Switch the exynos4210_pwm code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-15-peter.maydell@linaro.org
Switch the ltick ptimer over to the ptimer transaction API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-14-peter.maydell@linaro.org
Switch the exynos MCT LFRC timers over to the ptimer transaction API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-13-peter.maydell@linaro.org
We want to switch the exynos MCT code away from bottom-half based ptimers to
the new transaction-based ptimer API. The MCT is complicated
and uses multiple different ptimers, so it's clearer to switch
it a piece at a time. Here we change over only the GFRC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-12-peter.maydell@linaro.org
Switch the digic-timer.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-11-peter.maydell@linaro.org
Switch the cmsdk-apb-timer code away from bottom-half based ptimers
to the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-10-peter.maydell@linaro.org
Switch the cmsdk-apb-dualtimer code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-9-peter.maydell@linaro.org
Switch the arm_mptimer.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-8-peter.maydell@linaro.org
Switch the allwinner-a10-pit code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-7-peter.maydell@linaro.org
Switch the arm_timer.c code away from bottom-half based ptimers
to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various arms of
arm_timer_write() that modify the ptimer state, and using the
new ptimer_init() function to create the timer.
Fixes: https://bugs.launchpad.net/qemu/+bug/1777777
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-5-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
Bottom halves and ptimers are malloced, but nothing in these
files is freeing memory allocated by instance_init. Since
these are sysctl devices that are never unrealized, just moving
the allocations to realize is enough to avoid the leak in
practice (and also to avoid upsetting asan when running
device-introspect-test).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The APB frequency can be calculated directly when needed from the
HPLL_PARAM and CLK_SEL register values. This removes useless state in
the model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-11-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First up: This is not the way the hardware behaves.
However, it helps resolve real-world problems with short periods being
used under Linux. Commit 4451d3f59f2a ("clocksource/drivers/fttmr010:
Fix set_next_event handler") in Linux fixed the timer driver to
correctly schedule the next event for the Aspeed controller, and in
combination with 5daa8212c08e ("ARM: dts: aspeed: Describe random number
device") Linux will now set a timer with a period as low as 1us.
Configuring a qemu timer with such a short period results in spending
time handling the interrupt in the model rather than executing guest
code, leading to noticeable "sticky" behaviour in the guest.
The behaviour of Linux is correct with respect to the hardware, so we
need to improve our handling under emulation. The approach chosen is to
provide back-pressure information by calculating an acceptable minimum
number of ticks to be set on the model. Under Linux an additional read
is added in the timer configuration path to detect back-pressure, which
will never occur on hardware. However if back-pressure is observed, the
driver alerts the clock event subsystem, which then performs its own
next event dilation via a config option - d1748302f70b ("clockevents:
Make minimum delay adjustments configurable")
A minimum period of 5us was experimentally determined on a Lenovo
T480s, which I've increased to 20us for "safety".
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190704055150.4899-1-clg@kaod.org
[clg: - changed the computation of min_ticks to be done each time the
timer value is reloaded. It removes the ordering issue of the
timer and scu reset handlers but is slightly slower ]
- introduced TIMER_MIN_NS
- introduced calculate_min_ticks() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
The reset notifiers are unreliable and recalculating the offsets
after boot causes problems with migration in cases where explicit
base times are set on the destination.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190724115823.4199-2-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The XLNX_ZYNQMP config is used in multiple subdirectories
(timer, intc). Move it to the root hw/Kconfig.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427141459.19728-2-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing migration/qemu-file-types.h
triggers a recompile of some 2600 out of 6600 objects (not counting
tests and objects that don't depend on qemu/osdep.h).
The culprit is again hw/hw.h, which supposedly includes it for
convenience.
Include migration/qemu-file-types.h only where it's needed. Touching
it now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The PL031 RTC tracks the difference between the guest RTC
and the host RTC using a tick_offset field. For migration,
however, we currently always migrate the offset between
the guest and the vm_clock, even if the RTC clock is not
the same as the vm_clock; this was an attempt to retain
migration backwards compatibility.
