All targets have been converted to allocating space for temporaries
on the stack. No need to allocate space within the CPU_COMMON block.
Signed-off-by: Richard Henderson <rth@twiddle.net>
# By Chegu Vinod
# Via Juan Quintela
* quintela/migration.next:
Force auto-convegence of live migration
Add 'auto-converge' migration capability
Introduce async_run_on_cpu()
Message-id: 1373664508-5404-1-git-send-email-quintela@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Old qemu versions required that 1st s/g entry is the header.
Since QEMU 1.5, patchset titled "virtio-net: iovec handling cleanup"
removed this limitation but a feature bit is needed so guests know it's
safe to lay out header differently.
This patch applies on top and adds such a feature bit to QEMU.
It is set by default for virtio-net.
virtio net header inline with the data is beneficial
for latency and small packet bandwidth - guest driver
code utilizing this feature has been acked but missed 3.11
by a narrow margin, it's pending for 3.12.
This feature bit is cleared by default when compatibility with old
machine types is requested.
Other performance-sensitive devices (blk and scsi)
don't yet support arbitrary s/g layouts, so
we only set this bit for virtio-net for now.
There are plans to allow arbitrary layouts there, but
no code has been posted yet.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently macvtap based macvlan device is working in promiscuous
mode, we want to implement mac-programming over macvtap through
Libvirt for better performance.
Design:
QEMU notifies Libvirt when rx-filter config is changed in guest,
then Libvirt query the rx-filter information by a monitor command,
and sync the change to macvtap device. Related rx-filter config
of the nic contains main mac, rx-mode items and vlan table.
This patch adds a QMP event to notify management of rx-filter change,
and adds a monitor command for management to query rx-filter
information.
Test:
If we repeatedly add/remove vlan, and change macaddr of vlan
interfaces in guest by a loop script.
Result:
The events will flood the QMP client(management), management takes
too much resource to process the events.
Event_throttle API (set rate to 1 ms) can avoid the events to flood
QMP client, but it could cause an unexpected delay (~1ms), guests
guests normally expect rx-filter updates immediately.
So we use a flag for each nic to avoid events flooding, the event
is emitted once until the query command is executed. The flag
implementation could not introduce unexpected delay.
There maybe exist an uncontrollable delay if we let Libvirt do the
real change, guests normally expect rx-filter updates immediately.
But it's another separate issue, we can investigate it when the
work in Libvirt side is done.
Michael S. Tsirkin: tweaked to enable events on start
Michael S. Tsirkin: fixed not to crash when no id
Michael S. Tsirkin: fold in patch:
"additional fixes for mac-programming feature"
Amos Kong: always notify QMP client if mactable is changed
Amos Kong: return NULL list if no net client supports rx-filter query
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If flushing the block devices fails, return an error. The VM is stopped
anyway.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_flush() can fail, and bdrv_flush_all() should return an error as
well if this happens for a block device. It returns the first error
return now, but still at least tries to flush the remaining devices even
in error cases.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
One of the major reasons for doing something new for -blockdev and
blockdev-add was that the old block layer code parses filenames instead
of just taking them literally. So we should really leave it untouched
when it's passing using the new interfaces (like -drive
file.filename=...).
This allows opening relative file names that contain a colon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The auto-converge migration capability allows the user to specify if they
choose live migration seqeunce to automatically detect and force convergence.
Signed-off-by: Chegu Vinod <chegu_vinod@hp.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce an asynchronous version of run_on_cpu() i.e. the caller
doesn't have to block till the call back routine finishes execution
on the target vcpu.
Signed-off-by: Chegu Vinod <chegu_vinod@hp.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The DBDMA engine really just reads bytes from a producing device (IDE
in our case) and shoves these bytes into memory. It doesn't care whether
any alignment takes place or not.
Our code today however assumes that block accesses always happen on
sector (512 byte) boundaries. This is a fair assumption for most cases.
However, Mac OS X really likes to do unaligned, incomplete accesses
that it finishes with the next DMA request.
So we need to read / write the unaligned bits independent of the actual
asynchronous request, because that one can only handle 512-byte-aligned
data. We also need to cache these unaligned sectors until the next DMA
request, at which point the data might be successfully flushed from the
pipe.
Signed-off-by: Alexander Graf <agraf@suse.de>
Soon we will introduce intermediate processing pauses which will
allow the bottom half to restart a DMA request that couldn't be
fulfilled yet.
For that to work, move the processing variable into the io struct
which is what DMA providers work with.
While touching it, also change it into a bool
Signed-off-by: Alexander Graf <agraf@suse.de>
The DBDMA controller has a bottom half to asynchronously process DMA
request queues.
This bh was stored as a gross static variable. Move it into the device
struct instead.
While at it, move all users of it to the new generic kick function.
Signed-off-by: Alexander Graf <agraf@suse.de>
The DBDMA engine really is running all the time, waiting for input. However
we don't want to waste cycles constantly polling.
So introduce a kick function that data providers can call to notify the
DBDMA controller of new input.
Signed-off-by: Alexander Graf <agraf@suse.de>
We usually keep struct and constant definitions in header files. Move
them there to stay consistent and to make access to fields easier.
Signed-off-by: Alexander Graf <agraf@suse.de>
[Issue]
When we offer a customer support service and a problem happens
in a customer's system, we try to understand the problem by
comparing what the customer reports with message logs of the
customer's system.
