Intel(R) VT-d 3.0 spec introduces scalable mode address translation to
replace extended context mode. This patch extends current emulator to
support Scalable Mode which includes root table, context table and new
pasid table format change. Now intel_iommu emulates both legacy mode
and scalable mode (with legacy-equivalent capability set).
The key points are below:
1. Extend root table operations to support both legacy mode and scalable
mode.
2. Extend context table operations to support both legacy mode and
scalable mode.
3. Add pasid tabled operations to support scalable mode.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to contribute much to refine the whole commit.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-2-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Split vhost_user_read(), so only header can be read with
vhost_user_read_header().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190308140454.32437-8-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20190308140454.32437-6-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Take a VhostUserState* that can be pre-allocated, and initialize it
with the associated chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
Message-Id: <20190308140454.32437-4-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Prior to f6deb6d9 "virtio-balloon: Remove unnecessary MADV_WILLNEED on
deflate", the balloon device issued an madvise() MADV_WILLNEED on
pages removed from the balloon. That would hint to the host kernel
that the pages were likely to be needed by the guest in the near
future.
It's unclear if this is actually valuable or not, and so f6deb6d9
removed this, essentially ignoring balloon deflate requests. However,
concerns have been raised that this might cause a performance
regression by causing extra latency for the guest in certain
configurations.
So, until we can get actual benchmark data to see if that's the case,
this restores the old behaviour, issuing a MADV_WILLNEED when a page is
removed from the balloon.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a balloon bug with a nasty consequence - potentially
corrupting guest memory - but which is extremely unlikely to be
triggered in practice.
The balloon always works in 4kiB units, but the host could have a
larger page size on certain platforms. Since ed48c59 "virtio-balloon:
Safely handle BALLOON_PAGE_SIZE < host page size" we've handled this
by accumulating requests to balloon 4kiB subpages until they formed a
full host page. Since f6deb6d "virtio-balloon: Remove unnecessary
MADV_WILLNEED on deflate" we essentially ignore deflate requests.
Suppose we have a host with 8kiB pages, and one host page has subpages
A & B. If we get this sequence of events -
inflate A
deflate A
inflate B
- the current logic will discard the whole host page. That's
incorrect because the guest has deflated subpage A, and could have
written important data to it.
This patch fixes the problem by adjusting our state information about
partially ballooned host pages when deflate requests are received.
Fixes: ed48c59 "virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-3-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
ed48c59875 "virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host
page size" introduced a new temporary data structure which tracks 4kiB
chunks which have been inserted into the balloon by the guest but
don't yet form a full host page which we can discard.
Unfortunately, I had a thinko and allocated that structure with
g_malloc0() but freed it with a plain free() rather than g_free().
This corrects the problem.
Fixes: ed48c59875
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190306030601.21986-2-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
The elem could theorically contain both outbuf and inbufs. We move the
free operation to the end of this function to avoid using elem->in_sg
while elem has been freed.
Fixes: c13c4153f7
("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Peter Xu <peterx@redhat.com>
Message-Id: <1552383280-4122-1-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The implementation used blocks units rather than the expected bytes.
Fixes: c03e7ef12a ("nvme: Implement Write Zeroes")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some machines have an SDHCI device, but no PCI. To be able to
compile hw/sd/sdhci.c without CONFIG_PCI, we must not call functions
like pci_get_address_space() and pci_allocate_irq() there. Thus
move the PCI-related code into a separate file.
This is required for the new Kconfig-like build system, e.g. it is
needed if a user wants to compile a QEMU binary with just one machine
that has SDHCI, but no PCI, like the ARM "raspi" machines for example.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This makes vfio_get_region_info_cap() to be used in quirks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190307050518.64968-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Activate only stop0 and stop1 levels. We should not need more levels
when under QEMU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To improve OPAL/skiboot support. We don't need to strictly model these
XSCOM accesses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new class attribute to define XSCOM operations per CPU
family and add a couple of XSCOM addresses controlling the power
management states of the core on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV LPC Controller exposes different sets of registers for
each of the functional units it encompasses, among which the OPB
(On-Chip Peripheral Bus) Master and Arbitrer and the LPC HOST
Controller.
The mapping addresses of each register range are correct but the sizes
are too large. Fix the sizes and define the OPB Arbitrer range to fill
the gap between the OPB Master registers and the LPC HOST Controller
registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PSI bridge on POWER9 is very similar to POWER8. The BAR is still
set through XSCOM but the controls are now entirely done with MMIOs.
More interrupts are defined and the interrupt controller interface has
changed to XIVE. The POWER9 model is a first example of the usage of
the notify() handler of the XiveNotifier interface, linking the PSI
XiveSource to its owning device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the PSI bridge model for POWER9, abstract
the POWER chip differences in a PnvPsi class model and introduce a
specific Pnv8Psi type for POWER8. POWER8 interface to the interrupt
controller is still XICS whereas POWER9 uses the new XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the New World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the Old World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On sPAPR vfio_listener_region_add() is called in 2 situations:
1. a new listener is registered from vfio_connect_container();
2. a new IOMMU Memory Region is added from rtas_ibm_create_pe_dma_window().
In both cases vfio_listener_region_add() calls
memory_region_iommu_replay() to notify newly registered IOMMU notifiers
about existing mappings which is totally desirable for case 1.
However for case 2 it is nothing but noop as the window has just been
created and has no valid mappings so replaying those does not do anything.
It is barely noticeable with usual guests but if the window happens to be
really big, such no-op replay might take minutes and trigger RCU stall
warnings in the guest.
For example, a upcoming GPU RAM memory region mapped at 64TiB (right
after SPAPR_PCI_LIMIT) causes a 64bit DMA window to be at least 128TiB
which is (128<<40)/0x10000=2.147.483.648 TCEs to replay.
This mitigates the problem by adding an "skipping_replay" flag to
sPAPRTCETable and defining sPAPR own IOMMU MR replay() hook which does
exactly the same thing as the generic one except it returns early if
@skipping_replay==true.
Another way of fixing this would be delaying replay till the very first
H_PUT_TCE but this does not work if in-kernel H_PUT_TCE handler is
enabled (a likely case).
When "ibm,create-pe-dma-window" is complete, the guest will map only
required regions of the huge DMA window.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190307050518.64968-2-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reset all regs but keep the MMIO BAR enabled as it is at realize time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple helper to translate XSCOM addresses to MMIO addresses
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The NSR register of the HV ring has a different, although similar, bit
layout. TM_QW3_NSR_HE_PHYS bit should now be raised when the
Hypervisor interrupt line is signaled. Other bits TM_QW3_NSR_HE_POOL
and TM_QW3_NSR_HE_LSI are not modeled. LSI are for special interrupts
reserved for HW bringup and the POOL bit is used when signaling a
group of VPs. This is not currently implemented in Linux but it is in
pHyp.
The most important special commands on the HV TIMA page are added to
let the core manage interrupts : acking and changing the CPU priority.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have different interrupt controllers,
and reporting their state requires calling different helper routines.
However, the interrupt presenters are still handled in the higher
level pic_print_info() routine because they are not related to the
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have a different set of devices and a
different device tree layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine with need to encode the block id in the source
interrupt number before forwarding the source event notification to
the Router.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can perform indirect loads and stores on the TIMA
on behalf of another CPU. Give the controller the possibility to call
the TIMA memory accessors with a XiveTCTX of its choice.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
By default on P9, the HW CAM line (23bits) is hardwired to :
0x000||0b1||4Bit chip number||7Bit Thread number.
When the block group mode is enabled at the controller level (PowerNV),
the CAM line is changed for CAM compares to :
4Bit chip number||0x001||7Bit Thread number
This will require changes in xive_presenter_tctx_match() possibly.
This is a lowlevel functionality of the HW controller and it is not
strictly needed. Leave it for later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Original commit message:
This patch adds an emulation model for i2c controller found on most of the FSL SoCs.
It also integrates the RTC (ds1338) that sits on the i2c Bus with e500 machine model.
Patch was originally written by Amit Singh Tomar <amit.tomar@freescale.com>
see http://patchwork.ozlabs.org/patch/431475/
I only fixed it enough for application on top of current qemu master
20b084c4b1, and hopefully fixed checkpatch errors
Tested by booting Linux kernel 4.20.12. Now e500 machine doesn't need
network time protocol daemon because it will have working RTC
(before all timestamps on files were from 2016)
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Signed-off-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190306102812.28972-1-randrianasulu@gmail.com>
[dwg: Add Kconfig stanza to define the new symbol, update MAINTAINERS]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_CALL H_PAGE_INIT can be used to zero or copy a page of guest
memory. Enable the in-kernel H_PAGE_INIT handler.
The in-kernel handler takes half the time to complete compared to
handling the H_CALL in userspace.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190306060608.19935-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we allocate a hash page table then we know that the guest won't be
using process tables, so set the partition table entry maintained for
the guest to zero. If this isn't done, then the guest radix bit will
remain set in the entry. This means that when the guest calls
H_REGISTER_PROCESS_TABLE there will be a mismatch between then flags
and the value in spapr->patb_entry, and the call will fail. The guest
will then panic:
Failed to register process table (rc=-4)
kernel BUG at arch/powerpc/platforms/pseries/lpar.c:959
The result being that it isn't possible to boot a hash guest on a P9
system.
Also fix a bug in the flags parsing in h_register_process_table() which
was introduced by the same patch, and simplify the handling to make it
less likely that errors will be introduced in the future. The effect
would have been setting the host radix bit LPCR_HR for a hash guest
using process tables, which currently isn't supported and so couldn't
have been triggered.
Fixes: 00fd075e18 "target/ppc/spapr: Set LPCR:HR when using Radix mode"
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190305022102.17610-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are currently 3 mitigations the availability of which is controlled
by the spapr-caps mechanism, cap-cfpc, cap-sbbc, and cap-ibs. Enable these
mitigations by default for the pseries-4.0 machine type.
By now machine firmware should have been upgraded to allow these
settings.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-3-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_caps cap-cfpc, cap-sbbc and cap-ibs are used to control the
availability of certain mitigations to the guest. These haven't been
implemented under TCG, it is unlikely they ever will be, and it is unclear
as to whether they even need to be.
As such, make failure to apply these capabilities under TCG non-fatal.
Instead we print a warning message to the user but still allow the guest
to continue.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-2-sjitindarsingh@gmail.com>
[dwg: Small style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new spapr_cap SPAPR_CAP_CCF_ASSIST to be used to indicate
the requirement for a hw-assisted version of the count cache flush
workaround.
The count cache flush workaround is a software workaround which can be
used to flush the count cache on context switch. Some revisions of
hardware may have a hardware accelerated flush, in which case the
software flush can be shortened. This cap is used to set the
availability of such hardware acceleration for the count cache flush
routine.
The availability of such hardware acceleration is indicated by the
H_CPU_CHAR_BCCTR_FLUSH_ASSIST flag being set in the characteristics
returned from the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_cap SPAPR_CAP_IBS is used to indicate the level of capability
for mitigations for indirect branch speculation. Currently the available
values are broken (default), fixed-ibs (fixed by serialising indirect
branches) and fixed-ccd (fixed by diabling the count cache).
Introduce a new value for this capability denoted workaround, meaning that
software can work around the issue by flushing the count cache on
context switch. This option is available if the hypervisor sets the
H_CPU_BEHAV_FLUSH_COUNT_CACHE flag in the cpu behaviours returned from
the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Enable the large decrementer by default for the pseries-4.0 machine type.
It is disabled again by default_caps_with_cpu() for pre-POWER9 cpus
since they don't support the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-4-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement support to allow KVM guests to take advantage of the large
decrementer introduced on POWER9 cpus.
To determine if the host can support the requested large decrementer
size, we check it matches that specified in the ibm,dec-bits device-tree
property. We also need to enable it in KVM by setting the LPCR_LD bit in
the LPCR. Note that to do this we need to try and set the bit, then read
it back to check the host allowed us to set it, if so we can use it but
if we were unable to set it the host cannot support it and we must not
use the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-3-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior to POWER9 the decrementer was a 32-bit register which decremented
with each tick of the timebase. From POWER9 onwards the decrementer can
be set to operate in a mode called large decrementer where it acts as a
n-bit decrementing register which is visible as a 64-bit register, that
is the value of the decrementer is sign extended to 64 bits (where n is
implementation dependant).
The mode in which the decrementer operates is controlled by the LPCR_LD
bit in the logical paritition control register (LPCR).
>From POWER9 onwards the HDEC (hypervisor decrementer) was enlarged to
h-bits, also sign extended to 64 bits (where h is implementation
dependant). Note this isn't configurable and is always enabled.
On POWER9 the large decrementer and hdec are both 56 bits, as
represented by the lrg_decr_bits cpu class property. Since they are the
same size we only add one property for now, which could be extended in
the case they ever differ in the future.
We also add the lrg_decr_bits property for POWER5+/7/8 since it is used
to determine the size of the hdec, which is only generated on the
POWER5+ processor and later. On these processors it is 32 bits.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add spapr_cap SPAPR_CAP_LARGE_DECREMENTER to be used to control the
availability of the large decrementer for a guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-1-sjitindarsingh@gmail.com>
[dwg: Trivial style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit b8165118f5 broke CPU hotplug tests for old machine types:
$ QTEST_QEMU_BINARY=ppc64-softmmu/qemu-system-ppc64 ./tests/cpu-plug-test -m=slow
/ppc64/cpu-plug/pseries-3.1/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12-sxxm/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-3.0/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.10/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.11/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.9/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.7/device-add/2x3x1&maxcpus=6: **
ERROR:/home/thuth/devel/qemu/hw/ppc/spapr_events.c:313:rtas_event_log_to_source: assertion failed: (source->enabled)
Broken pipe
/home/thuth/devel/qemu/tests/libqtest.c:143: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
Aborted (core dumped)
The approach of faking the availability of OV5_HP_EVT causes the
code to assume the hotplug event source is enabled, which is wrong
for older machines.
We've now fixed CAS under qtest with a different approach. Therefore,
this reverts commit b8165118f5.
A subsequent patch will address the problem of CAS under qtest from
a different angle.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875097.147873.1732264036668112686.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The RTAS event hotplug code for machine types 2.8 and newer depends on
the CAS negotiated ov5 in order to work properly. However, there's no
CAS when running under qtest. There has been a tentative to trick the
code by faking the OV5_HP_EVT bit, but it turned out to break other
assumptions in the code and the change got reverted.
Go for a more general approach and simulate a CAS when running under
qtest. For simplicity, this pseudo CAS simple simulates the case where
the guest supports the same features as the machine. It is done at
reset time, just before we reset the DRCs, which could potentially
exercise the unplug code.
This allows to test unplug on spapr with both older and newer machine
types.
Suggested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875704.147873.10563808578795890265.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "systempagesize" name suggests that it is the host system page size
while it is the smallest page size of memory backing the guest RAM so
let's rename it to stop confusion. This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-4-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current code assumes that we can address more bits on a PCI bus
for DMA than we really can but there is no way knowing the actual limit.
This makes a better guess for the number of levels and if the kernel
fails to allocate that, this increases the level numbers till succeeded
or reached the 64bit limit.
This adds levels to the trace point.
This may cause the kernel to warn about failed allocation:
[65122.837458] Failed to allocate a TCE memory, level shift=28
which might happen if MAX_ORDER is not large enough as it can vary:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/Kconfig?h=v5.0-rc2#n727
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190227085149.38596-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PC machines put firmware in ROM by default. To get it put into
flash memory (required by OVMF), you have to use -drive
if=pflash,unit=0,... and optionally -drive if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, it creates two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
Mapping -drive if=none,... to -blockdev is a solved problem. With
if=T other than if=none, -drive additionally configures a block device
frontend. For non-onboard devices, that part maps to -device. Also a
solved problem. For onboard devices such as PC flash memory, we have
an unsolved problem.
This is actually an instance of a wider problem: our general device
configuration interface doesn't cover onboard devices. Instead, we have
a zoo of ad hoc interfaces that are much more limited. One of them is
-drive, which we'd rather deprecate, but can't until we have suitable
replacements for all its uses.
Sadly, I can't attack the wider problem today. So back to the narrow
problem.
My first idea was to reduce it to its solved buddy by using pluggable
instead of onboard devices for the flash memory. Workable, but it
requires some extra smarts in firmware descriptors and libvirt. Paolo
had an idea that is simpler for libvirt: keep the devices onboard, and
add machine properties for their block backends.
The implementation is less than straightforward, I'm afraid.
First, block backend properties are *qdev* properties. Machines can't
have those, as they're not devices. I could duplicate these qdev
properties as QOM properties, but I hate that.
More seriously, the properties do not belong to the machine, they
belong to the onboard flash devices. Adding them to the machine would
then require bad magic to somehow transfer them to the flash devices.
