test-qapi.py doesn't force a specific encoding for stderr or
stdout, but the reference files used by check-qapi-schema are in
UTF-8. This breaks check-qapi-schema under certain circumstances
(e.g. if using the C locale and Python < 3.7).
We need to make sure test-qapi.py always generate UTF-8 output
somehow. On Python 3.7+ we can do it using
`sys.stdout.reconfigure(...)`, but we need a solution that works
with older Python versions.
Instead of trying a hack like reopening sys.stdout and
sys.stderr, we can just tell Python to use UTF-8 for I/O encoding
when running test-qapi.py. Do it by setting PYTHONIOENCODING.
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190506213817.14344-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Newer versions of zipl have the ability to write signature entries to the boot
script for secure boot. We don't yet support secure boot, but we need to skip
over signature entries while reading the boot script in order to maintain our
ability to boot guest operating systems that have a secure bootloader.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <1556543381-12671-1-git-send-email-jjherne@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
atoui() and get_index() pass char values to isdigit(). With a
standard isdigit(), we'd get undefined behavior when the value is
negative. Can't happen as char is unsigned on s390x. Even if it
ould, we're actually using isdigit() from pc-bios/s390-ccw/libc.h
here, which works fine for negative values. Clean up anyway, just
to avoid setting a bad example.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190418145355.21100-6-armbru@redhat.com>
[thuth: updated the commit message]
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Stop using variable length array in dc_zva
* Implement M-profile XPSR GE bits
* Don't enable ARMV7M_EXCP_DEBUG from reset
* armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
* armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
* fix various minor issues to allow building for Windows-on-ARM64
* aspeed: Set SDRAM size
* Allow system registers for KVM guests to be changed by QEMU code
* raspi: Diagnose requests for too much RAM
* virt: Support firmware configuration with -blockdev
-----BEGIN PGP SIGNATURE-----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=hcal
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190507' into staging
target-arm queue:
* Stop using variable length array in dc_zva
* Implement M-profile XPSR GE bits
* Don't enable ARMV7M_EXCP_DEBUG from reset
* armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
* armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
* fix various minor issues to allow building for Windows-on-ARM64
* aspeed: Set SDRAM size
* Allow system registers for KVM guests to be changed by QEMU code
* raspi: Diagnose requests for too much RAM
* virt: Support firmware configuration with -blockdev
# gpg: Signature made Tue 07 May 2019 12:59:30 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190507:
target/arm: Stop using variable length array in dc_zva
target/arm: Implement XPSR GE bits
hw/intc/armv7m_nvic: Don't enable ARMV7M_EXCP_DEBUG from reset
hw/intc/armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
hw/arm/armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
osdep: Fix mingw compilation regarding stdio formats
util/cacheinfo: Use uint64_t on LLP64 model to satisfy Windows ARM64
qga: Fix mingw compilation warnings on enum conversion
QEMU_PACKED: Remove gcc_struct attribute in Windows non x86 targets
arm: aspeed: Set SDRAM size
arm: Allow system registers for KVM guests to be changed by QEMU code
hw/arm/raspi: Diagnose requests for too much RAM
hw/arm/virt: Support firmware configuration with -blockdev
pflash_cfi01: New pflash_cfi01_legacy_drive()
pc: Rearrange pc_system_firmware_init()'s legacy -drive loop
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A recent patch results in qemu-img reporting the backing file format of
vmdk images as vmdk. This broke iotests 110 and 126.
Fixes: 7502be838e
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190415154129.31021-1-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This function combines bdrv_set_backing_hd() and bdrv_replace_node()
so we can use it to simplify the code a bit in commit_start().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 20190403143748.9790-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
There is no need to check for this because all block drivers that have
children implement bdrv_child_perm and all callers already ensure that
bs->drv is set.
Furthermore, if this check would fail then the callers would end up
with uninitialized values for nperm and nshared.
This patch replaces the check with an assertion.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 20190404112953.4058-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
ssh_bdrv_dirname() is basically the generic bdrv_dirname(), except it
takes care not to silently chop off any query string (i.e.,
host_key_check).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20190225190828.17726-3-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This requires some changes to keep iotests 104 and 207 working.
qemu-img info in 104 will now return a filename including the user name
and the port, which need to be filtered by adjusting REMOTE_TEST_DIR in
common.rc. This additional information has to be marked optional,
however (which is simple as REMOTE_TEST_DIR is a regex), because
otherwise 197 and 215 would fail: They use it (indirectly) to filter
qemu-img create output which contains a backing filename they have
passed to it -- which probably does not contain a user name or port
number.
