT_G1 which are
the only ones in the input range of the external combiner
and which are also wired to the external GIC, we connect
them only to the internal combiner and the external GIC.
This seems likely to be a bug, as all other interrupts
which are in the input range of both combiners are
connected to both combiners. (The fact that the code in
exynos4210_combiner_get_gpioin() is also trying to wire
up these inputs on both combiners also suggests this.)
Wire these interrupts up to both combiners, like the rest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-15-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), the loop that handles IRQ lines that
are in a range that applies to the internal combiner only creates a
splitter for those interrupts which go to both the internal combiner
and to the external GIC, but it does nothing at all for the
interrupts which don't go to the external GIC, leaving the
irq_table[] array element empty for those. (This will result in
those interrupts simply being lost, not in a QEMU crash.)
I don't have a reliable datasheet for this SoC, but since we do wire
up one interrupt line in this category (the HDMI I2C device on
interrupt 16,1), this seems like it must be a bug in the existing
QEMU code. Fill in the irq_table[] entries where we're not splitting
the IRQ to both the internal combiner and the external GIC with the
IRQ line of the internal combiner. (That is, these IRQ lines go to
just one device, not multiple.)
This bug didn't have any visible guest effects because the only
implemented device that was affected was the HDMI I2C controller,
and we never connect any I2C devices to that bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-14-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), use the TYPE_SPLIT_IRQ device
instead of qemu_irq_split().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-13-peter.maydell@linaro.org
The function exynos4210_combiner_get_gpioin() currently lives in
exynos4210_combiner.c, but it isn't really part of the combiner
device itself -- it is a function that implements the wiring up of
some interrupt sources to multiple combiner inputs. Move it to live
with the other SoC-level code in exynos4210.c, along with a few
macros previously defined in exynos4210.h which are now used only
in exynos4210.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-11-peter.maydell@linaro.org
The only time we use the ext_gic_irq[] array in the Exynos4210Irq
struct is during realize of the SoC -- we initialize it with the
input IRQs of the external GIC device, and then connect those to
outputs of other devices further on in realize (including in the
exynos4210_init_board_irqs() function). Now that the ext_gic object
is easily accessible as s->ext_gic we can make the connections
directly from one device to the other without going via this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-10-peter.maydell@linaro.org
Switch the creation of the external GIC to the new-style "embedded in
state struct" approach, so we can easily refer to the object
elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-9-peter.maydell@linaro.org
The function exynos4210_init_board_irqs() currently lives in
exynos4210_gic.c, but it isn't really part of the exynos4210.gic
device -- it is a function that implements (some of) the wiring up of
interrupts between the SoC's GIC and combiner components. This means
it fits better in exynos4210.c, which is the SoC-level code. Move it
there. Similarly, exynos4210_git_irq() is used almost only in the
SoC-level code, so move it too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-8-peter.maydell@linaro.org
The exynos4210 code currently has two very similar arrays of IRQs:
* board_irqs is a field of the Exynos4210Irq struct which is filled
in by exynos4210_init_board_irqs() with the appropriate qemu_irqs
for each IRQ the board/SoC can assert
* irq_table is a set of qemu_irqs pointed to from the
Exynos4210State struct. It's allocated in exynos4210_init_irq,
and the only behaviour these irqs have is that they pass on the
level to the equivalent board_irqs[] irq
The extra indirection through irq_table is unnecessary, so coalesce
these into a single irq_table[] array as a direct field in
Exynos4210State which exynos4210_init_board_irqs() fills in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-6-peter.maydell@linaro.org
The only time we use the int_gic_irq[] array in the Exynos4210Irq
struct is in the exynos4210_realize() function: we initialize it with
the GPIO inputs of the a9mpcore device, and then a bit later on we
connect those to the outputs of the internal combiner. Now that the
a9mpcore object is easily accessible as s->a9mpcore we can make the
connection directly from one device to the other without going via
this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-5-peter.maydell@linaro.org
The exynos4210 SoC mostly creates its child devices as if it were
board code. This includes the a9mpcore object. Switch that to a
new-style "embedded in the state struct" creation, because in the
next commit we're going to want to refer to the object again further
down in the exynos4210_realize() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-4-peter.maydell@linaro.org
The Exynos4210 SoC device currently uses a custom device
"exynos4210.irq_gate" to model the OR gate that feeds each CPU's IRQ
line. We have a standard TYPE_OR_IRQ device for this now, so use
that instead.
