After an SDLC "Enter hunt" command has been sent the STATUS_SYNC bit should remain
high until the flag byte has been detected. Whilst the ESCC device doesn't yet
implement SDLC mode, without this change the active low STATUS_SYNC is constantly
asserted causing the MacOS OpenTransport extension to hang on startup as it thinks
it is constantly receiving LocalTalk responses during its initial negotiation
phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This removes duplication of the internal device state initialisation between
device reset and soft reset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that register values at reset are handled elsewhere for all of device reset,
soft reset and hard reset, escc_reset_chn() only needs to handle initialisation
of internal device state.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The hardware reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
hardware reset and implement the default values using the existing soft reset code
with the additional changes listed in the table in the "Z85C30 Reset" section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The software reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
soft reset and implement the default values listed in the table in the "Z85C30 Reset"
section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new hardware reset function is to be called for both channels when the
hardware reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a hard reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new software reset function is to be called when the appropriate channel
software reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a soft reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to ensure that a device reset always returns the ESCC to a known state.
Note that this is currently redundant with the same code in escc_reset_chn()
but that will change shortly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Also fix a couple of spelling mistakes in comments.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum.
By using the enum in the IOEventHandler typedef we:
- make the IOEventHandler type more explicit (this handler
process out-of-band information, while the IOReadHandler
is in-band),
- help static code analyzers.
This patch was produced with the following spatch script:
@match@
expression backend, opaque, context, set_open;
identifier fd_can_read, fd_read, fd_event, be_change;
@@
qemu_chr_fe_set_handlers(backend, fd_can_read, fd_read, fd_event,
be_change, opaque, context, set_open);
@depends on match@
identifier opaque, event;
identifier match.fd_event;
@@
static
-void fd_event(void *opaque, int event)
+void fd_event(void *opaque, QEMUChrEvent event)
{
...
}
Then the typedef was modified manually in
include/chardev/char-fe.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On Sparc and PowerMac, the bit 0 of the address selects the register
type (control or data) and bit 1 selects the channel (B or A).
On m68k Macintosh and NeXTcube, the bit 0 selects the channel and
bit 1 the register type.
This patch introduces a new parameter (bit_swap) to the device interface
to indicate bits usage must be swapped between registers and channels.
For the moment all the machines use the bit 0, but this change will be
needed to emulate the Quadra 800 or NeXTcube machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
[thh: added NeXTcube to the patch description]
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-5-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The SCC/ESCC will briefly stop asserting an interrupt when the
transmit FIFO is filled.
This code doesn't model the transmit FIFO/shift register so the
pending transmit interrupt is never deasserted which means that an
edge-triggered interrupt controller will never see the low-to-high
transition it needs to raise another interrupt. The practical
consequence of this is that guest firmware with an interrupt service
routine for the ESCC that does not send all of the data it has
immediately will stop sending data if the following sequence of
events occurs:
1. Disable processor interrupts
2. Write a character to the ESCC
3. Add additional characters to a buffer which is drained by the ISR
4. Enable processor interrupts
In this case, the first character will be sent, the interrupt will
fire and the ISR will output the second character. Since the pending
transmit interrupt remains asserted, no additional interrupts will
ever fire.
This behavior was triggered by firmware for an embedded system with a
Z85C30 which necessitated this patch.
This patch fixes that situation by explicitly lowering the IRQ when a
character is written to the buffer and no other interrupts are currently
pending.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Move necessary stuff in escc.h and update type names.
Remove slavio_serial_ms_kbd_init().
Fix code style problems reported by checkpatch.pl
Update mac_newworld, mac_oldworld and sun4m to use directly the
QDEV interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace the qcode_to_keycode table with automatically
generated tables.
Missing entries in qcode_to_keycode now fixed:
- Q_KEY_CODE_KP_COMMA -> 0x2d
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-3-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The right alt key (alt_r aka KEY_RIGHTALT) is used for AltGr.
The altgr and altgr_r keys simply don't exist. Drop them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170727104720.30061-1-kraxel@redhat.com
frontends should avoid accessing CharDriver struct where possible
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-6-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move all the frontend struct and methods to a seperate unit. This avoids
accidentally mixing backend and frontend calls, and helps with readabilty.
Make qemu_chr_replay() a macro shared by both char and char-fe.
Export qemu_chr_write(), and use a macro for qemu_chr_write_all()
(nb: yes, CharBackend is for char frontend :)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
So they are all in one place. The following patch will move serial &
parallel declarations to the respective headers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu_chr_fe_write method will return -1 on EAGAIN if the
chardev backend write would block. Almost no callers of the
qemu_chr_fe_write() method check the return value, instead
blindly assuming data was successfully sent. In most cases
this will lead to silent data loss on interactive consoles,
but in some cases (eg RNG EGD) it'll just cause corruption
of the protocol being spoken.
We unfortunately can't fix the virtio-console code, due to
a bug in the Linux guest drivers, which would cause the
entire Linux kernel to hang if we delay processing of the
incoming data in any way. Fixing this requires first fixing
the guest driver to not hold spinlocks while writing to the
hvc device backend.