The problem in 207 is a nice one to have: qemu-img info used to return
json:{} filenames, but with this patch it returns nice plain ones. We
now need to adjust the filtering to hide the user name (and port number
while we are at it). The simplest way to do this is to include both in
iotests.remote_filename() so that bdrv_refresh_filename() will not
change it, and then iotests.img_info_log() will filter it correctly
automatically.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20190225190828.17726-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Bitmap data may take a lot of disk space, so it's better to discard it
always.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-id: 1551346019-293202-1-git-send-email-andrey.shinkevich@virtuozzo.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[mreitz: Use the commit message proposed by Vladimir]
Signed-off-by: Max Reitz <mreitz@redhat.com>
No reasons for not reporting found corruptions as corruptions in case
of some internal errors, especially in case of just failed to fix l2
entry (and in this case, missed corruptions may influence comparing
logic, when we calculate difference between corruptions fields of two
results)
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190227131433.197063-6-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Do not count a cluster which is fixed to be ZERO as allocated.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-5-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reduce number of structures ignored in overlap check: when checking
active table ignore active tables, when checking inactive table ignore
inactive ones.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_inc_refcounts_imrt() (through realloc_refcount_array()) can eat
an unpredictable amount of memory on corrupted table entries, which are
referencing regions far beyond the end of file.
Prevent this, by skipping such regions from further processing.
Interesting that iotest 138 checks exactly the behavior which we fix
here. So, change the test appropriately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Increase corruptions_fixed only after successful fix.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
182 fails if qemu has no support for hotplugging of a virtio-blk device.
Using an NBD server instead works just as well for the test, even on
qemus without hotplugging support.
Fixes: 6d0a4a0fb5
Reported-by: Danilo C. L. de Paula <ddepaula@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190417153005.30096-1-mreitz@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
For some particular configurations of ext4, sizing an image to 84
sectors + 1 byte causes test failures when the size of the hole is
rounded to a 4k alignment. Let's instead size things to 128 sectors +
1 byte, as the 64k boundary is more likely to work with various hole
granularities.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190506172111.31594-1-eblake@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
The output of qemu-io changed recently - most tests have been fixed in
commit 36b9986b08 ("tests/qemu-iotests: Fix output of qemu-io
related tests") already, but a qcow1, vmdk, and nbd test were still missing.
Fixes: 99e98d7c9f ("qemu-io: Use error_[gs]et_progname()")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190501134127.21104-1-thuth@redhat.com>
[eblake: squash in NBD 083 fixes]
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
233 generally filters the port, but in two cases does not. If some
other concurrently running application has already taken port 10809,
this will result in an output mismatch. Fix this by applying the
filter in these two cases, too.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190506160529.6955-1-mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The existing code to convert flag bits into strings looks a bit strange
now, and if we ever add more flags, it will look even stranger. Prevent
that from happening by making it look up the flag names in an array.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190405191635.25740-1-mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Currently the dc_zva helper function uses a variable length
array. In fact we know (as the comment above remarks) that
the length of this array is bounded because the architecture
limits the block size and QEMU limits the target page size.
Use a fixed array size and assert that we don't run off it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190503120448.13385-1-peter.maydell@linaro.org
In the M-profile architecture, if the CPU implements the DSP extension
then the XPSR has GE bits, in the same way as the A-profile CPSR. When
we added DSP extension support we forgot to add support for reading
and writing the GE bits, which are stored in env->GE. We did put in
the code to add XPSR_GE to the mask of bits to update in the v7m_msr
helper, but forgot it in v7m_mrs. We also must not allow the XPSR we
pull off the stack on exception return to set the nonexistent GE bits.
Correct these errors:
* read and write env->GE in xpsr_read() and xpsr_write()
* only set GE bits on exception return if DSP present
* read GE bits for MRS if DSP present
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-5-peter.maydell@linaro.org
The M-profile architecture specifies that the DebugMonitor exception
should be initially disabled, not enabled. It should be controlled
by the DEMCR register's MON_EN bit, but we don't implement that
register yet (like most of the debug architecture for M-profile).