In this case, we often need to know when the problem happens.
But, currently, there is no timestamp in qemu's error messages.
Therefore, we may not be able to understand the problem based on
error messages.
[Solution]
Add a timestamp to qemu's error message logged by
error_report() with g_time_val_to_iso8601().
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Fix for LP#1187529: Devices on PCI bridge stop working when
live-migrated. Update bridge mappings for all PCI bridge
devices in get_pci_config_device().
Signed-off-by: Don Koch <dkoch@verizon.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
x86 was using additional CPU_DUMP_* flags, so make that configurable in
CPUClass::reset_dump_flags.
This adds reset logging for alpha, unicore32 and xtensa.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since commit 878096eeb2 (cpu: Turn
cpu_dump_{state,statistics}() into CPUState hooks) CPUArchState is no
longer needed.
Add documentation and make the functions available through qemu/log.h
outside NEED_CPU_H to allow use in qom/cpu.c. Moving them to qom/cpu.h
was not yet possible due to convoluted include paths, so that some
devices grow an implicit and unneeded dependency on qom/cpu.h for now.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
[AF: Simplified mb_cpu_do_interrupt() and do_interrupt_all() changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since current_cpu is CPUState it no longer depends on CPUPPCState.
Move ppce500_set_mpic_proxy() to a new hw/ppc/ppc_e500.h because
hw/ppc/ppc.h is too heavily using CPUPPCState and PowerPCCPU.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move next_cpu from CPU_COMMON to CPUState.
Move first_cpu variable to qom/cpu.h.
gdbstub needs to use CPUState::env_ptr for now.
cpu_copy() no longer needs to save and restore cpu_next.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Rebased, simplified cpu_copy()]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since CPU loops are done as last step in kvm_{insert,remove}_breakpoint()
and kvm_remove_all_breakpoints(), we do not need to distinguish between
invoking CPU and iterated CPUs and can thereby free the identifier for
use as a global variable.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
To be used in the next few commits to fix or clean up queries of
"machine" options (-machine and its sugared forms).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1372943363-24081-4-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It seems to be unused since several years (commit
be995c2764 in 2006).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1373044036-14443-1-git-send-email-sw@weilnetz.de
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR2ctmAAoJECgfDbjSjVRpQpAH/Rk00yLrQ2R5ScNa8AL9LeaJ
gVFndBmmuRz4gdhyATx6lzR98ic32iTr0+YR5mL51btgmM5a0bEd/SIu34nXriWj
PsM0wdXfo/oEygdttxhvzJOH17tohRV9xg2WA2d8BEwDzrDyqoQ4J0VJlHlG7u3W
nq4KVDVUpLNQFKG8ZgJ2vW0WMw/mBSj2rluhQUALhcuvChphtvAFZ2rsSfJr6bzD
aBELrtIvfLvPGN/0WVeYs9qlp4EE03H3X6gN61QvV3/YElxubKUV5XyMDOX2dW3D
2j0NQi84LYHn0SFap2r/Kgm47/F6Q56SFk5lrgZrg60mhQTwocw7PfL8CGxjXRI=
=gxxc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,misc enhancements
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 07 Jul 2013 03:11:18 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By David Gibson (10) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pci: Fold host_buses list into PCIHostState functionality
pci: Remove domain from PCIHostBus
pci: Simpler implementation of primary PCI bus
pci: Add root bus parameter to pci_nic_init()
pci: Add root bus argument to pci_get_bus_devfn()
pci: Replace pci_find_domain() with more general pci_root_bus_path()
pci: Use helper to find device's root bus in pci_find_domain()
pci: Abolish pci_find_root_bus()
pci: Move pci_read_devaddr to pci-hotplug-old.c
pci: Cleanup configuration for pci-hotplug.c
pvpanic: fix fwcfg for big endian hosts
pvpanic: initialization cleanup
MAINTAINERS: s/Marcelo/Paolo/
e1000: cleanup process_tx_desc
pc_piix: cleanup init compat handling
pc: pass PCI hole ranges to Guests
pci: store PCI hole ranges in guestinfo structure
range: add Range structure
Message-id: 1373228271-31223-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The host_buses list is an odd structure - a list of pointers to PCI root
buses existing in parallel to the normal qdev tree structure. This patch
removes it, instead putting the link pointers into the PCIHostState
structure, which have a 1:1 relationship to PCIHostBus structures anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At present, pci_nic_init() and pci_nic_init_nofail() assume that they will
only create a NIC under the primary PCI root. As we add support for
multiple PCI roots, that may no longer be the case. This patch adds a root
bus parameter to pci_nic_init() (and updates callers accordingly) to allow
the machine init code using it to specify the right PCI root for NICs
created by old-style -net nic parameters. NICs created new-style, with
-device can of course be put anywhere.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_get_bus_devfn() interprets a full PCI address string to give a PCIBus *
and device/function number within that bus. Currently it assumes it is
working on an address under the primary PCI root bus. This patch extends
it to allow the caller to specify a root bus. This might seem a little odd
since the supplied address can (theoretically) include a PCI domain number.
However, attempting to use a non-zero domain number there is currently an
error, so that shouldn't really cause problems.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_domain() is used in a number of places where we want an id for a
whole PCI domain (i.e. the subtree under a PCI root bus). The trouble is
that many platforms may support multiple independent host bridges with no
hardware supplied notion of domain number.
