I've found that FreeBSD AHCI driver doesn't work with AHCI hardware
emulation of QEMU 0.15.0. I believe the problem is on QEMU's side. As I
see, it clears port's Interrupt Enable register each time when reset of
any level happens. Is is reasonable for the global controller reset. It
is probably not good, but acceptable for FreeBSD driver for the port
hard reset. But it is IMO wrong for the device soft reset. None of real
hardware I know behaves that way.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Today, when notifying a VM state change with vm_state_notify(),
we pass a VMSTOP macro as the 'reason' argument. This is not ideal
because the VMSTOP macros tell why qemu stopped and not exactly
what the current VM state is.
One example to demonstrate this problem is that vm_start() calls
vm_state_notify() with reason=0, which turns out to be VMSTOP_USER.
This commit fixes that by replacing the VMSTOP macros with a proper
state type called RunState.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Member variable is_read is written, but never read
(contrary to its name). Remove it.
Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
change fails while the tray is locked by the guest. eject -f forces
it open and removes any media. Unfortunately, the tray closes again
instantly. Since the lock remains as it is, there is no way to insert
another medium unless the guest voluntarily unlocks.
Fix by leaving the tray open after monitor eject.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To let device models distinguish between eject and load.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models should be able to set it without an unclean include of
block_int.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Including it in device models is unclean, including it without a
reason adds insult to injury.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's convenience stuff for block device models, so block.h isn't the
ideal home either, but better than block_int.h.
Permits moving some #include "block_int.h" from device model .h into
.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Need to ask the device, so this requires new BlockDevOps member
is_tray_open().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's a confused mess (see previous commit). No users remain.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use a subsection, so that migration to older version still works,
provided the tray is closed and unlocked.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 6.40.2.6 specifies that START STOP UNIT succeeds when the drive
already has the requested state. cmd_start_stop_unit() fails when
asked to eject while the tray is open and locked. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Requires new BlockDevOps member is_medium_locked(). Implement for IDE
and SCSI CD-ROMs.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The device model knows best when to accept the guest's eject command.
No need to detour through the block layer.
bdrv_eject() can't fail anymore. Make it void.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState. Just like tray open/close
state, we should track it in the device models instead, because it's
device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 4be9762a changed bdrv_is_inserted() to fail when the tray is
open. Unfortunately, there are two different kinds of users, with
conflicting needs.
1. Device models using bdrv_eject(), currently ide-cd and scsi-cd.
They expect bdrv_is_inserted() to reflect the tray status. Commit
4be9762a makes them happy.
2. Code that wants to know whether a BlockDriverState has media, such
as find_image_format(), bdrv_flush_all(). Commit 4be9762a makes them
unhappy. In particular, it breaks flush on VM stop for media ejected
by the guest.
Revert the change to bdrv_is_inserted(). Check the tray status in the
device models instead.
Note on IDE: Since only ATAPI devices have a tray, and they don't
accept ATA commands since the recent commit "ide: Reject ATA commands
specific to drive kinds", checking in atapi.c suffices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState since commit 4be9762a. As
discussed in that commit's message, we should track it in the device
device models instead, because it's device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
"eject" is misleading; it means "eject" when start is clear, but
"load" when start is set. Rename to loej, because that's how MMC-5
calls it, in section 6.40.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ACS-2 Table B.2 explicitly prohibits ATAPI devices from implementing
WIN_RECAL, WIN_READ_EXT, WIN_READDMA_EXT, WIN_READ_NATIVE_MAX,
WIN_MULTREAD_EXT, WIN_WRITE, WIN_WRITE_ONCE, WIN_WRITE_EXT,
WIN_WRITEDMA_EXT, WIN_MULTWRITE_EXT, WIN_WRITE_VERIFY, WIN_VERIFY,
WIN_VERIFY_ONCE, WIN_VERIFY_EXT, WIN_SPECIFY, WIN_MULTREAD,
WIN_MULTWRITE, WIN_SETMULT, WIN_READDMA, WIN_READDMA_ONCE,
WIN_WRITEDMA, WIN_WRITEDMA_ONCE, WIN_FLUSH_CACHE_EXT. Restrict them
to IDE_HD and IDE_CFATA.