(This is a migration compatibility break, but that is OK for this
machine type.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-2-peter.maydell@linaro.org
Connect the CRL (Clock Reset LPD) to the Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-5-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the Cortex-R5Fs of the Versal RPU (Real-time Processing Unit)
subsystem.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-3-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create an APU CPU Cluster. This is in preparation to add the RPU.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-2-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 4 TTC timers on the ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220331222017.2914409-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's not possible to provide the guest with the Security extensions
(TrustZone) when using KVM or HVF, because the hardware
virtualization extensions don't permit running EL3 guest code.
However, we weren't checking for this combination, with the result
that QEMU would assert if you tried it:
$ qemu-system-aarch64 -enable-kvm -machine virt,secure=on -cpu host -display none
Unexpected error in object_property_find_err() at ../../qom/object.c:1304:
qemu-system-aarch64: Property 'host-arm-cpu.secure-memory' not found
Aborted
Check for this combination of options and report an error, in the
same way we already do for attempts to give a KVM or HVF guest the
Virtualization or MTE extensions. Now we will report:
qemu-system-aarch64: mach-virt: KVM does not support providing Security extensions (TrustZone) to the guest CPU
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/961
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404155301.566542-1-peter.maydell@linaro.org
Convert the TARGET_WORDS_BIGENDIAN macro, similarly to what was done
with HOST_BIG_ENDIAN. The new TARGET_BIG_ENDIAN macro is either 0 or 1,
and thus should always be defined to prevent misuse.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-8-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Connect the ZynqMP APU Control device.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-7-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the ZynqMP CRF - Clock Reset FPD device.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-5-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an unimplemented SERDES (Serializer/Deserializer) area.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In TCG mode, if gic-version=max we always select GICv3 even if
CONFIG_ARM_GICV3_TCG is unset. We shall rather select GICv2.
This also brings the benefit of fixing qos tests errors for tests
using gic-version=max with CONFIG_ARM_GICV3_TCG unset.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220308182452.223473-3-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix for a potential memory leak
* Aspeed SMC cleanups on the definition of the number of flash devices
* New bletchley-bmc machine, AST2600 based
-----BEGIN PGP SIGNATURE-----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=5VHm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220308' into staging
aspeed queue:
* Fix for a potential memory leak
* Aspeed SMC cleanups on the definition of the number of flash devices
* New bletchley-bmc machine, AST2600 based
# gpg: Signature made Tue 08 Mar 2022 08:19:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220308:
hw: aspeed_gpio: Cleanup stray semicolon after switch
hw/arm/aspeed: add Bletchley machine type
hw/arm/aspeed: allow missing spi_model
hw/block: m25p80: Add support for w25q01jvq
aspeed/smc: Fix error log
aspeed/smc: Let the SSI core layer define the bus name
aspeed/smc: Rename 'max_peripherals' to 'cs_num_max'
aspeed/smc: Remove 'num_cs' field
aspeed: Rework aspeed_board_init_flashes() interface
aspeed/smc: Use max number of CE instead of 'num_cs'
aspeed: Fix a potential memory leak bug in write_boot_rom()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the 'bletchley-bmc' machine type based on the kernel DTS[1] and
hardware schematics available to me. The i2c model is as complete as
the current QEMU models support, but in some cases I substituted devices
that are close enough for present functionality. Strap registers are
kept the same as the AST2600-EVB until I'm able to confirm correct
values with physical hardware.