This patch, therefore, replaces calls to pci_find_domain() with calls to
a new pci_root_bus_path() returning a string. The new call is implemented
in terms of a new callback in the host bridge class, so it can be defined
in some way that's well defined for the platform. When no callback is
available we fall back on the qbus name.
Most current uses of pci_find_domain() are for error or informational
messages, so the change in identifiers should be harmless. The exception
is pci_get_dev_path(), whose results form part of migration streams. To
maintain compatibility with old migration streams, the PIIX PCI host is
altered to always supply "0000" for this path, which matches the old domain
number (since the code didn't actually support domains other than 0).
For the pseries (spapr) PCI bridge we use a different platform-unique
identifier (pseries machines can routinely have dozens of PCI host
bridges). Theoretically that breaks migration streams, but given that we
don't yet have migration support for pseries, it doesn't matter.
Any other machines that have working migration support including PCI
devices will need to be updated to maintain migration stream compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently pci_find_domain() performs two functions - it locates the PCI
root bus above the given bus, then looks up that root bus's domain number.
This patch adds a helper function to perform the first task, finding the
root bus for a given PCI device. This is then used in pci_find_domain().
This changes pci_find_domain()'s signature slightly, taking a PCIDevice
instead of a PCIBus - since all callers passed something of the form
dev->bus, this simplifies things slightly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_root_bus() takes a domain parameter. Currently PCI root buses
with domain other than 0 can't be created, so this is more or less a long
winded way of retrieving the main PCI root bus. Numbered domains don't
actually properly cover the (non x86) possibilities for multiple PCI root
buses, so this patch for now enforces the domain == 0 restriction in other
places to replace pci_find_root_bus() with an explicit
pci_find_primary_bus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This same treatment previously done to phys_node_map and phys_sections
is now applied to the dispatch field of AddressSpace. Topology updates
use as->next_dispatch while accesses use as->dispatch.
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will help having two copies of AddressSpaceDispatch during the
recreation of the radix tree (one being built, and one that is complete
and will be protected by RCU). We do not want to have to unregister and
re-register the listener.
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We're already using them in several places, but __sync builtins are just
too ugly to type, and do not provide seqcst load/store operations.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After the next patch it would not be used elsewhere anyway. Also,
the _nofail and the standard versions of this function return different
things, which is confusing. Removing the function from the public headers
limits the confusion.
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add ref/unref calls at the following places:
- places where memory regions are stashed by a listener and
used outside the BQL (including in Xen or KVM).
- memory_region_find callsites
- creation of aliases and containers (only the aliased/contained
region gets a reference to avoid loops)
- around calls to del_subregion/add_subregion, where the region
could disappear after the first call
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This new API will avoid having too many memory_region_ref/unref
in paths that currently use memory_region_find.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Whenever memory regions are accessed outside the BQL, they need to be
preserved against hot-unplug. MemoryRegions actually do not have their
own reference count; they piggyback on a QOM object, their "owner".
The owner is set at creation time, and there is a function to retrieve
the owner.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This decouples memory.h from ioport.h, concentrating all portio related
types in a single header.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case the latter may vanish one day, make sure the vmport read handler
type will remain unaffected. This is also conceptually cleaner.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove unused ioport_register and isa_unassign_ioport along with
everything that only those services used.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current ioport dispatcher is a complex beast, mostly due to the
need to deal with old portio interface users. But we can overcome it
without converting all portio users by embedding the required base
address of a MemoryRegionPortio access into that data structure. That
removes the need to have the additional MemoryRegionIORange structure
in the loop on every access.
To handle old portio memory ops, we simply install dispatching handlers
for portio memory regions when registering them with the memory core.
This removes the need for the old_portio field.
We can drop the additional aliasing of ioport regions and also the
special address space listener. cpu_in and cpu_out now simply call
address_space_read/write. And we can concentrate portio handling in a
single source file.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Open-code isa_is_ioport_assigned via a memory region lookup. As all IO
ports are now directly or indirectly registered via the memory API, this
becomes possible and will finally allow us to drop the ioport tables.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pci_read_devaddr() is only used by the legacy functions for the old PCI
hotplug interface in pci-hotplug-old.c. So we move the function there,
and make it static.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid use of static variables: PC systems
initialize pvpanic device through pvpanic_init,
so we can simply create the fw_cfg file at that point.
This also makes it possible to skip device
creation completely if fw_cfg is not there, e.g. for xen -
so the ports it reserves are not discoverable by guests.
Also, make pvpanic_init void since callers ignore return
status anyway.
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paul Durrant <Paul.Durrant@citrix.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Guest currently has to jump through lots of hoops to guess the PCI hole
ranges. It's fragile, and makes us change BIOS each time we add a new
chipset. Let's report the window in a ROM file, to make BIOS do exactly
what QEMU intends.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sometimes we need to pass ranges around, add a
handy structure for this purpose.
Note: memory.c defines its own concept of AddrRange structure for
working with 128 addresses. It's necessary there for doing range math.
This is not needed for most users: struct Range is
much simpler, and is only used for passing the range around.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For add, the carry only requires checking one of the arguments.
For sub and neg, we can similarly optimize computation of the
carry.
