Any extra draw call for the same blob resource representing guest scanout
before the previous drawing is not finished can break synchronous draw
sequence. To prevent this, drawing is now done only once for each draw
submission (when draw_submitted == true).
v2:
- removed mutex
- updated commit msg
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Message-Id: <20210924225105.24930-1-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The MacOS driver expects a 60.15Hz vertical blank interrupt to be generated by
the framebuffer which in turn schedules the mouse driver via the Vertical Retrace
Manager.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to Apple Technical Note HW26: "Macintosh Quadra Built-In Video" the
in-built framebuffer encodes each 24-bit pixel into 4 bytes. Adjust the 24-bit
RGB pixel encoding accordingly which agrees with the encoding expected by MacOS
when changing into 24-bit colour mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS driver expects the RGB values for the pixel to be in entries 0 and 1
of the colour palette.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The monitor modes table is found by experimenting with the Monitors Control
Panel in MacOS and analysing the reads/writes. From this it can be found that
the mode is controlled by writes to the DAFB_MODE_CTRL1 and DAFB_MODE_CTRL2
registers.
Implement the first block of DAFB registers as a register array including the
existing sense register, the newly discovered control registers above, and also
the DAFB_MODE_VADDR1 and DAFB_MODE_VADDR2 registers which are used by NetBSD to
determine the current video mode.
These experiments also show that the offset of the start of video RAM and the
stride can change depending upon the monitor mode, so update macfb_draw_graphic()
and both the BI_MAC_VADDR and BI_MAC_VROW bootinfo for the q800 machine
accordingly.
Finally update macfb_common_realize() so that only the resolution and depth
supported by the display type can be specified on the command line, and add an
error hint showing the list of supported resolutions and depths if the user tries
to specify an invalid display mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the available resolutions and colour depths are determined by the attached
display type, add a qdev property to allow the display type to be specified.
The main resolutions of interest are high resolution 1152x870 with 8-bit colour
and SVGA resolution up to 800x600 with 24-bit colour so update the q800 machine
to allow high resolution mode if specified and otherwise fall back to SVGA.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM uses the monitor sense to detect the display type and then
offer a fixed set of resolutions and colour depths accordingly. Implement the
monitor sense using information found in Apple Technical Note HW26: "Macintosh
Quadra Built-In Video" along with some local experiments.
Since the default configuration is 640 x 480 with 8-bit colour then hardcode
the sense register to return MACFB_DISPLAY_VGA for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently macfb_common_realize() defines the framebuffer RAM memory region as
being non-migrateable but then immediately registers it for migration. Replace
memory_region_init_ram_nomigrate() with memory_region_init_ram() which is clearer
and does exactly the same thing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The palette_current index counter has a maximum size of 256 * 3 to cover a full
color palette of 256 RGB entries. Linux assumes that the palette_current index
wraps back around to zero after writing 256 RGB entries so ensure that
palette_current is reset at this point to prevent data corruption within
MacfbState.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
During realize memory_region_init_ram_nomigrate() is used to initialise the RAM
memory region used for the framebuffer but the owner object reference is
incorrect since MacFbState is a typedef and not a QOM type.