Note that BKPT instructions will still work, because they
will be escalated to HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-4-peter.maydell@linaro.org
The non-secure versions of the BFAR and BFSR registers are
supposed to be RAZ/WI if AICR.BFHFNMINS == 0; we were
incorrectly allowing NS code to access the real values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-3-peter.maydell@linaro.org
Rule R_CQRV says that if two pending interrupts have the same
group priority then ties are broken by looking at the subpriority.
We had a comment describing this but had forgotten to actually
implement the subpriority comparison. Correct the omission.
(The further tie break rules of "lowest exception number" and
"secure before non-secure" are handled implicitly by the order
in which we iterate through the exceptions in the loops.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-2-peter.maydell@linaro.org
I encountered the following compilation error on mingw:
/mnt/d/qemu/include/qemu/osdep.h:97:9: error: '__USE_MINGW_ANSI_STDIO' macro redefined [-Werror,-Wmacro-redefined]
#define __USE_MINGW_ANSI_STDIO 1
^
/mnt/d/llvm-mingw/aarch64-w64-mingw32/include/_mingw.h:433:9: note: previous definition is here
#define __USE_MINGW_ANSI_STDIO 0 /* was not defined so it should be 0 */
It turns out that __USE_MINGW_ANSI_STDIO must be set before any
system headers are included, not just before stdio.h.
Signed-off-by: Cao Jiaxi <driver1998@foxmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-id: 20190503003719.10233-1-driver1998@foxmail.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Windows ARM64 uses LLP64 model, which breaks current assumptions.
Signed-off-by: Cao Jiaxi <driver1998@foxmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20190503003707.10185-1-driver1998@foxmail.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The win2qemu[] is supposed to be the conversion table to convert between
STORAGE_BUS_TYPE in Windows SDK and GuestDiskBusType in qga.
But it was incorrectly written that it forces to set a GuestDiskBusType
value to STORAGE_BUS_TYPE, which generates an enum conversion warning in clang.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Cao Jiaxi <driver1998@foxmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20190503003650.10137-1-driver1998@foxmail.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gcc_struct is for x86 only, and it generates an warning on ARM64 Clang/MinGW targets.
Signed-off-by: Cao Jiaxi <driver1998@foxmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20190503003618.10089-1-driver1998@foxmail.com
[PMM: dropped the slirp change as slirp is now a submodule]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the Arm implementations of kvm_arch_{get,put}_registers()
don't support having QEMU change the values of system registers
(aka coprocessor registers for AArch32). This is because although
kvm_arch_get_registers() calls write_list_to_cpustate() to
update the CPU state struct fields (so QEMU code can read the
values in the usual way), kvm_arch_put_registers() does not
call write_cpustate_to_list(), meaning that any changes to
the CPU state struct fields will not be passed back to KVM.
The rationale for this design is documented in a comment in the
AArch32 kvm_arch_put_registers() -- writing the values in the
cpregs list into the CPU state struct is "lossy" because the
write of a register might not succeed, and so if we blindly
copy the CPU state values back again we will incorrectly
change register values for the guest. The assumption was that
no QEMU code would need to write to the registers.
However, when we implemented debug support for KVM guests, we
broke that assumption: the code to handle "set the guest up
to take a breakpoint exception" does so by updating various
guest registers including ESR_EL1.
Support this by making kvm_arch_put_registers() synchronize
CPU state back into the list. We sync only those registers
where the initial write succeeds, which should be sufficient.
