The num local variable is initialized to zero and has no writer.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently possible to hotplug a spapr_rng device but QEMU crashes
when we try to hot unplug:
ERROR:hw/core/qdev.c:295:qdev_unplug: assertion failed: (hotplug_ctrl)
Aborted
This happens because spapr_rng isn't plugged to any bus and sPAPR does
not provide hotplug support for it: qdev_get_hotplug_handler() hence
return NULL and we hit the assertion.
And anyway, it doesn't make much sense to unplug this device since hcalls
cannot be unregistered. Even the idea of hotplugging a RNG device instead
of declaring it on the QEMU command line looks weird.
This patch simply disables hotpluggability for the spapr-rng class.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This quirk is a workaround for the following hardware behaviour, on
which UEFI (specifically, the bootloader for Windows on Pi2) depends:
1. at boot with an SD card present, the interrupt status/enable
registers are initially zero
2. upon enabling it in the interrupt enable register, the card insert
bit in the interrupt status register is immediately set
3. after a subsequent controller reset, the card insert interrupt does
not fire, even if enabled in the interrupt enable register
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-3-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 723697551a.
This change was poorly tested on my part. It squelched card insertion
interrupts on reset, but that was not necessary because sdhci_reset()
clears all the registers (via the call to memset), so the subsequent
sdhci_insert_eject_cb() call never sees the card insert interrupt
enabled. However, not calling the insert_eject_cb results in prnsts
remaining 0, when it actually needs to be updated to indicate card
presence and R/O status.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent changes to sdhci broke SD on raspi. This change mirrors
the logic to create the SD card device at the board level.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456351128-5560-1-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pl061.c emulates two GPIO devices, ARM PL061 and TI Stellaris, which
share the same read/write functions (pl061_read and pl061_write).
However PL061 and Stellaris have different GPIO register definitions
and pl061_read()/pl061_write() doesn't check it. This patch enforces
checking on offset, preventing R/W into the reserved memory area.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455814580-17699-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When I reviewed Marc's fw_cfg DMA patches, I completely missed that the
way we set dma_enabled would break migration.
Gerd explained the right way (see reference below): dma_enabled should be
set to true by default, and only true->false transitions should be
possible:
- when the user requests that with
-global fw_cfg_mem.dma_enabled=off
or
-global fw_cfg_io.dma_enabled=off
as appropriate for the platform,
- when HW_COMPAT_2_4 dictates it,
- when board code initializes fw_cfg without requesting DMA support.
Cc: Marc Marí <markmb@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alexandre DERUMIER <aderumier@odiso.com>
Cc: qemu-stable@nongnu.org
Ref: http://thread.gmane.org/gmane.comp.emulators.qemu/390272/focus=391042
Ref: https://bugs.launchpad.net/qemu/+bug/1536487
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1455823860-22268-1-git-send-email-lersek@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzuKeAAoJECgfDbjSjVRpGzIH/1Tz6CoEq1rowiyVJ9B80oQU
gDI2YWnJDSwJllmAF0rmoPRBQR8op3ZETZiCAcADHoZ7kdBNWGbyQeaDrrEPH7Q/
rCDVt8Q3g80vs89aWKG0nQ16J2MW5TbkuiQw7pjQSdc9AbUdWpUqSiWnpZ+sPAql
6DuVpjQ4/rN2alucXoa1Sir8KDDV7kBuY8U6/KoY890qzh842dv2523qvuCza9yR
KX8Imj3oQAFjFSv5t1aOD3yYvWFd73EsReHPLGb1JtsVr/6wjs0sFUyA3JicBgnT
+kWoSObWikfDY69HnqTkJpkun6woMM3zW5h2SkUBf9QP3yqLfGIp9uSriNN84Ak=
=KXyh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pc
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 25 Feb 2016 11:16:46 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (21 commits)
q35: No need to check gigabyte_align
q35: Remove unused q35-acpi-dsdt.aml file
ich9: Remove enable_tco arguments from init functions
machine: Remove no_tco field
q35: Remove old machine versions
tests/vhost-user-bridge: fix build on 32 bit systems
vring: remove
virtio-scsi: do not use vring in dataplane
virtio-blk: do not use vring in dataplane
