Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.
Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
"Setting the PAGE to FFh means that all subsequent comands are to be
applied to all outputs.
Some commands, such as READ_TEMPERATURE, may use a common sensor but
be available on all pages of a device. Such implementations are the
decision of each device manufacturer or are specified in a PMBus
Application Profile. Consult the manufacturer's documents or the
Application Profile Specification as needed."
For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a 'stop' string seems more appropriate than 'normal'.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no 'slave match interrupt' enable bit in the Interrupt
Control Register. Consider it is always enabled and extend the mask
value 'bus->regs[intr_ctrl_reg]' with the SLAVE_ADDR_RX_MATCH bit when
the interrupt is raised.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Build a single string instead of having several parameters on the trace
event.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: simplified trace buffer creation ]
Message-Id: <20220601210831.67259-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleans up some of the field accessing, setting, and clearing
bitwise operations, and wraps them in macros instead.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I33018d6325fa04376e7c29dc4a49ab389a8e333a
Message-Id: <20220331043248.2237838-4-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
wire AcpiDevAmlIf interface to build ich9-smb and its slave
devices AML. It will be used by followup patches to switch
from creating AML in ad-hoc way to a more systematic one
that will scan present devices and ask them to provide
their AML code like it's done with ISA devices.
This patch is a partial conversion, as it only fetches
AML from slave devices attached to its I2C bus.
The conversion will be completed when PCI bus is
switched to use AcpiDevAmlIf and build_smb0() could be
dropped.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-16-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
This change cleans up the inputs to pmbus_receive uint, the length of
received data is contained in PMBusDevice state and doesn't need to be
passed around.
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- add the VOUT_MIN and STATUS_MFR registers
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously this device created N subdevices which each owned an i2c bus.
Now this device simply owns the N i2c busses directly.
Tested: Verified devices behind mux are still accessible via qmp and i2c
from within an arm32 SoC.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220202164533.1283668-1-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
imply I2C_DEVICES
to cause those pluggable devices to be built.
In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-2-peter.maydell@linaro.org
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
Add the differential clock input feature bit to the generated SPD
data. Most guests don't seem to care but pegasos2 firmware version 1.2
checks for this bit and stops with unsupported module type error if
it's not present. Since this feature is likely present on real memory
modules add it in the general code rather than patching the generated
SPD data in pegasos2 board only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <19d42ade295d5297aa624a9eb757b8df18cf64d6.1626367844.git.balaton@eik.bme.hu>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.
Use these new helpers in the SMBus / AUX bus models.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To allow further simplications, extract i2c_do_start_transfer()
from i2c_start_transfer(). This is mostly the same function,
but the former is static and takes an enum argument.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It took me a while to find this model datasheet, since it is
an OCR scan. Add a reference to save other developers time.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
-----BEGIN PGP SIGNATURE-----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=IamZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-v1' into staging
Add a bus multiplexer device
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
# gpg: Signature made Thu 13 May 2021 22:48:07 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-v1:
hw/i2c: add pca954x i2c-mux switch
hw/i2c: move search to i2c_scan_bus method
hw/i2c: add match method for device search
hw/i2c: name I2CNode list in I2CBus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmCPtbASHGxhdXJlbnRA
dml2aWVyLmV1AAoJEPMMOL0/L748I3wP/Al7yi77BMpts1t3lGMm7EBjKgkppnpr
wZYEM68bJonvvGiEKQjexn1CUfnDcq7f5SZkzcUNLI4oP57pyywb4/gshN0k/Zz8
uCDveMfnhbio2sqlXiMsH9TOhcv/4wtXAek/ghP7EOjkBvyXrAFIQ7eEPEB9cp+X
xxs9DxqfWmrGB6vt7Er78zjfUETSMa+UrheVLwbRMhJcc0Bg8hT2DCn9Lw6IjfOy
usWdrLTGc6qg1zdZzi8QR7jZ+bNx0h+aJLlm8M4cVitXq9v2wb3+6KdsOAeYioAE
AsnClw0m8j/xtMh3g4/hB4oCxMj0jRdZ9GIGs8Didw5ZwkXTRvFM1GK1PHxqX4pF
8xMW6Qq0bSUr4II6bPOukBUMUAnPYdkh+iHXsYSZG0I3u6VZLgMK3AXmKRukAYqe
kQ1lcRe3Lwsp2h+jMBBsbCWhwYdA3THFO4YO31cUaZ191A7z57905QMbqJG/H3HB
7IUBYBNbrhgysPsNBvY6Lr7yUJIocMgcfP36UHYcBPsDdZgjNCQZneJlkaRlQb8+
CtUSF8D614EguzGsWaIn3uBSm9THKKLd1rSXCyTSgrXDI285mXlKmEWZvm236ew0
OEmIz/Ach/R4268j76enYGa1aubsxnrphUfC3aePu0Wzd3QW4RxnCSq7wc4ARPw7
WTL7J00P578h
=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The RAM memory region is now used for DMAs accesses instead of the
memory address space region. Mask off the top bits of the DMA address
to reflect this change.
