Introduce a new opcode for negative setcond.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the separate defines with TCG_TARGET_HAS_extr_i64_i32,
so that the two parts of backend-specific type changing cannot
be out of sync.
Reported-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: <20230822175127.1173698-1-richard.henderson@linaro.org>
tlb_addr is changed from target_ulong to uint64_t to match the type of
a CPUTLBEntry value, and the addressed is changed to vaddr.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-8-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In system mode, abi_ptr is primarily used for representing addresses
when accessing guest memory with cpu_[st|ld]*(). Widening it from
target_ulong to vaddr reduces the target dependence of these functions
and is step towards building accel/ once for system mode.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-7-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Changes the address type of the guest memory read/write functions from
target_ulong to abi_ptr. (abi_ptr is currently typedef'd to target_ulong
but that will change in a following commit.) This will reduce the
coupling between accel/ and target/.
Note: Function pointers that point to cpu_[st|ld]*() in target/riscv and
target/rx are also updated in this commit.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-6-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Changes the signature of the target-defined functions for
inserting/removing hvf hw breakpoints. The address and length arguments
are now of vaddr type, which both matches the type used internally in
accel/hvf/hvf-all.c and makes the api target-agnostic.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-5-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Changes the signature of the target-defined functions for
inserting/removing kvm hw breakpoints. The address and length arguments
are now of vaddr type, which both matches the type used internally in
accel/kvm/kvm-all.c and makes the api target-agnostic.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-4-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Widens the pc and saved_insn fields of hvf_sw_breakpoint from
target_ulong to vaddr. Other hvf_* functions accessing hvf_sw_breakpoint
are also widened to match.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-3-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Widens the pc and saved_insn fields of kvm_sw_breakpoint from
target_ulong to vaddr. The pc argument of kvm_find_sw_breakpoint is also
widened to match.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-2-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Using "-device virtio-gpu,blob=true" currently does not work on big
endian hosts (like s390x). The guest kernel prints an error message
like:
[drm:virtio_gpu_dequeue_ctrl_func [virtio_gpu]] *ERROR* response 0x1200 (command 0x10c)
and the display stays black. When running QEMU with "-d guest_errors",
it shows an error message like this:
virtio_gpu_create_mapping_iov: nr_entries is too big (83886080 > 16384)
which indicates that this value has not been properly byte-swapped.
And indeed, the virtio_gpu_create_blob_bswap() function (that should
swap the fields in the related structure) fails to swap some of the
entries. After correctly swapping all missing values here, too, the
virtio-gpu device is now also working with blob=true on s390x hosts.
Fixes: e0933d91b1 ("virtio-gpu: Add virtio_gpu_resource_create_blob")
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2230469
Message-Id: <20230815122007.928049-1-thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
kvm_arch_get_default_type() returns the default KVM type. This hook is
particularly useful to derive a KVM type that is valid for "none"
machine model, which is used by libvirt to probe the availability of
KVM.
For MIPS, the existing mips_kvm_type() is reused. This function ensures
the availability of VZ which is mandatory to use KVM on the current
QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-2-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added doc comment for new function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Implement nRF51 DETECT signal in the GPIO peripheral.
The reference manual makes mention of a per-pin DETECT signal, but these
are not exposed to the user. See https://devzone.nordicsemi.com/f/nordic-q-a/39858/gpio-per-pin-detect-signal-available
for more information. Currently, I don't see a reason to model these.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-2-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than using a zero tuple to end the table, use a macro
to apply ARRAY_SIZE and pass that on to the convert functions.
This fixes two bugs in which the conversion functions required
that both the target and host masks be non-zero in order to
continue, rather than require both target and host masks be
zero in order to terminate.
This affected mmap_flags_tbl when the host does not support
all of the flags we wish to convert (e.g. MAP_UNINITIALIZED).
Mapping these flags to zero is good enough, and matches how
the kernel ignores bits that are unknown.