virtio-blk: fix "disabled data plane" mode
virtio: export vring_notify as virtio_should_notify
virtio: add AioContext-specific function for host notifiers
vring: make vring_enable_notification return void
block-migration: acquire AioContext as necessary
pci core: function pci_bus_init() cleanup
pci core: function pci_host_bus_register() cleanup
balloon: Use only 'pc-dimm' type dimm for ballooning
virtio-balloon: rewrite get_current_ram_size()
move get_current_ram_size to virtio-balloon.c
vhost-user: don't merge regions with different fds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gigabyte_align is always true on q35, so we don't need the
!gigabyte_align compat code anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The file was used only by older machine-types, and it is not
needed anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The enable_tco arguments are always true, so they are not needed
anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The field is always set to zero, so it is not necessary anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Migration with q35 was not possible before commit
04329029a8, because q35
unconditionally creates an ich9-ahci device, that was marked as
unmigratable. So all q35 machine classes before pc-q35-2.4 were
not migratable, so there's no point in keeping compatibility code
for them.
Remove all old pc-q35 machine classes and keep only pc-q35-2.4
and newer.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In disabled mode, virtio-blk dataplane seems to be enabled, but flow
actually goes through the normal virtio path. This patch simplifies a bit
the handling of disabled mode. In disabled mode, virtio_blk_handle_output
might be called even if s->dataplane is not NULL.
This is a bit tricky, because the current check for s->dataplane will
always trigger, causing a continuous stream of calls to
virtio_blk_data_plane_start. Unfortunately, these calls will not
do anything. To fix this, set the "started" flag even in disabled
mode, and skip virtio_blk_data_plane_start if the started flag is true.
The resulting changes also prepare the code for the next patch, were
virtio-blk dataplane will reuse the same virtio_blk_handle_output function
as "regular" virtio-blk.
Because struct VirtIOBlockDataPlane is opaque in virtio-blk.c, we have
to move s->dataplane->started inside struct VirtIOBlock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio dataplane needs to trigger the irq manually through the
guest notifier. Export virtio_should_notify so that it can be
used around event_notifier_set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This is used to register ioeventfd with a dataplane thread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Make the API more similar to the regular virtqueue API. This will
help when modifying the code to not use vring.c anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
remove unused param
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
remove unused param, and rename the other to a meaningful one.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
For now there are only two dimm's: pc-dimm and nvdimm. This patch is
actually needed to disable ballooning on nvdimm. But, to avoid future
bugs, instead of disallowing nvdimm, we allow only pc-dimm. So, if
someone adds new dimm which should be balloon-able, then this ability
should be explicitly specified here.
Why ballooning for nvdimm should be disabled for now:
NVDIMM for now is planned to use as a backing store for DAX filesystem
in the guest and thus this memory is excluded from guest memory
management and LRUs.
In this case libvirt running QEMU along with configured balloon almost
immediately inflates balloon and effectively kill the guest as
qemu counts nvdimm as part of the ram.
Counting dimm devices as part of the ram for ballooning was started from
commit 463756d03:
virtio-balloon: Fix balloon not working correctly when hotplug memory
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use pc_dimm_built_list() instead of qmp_pc_dimm_device_list()
Actually, Qapi is not related to this internal helper.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a crash in the target QEMU during migration.
Broken in commit c5f54f3.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[reworded commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This hypercall either initializes a page with zeros, or copies
another page.