Change the memory region owner to be the corresponding DeviceState to fix the
issue and prevent random crashes during macfb_common_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 8ac919a065 ("hw/m68k: add Nubus macfb video card")
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
As per the current Error API best practices, change macfb_commom_realize() to return
a boolean indicating success to reduce errp boiler-plate handling code. Note that
memory_region_init_ram_nomigrate() is also updated to use &error_abort to indicate
a non-recoverable error, matching the behaviour recommended after similar
discussions on memory API failures for the recent nubus changes.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Make sure any errors that occur within the macfb realize chain are detected
and handled correctly to prevent crashes and to ensure that error messages are
reported back to the user.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The macfb device is an on-board framebuffer and so is initialised by the
system declaration ROM included within the MacOS toolbox ROM.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Adding this callback provides a way to resume the processing of
cmds in fenceq and cmdq that were not processed because the UI
was waiting on a fence and blocked cmd processing.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-6-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create sync objects and fences only for dmabufs that are blobs. Once a
fence is created (after glFlush) and is signalled,
graphic_hw_gl_flushed() will be called and virtio-gpu cmd processing
will be resumed.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The CDE desktop on HP-UX 10 shows wrongly rendered pixels when the local screen
menu is closed. This bug was introduced by commit c7050f3f16
("hw/display/artist: Refactor x/y coordination extraction") which converted the
coordinate extraction in artist_vram_read() and artist_vram_write() to use the
ADDR_TO_X and ADDR_TO_Y macros, but forgot to right-shift the address by 2 as
it was done before.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: c7050f3f16 ("hw/display/artist: Refactor x/y coordination extraction")
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <YK1aPb8keur9W7h2@ls3530>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xlnx_dp_read allows an out-of-bounds read at its default branch because
of an improper index.
According to
https://www.xilinx.com/html_docs/registers/ug1087/ug1087-zynq-ultrascale-registers.html
(DP Module), registers 0x3A4/0x3A4/0x3AC are allowed.
DP_INT_MASK 0x000003A4 32 mixed 0xFFFFF03F Interrupt Mask Register for intrN.
DP_INT_EN 0x000003A8 32 mixed 0x00000000 Interrupt Enable Register.
DP_INT_DS 0x000003AC 32 mixed 0x00000000 Interrupt Disable Register.
In xlnx_dp_write, when the offset is 0x3A8 and 0x3AC, the virtual device
will write s->core_registers[0x3A4
>> 2]. That is to say, the maxize of s->core_registers could be ((0x3A4
>> 2) + 1). However, the current size of s->core_registers is (0x3AF >>
>> 2), that is ((0x3A4 >> 2) + 2), which is out of the range.
In xlxn_dp_read, the access to offset 0x3A8 or 0x3AC will be directed to
the offset 0x3A8 (incorrect functionality) or 0x3AC (out-of-bounds read)
rather than 0x3A4.
This patch enforces the read access to offset 0x3A8 and 0x3AC to 0x3A4,
but does not adjust the size of s->core_registers to avoid breaking
migration.
Fixes: 58ac482a66 ("introduce xlnx-dp")
Signed-off-by: Qiang Liu <cyruscyliu@gmail.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <1628059910-12060-1-git-send-email-cyruscyliu@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If users try to add an isa-vga device that was already registered,
still in command line, qemu will crash:
$ qemu-system-mips64el -M pica61 -device isa-vga
RAMBlock "vga.vram" already registered, abort!
Aborted (core dumped)
That particular board registers the device automaticaly, so it's
not obvious that a VGA device already exists. This patch changes
this behavior by displaying a message and exiting without crashing.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/44
Signed-off-by: Jose R. Ziviani <jziviani@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210817192629.12755-1-jziviani@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When using qemu configured with --enabled-modules, the
generic stubs are used instead of the module symbols:
qemu-system-x86_64: -device virtio-vga,blob=on: cannot enable blob resources without udmabuf
Restrict the stubs to Linux and only link them when
CONFIG_VIRTIO_GPU is disabled (only the modularized
version is available when it is enabled).
Reported-by: Maxim R. <mrom06@ya.ru>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/553
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210823100454.615816-2-philmd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The code should check the opposite condition of res->iov because it will be null
if virtio_gpu_create_mapping_iov fails and actually this checking is not even
required because checking on ret covers all failing cases.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Message-Id: <20210830175033.29233-1-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Before commit 49afbca3b0 ("virtio-gpu: drop
use_virgl_renderer"), use_virgl_renderer was preventing calling GL
functions from non-GL context threads. The innocuously looking
g->parent_obj.use_virgl_renderer = false;
was set the first time virtio_gpu_gl_reset() was called, during
pc_machine_reset() in the main thread. Further virtio_gpu_gl_reset()
calls in IO threads, without associated GL context, were thus skipping
GL calls and avoided warnings or crashes (see also
https://gitlab.freedesktop.org/virgl/virglrenderer/-/issues/226).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210702123221.942432-1-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This avoids failing to initialize virgl and crashing later on, and clear
the user expectations.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210705104218.1161101-1-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This reverts commit 86dbcdd9c7.
