Don't use cpu_to_*w() and *_to_cpup() to do byte-swapped loads
and stores; instead use ld*_p() and st*_p() which correctly handle
misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-2-git-send-email-peter.maydell@linaro.org
The Cadence GEM data sheet says:
"Wrap - marks last descriptor in transmit buffer descriptor list. This
can be set for any buffer within the frame."
which seems to imply that when the wrap bit is set so is the last bit.
Previously if the wrap bit is set, but the last is not then QEMU will
enter an infinite loop.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: eb23f15c67989ea6a53609dc66568399dadf52a7.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A guest can write zero to the DMACFG resulting in an infinite loop when
it reaches the while(bytes_to_copy) loop.
To avoid this issue enforce a minimum size for the RX buffer. Hardware
does not have this enforcement and relies on the guest to set a non-zero
value.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: 84bb1c391b833275da3f573d4972920cea34c188.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/net/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-11-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Beginning of reconnect support for vhost-user.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXY0Q3AAoJECgfDbjSjVRpkVcH/2gTHRE9yUoWe6ROvPV67BKx
8Iy9GzJ3BMO3RolVZEA5KXIevn5TG+pV274BZEuXMD3AL/molv279p0o/gvBYoqq
V0jNH2MO+MV6D9OzhUXcgWSejvybF5W07ojPDU/hlgtFXPZFbJDyt95MWaLiilOg
cCtTuRqgrrRaypcnnk/CIDbC+Ek2kAYdgQHQbfj9ihle3TWO8R0bSXnFqSaqCIkM
4slMlv8y82fODeiO83nkpfAP1NCnfnRC8r8Gv7hbEUTlZQntavx5DuYdiIx6nsJE
W0g+Gpe1o0+jRuMnucGIUZvqzZ0e/I0wZuV16Nsfx+Rbd5+4CzTxZda5Qb05v7I=
=BHbJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
Beginning of reconnect support for vhost-user.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 17 Jun 2016 01:28:39 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
MAINTAINERS: add Marcel to PCI
msi_init: change return value to 0 on success
fix some coding style problems
pci core: assert ENOSPC when add capability
test: start vhost-user reconnect test
tests: append i386 tests
vhost-net: save & restore vring enable state
vhost-net: save & restore vhost-user acked features
vhost-net: do not crash if backend is not present
vhost-user: disconnect on start failure
qemu-char: add qemu_chr_disconnect to close a fd accepted by listen fd
tests/vhost-user-bridge: workaround stale vring base
tests/vhost-user-bridge: add client mode
vhost-user: add ability to know vhost-user backend disconnection
pci: fix pci_requester_id()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
tests/Makefile.include
It has:
1. More newlines make the code block well separated.
2. Add more comments for msi_init.
3. Fix a indentation in vmxnet3.c.
4. ioh3420 & xio3130_downstream: put PCI Express capability init function
together, make it more readable.
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A driver may change the vring enable state at run time but vhost-user
backend may not be present (a contrived example is when the backend is
disconnected and the device is reconfigured after driver rebinding)
Restore the vring state when the vhost-user backend is started, so it
can process the ring.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The initial vhost-user connection sets the features to be negotiated
with the driver. Renegotiation isn't possible without device reset.
To handle reconnection of vhost-user backend, ensure the same set of
features are provided, and reuse already acked features.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Do not crash when backend is not present while enabling the ring. A
following patch will save the enabled state so it can be restored once
the backend is started.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since mit_delay can never be 0 this if statement is
superfluous.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This patch fixes used-uninitialized false
positive while compiling with ust tracing
backend plus gcc 4.6.3:
hw/net/e1000e.c: In function ‘e1000e_io_write’:
hw/net/e1000e.c:170:39: error: ‘idx’ may be used uninitialized in this function [-Werror=uninitialized]
hw/net/e1000e.c: In function ‘e1000e_io_read’:
hw/net/e1000e.c:145:35: error: ‘idx’ may be used uninitialized in this function [-Werror=uninitialized]
cc1: all warnings being treated as errors
make: *** [hw/net/e1000e.o] Error 1
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-id: 1465023763-10773-1-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ust trace backend has limitation of maximum 10
arguments per event. Traces with more arguments
cannot be compiled for this backend.
Trace e1000e_rx_rss_ip6 introduced by previous
commits has 11 arguments and fails to compile with
ust trace backend.
This patch fixes the problem by splitting this
tracepoint into two successive tracepoints with
smaller number of arguments.
For more information see comment regarding TP_ARGS
in lttng/tracepoint.h:
/*
* TP_ARGS takes tuples of type, argument separated by a comma.
* It can take up to 10 tuples (which means that less than 10 tuples is
* fine too).
* Each tuple is also separated by a comma.
*/
Build log generated by this problem:
In file included from ./trace/generated-tracers.h:9:0,
from /home/travis/build/qemu/qemu/include/trace.h:4,
from util/oslib-posix.c:36:
./trace/generated-ust-provider.h:16556:3: error: unknown type name ‘_TP_EXPROTO_Bool’
In file included from /home/travis/build/qemu/qemu/include/trace.h:4:0,
from util/oslib-posix.c:36:
./trace/generated-tracers.h: In function ‘trace_e1000e_rx_rss_ip6’:
./trace/generated-tracers.h:8379:431: error: expected string literal before ‘_SDT_ASM_OPERANDS_ipv6_enabled’
./trace/generated-tracers.h:8379:431: error: implicit declaration of function ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=implicit-function-declaration]
./trace/generated-tracers.h:8379:431: error: nested extern declaration of ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=nested-externs]
cc1: all warnings being treated as errors
make: *** [util/oslib-posix.o] Error 1
make: *** Waiting for unfinished jobs....
In file included from ./trace/generated-tracers.h:9:0,
from /home/travis/build/qemu/qemu/include/trace.h:4,
from util/hbitmap.c:16:
./trace/generated-ust-provider.h:16556:3: error: unknown type name ‘_TP_EXPROTO_Bool’
In file included from /home/travis/build/qemu/qemu/include/trace.h:4:0,
from util/hbitmap.c:16:
./trace/generated-tracers.h: In function ‘trace_e1000e_rx_rss_ip6’:
./trace/generated-tracers.h:8379:431: error: expected string literal before ‘_SDT_ASM_OPERANDS_ipv6_enabled’
./trace/generated-tracers.h:8379:431: error: implicit declaration of function ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=implicit-function-declaration]
./trace/generated-tracers.h:8379:431: error: nested extern declaration of ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=nested-externs]
cc1: all warnings being treated as errors
make: *** [util/hbitmap.o] Error 1
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Message-id: 1464894748-27803-1-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJXT9DWAAoJEO8Ells5jWIRgFAH/1ZDXm8V523AMDOEvBAWgqur
Dj8ZaIwFkqJp7xtLdhS0yKF3xW+vtgx9k+Qftk0S8qEiFKPbThR8iB5VNuesErwd
AZhWo4bnVhKwtWyMw3BDRDK1N4huAWPMZEva1xovR/Cc9v5IG5mx57/K3Zz5C8ec
Jsn4DsLKN0q7W0D0dlnbEOkSjl6iKJchvfPCR6UfvrU7BxfXaCZ9Z7Sfh8ec6tfr
iMgcV9u3A3Zs72gTM9/jdKx8vOrWtdKJufJ8s2Bctc7CyfBNWwnV8PjndhEe3Xvs
vlYeJopdpDPsdMkMtYD6cevtEgvD5yhOBndJ7et807jjuCvUf837tMhodKkFk9M=
=SjIZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 02 Jun 2016 07:23:18 BST using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request: (31 commits)
Add ENET device to i.MX6 SOC.
Add ENET/Gbps Ethernet support to FEC device
i.MX: move FEC device to a register array structure.
i.MX: Rename i.MX FEC defines to ENET_XXX
i.MX: reset TX/RX descriptors when FEC is disabled.
i.MX: Fix FEC code for ECR register reset value.
i.MX: Fix FEC code for MDIO address selection
i.MX: Fix FEC code for MDIO operation selection
net: handle optional VLAN header in checksum computation.
net: improve UDP/TCP checksum computation.
e1000e: Introduce qtest for e1000e device
net: Introduce e1000e device emulation
e1000: Move out code that will be reused in e1000e
e1000_regs: Add definitions for Intel 82574-specific bits
vmxnet3: Use pci_dma_* API instead of cpu_physical_memory_*
net_pkt: Extend packet abstraction as required by e1000e functionality
rtl8139: Move more TCP definitions to common header
net_pkt: Name vmxnet3 packet abstractions more generic
vmxnet3: Use common MAC address tracing macros
net: Add macros for MAC address tracing
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ENET device (present in i.MX6) is "derived" from FEC and backward
compatible with it.
This patch adds the necessary support of the added feature in the ENET
device to allow Linux to use it (on supported processors).
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is to prepare for the ENET Gb device of the i.MX6.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual
RX adn TX descriptors are reseted when the FEC device is disabled through ECR.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual ECR register is
initialized at 0xf0000000 at reset time.
We fix the value.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual
When writing to MMFR register, the MDIO device and adress are selected by
bit 27 to 23 and bit 22 to 18 respectively. This is a total of 10 bits
that need to be used by the Phy chip/address decoding function.
This patch fixes the number of bits used from 9 to 10.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual
When writing the MMFR register, bit 29 and 28 select the requested operation.
* 10 means read operation with valid MII mgmt frame
* 11 means read operation with non compliant MII mgmt frame
* 01 means write operation with valid MII mgmt frame
* 00 means write operation with non compliant MII mgmt frame
So while bit 28 does change beween read/write for valid MII mgmt frame, the
mening is inverted for non compliant MII mgmt frame.
Bit 29 on the other hand means read/write whatever the type of mgmt frame
involved.
So this patch change the operation selection from bit 28 to bit 29 as it is
more generic.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch introduces emulation for the Intel 82574 adapter, AKA e1000e.
This implementation is derived from the e1000 emulation code, and
utilizes the TX/RX packet abstractions that were initially developed for
the vmxnet3 device. Although some parts of the introduced code may be
shared with e1000, the differences are substantial enough so that the
only shared resources for the two devices are the definitions in
hw/net/e1000_regs.h.
Similarly to vmxnet3, the new device uses virtio headers for task
offloads (for backends that support virtio extensions). Usage of
virtio headers may be forcibly disabled via a boolean device property
"vnet" (which is enabled by default). In such case task offloads
will be performed in software, in the same way it is done on
backends that do not support virtio headers.
The device code is split into two parts:
1. hw/net/e1000e.c: QEMU-specific code for a network device;
2. hw/net/e1000e_core.[hc]: Device emulation according to the spec.
The new device name is e1000e.