According to LoPAPR, the i-cache of the page should also be
flushed if using H_ICACHE_INVALIDATE or H_ICACHE_SYNCHRONIZE,
and the d-cache should be synchronized to the RAM if the
H_ICACHE_SYNCHRONIZE flag is used. For this, two new functions
are introduced, kvmppc_dcbst_range() and kvmppc_icbi()_range, which
use the corresponding assembler instructions to flush the caches
if running with KVM on Power. If the code runs with TCG instead,
the code only uses tb_flush(), assuming that this will be
enough for synchronization.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
This just catches a couple of stragglers since I posted
the last clean-includes patchset last week.
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
get_current_ram_size() is used only in virtio-balloon.c
This patch moves it into virtio-balloon and make it static, to allow
some balloon-specific tuning.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost currently merges regions with contiguious virtual and physical
addresses. This breaks for vhost-user since that also needs fds to
match.
Add a vhost_ops entry to compare the fds for vhost-user only.
Cc: qemu-stable@nongnu.org
Cc: Victor Kaplansky <victork@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While guest/host ABI is documented in hw/acpi/bios-linker-loader.c,
the API was left undocumented.
This adds documentation for all API functions.
Additionally, input is validated to make sure all
pointers fall within range of provided files.
To allow this validation for checksum commands,
bios_linker_loader_add_checksum is changed to accept GArray * in place
of void *.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate timer once, at init time, instead of allocating/freeing
it all the time when starting/stopping the bus. Simplifies the
code, also fixes bugs (memory leak) due to missing checks whenever
the time is already allocated or not.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pid can be gotten from uhci device memory in uhci_handle_td(),
so the guest can trigger assert qemu if we get an invalid pid.
And the uhci spec 2.1.2 tells us The Host Controller sets Host
Controller Process Error bit to 1 when it detects a fatal error
and indicates that the Host Controller suffered a consistency
check failure while processing a Transfer Descriptor. An example
of a consistency check failure would be finding an illegal PID
field while processing the packet header portion of the TD.
When this error occurs, the Host Controller clears the Run/Stop
bit in the Command register to prevent further schedule execution.
We'd better to set UHCI_STS_HCPERR and kick an interrupt, check
the pid value at the first of uhci_handle_td function.
https://bugzilla.redhat.com/show_bug.cgi?id=1070027
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 1455867238-4720-1-git-send-email-arei.gonglei@huawei.com
[ applied minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets,
the USB Net device emulator uses a fixed length(4096) data buffer.
The incoming informationBufferOffset & Length combination could
overflow and cross that range. Check control message buffer
offsets and length to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-3-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator uses a fixed length(4096) data buffer. The incoming
packet length could exceed this limit. Add a check to avoid it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-2-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The TUSB6010 is a USB controller (as the name suggests). Move it from
hw/timer (where it was accidentally filed in 2013 when we moved
everything out of hw/) to hw/usb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455883404-10976-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator checks to see if the USB configuration descriptor
object is of RNDIS type(2). But it does not check if it is null,
which leads to a null dereference error. Add check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455188480-14688-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
qemu_fdt_setprop asserts in case of error hence no need to check
the returned value.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch allows the instantiation of the vfio-amd-xgbe device
from the QEMU command line (-device vfio-amd-xgbe,host="<device>").
The guest is exposed with a device tree node that combines the description
of both XGBE and PHY (representation supported from 4.2 onwards kernel):
Documentation/devicetree/bindings/net/amd-xgbe.txt.
There are 5 register regions, 6 interrupts including 4 optional
edge-sensitive per-channel interrupts.
Some property values are inherited from host device tree. Host device tree
must feature a combined XGBE/PHY representation (>= 4.2 host kernel).
2 clock nodes (dma and ptp) also are created. It is checked those clocks
are fixed on host side.
AMD XGBE node creation function has a dependency on vfio Linux header and
more generally node creation function for VFIO platform devices only make
sense with CONFIG_LINUX so let's protect this code with #ifdef CONFIG_LINUX.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Some passthrough'ed devices depend on clock nodes. Those need to be
generated in the guest device tree. This patch introduces some helpers
to build a clock node from information retrieved in the host device tree.