This has been tested with an openbmc image built from [2] plus a kernel
patch[3] for the SPI flash module.
1. https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts?id=a8c729e966c4e9d033242d948b0e53c2a62d32e2
2. b9432b980d
3. 25b566b9a9
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg : increased number of FMC devices to 2 to match Linux dts ]
Message-Id: <20220305000656.1944589-2-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generally all BMCs will use the fmc_model to hold their own flash
and most will have a spi_model to hold the managed system's flash,
but not all systems do. Add a simple NULL check to allow a system
to set the spi_model as NULL to indicate it should not be instantiated.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Message-Id: <20220305000656.1944589-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used anymore.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the allocation of the flash devices uses the number of
slave selects configured in the SoC realize routine. It is simpler to
use directly the number of FMC devices defined in the machine class
and 1 for spi devices (which is what the SoC does in the back of the
machine).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A memory chunk is allocated with g_new0() and assigned to the variable
'storage'. However, if the branch takes true, there will be only an
error report but not a free operation for 'storage' before function
returns. As a result, a memory leak bug is triggered.
Use g_autofree to fix the issue.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
[ clg: reworked the commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is a Linux kernel bug present until v5.12 that prevents
booting with FEAT_LPA2 enabled. As a workaround for TCG,
disable this feature for machine versions prior to 7.0.
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
When we're using KVM, the PSCI implementation is provided by the
kernel, but QEMU has to tell the guest about it via the device tree.
Currently we look at the KVM_CAP_ARM_PSCI_0_2 capability to determine
if the kernel is providing at least PSCI 0.2, but if the kernel
provides a newer version than that we will still only tell the guest
it has PSCI 0.2. (This is fairly harmless; it just means the guest
won't use newer parts of the PSCI API.)
The kernel exposes the specific PSCI version it is implementing via
the ONE_REG API; use this to report in the dtb that the PSCI
implementation is 1.0-compatible if appropriate. (The device tree
binding currently only distinguishes "pre-0.2", "0.2-compatible" and
"1.0-compatible".)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220224134655.1207865-1-peter.maydell@linaro.org
Support the latest PSCI on TCG and HVF. A 64-bit function called from
AArch32 now returns NOT_SUPPORTED, which is necessary to adhere to SMC
Calling Convention 1.0. It is still not compliant with SMCCC 1.3 since
they do not implement mandatory functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-id: 20220213035753.34577-1-akihiko.odaki@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: update MISMATCH_CHECK checks on PSCI_VERSION macros to match]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AN547 application note URL has changed: update our comment
accordingly. (Rev B is still downloadable from the old URL,
but there is a new Rev C of the document now.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220221094144.426191-1-peter.maydell@linaro.org
With these interfaces missing, TFM would delegate peripherals 0, 1,
2, 3 and 8, and qemu would ignore the delegation of interface 8, as
it thought interface 4 was eth & USB.
This patch corrects this behavior and allows TFM to delegate the
eth & USB peripheral to NS mode.
(The old QEMU behaviour was based on revision B of the AN547
appnote; revision C corrects this error in the documentation,
and this commit brings QEMU in to line with how the FPGA
image really behaves.)
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
Message-id: 20220210210227.3203883-1-jimmy.brisson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added commit message note clarifying that the old behaviour
was a docs issue, not because there were two different versions
of the FPGA image]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
-----BEGIN PGP SIGNATURE-----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=0F2M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220227' into staging
aspeed queue:
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
# gpg: Signature made Sun 27 Feb 2022 08:45:45 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220227:
aspeed/sdmc: Add trace events
aspeed/smc: Add an address mask on segment registers
aspeed: Introduce a create_pca9552() helper
aspeed: rainier: Add strap values taken from hardware
aspeed: rainier: Add i2c LED devices
ast2600: Add Secure Boot Controller model
arm: Remove swift-bmc machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This unifies the way we create the pca9552 devices on the different boards.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