Intel specifications for the 82574 controller are available at:
http://www.intel.com/content/dam/doc/datasheet/82574l-gbe-controller-datasheet.pdf
Throughput measurement results (iperf2):
Fedora 22 guest, TCP, RX
4 ++------------------------------------------+
| |
| X X X X X
3.5 ++ X X X X |
| X |
| |
3 ++ |
G | X |
b | |
/ 2.5 ++ |
s | |
| |
2 ++ |
| |
| |
1.5 X+ |
| |
+ + + + + + + + + + + +
1 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, TCP, TX
18 ++-------------------------------------------+
| X |
16 ++ X X X X X
| X |
14 ++ |
| |
12 ++ |
G | X |
b 10 ++ |
/ | |
s 8 ++ |
| |
6 ++ X |
| |
4 ++ |
| X |
2 ++ X |
X + + + + + + + + + + +
0 ++--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, UDP, RX
3 ++------------------------------------------+
| X
| |
2.5 ++ |
| |
| |
2 ++ X |
G | |
b | |
/ 1.5 ++ |
s | X |
| |
1 ++ |
| |
| X |
0.5 ++ |
| X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Fedora 22 guest, UDP, TX
1 ++------------------------------------------+
| X
0.9 ++ |
| |
0.8 ++ |
0.7 ++ |
| |
G 0.6 ++ |
b | |
/ 0.5 ++ |
s | X |
0.4 ++ |
| |
0.3 ++ |
0.2 ++ X |
| |
0.1 ++ X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, TCP, RX
3.2 ++------------------------------------------+
| X |
3 ++ |
| |
2.8 ++ |
| |
2.6 ++ X |
G | X X X X X
b 2.4 ++ X X |
/ | |
s 2.2 ++ |
| |
2 ++ |
| X X |
1.8 ++ |
| |
1.6 X+ |
+ + + + + + + + + + + +
1.4 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, TCP, TX
14 ++-------------------------------------------+
| |
| X X
12 ++ |
| |
10 ++ |
| |
G | |
b 8 ++ |
/ | X |
s 6 ++ |
| |
| |
4 ++ X |
| |
2 ++ |
| X X X |
+ X X + + X X + + + + +
0 X+--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, UDP, RX
1.6 ++------------------------------------------X
| |
1.4 ++ |
| |
1.2 ++ |
| X |
| |
G 1 ++ |
b | |
/ 0.8 ++ |
s | |
0.6 ++ X |
| |
0.4 ++ |
| X |
| |
0.2 ++ X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, UDP, TX
0.6 ++------------------------------------------+
| X
| |
0.5 ++ |
| |
| |
0.4 ++ |
G | |
b | |
/ 0.3 ++ X |
s | |
| |
0.2 ++ |
| |
| X |
0.1 ++ |
| X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Code that will be shared moved to a separate files.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
To make this device and network packets
abstractions ready for IOMMU.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch extends the TX/RX packet abstractions with features that will
be used by the e1000e device implementation.
Changes are:
1. Support iovec lists for RX buffers
2. Deeper RX packets parsing
3. Loopback option for TX packets
4. Extended VLAN headers handling
5. RSS processing for RX packets
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch drops "vmx" prefix from packet abstractions names
to emphasize the fact they are generic and not tied to any
specific network device.
These abstractions will be reused by e1000e emulation implementation
introduced by following patches so their names need generalization.
This patch (except renamed files, adjusted comments and changes in MAINTAINTERS)
was produced by:
git grep -lz 'vmxnet_tx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_tx_pkt/net_tx_pkt/g"
git grep -lz 'vmxnet_rx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_rx_pkt/net_rx_pkt/g"
git grep -lz 'VmxnetTxPkt' | xargs -0 perl -i'' -pE "s/VmxnetTxPkt/NetTxPkt/g"
git grep -lz 'VMXNET_TX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_TX_PKT/NET_TX_PKT/g"
git grep -lz 'VmxnetRxPkt' | xargs -0 perl -i'' -pE "s/VmxnetRxPkt/NetRxPkt/g"
git grep -lz 'VMXNET_RX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_RX_PKT/NET_RX_PKT/g"
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_rx_pkt.c
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_tx_pkt.c
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The last 8 bytes of the receive buffer list page (that has been supplied
by the guest with the H_REGISTER_LOGICAL_LAN call) contain a counter
for frames that have been dropped because there was no suitable receive
buffer available. This patch introduces code to use this field to
provide the information about dropped rx packets to the guest.
There it can be queried with "ethtool -S eth0 | grep rx_no_buffer".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently, the spapr-vlan device is trying to flush the RX queue
after each RX buffer that has been added by the guest via the
H_ADD_LOGICAL_LAN_BUFFER hypercall. In case the receive buffer pool
was empty before, we only pass single packets to the guest this
way. This can cause very bad performance if a sender is trying
to stream fragmented UDP packets to the guest. For example when
using the UDP_STREAM test from netperf with UDP packets that are
much bigger than the MTU size, almost all UDP packets are dropped
in the guest since the chances are quite high that at least one of
the fragments got lost on the way.
When flushing the receive queue, it's much better if we'd have
a bunch of receive buffers available already, so that fragmented
packets can be passed to the guest in one go. To do this, the
spapr_vlan_receive() function should return 0 instead of -1 if there
are no more receive buffers available, so that receive_disabled = 1
gets temporarily set for the receive queue, and we have to delay
the queue flushing at the end of h_add_logical_lan_buffer() a little
bit by using a timer, so that the guest gets a chance to add multiple
RX buffers before we flush the queue again.
This improves the UDP_STREAM test with the spapr-vlan device a lot:
Running
netserver -p 44444 -L <guestip> -f -D -4
in the guest, and
netperf -p 44444 -L <hostip> -H <guestip> -t UDP_STREAM -l 60 -- -m 16384
in the host, I get the following values _without_ this patch:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1738970 0 3798.83
229376 60.00 23 0.05
That "0.05" means that almost all UDP packets got lost/discarded
at the receiving side.
With this patch applied, the value look much better:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1789104 0 3908.35
229376 60.00 22818 49.85
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When receiving packets over MIPSnet network device, it uses
receive buffer of size 1514 bytes. In case the controller
accepts large(MTU) packets, it could lead to memory corruption.
Add check to avoid it.
Reported by: Oleksandr Bazhaniuk <oleksandr.bazhaniuk@intel.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
open_eth_start_xmit has a huge stack usage of 65536 bytes approx.
Moving large arrays to heap to reduce stack usage.
Reduce size of a buffer allocated on stack to 0x600 bytes, which is the
maximal frame length when HUGEN bit is not set in MODER, only allocate
buffer on heap when that is too small. Thus heap is not used in typical
use case.
Signed-off-by: Zhou Jie <zhoujie2011@cn.fujitsu.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Drop local definitions of MII registers and use constants from mii.h for
registers and register bits. No functional changes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reserve this to CPU state serialization.
Luckily, they were only used by sPAPR devices and these are ppc64
only. So there is no change to migration format.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When receiving packets over Stellaris ethernet controller, it
uses receive buffer of size 2048 bytes. In case the controller
accepts large(MTU) packets, it could lead to memory corruption.
Add check to avoid it.
Reported-by: Oleksandr Bazhaniuk <oleksandr.bazhaniuk@intel.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1460095428-22698-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Through CP_TX_OWN and CP_RX_OWN points to the same bit, we'd better use
CP_TX_OWN for tx descriptor handling.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Indicate that autonegotiation is complete in the MII BMSR. This fixes
networking on xtfpga platform in linux v4.5.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This reverts commit 9596ef7c7b.
This workaround in order to fix endless interrupts is no
longer needed because it was superseded by the previous patch
(e1000: Fixing interrupt pace).
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch introduces an upper bound for number of interrupts
per second. Without this bound an interrupt storm can occur as
it has been observed on Windows 10 when disabling the device.
According to the SPEC - Intel PCI/PCI-X Family of Gigabit
Ethernet Controllers Software Developer's Manual, section
13.4.18 - the Ethernet controller guarantees a maximum
observable interrupt rate of 7813 interrupts/sec. If there is
no upper bound this could lead to an interrupt storm by e1000
(when mit_delay < 500) causing interrupts to fire at a very high
pace.
Thus if mit_delay < 500 then the delay should be set to the
minimum delay possible which is 500. This can be calculated
easily as follows:
Interval = 10^9 / (7813 * 256) = 500.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJW9ErPAAoJEL/70l94x66DJfEH/A/QkMpAhrgNdyVsahzsGrzE
wx5gHFIc1nBYxyr62w4apUb5jPB7zaXu0LA7EAWDeAe0pyP8hZzLT9kJyOEDsuJu
zwKN2QeLSNMtPbnbKN0I/YQ2za2xX1V5ruhSeOJoVslUI214hgnAURaGshhQNzuZ
2CluDT9KgL5cQifAnKs5kJrwhIYShYNQB+1eDC/7wk28dd/EH+sPALIoF+rqrSmt
Zu4Mdqd+9Ns+oKOjA6br9ULq/Hzg0aDfY82J+XLVVqfF3PXQe8rTDmuMf/7jTn+M
Un7ZOcei9oZF2/9vfAfKQpDCcgD9HvOUSbgqV/ubmkPPmN/LNJzeKj0fBhrRN+Y=
=K12D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Log filtering from Alex and Peter
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
# gpg: Signature made Thu 24 Mar 2016 20:15:11 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
target-i386: implement PKE for TCG
config.status: Pass extra parameters
char: translate from QIOChannel error to errno
exec: fix error handling in file_ram_alloc
cputlb: modernise the debug support
qemu-log: support simple pid substitution for logs
target-arm: dfilter support for in_asm
qemu-log: dfilter-ise exec, out_asm, op and opt_op
qemu-log: new option -dfilter to limit output
qemu-log: Improve the "exec" TB execution logging
qemu-log: Avoid function call for disabled qemu_log_mask logging
qemu-log: correct help text for -d cpu
tcg: pass down TranslationBlock to tcg_code_gen
util: move declarations out of qemu-common.h
Replaced get_tick_per_sec() by NANOSECONDS_PER_SECOND
hw: explicitly include qemu-common.h and cpu.h
include/crypto: Include qapi-types.h or qemu/bswap.h instead of qemu-common.h
isa: Move DMA_transfer_handler from qemu-common.h to hw/isa/isa.h
Move ParallelIOArg from qemu-common.h to sysemu/char.h
Move QEMU_ALIGN_*() from qemu-common.h to qemu/osdep.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
scripts/clean-includes
RX buffer pools are now enabled by default for new machine types.
For older machine types, they are still disabled to avoid breaking
migration.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
tl;dr:
This patch introduces an alternate way of handling the receive
buffers of the spapr-vlan device, resulting in much better
receive performance for the guest.
Full story:
One of our testers recently discovered that the performance of the
spapr-vlan device is very poor compared to other NICs, and that
a simple "ping -i 0.2 -s 65507 someip" in the guest can result
in more than 50% lost ping packets (especially with older guest
kernels < 3.17).
After doing some analysis, it was clear that there is a problem
with the way we handle the receive buffers in spapr_llan.c: The
ibmveth driver of the guest Linux kernel tries to add a lot of
buffers into several buffer pools (with 512, 2048 and 65536 byte
sizes by default, but it can be changed via the entries in the
/sys/devices/vio/1000/pool* directories of the guest). However,
the spapr-vlan device of QEMU only tries to squeeze all receive
buffer descriptors into one single page which has been supplied
by the guest during the H_REGISTER_LOGICAL_LAN call, without
taking care of different buffer sizes. This has two bad effects:
First, only a very limited number of buffer descriptors is accepted
at all. Second, we also hand 64k buffers to the guest even if
the 2k buffers would fit better - and this results in dropped packets
in the IP layer of the guest since too much skbuf memory is used.
Though it seems at a first glance like PAPR says that we should store
the receive buffer descriptors in the page that is supplied during
the H_REGISTER_LOGICAL_LAN call, chapter 16.4.1.2 in the LoPAPR spec
declares that "the contents of these descriptors are architecturally
opaque, none of these descriptors are manipulated by code above
the architected interfaces". That means we don't have to store
the RX buffer descriptors in this page, but can also manage the
receive buffers at the hypervisor level only. This is now what we
are doing here: Introducing proper RX buffer pools which are also
sorted by size of the buffers, so we can hand out a buffer with
the best fitting size when a packet has been received.
To avoid problems with migration from/to older version of QEMU,
the old behavior is also retained and enabled by default. The new
buffer management has to be enabled via a new "use-rx-buffer-pools"
property.
Now with the new buffer pool management enabled, the problem with
"ping -s 65507" is fixed for me, and the throughput of a simple
test with wget increases from creeping 3MB/s up to 20MB/s!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Refactor the code a little bit by extracting the code that reads
and writes the receive buffer list page into separate functions.