- copy_properties_from_host copies properties from a host device tree
node to a guest device tree node
- fdt_build_clock_node builds a guest clock node and checks the host
fellow clock is a fixed one.
fdt_build_clock_node will become static as soon as it gets used. A
dummy pre-declaration is needed for compilation of this patch.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch aligns the prototype with qemu_fdt_getprop. The caller
can choose whether the function self-asserts on error (passing
&error_fatal as Error ** argument, corresponding to the legacy behavior),
or behaves differently such as simply output a message.
In this later case the caller can use the new lenp parameter to interpret
the error if any.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch introduces the amd-xgbe VFIO platform device. It
allows the guest to do passthrough on a device exposing an
"amd,xgbe-seattle-v1a" compat string.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Use the macro PCI_CAP_LIST_NEXT instead of 1, so that the code would be
more self-explain.
This patch makes this change and also fixs one typo in comment.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For vfio device, we need to propagate the aer error to
Guest OS. we use the pcie_aer_msg() to send aer error
to guest.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
pcie_aer_init was used to emulate an aer capability for pcie device,
but for vfio device, the aer config space size is mutable and is not
always equal to PCI_ERR_SIZEOF(0x48). it depends on where the TLP Prefix
register required, so here we add a size argument.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
this function search the capability from the end, the last
size should 0x100 - pos, not 0xff - pos.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Device's Offset and size can reach PCIE_CONFIG_SPACE_SIZE,
fix the corresponding assert.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fixes all over the place.
New tests for pxe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWxedfAAoJECgfDbjSjVRp9ZoH/1zlxDy/iiJWXJI0jkcnbSof
/tFbchrj/hfz0/Wr0yeKJNdU1rMgiY0lYM1F5Pp4MQDHFoFM6i7LaLUYLQq92u+w
CpgTOMXwthOqn94yrBncKUN+OkB4vDW18sHd21rTh5n1oO9VjM4oQFSHpAtaDdnc
7dyryrlocBlgjARuOhW7A3KJAdPcKUer5JKdbWMDHw2wgwk1+7lx8ip7PBrFpMwW
PEEw2jo/lQw/rm/Kit+BV43NBy5pks2/jWmaXqH5jgCNixEmbY150dJLLW6lAqdh
xatnMxkQHpbEyf/Cy8M73v8vdOLjfQNdJ7GO0lc3CZw4bZBHbOcuzVEExvHewYw=
=vpiH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pxe
Fixes all over the place.
New tests for pxe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 18 Feb 2016 15:46:39 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
tests/vhost-user-bridge: add scattering of incoming packets
vhost-user interrupt management fixes
rules: filter out irrelevant files
change type of pci_bridge_initfn() to void
dec: convert to realize()
tests: add pxe e1000 and virtio-pci tests
msix: fix msix_vector_masked
virtio: optimize virtio_access_is_big_endian() for little-endian targets
vhost: simplify vhost_needs_vring_endian()
vhost: move virtio 1.0 check to cross-endian helper
virtio: move cross-endian helper to vhost
vhost-net: revert support of cross-endian vnet headers
virtio-net: use the backend cross-endian capabilities
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign pl031_init to pl031_info.instance_init and drop the
SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_rtc_init to exynos4210_rtc_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_pwm_init to exynos4210_pwm_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_mct_init to exynos4210_mct_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign DeviceClass::vmsd instead of using vmstate_register function
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* assign icp_pit_init to icp_pit_info.instance_init
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of these errors may be harmless (e.g. probing unimplemented
commands, or issuing CMD12 in the wrong state), and may also be quite
frequent. Spamming the standard error output isn't desirable in such
cases.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-4-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SD spec for ACMD41 says that a zero argument is an "inquiry"
ACMD41, which does not start initialisation and is used only for
retrieving the OCR. However, Tianocore EDK2 (UEFI) has a bug [1]: it
first sends an inquiry (zero) ACMD41. If that first request returns an
OCR value with the power up bit (0x80000000) set, it assumes the card
is ready and continues, leaving the card in the wrong state. (My
assumption is that this works on hardware, because no real card is
immediately powered up upon reset.)
