Dell Equallogic iSCSI SANs have a very unusual advertised geometry:
$ iscsi-inq -e 1 -c $((0xb0)) iscsi://XXX/0
wsnz:0
maximum compare and write length:1
optimal transfer length granularity:0
maximum transfer length:0
optimal transfer length:0
maximum prefetch xdread xdwrite transfer length:0
maximum unmap lba count:30720
maximum unmap block descriptor count:2
optimal unmap granularity:30720
ugavalid:1
unmap granularity alignment:0
maximum write same length:30720
which says that both the maximum and the optimal discard size
is 15M. It is not immediately apparent if the device allows
discard requests not aligned to the optimal size, nor if it
allows discards at a finer granularity than the optimal size.
I tried to find details in the SCSI Commands Reference Manual
Rev. A on what valid values of maximum and optimal sizes are
permitted, but while that document mentions a "Block Limits
VPD Page", I couldn't actually find documentation of that page
or what values it would have, or if a SCSI device has an
advertisement of its minimal unmap granularity. So it is not
obvious to me whether the Dell Equallogic device is compliance
with the SCSI specification.
Fortunately, it is easy enough to support non-power-of-2 sizing,
even if it means we are less efficient than truly possible when
targetting that device (for example, it means that we refuse to
unmap anything that is not a multiple of 15M and aligned to a
15M boundary, even if the device truly does support a smaller
granularity where unmapping actually works).
Reported-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1469129688-22848-5-git-send-email-eblake@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all drivers have a byte-based .bdrv_co_pdiscard(), we
no longer need to worry about the sector-based version. We can
also relax our minimum alignment to 1 for drivers that support it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-18-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There's enough drivers with a sector-based callback that it will
be easier to switch one at a time. This patch adds a byte-based
callback, and then after all drivers are swapped, we'll drop the
sector-based callback.
[checkpatch doesn't like the space after coroutine_fn in
block_int.h, but it's consistent with the rest of the file]
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-10-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based driver callback .bdrv_aio_discard() with a new
byte-based .bdrv_aio_pdiscard(). Only raw-posix and RBD drivers
are affected, so it was not worth splitting into multiple patches.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-9-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based bdrv_aio_discard() with a new byte-based
bdrv_aio_pdiscard(), which silently ignores any unaligned head
or tail. Driver callbacks will be converted in followup patches.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 1468624988-423-5-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
BlockRequest is the internal struct used by bdrv_aio_*. At the
moment, all such calls were sector-based, but we will eventually
convert to byte-based; start by changing the internal variables
to be byte-based. No change to behavior, although the read and
write code can now go byte-based through more of the stack.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 1468624988-423-4-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based bdrv_discard() with a new byte-based
bdrv_pdiscard(), which silently ignores any unaligned head
or tail.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-3-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based bdrv_co_discard() with a new byte-based
bdrv_co_pdiscard(), which silently ignores any unaligned head
or tail. Driver callbacks will be converted in followup patches.
By calculating the alignment outside of the loop, and clamping
the max discard to an aligned value, we can simplify the actions
done within the loop.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-2-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drivers should be able to rely on the block layer honoring the
max transfer length, rather than needing to return -EINVAL
(iscsi) or manually fragment things (nbd). We already fragment
write zeroes at the block layer; this patch adds the fragmentation
for normal writes, after requests have been aligned (fragmenting
before alignment would lead to multiple unaligned requests, rather
than just the head and tail).
When fragmenting a large request where FUA was requested, but
where we know that FUA is implemented by flushing all requests
rather than the given request, then we can still get by with
only one flush. Note, however, that we need a followup patch
to the raw format driver to avoid a regression in the number of
flushes actually issued.
The return value was previously nebulous on success (sometimes
zero, sometimes the length written); since we never have a short
write, and since fragmenting may store yet another positive
value in 'ret', change the function to always return 0 on success,
matching what we do in bdrv_aligned_preadv().
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 1468607524-19021-4-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drivers should be able to rely on the block layer honoring the
max transfer length, rather than needing to return -EINVAL
(iscsi) or manually fragment things (nbd). This patch adds
the fragmentation in the block layer, after requests have been
aligned (fragmenting before alignment would lead to multiple
unaligned requests, rather than just the head and tail).
The return value was previously nebulous on success on whether
it was zero or the length read; and fragmenting may introduce
yet other non-zero values if we use the last length read. But
as at least some callers are sloppy and expect only zero on
success, it is easiest to just guarantee 0.