For ge, we can just do lexicographic order.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Support in fwcfg has been around for exposure of the clock-frequency
CPU property. OpenBIOS reads it, we just never exposed it.
Since Mac OS X is very picky about its clock frequency values, let's
just take a known good value and always expose that.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alexander Graf <agraf@suse.de>
RTAS is a hypervisor provided binary blob that a guest loads and
calls into to execute certain functions. It's similar to the
vsyscall page in Linux or the short lived VMCI paravirt interface
from VMware.
The QEMU implementation of the RTAS blob is simply a passthrough
that proxies all RTAS calls to the hypervisor via an hypercall.
While we pass a CPU argument for hypercall handling in QEMU, we
don't pass it for RTAS calls. Since some RTAs calls require
making hypercalls (normally RTAS is implemented as guest code) we
have nasty hacks to allow that.
Add a CPU argument to RTAS call handling so we can more easily
invoke hypercalls just as guest code would.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Introduce type constant and cast macro.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Enables support for the in-kernel MPIC that thas been merged into the
KVM next branch. This includes irqfd/KVM_IRQ_LINE support from Alex
Graf (along with some other improvements).
Note from Alex regarding kvm_irqchip_create():
On x86, one would call kvm_irqchip_create() to initialize an
in-kernel interrupt controller. That function then goes ahead and
initializes global capability variables as well as the default irq
routing table.
On ppc, we can't call kvm_irqchip_create() because we can have
different types of interrupt controllers. So we want to do all the
things that function would do for us in the in-kernel device init
handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: squash in kvm_irqchip_commit_routes patch, fix non-kvm build,
fix ppcemb]
Signed-off-by: Alexander Graf <agraf@suse.de>
The current logic updates KVM's view of our interrupt map every time we
change it. While this is nice and bullet proof, it slows things down
badly for me. QEMU spends about 3 seconds on every start telling KVM what
news it has on its routing maps.
Instead, let's just synchronize the whole irq routing map as a whole when
we're done constructing it. For things that change during runtime, we can
still update the routing table on demand.
Signed-off-by: Alexander Graf <agraf@suse.de>
On PPC, we can have different types of interrupt controllers, so we really
only know that we are going to use one when we created it.
Export kvm_init_irq_routing() to common code, so that we don't have to call
kvm_irqchip_create().
Signed-off-by: Alexander Graf <agraf@suse.de>
On PPC, we don't support MP state. So far it's not necessary and I'm
not convinced yet that we really need to support it ever.
However, the current idle logic in QEMU assumes that an in-kernel PIC
also means we support MP state. This assumption is not true anymore.
Let's split up the two cases into two different variables. That way
PPC can expose an in-kernel PIC, while not implementing MP state.
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Jan Kiszka <jan.kiszka@siemens.com>
# By Gerd Hoffmann (13) and Michael Tokarev (1)
# Via Michael Tokarev
* mjt/trivial-patches:
doc: we use seabios, not bochs bios
qemu-socket: don't leak opts on error
qemu-char: report udp backend errors
qemu-char: add -chardev mux support
qemu-char: minor mux chardev fixes
qemu-char: use ChardevBackendKind in CharDriver
qemu-char: don't leak opts on error
qemu-char: fix documentation for telnet+wait socket flags
qemu-char: print notification to stderr
qemu-char: use more specific error_setg_* variants
qemu-char: check optional fields using has_*
qemu-socket: catch monitor_get_fd failures
qemu-socket: drop pointless allocation
qemu-socket: zero-initialize SocketAddress
Message-id: 1372443465-22384-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
.has_zero_init defaults to 1 for all formats and protocols.
this is a dangerous default since this means that all
new added drivers need to manually overwrite it to 0 if
they do not ensure that a device is zero initialized
after bdrv_create().
if a driver needs to explicitly set this value to
1 its easier to verify the correctness in the review process.
during review of the existing drivers it turned out
that ssh and gluster had a wrong default of 1.
both protocols support host_devices as backend
which are not by default zero initialized. this
wrong assumption will lead to possible corruption
if qemu-img convert is used to write to such a backend.
vpc and vmdk also defaulted to 1 altough they support
fixed respectively flat extends. this has to be addresses
in separate patches. both formats as well as the mentioned
ssh and gluster are turned to the default of 0 with this
patch for safety.
a similar problem with the wrong default existed for
iscsi most likely because the driver developer did
oversee the default value of 1.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use it for all targets, but be careful not to pass invalid CPUState.
cpu_single_env can be NULL, e.g. on Xen.
Signed-off-by: Andreas Färber <afaerber@suse.de>
While not normally needed for *-user, it can safely be used there since
always based on uint64_t, to avoid ifdeffery.
To avoid accidental uses, move the guards from exec/hwaddr.h to its
inclusion sites. No need for them in include/hw/.
Prepares for hwaddr use in qom/cpu.h.
Signed-off-by: Andreas Färber <afaerber@suse.de>
This allows to move the call into CPUState's realizefn.
Therefore move the stub into libqemustub.a.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use CPUState::env_ptr for now.
Prepares for changing cpu_handle_guest_debug() argument to CPUState.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It no longer uses CPUArchState.
Prepares for changing qemu_kvm_cpu_thread_fn() opaque to CPUState.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make cpustats monitor command available unconditionally.