This change models a delay of 0.5ms from the first ACMD41 to the power
being up. However, it also immediately sets the power on upon seeing a
non-zero (non-enquiry) ACMD41. This speeds up UEFI boot, it should
also account for guests that simply delay after card reset and then
issue an ACMD41 that they expect will succeed.
[1] https://github.com/tianocore/edk2/blob/master/EmbeddedPkg/Universal/MmcDxe/MmcIdentification.c#L279
(This is the loop starting with "We need to wait for the MMC or SD
card is ready")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CMD23 is optional for SD but required for MMC, and the UEFI bootloader
used for Windows on Raspberry Pi 2 issues it.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a reset function to the pxa2xx_mmci device; previously it had
no handling for system reset at all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-11-git-send-email-peter.maydell@linaro.org
Convert the pxa2xx_mmci device from manual save/load
functions to a VMStateDescription structure.
This is a migration compatibility break.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-10-git-send-email-peter.maydell@linaro.org
Now the PXA2xx MMCI device is QOMified itself, we can
update it to use the SDBus APIs to talk to the SD card.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455646193-13238-9-git-send-email-peter.maydell@linaro.org
Convert the pxa2xx_mmci device to be a sysbus device.
In this commit we only change the device itself, and leave
the interface to the SD card using the old non-SDBus APIs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-8-git-send-email-peter.maydell@linaro.org
Move the creation of the SD card device from the sdhci_sysbus
device itself into the boards that create these devices.
This allows us to remove the cannot_instantiate_with_device_add
notation because we no longer call drive_get_next in the device
model.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-7-git-send-email-peter.maydell@linaro.org
Update the SDHCI code to use the new SDBus APIs.
This commit introduces the new command line options required
to connect a disk to sdhci-pci:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-6-git-send-email-peter.maydell@linaro.org
Add a QOM bus for SD cards to plug in to.
Note that since sd_enable() is used only by one board and there
only as part of a broken implementation, we do not provide it in
the SDBus API (but instead add a warning comment about the old
function). Whoever converts OMAP and the nseries boards to QOM
will need to either implement the card switch properly or move
the enable hack into the OMAP MMC controller model.
In the SDBus API, the old-style use of sd_set_cb to register some
qemu_irqs for notification of card insertion and write-protect
toggling is replaced with methods in the SDBusClass which the
card calls on status changes and methods in the SDClass which
the controller can call to find out the current status. The
query methods will allow us to remove the abuse of the 'register
irqs' API by controllers in their reset methods to trigger
the card to tell them about the current status again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-5-git-send-email-peter.maydell@linaro.org
Convert the sd_reset() function into a proper Device reset method.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-4-git-send-email-peter.maydell@linaro.org
Turn the SD card into a QOM device.
This conversion only changes the device itself; the various
functions which are effectively methods on the device are not
touched at this point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-3-git-send-email-peter.maydell@linaro.org
The following commits will remove support for the old sdhci-pci
command line syntax using the x-drive property:
-device sdhci-pci,x-drive=mydrive -drive id=mydrive,[...]
and replace it with an explicit sd device:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
(This is OK because x-drive is experimental.)