Fortunately, QOM provides the means to handle exactly this case: add
alias properties to the machine that forward to the onboard devices'
properties.
Properties need to be created in .instance_init() methods. For PC
machines, that's pc_machine_initfn(). To make alias properties work,
we need to create the onboard flash devices there, too. Requires
several bug fixes, in the previous commits. We also have to realize
the devices. More on that below.
If the user sets pflash0, firmware resides in flash memory.
pc_system_firmware_init() maps and realizes the flash devices.
Else, firmware resides in ROM. The onboard flash devices aren't used
then. pc_system_firmware_init() destroys them unrealized, along with
the alias properties.
The existing code to pick up drives defined with -drive if=pflash is
replaced by code to desugar into the machine properties.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <87ftrtux81.fsf@dusky.pond.sub.org>
pc_system_firmware_init() parameter @isapc_ram_fw is PCMachineState
member pci_enabled negated. The next commit will need more of
PCMachineState. To prepare for that, pass a PCMachineState *, and
drop the now redundant parameter @isapc_ram_fw.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-11-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This structure is not used since commit 6dd2a5c98a.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308131445.17502-10-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Add an helper to access the opaque struct PFlashCFI01.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-9-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
The first call of sysbus_get_default() creates the main system bus and
stores it in QOM as "/machine/unattached/sysbus". This must not
happen before main() creates "/machine", or else container_get() would
"helpfully" create it as "container" object, and the real creation of
"/machine" would later abort with "attempt to add duplicate property
'machine' to object (type 'container')". Has been that way ever since
we wired up busses in QOM (commit f968fc6892, v1.2.0).
I believe the bug is latent. I got it to bite by trying to
qdev_create() a sysbus device from a machine's .instance_init()
method.
The fix is obvious: store the main system bus in QOM right after
creating "/machine".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190308131445.17502-5-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
See the previous commit for rationale.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308131445.17502-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Compatibility properties started life as a qdev property thing: we
supported them only for qdev properties, and implemented them with the
machinery backing command line option -global.
Recent commit fa0cb34d22 put them to use (tacitly) with memory
backend objects (subtypes of TYPE_MEMORY_BACKEND). To make that
possible, we first moved the work of applying them from the -global
machinery into TYPE_DEVICE's .instance_post_init() method
device_post_init(), in commits ea9ce8934c and b66bbee39f, then made
it available to TYPE_MEMORY_BACKEND's .instance_post_init() method
host_memory_backend_post_init() as object_apply_compat_props(), in
commit 1c3994f6d2.
Note the code smell: we now have function name starting with object_
in hw/core/qdev.c. It has to be there rather than in qom/, because it
calls qdev_get_machine() to find the current accelerator's and
machine's compat_props.
Turns out calling qdev_get_machine() there is problematic. If we
qdev_create() from a machine's .instance_init() method, we call
device_post_init() and thus qdev_get_machine() before main() can
create "/machine" in QOM. qdev_get_machine() tries to get it with
container_get(), which "helpfully" creates it as "container" object,
and returns that. object_apply_compat_props() tries to paper over the
problem by doing nothing when the value of qdev_get_machine() isn't a
TYPE_MACHINE. But the damage is done already: when main() later
attempts to create the real "/machine", it fails with "attempt to add
duplicate property 'machine' to object (type 'container')", and
aborts.
Since no machine .instance_init() calls qdev_create() so far, the bug
is latent. But since I want to do that, I get to fix the bug first.
Observe that object_apply_compat_props() doesn't actually need the
MachineState, only its the compat_props member of its MachineClass and
AccelClass. This permits a simple fix: register MachineClass and
AccelClass compat_props with the object_apply_compat_props() machinery
right after these classes get selected.
This is actually similar to how things worked before commits
ea9ce8934c and b66bbee39f, except we now register much earlier. The
old code registered them only after the machine's .instance_init()
ran, which would've broken compatibility properties for any devices
created there.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190308131445.17502-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
pflash_cfi01_register() takes a size in bytes, a block size in bytes
and a number of blocks. mips_malta_init() passes BIOS_SIZE, 65536,
FLASH_SIZE >> 16. Actually consistent only because BIOS_SIZE (defined
in include/hw/mips/bios.h as (4 * MiB)) matches FLASH_SIZE (defined
locally as 0x400000). Confusing all the same.
Pass FLASH_SIZE instead of BIOS_SIZE.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Aleksandar Rikalo <arikalo@wavecomp.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190308094610.21210-14-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The 'bios_size' variable is only used in the 'if (!kernel_filename &&
!dinfo)' clause. This is the case when we don't provide -pflash command
line option, and also don't provide a -kernel option. In this case we
will check for the -bios option, or use the default BIOS_FILENAME file.
The 'bios' term is valid in this if statement, but is confuse in the
whole mips_malta_init() scope. Restrict his scope.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-13-armbru@redhat.com>
Variable fl_sectors is used just once. Since
fl_sectors = bios_size >> 16 and bios_size = FLASH_SIZE there,
we can simply use FLASH_SIZE >> 16, and eliminate variable.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-12-armbru@redhat.com>
The debug code under DEBUG_BOARD_INIT doesn't compile:
hw/mips/mips_malta.c:1273:16: error: implicit declaration of function ‘blk_name’; did you mean ‘basename’? [-Werror=implicit-function-declaration]
blk_name(dinfo->bdrv), fl_sectors);
^~~~~~~~
hw/mips/mips_malta.c:1273:16: error: nested extern declaration of ‘blk_name’ [-Werror=nested-externs]
hw/mips/mips_malta.c:1273:30: error: ‘DriveInfo’ {aka ‘struct DriveInfo’} has no member named ‘bdrv’
blk_name(dinfo->bdrv), fl_sectors);
^~
Delete it.
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190308094610.21210-11-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
pflash_cfi02_register() takes a size in bytes, a block size in bytes
and a number of blocks. r2d_init() passes FLASH_SIZE, 16 * KiB,
FLASH_SIZE >> 16. Does not compute: size doesn't match block size *
number of blocks. The latter happens to win: FLASH_SIZE / 4,
i.e. 8MiB.
The best information we have on the physical hardware lists a Cypress
S29PL127J60TFI130 128MiBit NOR flash addressable in words of 16 bits,
in sectors of 4 and 32 Kibiwords. We don't model multiple sector
sizes.
Fix the flash size from 8 to 16MiB, and adjust the sector size from 16
to 64KiB. Fix the width from 4 to 2. While there, supply the real
device IDs 0x0001, 0x227e, 0x2220, 0x2200 instead of zeros.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-10-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Machine "ref405ep" maps its flash memory at address 2^32 - image size.
Image size is rounded up to the next multiple of 64KiB. Useless,
because pflash_cfi02_realize() fails with "failed to read the initial
flash content" unless the rounding is a no-op.
If the image size exceeds 0x80000 Bytes, we overlap first SRAM, then
other stuff. No idea how that would play out, but useful outcomes
seem unlikely.
Map the flash memory at fixed address 0xFFF80000 with size 512KiB,
regardless of image size, to match the physical hardware.
Machine "taihu" maps its boot flash memory similarly. The code even
has a comment /* XXX: should check that size is 2MB */, followed by
disabled code to adjust the size to 2MiB regardless of image size.
Its code to map its application flash memory looks the same, except
there the XXX comment asks for 32MiB, and the code to adjust the size
isn't disabled. Note that pflash_cfi02_realize() fails with "failed
to read the initial flash content" for images smaller than 32MiB.
Map the boot flash memory at fixed address 0xFFE00000 with size 2MiB,
to match the physical hardware. Delete dead code from application
flash mapping, and simplify some.
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-9-armbru@redhat.com>
The disabled DEBUG_BOARD_INIT code goes back to the initial commit
1a6c088620, and has since seen only mechanical updates. It sure
feels like useless clutter now. Delete it.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308094610.21210-8-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Machine "sam460ex" maps its flash memory at address 0xFFF00000. When
no image is supplied, its size is 1MiB (0x100000), and 512KiB of ROM
get mapped on top of its second half. Else, it's the size of the
image rounded up to the next multiple of 64KiB.
The rounding is actually useless: pflash_cfi01_realize() fails with
"failed to read the initial flash content" unless it's a no-op.
I have no idea what happens when the pflash's size exceeds 1MiB.
Useful outcomes seem unlikely.
I guess memory at the end of the address space remains unmapped when
it's smaller than 1MiB. Again, useful outcomes seem unlikely.
The physical hardware appears to have 512KiB of flash memory:
https://eu.mouser.com/datasheet/2/268/atmel_AT49BV040B-1180330.pdf
For now, just set the flash memory size to 1MiB regardless of image
size, and document the mess.
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
pflash_cfi01.c and pflash_cfi02.c start their identifiers with
pflash_cfi01_ and pflash_cfi02_ respectively, except for
CFI_PFLASH01(), TYPE_CFI_PFLASH01, CFI_PFLASH02(), TYPE_CFI_PFLASH02.
Rename for consistency.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-5-armbru@redhat.com>
Our implementation of "write to buffer" (command 0xE8) is flawed.
LOG_UNIMP its use, and add some FIXME comments.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-4-armbru@redhat.com>
When a guest tries to abort "write to buffer" (command 0xE8), we print
"PFLASH: Possible BUG - Write block confirm", then exit(1). Letting
the guest terminate QEMU is not a good idea. Instead, LOG_UNIMP we
screwed up, then reset the device.
Macro PFLASH_BUG() is now unused; delete it.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-3-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Kick the display link up event with a 0.1 sec delay,
so the guest has a chance to notice the link down first.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[update for redefined macro]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This allows configure the display resolution which the vgpu should use.
The information will be passed to the guest using EDID, so the mdev
driver must support the vfio edid region for this to work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds EDID support to the vfio display (aka vgpu) code.
When supported by the mdev driver qemu will generate a EDID blob
and pass it on using the new vfio edid region. The EDID blob will
be updated on UI changes (i.e. window resize), so the guest can
adapt.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[remove control flow via macro, use unsigned format specifier]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since commit 578f3c7b08 ("arm: add fw_cfg to "virt" board",
2014-12-22), the machvirt_init() unconditionally creates the
fw_cfg object. Later, commit c30e15658b ("smbios: implement
smbios support for mach-virt", 2015-09-07) added a superfluous
null-check on it.
Remove this superfluous check.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190309181920.30553-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 'boot_splash_filedata_size' was introduced as a global variable
in 3d3b8303c6. This variable is used as a 'size' argument to the
fw_cfg_add_file(). This function has an interface contract with its
'data' argument, but there is no such contract for 'size' (this is
not a referenced pointer). We can simply remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308013222.12524-7-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190218175529.11237-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Code was assigning DFIFO, but didn't return the value to users.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190305195519.24303-6-svens@stackframe.org>
This makes trace logs much easier to read, especially for
people who are not fluent in SCSI.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-5-svens@stackframe.org>
This makes the code easier to read - no functional change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-4-svens@stackframe.org>
This makes the code easier to read - no functional change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-3-svens@stackframe.org>
Instead of using the open-coded versions, use the helper already
present as this makes the code easier to read and less error-prone.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-2-svens@stackframe.org>
Qemu will crash with the assertion error that "assert(r->req.aiocb !=
NULL)" in scsi_read_complete if request is invaild or disk is no medium.
The error is below:
qemu-kvm: hw/scsi/scsi_disk.c:299: scsi_read_complete: Assertion
`r->req.aiocb != NULL' failed.
This patch add a funtion scsi_read_complete_noio to fix it.
Signed-off-by: Zhengui Li <lizhengui@huawei.com>
Message-Id: <1551949966-20092-1-git-send-email-lizhengui@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Kiarie <davidkiarie4@gmail.com>
Message-Id: <20190304151827.1813-2-davidkiarie4@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If SIGP is set, the 'Wait for Reselection' command should jump
immediately to the address stored in the second DWORD of the
instruction. This fixes spurious hangs in the HP-UX 11.11
installer when the SIGP bit gets set by the kernel before the
'Wait for Reselection' command is executed by SCRIPTS.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Helge Deller <deller@gmx.de>
Message-Id: <20190217113717.7077-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HP-UX checks this register after sending data to the target. If there's no valid
information present, it assumes the client disconnected because the kernel sent
to much data. Implement at least some of the SBCL functionality that is possible
without having a real SCSI bus.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190215194021.20543-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Build fails with gcc 9:
CC ppc64-softmmu/hw/scsi/virtio-scsi.o
hw/scsi/virtio-scsi.c: In function ‘virtio_scsi_do_tmf’:
hw/scsi/virtio-scsi.c:265:39: error: taking address of packed member of ‘struct virtio_scsi_ctrl_tmf_req’ may result in an unaligned pointer value [-Werror=address-of-packed-member]
265 | virtio_tswap32s(VIRTIO_DEVICE(s), &req->req.tmf.subtype);
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
All the fields in struct virtio_scsi_ctrl_tmf_req are naturally aligned,
so we could in theory drop QEMU_PACKED. Unfortunately, the header file
is imported from linux which already has the packed attribute. Trying to
fix that in the update-linux-headers.sh script is likely to produce
ugliness. Turn the call to virtio_tswap32s() into an assignment instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155137678223.44753.5438092367451176318.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Processor Trace required CPUID[0x14] but the cpuid_level
have no change when create a kvm guest with
e.g. "-cpu qemu64,+intel-pt".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Message-Id: <1548805979-12321-1-git-send-email-luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some multiboot images could be in the ELF format. In the current
implementation QEMU fails because we try to load these images
as a PVH image.
In order to fix this issue, we should try multiboot first (we
already check the multiboot magic header before to load it).
If it is not a multiboot image, we can try the PVH loader.
Fixes: ab969087da ("pvh: Boot uncompressed kernel using direct boot ABI", 2019-01-15)
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190214180216.246707-1-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-enable PCI_DEVICES for RISC-V.
The patch is based on other <arch>/Kconfig.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: 82a230d5a3 ("riscv-softmmu.mak: replace CONFIG_* with Kconfig "select" directives")
Message-Id: <20190311091256.18385-1-david.abdurachmanov@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_VFIO_PCI was not "default y" - and once you do that, it is also
important to disable it if PCI is not there.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As NVDIMM support is looming for ARM and SPAPR, let's
move the acpi_nvdimm_state to the generic machine struct
instead of duplicating the same code in several machines.
It is also renamed into nvdimms_state and becomes a pointer.
nvdimm and nvdimm-persistence become generic machine options.
They become guarded by a nvdimm_supported machine class member.
We also add a description for those options.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190308182053.5487-3-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As we intend to migrate the acpi_nvdimm_state into
the base machine with a new dimms_state name, let's
also rename the datatype.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308182053.5487-2-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add (partial) emulation of the on-board GPU of the machine. This
allows the PMON2000 firmware to run and should also work with Linux
console but probably not with X yet.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-id: da6370b22e0352ee803d25d68a62ff32eebf06e2.1552152100.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
At least two machines, the PPC mac99 and MIPS fulong2e, have an ATI
gfx chip by default (Rage 128 Pro and M6/RV100 respectively) and
guests running on these and the PMON2000 firmware of the fulong2e
expect this to be available. Fortunately these are very similar chips
so they can be mostly emulated in the same device model. This patch
adds basic emulation of these ATI VGA chips.
While this is incomplete and currently only enough to run the MIPS
firmware and get framebuffer output with Linux, it allows the fulong2e
board to work more like the real hardware and having it in QEMU in
this state provides a way to experiment with it and allows others to
contribute to improve it. It is compiled for all archs but only the
fulong2e (which currently has no display output at all) is set to use
it by default (in a separate patch).
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Tested-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Tested-by: Howard Spoelstra <hsp.cat7@gmail.com>
Message-id: 0b1b7c22873a6e37627261b04fb687412b25ff4f.1552152100.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-4-kraxel@redhat.com
Store reset handler of the parent class and just call that for a
complete virtio reset. When taking the shortcut and calling
virtio_gpu_reset() directly the generic virtio reset code (for
virtqueues etc) will not be executed.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1597621
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-3-kraxel@redhat.com
Needed when VirtioPCIClass subclasses have their own
class struct with some extra fields.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-2-kraxel@redhat.com
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that USB_OHCI was missing (it was brought in via pci.mak,
but r2d needs the sysbus version) and SERIAL is not used.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of hard-coding all config switches in the config file
default-configs/s390x-softmmu.mak, let's use the new Kconfig files
to express the necessary dependencies: The S390_CCW_VIRTIO config switch
for the "s390-ccw-virtio" machine now selects all non-optional devices.