Prepares for changing kvm_handle_internal_error() and kvm_cpu_exec()
arguments to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
CPUArchState is no longer needed.
Prepares for changing qemu_kvm_init_cpu_signals() argument to CPUState.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It no longer depends on CPUArchState, so move it to qom/cpu.c.
Prepares for changing GDBState::c_cpu to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Change Monitor::mon_cpu to CPUState as well.
Reviewed-by: liguang <lig.fnst@cn.fujitsu.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It no longer relies on CPUArchState since 20d695a.
Reviewed-by: liguang <lig.fnst@cn.fujitsu.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
A few targets already managed to implement cpu_save() and cpu_load()
without defining CPU_SAVE_VERSION that causes them to be registered.
Guard the prototypes with CPU_SAVE_VERSION to avoid this happening again
until all targets are converted to VMState (or QIDL).
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
To be used to embed common CPU state into CPU subclasses.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It's the equivalent to cpu_class_set_vmsd(), to assign
DeviceClass::vmsd. It wasn't needed before since only static,
unmigratable VMStateDescriptions were assigned so far.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It's CPUClass::vmsd, not CPUState::vmsd.
Reviewed-by: liguang <lig.fnst@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
backup_start() creates a block job that copies a point-in-time snapshot
of a block device to a target block device.
We call backup_do_cow() for each write during backup. That function
reads the original data from the block device before it gets
overwritten. The data is then written to the target device.
Currently backup cluster size is hardcoded to 65536 bytes.
[I made a number of changes to Dietmar's original patch and folded them
in to make code review easy. Here is the full list:
* Drop BackupDumpFunc interface in favor of a target block device
* Detect zero clusters with buffer_is_zero() and use bdrv_co_write_zeroes()
* Use 0 delay instead of 1us, like other block jobs
* Unify creation/start functions into backup_start()
* Simplify cleanup, free bitmap in backup_run() instead of cb
* function
* Use HBitmap to avoid duplicating bitmap code
* Use bdrv_getlength() instead of accessing ->total_sectors
* directly
* Delete the backup.h header file, it is no longer necessary
* Move ./backup.c to block/backup.c
* Remove #ifdefed out code
* Coding style and whitespace cleanups
* Use bdrv_add_before_write_notifier() instead of blockjob-specific hooks
* Keep our own in-flight CowRequest list instead of using block.c
tracked requests. This means a little code duplication but is much
simpler than trying to share the tracked requests list and use the
backup block size.
* Add on_source_error and on_target_error error handling.
* Use trace events instead of DPRINTF()
-- stefanha]
Signed-off-by: Dietmar Maurer <dietmar@proxmox.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_add_before_write_notifier() function installs a callback that
is invoked before a write request is processed. This will be used to
implement copy-on-write point-in-time snapshots where we need to copy
out old data before overwriting it.
Note that BdrvTrackedRequest is moved to block_int.h since it is passed
to .notify() functions.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
notifier_list_notify() has no return value. This is fine when we just
want to invoke side-effects.
Sometimes it's useful for notifiers to produce a return value. This
allows notifiers to "veto" an operation and will be used by the block
layer before-write notifier.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This capability allows you to disable dynamic chunk registration
for better throughput on high-performance links.
For example, using an 8GB RAM virtual machine with all 8GB of memory in
active use and the VM itself is completely idle using a 40 gbps infiniband link:
1. x-rdma-pin-all disabled total time: approximately 7.5 seconds @ 9.5 Gbps
2. x-rdma-pin-all enabled total time: approximately 4 seconds @ 26 Gbps
These numbers would of course scale up to whatever size virtual machine
you have to migrate using RDMA.
Enabling this feature does *not* have any measurable affect on
migration *downtime*. This is because, without this feature, all of the
memory will have already been registered already in advance during
the bulk round and does not need to be re-registered during the successive
iteration rounds.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
These are the prototypes and implementation of new hooks that
RDMA takes advantage of to perform dynamic page registration.
An optional hook is also introduced for a custom function
to be able to override the default save_page function.
Also included are the prototypes and accessor methods used by
arch_init.c which invoke funtions inside savevm.c to call out
to the hooks that may or may not have been overridden
inside of QEMUFileOps.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This is used during RDMA initialization in order to
transmit a description of all the RAM blocks to the
peer for later dynamic chunk registration purposes.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
RDMA uses this to flush the control channel before sending its
own message to handle page registrations.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
QEMUFileRDMA also has read and write modes. This function is now
shared to reduce code duplication.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This exposes throughput (in megabits/sec) through QMP.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The RDMA event channel can be made non-blocking just like a TCP
socket. Exporting this function allows us to yield so that the
QEMU monitor remains available.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
RDMA writes happen asynchronously, and thus the performance accounting
also needs to be able to occur asynchronously. This allows anybody
to call into savevm.c to update both f->pos as well as into arch_init.c
to update the acct_info structure with up-to-date values when
the RDMA transfer actually completes.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Tested-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This reverts commit 9f24a8030a.
The start of the PCI hole is actually set to 0xf0000000 by hvmloader.