Same for CFA_WRITE_SECT_WO_ERASE, CFA_WRITE_MULTI_WO_ERASE. Restrict
them to IDE_CFATA, like the other CFA_ commands.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
No functional change.
It would be nice to have handler functions in the table, like commit
e1a064f9 did for ATAPI. Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Must set the ATAPI device signature, see ATA4 8.27.5.2 Outputs for
PACKET Command feature set devices, and ACS-2 7.36.6 Outputs for
PACKET feature set devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
pci_piix3_xen_ide_unplug() unplugs only disks, not CD-ROMs. It peeks
into the DriveInfo's BlockDriverState to distinguish between the two.
Unclean; use DriveInfo member media_cd, like xen_config_dev_blk().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drop WIN_SRST, it has the same value as WIN_DEVICE_RESET.
Drop unused WIN_RESTORE, it has the same value as WIN_RECAL.
Drop codes that are not implemented and long obsolete: WIN_READ_LONG,
WIN_READ_LONG_ONCE, WIN_WRITE_LONG, WIN_WRITE_LONG_ONCE, WIN_FORMAT
(all obsolete since ATA4), WIN_ACKMEDIACHANGE, WIN_POSTBOOT,
WIN_PREBOOT (obsolete since ATA3), WIN_WRITE_SAME (obsolete since
ATA3, code reused for something else in ACS2), WIN_IDENTIFY_DMA
(obsolete since ATA4).
Drop codes that are not implemented and vendor-specific:
EXABYTE_ENABLE_NEST, DISABLE_SEAGATE.
Drop WIN_INIT, it isn't implemented, its value used to be reserved,
and is used for something else since ATA8.
CFA_IDLEIMMEDIATE isn't specific to CFATA. ACS-2 shows it as a
defined command in ATA-1, -2 and -3. Rename to WIN_IDLEIMMEDIATE2.
Mark vendor specific, retired, and obsolete codes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Multiplexing callbacks complicates matters needlessly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For now, this just protects against programming errors like having the
same drive back multiple non-qdev devices, or untimely bdrv_delete().
Later commits will add other interesting uses.
While there, rename BlockDriverState member peer to dev, bdrv_attach()
to bdrv_attach_dev(), bdrv_detach() to bdrv_detach_dev(), and
bdrv_get_attached() to bdrv_get_attached_dev().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Most changes were made using these commands:
git grep -la '__attribute__((packed))'|xargs perl -pi -e 's/__attribute__\(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((packed))'|xargs perl -pi -e 's/__attribute__ \(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__((__packed__))'|xargs perl -pi -e 's/__attribute__\(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((__packed__))'|xargs perl -pi -e 's/__attribute__ \(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute((packed))'|xargs perl -pi -e 's/__attribute\(\(packed\)\)/QEMU_PACKED/'
Whitespace in linux-user/syscall_defs.h was fixed manually
to avoid warnings from scripts/checkpatch.pl.
Manual changes were also applied to hw/pc.c.
I did not fix indentation with tabs in block/vvfat.c.
The patch will show 4 errors with scripts/checkpatch.pl.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Decouple the I/O accounting from bdrv_aio_readv/writev/flush and
make the hardware models call directly into the accounting helpers.
This means:
- we do not count internal requests from image formats in addition
to guest originating I/O
- we do not double count I/O ops if the device model handles it
chunk wise
- we only account I/O once it actuall is done
- can extent I/O accounting to synchronous or coroutine I/O easily
- implement I/O latency tracking easily (see the next patch)
I've conveted the existing device model callers to the new model,
device models that are using synchronous I/O and weren't accounted
before haven't been updated yet. Also scsi hasn't been converted
to the end-to-end accounting as I want to defer that after the pending
scsi layer overhaul.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The unplug protocol is necessary to support PV drivers in the guest: the
drivers expect to be able to "unplug" emulated disks and nics before
initializing the Xen PV interfaces.
It is responsibility of the guest to make sure that the unplug is done
before the emulated devices or the PV interface start to be used.