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The STATUS register will be reset to IDLE in
cnpcm7xx_smbus_enter_reset(), no need to preset
it in instance_init().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210228224813.312532-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
VMStateDescription.fields should be end with VMSTATE_END_OF_LIST().
However, microbit_i2c_vmstate doesn't follow it. Let's change it.
Fixes: 9d68bf564e ("arm: Stub out NRF51 TWI magnetometer/accelerometer detection")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201019093401.2993833-1-liangpeng10@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The System Management Bus is more or less a derivative of the I2C
bus, thus the Kconfig entry depends of I2C.
Not all boards providing an I2C bus support SMBus.
Use two different Kconfig entries to be able to select I2C without
selecting SMBus.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-6-philmd@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Extract i2c_try_create_slave() and i2c_realize_and_unref()
from i2c_create_slave().
We can now set properties on a I2CSlave before it is realized.
This is in line with the recent qdev/QOM changes merged
in commit 6675a653d2.
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072723.6324-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'ARM SBCon two-wire serial bus interface' is the official
name describing the pair of registers used to bitbanging
I2C in the Versatile boards.
Make the private VersatileI2CState structure as public
ArmSbconI2CState.
Add the TYPE_ARM_SBCON_I2C, alias to our current
TYPE_VERSATILE_I2C model.
Rename the memory region description as 'arm_sbcon_i2c'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use self-explicit definitions instead of magic values.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use self-explicit definitions instead of magic values.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The DEVICE() macro is defined as:
#define DEVICE(obj) OBJECT_CHECK(DeviceState, (obj), TYPE_DEVICE)
which expands to:
((DeviceState *)object_dynamic_cast_assert((Object *)(obj), (name),
__FILE__, __LINE__,
__func__))
This assertion can only fail when @obj points to something other
than its stated type, i.e. when we're in undefined behavior country.
Remove the unnecessary DEVICE() casts when we already know the
pointer is of DeviceState type.
Patch created mechanically using spatch with this script:
@@
typedef DeviceState;
DeviceState *s;
@@
- DEVICE(s)
+ s
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-4-f4bug@amsat.org>
On the NRF51 series, all peripherals have a fixed I/O size
of 4KiB. Define NRF51_PERIPHERAL_SIZE and use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix warning reported by Clang static code analyzer:
CC hw/i2c/pm_smbus.o
hw/i2c/pm_smbus.c:187:17: warning: Value stored to 'ret' is never read
ret = 0;
^ ~
Reported-by: Clang Static Analyzer
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200422133152.16770-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
spd_data_generate() splits @ram_size bytes into @nbanks RAM banks of
1 << sz_log2 MiB each, like this:
size = ram_size >> 20; /* work in terms of megabytes */
[...]
nbanks = 1;
while (sz_log2 > max_log2 && nbanks < 8) {
sz_log2--;
nbanks++;
}
Each iteration halves the size of a bank, and increments the number of
banks. Wrong: it should double the number of banks.
The bug goes back all the way to commit b296b664ab "smbus: Add a
helper to generate SPD EEPROM data".
It can't bite because spd_data_generate()'s current users pass only
@ram_size that result in *zero* iterations:
machine RAM size #banks type bank size
fulong2e 256 MiB 1 DDR 256 MiB
sam460ex 2048 MiB 1 DDR2 2048 MiB
1024 MiB 1 DDR2 1024 MiB
512 MiB 1 DDR2 512 MiB
256 MiB 1 DDR2 256 MiB
128 MiB 1 SDR 128 MiB
64 MiB 1 SDR 64 MiB
32 MiB 1 SDR 32 MiB
Apply the obvious, minimal fix. I admit I'm tempted to rip out the
unused (and obviously untested) feature instead, because YAGNI.