And since we already have the VIRTIO_PCI and VIRTIO_MMIO config switches
for the other two virtio transports, this patch also introduces a new
config switch VIRTIO_CCW for the third, s390x-specific virtio transport,
so that all three virtio transports are now handled in the same way.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Moxie does not use VGA, ISA or RTC, and only has a memory-mapped
serial port. Adjust for the correct dependencies.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that the Dino board uses a memory mapped 16550 UART and
therefore only CONFIG_SERIAL is needed, not CONFIG_SERIAL_ISA.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes it much easier if the users want to disable some of
the embedded machines for their builds.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most of the dependencies are now directly selected by the SAM460EX
switch. We can drop CONFIG_VGA_CIRRUS since this device is already
selected automatically when CONFIG_PCI_DEVICES is set.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it for example easier if the users want to disable
one of the two machines for their builds.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Select the required devices in hw/ppc/Kconfig instead, so that
ppc-softmmu.mak only contains the user-selectable PREP switch.
Plug-in devices like NE2000_ISA are pulled in automatically by the
Kconfig build system now.
Cc: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The POWERNV switch should always select ISA_IPMI_BT, then the other
IPMI options are turned on automatically now.
CONFIG_DIMM should always be selected by the pseries machine,
which in turn depends on CONFIG_MEM_DEVICE since DIMM implements
this interface.
CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak
completely since this device is already automatically enabled via
hw/display/Kconfig now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This automatically removes the TPM backends from the
binary altogether if no front-ends are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
remove default-configs/hyperv.mak and make dependencies
with Kconfig.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-41-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This automatically removes the SCSI subsystem from the
binary altogether if no controllers are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-34-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
let the host controllers select CONFIG_USB and make the devices
default to present whenever USB is available.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on USB' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/usb.mak
followed by adding "select USB" on the host controllers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-33-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is really nothing special in these devices; they are just
ISA devices. Instead of including them for each target,
set CONFIG_ISA_BUS to true, and make the devices default to present
whenever ISA is available. More conversion of ISA devices will
follow.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on ISA_BUS' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/sound.mak
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-32-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make pcie splited from pci and make it configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-30-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-29-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Devices that are mostly used for testing purposes (for example in
endianness-test) will be moved under a new symbol CONFIG_TEST_DEVICES
that can be disabled in the default-configs file. This makes
it easier to drop this code from QEMU if desirable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use CONFIG_EDID to make edid-generate.c and edid-region.c
configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-26-yang.zhong@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VIRTIO_9P || VIRTFS && XEN condition can be computed in hw/Makefile.objs,
removing an "if" from hw/9pfs/Makefile.objs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some functions sometimes uses req->dev even though a local variable
VirtIOBlock* s = req->dev has already been defined.
Updated places to use s everywhere in the file.
Signed-off-by: Anastasiia Rusakova <arusakova917@gmail.com>
Message-id: 20190307161925.4158-1-rusakova.nastasia@icloud.com
Message-Id: <20190307161925.4158-1-rusakova.nastasia@icloud.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With certain USB devices passed through via usb-host, a guest attempting to
reset a usb-host device can trigger a reset loop that renders the USB device
unusable. In my use case, the device was an iPhone XR that was passed through to
a Mac OS X Mojave guest. Upon connecting the device, the following happens:
1) Guest recognizes new device, sends reset to emulated USB host
2) QEMU's USB host sends reset to host kernel
3) Host kernel resets device
4) After reset, host kernel determines that some part of the device descriptor
has changed ("device firmware changed" in dmesg), so host kernel decides to
re-enumerate the device.
5) Re-enumeration causes QEMU to disconnect and reconnect the device in the
guest.
6) goto 1)
Here's from the host kernel (note the "device firmware changed" lines")
[3677704.473050] usb 1-1.3: new high-speed USB device number 53 using ehci-pci
[3677704.555594] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677704.555599] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677704.555602] usb 1-1.3: Product: iPhone
[3677704.555605] usb 1-1.3: Manufacturer: Apple Inc.
[3677704.555607] usb 1-1.3: SerialNumber: [[removed]]
[3677709.401040] usb 1-1.3: reset high-speed USB device number 53 using ehci-pci
[3677709.479486] usb 1-1.3: device firmware changed
[3677709.479842] usb 1-1.3: USB disconnect, device number 53
[3677709.546039] usb 1-1.3: new high-speed USB device number 54 using ehci-pci
[3677709.627471] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677709.627476] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677709.627479] usb 1-1.3: Product: iPhone
[3677709.627481] usb 1-1.3: Manufacturer: Apple Inc.
[3677709.627483] usb 1-1.3: SerialNumber: [[removed]]
[3677762.320044] usb 1-1.3: reset high-speed USB device number 54 using ehci-pci
[3677762.615630] usb 1-1.3: USB disconnect, device number 54
[3677762.787043] usb 1-1.3: new high-speed USB device number 55 using ehci-pci
[3677762.869016] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677762.869024] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677762.869028] usb 1-1.3: Product: iPhone
[3677762.869032] usb 1-1.3: Manufacturer: Apple Inc.
[3677762.869035] usb 1-1.3: SerialNumber: [[removed]]
[3677815.662036] usb 1-1.3: reset high-speed USB device number 55 using ehci-pci
Here's from QEMU:
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/022: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/024: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/026: No such file or directory
The result of this is that the device remains permanently unusable in the guest.
The same problem has been previously reported for an iPad:
https://stackoverflow.com/questions/52617634/how-do-i-get-qemu-usb-passthrough-to-work-for-ipad-iphone
This problem can be elegantly solved by interrupting step 2) above. Instead of
passing through the reset, QEMU simply ignores it. To allow this to be
configured on a per-device level, a new parameter "no_guest_reset" is
introduced for the usb-host device. I can confirm that the configuration
described above (iPhone XS + Mojave guest) works flawlessly with
no_guest_reset=True specified.
Working command line for my scenario:
device_add usb-host,vendorid=0x05ac,productid=0x12a8,no_guest_reset=True,id=iphone
Best regards
Alexander
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190128140027.9448-1-kraxel@redhat.com
[ kraxel: rename parameter to "guest-reset" ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
During a write, free up the "path" before getting more data.
Also, while we at it, remove the confusing usage of d->fd for
storing mkdir status
Spotted by Coverity: CID 1398642
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
MTP writes objects in small chunks and at the end gets the
real file size to update the object metadata. If this fails for
any reason, return an INCOMPLETE_TRANSFER to the initiator
Spotted by Coverity: CID 1398651
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Let's use a wrapper instead of looking it up manually. This function can
than be reused when we explicitly want to have the bus hotplug handler
(e.g. when the bus hotplug handler was overwritten by the machine
hotplug handler).
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-4-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will allow to return another hotplug handler than the default
one for a specific bus based device type. Which is needed to handle
non trivial plug/unplug sequences that need the access to resources
configured outside of bus where device is attached.
That will allow for returned hotplug handler to orchestrate wiring
in arbitrary order, by chaining other hotplug handlers when
it's needed.
PS:
It could be used for hybrid virtio-mem and virtio-pmem devices
where it will return machine as hotplug handler which will do
necessary wiring at machine level and then pass control down
the chain to bus specific hotplug handler.
Example of top level hotplug handler override and custom plug sequence:
some_machine_get_hotplug_handler(machine){
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
return HOTPLUG_HANDLER(machine);
}
return NULL;
}
some_machine_device_plug(hotplug_dev, dev) {
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
/* do machine specific initialization */
some_machine_init_special_device(dev)
/* pass control to bus specific handler */
hotplug_handler_plug(dev->parent_bus->hotplug_handler, dev)
}
}
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-3-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When unplugging a device, at one point the device will be destroyed
via object_unparent(). This will, one the one hand, unrealize the
removed device hierarchy, and on the other hand, destroy/free the
device hierarchy.
When chaining hotplug handlers, we want to overwrite a bus hotplug
handler by the machine hotplug handler, to be able to perform
some part of the plug/unplug and to forward the calls to the bus hotplug
handler.
For now, the bus hotplug handler would trigger an object_unparent(), not
allowing us to perform some unplug action on a device after we forwarded
the call to the bus hotplug handler. The device would be gone at that
point.
machine_unplug_handler(dev)
/* eventually do unplug stuff */
bus_unplug_handler(dev)
/* dev is gone, we can't do more unplug stuff */
So move the object_unparent() to the original caller of the unplug. For
now, keep the unrealize() at the original places of the
object_unparent(). For implicitly chained hotplug handlers (e.g. pc
code calling acpi hotplug handlers), the object_unparent() has to be
done by the outermost caller. So when calling hotplug_handler_unplug()
from inside an unplug handler, nothing is to be done.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> calls unrealize(dev)
/* we can do more unplug stuff but device already unrealized */
}
object_unparent(dev)
In the long run, every unplug action should be factored out of the
unrealize() function into the unplug handler (especially for PCI). Then
we can get rid of the additonal unrealize() calls and object_unparent()
will properly unrealize the device hierarchy after the device has been
unplugged.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> only unplugs, does not unrealize
/* we can do more unplug stuff */
}
object_unparent(dev) -> will unrealize
The original approach was suggested by Igor Mammedov for the PCI
part, but I extended it to all hotplug handlers. I consider this one
step into the right direction.
To summarize:
- object_unparent() on synchronous unplugs is done by common code
-- "Caller of hotplug_handler_unplug"
- object_unparent() on asynchronous unplugs ("unplug requests") has to
be done manually
-- "Caller of hotplug_handler_unplug"
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-2-david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The qbus_is_full(BusState *bus) function (qdev_monitor.c) compares the max_index
value of the BusState structure with the max_dev value of the BusClass structure
to determine whether the maximum number of children has been reached for the
bus. The problem is, the max_index field of the BusState structure does not
necessarily reflect the number of devices that have been plugged into
the bus.
Whenever a child device is plugged into the bus, the bus's max_index value is
assigned to the child device and then incremented. If the child is subsequently
unplugged, the value of the max_index does not change and no longer reflects the
number of children.
When the bus's max_index value reaches the maximum number of devices
allowed for the bus (i.e., the max_dev field in the BusClass structure),
attempts to plug another device will be rejected claiming that the bus is
full -- even if the bus is actually empty.
To resolve the problem, a new 'num_children' field is being added to the
BusState structure to keep track of the number of children plugged into the
bus. It will be incremented when a child is plugged, and decremented when a
child is unplugged.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <1545062250-7573-1-git-send-email-akrowiak@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcf7GJAAoJEAUWMx68W/3n+lMP/Rl/d7hpi0Ve2fm3VEwoFJea
IRiqo7Yk6heyTCIutFq15pD2ef49AXHpLeGBp9gFNb4bdFTQzHmwOPxeJWig8YXV
m+j5sGRaM9sV8XX24DsZM7yFhpVJmWky8ivMSv3LeEmjx251B9CNL13dc/qVUQHv
lYP6ewnOmtjvR+x+z9Q/+vafnpLWJSxup1G0pZWdQfLpl71E2sMf7FY/G5EroVnf
AXmJb1sjdFXF7n968myfcgYETHsnY0SUa89Bcnd+i40DXvSfa4njXSdE4FOhyIim
n8c4SyRA/Ah2EUl+UGxn8TQ78C4RA3dUS+uXJDmjL1e4ACvqq//nhsfIqTJ9AbgF
Jhx5ArwqrGf7D+/PM5ivDocNplT5JFcCB4OCmZO96Kn0/F6M3UHuL1+IvpQcFMm8
1Ar1REB7BZ6f+QLfY8KKuzVrVRzUBi0DbqFHj5TNIStizOkuUEMMRpcWImBMzslG
531YgTnsSeFfFr13ZJlXDscZSZ5i+fJMjNbH9QpTNy8qmLJoZzbKqpmP4pZmHVI2
w3g1pCHpFejuQtUTNMR3+9mVH5hO+MNrANsTH0yfAXYDNToJ6NkY1nnILHp4P7t1
tqHYN7AO2ZXTTTMSnfyv1+2wh3HZRFB/y7uF6uEowBfuZTRHBHnkaVQp5WbVVSJu
4ovMmHDkcX2bM7VWwTHS
=dk89
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20190306a' into staging
Migation pull 2019-03-06
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
# gpg: Signature made Wed 06 Mar 2019 11:39:53 GMT
# gpg: using RSA key 0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20190306a: (22 commits)
qapi/migration.json: Remove a variable that doesn't exist in example
Migration/colo.c: Make COLO node running after failover
Migration/colo.c: Fix double close bug when occur COLO failover
virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT
migration/ram.c: add the free page optimization enable flag
migration/ram.c: add a notifier chain for precopy
migration: API to clear bits of guest free pages from the dirty bitmap
migration: use bitmap_mutex in migration_bitmap_clear_dirty
bitmap: bitmap_count_one_with_offset
bitmap: fix bitmap_count_one
tests: Add basic migration precopy tcp test
migration: Create socket-address parameter
tests: Add migration xbzrle test
migration: Add capabilities validation
tests/migration-test: Add a test for ignore-shared capability
migration: Add an ability to ignore shared RAM blocks
migration: Introduce ignore-shared capability
exec: Change RAMBlockIterFunc definition
migration/rdma: clang compilation fix
migration: Cleanup during exit
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new feature enables the virtio-balloon device to receive hints of
guest free pages from the free page vq.
A notifier is registered to the migration precopy notifier chain. The
notifier calls free_page_start after the migration thread syncs the dirty
bitmap, so that the free page optimization starts to clear bits of free
pages from the bitmap. It calls the free_page_stop before the migration
thread syncs the bitmap, which is the end of the current round of ram
save. The free_page_stop is also called to stop the optimization in the
case when there is an error occurred in the process of ram saving.
Note: balloon will report pages which were free at the time of this call.
As the reporting happens asynchronously, dirty bit logging must be
enabled before this free_page_start call is made. Guest reporting must be
disabled before the migration dirty bitmap is synchronized.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Peter Xu <peterx@redhat.com>
Message-Id: <1544516693-5395-8-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Dropped kernel header update, fixed up CMD_ID_* name change
Don't dynamically allocate the pflash's timer. But do use timer_del in
an unrealize function to make sure that the timer can't fire after the
pflash_t has been freed.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190219153727.62279-1-stephen.checkoway@oberlin.edu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
acpi_table_builtin is now always false, it is not necessary to check it
again.
This patch just removes it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190214084939.20640-4-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Function acpi_table_add_builtin() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190214084939.20640-3-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Function pc_acpi_init() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190214084939.20640-2-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have the extended memory map (high IO regions beyond the
scalable RAM) and dynamic IPA range support at KVM/ARM level
we can bump the legacy 255GB initial RAM limit. The actual maximum
RAM size now depends on the physical CPU and host kernel, in
accelerated mode. In TCG mode, it depends on the VCPU
AA64MMFR0.PARANGE.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are about to allow the memory map to grow beyond 1TB and
potentially overshoot the VCPU AA64MMFR0.PARANGE.
In aarch64 mode and when highmem is set, let's check the VCPU
PA range is sufficient to address the highest GPA of the memory
map.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the machine class kvm_type() callback.
It returns the number of bits requested to implement the whole GPA
range including the RAM and IO regions located beyond.
The returned value is passed though the KVM_CREATE_VM ioctl and
this allows KVM to set the stage2 tables dynamically.
To compute the highest GPA used in the memory map, kvm_type()
must freeze the memory map by calling virt_set_memmap().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-9-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On ARM, the kvm_type will be resolved by querying the KVMState.
Let's add the MachineState handle to the callback so that we
can retrieve the KVMState handle. in kvm_init, when the callback
is called, the kvm_state variable is not yet set.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-5-eric.auger@redhat.com
[ppc parts]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We introduce an helper to create a memory node.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190304101339.25970-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Expose the virtio-net self announcement capability and allow
qemu_announce_self() to call it.
These announces are caused by something external (i.e. the
announce-self command); they won't trigger if the migration
counter is triggering announces at the same time.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Switch virtio's self announcement to use the AnnounceTimer.
It keeps it's own AnnounceTimer (per device), and starts running it
using a migration post-load and a virtual clock; that way the
announce happens once the guest is actually running.
The timer uses the migration parameters to set the timing of
the repeats.