We use pci_for_each_device to walk the PCI bus, identify the devices and
disks that we want to disable and dynamically unplug them.
Changes in v2:
- use PCI_CLASS constants;
- replace pci_unplug_device with qdev_unplug;
- do not import hw/ide/internal.h in xen_platform.c;
Changes in v3:
- introduce piix3-ide-xen, that support hot-unplug;
- move the unplug code to hw/ide/piix.c;
- just call qdev_unplug from xen_platform.c to unplug the IDE disks;
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Just in case there's still a way how a guest can read out buffers when it's not
supposed to, let's zero the buffers during initialisation so that we don't leak
information to the guest.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This fixes https://bugs.launchpad.net/qemu/+bug/786209:
When the DRQ_STAT bit is set, the IDE core permits both data reads
and data writes, regardless of whether the current transfer was
initiated as a read or write.
This potentially leaks uninitialized host memory into the guest,
if, before doing anything else to an IDE device, the guest begins a
write transaction (e.g. WIN_WRITE), but then *reads* from the IO
port instead of writing to it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Clearing the error status flag was missing for restarting flushes. Now that the
error status is separate from the BM status register, we can simply set it to 0
after restarting the request. This ensures that we never forget to clear a bit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add support for TRIM sub function of the data set management command,
and wire it up to the qemu discard infrastructure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace the is_read flag with a dma_cmd flag to allow the dma and
restart logic to handler other commands like TRIM.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When a failed PIO request caused the VM to stop, we still need to transfer the
PIO state even though DRQ=0 at this point.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When adding the werror=stop mode, some flags were added to s->status
which are used to determine what kind of operation should be restarted
when the VM is continued.
Unfortunately, it turns out that s->status is in fact a device register
and as such is visible to the guest (some of the abused bits are even
writable for the guest).
For migration we keep on using the old VMState field (renamed to
migration_compat_status) if the status register doesn't use any of the
previously abused bits. If it does, we use a subsection with a clean copy of
the status register.
The error status is always sent in a subsection if there is any error. It can't
use the old field because errors happen even without PCI.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. Unlike
DriveInfo, BlockDriverState should be about the host part only.
One of the remaining guest bits there is the "type hint". -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.
Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Fix regression of 667bb59: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The commit 667bb59d23
uses d->ahci.mem before it is initialized by
ahci_init(). Fix this by calling ahci_init() first thing
so that it's safe to use all fields in the ahci state struct.
Reported-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After the re-org of the atapi code, it might not be intuitive for a
reader of the code to understand why we're inserting a 'media not
present' state between cd changes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some commands are supposed to report a Not Ready Condition (i.e. they require
a medium to be present in order to execute successfully). Instead of
duplicating the check in each command implementation, let's add a flag and
check it before calling the command.
This patch only converts existing checks, it does not introduce new checks for
any of the other commands that can/should report a Not Ready Condition.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The disk size can only change when the medium is changed, and the change
callback takes care of updating s->nb_sectors in this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for a table of function pointers, factor each command out from
ide_atapi_cmd() into its own function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 Table F.1 lists errors that can be thrown for the TEST_UNIT_READY
command. Going from medium not ready to medium ready states is
communicated by throwing an error.
This adds the missing 'tray opened' event that we fail to report to
guests. After doing this, older Linux guests properly revalidate a disc
on the change command. HSM violation errors, which caused Linux guests
to do a soft-reset of the link, also go away:
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
res 01/60:00:00:00:00/00:00:00:00:00/a0 Emask 0x3 (HSM violation)
ata2.00: status: { ERR }
ata2: soft resetting link
ata2.00: configured for MWDMA2
ata2: EH complete
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement the 'media' sub-command of the GET_EVENT_STATUS_NOTIFICATION
command. This helps us report tray open, tray closed, no media, media
present states to the guest.
Newer Linux kernels (2.6.38+) rely on this command to revalidate discs
after media change.
This patch also sends out tray open/closed status to the guest driver
when requested e.g. via the CDROM_DRIVE_STATUS ioctl (thanks Markus).