This commit removes the x-drive property so that old style
command lines will fail with a reasonable error message:
-device sdhci-pci,x-drive=mydrive: Property '.x-drive' not found
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-2-git-send-email-peter.maydell@linaro.org
This patch removes the float_high field of PL061State, which doesn't
seem to be used anywhere. Because this changes the device state, the
version ID is also bumped up for the reason of compatiblity.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455729552-28026-3-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current QEMU doesn't clear PL061 state after reset. This causes a
weird issue with guest reboot via GPIO. Here is the device state
with two reboot requests:
(PL061State fields) data old_in_data istate
VM boot 0 0 0
After 1st ACPI reboot request 8 8 8
After VM PL061 driver ACK 8 8 0
After VM reboot 8 8 0
------------------------------------------------------------
2nd ACPI reboot request 8
In the second reboot request above, because the old_in_data field is 8,
QEMU decides that there is a pending edge IRQ already (see
pl061_update()) in input; so it doesn't raise up IRQ again. As a result
the second reboot request is lost. The correct way is to clear PL061
device state after reset.
The default reset state is found from the documents listed below. Per
Peter's suggestion that QEMU automatically calls reset function after
device initialization, this patch removes calling pl061_reset() from
pl061_initfn().
Reference:
[1] PL061 Technical Reference Manual
[2] Stellaris LM3S8962 Microcontroller Data Sheet
[3] Stellaris LM3S5P31 Microcontroller Data Sheet
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455729552-28026-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since guest_mask_notifier can not be used in vhost-user mode due
to buffering implied by unix control socket, force
use_mask_notifier on virtio devices of vhost-user interfaces, and
send correct callfd to the guest at vhost start.
Using guest_notifier_mask function in vhost-user case may
break interrupt mask paradigm, because mask/unmask is not
really done when returning from guest_notifier_mask call, instead
message is posted in a unix socket, and processed later.
Add an option boolean flag 'use_mask_notifier' to disable the use
of guest_notifier_mask in virtio pci.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The LoPAPR specification defines the following for the RTAS
power-off call: "On successful operation, does not return".
However, the implementation in QEMU currently returns and runs
the guest CPU again for some more cycles. This caused some
trouble with the new ppc implementation of the kvm-unit-tests
recently. So let's make sure that the QEMU implementation
follows the spec, thus stop the CPU to make sure that the
RTAS call does not return to the guest anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4b23699 "pseries: Add pseries-2.6 machine type" added a new
SPAPR_COMPAT_2_5 macro in the usual way. However, it didn't add this
macro to the existing SPAPR_COMPAT_2_4 macro so that pseries-2.4
inherits newer compatibility properties which are needed for 2.5 and
earlier.
This corrects the oversight.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
We currently don't emulate the I2C bus provided by CUDA.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It doesn't seem to be used, and operating systems should accept a 'unknown command' answer.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This command tells if computer should automatically wake-up after a power loss.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also implement the command, by taking device list mask into account
when polling ADB devices.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also implement the command, by removing the hardcoded period of 20 ms/50 Hz
and replacing it by the one requested by user.
Update VMState version to store this new parameter.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Next commits will port existing CUDA commands to this framework.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SET_XDABR hypercall is similar to H_SET_DABR, but also sets
the extended DABR (DABRX) register.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to LoPAPR, h_set_dabr should simply set DABRX to 3
(if the register is available), and load the parameter into DABR.
If DABRX is not available, the hypervisor has to check the
"Breakpoint Translation" bit of the DABR register first.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a very simple hypercall that only sets up the SPRG0
register for the guest (since writing to SPRG0 was only permitted
to the hypervisor in older versions of the PowerISA).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
htab_save_first_pass could return without finishing its work due to
timeout. The patch checks if another invocation of it is necessary and
will call it in htab_save_complete if necessary.
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[removed overlong line]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With HV KVM, the guest's hash page table (HPT) is managed by the kernel and
not directly accessible to QEMU. This means that spapr->htab is NULL
and normally env->external_htab would also be NULL for each cpu.
However, that would cause ppc_hash64_load_hpte*() to do the wrong thing in
the few cases where QEMU does need to load entries from the in-kernel HPT.
Specifically, seeing external_htab is NULL, they would look for an HPT
within the guest's address space instead.
To stop that we have an ugly hack in the pseries machine type code to
set external htab to (void *)1 instead.