Based on earlier patches by myself and
Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcdAQoAAoJEHWtZYAqC0IRuX4IAIIcHthcKTpBWl144gyXxh0i
o/yjf6eYdmy75blaRsEF7UjNiY5C6/EXbw8nX8mTAGtspAL5Tj1BXWgYVuQ02C6e
qdsN0Pcy6kVuqeCwE/6NjSWZCD7pdKA0EiB3H3tBgUEzmjXa6iHz8SlvpQwJQqAB
K0ItBPXnvggu5IZHxqNFOiZowBCNLmNSN7K3cZCUiHoeVa89t2FxykjeASQmmyUP
4vI/6qnLEOFLdvfPcfNBMtlXQII45w0xtB9QwTrn6in1alkPuzVxOcj7UZ0as5IV
/rsAjo3F6UF7oasYlnlwu3l3HYTaaGsJl23F2oUnHZkMtodFcOHKfIgPsXLnKgo=
=UgWQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2019-02-25-1' into staging
Merge tpm 2029/02/25 v1
# gpg: Signature made Mon 25 Feb 2019 15:05:12 GMT
# gpg: using RSA key 75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2019-02-25-1:
tpm_tis: convert tpm_tis_show_buffer() to use trace event
tpm_tis: fix loop that cancels any seizure by a lower locality
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccBqMAAoJECgfDbjSjVRpvSEIAKYPRNdCBX/SSS/L/tmJS5Zt
8IyU/HW1YJ249vO+aT6z4Q3QPgqNC3KjXC3brx/WRoPZnRroen4rv2Kqnk6SayPa
a52d2ubXKWxb3swdG1CAVzFRhq/ABpgAPx0dr1JW+RXgo2lxpJ4GNYxKMosQTaPE
hRNeXl1XlcIK525kJhFH3Hlij9mTRuY6T7ydpPQd8dUq2dBRaL9RrzZRrkZxCy6l
gQPUqNzPhG0XXyOiJmwYyVX0zGzbYrMLrMQAor2SBIYmU+zv2eZGPJUYxoMTUMzt
YR0WCpvkvPITlAryaBoozAIDYVz8PxBRT1KRwpDal+2rzlm6o+veKDiF8R46gn0=
=GzUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, tests
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 22 Feb 2019 15:51:40 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
pci: Sanity test minimum downstream LNKSTA
hw/smbios: fix offset of type 3 sku field
pci: Move NVIDIA vendor id to the rest of ids
virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size
virtio-balloon: Use ram_block_discard_range() instead of raw madvise()
virtio-balloon: Rework ballon_page() interface
virtio-balloon: Corrections to address verification
virtio-balloon: Remove unnecessary MADV_WILLNEED on deflate
i386/kvm: ignore masked irqs when update msi routes
contrib/vhost-user-blk: fix the compilation issue
Revert "contrib/vhost-user-blk: fix the compilation issue"
pc-dimm: use same mechanism for [get|set]_addr
tests/data: introduce "uefi-boot-images" with the "bios-tables-test" ISOs
tests/uefi-test-tools: add build scripts
tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app
roms: build the EfiRom utility from the roms/edk2 submodule
roms: add the edk2 project as a git submodule
vhost-user-test: create a temporary directory per TestServer
vhost-user-test: small changes to init_hugepagefs
vhost-user-test: create a main loop per TestServer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduces hot plug/unplug support for the vfio-ap device.
To hot plug a vfio-ap device using the QEMU device_add command:
(qemu) device_add vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
to which AP resources to be used by the guest have been assigned.
A vfio-ap device can be hot plugged only if:
1. A vfio-ap device has not been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
To hot unplug a vfio-ap device using the QEMU device_del command:
(qemu) device_del vfio-ap,sysfsdev=$path-to-mdev
Where $path-to-mdev is the absolute path to the mediated matrix device
specified when the vfio-ap device was attached to the virtual machine's
ap-bus.
A vfio-ap device can be hot unplugged only if:
1. A vfio-ap device has been attached to the virtual machine's ap-bus
via the QEMU command line or a prior hot plug action.
2. The guest was started with the CPU model feature for AP enabled
(e.g., -cpu host,ap=on)
Please note that a hot plug handler is not necessary for the vfio-ap device
because the AP matrix configuration for the guest is performed by the
kernel device driver when the vfio-ap device is realized. The vfio-ap device
represents a VFIO mediated device created in the host sysfs for use by a guest.
The mdev device is configured with an AP matrix (i.e., adapters and domains) via
its sysfs attribute interfaces prior to starting the guest or plugging a vfio-ap
device in. When the device is realized, a file descriptor is opened on the mdev
device which results in a callback to the vfio_ap kernel device driver. The
device driver then configures the AP matrix in the guest's SIE state description
from the AP matrix assigned via the mdev device's sysfs interfaces. The AP
devices will be created for the guest when the AP bus running on the guest
subsequently performs its periodic scan for AP devices.
The qdev_simple_device_unplug_cb() callback function is used for the same
reaons; namely, the vfio_ap kernel device driver will perform the AP resource
de-configuration for the guest when the vfio-ap device is unplugged. When the
vfio-ap device is unrealized, the mdev device file descriptor is closed which
results in a callback to the vfio_ap kernel device driver. The device driver
then clears the AP matrix configuration in the guest's SIE state description
and resets all of the affected queues. The AP devices created for the guest
will be removed when the AP bus running on the guest subsequently performs
its periodic scan and finds there are no longer any AP resources assigned to the
guest.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1550519397-25359-2-git-send-email-akrowiak@linux.ibm.com>
[CH: adapt to changed qbus_set_hotplug_handler() signature]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE/Q1c5nzg9ZpmiCaGYfOMkJGb/4EFAlx4Iv0ACgkQYfOMkJGb
/4HoUw/+IcrfemAuaEt0f7hOENpeWD4HYFCk0wgzXraSLaurREQHNP4KmYxz2xOS
ISLqgTty3dEjo95VXuSQUMm9ZaV1p8LquO+I1FnNGIt0otO3SMEh6/nOyrH1zY74
Q+6IlUzTQlU8dQCsZOd5FqGxmH/nvIVufC1WCauwfHP0hEIx0F631i2l/DeZRhYj
7SO+idIwHljKyiDgS+CtKygSXjEnwOqV9rVQiLWYrCu0+wXBv2WIDH66xPRnYA3F
WM3MI3ViYekCw2jWLrkaM5sjgfQ/FhTpEFC8uCJXYBF6/FggCEfkd+Yp7G9RnXq+
ZbezRw0HCNmm7inWWGW3hfaVUFS3QVapoppJTDAAsUCspj+TQ9NkbVWdqIqCqUtU
GFgVzwMwSgoW8rekF4A4VxE9IAWPfh9KVKT6JVIYizx0Z/F7P+VmTAvbTlHZGHYX
QtMzyDyIpj0FtZ7yL+6LIywGR4zOP37d97xlKiYQS2JAZMiLnDr0v+avY/Ps/rmV
fFC0sNwctD22gXIW+OecEOEckv/dSIL2PlzZ2gSuJ5xGzyfw2OPa6C1CaoD7y3qn
xbv0zY2jBvm5hLBG/GgorlSkQOyQwLupUYl8hf5EVNjjrOcWk0/Se7Pp2HMp+RrG
krnc4CNhfmyiJxd7GvVA23GHUgC4jMOq6P0qlUu2XcDDQC/jnbs=
=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Re-enable the guest-agent test
- Add the possibility to load a bios image on the mcf5208evb machine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Lzgr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-02-28' into staging
- Updates to MAINTAINERS file
- Re-enable the guest-agent test
- Add the possibility to load a bios image on the mcf5208evb machine
# gpg: Signature made Thu 28 Feb 2019 12:23:25 GMT
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-02-28:
hw/m68k/mcf5208: Support loading of bios images
tests/test-qga: Reenable guest-agent qtest
MAINTAINERS: Clean up the RISC-V TCG backend section
MAINTAINERS: Add some missing entries for the sun4m machine
MAINTAINERS: Add maintainer to the TCG/i386 subsystem
MAINTAINERS: Add maintainers to the Linux subsystem
MAINTAINERS: Orphanize the 'GDB stub' subsystem
MAINTAINERS: Add maintainer to the POSIX subsystem
MAINTAINERS: Add an entry for the Dino machine
MAINTAINERS: Add missing test entries to the Cryptography section
MAINTAINERS: Add missing entries for the QObject section
MAINTAINERS: Add missing entries for the PC machines
MAINTAINERS: Add missing entries for the sun4u machines
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
-----BEGIN PGP SIGNATURE-----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=7MnB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190228-1' into staging
target-arm queue:
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
# gpg: Signature made Thu 28 Feb 2019 11:06:55 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190228-1:
linux-user: Enable HWCAP_ASIMDFHM, HWCAP_JSCVT
target/arm: Enable ARMv8.2-FHM for -cpu max
target/arm: Implement VFMAL and VFMSL for aarch32
target/arm: Implement FMLAL and FMLSL for aarch64
target/arm: Add helpers for FMLAL
Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
target/arm: Gate "miscellaneous FP" insns by ID register field
target/arm: Use MVFR1 feature bits to gate A32/T32 FP16 instructions
hw/arm/armsse: Unify init-svtor and cpuwait handling
hw/arm/iotkit-sysctl: Implement CPUWAIT and INITSVTOR*
hw/arm/iotkit-sysctl: Add SSE-200 registers
hw/misc/iotkit-sysctl: Correct typo in INITSVTOR0 register name
target/arm/arm-powerctl: Add new arm_set_cpu_on_and_reset()
target/arm/cpu: Allow init-svtor property to be set after realize
hw/arm/armsse: Wire up the MHUs
hw/misc/armsse-mhu.c: Model the SSE-200 Message Handling Unit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The locally allocated QDict-s need to be freed. ('file_layer' will be
freed implicitly since it is added as an object to 'driver_layer').
Spotted by Coverity: CID 1398649
While in the neighbourhood free 'driver' and 'filename' as soon as they are
added to the QDicts. Freeing after the 'done' label doesn't make that much
sense as, if the error path jumps to that label, the values would be NULL
anyway.
This patch also makes that more obvious by taking the error path if
'params' is NULL and then asserting that both driver and filename are
non-NULL in the normal path.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190219163440.15702-1-paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The function needs to make sure it is passed a valid disk name. This is
easily done by making sure that the parsing loop results in a non-zero
value.
Spotted by Coverity: CID 1398640
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The assignment to 'p' is unnecessary as the code will either goto 'invalid'
or p will get overwritten.
Spotted by Coverity: CID 1398638
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-3-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The if() statement is clearly bogus (dead code which should have been
cleaned up when grant mapping was removed).
Spotted by Coverity: CID 1398635
While in the neighbourhood, add a missing 'fall through' annotation.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-2-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The MCF5208EVB supports 2 MiB of flash at address 0. Add support
for this memory region and some code to load the file that can
be specified with the "-bios" command line option.
This can be used for example to load U-Boot images for the
MCF5208EVB (we still lack some features in the CPU emulation for
this firmware, though, so it can not be run successfully yet).
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
At the moment the handling of init-svtor and cpuwait initial
values is split between armsse.c and iotkit-sysctl.c:
the code in armsse.c sets the initial state of the CPU
object by setting the init-svtor and start-powered-off
properties, but the iotkit-sysctl.c code has its own
code setting the reset values of its registers (which are
then used when updating the CPU when the guest makes
runtime changes).
Clean this up by making the armsse.c code set properties on the
iotkit-sysctl object to define the initial values of the
registers, so they always match the initial CPU state,
and update the comments in armsse.c accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-9-peter.maydell@linaro.org
The CPUWAIT register acts as a sort of power-control: if a bit
in it is 1 then the CPU will have been forced into waiting
when the system was reset (which in QEMU we model as the
CPU starting powered off). Writing a 0 to the register will
allow the CPU to boot (for QEMU, we model this as powering
it on). Note that writing 0 to the register does not power
off a CPU.
For this to work correctly we need to also honour the
INITSVTOR* registers, which let the guest control where the
CPU will load its SP and PC from when it comes out of reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-8-peter.maydell@linaro.org
The SYSCTL block in the SSE-200 has some extra registers that
are not present in the IoTKit version. Add these registers
(as reads-as-written stubs), enabled by a new QOM property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-7-peter.maydell@linaro.org
The iotkit-sysctl device has a register it names INITSVRTOR0.
This is actually a typo present in the IoTKit documentation
and also in part of the SSE-200 documentation: it should be
INITSVTOR0 because it is specifying the initial value of the
Secure VTOR register in the CPU. Correct the typo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-6-peter.maydell@linaro.org
Create and connect the MHUs in the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-3-peter.maydell@linaro.org
Implement a model of the Message Handling Unit (MHU) found in
the Arm SSE-200. This is a simple device which just contains
some registers which allow the two cores of the SSE-200
to raise interrupts on each other.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-2-peter.maydell@linaro.org
Next set of patches for ppc and spapr. There's a lot in this one:
* Support "STOP light" states on POWER9
* Add support for HVI interrupts on POWER9 (powernv machine)
* CVE-2019-8934: Don't leak host model and serial information to the guest
* Tests and cleanups for various hot unplug options
* Hash and radix MMU implementation on POWER9 for powernv machine
* PCI Host Bridge hotplug support for pseries machine
* Allow larger kernels and initrds for powernv machine
Plus a handful of miscellaneous fixes and cleanups.
The cpu hotplug tests and cleanups from David Hildenbrand aren't
solely power related. However the consensus amongst Michael Tsirkin,
David Hildenbrand, Cornelia Huck and myself was that it made most
sense to come in via my tree.
-----BEGIN PGP SIGNATURE-----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=Z4Z6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190226' into staging
ppc patch queue 2019-02-26
Next set of patches for ppc and spapr. There's a lot in this one:
* Support "STOP light" states on POWER9
* Add support for HVI interrupts on POWER9 (powernv machine)
* CVE-2019-8934: Don't leak host model and serial information to the guest
* Tests and cleanups for various hot unplug options
* Hash and radix MMU implementation on POWER9 for powernv machine
* PCI Host Bridge hotplug support for pseries machine
* Allow larger kernels and initrds for powernv machine
Plus a handful of miscellaneous fixes and cleanups.
The cpu hotplug tests and cleanups from David Hildenbrand aren't
solely power related. However the consensus amongst Michael Tsirkin,
David Hildenbrand, Cornelia Huck and myself was that it made most
sense to come in via my tree.
# gpg: Signature made Tue 26 Feb 2019 03:37:46 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190226: (50 commits)
ppc/pnv: use IEC binary prefixes to represent sizes
ppc/pnv: add INITRD_MAX_SIZE constant
ppc/pnv: increase kernel size limit to 256MiB
hw/ppc: Use object_initialize_child for correct reference counting
ppc/xive: xive does not have a POWER7 interrupt model
tests/device-plug: Add PHB unplug request test for spapr
spapr: enable PHB hotplug for default pseries machine type
spapr: add hotplug hooks for PHB hotplug
spapr_pci: add ibm, my-drc-index property for PHB hotplug
spapr_pci: provide node start offset via spapr_populate_pci_dt()
spapr_events: add support for phb hotplug events
spapr: populate PHB DRC entries for root DT node
spapr: create DR connectors for PHBs
spapr_pci: add PHB unrealize
spapr_irq: Expose the phandle of the interrupt controller
spapr: Expose the name of the interrupt controller node
xics: Write source state to KVM at claim time
spapr/drc: Drop spapr_drc_attach() fdt argument
spapr/pci: Generate FDT fragment at configure connector time
spapr: Generate FDT fragment for CPUs at configure connector time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reset the contents to init data and reset the offset on a machine
reset.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Transfer the state of the EEPROM on a migration. This way the
data remains consistent on migration.
This required moving the actual data to a separate array and
using the data provided in the init function as a separate
initialization array, since a pointer property has to be a
void * and the array needs to be uint8_t[].
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It was hard-coded to 256 in a number of places, create a constant
for that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Create a type name and a cast macro and use those through the
code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
There is no vmstate handling for SMBus, so no device sitting on SMBus
can have a state transfer that works reliably. So add it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Transfer the state information for the SMBus registers and
internal data so it will work on a VM transfer.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The I2C block read function of pm_smbus was completely broken. It
required doing some direct I2C handling because it didn't have a
defined size, the OS code just reads bytes until it marks the
transaction finished.
This also required adjusting how the AMIBIOS workaround code worked,
the I2C block mode was setting STS_HOST_BUSY during a transaction,
so that bit could no longer be used to inform the host status read
code to start the transaction. Create a explicit bool for that
operation.
Also, don't read the next byte from the device in byte-by-byte
mode unless the OS is actually clearing the byte done bit. Just
assuming that's what the OS is doing is a bad idea.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Migration capability is being added for pm_smbus and SMBus devices.
This change will allow backwards compatibility to be kept when
migrating back to an old qemu version. Add a bool to the machine
class tho keep smbus migration from happening. Future changes
will use this.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There were two different read functions, and with the removal of
the command passed in there is no functional difference. So remove
one of them. With that you don't need one of the states, so that
can be removed, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There were two different write functions and the SMBus code kept
track of the command.
Keeping track of the command wasn't useful, in fact it wasn't quite
correct for the eeprom_smbus code. And there is no need for two write
functions. Just have one write function and the first byte in the
buffer is the command.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The logic of handling quick SMBus commands was wrong. If you get a
finish event with no data, that's a quick command.