[Fix uninitialized ret local variable in bdrv_aligned_preadv().
--Stefan]
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 1468607524-19021-2-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some guests (win2008 server for example) do a lot of unnecessary
flushing when underlying media has not changed. This adds additional
overhead on host when calling fsync/fdatasync.
This change introduces a write generation scheme in BlockDriverState.
Current write generation is checked against last flushed generation to
avoid unnessesary flushes.
The problem with excessive flushing was found by a performance test
which does parallel directory tree creation (from 2 processes).
Results improved from 0.424 loops/sec to 0.432 loops/sec.
Each loop creates 10^3 directories with 10 files in each.
This affected some blkdebug testcases that were expecting error logs from
failure-injected flushes which are now skipped entirely
(tests 026 071 089).
This also affects the performance of block jobs and thus BLOCK_JOB_READY
events for driver-mirror and active block-commit commands now arrives
faster, before QMP send successfully returns to caller (tests 141 144).
Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1468870792-7411-5-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
In practice the entry argument is always known at creation time, and
it is confusing that sometimes qemu_coroutine_enter is used with a
non-NULL argument to re-enter a coroutine (this happens in
block/sheepdog.c and tests/test-coroutine.c). So pass the opaque value
at creation time, for consistency with e.g. aio_bh_new.
Mostly done with the following semantic patch:
@ entry1 @
expression entry, arg, co;
@@
- co = qemu_coroutine_create(entry);
+ co = qemu_coroutine_create(entry, arg);
...
- qemu_coroutine_enter(co, arg);
+ qemu_coroutine_enter(co);
@ entry2 @
expression entry, arg;
identifier co;
@@
- Coroutine *co = qemu_coroutine_create(entry);
+ Coroutine *co = qemu_coroutine_create(entry, arg);
...
- qemu_coroutine_enter(co, arg);
+ qemu_coroutine_enter(co);
@ entry3 @
expression entry, arg;
@@
- qemu_coroutine_enter(qemu_coroutine_create(entry), arg);
+ qemu_coroutine_enter(qemu_coroutine_create(entry, arg));
@ reentry @
expression co;
@@
- qemu_coroutine_enter(co, NULL);
+ qemu_coroutine_enter(co);
except for the aforementioned few places where the semantic patch
stumbled (as expected) and for test_co_queue, which would otherwise
produce an uninitialized variable warning.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is the final patch for converting the common I/O path to take
a BdrvChild parameter instead of BlockDriverState.
The completion of this conversion means that all users that perform I/O
on an image need to actually hold a reference (in the form of BdrvChild,
possible as part of a BlockBackend) to that image. This also protects
against inconsistent use of BlockBackend vs. BlockDriverState functions
because direct use of a BlockDriverState isn't possible any more and
blk->root is private for block-backends.c.
In addition, we can now distinguish different users in the I/O path,
and the future op blockers work is going to add assertions based on
permissions stored in BdrvChild.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
It makes more sense to have ALL block size limit constraints
in the same struct. Improve the documentation while at it.
Simplify a couple of conditionals, now that we have audited and
documented that request_alignment is always non-zero.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
During bdrv_merge_limits(), we were computing initial limits
based on another BDS in two places. At first glance, the two
computations are not identical (one is doing straight copying,
the other is doing merging towards or away from zero) - but
when you realize that the first round is starting with all-0
memory, all of the merging happens to work. Factoring out the
merging makes it easier to track how two BDS limits are merged,
in case we have future reasons to merge in even more limits.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_discard and
discard_alignment. Rename them, using 'pdiscard' as an aid to
track which remaining discard interfaces need conversion, and so
that the compiler will help us catch the change in semantics
across any rebased code. The BlockLimits type is now completely
byte-based; and in iscsi.c, sector_limits_lun2qemu() is no
longer needed.
pdiscard_alignment is made unsigned (we use power-of-2 alignments
as bitmasks, where unsigned is easier to think about) while
leaving max_pdiscard signed (since we still have an 'int'
interface); this is comparable to what commit cf081fc did for
write zeroes limits. We may later want to make everything an
unsigned 64-bit limit - but that requires a bigger code audit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_transfer_length
and opt_transfer_length. Rename them (dropping the _length suffix)
so that the compiler will help us catch the change in semantics
across any rebased code, and improve the documentation. Use unsigned
values, so that we don't have to worry about negative values and
so that bit-twiddling is easier; however, we are still constrained
by 2^31 of signed int in most APIs.