Fixes: 4b840f96 ("linux-user: Populate more bits in mmap_flags_tbl")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In order for our emulation of MAP_FIXED_NOREPLACE to succeed within
linux-user target_mmap, we require a non-zero value. This does not
require host kernel support, merely the bit being defined.
MAP_FIXED_NOREPLACE was added with glibc 2.28. From repology.org:
Fedora 36: 2.35
CentOS 8 (RHEL-8): 2.28
Debian 11: 2.31
OpenSUSE Leap 15.4: 2.31
Ubuntu LTS 20.04: 2.31
Reported-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230808164418.69989-1-richard.henderson@linaro.org>
We will want to be able to search the set of mappings.
For this patch, the two users iterate the tree in order.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Hi,
Here is a collection of ui, dump and chardev fixes that are worth for 8.1.
thanks
-----BEGIN PGP SIGNATURE-----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=ANQg
-----END PGP SIGNATURE-----
Merge tag 'fixes-pull-request' of https://gitlab.com/marcandre.lureau/qemu into staging
Fixes for 8.1
Hi,
Here is a collection of ui, dump and chardev fixes that are worth for 8.1.
thanks
# -----BEGIN PGP SIGNATURE-----
#
# iQJQBAABCAA6FiEEh6m9kz+HxgbSdvYt2ujhCXWWnOUFAmTRWDscHG1hcmNhbmRy
# ZS5sdXJlYXVAcmVkaGF0LmNvbQAKCRDa6OEJdZac5eUrD/9BvqJ87XSKchV01jji
# PmA+yFyI0JSG68oYbNPYJXxkLWdRCKp6GGcT8h1yiVtGH/SVey9spxDqbV+sK0uW
# FmqIcmSBbjI4A6+Mne07Iyd0QtgL9H6YNenRXDFLIXLh84HP47Dg9vfgx4AsRY7O
# efcCdi43/PoJOelVfn9wIkP/8DU4pZV6IsdtdUxZ3rtu/zwjW61rLzuxtLcAoCIE
# rAYiTp699NH5fKBbMzm3puK4hpaPLj4GuGPrSaWVSCcgARqi7LWpgZC5i+a6FUfS
# eWzK8WkdvHIPaUPRNl70LTWPKVxJ4PdSxFlIKgiH0bnpXHBvJnO2y1v4jaiGI0y2
# WSHKJWY513zTF4B+pMdQLjNiLotkiqtAXHw5rrjPTuVHxi1N5w6Z/BvWOSAvs8V6
# ijYmjksNoqwfpbPRTyu8psLcmj3fo2UIjQ739PgLN2lfC8d+nzdx4PIIq/ybQdZZ
# 7QBJGhxP33Ou8c3ok43Jz3go6w0WOKM0ucG1K1iTVxQ27leMKTO5Zsm2TShG2pMG
# CY6d/dumID8+G7sho8TmtTDjC5ZBkY5e27etkS+P4p+Buc60lqDrL+u6UadxWNZ1
# 3ifsQ1PhVTRuhZUJNMcX1Qo3PuEfAOH1ZuCbvXpubHwcUr4o/ZqlVrMaJtYB3ueo
# 7SX8YistmktaEeN+Y50qoiEVgg==
# =ANQg
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 07 Aug 2023 01:46:51 PM PDT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
* tag 'fixes-pull-request' of https://gitlab.com/marcandre.lureau/qemu:
ui/gtk: set scanout mode in gd_egl/gd_gl_area_scanout_texture
hw/i386/vmmouse:add relative packet flag for button status
dump: kdump-zlib data pages not dumped with pvtime/aarch64
virtio-gpu: reset gfx resources in main thread
virtio-gpu: free BHs, by implementing unrealize
chardev: report the handshake error
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Calling OpenGL from different threads can have bad consequences if not
carefully reviewed. It's not generally supported. In my case, I was
debugging a crash in glDeleteTextures from OPENGL32.DLL, where I asked
qemu for gl=es, and thus ANGLE implementation was expected. libepoxy did
resolution of the global pointer for glGenTexture to the GLES version
from the main thread. But it resolved glDeleteTextures to the GL
version, because it was done from a different thread without correct
context. Oops.
