Repairing OFLAG_COPIED is usually safe because it is done after the
refcounts have been repaired. Therefore, it we did not find anyone else
referencing a data or L2 cluster, it makes no sense to not set
OFLAG_COPIED -- and the other direction (clearing OFLAG_COPIED) is
always safe, anyway, it may just induce leaks.
Furthermore, if OFLAG_COPIED is actually consistent with a wrong (leaky)
refcount, we will decrement the refcount with -r leaks, but OFLAG_COPIED
will then be wrong. qemu-img check should not produce images that are
more corrupted afterwards then they were before.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1527085
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509200059.31125-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This test case has been broken since 398e6ad014 (roughly half a
year). qemu-img amend requires its output image to be R/W, so it opens
it as such; the node is then turned into an read-only node automatically
which is now accompanied by a warning, however. This warning has not
been part of the reference output.
For one thing, this warning shows that we cannot keep the test case as
it is. We would need a format that has no create_opts but that does
have write support -- we do not have such a format, though.
Another thing is that qemu now actually checks whether an image format
supports amendment instead of whether it has create_opts (since the
former always implies the latter). So we can now use any format that
does not support amendment (even if it supports creation) and thus test
the same code path.
The reason nobody has noticed the breakage until now of course is the
fact that nobody runs the iotests for nbd+bochs. There actually was
never any reason to set the protocol to "nbd" but because that was
technically correct; functionally it made no difference. So that is the
first thing we are going to change: Make the protocol "file" instead so
that people might actually notice breakage here.
Secondly, now that bochs no longer works for the amend test case, we
have to change the format there anyway. Set let us just bend the truth
a bit, declare this test a raw test. In fact, that does not even
concern the bochs test cases, other than the output now reading 'bochs'
instead of 'IMGFMT'.
So with this test now being a raw test, we can rework the amend test
case to use raw instead.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180509210023.20283-8-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This adds test cases to 082 for qemu-img create/convert/amend "-o help"
on formats that do not support creation or amendment, respectively.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509210023.20283-7-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The only users of print_block_option_help() are qemu-img create and
qemu-img convert for the output image, so this function is always used
for image creation (it used to be used for amendment also, but that is
no longer the case).
So if image creation is not supported by either the format or the
protocol, there is no need to print any option description, because the
user cannot create an image like this anyway.
This also fixes an assertion failure:
$ qemu-img create -f bochs -o help
Supported options:
qemu-img: util/qemu-option.c:219:
qemu_opts_print_help: Assertion `list' failed.
[1] 24831 abort (core dumped) qemu-img create -f bochs -o help
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509210023.20283-6-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The more generic print_block_option_help() function is not really
suitable for qemu-img amend, for a couple of reasons:
(1) We do not need to append the protocol-level options, as amendment
happens only on one node and does not descend downwards to its
children.
(2) print_block_option_help() says those options are "supported". For
option amendment, we do not really know that. So this new function
explicitly says that those options are the creation options, and not
all of them may be supported.
(3) If the driver does not support option amendment, we should not print
anything (except for an error message that amendment is not
supported).
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1537956
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509210023.20283-5-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
It really is up to the caller to decide what this list of options means.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509210023.20283-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Looking at the qcow2 code that is riddled with error_report() calls,
this is really how it should have been from the start.
Along the way, turn the target_version/current_version comparisons at
the beginning of qcow2_downgrade() into assertions (the caller has to
make sure these conditions are met), and rephrase the error message on
using compat=1.1 to get refcount widths other than 16 bits.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180509210023.20283-3-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of checking whether a driver has a non-NULL create_opts we
should check whether it supports image amendment in the first place. If
it does, it must have create_opts.
On the other hand, if it does not have create_opts (so it does not
support amendment either), the error message "does not support any
options" is a bit useless. Stating clearly that the driver has no
amendment support whatsoever is probably better.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180509210023.20283-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch adds a test case to 153 which tries to overwrite an image
(using qemu-img create) while it is in use. Without the original user
explicitly sharing the necessary permissions (writing and truncation),
this should not be allowed.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180509215336.31304-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When creating a file, we should take the WRITE and RESIZE permissions.
We do not need either for the creation itself, but we do need them for
clearing and resizing it. So we can take the proper permissions by
replacing O_TRUNC with an explicit truncation to 0, and by taking the
appropriate file locks between those two steps.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180509215336.31304-3-mreitz@redhat.com
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
raw_apply_lock_bytes() and raw_check_lock_bytes() currently take a
BDRVRawState *, but they only use the lock_fd field. During image
creation, we do not have a BDRVRawState, but we do have an FD; so if we
want to reuse the functions there, we should modify them to receive only
the FD.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180509215336.31304-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Rather than limit total TB size to PAGE-32 bytes, end the TB when
near the end of a page. This should provide proper semantics of
SIGSEGV when executing near the end of a page.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-9-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Removed ctx->insn_pc in favour of ctx->base.pc_next.