When a value comes from an external source (iscsi and raw-posix),
sanitize the results to ensure that opt_transfer is a power of 2.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to eventually stick request_alignment alongside other
BlockLimits, but first, we must ensure it is populated at the
same time as all other limits, rather than being a special case
that is set only when a block is first opened.
Now that all drivers have been updated to supply an override
of request_alignment during their .bdrv_refresh_limits(), as
needed, the block layer itself can defer setting the default
alignment until part of the overall bdrv_refresh_limits().
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If the amount of data to read ends exactly on the total size
of the bs, then we were wasting time creating a local qiov
to read the data in preparation for what would normally be
appending zeroes beyond the end, even though this corner case
has nothing further to do.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We don't pass any flags on to drivers to handle. Tighten an
assert to explain why we pass 0 to bdrv_driver_preadv(), and add
some comments on things to be aware of if we want to turn on
per-BDS BDRV_REQ_FUA support during reads in the future. Also,
document that we may want to consider using unmap during
copy-on-read operations where the read is all zeroes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For symmetry with bdrv_aligned_preadv(), assert that the caller
really has aligned things properly. This requires adding an align
parameter, which is used now only in the new asserts, but will
come in handy in a later patch that adds auto-fragmentation to the
max transfer size, since that value need not always be a multiple
of the alignment, and therefore must be rounded down.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is mandatory for correct backup creation. In the other case the
content under this area would be lost.
Dirty bits are set exactly like in bdrv_aligned_pwritev, i.e. they are set
even if notifier has returned a error.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy<vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1466093381-6120-4-git-send-email-den@openvz.org
CC: Fam Zheng <famz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Actually we must set dirty bitmap dirty after we have written all our
zeroes for correct processing in drive mirror code. In the other case
we can face not zeroes in this area in mirror_iteration.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy<vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1466093381-6120-3-git-send-email-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The request area is specified in bytes, not in sectors.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy<vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1466093381-6120-2-git-send-email-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_drain_all() pauses all block jobs by using bdrv_next() to iterate
over all top-level BlockDriverStates. Therefore the code is unable to
find block jobs in other nodes.
This patch uses block_job_next() to iterate over all block jobs.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 55ee7d7d4a65c28aa1a1b28823897ef326f328e2.1464346103.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
It is always true for open images now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows drivers to share code between normal I/O and vmstate
accesses.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The return value of .bdrv_load/save_vmstate() can be any non-negative
number in case of success now. It used to be bytes/-errno.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This brings it in line with .bdrv_save_vmstate().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
We already have a byte-based bdrv_pwritev(), but the read counterpart
was still missing. This commit adds it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
If block drivers say that they can do an alignment < 512 bytes, let's
just suppose they mean it. raw-posix used to be an offender with respect
to this, but it can actually deal with byte-aligned requests now.
The default is still 512 bytes for any drivers that only implement
sector-based interfaces, but it is 1 now for drivers that implement
.bdrv_co_preadv.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch makes bdrv_aligned_preadv() ready to accept byte-aligned
requests. Note that this doesn't mean that such requests are actually
made. The caller still ensures that all requests are aligned to at least
512 bytes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
In a first step to convert the common I/O path to work on bytes rather
than sectors, this converts the copy-on-read logic that is used by
bdrv_aligned_preadv().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a new BDRV_REQ_MASK constant, and use it to make sure that
caller flags are always valid.
Tested with 'make check' and with qemu-iotests on both '-raw'
and '-qcow2'; the only failure turned up was fixed in the
previous commit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drivers that implement .bdrv_co_pwritev() get the flags passed as an
argument to said function, but we also unconditionally emulate the flags
anyway. We shouldn't do that.
Fix this by clearing all flags that the driver supports natively after
it returns from .bdrv_co_pwritev().
Fixes: 4df863f3 ('block: Make supported_write_flags a per-bds property')
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Now that all drivers have been converted to a byte interface,
we no longer need a sector interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Rename to bdrv_pwrite_zeroes() to let the compiler ensure we
cater to the updated semantics. Do the same for bdrv_co_write_zeroes().
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Update bdrv_co_do_write_zeroes() to be byte-based, and select
between the new byte-based bdrv_co_pwrite_zeroes() or the old
bdrv_co_write_zeroes(). The next patches will convert drivers,
then remove the old interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