Let's stick to the main thread for GL calls by using a BH.
Note: I didn't use atomics for reset_finished check, assuming the BQL
will provide enough of sync, but I might be wrong.
Acked-by: Dongwon Kim <dongwon.kim@intel.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230726173929.690601-3-marcandre.lureau@redhat.com>
OpenRISC (or1k) has long long alignment to 4 bytes, but currently not
defined in abitypes.h. This lead to incorrect packing of /epoll_event/
structure and eventually infinite loop while waiting for file
descriptor[s] event[s].
Fixed also CRIS alignments (1 byte for all types).
Signed-off-by: Luca Bonissi <qemu@bonslack.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1770
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The first bitfield here is supposed to be used as a 64-bit equivalent
to the "uint64_t msi_addr" in the union. To make this work correctly
on big endian hosts, too, the __addr_hi field has to be part of the
bitfield, and the the bitfield members must be declared with "uint64_t"
instead of "uint32_t" - otherwise the values are placed in the wrong
bytes on big endian hosts.
Same applies to the 32-bit "msi_data" field: __resved1 must be part
of the bitfield, and the members must be declared with "uint32_t"
instead of "uint16_t".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-7-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The code already tries to do some endianness handling here, but
currently fails badly:
- While it already swaps the data when logging errors / tracing, it fails
to byteswap the value before e.g. accessing entry->irte.present
- entry->irte.source_id is swapped with le32_to_cpu(), though this is
a 16-bit value
- The whole union is apparently supposed to be swapped via the 64-bit
data[2] array, but the struct is a mixture between 32 bit values
(the first 8 bytes) and 64 bit values (the second 8 bytes), so this
cannot work as expected.
Fix it by converting the struct to two proper 64-bit bitfields, and
by swapping the values only once for everybody right after reading
the data from memory.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-3-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The QEMU CI fails in virtio-scmi test occasionally. As reported by
Thomas Huth, this happens most likely when the system is loaded and it
fails with the following error:
qemu-system-aarch64: ../../devel/qemu/hw/pci/msix.c:659:
msix_unset_vector_notifiers: Assertion `dev->msix_vector_use_notifier && dev->msix_vector_release_notifier' failed.
../../devel/qemu/tests/qtest/libqtest.c:200: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
As discovered by Fabiano Rosas, the cause is a duplicate invocation of
msix_unset_vector_notifiers via duplicate vu_scmi_stop calls:
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_disconnect
...
qemu_chr_write_buffer
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_set_status
...
qemu_cleanup
While vu_scmi_stop calls are protected by vhost_dev_is_started()
check, it's apparently not enough. vhost-user-blk and vhost-user-gpio
use an extra protection, see f5b22d06fb (vhost: recheck dev state in
the vhost_migration_log routine) for the motivation. Let's use the
same in vhost-user-scmi, which fixes the failure above.
Fixes: a5dab090e1 ("hw/virtio: Add boilerplate for vhost-user-scmi device")
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Message-Id: <20230720101037.2161450-1-mzamazal@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230730180329.851576-1-sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The TLS handshake make take some time to complete, during which time an
I/O watch might be registered with the main loop. If the owner of the
I/O channel invokes qio_channel_close() while the handshake is waiting
to continue the I/O watch must be removed. Failing to remove it will
later trigger the completion callback which the owner is not expecting
to receive. In the case of the VNC server, this results in a SEGV as
vnc_disconnect_start() tries to shutdown a client connection that is
already gone / NULL.