The pre-save assert is gone now, so the migration blocker
is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210721093347.338536-3-kraxel@redhat.com>
Since commit 551dbd0846 ("migration: check pre_save return in
vmstate_save_state") the pre_save hook can fail. So lets finally
use that to drop the guest-triggerable assert in qxl_pre_save().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210721093347.338536-2-kraxel@redhat.com>
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
-----BEGIN PGP SIGNATURE-----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=8708
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging
Some qemu updates for IPMI and I2C
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-7-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-6-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
- Extract nanoMIPS, microMIPS, Code Compaction from translate.c
- Allow PCI config accesses smaller than 32-bit on Bonito64 device
- Fix migration of g364fb device on Jazz Magnum
- Fix dp8393x PROM checksum on Jazz Magnum and Quadra 800
- Map the UART devices unconditionally on Jazz Magnum
- Add functional test booting Linux on the Fuloong 2E
-----BEGIN PGP SIGNATURE-----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=rR+B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd/tags/mips-20210702' into staging
MIPS patches queue
- Extract nanoMIPS, microMIPS, Code Compaction from translate.c
- Allow PCI config accesses smaller than 32-bit on Bonito64 device
- Fix migration of g364fb device on Jazz Magnum
- Fix dp8393x PROM checksum on Jazz Magnum and Quadra 800
- Map the UART devices unconditionally on Jazz Magnum
- Add functional test booting Linux on the Fuloong 2E
# gpg: Signature made Fri 02 Jul 2021 16:36:19 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd/tags/mips-20210702:
hw/mips/jazz: Map the UART devices unconditionally
hw/mips/jazz: specify correct endian for dp8393x device
hw/m68k/q800: fix PROM checksum and MAC address storage
qemu/bitops.h: add bitrev8 implementation
dp8393x: remove onboard PROM containing MAC address and checksum
hw/m68k/q800: move PROM and checksum calculation from dp8393x device to board
hw/mips/jazz: move PROM and checksum calculation from dp8393x device to board
dp8393x: convert to trace-events
dp8393x: checkpatch fixes
g364fb: add VMStateDescription for G364SysBusState
g364fb: use RAM memory region for framebuffer
tests/acceptance: Test Linux on the Fuloong 2E machine
hw/pci-host/bonito: Allow PCI config accesses smaller than 32-bit
hw/pci-host/bonito: Trace PCI config accesses smaller than 32-bit
target/mips: Extract nanoMIPS ISA translation routines
target/mips: Extract the microMIPS ISA translation routines
target/mips: Extract Code Compaction ASE translation routines
target/mips: Add declarations for generic TCG helpers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when QEMU attempts to migrate the MIPS magnum machine it crashes due
to a mistake in the g364fb VMStateDescription configuration which expects a
G364SysBusState and not a G364State.
Resolve the issue by adding a new VMStateDescription for G364SysBusState and
embedding the existing vmstate_g364fb VMStateDescription inside it using
VMSTATE_STRUCT.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 97a3f6ffbb ("g364fb: convert to qdev")
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625163554.14879-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Since the migration stream is already broken, we can use this opportunity to
change the framebuffer so that it is migrated as a RAM memory region rather
than as an array of bytes.