Document the quick command while we are at it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
i2c_recv() cannot fail, so there is no need to check the return
value. It also returns unt8_t, so comparing with < 0 is not
meaningful.
Fix up various I2C controllers to remove the unneeded code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
It can't fail, and now that it returns a uint8_t a 0xff mask
is unnecessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
- Block graph change fixes (avoid loops, cope with non-tree graphs)
- bdrv_set_aio_context() related fixes
- HMP snapshot commands: Use only tag, not the ID to identify snapshots
- qmeu-img, commit: Error path fixes
- block/nvme: Build fix for gcc 9
- MAINTAINERS updates
- Fix various issues with bdrv_refresh_filename()
- Fix various iotests
- Include LUKS overhead in qemu-img measure for qcow2
- A fix for vmdk's image creation interface
-----BEGIN PGP SIGNATURE-----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=gaah
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Block graph change fixes (avoid loops, cope with non-tree graphs)
- bdrv_set_aio_context() related fixes
- HMP snapshot commands: Use only tag, not the ID to identify snapshots
- qmeu-img, commit: Error path fixes
- block/nvme: Build fix for gcc 9
- MAINTAINERS updates
- Fix various issues with bdrv_refresh_filename()
- Fix various iotests
- Include LUKS overhead in qemu-img measure for qcow2
- A fix for vmdk's image creation interface
# gpg: Signature made Mon 25 Feb 2019 14:18:15 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (71 commits)
iotests: Skip 211 on insufficient memory
vmdk: false positive of compat6 with hwversion not set
iotests: add LUKS payload overhead to 178 qemu-img measure test
qcow2: include LUKS payload overhead in qemu-img measure
iotests.py: s/_/-/g on keys in qmp_log()
iotests: Let 045 be run concurrently
iotests: Filter SSH paths
iotests.py: Filter filename in any string value
iotests.py: Add is_str()
iotests: Fix 207 to use QMP filters for qmp_log
iotests: Fix 232 for LUKS
iotests: Remove superfluous rm from 232
iotests: Fix 237 for Python 2.x
iotests: Re-add filename filters
iotests: Test json:{} filenames of internal BDSs
block: BDS options may lack the "driver" option
block/null: Generate filename even with latency-ns
block/curl: Implement bdrv_refresh_filename()
block/curl: Harmonize option defaults
block/nvme: Fix bdrv_refresh_filename()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The internal inotify APIs allow a lot of conditional statements to be
cleared out, and provide a simpler callback for handling events.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Various functions accepting 'char *' string parameters were missing
'const' qualifiers.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
IN_ISDIR is not a bit that one can request when registering a
watch with inotify_add_watch. Rather it is a bit that is set
automatically when reading events from the kernel.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Using IEC binary prefixes from qemu/units.h provides a more human-friendly value
to size constants.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-4-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current 0x10000000 value is actually 256MiB, not 128MB as the comment
suggests. Move it to a constant and fix the comment (no change in the size
value).
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-3-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Building kernel with CONFIG_DEBUG_INFO_REDUCED can generate a ~90MB image and
building with CONFIG_DEBUG_INFO can generate a ~225M one, both exceeds the
current limit of 32MiB.
Increasing kernel size limit to 256MiB should fit for now.
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-2-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Both functions, object_initialize() and object_property_add_child() increase
the reference counter of the new object, so one of the references has to be
dropped afterwards to get the reference counting right. Otherwise the child
object will not be properly cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the reference
counting here right.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1550748288-30598-1-git-send-email-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Patch "target/ppc: Add POWER9 external interrupt model" should have
removed the section covering PPC_FLAGS_INPUT_POWER7.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190219142530.17807-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'dr_phb_enabled' field of that class can be set as part of
machine-specific init code. It will be used to conditionally
enable creation of DRC objects and device-tree description to
facilitate hotplug of PHBs.
Since we can't migrate this state to older machine types,
default the option to true and disable it for older machine
types.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059673433.1466090.6188091133769611501.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hotplugging PHBs is a machine-level operation, but PHBs reside on the
main system bus, so we register spapr machine as the handler for the
main system bus.
Provide the usual pre-plug, plug and unplug-request handlers.
Move the checking of the PHB index to the pre-plug handler. It is okay
to do that and assert in the realize function because the pre-plug
handler is always called, even for the oldest machine types we support.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
(Fixed interrupt controller phandle in "interrupt-map" and
TCE table size in "ibm,dma-window" FDT fragment, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059672926.1466090.13612804072190051439.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is needed to denote a boot-time PHB as being hot-pluggable.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059672420.1466090.15147504040270659866.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug re-uses PHB device tree generation code and passes
it to a guest via RTAS. Doing this requires knowledge of where
exactly in the device tree the node describing the PHB begins.
Provide this via a new optional pointer that can be used to
store the PHB node's start offset.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059671912.1466090.10891589403973703473.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Extend the existing EPOW event format we use for PCI
devices to emit PHB plug/unplug events.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059671405.1466090.535964535260503283.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This add entries to the root OF node to advertise our PHBs as being
DR-capable in accordance with PAPR specification.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059670897.1466090.10843921337591637414.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059670389.1466090.10015601248906623076.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support PHB hotplug we need to clean up lingering references,
memory, child properties, etc. prior to the PHB object being
finalized. Generally this will be called as a result of calling
object_unparent() on the PHB object, which in turn would normally
be called as the result of an unplug() operation.
When the PHB is finalized, child objects will be unparented in
turn, and finalized if the PHB was the only reference holder. so
we don't bother to explicitly unparent child objects of the PHB,
with the notable exception of DRCs. This is needed to avoid a QEMU
crash when unplugging a PHB and resetting the machine before the
guest could handle the event. The DRCs are removed from the QOM tree
by pci_unregister_root_bus() and we must make sure we're not leaving
stale aliases under the global /dr-connector path.
The formula that gives the number of DMA windows is moved to an
inline function in the hw/pci-host/spapr.h header because it
will have other users.
The unrealize function is able to cope with partially realized PHBs.
It is hence used to implement proper rollback on the realize error
path.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059669881.1466090.13515030705986041517.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used by PHB hotplug in order to create the "interrupt-map"
property of the PHB node.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059669374.1466090.12943228478046223856.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be needed by PHB hotplug in order to access the "phandle"
property of the interrupt controller node.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059668867.1466090.6339199751719123386.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine only uses LSIs to support legacy PCI devices. Every
PHB claims 4 LSIs at realize time. When using in-kernel XICS (or upcoming
in-kernel XIVE), QEMU synchronizes the state of all irqs, including these
LSIs, later on at machine reset.
In order to support PHB hotplug, we need a way to tell KVM about the LSIs
that doesn't require a machine reset. An easy way to do that is to always
inform KVM when an interrupt is claimed, which really isn't a performance
path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059668360.1466090.5969630516627776426.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All DRC subtypes have been converted to generate the FDT fragment at
configure connector time instead of attach time. The fdt and fdt_offset
arguments of spapr_drc_attach() aren't needed anymore. Drop them and
make the implementation of the dt_populate() method mandatory.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059667853.1466090.16527852453054217565.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059667346.1466090.326696113231137772.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666839.1466090.3833376527523126752.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666331.1466090.6766540766297333313.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current logic is to provide the FDT fragment when attaching a device
to a DRC. This works perfectly fine for our current hotplug support, but
soon we will add support for PHB hotplug which has some constraints, that
CPU, PCI and LMB devices don't seem to have.
The first constraint is that the "ibm,dma-window" property of the PHB
node requires the IOMMU to be configured, ie, spapr_tce_table_enable()
has been called, which happens during PHB reset. It is okay in the case
of hotplug since the device is reset before the hotplug handler is
called. On the contrary with coldplug, the hotplug handler is called
first and device is only reset during the initial system reset. Trying
to create the FDT fragment on the hotplug path in this case, would
result in somthing like this:
ibm,dma-window = < 0x80000000 0x00 0x00 0x00 0x00 >;
This will cause linux in the guest to panic, by simply removing and
re-adding the PHB using the drmgr command:
page = alloc_pages_node(nid, GFP_KERNEL, get_order(sz));
if (!page)
panic("iommu_init_table: Can't allocate %ld bytes\n", sz);
The second and maybe more problematic constraint is that the
"interrupt-map" property needs to reference the interrupt controller
node using the very same phandle that SLOF has already exposed to the
guest. QEMU requires SLOF to call the private KVMPPC_H_UPDATE_DT hcall
at some point to know about this phandle. With the latest QEMU and SLOF,
this happens when SLOF gets quiesced. This means that if the PHB gets
hotplugged after CAS but before SLOF quiesce, then we're sure that the
phandle is not known when the hotplug handler is called.
The FDT is only needed when the guest first invokes RTAS to configure
the connector actually, long after SLOF quiesce. Let's postpone the
creation of FDT fragments for PHBs to rtas_ibm_configure_connector().
Since we only need this for PHBs, introduce a new method in the base
DRC class for that. DRC subtypes will be converted to use it in
subsequent patches.
Allow spapr_drc_attach() to be passed a NULL fdt argument if the method
is available. When all DRC subtypes have been converted, the fdt argument
will eventually disappear.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059665823.1466090.18358845122627355537.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
That "b" means "base address" and thus shouldn't be in the name
of actual entries and related constants.
This patch keeps the synthetic patb_entry field of the spapr
virtual hypervisor unchanged until I figure out if that has
an impact on the migration stream.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With mttcg, we can have MMU lookups happening at the same time
as the guest modifying the page tables.
Since the HPTEs of the hash table MMU contains two words (or
double worlds on 64-bit), we need to make sure we read them
in the right order, with the correct memory barrier.
Additionally, when using emulated SPAPR mode, the hypercalls
writing to the hash table must also perform the udpates in
the right order.
Note: This part is still not entirely correct
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The HW relies on LPCR:HR along with the PATE to determine whether
to use Radix or Hash mode. In fact it uses LPCR:HR more commonly
than the PATE.
For us, it's also more efficient to do so, especially since unlike
the HW we do not maintain a cache of the current PATE and HV PATE
in a generic place.
Prepare the grounds for that by ensuring that LPCR:HR is set
properly on SPAPR machines.
Another option would have been to use a callback to get the PATE
but this gets messy when implementing bare metal support, it's
much simpler (and faster) to use LPCR.
Since existing migration streams may not have it, fix it up in
spapr_post_load() as well based on the pseudo-PATE entry that
we keep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fake availability of OV5_HP_EVT, so we can test memory unplug in qtest.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190218092202.26683-3-david@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On ppc hosts, hypervisor shares following system attributes
- /proc/device-tree/system-id
- /proc/device-tree/model
with a guest. This could lead to information leakage and misuse.[*]
Add machine attributes to control such system information exposure
to a guest.
[*] https://wiki.openstack.org/wiki/OSSN/OSSN-0028
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Fix-suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20190218181349.23885-1-ppandit@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To better reflect what this does, as it's specific to some of the
P7/P8/P9 PM states, not generic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccAIFAAoJEJykq7OBq3PImM0IAMcC92GYwSL6MgQ4NrfbVfDQ
P+qgIoxlXcYNwa12kGY6rE4tgSDab9Mc5ACpmuFdr8Xj7/JOp97AccmKZ+RzYQSj
IFlkvd8GngQR1YnFGV6PIWSt7hRhKuUZMqSIDrWro/MTdiJFEMI8/e7QLGxmaEX1
gWCNSopxJUeACSJiRyfZvBGNCs23R9ptFKBFhIXS98KPtEtF8LQV0JnQXoRUDiBL
G9C/xggdGDvct3Id4yOBCh43ErssyOrlYwjzIRWB2AFfIwHGytJcL6JBjAqy4Z7M
ClMNXaQSbfSCXrc3osF9nO6KaFduhfpUH44lL5JBHxUgH6pN2xGradRANZwysQM=
=DSBn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
Pull request
# gpg: Signature made Fri 22 Feb 2019 14:07:01 GMT
# gpg: using RSA key 9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request: (27 commits)
tests/virtio-blk: add test for DISCARD command
tests/virtio-blk: add test for WRITE_ZEROES command
tests/virtio-blk: add virtio_blk_fix_dwz_hdr() function
tests/virtio-blk: change assert on data_size in virtio_blk_request()
virtio-blk: add DISCARD and WRITE_ZEROES features
virtio-blk: set config size depending on the features enabled
virtio-net: make VirtIOFeature usable for other virtio devices
virtio-blk: add "discard" and "write-zeroes" properties
virtio-blk: add host_features field in VirtIOBlock
virtio-blk: add acct_failed param to virtio_blk_handle_rw_error()
hw/ide: drop iov field from IDEDMA
hw/ide: drop iov field from IDEBufferedRequest
hw/ide: drop iov field from IDEState
tests/test-bdrv-drain: use QEMU_IOVEC_INIT_BUF
migration/block: use qemu_iovec_init_buf
qemu-img: use qemu_iovec_init_buf
block/vmdk: use qemu_iovec_init_buf
block/qed: use qemu_iovec_init_buf
block/qcow2: use qemu_iovec_init_buf
block/qcow: use qemu_iovec_init_buf
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_blk_dma_restart_bh() submits new requests, so in order to make
sure that these requests are not started inside a drained section of the
attached BlockBackend, we need to make sure that draining the
BlockBackend waits for the BH to be executed.
This BH is still questionable because its scheduled in the main thread
instead of the configured iothread. Leave a FIXME comment for this.
But with this fix, enabling the data plane at least waits for these
requests (in bdrv_set_aio_context()) instead of changing the AioContext
under their feet and making them run in the wrong thread, causing
crashes and failures (e.g. due to missing locking).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cppcheck reports:
[hw/tpm/tpm_tis.c:113]: (warning) %d in format string (no. 2) requires 'int' but the argument type is 'unsigned int'
Rather than just converting the format specifier to use '%u", the
tpm_tis_show_buffer() function is converted to use trace points and
the two debug callers use the trace event infrastructure so that it's
available in production cases also and not just when DEBUG_TIS is enabled.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
In tpm_tis_mmio_write() if the requesting locality is seizing
access, any seizure by a lower locality is cancelled. However the
loop doing the seizure had an off-by-one error and the locality
immediately preceding the requesting locality was not being cleared.
This is fixed by adjusting the test in the for loop to check the
localities up to the requesting locality.
Signed-off-by: Liam Merwick <Liam.Merwick@oracle.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
The entire link status register for SR-IOV VFs is defined as RsvdZ,
reads simply return zero. Usually this is nothing more than lspci
reporting inconsequentially broken values:
LnkSta: Speed unknown, Width x0, ...
However, now that we're using the downstream endpoint link status to
fill in the value at the parent downstream port, invalid values become
a problem. In particular, the PCIe hotplug driver in Linux looks for
a valid negotiated link width and will fail to enumerate hot-added
downstream endpoints without non-zero value here, ex:
pciehp 0000:00:02.0:pcie004: Slot(0): Attention button pressed
pciehp 0000:00:02.0:pcie004: Slot(0) Powering on due to button press
pciehp 0000:00:02.0:pcie004: Slot(0): Card present
pciehp 0000:00:02.0:pcie004: Slot(0): Link Up
pciehp 0000:00:02.0:pcie004: link training error: status 0x2000
pciehp 0000:00:02.0:pcie004: Failed to check link status
Resolve by using minimum width and speed values for the downstream
port link status when the endpoint fails to provide valid values.
Long term, we may want to implement emulation in the vfio-pci host
driver to suppliment this field with the PF value as the SR-IOV spec
seems to allow, but the solution here is compatible should that be
implemented later.
Fixes: 727b48661f ("pci: Sync PCIe downstream port LNKSTA on read")
Reported-by: Jens Freimann <jfreimann@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <155060310248.19547.14979269067689441201.stgit@gimli.home>
Tested-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The type 3 SMBIOS structure[1] ends with fields
...
0x14 - contained element count
0x15 - contained element record length
0x16 - sku number
The smbios_type_3 struct missed the contained element record
length field, causing sku number to be reported at the wrong
offset.
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.1.1.pdf
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190215153600.1770727-1-berrange@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Fixes: e41fca3da7
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
sPAPR code will use it too so move it from VFIO to the common code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190214051440.59167-1-aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio-balloon always works in units of 4kiB (BALLOON_PAGE_SIZE), but
we can only actually discard memory in units of the host page size.
Now, we handle this very badly: we silently ignore balloon requests that
aren't host page aligned, and for requests that are host page aligned we
discard the entire host page. The latter can corrupt guest memory if its
page size is smaller than the host's.