There should be no functional change in this patch, this is just
a preparation for the upcoming extensions that introduce receive
buffer pools.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Manually drop redundant includes that scripts/clean-includes misses,
e.g. because they're hidden in generator programs, or they use the
wrong kind of delimiter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add property to specify rocker world. All ports will be assigned to this
world.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Until now, 0 is returned in this error case. Fix it ro return -ENOMEM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Port to world assignment should be permitted only by qemu user. Driver
should not be able to do it, so forbid that possibility.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. Registers PSTART & PSTOP
define ring buffer size & location. Setting these registers
to invalid values could lead to infinite loop or OOB r/w
access issues. Add check to avoid it.
Reported-by: Yang Hongke <yanghongke@huawei.com>
Tested-by: Yang Hongke <yanghongke@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Since guest_mask_notifier can not be used in vhost-user mode due
to buffering implied by unix control socket, force
use_mask_notifier on virtio devices of vhost-user interfaces, and
send correct callfd to the guest at vhost start.
Using guest_notifier_mask function in vhost-user case may
break interrupt mask paradigm, because mask/unmask is not
really done when returning from guest_notifier_mask call, instead
message is posted in a unix socket, and processed later.
Add an option boolean flag 'use_mask_notifier' to disable the use
of guest_notifier_mask in virtio pci.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cross-endian is now handled by the core virtio-net code.
This patch reverts:
commit 5be7d9f1b1
vhost-net: tell tap backend about the vnet endianness
and
commit cf0a628f6e81bfc9b7a944fa0b80c3594836df56
net: set endianness on all backend devices
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
When running a fully emulated device in cross-endian conditions, including
a virtio 1.0 device offered to a big endian guest, we need to fix the vnet
headers. This is currently handled by the virtio_net_hdr_swap() function
in the core virtio-net code but it should actually be handled by the net
backend.
With this patch, virtio-net now tries to configure the backend to do the
endian fixing when the device starts (i.e. drivers sets the CONFIG_OK bit).
If the backend cannot support the requested endiannes, we have to fallback
onto virtio_net_hdr_swap(): this is recorded in the needs_vnet_hdr_swap flag,
to be used in the TX and RX paths.
Note that we reset the backend to the default behaviour (guest native
endianness) when the device stops (i.e. device status had CONFIG_OK bit and
driver unsets it). This is needed, with the linux tap backend at least,
otherwise the guest may lose network connectivity if rebooted into a
different endianness.
The current vhost-net code also tries to configure net backends. This will
be no more needed and will be reverted in a subsequent patch.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtj8KAAoJECgfDbjSjVRpBIQIAJSB9xwTcBLXwD0+8z5lqjKC
GTtuVbHU0+Y/eO8O3llN5l+SzaRtPHo18Ele20Oz7IQc0ompANY273K6TOlyILwB
rOhrub71uqpOKbGlxXJflroEAXb78xVK02lohSUvOzCDpwV+6CS4ZaSer7yDCYkA
MODZj7rrEuN0RmBWqxbs1R7Mj2CeQJzlgTUNTBGCLEstoZGFOJq8FjVdG5P1q8vI
fnI9mGJ1JsDnmcUZe/bTFfB4VreqeQ7UuGyNAMMGnvIbr0D1a+CoaMdV7/HZ+KyT
5TIs0siVdhZei60A/Cq2OtSVCbj5QdxPBLhZfwJCp6oU4lh2U5tSvva0mh7MwJ0=
=D/cA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc and misc cleanups and fixes, virtio optimizations
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sat 06 Feb 2016 18:44:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (45 commits)
net: set endianness on all backend devices
fix MSI injection on Xen
intel_iommu: large page support
dimm: Correct type of MemoryHotplugState->base
pc: set the OEM fields in the RSDT and the FADT from the SLIC
acpi: add function to extract oem_id and oem_table_id from the user's SLIC
acpi: expose oem_id and oem_table_id in build_rsdt()
acpi: take oem_id in build_header(), optionally
pc: Eliminate PcGuestInfo struct
pc: Move APIC and NUMA data from PcGuestInfo to PCMachineState
pc: Move PcGuestInfo.fw_cfg to PCMachineState
pc: Remove PcGuestInfo.isapc_ram_fw field
pc: Remove RAM size fields from PcGuestInfo
pc: Remove compat fields from PcGuestInfo
acpi: Don't save PcGuestInfo on AcpiBuildState
acpi: Remove guest_info parameters from functions
pc: Simplify xen_load_linux() signature
pc: Simplify pc_memory_init() signature
pc: Eliminate struct PcGuestInfoState
pc: Move PcGuestInfo declaration to top of file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 5be7d9f1b1
vhost-net: tell tap backend about the vnet endianness
makes vhost net to set the endianness of the device, but only for
the first device.
In case of multiqueue, we have multiple devices... This patch sets the
endianness for all the devices of the interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
The return code of virtqueue_pop/vring_pop is unused except to check for
errors or 0. We can thus easily move allocation inside the functions
and just return a pointer to the VirtQueueElement.
The advantage is that we will be able to allocate only the space that
is needed for the actual size of the s/g list instead of the full
VIRTQUEUE_MAX_SIZE items. Currently VirtQueueElement takes about 48K
of memory, and this kind of allocation puts a lot of stress on malloc.
By cutting the size by two or three orders of magnitude, malloc can
use much more efficient algorithms.
The patch is pretty large, but changes to each device are testable
more or less independently. Splitting it would mostly add churn.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The start_xmit() and e1000_receive_iov() functions implement DMA transfers
iterating over a set of descriptors that the guest's e1000 driver
prepares:
- the TDLEN and RDLEN registers store the total size of the descriptor
area,
- while the TDH and RDH registers store the offset (in whole tx / rx
descriptors) into the area where the transfer is supposed to start.
Each time a descriptor is processed, the TDH and RDH register is bumped
(as appropriate for the transfer direction).
QEMU already contains logic to deal with bogus transfers submitted by the
guest:
- Normally, the transmit case wants to increase TDH from its initial value
to TDT. (TDT is allowed to be numerically smaller than the initial TDH
value; wrapping at or above TDLEN bytes to zero is normal.) The failsafe
that QEMU currently has here is a check against reaching the original
TDH value again -- a complete wraparound, which should never happen.
- In the receive case RDH is increased from its initial value until
"total_size" bytes have been received; preferably in a single step, or
in "s->rxbuf_size" byte steps, if the latter is smaller. However, null
RX descriptors are skipped without receiving data, while RDH is
incremented just the same. QEMU tries to prevent an infinite loop
(processing only null RX descriptors) by detecting whether RDH assumes
its original value during the loop. (Again, wrapping from RDLEN to 0 is
normal.)
What both directions miss is that the guest could program TDLEN and RDLEN
so low, and the initial TDH and RDH so high, that these registers will
immediately be truncated to zero, and then never reassume their initial
values in the loop -- a full wraparound will never occur.
The condition that expresses this is:
xdh_start >= s->mac_reg[XDLEN] / sizeof(desc)
i.e., TDH or RDH start out after the last whole rx or tx descriptor that
fits into the TDLEN or RDLEN sized area.
This condition could be checked before we enter the loops, but
pci_dma_read() / pci_dma_write() knows how to fill in buffers safely for
bogus DMA addresses, so we just extend the existing failsafes with the
above condition.
This is CVE-2016-1981.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Prasad Pandit <ppandit@redhat.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-stable@nongnu.org
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1296044
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
gem_transmit copies a packet from guest into an tx_packet[2048]
array on stack, with size limited by descriptor length set by guest. If
guest is malicious and specifies a descriptor length that is too large,
and should packet size exceed array size, this results in a buffer
overflow.
Reported-by: 刘令 <liuling-it@360.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
While receiving packets in 'gem_receive' routine, if Frame Check
Sequence(FCS) is enabled, it copies the packet into a local
buffer without checking its size. Add check to validate packet
length against the buffer size to avoid buffer overflow.
Reported-by: Ling Liu <liuling-it@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-19-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-15-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-14-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
In Xen 4.7 we are refactoring parts libxenctrl into a number of
separate libraries which will provide backward and forward API and ABI
compatiblity.
One such library will be libxengnttab which provides access to grant
tables.
In preparation for this switch the compatibility layer in xen_common.h
(which support building with older versions of Xen) to use what will
be the new library API. This means that the gnttab shim will disappear
for versions of Xen which include libxengnttab.
To simplify things for the <= 4.0.0 support we wrap the int fd in a
malloc(sizeof int) such that the handle is always a pointer. This
leads to less typedef headaches and the need for
XC_HANDLER_INITIAL_VALUE etc for these interfaces.
Note that this patch does not add any support for actually using
libxengnttab, it just adjusts the existing shims.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Replace the uint8 softfloat-specific typedef with uint8_t.
This change was made with
find include hw fpu target-* -name '*.[ch]' | xargs sed -i -e 's/\buint8\b/uint8_t/g'
together with manual removal of the typedef definition and
manual fixing of more erroneous uses found via test compilation.
It turns out that the only code using this type is an accidental
use where uint8_t was intended anyway...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Leon Alrae <leon.alrae@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Message-id: 1452603315-27030-7-git-send-email-peter.maydell@linaro.org
Replace the uint32 softfloat-specific typedef with uint32_t.
This change was made with
find include hw fpu target-* -name '*.[ch]' | xargs sed -i -e 's/\buint32\b/uint32_t/g'
together with manual removal of the typedef definition,
manual undoing of various mis-hits, and another couple of
fixes found via test compilation.
All the uses in hw/ were using the wrong type by mistake.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Leon Alrae <leon.alrae@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Message-id: 1452603315-27030-5-git-send-email-peter.maydell@linaro.org
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <1450370121-5768-5-git-send-email-armbru@redhat.com>
eth.h and slirp.h both define ETH_ALEN and ETH_P_IP
rtl8139.c and eth.h both define ETH_HLEN
Move the related constant (ETH_P_ARP) from slirp.h to eth.h, and
remove the duplicates; make slirp.h include eth.h
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
While processing transmit(tx) descriptors in 'tx_consume' routine
the switch emulator suffers from an off-by-one error, if a
descriptor was to have more than allowed(ROCKER_TX_FRAGS_MAX=16)
fragments. Fix an incorrect bounds check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Following the previous patch which changed vmxnet3 to be a pci express
device, this patch introduces a boolean property 'x-disable-pcie' whose
default is false.
Setting 'x-disable-pcie' to 'on' preserves the old 'pci device' (non
express) behavior. This allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Report the DSN extended PCI capability at 0x100.
DSN value is a transformation of device MAC address, as calculated
by VMware virtual hardware.
DSN is reported only if device is pcie.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Report the 'express endpoint' capability if on a PCIE bus.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Introduce a class type for vmxnet3, and the usual
DEVICE_CLASS/DEVICE_GET_CLASS macros.
No semantic change.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Following the previous patches, where vmxnet3's pci's msi/msix
capability offsets and msix's PBA table offsets have been changed, this
patch introduces a boolean property 'x-old-msi-offsets' to vmxnet3,
whose default is false.
Setting 'x-old-msi-offsets' to 'on' preserves the old offsets behavior,
which allows migration to older versions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Place the PBA table at 0x1000, as placed by VMware virtual hardware.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Place device reported PCI capabilities at the same offsets as placed by
the VMware virtual hardware: MSI at [84], MSI-X at [9c].
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_DEVICE_VERSION is used as return value for accessing
UPT Revision Report and Selection register. So rename it
to VMXNET3_UPT_REVISION.
Signed-off-by: Miao Yan <yanmiaoebest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Return 0 on unknown command, this is what esxi (5.x+) behaves.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_CMD_GET_DEV_EXTRA_INFO should return 0 for emulation
mode
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.x+)
2) modify vmxnet3 Linux driver to read the register:
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DEV_EXTRA_INFO);
ret = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
pr_info("vmxnet3 dev_info: 0x%x\n", ret);
The kernel log will have some like the following message:
[ 7005.111170] vmxnet3 dev_info: 0x0
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_CMD_GET_DID_LO should return PCI ID of the device
and VMXNET3_CMD_GET_DID_HI should return vmxnet3 revision ID.