In particular this helps the output of the analyze-migration.py tool which
no longer contains a huge array representing the framebuffer contents.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625163554.14879-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
config_len in vhost_user_get_config() is defined by the device, so if
it's larger than VHOST_USER_MAX_CONFIG_SIZE, this is a programming
error. Turn the corresponding check into an assertion.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-6-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Checking scanout_id in virtio_gpu_do_set_scanout() is too late, for the
"resource_id == 0" case (aka disable scanout) the scanout_id is used
unchecked. Move the check into the callers to fix that.
Fixes: e64d4b6a9b ("virtio-gpu: Refactor virtio_gpu_set_scanout")
Fixes: 32db3c63ae ("virtio-gpu: Add virtio_gpu_set_scanout_blob")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/383
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20210604075029.1201478-1-kraxel@redhat.com>
The highest VBE_DISPI_INDEX_ID version supported by QEMU is
VBE_DISPI_ID5. But currently QEMU only allows writing values up to
VBE_DISPI_ID4 to the VBE_DISPI_INDEX_ID register.
As a result of this when a lower version is written to this register and
later VBE_DISPI_ID5 is written back, reads from the register will
continue to report the lower version.
Indeed SeaBIOS is doing that during VGA initialization which causes
guests to always read VBE_DISPI_ID0 instead of the correct version.
Signed-off-by: Dennis Wölfing <denniswoelfing@gmx.de>
Message-Id: <20210607115303.228659-1-denniswoelfing@gmx.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The "nubus-macfb" currently shows up as uncategorized device in
the output of "-device help". Put it into the display category
to fix this ugliness.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210531073255.46286-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If a blob is available for the cursor, copy the data from the blob.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-15-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This API allows Qemu to set the blob allocated by the Guest as
the scanout buffer. If Opengl support is available, then the
scanout buffer would be submitted as a dmabuf to the UI; if not,
a pixman image is created from the scanout buffer and is
submitted to the UI via the display surface.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-14-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Creating a small helper function for updating the scanout
will be useful in the next patch where this needs to be
done early in do_set_scanout before returning.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-13-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These helpers can be useful for creating dmabuf objects from blobs
and submitting them to the UI.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-12-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This API allows Qemu to register the blob allocated by the Guest
as a new resource and map its backing storage.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-10-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add the property bit, configuration flag and other relevant
macros and definitions associated with this feature.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-9-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Instead of passing the attach_backing object to extract nr_entries
and offset, explicitly pass these as arguments to this function.
This will be helpful when adding create_blob API.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-8-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Store the meta-data associated with a FB in a new object
(struct virtio_gpu_framebuffer) and pass the object to set_scanout.
Also move code in set_scanout into a do_set_scanout function.
This will be helpful when adding set_scanout_blob API.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-7-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add helper functions to create a dmabuf for a resource and mmap it.
Also, introduce the fields blob and blob_size so that these helpers
can start to use them but the full picture will emerge only after
adding create_blob API in patch 8 of this series.
To be able to create a dmabuf using the udmabuf driver, Qemu needs
to be lauched with the memfd memory backend like this:
qemu-system-x86_64 -m 8192m -object memory-backend-memfd,id=mem1,size=8192M
-machine memory-backend=mem1
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On some MIPS system, page size is 16K, and qxl vga device can
be used for VM in kvm mode. Qxl pci rom size is set 8K fixed,
smaller than 16K page size on host system, it fails to be
added into memslots in kvm mode where memory_size and GPA
are required to align with page size.
This patch fixes this issue.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <1621340448-31617-1-git-send-email-maobibo@loongson.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
Introduce a symbol which can be used to prevent display modules which
need vga support being loaded into system emulators with CONFIG_VGA=n.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-16-kraxel@redhat.com>
Now that we have separated the gl and non-gl code flows to two different
devices there is little reason turn on and off virglrenderer usage at
runtime. The gl code can simply use virglrenderer unconditionally.
So drop use_virgl_renderer field and just do that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-13-kraxel@redhat.com>
Move device init (realize) and properties.