CVE-2023-3354
Reported-by: jiangyegen <jiangyegen@huawei.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Coverity points out (CID 1513106, 1513107) that MemoryListener is a
192 byte struct which we are passing around by value. Switch to
passing a const pointer into xen_register_ioreq() and then to
xen_do_ioreq_register(). We can also make the file-scope
MemoryListener variables const, since nothing changes them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230718101057.1110979-1-peter.maydell@linaro.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Extend query-migrate to provide throttle time and estimated
ring full time with dirty-limit capability enabled, through which
we can observe if dirty limit take effect during live migration.
Signed-off-by: Hyman Huang(黄勇) <yong.huang@smartx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-ID: <168733225273.5845.15871826788879741674-8@git.sr.ht>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Deciphering the hard-coded list of integer return values from
nbd_start_negotiate() will only get more confusing when adding support
for 64-bit extended headers. Better is to name things in an enum.
Although the function in question is private to client.c, putting the
enum in a public header and including an enum-to-string conversion
will allow its use in more places in upcoming patches.
The enum is intentionally laid out so that operators like <= can be
used to group multiple modes with similar characteristics, and where
the least powerful mode has value 0, even though this patch does not
exploit that. No semantic change intended.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20230608135653.2918540-9-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Externally, libnbd exposed the 64-bit opaque marker for each client
NBD packet as the "cookie", because it was less confusing when
contrasted with 'struct nbd_handle *' holding all libnbd state. It
also avoids confusion between the noun 'handle' as a way to identify a
packet and the verb 'handle' for reacting to things like signals.
Upstream NBD changed their spec to favor the name "cookie" based on
libnbd's recommendations[1], so we can do likewise.
[1] https://github.com/NetworkBlockDevice/nbd/commit/ca4392eb2b
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20230608135653.2918540-6-eblake@redhat.com>
[eblake: typo fix]
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Upstream NBD now documents[1] an extension that supports 64-bit effect
lengths in requests. As part of that extension, the size of the reply
headers will change in order to permit a 64-bit length in the reply
for symmetry[2]. Additionally, where the reply header is currently 16
bytes for simple reply, and 20 bytes for structured reply; with the
extension enabled, there will only be one extended reply header, of 32
bytes, with both structured and extended modes sending identical
payloads for chunked replies.
Since we are already wired up to use iovecs, it is easiest to allow
for this change in header size by splitting each structured reply
across multiple iovecs, one for the header (which will become wider in
a future patch according to client negotiation), and the other(s) for
the chunk payload, and removing the header from the payload struct
definitions. Rename the affected functions with s/structured/chunk/
to make it obvious that the code will be reused in extended mode.
Interestingly, the client side code never utilized the packed types,
so only the server code needs to be updated.
[1] https://github.com/NetworkBlockDevice/nbd/blob/extension-ext-header/doc/proto.md
as of NBD commit e6f3b94a934
[2] Note that on the surface, this is because some future server might
permit a 4G+ NBD_CMD_READ and need to reply with that much data in one
transaction. But even though the extended reply length is widened to
64 bits, for now the NBD spec is clear that servers will not reply
with more than a maximum payload bounded by the 32-bit
NBD_INFO_BLOCK_SIZE field; allowing a client and server to mutually
agree to transactions larger than 4G would require yet another
extension.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20230608135653.2918540-4-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
We had a mix of struct declarations followed by typedefs, and direct
struct definitions as part of a typedef. Pick a single style. Also
float forward declarations of opaque types to the top of the file,
rather than interspersed with function declarations, which will help a
future patch that wants to expose yet another opaque type that will be
referenced in NBDRequest. No semantic impact.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-ID: <20230608135653.2918540-3-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
[eblake: alter patch per mailing list feedback]
Signed-off-by: Eric Blake <eblake@redhat.com>
elf_hwcap_str() takes a bit number, but compares it for equality with
the HWCAP_S390_* masks. This causes /proc/cpuinfo to display incorrect
hwcaps.
Fix by introducing the HWCAP_S390_NR_* constants and using them in
elf_hwcap_str() instead of the HWCAP_S390_*. While at it, add the
missing nnpa, pcimio and sie hwcaps from the latest kernel.