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.x+)
2) modify vmxnet3 Linux driver to read DID_HI and DID_LO:
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DID_LO);
lo = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DID_HI);
high = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
pr_info("vmxnet3 DID lo: 0x%x, high: 0x%x\n", lo, high);
The kernel log will have something like the following message:
[ 7005.111170] vmxnet3 DID lo: 0x7b0, high: 0x1
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When reading device status, 0 means device is successfully
activated and 1 means error.
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.5+)
2) modify vmxnet3 Linux driver to give it an invalid
address to 'adapter->shared_pa' which is the
shared memory for guest/host communication
This will trigger device activation failure and kernel
log will have the following message:
[ 7138.403256] vmxnet3 0000:03:00.0 eth1: Failed to activate dev: error 1
So return 1 on device activation failure instead of -1;
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Vmxnet3 device emulator does not check if the device is active
before activating it, also it did not free the transmit & receive
buffers while deactivating the device, thus resulting in memory
leakage on the host. This patch fixes both these issues to avoid
host memory leakage.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Macro VMW_SHPRN(...) is already defined vmxnet3_debug.h,
so remove the duplication
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Vmxnet3 uses the following debug macro style:
#ifdef SOME_DEBUG
# define debug(...) do{ printf(...); } while (0)
# else
# define debug(...) do{ } while (0)
#endif
If SOME_DEBUG is undefined, then format string inside the
debug macro will never be checked by compiler. Code is
likely to break in the future when SOME_DEBUG is enabled
because of lack of testing. This patch changes this
to the following:
#define debug(...) \
do { if (SOME_DEBUG_ENABLED) printf(...); } while (0)
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use %zu specifier for size_t in printf, otherwise build would fail
on platforms where size_t is not unsigned long
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Macro MAC_FMT and MAC_ARG are not defined, but used in vmxnet3_net_init().
This will cause build error when debug level is raised in
vmxnet3_debug.h (enable all VMXNET3_DEBUG_xxx).
Use VMXNET_MF and VXMNET_MA instead.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJWZZJPAAoJEO8Ells5jWIRmp0H/26aFXVEgZykkUVNbqq05r7w
AI7podQlFOAESJHqZtR8FMaH8TAZ5GhphP4pn0PsWp54VjwcYZbdoME+dhZ4Elyc
WDanRHIweLv/zVg6+M8oHhw5GMaxtFLoLWrf0oanbUW9IZZmmM3COz/Y31hSVrR2
EzEJi1VZZhpMj3ibeOJns4MrugYrne8MtOdvusE/Uw2rJBTiStnWw1eTk8RmkNcg
5un1mQZxFU2AcNzmWdmWJmjY0rCnR3HhtTdZOwjM6uZGIJ9hbsItGzqiGadBfozI
fUtIa2HZahioe0VIzoB0snXnAuhV1jA0Uy18i04dPvgQOmiVSRjQNE2/lwQflyE=
=Pad3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 07 Dec 2015 14:06:07 GMT using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
lan9118: log and ignore access to invalid registers, rather than aborting
lan9118: fix emulation of MAC address loaded bit in E2P_CMD register
vmxnet3: silence warning
pcnet: fix rx buffer overflow(CVE-2015-7512)
net: pcnet: add check to validate receive data size(CVE-2015-7504)
e1000: fix hang of win2k12 shutdown with flood ping
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this change, access to invalid/unimplemented device registers are
logged as a "guest error" rather than aborting qemu with
hw_error. This enables drivers for similar devices (e.g. SMSC 9221),
by simply ignoring the unimplemented writes. It's also closer to what
real hardware does.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
There appears to have been a longstanding typo in the implementation
of the "MAC address loaded" bit in the E2P_CMD (EEPROM command)
register. The code was using 0x10, but the controller spec says it
should be bit 8 (0x100).
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
vmxnet3 always produces a warning under qtest.
This is not a user error, don't warn.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Backends could provide a packet whose length is greater than buffer
size. Check for this and truncate the packet to avoid rx buffer
overflow in this case.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In loopback mode, pcnet_receive routine appends CRC code to the
receive buffer. If the data size given is same as the buffer size,
the appended CRC code overwrites 4 bytes after s->buffer. Added a
check to avoid that.
Reported by: Qinghao Tang <luodalongde@gmail.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000 driver in Win2k12 is really well rotten. It 100% hangs on shutdown
of UP VM under flood ping. The guest checks card state and reinjects
itself interrupt in a loop. This is fatal for UP machine.
There is no good way to fix this misbehavior but to kludge it. The
emulation has interrupt throttling register aka ITR which limits
interrupt rate and allows the guest to proceed this phase.
There is no problem with this kludge for Linux guests - it adjust the
value of it itself.
On the other hand according to the initial research in
commit e9845f0985
Author: Vincenzo Maffione <v.maffione@gmail.com>
Date: Fri Aug 2 18:30:52 2013 +0200
e1000: add interrupt mitigation support
...
Interrupt mitigation boosts performance when the guest suffers from
an high interrupt rate (i.e. receiving short UDP packets at high packet
rate). For some numerical results see the following link
http://info.iet.unipi.it/~luigi/papers/20130520-rizzo-vm.pdf
this should also boost performance a bit.
See https://bugzilla.redhat.com/show_bug.cgi?id=874406 for additional
details.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vincenzo Maffione <v.maffione@gmail.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
http://lists.nongnu.org/archive/html/qemu-devel/2015-11/msg04592.html
shows an example how an endless loop in function action_command can
be achieved.
During my code review, I noticed a 2nd case which can result in an
endless loop.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Some features (such as ctrl vq) are supported
by qemu without need to communicate with the
backend.
Drop them from the feature mask so we set them
unconditionally.
Reported-by: Victor Kaplansky <vkaplans@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
First of all, RESET_OWNER message is sent incorrectly, as it's sent
before GET_VRING_BASE. And the reset message would let the later call
get nothing correct.
And, sending SET_VRING_ENABLE at stop, which has already been done,
makes more sense than RESET_OWNER.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJWREdzAAoJEO8Ells5jWIRI18H/0CEDVwj7AJHLEpAv07hX2iS
jfq6Osgj5hDChv43+66Clz3owog3m9NfPKWxBMvIw5c/Q1mFvNuxZcUaVOzX2dT4
E+IwIsZxXOANIGPYtCxOhARz1zNSDxJxgYPMVuIDZ+uZVJqYeCjdduMGzgy8wt8H
qiquUCI2sktg97AntZqzp8iWfZZIN5w6uNbf3FvgwIffWDxGRPt8wY6dlwgIpsx2
uFd9PMwtj7lJyV9guy36FdrS7MhVTCF5/5GIerPj2nN1ByJp9vu5InzPAlmZNRSZ
KxKcBnmkLsnT3nDN86ZS6ajDyjeEgWSVdrQS9MHDURfinADuuqjbJkhME/UhG+g=
=vRNP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 12 Nov 2015 08:01:55 GMT using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: netmap: use error_setg() helpers in place of error_report()
net: netmap: Fix compilation issue
e1000: Introducing backward compatibility command line parameter
e1000: Implementing various counters
e1000: Fixing the packet address filtering procedure
e1000: Fixing the received/transmitted octets' counters
e1000: Fixing the received/transmitted packets' counters
e1000: Trivial implementation of various MAC registers
e1000: Introduced an array to control the access to the MAC registers
e1000: Add support for migrating the entire MAC registers' array
e1000: Cosmetic and alignment fixes
slirp: Fix type casts and format strings in debug code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This follows the previous patches, where support for migrating the
entire MAC registers' array, and some new MAC registers were introduced.
This patch introduces the e1000-specific boolean parameter
"extra_mac_registers", which is on by default. Setting it to off will
enable migration to older versions of QEMU, but will disable the read
and write access to the new registers, that were introduced since adding
the ability to migrate the entire MAC array.
Example for usage to enable backward compatibility and to disable the
new MAC registers:
qemu-system-x86_64 -device e1000,extra_mac_registers=off,... ...
As mentioned above, the default value is "on".
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This implements the following Statistic registers (various counters)
according to Intel's specs:
TSCTC GOTCL GOTCH GORCL GORCH MPRC BPRC RUC ROC
BPTC MPTC PTC... PRC...
PLEASE NOTE: these registers will not be active, nor will migrate, until
a compatibility flag will be set (in the next patch in this series).
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Previously, if promiscuous unicast was enabled, a packet was received
straight away, even if it was a multicast or a broadcast packet. This
patch fixes that behavior, while making the filtering procedure a bit
more human-readable.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Previously, these 64-bit registers did not stick at their maximal
values when (and if) they reached them, as they should do, according to
the specs.
This patch introduces a function that takes care of such registers,
avoiding code duplication, making the relevant parts more compatible
with the QEMU coding style, while ensuring that in the unlikely case
of reaching the maximal value, the counter will stick there, as it
supposed to.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to Intel's specs, these counters (as the other Statistic
registers) stick at 0xffffffff when this maximal value is reached.
Previously, they would reset after the max. value.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
These registers appear in Intel's specs, but were not implemented.
These registers are now implemented trivially, i.e. they are initiated
with zero values, and if they are RW, they can be written or read by the
driver, or read only if they are R (essentially retaining their zero
values). For these registers no other procedures are performed.
For the trivially implemented Diagnostic registers, a debug warning is
produced on read/write attempts.
PLEASE NOTE: these registers will not be active, nor will migrate, until
a compatibility flag will be set (in a later patch in this series).
The registers implemented here are:
Transmit:
RW: AIT
Management:
RW: WUC WUS IPAV IP6AT* IP4AT* FFLT* WUPM* FFMT* FFVT*
Diagnostic:
RW: RDFH RDFT RDFHS RDFTS RDFPC PBM* TDFH TDFT TDFHS
TDFTS TDFPC
Statistic:
RW: FCRUC
R: RNBC TSCTFC MGTPRC MGTPDC MGTPTC RFC RJC SCC ECOL
LATECOL MCC COLC DC TNCRS SEC CEXTERR RLEC XONRXC
XONTXC XOFFRXC XOFFTXC
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The array of uint8_t's which is introduced here, contains access metadata
about the MAC registers: if a register is accessible, but partly implemented,
or if a register requires a certain compatibility flag in order to be
accessed. Currently, 6 hypothetical flags are supported (3 exist for e1000
so far) but in the future, if more than 6 flags will be needed, the datatype
of this array can simply be swapped for a larger one.
This patch is intended to solve the following current problems:
1) In a scenario of migration between different versions of QEMU, which
differ by the MAC registers implemented in them, some registers need not to
be active if a compatibility flag is set, in order to preserve the machine's
state perfectly for the older version. Checking this for each register
individually, would create a lot of clutter in the code.
2) Some registers are (or may be) only partly implemented (e.g.
placeholders that allow reading and writing, but lack other functions).
In such cases it is better to print a debug warning on read/write attempts.
As above, dealing with this functionality on a per-register level, would
require longer and more messy code.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch makes the migration of the entire array of MAC registers
possible during live migration. The entire array is just 128 KB long, so
practically no penalty should be felt when transmitting it, additionally
to the previously transmitted individual registers. The advantage here is
eliminating the need to introduce new vmstate subsections in the future,
when additional MAC registers will be implemented.
Backward compatibility is preserved by introducing a e1000-specific
boolean parameter (in a later patch), which will be on by default.
Setting it to off would enable migration to older versions of QEMU.