The obvious choice would be to disable the balloon if the host page size is
not 4kiB. However, that would break the special case where host and guest
have the same page size, but that's larger than 4kiB. That case currently
works by accident[1] - and is used in practice on many production POWER
systems where 64kiB has long been the Linux default page size on both host
and guest.
To make the balloon safe, without breaking that useful special case, we
need to accumulate 4kiB balloon requests until we have a whole contiguous
host page to discard.
We could in principle do that across all guest memory, but it would require
a large bitmap to track. This patch represents a compromise: we track
ballooned subpages for a single contiguous host page at a time. This means
that if the guest discards all 4kiB chunks of a host page in succession,
we will discard it. This is the expected behaviour in the (host page) ==
(guest page) != 4kiB case we want to support.
If the guest scatters 4kiB requests across different host pages, we don't
discard anything, and issue a warning. Not ideal, but at least we don't
corrupt guest memory as the previous version could.
Warning reporting is kind of a compromise here. Determining whether we're
in a problematic state at realize() time is tricky, because we'd have to
look at the host pagesizes of all memory backends, but we can't really know
if some of those backends could be for special purpose memory that's not
subject to ballooning.
Reporting only when the guest tries to balloon a partial page also isn't
great because if the guest page size happens to line up it won't indicate
that we're in a non ideal situation. It could also cause alarming repeated
warnings whenever a migration is attempted.
So, what we do is warn the first time the guest attempts balloon a partial
host page, whether or not it will end up ballooning the rest of the page
immediately afterwards.
[1] Because when the guest attempts to balloon a page, it will submit
requests for each 4kiB subpage. Most will be ignored, but the one
which happens to be host page aligned will discard the whole lot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190214043916.22128-6-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcbu/QAAoJENSXKoln91plb0oH/RczDVACfmhnERAru8NhW19/
6YB5w1FjbH+CkNB4ZBdF5sQNRyAnuHxL6xMKT3LvZUCEy0ADk+D5KJxzg340JABB
eGc2FxKYe1vbhCAsYhQMOZyGhiye6UZnRjTXirYqMCm74zuFVI954X0V1ytfHARI
0AIsWcOOVLnJj+itU0Uj+i+dBFFec0TbHWodvB8rt+TVcg5SFsdiwbT7jLxUSCAA
VwhjmDUlE2+545LgbIrRbhMfnsEDkMgN2C1YGqkdBSM03dYnW0scxudGbxN0QPrV
l0KAVTvUXcdUj0i1B3E91QiF0s6KU34TpE1vwZFUBdyuqHpIPgNhJkK6Tmt/DqM=
=PVKW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amarkovic/tags/mips-queue-feb-21-2019-v2' into staging
MIPS queue for February 21st, 2019, v2
# gpg: Signature made Thu 21 Feb 2019 18:37:04 GMT
# gpg: using RSA key D4972A8967F75A65
# gpg: Good signature from "Aleksandar Markovic <amarkovic@wavecomp.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8526 FBF1 5DA3 811F 4A01 DD75 D497 2A89 67F7 5A65
* remotes/amarkovic/tags/mips-queue-feb-21-2019-v2:
target/mips: fulong2e: Dynamically generate SPD EEPROM data
target/mips: fulong2e: Fix bios flash size
hw/pci-host/bonito.c: Add PCI mem region mapped at the correct address
target/mips: implement QMP query-cpu-definitions command
tests/tcg: target/mips: Add wrappers for MSA integer compare instructions
tests/tcg: target/mips: Change directory name 'bit-counting' to 'bit-count'
tests/tcg: target/mips: Correct path to headers in some test source files
hw/misc: mips_itu: Fix 32/64 bit issue in a line involving shift operator
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the support of DISCARD and WRITE_ZEROES commands,
that have been introduced in the virtio-blk protocol to have
better performance when using SSD backend.
We support only one segment per request since multiple segments
are not widely used and there are no userspace APIs that allow
applications to submit multiple segments in a single call.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-7-sgarzare@redhat.com
Message-Id: <20190221103314.58500-7-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Starting from DISABLE and WRITE_ZEROES features, we use an array of
VirtIOFeature (as virtio-net) to properly set the config size
depending on the features enabled.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-6-sgarzare@redhat.com
Message-Id: <20190221103314.58500-6-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In order to use VirtIOFeature also in other virtio devices, we move
its declaration and the endof() macro (renamed in virtio_endof())
in virtio.h.
We add virtio_feature_get_config_size() function to iterate the array
of VirtIOFeature and to return the config size depending on the
features enabled. (as virtio_net_set_config_size() did)
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-5-sgarzare@redhat.com
Message-Id: <20190221103314.58500-5-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In order to avoid migration issues, we enable DISCARD and
WRITE_ZEROES features only for machine type >= 4.0
As discussed with Michael S. Tsirkin and Stefan Hajnoczi on the
list [1], DISCARD operation should not have security implications
(eg. page cache attacks), so we can enable it by default.
[1] https://lists.gnu.org/archive/html/qemu-devel/2019-02/msg00504.html
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-4-sgarzare@redhat.com
Message-Id: <20190221103314.58500-4-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since configurable features for virtio-blk are growing, this patch
adds host_features field in the struct VirtIOBlock. (as in virtio-net)
In this way, we can avoid to add new fields for new properties and
we can directly set VIRTIO_BLK_F* flags in the host_features.
We update "config-wce" and "scsi" property definition to use the new
host_features field without change the behaviour.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-3-sgarzare@redhat.com
Message-Id: <20190221103314.58500-3-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We add acct_failed param in order to use virtio_blk_handle_rw_error()
also when is not required to call block_acct_failed(). (eg. a discard
operation is failed)
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-2-sgarzare@redhat.com
Message-Id: <20190221103314.58500-2-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-18-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-18-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-17-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-17-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-16-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-16-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds EDID support to the family of virtio-gpu devices. It is
turned off by default, use the new edid property to enable it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190221081054.13853-1-kraxel@redhat.com
We introduce the vfio_init_container_type() helper.
It computes the highest usable iommu type and then
set the container and the iommu type.
Its usage in vfio_connect_container() makes the code
ready for addition of new iommu types.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
A kernel bug was introduced in v4.15 via commit 71a7d3d78e3c which
adds a test for address space wrap-around in the vfio DMA unmap path.
Unfortunately due to overflow, the kernel detects an unmap of the last
page in the 64-bit address space as a wrap-around. In QEMU, a Q35
guest with VT-d emulation and guest IOMMU enabled will attempt to make
such an unmap request during VM system reset, triggering an error:
qemu-kvm: VFIO_UNMAP_DMA: -22
qemu-kvm: vfio_dma_unmap(0x561f059948f0, 0xfef00000, 0xffffffff01100000) = -22 (Invalid argument)
Here the IOVA start address (0xfef00000) and the size parameter
(0xffffffff01100000) add to exactly 2^64, triggering the bug. A
kernel fix is queued for the Linux v5.0 release to address this.
This patch implements a workaround to retry the unmap, excluding the
final page of the range when we detect an unmap failing which matches
the requirements for this issue. This is expected to be a safe and
complete workaround as the VT-d address space does not extend to the
full 64-bit space and therefore the last page should never be mapped.
This workaround can be removed once all kernels with this bug are
sufficiently deprecated.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1662291
Reported-by: Pei Zhang <pezhang@redhat.com>
Debugged-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The machine comes with 256M memory module by default but it's
upgradable so it could have different memory size. There was a TODO
comment to replace static SPD EEPROM data with dynamically generated
one to support this. Now that we have a function for that, it's easy
to do. Although this would allow larger RAM sizes, the peculiar memory
map of the machine may need some special handling to map it as low and
high memory. Because I don't know what the correct place would be for
highmem, I've left memory size fixed at 256M for now and TODO is moved
there instead.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
According to both the specifications on linux-mips.org referenced in a
comment at the beginning of the file and the flash chip part number
the bios size should be 512k not 1M.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Stop using system memory as PCI memory otherwise devices such as VGA
that have regions mapped to PCI memory clash with RAM. Use a separate
memory region for PCI memory and map it to the correct address in
system memory which allows PCI mem regions to show at the correct
address where clients expect them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Fix 32/64 bit issue in a line involving shift operator. "1 << ..."
calculation of size is done as a 32-bit signed integer which may
then be unintentionally sign-extended into the 64-bit result. The
problem was discovered by Coverity (CID 1398648). Using "1ULL"
instead of "1" on the LHS of the shift fixes this problem.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The region 0x40010000 .. 0x4001ffff and its secure-only alias
at 0x50010000... are for per-CPU devices. We implement this by
giving each CPU its own container memory region, where the
per-CPU devices live. Unfortunately, the alias region which
makes devices mapped at 0x4... addresses also appear at 0x5...
is only implemented in the overall "all CPUs" container. The
effect of this bug is that the CPU_IDENTITY register block appears
only at 0x4001f000, but not at the 0x5001f000 alias where it should
also appear. Guests (like very recent Arm Trusted Firmware-M)
which try to access it at 0x5001f000 will crash.
Fix this by moving the handling for this alias from the "all CPUs"
container to the per-CPU container. (We leave the aliases for
0x1... and 0x3... in the overall container, because there are
no per-CPU devices there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190215180500.6906-1-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Wire up the two PL011 UARTs in the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the PL031 RTC for the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca board puts its SRAM and flash behind TrustZone
Memory Protection Controllers (MPCs). Each MPC sits between
the CPU and the RAM/flash, and also has a set of memory mapped
control registers. Wire up the MPCs, and the memory behind them.
For the moment we implement the flash as simple ROM, which
cannot be reprogrammed by the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Many of the devices on the Musca board live behind TrustZone
Peripheral Protection Controllers (PPCs); add models of the
PPCs, using a similar scheme to the MPS2 board models.
This commit wires up the PPCs with "unimplemented device"
stubs behind them in the correct places in the address map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca-A and Musca-B1 development boards are based on the
SSE-200 subsystem for embedded. Implement an initial skeleton
model of these boards, which are similar but not identical.
This commit creates the board model with the SSE and the IRQ
splitters to wire IRQs up to its two CPUs. As yet there
are no devices and no memory: these will be added later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The pl011 logs when the guest makes a bad access. It prints
the address offset in hex but confusingly omits the '0x'
prefix; add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL011 UART has six interrupt lines:
* RX (receive data)
* TX (transmit data)
* RT (receive timeout)
* MS (modem status)
* E (errors)
* combined (logical OR of all the above)
So far we have only emulated the combined interrupt line;
add support for the others, so that boards that wire them
up to different interrupt controller inputs can do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl011's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Convert the debug printing in the PL031 device to use trace events,
and augment it to cover the interesting parts of device operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Peripheral Protection Controller's handling of unused ports
is that if there is nothing connected to the port's downstream
then it does not create the sysbus MMIO region for the upstream
end of the port. This results in odd behaviour when there is
an unused port in the middle of the range: since sysbus MMIO
regions are implicitly consecutively allocated, any used ports
above the unused ones end up with sysbus MMIO region numbers
that don't match the port number.
Avoid this numbering mismatch by creating dummy MMIO regions
for the unused ports. This doesn't change anything for our
existing boards, which don't have any gaps in the middle of
the port ranges they use; but it will be needed for the Musca
board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Coverity points out (CID 1398632, CID 1398650) that we
leak a couple of allocated strings in the error-exit
code path for setting up the MHUs in the ARMSSE.
Fix this bug by moving the allocate-and-free of each
string to be closer to the use, so we do the free before
doing the error-exit check.
Fixes: f8574705f6 ("hw/arm/armsse: Add unimplemented-device stubs for MHUs")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190215113707.24553-1-peter.maydell@linaro.org
some versions of HP-UX 10.20 seems to rely on the fact that DINO
strips out the lower 2 bits of the PCI configuration address.
Also update the binary SeaBIOS distributed to the latest version
from Helge's repository, which is required with that change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190218183314.20157-1-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Currently, virtio-balloon uses madvise() with MADV_DONTNEED to actually
discard RAM pages inserted into the balloon. This is basically a Linux
only interface (MADV_DONTNEED exists on some other platforms, but doesn't
always have the same semantics). It also doesn't work on hugepages and has
some other limitations.
It turns out that postcopy also needs to discard chunks of memory, and uses
a better interface for it: ram_block_discard_range(). It doesn't cover
every case, but it covers more than going direct to madvise() and this
gives us a single place to update for more possibilities in future.
There are some subtleties here to maintain the current balloon behaviour:
* For now, we just ignore requests to balloon in a hugepage backed region.
That matches current behaviour, because MADV_DONTNEED on a hugepage would
simply fail, and we ignore the error.
* If host page size is > BALLOON_PAGE_SIZE we can frequently call this on
non-host-page-aligned addresses. These would also fail in madvise(),
which we then ignored. ram_block_discard_range() error_report()s calls
on unaligned addresses, so we explicitly check that case to avoid
spamming the logs.
* We now call ram_block_discard_range() with the *host* page size, whereas
we previously called madvise() with BALLOON_PAGE_SIZE. Surprisingly,
this also matches existing behaviour. Although the kernel fails madvise
on unaligned addresses, it will round unaligned sizes *up* to the host
page size. Yes, this means that if BALLOON_PAGE_SIZE < guest page size
we can incorrectly discard more memory than the guest asked us to. I'm
planning to address that soon.
Errors other than the ones discussed above, will now be reported by
ram_block_discard_range(), rather than silently ignored, which means we
have a much better chance of seeing when something is going wrong.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190214043916.22128-5-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This replaces the balloon_page() internal interface with
ballon_inflate_page(), with a slightly different interface. The new
interface will make future alterations simpler.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190214043916.22128-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio-balloon device's verification of the address given to it by the
guest has a number of faults:
* The addresses here are guest physical addresses, which should be
'hwaddr' rather than 'ram_addr_t' (the distinction is admittedly
pretty subtle and confusing)
* We don't check for section.mr being NULL, which is the main way that
memory_region_find() reports basic failures. We really need to check
that before looking at any other section fields, because
memory_region_find() doesn't initialize them on the failure path
* We're passing a length of '1' to memory_region_find(), but really the
guest is requesting that we put the entire page into the balloon,
so it makes more sense to call it with BALLOON_PAGE_SIZE
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190214043916.22128-3-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the balloon is inflated, we discard memory place in it using madvise()
with MADV_DONTNEED. And when we deflate it we use MADV_WILLNEED, which
sounds like it makes sense but is actually unnecessary.
The misleadingly named MADV_DONTNEED just discards the memory in question,
it doesn't set any persistent state on it in-kernel; all that's necessary
to bring the memory back is to touch it. MADV_WILLNEED in contrast
specifically says that the memory will be used soon and faults it in.
This patch simplify's the balloon operation by dropping the madvise()
on deflate. This might have an impact on performance - it will move a
delay at deflate time until that memory is actually touched, which
might be more latency sensitive. However:
* Memory that's being given back to the guest by deflating the
balloon *might* be used soon, but it equally could just sit around
in the guest's pools until needed (or even be faulted out again if
the host is under memory pressure).
* Usually, the timescale over which you'll be adjusting the balloon
is long enough that a few extra faults after deflation aren't
going to make a difference.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190214043916.22128-2-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[get|set]_addr are two counterpart to access PCDIMMDevice.addr.
Since we have already set up a property PC_DIMM_ADDR_PROP for this
field and use this mechanism in set_addr, it would be more proper to use
the same mechanism in get_addr.
This patch uses object_property_get_uint() to replace the direct memory
access to make [get|set]_addr with the same mechanism.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190211064629.20186-1-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Detect all invalid configurations (e.g. mingw32 with vhost-user,
non-Linux with vhost-kernel). As a collateral benefit, all vhost-kernel
backends can be now disabled if one wants to reduce the attack surface.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1543851204-41186-6-git-send-email-pbonzini@redhat.com>
Message-Id: <1550165756-21617-7-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This shows a preexisting bug: if a KVM target did not have virtio-net enabled,
it would fail with undefined symbols when vhost was enabled. This must now
be fixed, lest targets that have no virtio-net fail to compile.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1543851204-41186-5-git-send-email-pbonzini@redhat.com>
Message-Id: <1550165756-21617-6-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user does not depend on Linux; it can run on any POSIX system. Restrict
vhost-kernel to Linux in hw/virtio/vhost-backend.c, everything else can be
compiled on all POSIX systems.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1543851204-41186-4-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1550165756-21617-4-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/net/vhost_net.c needs functions that are declared in net/vhost-user.c: the
vhost-user code is always compiled into QEMU, only the constructor
net_init_vhost_user is unreachable. Also, net/vhost-user.c needs functions
declared in hw/virtio/vhost-stub.c even if no virtio device exists.
Break this dependency. First, add a minimal version of net/vhost-user.c,
with no functionality and no dependency on vhost code. Second, #ifdef out
the calls back to net/vhost-user.c from hw/net/vhost_net.c.