In order to retain ABI compatibility with Xen we leave the start of the
PCI hole at 0xf0000000 in QEMU (for Xen) too.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
# By Andreas Färber (3) and others
# Via Gerd Hoffmann
* kraxel/usb.84:
usb: fix serial number for hid devices
usb: add serial bus property
usb-host-libusb: set USB_DEV_FLAG_IS_HOST
usb/host-libusb: Fix building with libusb git master code
usb/hcd-ehci: Add Faraday FUSBH200 support
usb/hcd-ehci: Replace PORTSC macros with variables
usb/hcd-ehci: Add Tegra2 SysBus EHCI device
usb/hcd-ehci: Split off instance_init from realize
usb/hcd-ehci-sysbus: Convert to QOM realize
This patch adds a serial property for all usb devices, which can be
used to set the serial number of a usb device (as listed by lsusb -v)
to a specific value. Applies to emulated devices only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some arguments to these functions are booleans - either by declaration,
or by actual usage, but sometimes value of 0 or 1 is passed for a bool,
and sometimes it is declared as int but a bool value, or true/false,
is passed to it instead. Clean it up a bit.
Cc: liguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Using macros instead of static functions for dolog and for ldebug
simplifies the code and can also reduce the total code size.
GCC_ATTR was only used in audio_int.h, so it is now unused and
the definition can be removed from compiler.h.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The "info mtree" command in QEMU console prints only "memory" and "I/O"
address spaces while there are actually a lot more other AddressSpace
structs created by PCI and VIO devices. Those devices do not normally
have names and therefore not present in "info mtree" output.
The patch fixes this.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The DMAContext is a simple pointer to an AddressSpace that is now always
already available. Make everyone hold the address space directly,
and clean up the DMA API to use the AddressSpace directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fetch the root region from the sPAPRTCETable, and use it to build
an AddressSpace and DMAContext.
Now, everywhere we have a DMAContext we also have access to the
corresponding AddressSpace (either because we create it just before
the DMAContext, or because dma_context_memory's AddressSpace is
trivially address_space_memory).
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the new iommu support in the memory core for iommu support. The only
user, spapr, is also converted, but it still provides a DMAContext
interface until the non-PCI bits switch to AddressSpace.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
[ Do not calls memory_region_del_subregion() on the device's
bus_master_enable_region, it is an alias; return an AddressSpace
from the IOMMU hook and remove the destructor hook. - David Gibson ]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The translate function in the DMAContext is now always NULL.
Remove every reference to it.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we can stop using a "translating" DMAContext, but we do not yet modify
the sPAPRTCETable users to get an AddressSpace; they keep using the table
via a DMAContext.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TCE table is currently returned as a DMAContext, and non-type-safe
APIs are called later passing back the DMAContext. Since we want to move
away from DMAContext, use an opaque type instead, and add an accessor
to retrieve the DMAContext from it.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds a NotifierList to MemoryRegions which represent IOMMUs
allowing other parts of the code to register interest in mappings or
unmappings from the IOMMU. All IOMMU implementations will need to call
memory_region_notify_iommu() to inform those waiting on the notifier list,
whenever an IOMMU mapping is made or removed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new memory region type that translates addresses it is given,
then forwards them to a target address space. This is similar to
an alias, except that the mapping is more flexible than a linear
translation and trucation, and also less efficient since the
translation happens at runtime.
The implementation uses an AddressSpace mapping the target region to
avoid hierarchical dispatch all the way to the resolved region; only
iommu regions are looked up dynamically.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
[Modified to put translation in address_space_translate; assume
IOMMUs are not reachable from TCG. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So far, the size of all regions passed to listeners could fit in 64 bits,
because artificial regions (containers and aliases) are eliminated by
the memory core, leaving only device regions which have reasonable sizes
An IOMMU however cannot be eliminated by the memory core, and may have
an artificial size, hence we may need 65 bits to represent its size.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only address_space_translate_for_iotlb needs to return the section.
Every caller of address_space_translate now uses only section->mr,
return it directly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Except for the case of setting the IOTLB entry in TCG mode, we can avoid
the subpage dispatching handlers and do the resolution directly on
address_space_lookup_region. An IOTLB entry describes a full page, not
only the region that the first access to a sub-divided page may return.
This patch therefore introduces a special translation function,
address_space_translate_for_iotlb, that avoids the subpage resolutions.
In contrast, callers of the existing address_space_translate service
will now always receive the terminal memory region section. This will be
important for breaking the BQL and for enabling unaligned memory region.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1371208516-7857-5-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1371208516-7857-3-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Luiz Capitulino
# Via Luiz Capitulino
* luiz/queue/qmp:
qerror: drop QERR_OPEN_FILE_FAILED macro
block: bdrv_reopen_prepare(): don't use QERR_OPEN_FILE_FAILED
savevm: qmp_xen_save_devices_state(): use error_setg_file_open()
dump: qmp_dump_guest_memory(): use error_setg_file_open()
cpus: use error_setg_file_open()
blockdev: use error_setg_file_open()
block: mirror_complete(): use error_setg_file_open()
rng-random: use error_setg_file_open()
error: add error_setg_file_open() helper
Message-id: 1371484631-29510-1-git-send-email-lcapitulino@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Initial commit for emulated Non-Volatile-Memory Express (NVMe) pci
storage device.
NVMe is an open, industry driven storage specification defining
an optimized register and command set designed to deliver the full
capabilities of non-volatile memory on PCIe SSDs. Further information
may be found on the organizations website at:
http://www.nvmexpress.org/
This commit implements the minimum from the specification to work with
existing drivers.