Yes, it is annoying, but didn't want to waste its 4 bytes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-7-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The name gen_lookup_tb is at odds with tcg_gen_lookup_and_goto_tb.
For these cases, we do indeed want to exit back to the main loop.
Similarly, DISAS_UPDATE performs no actual update, whereas DISAS_EXIT
does what it says.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-6-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These are all indirect or out-of-page direct jumps.
We can indirectly chain to the next TB without going
back to the main loop.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-5-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We have exited the TB after using goto_tb; there is no
distinction from DISAS_NORETURN.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-3-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The raise_exception helper does not return. Do not generate
any code following that.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180512050250.12774-2-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
For the case where the end_transfer_func is also the caller of
ide_transfer_start, the mutual recursion can lead to unlimited
stack usage. Introduce a new version that can be used to change
tail recursion into a loop, and use it in trace_ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The ATAPI_INT_REASON_IO interrupt is raised when I/O starts, but in the
AHCI case ide_set_irq was actually called at the end of a mutual recursion.
Move it early, with the side effect that ide_transfer_start becomes a tail
call in ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
There is code checking s->end_transfer_func and it was not taught about
ide_transfer_cancel. We can just use ide_transfer_stop because
s->end_transfer_func is only ever called in the DRQ phase.
ide_transfer_cancel can then be removed, since it would just be
calling ide_transfer_halt.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-6-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The code can simply be moved to the sole caller that has notify == true.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-5-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Now that end_transfer_func is a tail call in ahci_start_transfer,
formalize the fact that the callback (of which ahci_start_transfer is
the sole implementation) takes care of the transfer too: rename it to
pio_transfer and, if it is present, call the end_transfer_func as soon
as it returns.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The PIO Setup FIS is written in the PIO:Entry state, which comes before
the ATA and ATAPI data transfer states. As a result, the PIO Setup FIS
interrupt is now raised before DMA ends for ATAPI commands, and tests have
to be adjusted.
This is also hinted by the description of the command header in the AHCI
specification, where the "A" bit is described as
When ‘1’, indicates that a PIO setup FIS shall be sent by the device
indicating a transfer for the ATAPI command.
and also by the description of the ACMD (ATAPI command region):
The ATAPI command must be either 12 or 16 bytes in length. The length
transmitted by the HBA is determined by the PIO setup FIS that is sent
by the device requesting the ATAPI command.
QEMU, which conflates the "generator" and the "receiver" of the FIS into
one device, always uses ATAPI_PACKET_SIZE, aka 12, for the length.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
It's not always 512, and it does wind up mattering for PIO tranfers,
because this means DRQ blocks are four times as big for ATAPI.
Replace an instance of 2048 with the correct define, too.
This patch by itself winds changing no behavior. fis->count is ignored
for CMD_PACKET, and sect_count only gets used in non-ATAPI cases.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The cdrom-test checks various block types - IDE, SCSI and
virtio, so it's a little bit hard to decide where this should
belong to in the MAINTAINERS file. But John volunteered to take
it, so let's put it into the IDE section for now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Commit 1454509726 recently broke the "-cdrom" parameter
on a couple of boards without us noticing it immediately. Thus let's
add a test which checks that "-cdrom" can at least be used to start
QEMU with certain machine types.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Acked-By: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
We already have the code for a boot file in tests/boot-sector.c,
so if the genisoimage program is available, we can easily create
a bootable CD ISO image that we can use for testing whether our
CD-ROM emulation and the BIOS CD-ROM boot works correctly.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Acked-By: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
We're going to use the s390x boot code for testing CD-ROM booting.
But the ISO loader of the s390-ccw bios is a little bit more picky
than the network loader and expects some magic bytes in the header
of the file (see linux_s390_magic in pc-bios/s390-ccw/bootmap.c), so
we've got to add them in our boot code here, too.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Acked-By: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-17-jsnow@redhat.com
[Fixed format specifiers. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-16-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Actually, this function looks pretty broken, but for now, let's finish
up what this series of commits came here to do.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-15-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-14-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-13-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-12-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Yes, comment, it ought to be 0x2C.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-10-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
They're now unused.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-9-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-8-jsnow@redhat.com
[Changed format specifier. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-6-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
A trace is added to let us watch unimplemented registers specifically,
as these are more likely to cause us trouble. Otherwise, the port read
traces now tell us what register is getting hit, which is nicer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Instead of tracking offsets, lets count the registers.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180531222835.16558-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The comment gives us a hint. *Maybe* we still have something to
process. Well, why not check?
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20180531004323.4611-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