Unfortunately this results in the RTC behaving oddly across
a VM state save and restore -- since the VM clock stands still
across save-then-restore, regardless of how much real world
time has elapsed, the guest RTC ends up out of sync with the
host RTC in the restored VM.
Fix this by migrating the raw tick_offset. To retain migration
compatibility as far as possible, we have a new property
migrate-tick-offset; by default this is 'true' and we will
migrate the true tick offset in a new subsection; if the
incoming data has no subsection we fall back to the old
vm_clock-based offset information, so old->new migration
compatibility is preserved. For complete new->old migration
compatibility, the property is set to 'false' for 4.0 and
earlier machine types (this will only affect 'virt-4.0'
and below, as none of the other pl031-using machines are
versioned).
Reported-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20190709143912.28905-1-peter.maydell@linaro.org
Like most of the v7M memory mapped system registers, the systick
registers are accessible to privileged code only and user accesses
must generate a BusFault. We implement that for registers in
the NVIC proper already, but missed it for systick since we
implement it as a separate device. Correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190617175317.27557-6-peter.maydell@linaro.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-14-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
If the host decrements the counter register that results in a negative
delta. This is then passed to muldiv64 which only handles unsigned
numbers resulting in bogus results.
This fix ensures the delta being operated on is positive.
Test case: kexec a kernel using aspeed_timer and it will freeze on the
second bootup when the kernel initializes the timer. With this patch
that no longer happens and the timer appears to run OK.
Signed-off-by: Christian Svensson <bluecmd@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20190618165311.27066-12-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the match value exceeds reload then we don't want to include it in
calculations for the next event.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the datasheet:
This register stores the current status of counter #N. When timer
enable bit TMC30[N * b] is disabled, the reload register will be
loaded into this counter. When timer bit TMC30[N * b] is set, the
counter will start to decrement. CPU can update this register value
when enable bit is set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux kernel driver was updated in commit 4451d3f59f2a
("clocksource/drivers/fttmr010: Fix set_next_event handler) to fix an
issue observed on hardware:
> RELOAD register is loaded into COUNT register when the aspeed timer
> is enabled, which means the next event may be delayed because timer
> interrupt won't be generated until <0xFFFFFFFF - current_count +
> cycles>.
When running under Qemu, the system appeared "laggy". The guest is now
scheduling timer events too regularly, starving the host of CPU time.
This patch modifies the timer model to attempt to schedule the timer
expiry as the guest requests, but if we have missed the deadline we
re interrupt and try again, which allows the guest to catch up.
Provides expected behaviour with old and new guest code.
Fixes: c04bd47db6 ("hw/timer: Add ASPEED timer device model")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-8-clg@kaod.org
[clg: - merged a fix from Andrew Jeffery <andrew@aj.id.au>
"Fire interrupt on failure to meet deadline"
https://lists.ozlabs.org/pipermail/openbmc/2019-January/014641.html
- adapted commit log
- checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RTC is modeled to provide time and date functionality. It is
initialised at zero to match the hardware.
There is no modelling of the alarm functionality, which includes the IRQ
line. As there is no guest code to exercise this function that is
acceptable for now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417190641.26814-7-armbru@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Convert the debug printing in the PL031 device to use trace events,
and augment it to cover the interesting parts of device operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
A few targets don't emit RTC_CHANGE, we could restrict the event to
the tagets that do emit it.
Note: There is a lot more of events & commands that we could restrict
to capable targets, with the cost of some additional complexity, but
the benefit of added correctness and better introspection.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-19-armbru@redhat.com>
Move rtc-reset-reinjection and SEV in target.json and make them
conditional on TARGET_I386.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-10-armbru@redhat.com>
These files don't seem to do anything related to ISA directly, so
there is no need to include isa.h here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546615943-16274-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use DeviceClass rather than SysBusDeviceClass in
puv3_ost_class_init().
Cc: gxt@mprc.pku.edu.cn
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-19-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
grlib_gptimer_class_init().
Cc: chouteau@adacore.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-18-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
etraxfs_timer_class_init().