Without such notification, the guest and qemu's tray open/close status
was frequently out of sync, causing installers like Anaconda detecting
no disc instead of tray open, confusing them terribly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle GET_EVENT_STATUS_NOTIFICATION's No Event Available response in a
generic way so that future additions to the code to handle other
response types is easier.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of using magic numbers, use structs that are more descriptive of
the fields being used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes the code more readable.
Also, there's a block like:
if () {
...
} else {
...
}
Split that into
if () {
...
return;
}
...
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After a media change, the only commands allowed from the guest were
REQUEST_SENSE and INQUIRY. The guest may also issue
GET_EVENT_STATUS_NOTIFICATION commands to get media
changed notification.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Table 629 of the MMC-5 spec mentions two different error conditions when
a CDROM eject is requested: a) while a disc is inserted and b) while a
disc is not inserted.
Ensure we return the appropriate error for the present condition of the
drive and disc status.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drivers are free to lock drives without any media present. Such a
condition should not result in an error condition.
See Table 341 in MMC-5 spec for details.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
factor out ide initialization to call drive_get(IF_IDE)
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* 'for-anthony' of git://github.com/bonzini/qemu:
remove qemu_get_clock
add a generic scaling mechanism for timers
change all other clock references to use nanosecond resolution accessors
change all rt_clock references to use millisecond resolution accessors
add more helper functions with explicit milli/nanosecond resolution
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes two things:
1) CHECK POWER MODE
The error return value wasn't always zero, so it would show up as
offline. Error is now explicitly set to zero.
2) SMART
The smart values that were returned were invalid and tools like skdump
would not recognize that the smart data was actually valid and would
dump weird output. The data has been fixed up and raw value support
was added. Tools like skdump and palimpsest work as expected.
Signed-off-by: Brian Wheeler <bdwheele@indiana.edu>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Nothing prevented IRQ sharing on the ISA bus in principle. Not all
boards supported this, neither each and every card nor driver and OS.
Still, there existed valid IRQ sharing scenarios, (at least) two of them
can also be found in QEMU: >2 PC UARTs and the PREP IDE buses.
So remove this artificial restriction from our ISA model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Define and use dedicated constants for vm_stop reasons, they actually
have nothing to do with the EXCP_* defines used so far. At this chance,
specify more detailed reasons so that VM state change handlers can
evaluate them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Different AHCI controllers have a different number of ports, so the core
shouldn't care about the amount of ports available.
This patch makes the number of ports available to the AHCI core runtime
configurable, allowing us to have multiple different AHCI implementations
with different amounts of ports.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ahci code was missing its soft reset functionality. This wasn't really an
issue for Linux guests, but Windows gets confused when the controller doesn't
reset when it tells it so.
Using this patch I can now successfully boot Windows 7 from AHCI using AHCI
enabled SeaBIOS.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The drive sends a d2h init fis on initialization. Usually, the guest doesn't
receive fises yet at that point though, so the delivery is deferred.
Let's reflect that by sending the init fis on fis receive enablement.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sebastian's patch already did a pretty good job at splitting up ICH-9
AHCI code and the AHCI core. We need some more though. Copyright was missing,
the lspci dump belongs to ICH-9, we don't need the AHCI core to have its
own qdev device duplicate.
So let's split them a bit more in this patch, making things easier to
read an understand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Due to popular request, this patch adds a license header to ahci.h
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are multiple ahci devices out there. The currently implemented ich-9
is only one of the many. So let's split that one out into a separate file
to stress the difference.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before commit 622b520f, index=12 meant bus=1,unit=5.
Since the commit, it means bus=0,unit=12. The drive is created, but
not the guest device. That's because the controllers we use with
if=scsi drives (lsi53c895a and esp) support only 7 units, and
scsi_bus_legacy_handle_cmdline() ignores drives with unit numbers
exceeding that limit.
Changing the mapping of index to bus, unit is a regression. Breaking
-drive invocations that used to work just makes it worse.
Revert the part of commit 622b520f that causes this, and clean up
some.
Note that the fix only affects if=scsi. You can still put more than 7
units on a SCSI bus with -device & friends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The len and is_write arguments to cpu_physical_memory_unmap() were
swapped. This patch changes calls to use the correct argument ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