Output before:
features : esan3 zarch stfle msa
Output after:
features : esan3 zarch stfle msa ldisp eimm etf3eh highgprs vx vxe
Fixes: e19807bee3 ("linux-user/elfload: Introduce elf_hwcap_str() on s390x")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230627151356.273259-1-iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Replace 'width' and 'height' in QemuDmaBuf with 'backing_widht'
and 'backing_height' as these commonly indicate the size of the
whole surface (e.g. guest's Xorg extended display). Then use
'width' and 'height' for sub region in there (e.g. guest's
scanouts).
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-ID: <20230713040444.32267-1-dongwon.kim@intel.com>
We adjust CONFIG_ATOMIC128 and CONFIG_CMPXCHG128 with
CONFIG_ATOMIC128_OPT in atomic128.h. It is difficult
to tell when those changes have been applied with the
ifdef we must use with CONFIG_CMPXCHG128. So instead
use HAVE_CMPXCHG128, which triggers -Werror-undef when
the proper header has not been included.
Improves tcg_gen_atomic_cmpxchg_i128 for s390x host, which
requires CONFIG_ATOMIC128_OPT. Without this we fall back
to EXCP_ATOMIC to single-step 128-bit atomics, which is
slow enough to cause some tests to time out.
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the 0/-1 result with true/false.
Invert the sense of the test of all callers.
Document the function.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230707204054.8792-25-richard.henderson@linaro.org>
Use the interval tree to locate an unused range in the VM.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230707204054.8792-17-richard.henderson@linaro.org>
Examine the interval tree to validate that a region
has no existing mappings.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230707204054.8792-10-richard.henderson@linaro.org>
Commit 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs") split
calls to scsi_req_new() and scsi_req_enqueue() in the virtio-scsi device.
No ill effects were observed until commit 8cc5583abe ("virtio-scsi: Send
"REPORTED LUNS CHANGED" sense data upon disk hotplug events") added a
unit attention that was easy to trigger with device hotplug and
hot-unplug.
Because the two calls were separated, all requests in the batch were
prepared calling scsi_req_new() to report a sense. The first one
submitted would report the right sense and reset it to NO_SENSE, while
the others reported CHECK_CONDITION with no sense data. This caused
SCSI errors in Linux.
To solve this issue, let's fetch the unit attention as early as possible
when we prepare the request, so that only the first request in the batch
will use the unit attention SCSIReqOps and the others will not report
CHECK CONDITION.
Fixes: 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs")
Fixes: 8cc5583abe ("virtio-scsi: Send "REPORTED LUNS CHANGED" sense data upon disk hotplug events")
Reported-by: Thomas Huth <thuth@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2176702
Co-developed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In many cases, blindly unplugging a virtio-mem device is problematic. We
can only safely remove a device once:
* The guest is not expecting to be able to read unplugged memory
(unplugged-inaccessible == on)
* The virtio-mem device does not have memory plugged (size == 0)
* The virtio-mem device does not have outstanding requests to the VM to
plug memory (requested-size == 0)
So let's add a callback to the virtio-mem device class to check for that.
We'll wire-up virtio-mem-pci next.
Message-ID: <20230711153445.514112-7-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's support unplug requests for virtio-md-pci devices that provide
a unplug_request_check() callback.
We'll wire that up for virtio-mem-pci next.
Message-ID: <20230711153445.514112-6-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's factor out (un)plug handling, to be reused from arm/virt code.
Provide stubs for the case that CONFIG_VIRTIO_MD is not selected because
neither virtio-mem nor virtio-pmem is enabled. While this cannot
currently happen for x86, it will be possible for arm/virt.
Message-ID: <20230711153445.514112-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's add a new abstract "virtio memory device" type, and use it as
parent class of virtio-mem-pci and virtio-pmem-pci.
Message-ID: <20230711153445.514112-2-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