While at it, this patch fixes the CONFIG_VHOST_NET_USE*D* typo.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1543851204-41186-3-git-send-email-pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1550165756-21617-3-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no reason for CONFIG_VHOST_NET to be specific to a single target;
it is a host feature that can be add to all targets, as long as they support
the virtio-net device. Currently CONFIG_VHOST_NET depends on CONFIG_KVM,
but ioeventfd support is present in the core memory API and works with
other accelerators as well.
As a first step, move the vhost-net stubs to a separate file. Later, they
will become conditional on CONFIG_VIRTIO_NET, which is not available in .c
files.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1543851204-41186-2-git-send-email-pbonzini@redhat.com>
Message-Id: <1550165756-21617-2-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Calls the new SPICE QXL interface function spice_qxl_set_device_info to
set the hardware address of the graphics device represented by the QXL
interface (e.g. a PCI path) and the device display IDs (the IDs of the
device's monitors that belong to this QXL interface).
Also stops using the deprecated spice_qxl_set_max_monitors, the new
interface function replaces it.
Signed-off-by: Lukáš Hrázký <lhrazky@redhat.com>
Message-Id: <20190215150919.8263-1-lhrazky@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
No caller of usb_ep_get() calls it with a NULL device (previous commits
have addressed the few remaining cases which didn't explicitly check).
Replace check for 'dev == NULL' with an assert instead.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-10-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add an assert and an explicit check before the two callers to
usb_ep_get() in the USB redirector code to ensure the device
passed in is not NULL.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-9-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In musb_packet(), the call to usb_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get(). This then
allows the subsequent calculation of 'id' to be streamlined.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-8-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In uhci_handle_td(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-7-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
A call to ohci_find_device() can return NULL if it doesn't find a
device matching 'addr' so for the two callers, explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-6-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In ehci_process_itd(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'devaddr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-5-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most callers of xhci_port_update() and xhci_wakeup() pass in a pointer
to an array entry and can never be NULL but add two defensive asserts
to protect against future changes (e.g. adding a new port speed, etc.)
adding a path through xhci_lookup_port() that could result in the
return of a NULL XHCIPort.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-3-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no need to calculate the 'eps' variable in usb_ep_get()
if 'ep' is the control endpoint. Instead the calculation should
be done after validating the input before returning an entry
indexed by the endpoint 'ep'.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <Darren.Kenny@oracle.com>
Reviewed-by: Mark Kanda <Mark.Kanda@oracle.com>
Reviewed-by: Ameya More <ameya.more@oracle.com>
Message-id: 1549460216-25808-2-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=QQra
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190219' into staging
ppc patch queue 2019-02-19
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
# gpg: Signature made Mon 18 Feb 2019 13:47:54 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190219: (43 commits)
target/ppc: convert vmin* and vmax* to vector operations
target/ppc: convert vadd*s and vsub*s to vector operations
target/ppc: Split out VSCR_SAT to a vector field
target/ppc: Add set_vscr_sat
target/ppc: Use mtvscr/mfvscr for vmstate
target/ppc: Add helper_mfvscr
target/ppc: Remove vscr_nj and vscr_sat
target/ppc: Use helper_mtvscr for reset and gdb
target/ppc: Pass integer to helper_mtvscr
target/ppc: convert xxsel to vector operations
target/ppc: convert xxspltw to vector operations
target/ppc: convert xxspltib to vector operations
target/ppc: convert VSX logical operations to vector operations
target/ppc: convert vsplt[bhw] to use vector operations
target/ppc: convert vspltis[bhw] to use vector operations
target/ppc: convert vaddu[b,h,w,d] and vsubu[b,h,w,d] over to use vector operations
target/ppc: convert VMX logical instructions to use vector operations
xics: Drop the KVM ICS class
spapr/irq: Use the "simple" ICS class for KVM
xics: Handle KVM interrupt presentation from "simple" ICS code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=pNCA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2019-02-18' into staging
QAPI patches for 2019-02-18
# gpg: Signature made Mon 18 Feb 2019 13:44:30 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2019-02-18:
qapi: move RTC_CHANGE to the target schema
qmp: Deprecate query-events in favor of query-qmp-schema
Revert "qapi-events: add 'if' condition to implicit event enum"
qapi: remove qmp_unregister_command()
qapi: make query-cpu-definitions depend on specific targets
qapi: make query-cpu-model-expansion depend on s390 or x86
qapi: make query-gic-capabilities depend on TARGET_ARM
target.json: add a note about query-cpu* not being s390x-specific
qapi: make s390 commands depend on TARGET_S390X
qapi: make rtc-reset-reinjection and SEV depend on TARGET_I386
qapi: New module target.json
build: Deal with all of QAPI's .o in qapi/Makefile.objs
build-sys: move qmp-introspect per target
qapi: Generate QAPIEvent stuff into separate files
qapi: Prepare for system modules other than 'builtin'
qapi: Clean up modular built-in code generation a bit
qapi: Fix up documentation for recent commit a95291007b
qapi: Belatedly document modular code generation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few targets don't emit RTC_CHANGE, we could restrict the event to
the tagets that do emit it.
Note: There is a lot more of events & commands that we could restrict
to capable targets, with the cost of some additional complexity, but
the benefit of added correctness and better introspection.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-19-armbru@redhat.com>
Move rtc-reset-reinjection and SEV in target.json and make them
conditional on TARGET_I386.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-10-armbru@redhat.com>
Latest systems and host kernels support mepoch, which is a
feature that was meant to be supported for z14 GA1 from the
get-go. Let's copy it to the z14 GA1 default CPU model.
Machines s390-ccw-virtio-3.1 and older will retain the old CPU
models and will not provide this bit nor the extended PTFF
functions in the default model.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Message-Id: <20190212011657.18324-2-walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As we now always have PCI support, let's add it to the "qemu" CPU model,
taking care of backwards compatibility.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190212112323.15904-1-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We tried to make pci support optional on s390x in the past;
unfortunately, we still require the s390 phb to be created
unconditionally due to backwards compatibility issues.
Instead of sinking more effort into this (including compat
handling for older machines etc.) for non-obvious gains, let's
just make CONFIG_PCI something that is always set on s390x.
Note that you can still fence off pci for the _guest_ if you
provide a cpu model without the zpci feature.
Message-Id: <20190211113255.3837-1-cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "simple" ICS class knows how to interract with KVM. Adapt sPAPR to use
it instead of the ICS KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023083585.1011724.2868047424353921455.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICS reset handler simply writes the ICS state to KVM. This
doesn't need the overkill parent_reset logic we have today. Also
we want to use the same ICS type for the KVM and non-KVM case with
pseries.
Call icp_set_kvm_state() from the "simple" ICS reset function.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082407.1011724.1983100830860273401.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The base ICP class knows how to interact with KVM. Adapt sPAPR to use it
instead of the ICP KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080638.1011724.792095453419098948.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we have changed the XICS and the XIVE interrupt backend to
have different size for their IRQ number space, we do not need to
align their source numbers anymore. Remove the offset adjustment and
wire the dual 'qirq' handler to the 'qirq' handler of the current
interrupt mode in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the 'dual' interrupt mode, the source numbers of both sPAPR
IRQ backends are aligned to share a common IRQ number space and to use
a similar mapping of the machine qemu_irq array which is indexed by
the source number.
The XICS IRQ number range initially being [ 0x1000 - 0x2000 ], this
requires to change the XICS ICSState offset to 0 and to provision for
an extra 4K of source numbers and qemu_irqs which will never be used
by the machine when running under the XICS interrupt mode. This is not
an optimal solution.
Change the init() method to allocate an IRQ number space of the
expected size for the XICS sPAPR IRQ backend. It breaks the interrupt
signaling when under the 'dual' mode because source numbers have
unexpected values but next patch will fix that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
buf_len is uint8_t which is not large enough to hold the result of:
nr_entries * sizeof(struct sPAPRDrconfCellV2) + sizeof(uint32_t);
for a nr_entries greater than 10.
This causes the allocated buffer 'int_buf' to be smaller than expected
and we eventually overwrite some of glibc's control structures (see
"chunk" in https://sourceware.org/glibc/wiki/MallocInternals)
The following error is seen while trying to free int_buf:
"free(): invalid next size (fast)"
Fixes: a324d6f166 "spapr: Support ibm,dynamic-memory-v2 property"
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20190213172926.21740-1-farosas@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Certain devices types, like memory/CPU, are now being handled using a
hotplug interface provided by a top-level MachineClass. Hotpluggable
host bridges are another such device where it makes sense to use a
machine-level hotplug handler. However, unlike those devices,
host-bridges have a parent bus (the main system bus), and devices with
a parent bus use a different mechanism for registering their hotplug
handlers: qbus_set_hotplug_handler(). This interface currently expects
a handler to be a subclass of DeviceClass, but this is not the case
for MachineClass, which derives directly from ObjectClass.
Internally, the interface only requires an ObjectClass, so expose that
in qbus_set_hotplug_handler().
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <154999589921.690774.3640149277362188566.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MSI is the default and LSI specific code is guarded by the
xive_source_irq_is_lsi() helper. The xive_source_irq_set()
helper is a nop for MSIs.
Simplify the code by turning xive_source_irq_set() into
xive_source_irq_set_lsi() and only call it for LSIs. The
call to xive_source_irq_set(false) in spapr_xive_irq_free()
is also a nop. Just drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <154999584656.690774.18352404495120358613.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This model brings out-of-the-box networking for all of Linux, MacOS 9 and OS X
without requiring the installation of additional drivers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190208172201.29001-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Split mode doesn't make sense on pseries, neither with XICS nor XIVE. But
passing kernel-irqchip=split silently behaves like kernel-irqchip=on.
Other architectures that support kernel-irqchip do terminate QEMU when
split mode is requested but not available though. Do the same with pseries
for consistency.
Similarly, passing kernel-irqchip=on,accel=tcg starts the machine with the
emulated interrupt controller, ie, behaves like kernel-irqchip=off. However,
when passing kernel-irqchip=on,accel=kvm, if we can't initialize the KVM
XICS for some reason, ie, xics_kvm_init() fails, then QEMU is terminated.
This is inconsistent. Terminate QEMU all the same when requesting the
in-kernel interrupt controller without KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <154964986747.291716.2679312373018476920.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to handle a race condition in the MacOS 9 CUDA driver, a
delay was introduced when raising the VIA SR interrupt inspired by
similar code in MacOnLinux.
During original testing of the MacOS 9 patches it was found that the
30us delay used in MacOnLinux did not work reliably within QEMU, and a
value of 300us was required to function correctly.
Recent experiments have shown two things: firstly when booting Linux,
MacOS 9 and MacOS X the fast path which bypasses the delay is never
triggered once the OS kernel is loaded making it effectively
useless. Rather than leave this code in place where a guest could
potentially enable it by accident and break itself, we might as well
just remove it.
Secondly the previous reliability issues are no longer present, and
this value can be reduced down to 20us with no apparent ill
effects. This has the benefit of considerably improving the
responsiveness of the ADB keyboard and mouse within the guest.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that IRQ allocation has been split in two (first allocate IRQ numbers,
then claim them), if the claiming fails, we must release the IRQs.
Fixes: 4fe75a8ccd "spapr: split the IRQ allocation sequence"
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All this code is used with both the XICS and XIVE interrupt controllers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In 47973a2dbf we split the last generic chipset out of the PC
board, but forgot to remove the include of "hw/i386/pc.h".
Since it is now unused, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 91c1e9fcbd where we added dual-CPU support to
the ARMSSE, we set up the wiring of the expansion IRQs via nested
loops: the outer loop on 'i' loops for each CPU, and the inner loop
on 'j' loops for each interrupt. Fix a typo which meant we were
wiring every expansion IRQ line to external IRQ 0 on CPU 0 and
to external IRQ 1 on CPU 1.
Fixes: 91c1e9fcbd ("hw/arm/armsse: Support dual-CPU configuration")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The code for handling the NVIC SHPR1 register intends to permit
byte and halfword accesses (as the architecture requires). However
the 'case' line for it only lists the base address of the
register, so attempts to access bytes other than the first one
end up in the "bad write" default logic. This bug was added
accidentally when we split out the SHPR1 logic from SHPR2 and
SHPR3 to support v6M.
Fixes: 7c9140afd5 ("nvic: Handle ARMv6-M SCS reserved registers")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
---
The Zephyr RTOS happens to access SHPR1 byte at a time,
which is how I spotted this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcZZvnAAoJENSXKoln91plz6UH/iqtHfPhGEj6o4CGFIx/8Ru/
k7XU552LgTGvIA1aHt9+dHNYWW/JRl1CvmdeECeAN/yFkKSdDmruW6hLV78dV6Jy
8xnnYt8bQhMfMSCIlkGh+CxFF0BCRoPrtH64ZVgZ9AnN00E6hyFlTHAYJEk8ZlcM
ov05JYneKlZWYDcJnYaGX6T7s8ALcq2O6FDUS88J9AiN303yt+kmaEC2WEt+xju4
+xPPBIIg8nqd3MlrQ/shpFcCOTN0OLQ4V5mQYLvbL3HGTzeZ8eYBRdqQ2DXpW8M8
OOFGhJrmfBYEC/me0T7suZnzLLNGGYz2jQWLlHy32COIAJv6GcUylGd9TDbGGP8=
=Py0Z
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amarkovic/tags/mips-queue-feb-14-2019' into staging
MIPS queue for February 14th, 2019
# gpg: Signature made Thu 14 Feb 2019 16:48:39 GMT
# gpg: using RSA key D4972A8967F75A65
# gpg: Good signature from "Aleksandar Markovic <amarkovic@wavecomp.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8526 FBF1 5DA3 811F 4A01 DD75 D497 2A89 67F7 5A65
* remotes/amarkovic/tags/mips-queue-feb-14-2019:
tests/tcg: target/mips: Add tests for MSA logic instructions
tests/tcg: target/mips: Add wrappers for MSA logic instructions
tests/tcg: target/mips: Add tests for MSA interleave instructions
tests/tcg: target/mips: Add wrappers for MSA interleave instructions
tests/tcg: target/mips: Add tests for MSA bit counting instructions
tests/tcg: target/mips: Add wrappers for MSA bit counting instructions
tests/tcg: target/mips: Add a header with test utilities
tests/tcg: target/mips: Add a header with test inputs
tests/tcg: target/mips: Remove an unnecessary file
target/mips: introduce MTTCG-enabled builds
hw/mips_cpc: kick a VP when putting it into Run statewq
target/mips: hold BQL in mips_vpe_wake()
hw/mips_int: hold BQL for all interrupt requests
target/mips: reimplement SC instruction emulation and use cmpxchg
target/mips: compare virtual addresses in LL/SC sequence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While testing mttcg VP0 could get stuck in a loop waiting for other
VPs to come up (which never actually happens). To fix this, kick VPs
while they are being powered up by Cluster Power Controller in an
async task which is triggered once the host thread is being spawned.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Make sure BQL is held for all interrupt requests.
For MTTCG-enabled configurations, handling soft and hard interrupts
between vCPUs must be properly locked. By acquiring BQL, make sure
all paths triggering an IRQ are synchronized.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
-----BEGIN PGP SIGNATURE-----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=I5Qi
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chardev-pull-request' into staging
Chardev fixes
# gpg: Signature made Wed 13 Feb 2019 16:18:36 GMT
# gpg: using RSA key DAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chardev-pull-request: (25 commits)
char-pty: remove write_lock usage
char-pty: remove the check for connection on write
chardev: add a note about frontend sources and context switch
terminal3270: do not use backend timer sources
char: update the mux handlers in class callback
chardev/wctablet: Fix a typo
char: allow specifying a GMainContext at opening time
chardev: ensure termios is fully initialized
tests: expand coverage of socket chardev test
chardev: fix race with client connections in tcp_chr_wait_connected
chardev: disallow TLS/telnet/websocket with tcp_chr_wait_connected
chardev: honour the reconnect setting in tcp_chr_wait_connected
chardev: use a state machine for socket connection state
chardev: split up qmp_chardev_open_socket connection code
chardev: split tcp_chr_wait_connected into two methods
chardev: remove unused 'sioc' variable & cleanup paths
chardev: ensure qemu_chr_parse_compat reports missing driver error
chardev: remove many local variables in qemu_chr_parse_socket
chardev: forbid 'wait' option with client sockets
chardev: forbid 'reconnect' option with server sockets
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch set contains a handful of patches I've collected over the
last few weeks. There's nothing really fundamental, but I thought it
would be good to send these out now as there are some other patch sets
on the mailing list that are getting ready to go.
As far as the actual patches, there's:
* A set that cleans up our FS dirty-mode handling.