This patch removes that hack by having ppc_hash64_load_hpte*() explicitly
check kvmppc_kern_htab instead, which makes more sense.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At the moment the size of the hash page table (HPT) is fixed based on the
maximum memory allowed to the guest. As such, we allocate the table during
machine construction, and just clear it at reset.
However, we're planning to implement a PAPR extension allowing the hash
page table to be resized at runtime. This will mean that on reset we want
to revert it to the default size. It also means that when migrating, we
need to make sure the destination allocates an HPT of size matching the
host, since the guest could have changed it before the migration.
This patch replaces the spapr_alloc_htab() and spapr_reset_htab() functions
with a new spapr_reallocate_hpt() function. This is called at reset and
inbound migration only, not during machine init any more.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At present we calculate the recommended hash page table (HPT) size for a
pseries guest just once in ppc_spapr_init() before allocating the HPT.
In future patches we're going to want this calculation in other places, so
this splits it out into a helper function. While we're at it, change the
calculation to use ctz() instead of an explicit loop.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When migrating the 'pseries' machine type with KVM, we use a special fd
to access the hash page table stored within KVM. Usually, this fd is
opened at the beginning of migration, and kept open until the migration
is complete.
However, if there is a guest reset during the migration, the fd can become
stale and we need to re-open it. At the moment we use an 'htab_fd_stale'
flag in sPAPRMachineState to signal this, which is checked in the migration
iterators.
But that's rather ugly. It's simpler to just close and invalidate the
fd on reset, and lazily re-open it in migration if necessary. This patch
implements that change.
This requires a small addition to the machine state's instance_init,
so that htab_fd is initialized to -1 (telling the migration code it
needs to open it) instead of 0, which could be a valid fd.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
* qemu-char fixes from Daniel and Marc-André
* Bug fixes that break qemu-iotests
* Changes to fix reset from panicked state
* checkpatch false positives for designated initializers
* TLS support in the NBD servers and clients
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWw03lAAoJEL/70l94x66D/0MH/3Nctz5y1GKgAX0i6rKErV3/
hvPt6JHdWd7uBtowzO5kOy3fyOnVVST6jNHMQPAmJplUC40s6Ca0hycw9TjdJUdu
ULq0Ba7tQ1TAXowDqibtEn+iTkzSrocTJLfEglNscKzJ4y5w0vc5Bt5PgPB65mbn
oTo/YR8KyRWS6rXjyNnKb0PCaYEQziBndjuIxp9yJUsLcw1UgQJVcrUNEIiciOWu
SlWDxvJJQt5cCrTPnUXeBdjJVGaLxbcpe2llEJnIuf6Pjq4u7J0y+DJ40y0DCi9q
v3V4r16HhAGmBZNIlCtbClfhb/sRTVhONQiS9ehhROo8QCaL1psc11HWvMJ0tx0=
=CDoZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Coverity fixes for IPMI and mptsas
* qemu-char fixes from Daniel and Marc-André
* Bug fixes that break qemu-iotests
* Changes to fix reset from panicked state
* checkpatch false positives for designated initializers
* TLS support in the NBD servers and clients
# gpg: Signature made Tue 16 Feb 2016 16:27:17 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
nbd: enable use of TLS with nbd-server-start command
nbd: enable use of TLS with qemu-nbd server
nbd: enable use of TLS with NBD block driver
nbd: implement TLS support in the protocol negotiation
nbd: use "" as a default export name if none provided
nbd: always query export list in fixed new style protocol
nbd: allow setting of an export name for qemu-nbd server
nbd: make client request fixed new style if advertised
nbd: make server compliant with fixed newstyle spec
nbd: invert client logic for negotiating protocol version
nbd: convert to using I/O channels for actual socket I/O
nbd: convert blockdev NBD server to use I/O channels for connection setup
nbd: convert qemu-nbd server to use I/O channels for connection setup
nbd: convert block client to use I/O channels for connection setup
qemu-nbd: add support for --object command line arg
qom: add helpers for UserCreatable object types
ipmi: sensor number should not exceed MAX_SENSORS
mptsas: fix wrong formula
mptsas: fix memory leak
mptsas: add missing va_end
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a number of off-by-ones, one of them spotted by Coverity.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MPI_DOORBELL_WHO_INIT_SHIFT is being repeated twice. Reported
by Coverity.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Include osdep.h as the first header in nand.c; this has to be
done manually because coccinelle gets confused by the way that
this C file includes itself.