Cc: edgar.iglesias@gmail.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181130093852.20739-17-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code was converted to use sun4v_rtc_read() by mistake, fix
it.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181031001843.12892-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The UART and timer devices for the stm32f205 were being created
with memory regions that were too large. Use the size specified
in the chip datasheet.
The old sizes were so large that the devices would overlap with
each other in the SoC memory map, so this fixes a bug that
caused odd behavior and/or crashes when trying to set up multiple
UARTs.
Signed-off-by: Seth Kintigh <skintigh@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: rephrased commit message to follow our usual standard]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move from the legacy SysBusDevice::init method to using DeviceState::realize.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20181002212522.23303-4-f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----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=kPZX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-error-2018-10-22' into staging
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
In file included from /home/thuth/devel/qemu/hw/timer/aspeed_timer.c:16:
/home/thuth/devel/qemu/include/hw/misc/aspeed_scu.h:37:3: error:
redefinition of typedef 'AspeedSCUState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
} AspeedSCUState;
^
/home/thuth/devel/qemu/include/hw/timer/aspeed_timer.h:27:31: note:
previous definition is here
typedef struct AspeedSCUState AspeedSCUState;
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 'break' statements missing from a switch in the APB dual-timer
write function. Spotted by Coverity as CID 1395626 and 1395633.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180924123122.14549-1-peter.maydell@linaro.org
The generated qapi_event_send_FOO() take an Error ** argument. They
can't actually fail, because all they do with the argument is passing it
to functions that can't fail: the QObject output visitor, and the
@qmp_emit callback, which is either monitor_qapi_event_queue() or
event_test_emit().
Drop the argument, and pass &error_abort to the QObject output visitor
and @qmp_emit instead.
Suggested-by: Eric Blake <eblake@redhat.com>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815133747.25032-4-peterx@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message rewritten, update to qapi-code-gen.txt corrected]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
There is currently a funny problem with the "mc146818rtc" device:
1) Start QEMU like this:
qemu-system-ppc64 -M pseries -S
2) At the HMP monitor, enter "info qom-tree". Note that there is an
entry for "/rtc (spapr-rtc)".
3) Introspect the mc146818rtc device like this:
device_add mc146818rtc,help
4) Run "info qom-tree" again. The "/rtc" entry is gone now!
The rtc_finalize() function of the mc146818rtc device has two bugs: First,
it tries to remove a "rtc" property, while the rtc_realizefn() added a
"rtc-time" property instead. And second, it should have been done in an
unrealize function, not in a finalize function, to avoid that this causes
problems during introspection.
But since adding aliases to the global machine state should not be done
from a device's realize function anyway, let's rather fix this issue
by moving the creation of the alias to the code that creates the device
(and thus is run from the machine init functions instead), i.e. the
mc146818_rtc_init() function for most machines. The prep machines are
special, since the mc146818rtc device is created here in the realize
function of the i82378 device. Since we certainly don't want to add the
alias there, we add it to some code that is called from the ibm_40p_init()
machine init function instead.
Since the alias is now only created during the machine init, we can remove
the object_property_del() completely.
Fixes: 654a36d857
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1534419358-10932-5-git-send-email-thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mc146818rtc.c still contains some TABs. Replace them with spaces.
And while we're at it, also delete trailing whitespace in this file.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1534419358-10932-4-git-send-email-thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these are marked as "intentional/fix required" because they
just need adding a fall through comment. This is exactly what this
patch does, except for target/mips/translate.c where it is easier to
duplicate the code, and hw/audio/sb16.c where I consulted the DOSBox
sources and decide to just remove the LOG_UNIMP before the fallthrough.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the m48t59 device away from using old_mmio MemoryRegionOps
accessors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20180802180602.22047-1-peter.maydell@linaro.org
If the CMSDK APB timer is set up with a zero RELOAD value
then it will count down to zero, fire once and then stay
at zero. From the point of view of the ptimer system, the
timer is disabled; but the enable bit in the CTRL register
is still set and if the guest subsequently writes to the
RELOAD or VALUE registers this should cause the timer to
start counting down again.