* Support for writing MISA.
* The removal of Michael as a maintainer.
* A fix to {m,s}counteren handling.
* A fix to make sure the kernel's start address is computed correctly on
32-bit targets.
This makes my "RISC-V Patches for 3.2, Part 3" pull request defunct, as
it contains the same patches but based on a newer master. As usual,
I've tested this using a Fedora boot on the latest Linux. This patch
set does not include Bastian's decodetree patches because there were
some merge conflicts and while I've cleaned them up I want to get a
round of review first.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEAM520YNJYN/OiG3470yhUCzLq0EFAlxkOc4THHBhbG1lckBk
YWJiZWx0LmNvbQAKCRDvTKFQLMurQZwhEACZtcbDNgXFnV3lpN4mQ7np3EYUsiFv
lEGip+/iBlTp2IWA7pXxw4wTV584/0uK9Y7errHoIB16JSNPpK1si5RTiUVWe8yo
QfYI8/c8zrXHkupMr+T4WZEu1WP6dgl5ZFO8tE/3xF2G/uMJwtTEXZ29OxUAa9tr
8Xsk8Sbs8LBa3YYY+8fGCEa/duG9Bb2DNIgyC6U0Iz3liKCFYWHnjODvs8c+Hpft
0A+VJ3zhAKLAoPymrKmbJc6mYdNNljHMaVg7uDnoxDpLo2Hb0pNuCd0AwmnJVKr5
eI6HV7XzEAxXOY96z4YWtS+/Mqxlo1wUhlkDO0acDoxFSz7XDSMecxowwdNWuwzM
WlHPUAd7VQ8j8oSO4dnRAZnC7Trn172q1tpg+xjWxm8FZuyBzTrOjwoVUW9hoXTt
62GQKtDhWt++Uzq1q0hdaVAckz3c+yBGBCXlQG9wAJVyFSdowQTeYkcW5PU3f6nv
CkZ/nY4hQgtwgxB+PAIobcgkt07bhMnWAxQYRVJaKBAX5Ea7dudQHw9eSL6eI40X
GXhzt5jsj9HRhzSqaKqcIixO1ouIsvAoCD1QNLrCeXNEoa7xMOo7FCLWT3lpj49G
TWmUjrNA/qMB25HMVOaF7lH7mwRShg3wx5oqDQII35TcGx4u+psi9oApPyRUHOFx
syEZaIPiIn+nCw==
=Q/8G
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.0-sf1' into staging
RISC-V Patches for the 4.0 Soft Freeze, Part 1
This patch set contains a handful of patches I've collected over the
last few weeks. There's nothing really fundamental, but I thought it
would be good to send these out now as there are some other patch sets
on the mailing list that are getting ready to go.
As far as the actual patches, there's:
* A set that cleans up our FS dirty-mode handling.
* Support for writing MISA.
* The removal of Michael as a maintainer.
* A fix to {m,s}counteren handling.
* A fix to make sure the kernel's start address is computed correctly on
32-bit targets.
This makes my "RISC-V Patches for 3.2, Part 3" pull request defunct, as
it contains the same patches but based on a newer master. As usual,
I've tested this using a Fedora boot on the latest Linux. This patch
set does not include Bastian's decodetree patches because there were
some merge conflicts and while I've cleaned them up I want to get a
round of review first.
# gpg: Signature made Wed 13 Feb 2019 15:37:50 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.0-sf1:
riscv: Ensure the kernel start address is correctly cast
target/riscv: fix counter-enable checks in ctr()
MAINTAINERS: Remove Michael Clark as a RISC-V Maintainer
RISC-V: Add misa runtime write support
RISC-V: Add misa.MAFD checks to translate
RISC-V: Add misa to DisasContext
RISC-V: Add priv_ver to DisasContext
RISC-V: Use riscv prefix consistently on cpu helpers
RISC-V: Implement mstatus.TSR/TW/TVM
RISC-V: Mark mstatus.fs dirty
RISC-V: Split out mstatus_fs from tb_flags
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sun4uv_init() function expects vga_interface_type to be either
VGA_STD or VGA_NONE and sets up a stdvga device or no vga card
accordingly.
However, the code in vl.c prefers the Cirrus VGA card to stdvga if
it is available and the user and the machine did not specify anything
else.
So far this has not been a problem, since the Cirrus VGA was not linked
into the sparc64 target. But with the upcoming Kconfig build system,
all theoretically possible PCI cards will be enabled by default, so the
Cirrus VGA card might become available on the sparc64 target, too. vl.c
then picks the wrong card, causing sun4uv_init() to abort.
Thus let's make it explicit that we always want stdvga for sparc64 and
so set default_display = "std" for these machines.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <1550041639-10232-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20181016112232.23241-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
terminal3270 uses the front-end side of the chardev. It shouldn't
create sources from backend side context (with backend
functions).
send_timing_mark_cb calls qemu_chr_fe_write_all() which should be
thread safe.
This partially reverts changes from commit
2c716ba150.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190206174328.9736-4-marcandre.lureau@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
This will be needed by vhost-user-test, when each test switches to
its own GMainLoop and GMainContext. Otherwise, for a reconnecting
socket the initial connection will happen on the default GMainContext,
and no one will be listening on it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190202110834.24880-1-pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Commit caa1ee43 "vhost-user-blk: add discard/write zeroes features
support" added fields to struct virtio_blk_config. This changes
the size of the config space and breaks migration from QEMU 3.1
and older:
qemu-system-ppc64: get_pci_config_device: Bad config data: i=0x10 read: 41 device: 1 cmask: ff wmask: 80 w1cmask:0
qemu-system-ppc64: Failed to load PCIDevice:config
qemu-system-ppc64: Failed to load virtio-blk:virtio
qemu-system-ppc64: error while loading state for instance 0x0 of device 'pci@800000020000000:01.0/virtio-blk'
qemu-system-ppc64: load of migration failed: Invalid argument
Since virtio-blk doesn't support the "discard" and "write zeroes"
features, it shouldn't even expose the associated fields in the
config space actually. Just include all fields up to num_queues to
match QEMU 3.1 and older.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1550022537-27565-1-git-send-email-changpeng.liu@intel.com
Message-Id: <1550022537-27565-1-git-send-email-changpeng.liu@intel.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
HP-UX 10.20 uses busmaster writes to the CPU EIR to signal
interrupts from the SCSI constroller. (Similar to what is known
as MSI on x86)
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190211192039.5457-1-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In several part we still using req->dev or VIRTIO_DEVICE(req->dev)
when we have already defined s and vdev pointers:
VirtIOBlock *s = req->dev;
VirtIODevice *vdev = VIRTIO_DEVICE(s);
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 20190208142347.214815-1-sgarzare@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cast the kernel start address to the target bit length.
This ensures that we calculate the initrd offset to a valid address for
the architecture.
Steps to reproduce the original problem (reported by Alex):
Build U-Boot for the virt machine for riscv32. Then run it with
$ qemu-system-riscv32 -M virt -kernel u-boot -nographic -initrd <a file>
You can find the initrd address with
U-Boot# fdt addr $fdtcontroladdr
U-Boot# fdt ls /chosen
Then take a peek at that address:
U-Boot# md.b <addr>
and you will see that there is nothing there without this patch. The
reason is that the binary was loaded to a negative address.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Reported-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This is to enable OpenBIOS to claim the initrd memory as in-use before attempting
to boot the kernel.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The sun4u/sun4v machine currently always creates a VGA device, even if
the user started QEMU with "-nodefaults" or "-vga none". That's likely
not what the users expect in this case, so add a check whether the VGA
adapter has really been requested.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
When building with TSC_VERBOSE not defined, we get:
CC arm-softmmu/hw/input/tsc210x.o
hw/input/tsc210x.c: In function ‘tsc2102_data_register_write’:
hw/input/tsc210x.c:554:5: error: label at end of compound statement
default:
^~~~~~~
hw/input/tsc210x.c: In function ‘tsc2102_control_register_write’:
hw/input/tsc210x.c:638:5: error: label at end of compound statement
bad_reg:
^~~~~~~
hw/input/tsc210x.c: In function ‘tsc2102_audio_register_write’:
hw/input/tsc210x.c:766:5: error: label at end of compound statement
default:
^~~~~~~
make[1]: *** [rules.mak:69: hw/input/tsc210x.o] Error 1
Fix this by replacing the culprit fprintf(stderr) calls by a more
recent API: qemu_log_mask(LOG_GUEST_ERROR). Other fprintf() calls
are left untouched.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190204204517.23698-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The device can not be instantiated by the user and QEMU currently
aborts when you try to use it:
$ x86_64-softmmu/qemu-system-x86_64 -device cpu-cluster
qemu-system-x86_64: hw/cpu/cluster.c:73: cpu_cluster_realize:
Assertion `cbdata.cpu_count > 0' failed.
Aborted (core dumped)
Since this is an internal device only, mark it with user_creatable = false.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1549371525-29899-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In 47973a2dbf we split the last generic chipset out of the PC
board, but forgot to remove the include of "hw/i386/pc.h".
Since it is now unused, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190204210433.26088-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In 47973a2dbf we split the last generic chipset out of the PC
board, but forgot to remove the include of "hw/i386/pc.h".
Since it is now unused, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190204210433.26088-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
* Implement Armv8.5-BTI extension for system emulation mode
* Implement the PR_PAC_RESET_KEYS prctl() for linux-user mode's Armv8.3-PAuth support
* Support TBI (top-byte-ignore) properly for linux-user mode
* gdbstub: allow killing QEMU via vKill command
* hw/arm/boot: Support DTB autoload for firmware-only boots
* target/arm: Make FPSCR/FPCR trapped-exception bits RAZ/WI
-----BEGIN PGP SIGNATURE-----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=XEy2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190205' into staging
target-arm queue:
* Implement Armv8.5-BTI extension for system emulation mode
* Implement the PR_PAC_RESET_KEYS prctl() for linux-user mode's Armv8.3-PAuth support
* Support TBI (top-byte-ignore) properly for linux-user mode
* gdbstub: allow killing QEMU via vKill command
* hw/arm/boot: Support DTB autoload for firmware-only boots
* target/arm: Make FPSCR/FPCR trapped-exception bits RAZ/WI
# gpg: Signature made Tue 05 Feb 2019 17:04:22 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190205: (22 commits)
target/arm: Make FPSCR/FPCR trapped-exception bits RAZ/WI
hw/arm/boot: Support DTB autoload for firmware-only boots
hw/arm/boot: Clarify why arm_setup_firmware_boot() doesn't set env->boot_info
hw/arm/boot: Factor out "set up firmware boot" code
hw/arm/boot: Factor out "direct kernel boot" code into its own function
hw/arm/boot: Fix block comment style in arm_load_kernel()
gdbstub: allow killing QEMU via vKill command
target/arm: Enable TBI for user-only
target/arm: Compute TB_FLAGS for TBI for user-only
target/arm: Clean TBI for data operations in the translator
target/arm: Add TBFLAG_A64_TBID, split out gen_top_byte_ignore
tests/tcg/aarch64: Add pauth smoke test
linux-user: Implement PR_PAC_RESET_KEYS
target/arm: Enable BTI for -cpu max
target/arm: Set btype for indirect branches
target/arm: Reset btype for direct branches
target/arm: Default handling of BTYPE during translation
target/arm: Cache the GP bit for a page in MemTxAttrs
exec: Add target-specific tlb bits to MemTxAttrs
target/arm: Add BT and BTYPE to tb->flags
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The arm_boot_info struct has a skip_dtb_autoload flag: if this is
set to true by the board code then arm_load_kernel() will not
load the DTB itself, but will leave this for the board code to
do itself later. However, the check for this is done in a
code path which is only executed for the case where we load
a kernel image file. If we're taking the "boot via firmware"
code path then the flag isn't honoured and the DTB is never
loaded.
We didn't notice this because the only real user of "boot
via firmware" that cares about the DTB is the virt board
(for UEFI boot), and that always wants skip_dtb_autoload
anyway. But the SBSA reference board model we're planning to
add will want the flag to behave correctly.
Now we've refactored the arm_load_kernel() function, the
fix is simple: drop the early 'return' so we fall into
the same "load the DTB" code the boot-direct-kernel path uses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-6-peter.maydell@linaro.org
The code path for booting firmware doesn't set env->boot_info. At
first sight this looks odd, so add a comment saying why we don't.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-5-peter.maydell@linaro.org
Factor out the "boot via firmware" code path from arm_load_kernel()
into its own function.
This commit only moves code around; no semantic changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-4-peter.maydell@linaro.org
Factor out the "direct kernel boot" code path from arm_load_kernel()
into its own function; this function is getting long enough that
the code flow is a bit confusing.
This commit only moves code around; no semantic changes.
We leave the "load the dtb" code in arm_load_kernel() -- this
is currently only used by the "direct kernel boot" path, but
this is a bug which we will fix shortly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-3-peter.maydell@linaro.org
Fix the block comment style in arm_load_kernel() to QEMU's
current style preferences. This will allow us to do some
refactoring of this function without checkpatch complaining
about the code-motion patches.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-2-peter.maydell@linaro.org
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcWbMUAAoJECgfDbjSjVRp2acH+wa8abfyQIpVMji+cdvcw7Wo
yJjCoPxX0y+tm7FGp6YjyyQhSzjUYRS+71NL6xkZVxs8yh4ZCbb/xDRYmrVG2cb6
6tUcqp1zlMp+w+kVKS4m4WTb0Z1bIODOi99tNBXxYjWY9lXF/hjZbhRpt6vL/NaP
hqYtp+wlhyjxsY/GFn5XZLY7F6+QKq/lsMJD80FvbtHBh/ngqmgyoouNwYzg1faW
M3wD5A3IOXLzU+MGK6uCtKK0+t3xzvaVJL7zChimKkn+y+Pg9T+s04zQS739bJRg
dYYrVK3IOt2tvVxBZnnUm9eBIxxElAxRssmERPe2i0mBRSXYKomuVZrXJ6ROhjA=
=TxWc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, features
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Feb 2019 16:00:20 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
contrib/libvhost-user: cleanup casts
r2d: fix build on mingw
mmap-alloc: fix hugetlbfs misaligned length in ppc64
mmap-alloc: unfold qemu_ram_mmap()
i386, acpi: cleanup build_facs by removing second unused argument
fw_cfg: fix the life cycle and the name of "qemu_extra_params_fw"
acpi: Make TPM 2.0 with TIS available as MSFT0101
hw/virtio: Use CONFIG_VIRTIO_PCI switch instead of CONFIG_PCI
vhost-user-blk: add discard/write zeroes features support
contrib/vhost-user-blk: fix the compilation issue
pci/msi: export msi_is_masked()
intel_iommu: reset intr_enabled when system reset
intel_iommu: fix operator in vtd_switch_address_space
hw: virtio-pci: drop DO_UPCAST
include: update Linux headers to 4.21-rc1/5.0-rc1
scripts/update-linux-headers.sh: adjust for Linux 4.21-rc1 (or 5.0-rc1)
contrib/libvhost-user: switch to uint64_t
virtio: add checks for the size of the indirect table
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Comment near strncpy explains kernel_cmdline does
not need to be 0-terminated.
Accordingly mark it as QEMU_NONSTRING.
Without this, gcc warns:
'strncpy' specified bound 256 equals destination size
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The second argument of build_facs() is not used, just remove it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Commit 19bcc4bc32 ("fw_cfg: Make qemu_extra_params_fw locally",
2019-01-04) changed the storage duration of the "qemu_extra_params_fw"
array from static to automatic. This broke the interface contract on the
fw_cfg_add_file() function, which is documented as follows, in
"include/hw/nvram/fw_cfg.h":
> [...] The data referenced by the starting pointer is only linked, NOT
> copied, into the data structure of the fw_cfg device. [...]
As a result, when guest firmware fetches the "etc/boot-menu-wait" fw_cfg
file, it now sees garbage. Fix the regression by changing the storage
duration to allocated. (The call is reached at most once, on the realize
path of the board-specific fw_cfg sysbus device.)
While at it, clean up the name and the assignment of the object as well.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Fixes: 19bcc4bc32
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This patch makes the a TPM 2.0 with TIS interface available under the
HID 'MSF0101'. This is supported by Linux and also Windows now
recognizes the TPM 2.0 with TIS interface. Leave the TPM 1.2 as before.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
For downstream s390x builds, we'd like to be able to build QEMU with
CONFIG_VIRTIO_PCI disabled (since virtio-ccw is used here instead),
but still with CONFIG_PCI enabled. This currently fails since the
virtio-*-pci.o files are still included in the build, but virtio-pci.o
is missing. Use the right config switch CONFIG_VIRTIO_PCI to exclude
the virtio-*-pci.o files from the build.
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