Additionally, this parameter will be used to control the access to the
extra MAC registers in the future.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This fixes some alignment and cosmetic issues. The changes are made
in order that the following patches in this series will look like
integral parts of the code surrounding them, while conforming to the
coding style. Although some changes in unrelated areas are also made.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A few uses of error_set(ERROR_CLASS_GENERIC_ERROR) were missed in
c6bd8c706, or have snuck in since. Nuke them.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1447224690-9743-19-git-send-email-eblake@redhat.com>
Acked-by: Andreas Färber <afaerber@suse.de>
[Indentation tidied up, commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() output is following the same format as the
above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 57e565982db94fb433c32dfa17608888464d21de.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Guest OS may issue VMXNET3_CMD_GET_STATS even before device was
activated (for example in linux, after insmod but prior net-dev open).
Accessing shared descriptors prior device activation is illegal as the
VMXNET3State structures have not been fully initialized.
As a result, guest memory gets corrupted and may lead to guest OS
crashes.
Fix, by not filling the stats descriptors if device is inactive.
Reported-by: Leonid Shatz <leonid.shatz@ravellosystems.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Set initial MAC address to the one specified by the command line.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A new vhost user message is added to allow QEMU to ask to vhost user backend to
broadcast a fake RARP after live migration for guest without GUEST_ANNOUNCE
capability.
This new message is sent only if the backend supports the new
VHOST_USER_PROTOCOL_F_RARP protocol feature.
The payload of this new message is the MAC address of the guest (not known by
the backend). The MAC address is copied in the first 6 bytes of a u64 to avoid
to create a new payload message type.
This new message has no equivalent ioctl so a new callback is added in the
userOps structure to send the request.
Upon reception of this new message the vhost user backend must generate and
broadcast a fake RARP request to notify the migration is terminated.
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
[Rebased and fixed checkpatch errors - Marc-André]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Some vhost user backends are able to support live migration.
To provide this service the following features must be added:
1. Add the VIRTIO_NET_F_GUEST_ANNOUNCE capability to vhost-net when netdev
backend is vhost-user.
2. Provide a nop receive callback to vhost-user.
This callback is called by:
* qemu_announce_self after a migration to send fake RARP to avoid network
outage for peers talking to the migrated guest.
- For guest with GUEST_ANNOUNCE capabilities, guest already sends GARP
when the bit VIRTIO_NET_S_ANNOUNCE is set.
=> These packets must be discarded.
- For guest without GUEST_ANNOUNCE capabilities, migration termination
is notified when the guest sends packets.
=> These packets can be discarded.
* virtio_net_tx_bh with a dummy boot to send fake bootp/dhcp request.
BIOS guest manages virtio driver to send 4 bootp/dhcp request in case of
dummy boot.
=> These packets must be discarded.
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Replace the generic vhost_call() by specific functions for each
function call to help with type safety and changing arguments.
While doing this, I found that "unsigned long long" and "uint64_t" were
used interchangeably and causing compilation warnings, using uint64_t
instead, as the vhost & protocol specifies.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[Fix enum usage and MQ - Thibaut Collet]
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Version: GnuPG v1
iQEcBAABAgAGBQJWG2e/AAoJEO8Ells5jWIRcYcH/2D11W8cToCBjGDuw/u9K1ht
S3oGyFasOEq3lm3+a3zQE+vDw0RDkjLEMhcTVwNskJQl6k6Ts5JleTZ6wffvUKPM
UCozgPOCt1ZAdGskwdbByc+NhaVBHIiEsmlbDKqP22CENdDx6GWjcFW4brA4tQJQ
AW36EH77j/M+7/KiSukcUfIexILUZJRfN+ICJVyNTpGsqUNJtFqiVPBMPyJhKCEq
3pr3yJ2lf78SAEF5kBeBc9r/PDWUhtqExBsrK0L8Ey1FdrCy8ldqDPGecT4TsxNv
W/KX5AqhKSsMI8DQKdbv/IKaUdjYWNjTRQ2Qjm8Vt0hcW0PhxR0NYi6bV4yjDNM=
=f26Q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 12 Oct 2015 08:56:47 BST using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tests: add test cases for netfilter object
netfilter: add a netbuffer filter
net/queue: export qemu_net_queue_append_iov
netfilter: print filter info associate with the netdev
netfilter: add an API to pass the packet to next filter
net/queue: introduce NetQueueDeliverFunc
net: merge qemu_deliver_packet and qemu_deliver_packet_iov
netfilter: hook packets before net queue send
init/cleanup of netfilter object
vl.c: init delayed object after net_init_clients
vmxnet3: Add support for VMXNET3_CMD_GET_ADAPTIVE_RING_INFO command
e1000: use alias for default model
vmxnet3: Support reading IMR registers on bar0
net/vmxnet3: Refine l2 header validation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some drivers (e.g. vmware-tools) issue the VMXNET3_CMD_GET_ADAPTIVE_RING_INFO
command.
Currently, due to lack of support, a bogus value (-1) is returned.
Support this command, returning the "adaptive-ring disabled" flag.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Instead of duplicating the "e1000-82540em" device model as "e1000",
make the latter an alias for the former.
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Instead of asserting, return the actual IMR register value.
This is aligned with what's returned on ESXi.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Tested-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Validation of l2 header length assumed minimal packet size as
eth_header + 2 * vlan_header regardless of the actual protocol.
This caused crash for valid non-IP packets shorter than 22 bytes, as
'tx_pkt->packet_type' hasn't been assigned for such packets, and
'vmxnet3_on_tx_done_update_stats()' expects it to be properly set.
Refine header length validation in 'vmxnet_tx_pkt_parse_headers'.
Check its return value during packet processing flow.
As a side effect, in case IPv4 and IPv6 header validation failure,
corrupt packets will be dropped.
Signed-off-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T). Same Coccinelle semantic patchas in commit b45c03f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When packet is truncated during receiving, we drop the packets but
neither discard the descriptor nor add and signal used
descriptor. This will lead several issues:
- sg mappings are leaked
- rx will be stalled if a lots of packets were truncated
In order to be consistent with vhost, fix by discarding the descriptor
in this case.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Originally, timers were ticks based, and it made sense to
add ticks to current time to know when to trigger an alarm.
But since commit:
7447545 change all other clock references to use nanosecond resolution accessors
All timers use nanoseconds and we need to convert ticks to nanoseconds, by
doing something like:
y = muldiv64(x, get_ticks_per_sec(), PCI_FREQUENCY)
where x is the number of device ticks and y the number of system ticks.
y is used as nanoseconds in timer functions,
it works because 1 tick is 1 nanosecond.
(get_ticks_per_sec() is 10^9)
But as PCI frequency is 33 MHz, we can also do:
y = x * 30; /* 33 MHz PCI period is 30 ns */
Which is much more simple.
This implies a 33.333333 MHz PCI frequency,
but this is correct.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Originally, timers were ticks based, and it made sense to
add ticks to current time to know when to trigger an alarm.
But since commit:
7447545 change all other clock references to use nanosecond resolution accessors
All timers use nanoseconds and we need to convert ticks to nanoseconds, by
doing something like:
y = muldiv64(x, get_ticks_per_sec(), PCI_FREQUENCY)
where x is the number of device ticks and y the number of system ticks.
y is used as nanoseconds in timer functions,
it works because 1 tick is 1 nanosecond.
(get_ticks_per_sec() is 10^9)
But as PCI frequency is 33 MHz, we can also do:
y = x * 30; /* 33 MHz PCI period is 30 ns */
Which is much more simple.
This implies a 33.333333 MHz PCI frequency,
but this is correct.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a new message, VHOST_USER_SET_VRING_ENABLE, to enable or disable
a specific virt queue, which is similar to attach/detach queue for
tap device.
virtio driver on guest doesn't have to use max virt queue pair, it
could enable any number of virt queue ranging from 1 to max virt
queue pair.
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
This patch is initially based a patch from Nikolay Nikolaev.
This patch adds vhost-user multiple queue support, by creating a nc
and vhost_net pair for each queue.
Qemu exits if find that the backend can't support the number of requested
queues (by providing queues=# option). The max number is queried by a
new message, VHOST_USER_GET_QUEUE_NUM, and is sent only when protocol
feature VHOST_USER_PROTOCOL_F_MQ is present first.
The max queue check is done at vhost-user initiation stage. We initiate
one queue first, which, in the meantime, also gets the max_queues the
backend supports.
In older version, it was reported that some messages are sent more times
than necessary. Here we came an agreement with Michael that we could
categorize vhost user messages to 2 types: non-vring specific messages,
which should be sent only once, and vring specific messages, which should
be sent per queue.
Here I introduced a helper function vhost_user_one_time_request(), which
lists following messages as non-vring specific messages:
VHOST_USER_SET_OWNER
VHOST_USER_RESET_DEVICE
VHOST_USER_SET_MEM_TABLE
VHOST_USER_GET_QUEUE_NUM
For above messages, we simply ignore them when they are not sent the first
time.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
This is for querying how many queues the backend supports if it has mq
support(when VHOST_USER_PROTOCOL_F_MQ flag is set from the quried
protocol features).
vhost_net_get_max_queues() is the interface to export that value, and
to tell if the backend supports # of queues user requested, which is
done in the following patch.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
Quote from Michael:
We really should rename VHOST_RESET_OWNER to VHOST_RESET_DEVICE.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
Support a separate bitmask for vhost-user protocol features,
and messages to get/set protocol features.
Invoke them at init.
No features are defined yet.
[ leverage vhost_user_call for request handling -- Yuanhan Liu ]
Signed-off-by: Michael S. Tsirkin <address@hidden>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
After commit 019a3edbb2 ("virtio: make
features 64bit wide"). Device's guest_features was actually set after
vdc->load(). This breaks the assumption that device specific load()
function can check guest_features. For virtio-net, self announcement
and guest offloads won't work after migration.
Fixing this by defer them to virtio_net_load() where guest_features
were guaranteed to be set. Other virtio devices looks fine.
Fixes: 019a3edbb2
("virtio: make features 64bit wide")
Cc: qemu-stable@nongnu.org
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Symptom:
$ qemu-system-x86_64 -m 10000000
Unexpected error in ram_block_add() at /work/armbru/qemu/exec.c:1456:
upstream-qemu: cannot set up guest memory 'pc.ram': Cannot allocate memory
Aborted (core dumped)
Root cause: commit ef701d7 screwed up handling of out-of-memory
conditions. Before the commit, we report the error and exit(1), in
one place, ram_block_add(). The commit lifts the error handling up
the call chain some, to three places. Fine. Except it uses
&error_abort in these places, changing the behavior from exit(1) to
abort(), and thus undoing the work of commit 3922825 "exec: Don't
abort when we can't allocate guest memory".
The three places are:
* memory_region_init_ram()
Commit 4994653 (right after commit ef701d7) lifted the error
handling further, through memory_region_init_ram(), multiplying the
incorrect use of &error_abort. Later on, imitation of existing
(bad) code may have created more.
* memory_region_init_ram_ptr()
The &error_abort is still there.
* memory_region_init_rom_device()
Doesn't need fixing, because commit 33e0eb5 (soon after commit
ef701d7) lifted the error handling further, and in the process
changed it from &error_abort to passing it up the call chain.
Correct, because the callers are realize() methods.
Fix the error handling after memory_region_init_ram() with a
Coccinelle semantic patch:
@r@
expression mr, owner, name, size, err;
position p;
@@
memory_region_init_ram(mr, owner, name, size,
(
- &error_abort
+ &error_fatal
|
err@p
)
);
@script:python@
p << r.p;
@@
print "%s:%s:%s" % (p[0].file, p[0].line, p[0].column)
When the last argument is &error_abort, it gets replaced by
&error_fatal. This is the fix.
If the last argument is anything else, its position is reported. This
lets us check the fix is complete. Four positions get reported:
* ram_backend_memory_alloc()
Error is passed up the call chain, ultimately through
user_creatable_complete(). As far as I can tell, it's callers all
handle the error sanely.
* fsl_imx25_realize(), fsl_imx31_realize(), dp8393x_realize()
DeviceClass.realize() methods, errors handled sanely further up the
call chain.