Add code to the write paths for RELOAD and VALUE so that
we correctly restart the timer in this situation.
Conversely, if the new RELOAD and VALUE are both zero,
we should stop the ptimer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-5-peter.maydell@linaro.org
The CMSDK APB timer is currently always configured as periodic timer.
This results in the following messages when trying to boot Linux.
Timer with delta zero, disabling
If the timer limit set with the RELOAD command is 0, the timer
needs to be enabled as one-shot timer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CMSDK timer interrupt triggers when the counter goes from 1 to 0,
so we want to trigger immediately, rather than waiting for a
clock cycle. Drop the incorrect NO_IMMEDIATE_TRIGGER setting.
We also do not want to get an interrupt if the guest sets the
counter directly to zero, so use the new TRIGGER_ONLY_ON_DECREMENT
policy.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-3-peter.maydell@linaro.org
Basic emulation of the M41T80 serial (I2C) RTC chip. Only getting time
of day is implemented. Setting time and RTC alarm are not supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606152128.449-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When compiling with NVRAM_PRINTF enabled, gcc currently bails out with:
CC hw/timer/m48t59.o
CC hw/timer/m48t59-isa.o
hw/timer/m48t59.c: In function ‘NVRAM_writeb’:
hw/timer/m48t59.c:460:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘hwaddr’ [-Werror=format=]
NVRAM_PRINTF("%s: 0x%08x => 0x%08x\n", __func__, addr, val);
^
hw/timer/m48t59.c:460:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘uint64_t’ [-Werror=format=]
hw/timer/m48t59.c: In function ‘NVRAM_readb’:
hw/timer/m48t59.c:492:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘hwaddr’ [-Werror=format=]
NVRAM_PRINTF("%s: 0x%08x <= 0x%08x\n", __func__, addr, retval);
Fix it by using the correct format strings and while we're at it,
also change the definition of NVRAM_PRINTF so that this can not
bit-rot so easily again.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
commit 1d3e65aa7a ("hw/timer: Add value matching support to
aspeed_timer") increased the vmstate version of aspeed.timer because
the state had changed, but it also bumped the version of the
VMSTATE_STRUCT_ARRAY under the aspeed.timerctrl which did not need to.
Change back this version to fix migration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180423101433.17759-1-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
Allow the guest to determine the time set from the QEMU command line.
This includes adding a trace event to debug the new time.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial commit of the ZynqMP RTC device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJafZmjAAoJEDhwtADrkYZTuvkP/i8gYzquYW/8u0XiGjQdi0VM
cZzxqLe9DSxfjRO9p0D11uLQmw3js8z60mi++1NOhtYTn4P/htsgXLrrxrLS8U0I
b+mD6LeqGN2miCKWy4X/w52S0krW05ROJMb/s+OQP7aJu/OA+t6QXM6jzIPOnFa+
GrxFesOizvjLVONvmI8nbUKXayJ77rB8ctsuCjmbMO1XkxMLPWLchduswFH7ywbL
ZJwUK3v1x+R0Apvy7y4f8e6aamreABtAjuD53zoS1PmLfZ4dvgYVJkhimIGsVjpA
8AGCbazsIWl7YLJ2dghXaVE2gwV3LrwTPhoF0YeSjrJ2f4TE7NPCaPZW3C9yTtQC
YEiD4cG5HNE7HhBRIImmTvOGU7sSmYwJQ4+5yGKtJGlBGRSbYP2upWf3nEsOnGPx
TkdcsEPQHEP/YuJlZpO4jfdUiBAQsbmyY3xnMvdpfhDJRGSB7UwQ1xTgmjIXOr15
6Zv4NaWB0JInGhoEAra4Jdld3fJ0Nh+XAXITAPogppipvxmIYz9AxZTjhu0cQWX6
dDvk3FSOuC8Y+r/6UxQkAwCNAld+GilAABgHtXQjx8b8ySlE98EKuvcmPaH4pemC
K0YoRF32rIoDLbh6xg++ior7+eABrk9STlqCI/3SSEgDr0loTyXnI5KBBNoz+Jjw
AU2c5RYvNOqEGT42bL/C
=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HPET saves its state by calculating the current time and recovers timer
offset using this calculated value. But these calculations include
divisions and multiplications. Therefore the timer state cannot be recovered
precise enough.