Fixes bug: https://bugs.launchpad.net/qemu/+bug/1586756
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473170165-540-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit e7c9136977
(hw/char: QOM'ify escc.c) cause qemu-system-ppc/ppc64
OpenBIOS to freeze on startup, this commit fix it.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <1464767898-30526-1-git-send-email-zxq_yx_007@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Drop the old SysBus init function and use instance_init
* Call qemu_chr_add_handlers in the realize callback
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-2-git-send-email-zxq_yx_007@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simple unions were carrying a special case that hid their 'data'
QMP member from the resulting C struct, via the hack method
QAPISchemaObjectTypeVariant.simple_union_type(). But by using
the work we started by unboxing flat union and alternate
branches, coupled with the ability to visit the members of an
implicit type, we can now expose the simple union's implicit
type in qapi-types.h:
| struct q_obj_ImageInfoSpecificQCow2_wrapper {
| ImageInfoSpecificQCow2 *data;
| };
|
| struct q_obj_ImageInfoSpecificVmdk_wrapper {
| ImageInfoSpecificVmdk *data;
| };
...
| struct ImageInfoSpecific {
| ImageInfoSpecificKind type;
| union { /* union tag is @type */
| void *data;
|- ImageInfoSpecificQCow2 *qcow2;
|- ImageInfoSpecificVmdk *vmdk;
|+ q_obj_ImageInfoSpecificQCow2_wrapper qcow2;
|+ q_obj_ImageInfoSpecificVmdk_wrapper vmdk;
| } u;
| };
Doing this removes asymmetry between QAPI's QMP side and its
C side (both sides now expose 'data'), and means that the
treatment of a simple union as sugar for a flat union is now
equivalent in both languages (previously the two approaches used
a different layer of dereferencing, where the simple union could
be converted to a flat union with equivalent C layout but
different {} on the wire, or to an equivalent QMP wire form
but with different C representation). Using the implicit type
also lets us get rid of the simple_union_type() hack.
Of course, now all clients of simple unions have to adjust from
using su->u.member to using su->u.member.data; while this touches
a number of files in the tree, some earlier cleanup patches
helped minimize the change to the initialization of a temporary
variable rather than every single member access. The generated
qapi-visit.c code is also affected by the layout change:
|@@ -7393,10 +7393,10 @@ void visit_type_ImageInfoSpecific_member
| }
| switch (obj->type) {
| case IMAGE_INFO_SPECIFIC_KIND_QCOW2:
|- visit_type_ImageInfoSpecificQCow2(v, "data", &obj->u.qcow2, &err);
|+ visit_type_q_obj_ImageInfoSpecificQCow2_wrapper_members(v, &obj->u.qcow2, &err);
| break;
| case IMAGE_INFO_SPECIFIC_KIND_VMDK:
|- visit_type_ImageInfoSpecificVmdk(v, "data", &obj->u.vmdk, &err);
|+ visit_type_q_obj_ImageInfoSpecificVmdk_wrapper_members(v, &obj->u.vmdk, &err);
| break;
| default:
| abort();
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1458254921-17042-13-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
An upcoming patch will alter how simple unions, like InputEvent, are
laid out, which will impact all lines of the form 'evt->u.XXX'
(expanding it to the longer 'evt->u.XXX.data'). For better
legibility in that patch, and less need for line wrapping, it's better
to use a temporary variable to reduce the effect of a layout change to
just the variable initializations, rather than every reference within
an InputEvent.
There was one instance in hid.c:hid_pointer_event() where the code
was referring to evt->u.rel inside the case label where evt->u.abs
is the correct name; thankfully, both members of the union have the
same type, so it happened to work, but it is now cleaner.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1457021813-10704-8-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Now that we guarantee the user doesn't have any enum values
beginning with a single underscore, we can use that for our
own purposes. Renaming ENUM_MAX to ENUM__MAX makes it obvious
that the sentinel is generated.
This patch was mostly generated by applying a temporary patch:
|diff --git a/scripts/qapi.py b/scripts/qapi.py
|index e6d014b..b862ec9 100644
|--- a/scripts/qapi.py
|+++ b/scripts/qapi.py
|@@ -1570,6 +1570,7 @@ const char *const %(c_name)s_lookup[] = {
| max_index = c_enum_const(name, 'MAX', prefix)
| ret += mcgen('''
| [%(max_index)s] = NULL,
|+// %(max_index)s
| };
| ''',
| max_index=max_index)
then running:
$ cat qapi-{types,event}.c tests/test-qapi-types.c |
sed -n 's,^// \(.*\)MAX,s|\1MAX|\1_MAX|g,p' > list
$ git grep -l _MAX | xargs sed -i -f list
The only things not generated are the changes in scripts/qapi.py.
Rejecting enum members named 'MAX' is now useless, and will be dropped
in the next patch.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1447836791-369-23-git-send-email-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
[Rebased to current master, commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for input-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-20-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
ESCC is a serial port controller, so add it
to the input category.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Nasty 0xe0 logic is gone. We map through QKeyCode now, giving us a
nice, readable mapping table.
Quick smoke test in OpenFirmware looks ok. Careful check from arch
maintainers would be very nice, especially on the capslock and numlock
logic. I'm not fully sure whenever I got it translated correctly and
also what it is supposed to do in the first place ...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We are using the same struct name for two devices. 8250 is widespread
enough that this causes some confusion, rename the other instance.
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