Cc: Keith Busch <keith.busch@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
# By Paolo Bonzini (4) and others
# Via Peter Maydell
* pmaydell/configury.next:
ppc: Remove CONFIG_FDT conditionals
microblaze: Remove CONFIG_FDT conditionals
arm: Remove CONFIG_FDT conditionals
configure: Require libfdt for arm, ppc, microblaze softmmu targets
configure: dtc: Probe for libfdt_env.h
build: drop TARGET_TYPE
main: use TARGET_ARCH only for the target-specific #define
build: do not use TARGET_ARCH
build: rename TARGET_ARCH2 to TARGET_NAME
Add a stp file for usage from build directory
Message-id: 1371221594-11556-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* 'realize-isa.v2' of git://github.com/afaerber/qemu-cpu:
qdev: Drop FROM_QBUS() macro
isa: QOM'ify ISADevice
isa: QOM'ify ISABus
i8259: Convert PICCommonState to use QOM realizefn
kvm/i8259: QOM'ify some more
i8259: QOM'ify some more
i8254: Convert PITCommonState to QOM realizefn
kvm/i8254: QOM'ify some more
i8254: QOM'ify some more
isa: Use realizefn for ISADevice
cs4231a: QOM'ify some more
gus: QOM'ify some more
Currently QEMU provides a local clone of the file libfdt_env.h in
/include. This file is supposed to come with the libfdt package and is
only needed for broken installs of libfdt. Now that we have submodule
dtc, just ignore these broken installs and prompt for the dtc submodule
install instead. QEMU's local libfdt_env.h is removed accordingly.
Manifests as a bug when building QEMU with modern libfdt. The new
version of libfdt does not compile when QEMUs libfdt_env.h takes
precedence over the hosts.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 9b6a3a52e3f46cfbc1ded9ab56385ec045e46705.1369628289.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Having size precede the associated pointer is odd. Swap them, and fix
up the types.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo "ever the optimist" Ersek <lersek@redhat.com>
Message-id: 1370610036-10577-5-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
<stdio.h> has always been missing. Rest missed in commit eeacee4.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo "ever the optimist" Ersek <lersek@redhat.com>
Message-id: 1370610036-10577-3-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Michael Tokarev (4) and others
# Via Michael Tokarev
* mjt/trivial-patches-next: (26 commits)
piix: fix some printf errors when debug is enabled
cputlb: fix debug logs
create qemu_openpty_raw() helper function and move it to a separate file
main-loop: do not include slirp/slirp.h, use libslirp.h instead
libcacard/vscclient: fix leakage of socket on error paths
linux-headers: Update to v3.10-rc5
KVM: PPC: Add dummy kvm_arch_init_irq_routing()
KVM: S390: Add dummy kvm_arch_init_irq_routing()
KVM: ARM: Add dummy kvm_arch_init_irq_routing()
ivshmem: add missing error exit(2)
hw/xen: Use g_free instead of free and fix potential memory leaks
target-sparc: Replace free by g_free
hw/scsi: Don't increment a boolean value
device tree: Fix cppcheck warning
Makefile: Install qemu-img and qemu-nbd man pages only if built
Unbreak -no-quit for GTK, validate SDL options
gtk: implement -full-screen
char/serial: serial_ioport_write: Factor out common code
char/serial: Use generic Fifo8
char/serial: cosmetic fixes.
...
Message-id: 1371207042-17980-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Andreas Färber (12) and others
# Via Andreas Färber
* afaerber/qom-cpu:
spapr_rtas: Abstract rtas_start_cpu() with qemu_get_cpu()
spapr_rtas: Abstract rtas_query_cpu_stopped_state() with qemu_get_cpu()
memory_mapping: Improve qemu_get_guest_memory_mapping() error reporting
dump: Abstract dump_init() with cpu_synchronize_all_states()
cpu: Change default for CPUClass::get_paging_enabled()
dump: Drop qmp_dump_guest_memory() stub and build for all targets
memory_mapping: Drop qemu_get_memory_mapping() stub
cpu: Turn cpu_get_memory_mapping() into a CPUState hook
memory_mapping: Move MemoryMappingList typedef to qemu/typedefs.h
cpu: Turn cpu_paging_enabled() into a CPUState hook
monitor: Simplify do_inject_mce() with qemu_get_cpu()
target-i386: cpu: Fix potential buffer overrun in get_register_name_32()
target-i386: Set level=4 on Conroe/Penryn/Nehalem
target-i386: Update model values on Conroe/Penryn/Nehalem CPU models
pc: Create pc-*-1.6 machine-types
pc: Fix crash when attempting to hotplug CPU with negative ID
dump: Move stubs into libqemustub.a
# By Claudio Fontana (9) and others
# Via Peter Maydell
* pmaydell/tcg-aarch64.next:
MAINTAINERS: add tcg/aarch64 maintainer
configure: permit compilation on arm aarch64
tcg/aarch64: implement user mode qemu ld/st
user-exec.c: aarch64 initial implementation of cpu_signal_handler
tcg/aarch64: implement sign/zero extend operations
tcg/aarch64: implement byte swap operations
tcg/aarch64: implement AND/TEST immediate pattern
tcg/aarch64: improve arith shifted regs operations
tcg/aarch64: implement new TCG target for aarch64
include/elf.h: add aarch64 ELF machine and relocs
configure: Drop CONFIG_ATFILE test
linux-user: Drop direct use of openat etc syscalls
linux-user: Allow getdents to be provided by getdents64
Message-id: 1371052645-9006-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-for-anthony:
tcg: Remove redundant tcg_target_init checks
tcg: Use QEMU_BUILD_BUG_ON for CPU_TLB_ENTRY_BITS
Message-id: 1370437167-11278-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In two places qemu uses openpty() which is very system-dependent,
and in both places the pty is switched to raw mode as well.