This patch introduces saving of the original value of the offset to
preserve the determinism of the timer.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Maria Klimushenkova <maria.klimushenkova@ispras.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
--
v3: Added compat property for correct migration.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180103224208.30291-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
and remove the old i386/pc dependency
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Modelled System Timer in Microsemi's Smartfusion2 Soc.
Timer has two 32bit down counters and two interrupts.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't use the old_mmio struct in memory region ops.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-5-git-send-email-peter.maydell@linaro.org
Don't use the old_mmio in the memory region ops struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-4-git-send-email-peter.maydell@linaro.org
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
In some cases, the guest can observe the wrong ordering of UIP and
interrupts. This can happen if the VCPU exit is timed like this:
iothread VCPU
... wait for interrupt ...
t-100ns read register A
t wake up, take BQL
t+100ns update_in_progress
return false
return UIP=0
trigger interrupt
The interrupt is late; the VCPU expected the falling edge of UIP to
happen after the interrupt. update_in_progress is already trying to
cover this case by latching UIP if the timer is going to fire soon,
and the fix is documented in the commit message for commit 56038ef623
("RTC: Update the RTC clock only when reading it", 2012-09-10). It
cannot be tested with qtest, because its timing of interrupts vs. reads
is exact.
However, the implementation was incorrect because UIP cmos_ioport_read
cleared register A instead of leaving that to rtc_update_timer. Fixing
the implementation of cmos_ioport_read to match the commit message,
however, breaks the "uip-stuck" test case from the previous patch.
To fix it, skip update timer optimizations if UIP has been latched.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement a model of the simple timer device found in the CMSDK.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-5-git-send-email-peter.maydell@linaro.org
When a timer is enabled before a reload value is set, the controller
waits for a reload value to be set before starting decrementing. This
fix tries to cover that case by changing the timer expiry only when
a reload value is valid.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1496739312-32304-1-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove defines not used anywhere.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Statements under 'case' were in some places wrongly indented bringing
confusion and making the code less readable. Remove also few unneeded
blank lines. No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix checkpatch errors:
1. ERROR: spaces required around that '+' (ctx:VxV)
2. ERROR: spaces required around that '&' (ctx:VxV)
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It tests the accuracy of rtc periodic timer which is recently
improved & fixed by commit 7ffcb539a3 ("mc146818rtc: precisely count
the clock for periodic timer", 2017-05-19).
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170527025301.23499-1-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a function, rtc_policy_slew_deliver_irq(), which delivers
irq if LOST_TICK_POLICY_SLEW is used, as which is only supported on
x86, other platforms call it will trigger a assert
After that, we can move the x86 specific code to the common place
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-6-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the code purely depends on LOST_TICK_POLICY_SLEW, we can simply
drop '#ifdef TARGET_I386' as only x86 can enable this tick policy
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-5-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Any tick policy specified on other platforms rather on TARGET_I386
will fall back to LOST_TICK_POLICY_DISCARD silently, this patch makes
sure only TARGET_I386 can enable LOST_TICK_POLICY_SLEW
After that, we can enable LOST_TICK_POLICY_SLEW in the common code
which need not use '#ifdef TARGET_I386' to make these code be x86
specific anymore
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-4-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two issues in current code:
1) If the period is changed by re-configuring RegA, the coalesced
irq will be scaled to reflect the new period, however, it
calculates the new interrupt number like this:
s->irq_coalesced = (s->irq_coalesced * s->period) / period;
There are some clocks will be lost if they are not enough to
be squeezed to a single new period that will cause the VM clock
slower
In order to fix the issue, we calculate the interrupt window
based on the precise clock rather than period, then the clocks
lost during period is scaled can be compensated properly
2) If periodic_timer_update() is called due to RegA reconfiguration,
i.e, the period is updated, current time is not the start point
for the next periodic timer, instead, which should start from the
last interrupt, otherwise, the clock in VM will become slow
This patch takes the clocks from last interrupt to current clock
into account and compensates the clocks for the next interrupt,
especially if a complete interrupt was lost in this window, the
time can be caught up by LOST_TICK_POLICY_SLEW
Signed-off-by: Tai Yunfang <yunfangtai@tencent.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-3-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the timer is updated whenever RegA or RegB is written
even if the periodic timer related configuration is not changed
This patch optimizes it slightly to make the update happen only
if its period or enable-status is changed, also later patches are
depend on this optimization
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-2-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use sizeof instead of ARRAY_SIZE, fixing -Wmemset-elt-size with recent
GCC versions.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
rename slavio_timer_init1 to slavio_timer_init and assign
it to slavio_timer_info.instance_init, then we drop the
SysBusDeviceClass::init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
* assign DeviceClass::vmsd instead of using vmstate_register function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
hpet needs to be mapped and wired by the board code and won't
work with -device. Remove the user_creatable flag from the device
class.