This commit is the same as commit 823e1b3818 which we
had to revert in commit 942f99c825, except that the bug
which was preventing EDK2 guest firmware running has been fixed:
kvm_arm_reset_vcpu() now calls write_list_to_cpustate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
The Raspberry Pi boards have a physical memory map which does
not allow for more than 1GB of RAM. Currently if the user tries
to ask for more then we fail in a confusing way:
$ qemu-system-aarch64 --machine raspi3 -m 8G
Unexpected error in visit_type_uintN() at qapi/qapi-visit-core.c:164:
qemu-system-aarch64: Parameter 'vcram-base' expects uint32_t
Aborted (core dumped)
Catch this earlier and diagnose it with a more friendly message:
$ qemu-system-aarch64 --machine raspi3 -m 8G
qemu-system-aarch64: Requested ram size is too large for this machine: maximum is 1GB
Fixes: https://bugs.launchpad.net/qemu/+bug/1794187
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Factored out of pc_system_firmware_init() so the next commit can reuse
it in hw/arm/virt.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-3-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The loop does two things: map legacy -drive to properties, and collect
all the backends for use after the loop. The next patch will factor
out the former for reuse in hw/arm/virt.c. To make that easier,
rearrange the loop so it does the first thing first, and the second
thing second.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-2-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* pvrdma: Add support for SRQ
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJczZUsAAoJEDbUwPDPL+Rt/ooH/jZ6Gn325xTl8HYyJ/jJauM1
OTQpY0NuMR30lFc16pGezOuvkahrh5Nwf0oKBCDbiJGVz+6qfCsmUCeem6zKQuCs
e6VEGZPDpK3FG/2gZ4zguy0C2YPsjsDNXXRS0e6Xu5dnLrsaZ+dzoRTtjKf783qr
xVQ6wxDvMICVxtcCglWSd4U5azttpjxccj4nqCg9+q/R7YMTw+Gsp7e2Cti8Uc2I
LaOgm4+waK5Y8cLNRazPfy1Oonx5+YWPJ5KuNG+AUhm2F6pdsqxh8YT2BHdhp3XC
G6Spa9Lw0pORxOXWvZVqGTpATa0zpW2v4NuTeM/EoT5DZ89uY5cCfOz+mbLPtQY=
=UW7h
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/marcel/tags/rdma-pull-request' into staging
RDMA queue
* pvrdma: Add support for SRQ
# gpg: Signature made Sat 04 May 2019 14:35:40 BST
# gpg: using RSA key 36D4C0F0CF2FE46D
# gpg: Good signature from "Marcel Apfelbaum <marcel.apfelbaum@zoho.com>" [marginal]
# gpg: aka "Marcel Apfelbaum <marcel@redhat.com>" [marginal]
# gpg: aka "Marcel Apfelbaum <marcel.apfelbaum@gmail.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: B1C6 3A57 F92E 08F2 640F 31F5 36D4 C0F0 CF2F E46D
* remotes/marcel/tags/rdma-pull-request:
hw/pvrdma: Add support for SRQ
hw/rdma: Modify create/destroy QP to support SRQ
hw/rdma: Add support for managing SRQ resource
hw/rdma: Add SRQ support to backend layer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move it together with the other EDID code. hw/i2c should only
include the core and the adapters, not the slaves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190325155923.30987-1-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix the check preventing calling pixman functions that would access
memory outside allocated vram. The r128 X driver sometimes seem to try
blits that span outside vram, this check prevents crashing QEMU in
that case. (The r128 X driver may have problems even on real hardware
so I'm not sure if it's a client bug or emulation problem but at least
QEMU should survive.)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190409110732.5C5FF7465DB@zero.eik.bme.hu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The SPICE_RING_PROD_ITEM() macro is initializing a local
'uint64_t *' variable to point to the 'el' field inside
the QXLReleaseRing struct. This uint64_t field is not
guaranteed aligned as the struct is packed.
Code should not take the address of fields within a
packed struct. Changing the SPICE_RING_PROD_ITEM()
macro to avoid taking the address of the field is
impractical. It is clearer to just remove the macro
and inline its functionality in the three call sites
that need it.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190412121626.19829-6-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Provide help output similar to other argument help handling:
$ qemu-system-x86_64 -vga help
none
std standard VGA (default)
cirrus Cirrus VGA
vmware VMWare SVGA
xenfb
qxl QXL VGA
virtio Virtio VG
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412152713.16018-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit ce3cf70eda split the ISA device out of the PCI one,
but forgot to remove the "hw/loader.h" header inclusion (the ISA
device calls rom_add_vga()). Remove the now unused include.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20190505225640.4592-1-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The documentation URL is not working, but is backed up by the
Wayback Machine on the Internet Archive.
Replace the outdated link by a captured one.
Add another link to the VGADOC4b.ZIP archive content.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190504121650.12651-1-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When releasing spice resources in release_resource() routine,
if release info object 'ext.info' is null, it leads to null
pointer dereference. Add check to avoid it.
Reported-by: Bugs SysSec <bugs-syssec@rub.de>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20190425063534.32747-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