We're good. Test case again behaves:
$ qemu-system-x86_64 -m 10000000
qemu-system-x86_64: cannot set up guest memory 'pc.ram': Cannot allocate memory
[Exit 1 ]
The next commits will repair the rest of commit ef701d7's damage.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-3-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
The SOFT_RST or RXEN in the control register can be used as a condition
to unblock the net layer via can_receive(). So check for possible
flushes on RCR changes. This will drop all pending packets on soft
reset or disable which is the functional intent of the can_receive()
logic.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Message-id: b114d4c96f4afbdaa15f1361d9c07e3021755915.1441873621.git.crosthwaite.peter@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Return false from can_receive() when the FIFO doesn't have a free RX
slot. This fixes a bug in the current code where the allocated buffer
is freed before the fifo pop, triggering a premature flush of queued RX
packets. It also will handle a corner case, where the guest manually
frees the allocated buffer before popping the rx FIFO (hence it is not
enough to just delay the flush_queued_packets()).
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Message-id: 97bfdfc5cbce0bd5e0cbbbff35ce7a1bf6f8603d.1441873621.git.crosthwaite.peter@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Check that the core can once again receive packets before asking the
net layer to do a flush. This will make it more convenient to flush
packets when adding new conditions to can_receive.
Add missing if braces while moving the can_receive() core code.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Message-id: 92e15e12a6964274f4bc0eb71b61a7d94326f6c6.1441873621.git.crosthwaite.peter@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. While receiving packets
via ne2000_receive() routine, a local 'index' variable
could exceed the ring buffer size, leading to an infinite
loop situation.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: P J P <pjp@fedoraproject.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. While receiving packets
via ne2000_receive() routine, a local 'index' variable
could exceed the ring buffer size, which could lead to a
memory buffer overflow. Added other checks at initialisation.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: P J P <pjp@fedoraproject.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While processing transmit descriptors, it could lead to an infinite
loop if 'bytes' was to become zero; Add a check to avoid it.
[The guest can force 'bytes' to 0 by setting the hdr_len and mss
descriptor fields to 0.
--Stefan]
Signed-off-by: P J P <pjp@fedoraproject.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1441383666-6590-1-git-send-email-stefanha@redhat.com
My Coccinelle semantic patch finds a few more, because it also fixes up
the equally pointless conditional
if (foo) {
free(foo);
foo = NULL;
}
Result (feel free to squash it into your patch):
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The free() and g_free() functions both happily accept
NULL on any platform QEMU builds on. As such putting a
conditional 'if (foo)' check before calls to 'free(foo)'
merely serves to bloat the lines of code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A number of files were including signal.h but not using any
of the functions it provides
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Many source files have doubled words (eg "the the", "to to",
and so on). Most of these can simply be removed, but a couple
were actual mis-spellings (eg "to to" instead of "to do").
There was even one triple word score "to to to" :-)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit ef546f1275 ("virtio: add
feature checking helpers") introduced a helper __virtio_has_feature.
We don't want to use reserved identifiers, though, so let's
rename __virtio_has_feature to virtio_has_feature and virtio_has_feature
to virtio_vdev_has_feature.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Bit 15 of the PHY Specific Status Register is reserved and
should remain 0. Fix the reset value to ensure that the 15th
bit is not set.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: c795069e49040ff770fe2ece19dfe1791b729e22.1441316450.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is based on mcf_fec.c FEC implementation for Coldfire
* A generic PHY was added (borrowwed from LAN9118)
* The buffer management is also modified as buffers are
slightly different between Coldfire and i.MX
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: fb314f8a120aa49f8f6ad886f312c649b484fb5a.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ne2000_receive already checks the same conditions and drops the packet
if it's not ready, removing the .can_receive callback avoids the
necessity to add explicit flushes when the conditions turn true (which
is required by the new semantics of .can_receive since 6e99c63
"net/socket: Drop net_socket_can_send").
Plus the "return 1" if E8390_STOP is also suspicious.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 6e99c63 ("net/socket: Drop net_socket_can_send") changed the
semantics around .can_receive for sockets to now require the device to
flush queued pkts when transitioning to a .can_receive=true state. But
it's OK to drop incoming packets when the link is not active.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When operation in standard mode, we currently return the size
of packet during buffer overflow. This consumes the overflow
packet. Return 0 instead so we can re-process the overflow packet
when we have room.
This fixes issues with lost/dropped fragments of large messages.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1441121206-6997-3-git-send-email-vyasevic@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
rtl8139_do_receive() tries to check for the overflow condition
by making sure that packet_size + 8 does not exceed the
available buffer space. The issue here is that RxBuffAddr,
used to calculate available buffer space, is aligned to a
a 4 byte boundry after every update. So it is possible that
every packet ends up being slightly padded when written
to the receive buffer. This padding is not taken into
account when checking for overflow and we may end up missing
the overflow condition can causing buffer overwrite.
This patch takes alignment into consideration when
checking for overflow condition.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1441121206-6997-2-git-send-email-vyasevic@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The tx offload feature accesses a 16-bit aligned TCP header struct. The
32-bit fields must be accessed using ldl/stl wrappers since some host
architectures fault on unaligned access.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1438604157-29664-4-git-send-email-stefanha@redhat.com
Eliminate the following "custom" macros since they are just duplicates
of net/eth.h macros under a different name:
ETHER_ADDR_LEN -> ETH_ALEN
ETH_P_8021Q -> ETH_P_VLAN
IP_HEADER_LENGTH -> IP_HDR_GET_LEN
TCP_FLAG_FIN -> TH_FIN
TCP_FLAG_PUSH -> TH_PUSH
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1438604157-29664-3-git-send-email-stefanha@redhat.com
The transmit offload features inspect Ethernet, IP, TCP, and UDP
headers. Avoid redefining these net/eth.h structs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1438604157-29664-2-git-send-email-stefanha@redhat.com
After commit 40bad8f3deba15e2074ff34cfe923c12916b1cc5("virtio-net: fix
used len for tx"), async_tx.len was no longer used afterwards. So
remove useless codes with it.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
From: Dana Rubin <dana.rubin@ravellosystems.com>
In commit 80da311d81,
"net/vmxnet3: Fix RX TCP/UDP checksum on partially summed packets"
a debug message was introduced in vmxnet3_rx_need_csum_calculate() for
an unlikely input condition.
The message accidentally printed 'len' variable instead of 'pkt_len'.
Fix, providing the correct argument.
Signed-off-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-id: 1438109090-18957-1-git-send-email-shmulik.ladkani@ravellosystems.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The TCP Data Offset field contains the length of the header. Make sure
it is valid and does not exceed the IP data length.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
TCP Large Segment Offload accesses the TCP header in the packet. If the
packet is too short we must not attempt to access header fields:
tcp_header *p_tcp_hdr = (tcp_header*)(eth_payload_data + hlen);
int tcp_hlen = TCP_HEADER_DATA_OFFSET(p_tcp_hdr);
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IP Total Length field includes the IP header and data. Make sure it
is valid and does not exceed the Ethernet payload size.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IP Header Length field was only checked in the IP checksum case, but
is used in other cases too.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Transmit offload features access Ethernet and IP headers the packet. If
the packet is too short we must not attempt to access header fields:
int proto = be16_to_cpu(*(uint16_t *)(saved_buffer + 12));
...
eth_payload_data = saved_buffer + ETH_HLEN;
...
ip = (ip_header*)eth_payload_data;
if (IP_HEADER_VERSION(ip) != IP_HEADER_VERSION_4) {
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The previous patch stopped using the ip pointer as an indicator that the
IP header is present. When we reach the if (ip) {...} statement we know
ip is always non-NULL.
Remove the if statement to reduce nesting.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Transmit offload needs to parse packet headers. If header fields have
unexpected values the offload processing is skipped.
The code currently uses nested ifs because there is relatively little
input validation. The next patches will add missing input validation
and a goto label is more appropriate to avoid deep if statement nesting.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
These two .can_receive() are now reviewed. The net subsystem queue for 2.4 is now empty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVt3TbAAoJEJykq7OBq3PIxcQH/2LEY8q3zetJdNe9Zu1bQMhQ
J/Ah+szCNCCHOpNfQEBI6zRT4wUMZZTlIUM1el2ykYnYqRYd585GK/+RZ0/yWQUG
yYNWAFfj/b586+aazk2+BnosSywVjCZ1f32OtaAsh14c+3aoXkQyahljA4onIuVp
kLi1psmnBZgRf6AeICnuUTTOYq8BBX6CTg0sxPpIbZe57epwGkK+6gtZV6aSW/Ra
lbkhXNrmyyvycGuOLDpyjE3yUvHuwn+H+JFeRklTEA2pKyMg1AYVMrIKvBeQej8u
g4+sYYME0rMuFL9iISwVYnkTBjYZnE8+6on2ELkElGvWf28kqb1rYWYciyRhf1Y=
=K3Fg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/net-pull-request' into staging
Pull request
These two .can_receive() are now reviewed. The net subsystem queue for 2.4 is now empty.
# gpg: Signature made Tue Jul 28 13:26:03 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/net-pull-request:
xen: Drop net_rx_ok
hw/net: handle flow control in mcf_fec driver receiver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mostly virtio 1 spec compliance fixes.
We are unlikely to make it perfectly compliant in
the first release, but it seems worth it to try.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVtprUAAoJECgfDbjSjVRpgu4H/AljqEXBYIS/+7aZBGO4UnK/
LSyxiOfw/sQPwYr8xqhYtoITVPQqkBnCajBFuDw3IaGrTDQ1pHfG8z5qt3Fri+yC
RtiqiFg1LVR/AI8W/dUDuLAf8xq1GukZr1o59mi3hAA0pcPxUtVjPkZcaq63d0P+
uzCgRw0qlg8nbT7SN2O9HZz7AT2emaUkaJBF2eRBb7r1kg3ZzM0FOtmCWaRhtS5s
8AuHS+038BWA0J/S7yd5YooQh7NfvmWFpRNukMttJrtOmi7f5LCJJF9rxcXAnzOn
Soc0afauCtUTfxJ4gkLqxQ586eKpREQ+7lzkJDQ62g1oD/+VatOMcbu3jdnJEtQ=
=AoJS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio fixes for 2.4
Mostly virtio 1 spec compliance fixes.
We are unlikely to make it perfectly compliant in
the first release, but it seems worth it to try.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jul 27 21:55:48 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
virtio: minor cleanup
acpi: fix pvpanic device is not shown in ui
virtio-blk: only clear VIRTIO_F_ANY_LAYOUT for legacy device
virtio-blk: fail get_features when both scsi and 1.0 were set
virtio: get_features() can fail
virtio-pci: fix memory MR cleanup for modern
virtio: set any_layout in virtio core
virtio-9p: fix any_layout
virtio-serial: fix ANY_LAYOUT
virtio: hide legacy features from modern guests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let net_rx_packet() (which checks the same conditions) drops the packet
if the device is not ready. Drop net_xen_info.can_receive and update the
return value for the buffer full case.
We rely on the qemu_flush_queued_packets() in net_event() to wake up
the peer when the buffer becomes available again.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1438077176-378-1-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The network mcf_fec driver emulated receive side method is not dealing
with network queue flow control properly.
Modify the receive side to check if we have enough space in the
descriptors to store the current packet. If not we process none of it
and return 0. When the guest frees up some buffers through its descriptors
we signal the qemu net layer to send more packets.
[Fixed coding style: 4-space indent and curly braces on if statement.
--Stefan]
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Message-id: 1438045374-10358-1-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Replace memory_region_init_rom_device() with memory_region_init_ram() and
memory_region_set_readonly().
This fixes a guest-triggerable QEMU crash when guest tries to write to PROM.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[leon.alrae@imgtec.com: shorten subject length]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Ethernet requires that messages are at least 64 bytes on the wire. This
limitation does not exist on emulation (no wire message), so remove the
check. Netcard is now able to receive small network packets.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Netcard needs an address space to write data to, which can't be specified
on command line.