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-18-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
commit 33cd52b5d7 unset
cannot_instantiate_with_device_add_yet in TYPE_SYSBUS, making all
sysbus devices appear on "-device help" and lack the "no-user"
flag in "info qdm".
To fix this, we can set user_creatable=false by default on
TYPE_SYS_BUS_DEVICE, but this requires setting
user_creatable=true explicitly on the sysbus devices that
actually work with -device.
Fortunately today we have just a few has_dynamic_sysbus=1
machines: virt, pc-q35-*, ppce500, and spapr.
virt, ppce500, and spapr have extra checks to ensure just a few
device types can be instantiated:
* virt supports only TYPE_VFIO_CALXEDA_XGMAC, TYPE_VFIO_AMD_XGBE.
* ppce500 supports only TYPE_ETSEC_COMMON.
* spapr supports only TYPE_SPAPR_PCI_HOST_BRIDGE.
This patch sets user_creatable=true explicitly on those 4 device
classes.
Now, the more complex cases:
pc-q35-*: q35 has no sysbus device whitelist yet (which is a
separate bug). We are in the process of fixing it and building a
sysbus whitelist on q35, but in the meantime we can fix the
"-device help" and "info qdm" bugs mentioned above. Also, despite
not being strictly necessary for fixing the q35 bug, reducing the
list of user_creatable=true devices will help us be more
confident when building the q35 whitelist.
xen: We also have a hack at xen_set_dynamic_sysbus(), that sets
has_dynamic_sysbus=true at runtime when using the Xen
accelerator. This hack is only used to allow xen-backend devices
to be dynamically plugged/unplugged.
This means today we can use -device with the following 22 device
types, that are the ones compiled into the qemu-system-x86_64 and
qemu-system-i386 binaries:
* allwinner-ahci
* amd-iommu
* cfi.pflash01
* esp
* fw_cfg_io
* fw_cfg_mem
* generic-sdhci
* hpet
* intel-iommu
* ioapic
* isabus-bridge
* kvmclock
* kvm-ioapic
* kvmvapic
* SUNW,fdtwo
* sysbus-ahci
* sysbus-fdc
* sysbus-ohci
* unimplemented-device
* virtio-mmio
* xen-backend
* xen-sysdev
This patch adds user_creatable=true explicitly to those devices,
temporarily, just to keep 100% compatibility with existing
behavior of q35. Subsequent patches will remove
user_creatable=true from the devices that are really not meant to
user-creatable on any machine, and remove the FIXME comment from
the ones that are really supposed to be user-creatable. This is
being done in separate patches because we still don't have an
obvious list of devices that will be whitelisted by q35, and I
would like to get each device reviewed individually.
Cc: Alexander Graf <agraf@suse.de>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-block@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: sstabellini@kernel.org
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-3-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[ehabkost: Small changes at sysbus_device_class_init() comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
qemu_log_mask() and error_report() are preferred over fprintf() for
logging errors. Also remove square brackets [] and additional new line
characters in printed messages.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170313184750.429-2-krzk@kernel.org
[PMM: wrapped long line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The i.MX timer device can be reset by writing to the SWR bit
of the CR register. This has to behave differently from hard
(power-on) reset because it does not reset all of the bits
in the CR register.