Note that this is not the final result, as spd_data_generate() next
increases #banks from 1 to 2 if possible. This is done "to avoid a
bug in MIPS Malta firmware". We don't even use this function with
machine type malta. *Shrug*
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422134815.1584-5-armbru@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
spd_data_generate() can pass @errp to error_setg() more than once when
it adjusts both memory size and type. Harmless, because no caller
passes anything that needs adjusting. Until the previous commit,
sam460ex passed types that needed adjusting, but not sizes.
spd_data_generate()'s contract is rather awkward:
If everything's fine, return non-null and don't set an error.
Else, if memory size or type need adjusting, return non-null and
set an error describing the adjustment.
Else, return null and set an error reporting why no data can be
generated.
Its callers treat the error as a warning even when null is returned.
They don't create the "smbus-eeprom" device then. Suspicious.
Since the previous commit, only "everything's fine" can actually
happen. Drop the unused code and simplify the callers. This gets rid
of the error API violation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422134815.1584-3-armbru@redhat.com>
hw/i2c/smbus_ich9.c calls range_covers_byte(). Include "qemu/range.h"
which declares it.
This fixes (when modifying unrelated headers):
hw/i2c/smbus_ich9.c:66:9: error: implicit declaration of function 'range_covers_byte' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (range_covers_byte(address, len, ICH9_SMB_HOSTC)) {
^
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-14-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Instead, set the initial data field directly.
(the initial data is an array of 256 bytes. As I don't know if it may
change over time, I keep the pointer to original buffer as is, but it
might be worth to consider to copy it instead)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the AST2400 and AST2500 SoCs have one IRQ shared
by all I2C busses. The AST2600 SoC I2C controller has one IRQ per bus
and 16 busses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for register differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-16-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Currently the bitbang_i2c_init() function allocates a
bitbang_i2c_interface struct which it returns. This is unfortunate
because it means that if the function is used from a DeviceState
init method then the memory will be leaked by an "init then delete"
cycle, as used by the qmp/hmp commands that list device properties.
Since three out of four of the uses of this function are in
device init methods, switch the function to do an in-place
initialization of a struct that can be embedded in the
device state struct of the caller.
This fixes LeakSanitizer leak warnings that have appeared in the
patchew configuration (which only tries to run the sanitizers
for the x86_64-softmmu target) now that we use the bitbang-i2c
code in an x86-64 config.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190702163844.20458-1-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bitbang i2c implementation is also useful for other device models
such as DDC in display controllers. Move the header to include/hw/i2c/
to allow it to be used from other device models and adjust users of
this include. This also reverts commit 2b4c1125ac which is no longer
needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 5d1fe4db846ab9be4b77ddb0d43cc74cd200a003.1561028123.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The license information in this file is rather confusing. The text
declares LGPL first, but then says that contributions after Jan 2012
are licensed under the GPL instead. How should the average user who
just downloaded the release tarball know which part is now GPL and
which is LGPL? Also, as far as I can see, the file has been added to
QEMU *after* January in 2012, so the whole file should be GPL by
default instead.
Furthermore, looking at the text of the LGPL (see COPYING.LIB in the
top directory), the license clearly states in section "3." that one
should rather replace the license information in such a case instead.
Thus let's clean up the confusing statements and use the proper GPL
text only.
Message-Id: <1549471435-21887-1-git-send-email-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Move it together with the other EDID code. hw/i2c should only
include the core and the adapters, not the slaves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190325155923.30987-1-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Original commit message:
This patch adds an emulation model for i2c controller found on most of the FSL SoCs.
It also integrates the RTC (ds1338) that sits on the i2c Bus with e500 machine model.
Patch was originally written by Amit Singh Tomar <amit.tomar@freescale.com>
see http://patchwork.ozlabs.org/patch/431475/
I only fixed it enough for application on top of current qemu master
20b084c4b1, and hopefully fixed checkpatch errors
Tested by booting Linux kernel 4.20.12. Now e500 machine doesn't need
network time protocol daemon because it will have working RTC
(before all timestamps on files were from 2016)
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Signed-off-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190306102812.28972-1-randrianasulu@gmail.com>
[dwg: Add Kconfig stanza to define the new symbol, update MAINTAINERS]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reset the contents to init data and reset the offset on a machine
reset.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Transfer the state of the EEPROM on a migration. This way the
data remains consistent on migration.
This required moving the actual data to a separate array and
using the data provided in the init function as a separate
initialization array, since a pointer property has to be a
void * and the array needs to be uint8_t[].
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It was hard-coded to 256 in a number of places, create a constant
for that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Create a type name and a cast macro and use those through the
code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