Drop the virgl property, the virtio-gpu-gl-device has virgl enabled no
matter what. Just use virtio-gpu-device instead if you don't want
enable virgl and opengl. This simplifies the logic and reduces the test
matrix.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-4-kraxel@redhat.com>
Just a skeleton for starters, following patches will add more code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-3-kraxel@redhat.com>
"3d" -> "virgl" as 3d is a rather broad term.
Hopefully a bit less confusing.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-2-kraxel@redhat.com>
dma_memory_map() may map only a part of the request. Happens if the
request can't be mapped in one go, for example due to a iommu creating
a linear dma mapping for scattered physical pages. Should that be the
case virtio-gpu must call dma_memory_map() again with the remaining
range instead of simply throwing an error.
Note that this change implies the number of iov entries may differ from
the number of mapping entries sent by the guest. Therefore the iov_len
bookkeeping needs some updates too, we have to explicitly pass around
the iov length now.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210506091001.1301250-1-kraxel@redhat.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210506091001.1301250-1-kraxel@redhat.com>
The Detailed Timing Descriptor has only 12 bits to store the
resolution. This limits the guest to 4095 pixels.
This patch adds support for the DisplayID extension, that has 2 full
bytes for that purpose, thus allowing 5k resolutions and above.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-3-mail@knazarov.com>
[ kraxel: minor workflow tweaks ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-9-kraxel@redhat.com>
Some of the EDID extensions like DisplayID do checksums of their
subsections. Currently checksums can be only applied to the whole
extension blocks which are 128 bytes.
This patch allows to checksum arbitrary parts of EDID, and not only
whole extension blocks.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-2-mail@knazarov.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-8-kraxel@redhat.com>
The timing generation is currently performed inside the function that
fills in the DTD. The DisplayID generation needs it as well, so moving
it out to a separate function.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-1-mail@knazarov.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-7-kraxel@redhat.com>
When the 4 descriptors in the base edid block are filled, jump to the
dta extension block. This allows for more than four descriptors.
Happens for example when generating an edid blob with a serial number
(qemu-edid -s $serial).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-5-kraxel@redhat.com>
Initialize the "Established timings III" block earlier. Also move up
edid_fill_modes(). That'll make sure the offset for the additional
descriptors in the dta block don't move any more, which in turn makes it
easier to actually use them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-4-kraxel@redhat.com>
Add helper function to find the next free desc block.
Needed when we start to use the dta descriptor entries.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-3-kraxel@redhat.com>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When building with --enable-sanitizers we get:
Direct leak of 16 byte(s) in 1 object(s) allocated from:
#0 0x5618479ec7cf in malloc (qemu-system-aarch64+0x233b7cf)
#1 0x7f675745f958 in g_malloc (/lib64/libglib-2.0.so.0+0x58958)
#2 0x561847c2dcc9 in xlnx_dp_init hw/display/xlnx_dp.c:1259:5
#3 0x56184a5bdab8 in object_init_with_type qom/object.c:375:9
#4 0x56184a5a2bda in object_initialize_with_type qom/object.c:517:5
#5 0x56184a5a24d5 in object_initialize qom/object.c:536:5
#6 0x56184a5a2f6c in object_initialize_child_with_propsv qom/object.c:566:5
#7 0x56184a5a2e60 in object_initialize_child_with_props qom/object.c:549:10
#8 0x56184a5a3a1e in object_initialize_child_internal qom/object.c:603:5
#9 0x5618495aa431 in xlnx_zynqmp_init hw/arm/xlnx-zynqmp.c:273:5
The RX/TX FIFOs are created in xlnx_dp_init(), add xlnx_dp_finalize()
to destroy them.
Fixes: 58ac482a66 ("introduce xlnx-dp")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210323182958.277654-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Windows guests using the "Basic Display Adapter" don't parse the
"Established timings III" block. They also don't parse any edid
extension.