We were incorrectly implementing soft reset and hard reset
the same way, and in addition had a logic error which meant
that we were clearing the bits that soft-reset is supposed
to preserve and not touching the bits that soft-reset clears.
This was not correct behaviour for either kind of reset.
Separate out the soft reset and hard reset code paths, and
correct the handling of reset of the CR register so that it
is correct in both cases.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
[PMM: rephrased commit message, spacing on operators;
use bool rather than int for is_soft_reset]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a new function mips_gictimer_get_freq() which returns the
frequency at which a GIC timer will count. This will be useful for
boards which perform setup based upon this frequency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The m48t59 device supports both ISA and direct sysbus attached versions of
the device in the one .c file. This can be awkward for some embedded
machine types which need the sysbus M48T59, but don't want to pull in the
ISA bus code and its other dependencies.
Therefore, this patch splits out the code for the ISA attached M48T59 into
its own C file. It will be built when both CONFIG_M48T59 and
CONFIG_ISA_BUS are enabled.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This patch disables the update of the periodic timer of mc146818rtc
in record/replay mode. State of this timer is saved and therefore does
not need to be updated in record/replay mode.
Read of RTC breaks the replay because all rtc reads have to be the same
as in record mode.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071730.4572.41874.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the Altera timer model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-6-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
reset mc146818rtc device when RESET event happens.
Fix the problem:
1. Guest boot the second cpu, set CMOS_RESET_CODE 0x0a to protect selfboot;
2. VM being reset by others, hmp_system_reset;
3. seabios resume check the CMOS_RESET_CODE, if 0x0a, jump to the BDA
resume execution by jump via 40h:0067h;
4. Guest halt;
Signed-off-by: hangaohuai <hangaohuai@huawei.com>
Message-Id: <20161219060336.10176-1-hangaohuai@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a NULL check for i2c slave init callbacks, so that we no longer
need to implement empty init functions.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20161202054617.6749-4-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: squashed in later tweak from Alistair to if() phrasing]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The STM32F2XX Timer emulator uses a 16 bit prescaler value to
limit the timer clock rate. It does that by dividing the timer
frequency. If the prescaler 's->tim_psc' was set to be UINT_MAX,
it'd lead to divide by zero error. Limit prescaler value to 16
bits to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476800269-31902-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM A9MP processor has a peripheral timer with an auto-increment
register, which holds an increment step value. A user could set
this value to zero. When auto-increment control bit is enabled,
it leads to an infinite loop in 'a9_gtimer_update' while
updating comparator value. Remove this loop incrementing the
comparator value.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476733226-11635-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If correctly configured allow the STM32F2xx timer to print
out the PWM duty cycle information.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: cdb59039a25e061615713a94b40797baa12ea9f9.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu tracks guest time based on vector [base_rtc, last_update], in which
last_update stands for a monotonic tick which is actually uptime of the
host.
according to rtc implementation codes of recent releases and upstream,
after
migration, the time base vector [base_rtc, last_update] isn't updated to
coordinate with the destionation host, ie. qemu doesnt update last_update
to
uptime of the destination host.
what problem have we got because of this bug? after migration, guest time
may
jump back to several days ago, that will make some critical business
applications,
such as lotus notes, malfunction.
this patch is trying to fix the problem. first, when vmsave in progress,
we
rtc_update_time to refresh time stamp in cmos array, then during
vmrestore,
we rtc_set_time to update qemu base_rtc and last_update variable according
to time
stamp in cmos array.
Signed-off-by: Junlian Bell <zhongjun@sangfor.com.cn>
Message-Id: <20160926124101.2364-1-zhongjun@sangfor.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'char const' means the same thing as 'const char', but we
use the former in only a handful of places and we use the
latter over six thousand times. Switch the imx reg_name()
functions to bring them in line with everything else.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