Make a wrapper function which does both steps, and move all the
system-dependent complexity into a separate file, together
with static/local implementations of openpty() and cfmakeraw()
from qemu-char.c.
It is in a separate file, not part of oslib-posix.c, because
openpty() often resides in -lutil which is not linked to
every program qemu builds.
This change removes #including of <pty.h>, <termios.h>
and other rather specific system headers out of qemu-common.h,
which isn't a place for such specific headers really.
This version has been verified to build correctly on Linux,
OpenBSD, FreeBSD and OpenIndiana. On the latter it lets qemu
to be built with gtk gui which were not possible there due to
missing openpty() and cfmakeraw().
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Tested-by: Andreas Färber <andreas.faerber@web.de>
add preliminary support for TCG target aarch64.
Signed-off-by: Claudio Fontana <claudio.fontana@huawei.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 51A5C596.3090108@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
we will use the 26bit relative relocs in the aarch64 tcg target.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Claudio Fontana <claudio.fontana@huawei.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 51A5C52A.4080001@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Aiming for GTK as replacement for SDL, a feature like -full-screen should also
be implemented.
Bringing the window into full-screen mode is done by activating the "Fullscreen"
menu item. This is done after showing the windows to make the cursor and menu
hidden.
v2: drop -no-frame implementation, use booleans instead of ints and ensure
consistency between ui state and menu.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use the generic Fifo8 helper provided by QEMU, rather than re-implement
privately.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Pass any Error out into dump_init() and have it actually stop on errors.
Whether it is unsupported on a certain CPU can be checked by looking for
a NULL CPUClass::get_memory_mapping field.
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
[AF: Reverted changes to CPU loops]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This will avoid issues with hwaddr and ram_addr_t when including
sysemu/memory_mapping.h for CONFIG_USER_ONLY, e.g., from qom/cpu.h.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Relocate assignment of x86 get_arch_id to have all hooks in one place.
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The CPUID level value on Conroe, Penryn, and Nehalem are too low. This
causes at least one known problem: the -smp "threads" option doesn't
work as expect if level is < 4, because thread count information is
provided to the guest on CPUID[EAX=4,ECX=2].EAX
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The CPUID model values on Conroe, Penryn, and Nehalem are too
conservative and don't reflect the values found on real Conroe, Penryn,
and Nehalem CPUs.
This causes at least one known problems: Windows XP disables sysenter
when (family == 6 && model <= 2), but Skype tries to use the sysenter
instruction anyway because it is reported as available on CPUID, making
it crash.
This patch sets appropriate model values that correspond to real Conroe,
Penryn, and Nehalem CPUs.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
When CHR_EVENT_OPENED was initially added, it was CHR_EVENT_RESET,
and it was issued as a bottom-half:
86e94dea5b
Which we basically used to print out a greeting/prompt for the
monitor.
AFAICT the only reason this was ever done in a BH was because in
some cases we'd modify the chr_write handler for a new chardev
backend *after* the site where we issued the reset (see:
86e94d:qemu_chr_open_stdio())
At some point this event was renamed to CHR_EVENT_OPENED, and we've
maintained the use of this BH ever since.
However, due to 9f939df955, we schedule
the BH via g_idle_add(), which is causing events to sometimes be
delivered after we've already begun processing data from backends,
leading to:
known bugs:
QMP:
session negotation resets with OPENED event, in some cases this
is causing new sessions to get sporadically reset
potential bugs:
hw/usb/redirect.c:
can_read handler checks for dev->parser != NULL, which may be
true if CLOSED BH has not been executed yet. In the past, OPENED
quiesced outstanding CLOSED events prior to us reading client
data. If it's delayed, our check may allow reads to occur even
though we haven't processed the OPENED event yet, and when we
do finally get the OPENED event, our state may get reset.
qtest.c:
can begin session before OPENED event is processed, leading to
a spurious reset of the system and irq_levels
gdbstub.c:
may start a gdb session prior to the machine being paused
To fix these, let's just drop the BH.
Since the initial reasoning for using it still applies to an extent,
work around that by deferring the delivery of CHR_EVENT_OPENED until
after the chardevs have been fully initialized, toward the end of
qmp_chardev_add() (or some cases, qemu_chr_new_from_opts()). This
defers delivery long enough that we can be assured a CharDriverState
is fully initialized before CHR_EVENT_OPENED is sent.
Also, rather than requiring each chardev to do an explicit open, do it
automatically, and allow the small few who don't desire such behavior to
suppress the OPENED-on-init behavior by setting a 'explicit_be_open'
flag.
We additionally add missing OPENED events for stdio backends on w32,
which were previously not being issued, causing us to not recieve the
banner and initial prompts for qmp/hmp.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-id: 1370636393-21044-1-git-send-email-mdroth@linux.vnet.ibm.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