This fixes a crash when user starts QEMU with "-device dp8393x"
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
eth_can_rx checks s->rxsize and returns false if it is non-zero. Because
of the .can_receive semantics change, this will make the incoming queue
disabled by peer, until it is explicitly flushed. So we should flush it
when s->rxsize is becoming zero.
Squash eth_can_rx semantics into etx_rx and drop .can_receive()
callback, also add flush when rx buffer becomes available again after a
packet gets queued.
The other conditions, "!axienet_rx_resetting(s) &&
axienet_rx_enabled(s)" are OK because enet_write already calls
qemu_flush_queued_packets when the register bits are changed.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-13-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.can_receive callback changes semantics that once return 0, backend will
try sending again until explicitly flushed, change the device to meet
that.
dp8393x_can_receive checks SONIC_CR_RXEN bit in SONIC_CR register and
SONIC_ISR_RBE bit in SONIC_ISR register, try flushing the queue when
either bit is being updated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-12-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If s->np reaches 31, the queue will be disabled by peer when it sees
stellaris_enet_can_receive() returns false, until we explicitly flushes
it which notifies the peer. Do this when guest is done reading all
existing data.
Move the semantics to stellaris_enet_receive, by returning 0 when the
buffer is full, so that new packets will be queued. In
stellaris_enet_read, flush and restart the queue when guest has done
reading.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-11-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop .can_receive and move the semantics to mipsnet_receive, by
returning 0.
After 0 is returned, we must flush the queue explicitly to restart it:
Call qemu_flush_queued_packets when s->busy or s->rx_count is being
updated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-10-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop .can_receive and move the semantics into minimac2_rx, by returning
0.
That is once minimac2_rx returns 0, incoming packets will be queued
until the queue is explicitly flushed. We do this when s->regs[R_STATE0]
or s->regs[R_STATE1] is changed in minimac2_write.
Also drop the unused trace point.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-9-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The semantics of .can_receive requires us to flush the queue explicitly
when s->rx_enabled becomes true after it returns 0, but the packet being
queued is not meaningful since the guest hasn't activated the card.
Let's just drop the packet in this case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-8-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The BH will be scheduled when etsec->rx_buffer_len is becoming 0, which
is the condition of queuing.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-7-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When etsec_reset returns 0, peer would queue the packet as if
.can_receive returns false. Drop etsec_can_receive and let etsec_receive
carry the semantics.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-6-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
nic_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c63 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-4-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
pcnet_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c63 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The network mcf_fec driver emulated receive side method is returning a
result of 0 causing the network layer to disable receive for this emulated
device. This results in the guest only ever receiving one packet.
Fix the recieve side processing to return the number of bytes that we
passed back through to the guest.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-5-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Linux fec driver needs at least basic phy support to probe and work.
The current qemu mcf_fec emulation has no support for the reading or
writing of the MDIO lines to access an attached phy.
This code adds a very simple set of register results for a fixed phy
setup - very similar to that used on an m5208evb board. This is enough
to probe and identify an emulated attached phy.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-4-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
True is the default.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1435734647-8371-4-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
True is the default.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1435734647-8371-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Convert partially summed packets to be fully checksummed.
In case csum offloaded packet, vmxnet3 implementation always passes an
RxCompDesc with the "Checksum calculated and found correct" notification
to the OS. This emulates the observed ESXi behavior.
Therefore, if packet has the NEEDS_CSUM bit set, we must calculate and
place a fully computed checksum into the tcp/udp header. Otherwise, the
OS driver will receive a checksum-correct indication but with the actual
tcp/udp checksum field having just the pseudo header csum value.
If host OS performs forwarding, it will forward an incorrectly
checksummed packet.
Signed-off-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-id: 1436864116-19154-3-git-send-email-shmulik.ladkani@ravellosystems.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Separate RX packet protocol parsing out of 'vmxnet_rx_pkt_attach_data'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Message-id: 1436864116-19154-2-git-send-email-shmulik.ladkani@ravellosystems.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
commit da51a335 adds all queues in .realize(). But if the
guest doesn't support multiqueue, we forget to remove them. And
we cannot handle the ctrl vq corretly. The guest will hang.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This patch fixes network hang after "stop" then "cont", while network
packets keep arriving.
Tested both manually (tap, host pinging guest) and with Jason's qtest
series (plus his "[PATCH 2.4] socket: pass correct size in
net_socket_send()" fix).
As virtio_net_set_status is called when guest driver is setting status
byte and when vm state is changing, it is a good opportunity to flush
queued packets.
This is necessary because during vm stop the backend (e.g. tap) would
stop rx processing after .can_receive returns false, until the queue is
explicitly flushed or purged.
The other interesting condition in .can_receive, virtio_queue_ready(),
is handled by virtio_net_handle_rx() when guest kicks; the 3rd condition
is invalid queue index which doesn't need flushing.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 032a74a1c0
("virtio-net: byteswap virtio-net header") breaks any layout by
requiring out_sg[0].iov_len >= n->guest_hdr_len. Fixing this by
copying header to temporary buffer if swap is needed, and then use
this buffer as part of out_sg.
Fixes 032a74a1c0
("virtio-net: byteswap virtio-net header")
Cc: qemu-stable@nongnu.org
Cc: clg@fr.ibm.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This reverts commit 830d70db69.
The interface isn't fully backwards-compatible, which is bad.
Let's redo this properly after 2.4.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pc and virtio changes, bugfixes only.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVo6kaAAoJECgfDbjSjVRpEvcH/jiNHGHD+AzFSJ6+vcKH8MHY
GVyWxvnFimyusnv74c7nwTsRGjRycKCPFy8GN/ZX+VWpIpPwK9mysBQ97zM45xeM
T+w1eT4zXafZESr6coAaUu6AvPnVPmsx2im6j5LxBnyIzj41D7dydOM0dU/OHOSI
gUS2DlhqqRPqkB2LscIrkkCmiWpizxTACzZzrko+AuTZ6YVTOEWcnRps9gqR+MWF
o24uppNPIkkmKoWBbXEiTfTqy7rcWydCb/BiM0UMo2cTOeXESNiaQNbKL2ED8K5d
187sL9XCkBrImh4NOFMy4ZKsJ7Uy9zg+zpk03XbjMF+7S155Fcacp2ahDtuCoDA=
=DITH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio: fixes for 2.4
pc and virtio changes, bugfixes only.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jul 13 13:03:38 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
pc: fix reuse of pc-i440fx-2.4 in pc-i440fx-2.3
Revert "virtio-net: enable virtio 1.0"
virtio-pci: don't crash on illegal length
qdev: fix 64 bit properties
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit df91055db5.
This is because:
- vhost support virtio 1.0 now
- transport code (e.g virtio-pci) set this feature when modern is
enabled, setting this unconditionally will break disable-modern=on.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A few last minute PPC changes for 2.4:
- spapr: Update SLOF
- spapr: Fix a few bugs
- spapr: Preparation for hotplug
- spapr: Minor code cleanups
- linux-user: Add mftb handling
- kvm: Enable hugepage support with memory-backend-file
- mac99: Remove nonexistent interrupt pin (Mac OS 9 fix)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=+Uma
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2015-07-07
A few last minute PPC changes for 2.4:
- spapr: Update SLOF
- spapr: Fix a few bugs
- spapr: Preparation for hotplug
- spapr: Minor code cleanups
- linux-user: Add mftb handling
- kvm: Enable hugepage support with memory-backend-file
- mac99: Remove nonexistent interrupt pin (Mac OS 9 fix)
# gpg: Signature made Tue Jul 7 16:48:41 2015 BST using RSA key ID 03FEDC60
# gpg: Good signature from "Alexander Graf <agraf@suse.de>"
# gpg: aka "Alexander Graf <alex@csgraf.de>"
* remotes/agraf/tags/signed-ppc-for-upstream: (30 commits)
sPAPR: Clear stale MSIx table during EEH reset
sPAPR: Reenable EEH functionality on reboot
sPAPR: Don't enable EEH on emulated PCI devices
spapr-vty: Use TYPE_ definition instead of hardcoding
spapr_vty: lookup should only return valid VTY objects
spapr_pci: drop redundant args in spapr_[populate, create]_pci_child_dt
spapr_pci: populate ibm,loc-code
spapr_pci: enumerate and add PCI device tree
xics_kvm: Don't enable KVM_CAP_IRQ_XICS if already enabled
ppc: Update cpu_model in MachineState
spapr: Consolidate cpu init code into a routine
spapr: Reorganize CPU dt generation code
cpus: Add a macro to walk CPUs in reverse
spapr: Support ibm, lrdr-capacity device tree property
spapr: Consider max_cpus during xics initialization
Revert "hw/ppc/spapr_pci.c: Avoid functions not in glib 2.12 (g_hash_table_iter_*)"
spapr_iommu: translate sPAPRTCEAccess to IOMMUAccessFlags
spapr_iommu: drop erroneous check in h_put_tce_indirect()
spapr_pci: set device node unit address as hex
spapr_pci: encode class code including Prog IF register
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code for -machine pseries maintains a global sPAPREnvironment structure
which keeps track of general state information about the guest platform.
This predates the existence of the MachineState structure, but performs
basically the same function.
Now that we have the generic MachineState, fold sPAPREnvironment into
sPAPRMachineState, the pseries specific subclass of MachineState.
This is mostly a matter of search and replace, although a few places which
relied on the global spapr variable are changed to find the structure via
qdev_get_machine().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
For pkts copied to the CPU (to be processed by guest driver), mark the Rx
descriptor with flag "OFFLOAD_FWD" to indicate device has already forwarded
pkt. The guest driver will use this indicator to avoid duplicate
forwarding in the guest OS.
Examples include bcast/mcast/unknown ucast pkts flooded to bridged ports.
We want to avoid both the device and the guest bridge driver flooding these
pkts, which would result in duplicates pkts on the wire. Packet sampling,
such as sFlow, can also use this technique to mark pkts for the guest OS to
record but otherwise drop.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Message-id: 1435746792-41278-5-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435746792-41278-3-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Premature break in switch case block. This particular case (group L2 rewrite)
will be used for L2 LAG and L3 ECMP support, neither of which are enabled in
the guest driver at this time, but are under development.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435746792-41278-2-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 6e99c63 ("net/socket: Drop net_socket_can_send") changed the
semantics around .can_receive for sockets to now require the device to
flush queued pkts when transitioning to a .can_receive=true state. Rocker
device was not flushing the queue on .can_receive=true transition, so the
receiver was stuck.
But, turns out we really don't want any queuing at all on the port when the
port is disabled, otherwise when the port transitions to enabled, we'd
receive and forward stale pkts that really should have been dropped. So,
let's remove .can_receive so avoid queuing and drop the pkt in .receive if
the port is disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1435717553-36187-1-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When running ESXi under qemu there is an issue with the ESXi guest
discarding packets that are too short. The guest discards any packets
under the normal minimum length for an ethernet packet (60). This
results in odd behaviour where other hosts or VMs on other hosts can
communicate with the ESXi guest just fine (since there's a physical NIC
somewhere doing padding), but VMs on the host and the host itself cannot
because the ARP request packets are too small for the ESXi host to
accept.
Someone in the past thought this was worth fixing, and added code to the
vmxnet3 qemu emulation such that if it is receiving packets smaller than
60 bytes to pad the packet out to 60. Unfortunately this code is wrong
(or at least in the wrong place). It does so BEFORE before taking into
account the vnet_hdr at the front of the packet added by the tap device.
As a result, it might add padding, but it never adds enough.
Specifically it adds 10 less (the length of the vnet_hdr) than it needs
to.
The following (hopefully "obviously correct") patch simply swaps the
order of processing the vnet header and the padding. With this patch an
ESXi guest is able to communicate with the host or other local VMs.