So prefer the "Standard Timings" block to store the display resolutions
in edid_fill_modes(). Also reorder the mode list, so more exotic
resolutions (specifically the ones which are not supported by vgabios)
are moved down and the remaining ones have a better chance to get one of
the eight slots in the "Standard Timings" block.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210316143812.2363588-6-kraxel@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
The template header is now included only once; just inline its contents
in hw/display/pxa2xx_lcd.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-10-peter.maydell@linaro.org
We're about to move code from the template header into pxa2xx_lcd.c.
Before doing that, make coding style fixes so checkpatch doesn't
complain about the patch which moves the code. This commit is
whitespace changes only:
* avoid hard-coded tabs
* fix ident on function prototypes
* no newline before open brace on array definitions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-9-peter.maydell@linaro.org
We're about to move code from the template header into pxa2xx_lcd.c.
Before doing that, make coding style fixes so checkpatch doesn't
complain about the patch which moves the code. This commit fixes
missing braces in the SKIP_PIXEL() macro definition and in if()
statements.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-8-peter.maydell@linaro.org
Now that BITS is always 32, expand out all its uses in the template
header, including removing now-useless uses of the glue() macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-7-peter.maydell@linaro.org
Since the dest_width is now always 4 because the output surface is
32bpp, we can replace the dest_width state field with a constant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-6-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel. Remove the legacy dead code
from the pxa2xx_lcd display device which was handling the possibility
that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-5-peter.maydell@linaro.org
BITS is always 32, so remove all uses of it from the template header,
by dropping the trailing '32' from the draw function names and
not constructing the name of rgb_to_pixel32() via the glue() macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-4-peter.maydell@linaro.org
The pl110_template.h header has a doubly-nested multiple-include pattern:
* pl110.c includes it once for each host bit depth (now always 32)
* every time it is included, it includes itself 6 times, to account
for multiple guest device pixel and byte orders
Now we only have to deal with 32-bit host bit depths, we can move the
code corresponding to the outer layer of this double-nesting to be
directly in pl110.c and reduce the template header to a single layer
of nesting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-3-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel. Remove the legacy dead
code from the pl110 display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-2-peter.maydell@linaro.org
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=/uyx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210310' into staging
ppc patch queue for 2021-03-10
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
# gpg: Signature made Wed 10 Mar 2021 04:08:53 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210310:
spapr.c: send QAPI event when memory hotunplug fails
spapr.c: remove duplicated assert in spapr_memory_unplug_request()
target/ppc: fix icount support on Book-e vms accessing SPRs
qemu_timer.c: add timer_deadline_ms() helper
spapr_pci.c: add 'unplug already in progress' message for PCI unplug
spapr.c: add 'unplug already in progress' message for PHB unplug
hw/ppc: e500: Add missing <ranges> in the eTSEC node
hw/net: fsl_etsec: Fix build error when HEX_DUMP is on
spapr_drc.c: use DRC reconfiguration to cleanup DIMM unplug state
spapr_drc.c: add hotunplug timeout for CPUs
spapr_drc.c: introduce unplug_timeout_timer
target/ppc: Fix bcdsub. emulation when result overflows
docs/system: Extend PPC section
spapr: rename spapr_drc_detach() to spapr_drc_unplug_request()
spapr_drc.c: use spapr_drc_release() in isolate_physical/set_unusable
pseries: Update SLOF firmware image
spapr_drc.c: do not call spapr_drc_detach() in drc_isolate_logical()
hw/display/sm501: Inline template header into C file
hw/display/sm501: Expand out macros in template header
hw/display/sm501: Remove dead code for non-32-bit RGB surfaces
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We no longer need to include sm501_template.h multiple times, so
we can simply inline its contents into sm501.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-4-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we only include sm501_template.h for the DEPTH==32 case, we
can expand out the uses of the BPP, PIXEL_TYPE and PIXEL_NAME macros
in that header.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-3-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the sm501 display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-2-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