Signed-off-by: Brian Kress <kressb@moose.net>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
e1000_can_receive() checks the link up status register bit. If the bit
is clear, packets will be queued and the peer may disable receive to
avoid wasting CPU reading packets that cannot be delivered. The queue
must be flushed once the link comes back up again.
This patch fixes broken e1000 receive with Mac OS X Snow Leopard guests
and tap networking. Flushing the queue invokes the async send callback,
which re-enables tap fd read.
Reported-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1435223885-12745-1-git-send-email-stefanha@redhat.com
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Most notably this includes virtio cross-endian patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVg+xdAAoJECgfDbjSjVRp6AAH/3ILznMtvJZjQ/WOjLEsL13M
+0cYEM1LI6LbLhqeruQVVcY9/hx61yHxZMoLkVg/I2po7F4HDNI2vo5Y7eGx+xN0
5rlcAw9/ZQ6SkCVmjN/VZfISW5mSqCaKH8gNzu8AigjsryJSj5iDXv1YJimwsF+5
cgCerhLIVvEkXmNj1ChwR+fz1IgFzJ8TRaZ0N2glxLyVjgKS57diqZF3Rbg2DdQl
BPbekbbtxesPgmKRvtarbhjx26TlnP1YShjhWA5r72gBNlqblLDycpaIGXr34b3a
sLIZjxzQtTEGcaGtkifMgazyK3rY3JmzOshD0onFOWY1r6Abxuj7eTZOEE6JQXk=
=tju/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci fixes, enhancements
Most notably this includes virtio cross-endian patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri Jun 19 11:18:05 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
vhost: enable vhost without without MSI-X
pci: Don't register a specialized 'config_write' if default behavior is intended
hw/core: rebase sysbus_get_fw_dev_path() to g_strdup_printf()
vhost_net: re-enable when cross endian
vhost-net: tell tap backend about the vnet endianness
tap: fix non-linux build
tap: add VNET_LE/VNET_BE operations
vhost: set vring endianness for legacy virtio
virtio: introduce virtio_legacy_is_cross_endian()
linux-headers: sync vhost.h
vhost-user: part of virtio
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We use vhostforce to enable vhost even if Guests don't have MSI-X
support and we fall back to QEMU virtio-net.
This gives a very small performance gain, but the disadvantage
is that guest now controls which virtio code is running
(qemu or vhost) so our attack surface is doubled.
This patch will enable vhost unconditionally whenever it's requested.
For compatibility, enable vhost when vhostforce is set, as well.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Few devices have their specialized 'config_write' methods which simply
call 'pci_default_write_config' followed by a 'msix_write_config' or
'msi_write_config' calls, using exact same arguments.
This is unnecessary as 'pci_default_write_config' already invokes
'msi_write_config' and 'msix_write_config'.
Also, since 'pci_default_write_config' is the default 'config_write'
handler, we can simply avoid the registration of these specialized
versions.
Cc: Leonid Shatz <leonid.shatz@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cross-endianness is now checked by the core vhost code.
revert 371df9f5e0 "vhost-net: disable when cross-endian"
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
[ added commit message, Greg Kurz <gkurz@linux.vnet.ibm.com> ]
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The default behaviour for TAP/MACVTAP is to consider vnet as native endian.
This patch handles the cases when this is not true:
- virtio 1.0: always little-endian
- legacy cross-endian
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJVetcwAAoJEJykq7OBq3PI+84IAMfkE0uCXdUbp3jZP9iVx68y
ZtHbhpnZle3bmVFBkgsF8vHWsMlxMZzr2PpAl02VXrrE6z0ScTz+GmVU2V89Y5nv
kn9DhAR4gcyKbKKgRtwjCLMoCfxsdaHTOJXfcHhsiqQP4PwdFkV6bQAymwcJegY/
ze5wKX8XqIML6yUCnhrN41pjt6NkIQoyRneLwX5ymeRLfWg23i9YOVU4Njmm9X52
kH7Xg0UuT6HTyyNER7iqwh61gQ33ETkfWd9UrHFGi7q70UJAr+cVXtzJjqnh08OU
BExph/lQfxXuivpiThvjZkPvMVqISyCrsIAXrwjhXnjqwz/3nt3i6zrfvPNNPG0=
=VdKf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/net-pull-request' into staging
# gpg: Signature made Fri Jun 12 13:57:20 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/net-pull-request:
qmp/hmp: add rocker device support
rocker: bring link up/down on PHY enable/disable
rocker: update tests using hw-derived interface names
rocker: Add support for phys name
iohandler: Change return type of qemu_set_fd_handler to "void"
event-notifier: Always return 0 for posix implementation
xen_backend: Remove unused error handling of qemu_set_fd_handler
oss: Remove unused error handling of qemu_set_fd_handler
alsaaudio: Remove unused error handling of qemu_set_fd_handler
main-loop: Drop qemu_set_fd_handler2
Change qemu_set_fd_handler2(..., NULL, ...) to qemu_set_fd_handler
tap: Drop tap_can_send
net/socket: Drop net_socket_can_send
netmap: Drop netmap_can_send
l2tpv3: Drop l2tpv3_can_send
stubs: Add qemu_set_fd_handler
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the OS driver enables/disables the port, go ahead and set the port's
link status to up/down in response to the change. This more closely
emulates real hardware when the PHY for the port is brought up/down
and the PHY negotiates carrier (link status) with link partner. In
the case of qemu, the virtual rocker device can't really do link
negotiation with the link partner as that requires signally over a
physical medium (the wire), so just pretend the negotiation was
successful and bring the link up when the port is enabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1433985681-56138-4-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add ROCKER_TLV_CMD_PORT_SETTINGS_PHYS_NAME to port settings. This attribute
exports the port name to the guest OS allowing it to name interfaces with
sensible defaults.
Mostly done by Scott for phys_id support; adapted to phys_name by David.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Message-id: 1433985681-56138-2-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Changes:
* improve dp8393x network card and rc4030 chipset emulation
* support misaligned R6 and MSA memory accesses
* support MIPS eXtended and Large Physical Addressing
* add Config5.FRE bit and ERETNC instruction (Config5.LLB)
* support ememsize on MALTA
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJVeppzAAoJEFIRjjwLKdprnk8H/1owSOreh0sMFbosvqlEhjXl
lvjjuprWMdX+8M1JlaDvTbw6+LDB3Rihp3A6/I9A0GFiZaORmPzg7efULAI1H6ST
0HfxMAO17eW+PJ3lvk0HidNDr01+RzTvwpizrHgQ9WJubJv0xREU+YG5yn1gPS4N
aMMTKCAQFDba7iQQLKXUYvLz76+xyzW4VIvHVLx/SU86yPg9T7CwLpppipR8+zY5
3BC4NUw/xLlS0LCYQGM8XmYgBiQ6lEAz/Y29bGlUg+LeYysjSgNSeoNbOs1M3kQp
X0Hn7b28I1CjM2wZQ9GkT/ig+jhMvw27motnAe8vKood4ytfcor+dCCS13sE8fg=
=F564
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20150612' into staging
MIPS patches 2015-06-12
Changes:
* improve dp8393x network card and rc4030 chipset emulation
* support misaligned R6 and MSA memory accesses
* support MIPS eXtended and Large Physical Addressing
* add Config5.FRE bit and ERETNC instruction (Config5.LLB)
* support ememsize on MALTA
# gpg: Signature made Fri Jun 12 09:38:11 2015 BST using RSA key ID 0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20150612: (29 commits)
target-mips: enable XPA and LPA features
target-mips: remove misleading comments in translate_init.c
target-mips: add MTHC0 and MFHC0 instructions
target-mips: add CP0.PageGrain.ELPA support
target-mips: support Page Frame Number Extension field
target-mips: extend selected CP0 registers to 64-bits in MIPS32
target-mips: correct MFC0 for CP0.EntryLo in MIPS64
net/dp8393x: fix hardware reset
net/dp8393x: correctly reset in_use field
net/dp8393x: add load/save support
net/dp8393x: add PROM to store MAC address
net/dp8393x: QOM'ify
net/dp8393x: use dp8393x_ prefix for all functions
net/dp8393x: do not use old_mmio accesses
net/dp8393x: always calculate proper checksums
dma/rc4030: convert to QOM
dma/rc4030: use trace events instead of custom logging
dma/rc4030: document register at offset 0x210
dma/rc4030: do not use old_mmio accesses
dma/rc4030: use AddressSpace and address_space_rw in users
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
Most notably this includes virtio 1 patches
Still not all devices converted, and not fully spec compliant,
so disabled by default.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVeXakAAoJECgfDbjSjVRpyFAH/AwSJhBbQOxtqS66INnzoLRJ
MWD3cP8tj0PzXsLx0cuPxdTboHH60alhSp+iLGv4NgNw15okY71bY2eLhewxS66W
a0wzVCaqeeD5GAoQaSOlqNLrhBodsKS62BWD9y0kK9rtMJfCW2C1JP8Mpue1XMuE
UC72tF4Q6wVdBD/kTD9DZW/23roFu0SuieFSjbQNNi1lInXtDv79UGX0xUHaXlal
+qCtRIy/wNZF0z5arNV/Skq7LKqYl7KZtTapZByy+q6vu0L8mOeXgJ9DLh666htB
NQJJ+VhsgBKPHmZqf8h4mPlvyp03rkr5dIGk7iB2o44GPaEJ/RjZ4wULjxWD12s=
=UY/0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, acpi, virtio
Most notably this includes virtio 1 patches
Still not all devices converted, and not fully spec compliant,
so disabled by default.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu Jun 11 12:53:08 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (42 commits)
i386/acpi-build: fix PXB workarounds for unsupported BIOSes
i386/acpi-build: more traditional _UID and _HID for PXB root buses
vhost-scsi: move qdev properties into vhost-scsi.c
virtio-9p-device: move qdev properties into virtio-9p-device.c
virtio-serial-bus: move qdev properties into virtio-serial-bus.c
virtio-rng: move qdev properties into virtio-rng.c
virtio-scsi: move qdev properties into virtio-scsi.c
virtio-net.h: Remove unsed DEFINE_VIRTIO_NET_PROPERTIES
virtio-net: move qdev properties into virtio-net.c
virtio-input: emulated devices [pci]
virtio-input: core code & base class [pci]
pci: add PCI_CLASS_INPUT_*
virtio-pci: fill VirtIOPCIRegions early.
virtio-pci: drop identical virtio_pci_cap
virtio-pci: move cap type to VirtIOPCIRegion
virtio-pci: move virtio_pci_add_mem_cap call to virtio_pci_modern_region_map
virtio-pci: add virtio_pci_modern_region_map()
virtio-pci: add virtio_pci_modern_regions_init()
virtio-pci: add struct VirtIOPCIRegion for virtio-1 regions
virtio-balloon: switch to virtio_add_feature
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Documentation is not clear of what happens when doing a hardware reset,
but firmware expect all registers to be zero unless specified otherwise.
This fixes reboot on MIPS Magnum.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Don't write more than the field width, which is always 16 bit.
Fixes network in NetBSD 5.1/arc
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Now that rc4030 internally uses an AddressSpace for DMA handling, make its root
memory region public. This is especially usefull for dp8393x netcard, which now
uses well known QEMU types and methods.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
As only one place in virtio-net.c uses DEFINE_VIRTIO_NET_FEATURES,
there is no need to expose it. Inline it into virtio-net.c to avoid
wrongly use.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make sure that all vhost interfaces use 64 bit features, as the virtio
core does, and make sure to use ULL everywhere possible to be on the
safe side.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Add VERSION_1 to list of features that we should
test at the backend.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
virtio-net (non-vhost) now should have everything in place to support
virtio 1.0: let's enable the feature bit for it.
Note that VIRTIO_F_VERSION_1 is technically a transport feature; once
every device is ready for virtio 1.0, we can move setting this
feature bit out of the individual devices.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>