We fix some odd spacing in #includes while we are in the area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Since it can`t fail. Also modify the callers.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Also because pci_bridge_initfn() can`t fail.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit 428c3ece97 ("fix MSI injection on Xen")
inadvertently enabled the xen-specific logic unconditionally.
Limit it to only when xen is enabled.
Additionally, msix data should be read with pci_get_log
since the format is pci little-endian.
Reported-by: "Daniel P. Berrange" <berrange@redhat.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After the call to virtio_vdev_has_feature(), we only care for legacy
devices, so we don't need the extra check in virtio_is_big_endian().
Also the device_endian field is always set (VIRTIO_DEVICE_ENDIAN_UNKNOWN
may only happen on a virtio_load() path that cannot lead here), so we
don't need the assert() either.
This open codes the device_endian checking in vhost_needs_vring_endian().
It also adds a comment to explain the logic, as recent reviews showed the
cross-endian tweaks aren't that obvious.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Indeed vhost doesn't need to ask for vring endian fixing if the device is
virtio 1.0, since it is already handled by the in-kernel vhost driver. This
patch simply consolidates the logic into the existing helper.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
If target is bi-endian (ppc64, arm), the virtio_legacy_is_cross_endian()
indeed returns the runtime state of the virtio device. However, it returns
false unconditionally in the general case. This sounds a bit strange
given the name of the function.
This helper is only useful for vhost actually, where indeed non bi-endian
targets don't have to deal with cross-endian issues.
This patch moves the helper to vhost.c and gives it a more appropriate name.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Cross-endian is now handled by the core virtio-net code.
This patch reverts:
commit 5be7d9f1b1
vhost-net: tell tap backend about the vnet endianness
and
commit cf0a628f6e81bfc9b7a944fa0b80c3594836df56
net: set endianness on all backend devices
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
When running a fully emulated device in cross-endian conditions, including
a virtio 1.0 device offered to a big endian guest, we need to fix the vnet
headers. This is currently handled by the virtio_net_hdr_swap() function
in the core virtio-net code but it should actually be handled by the net
backend.
With this patch, virtio-net now tries to configure the backend to do the
endian fixing when the device starts (i.e. drivers sets the CONFIG_OK bit).
If the backend cannot support the requested endiannes, we have to fallback
onto virtio_net_hdr_swap(): this is recorded in the needs_vnet_hdr_swap flag,
to be used in the TX and RX paths.
Note that we reset the backend to the default behaviour (guest native
endianness) when the device stops (i.e. device status had CONFIG_OK bit and
driver unsets it). This is needed, with the linux tap backend at least,
otherwise the guest may lose network connectivity if rebooted into a
different endianness.
The current vhost-net code also tries to configure net backends. This will
be no more needed and will be reverted in a subsequent patch.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GtaJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini/tags/xen-2016-02-12' into staging
Xen 2016-02-12
# gpg: Signature made Fri 12 Feb 2016 17:28:09 GMT using RSA key ID 70E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
* remotes/sstabellini/tags/xen-2016-02-12:
xen: Drop __XEN_LATEST_INTERFACE_VERSION__ checks from prior to Xen 4.2
xen: move xenforeignmemory compat layer into common place
xen: drop XenXC and associated interface wrappers
xen: drop xen_xc_hvm_inject_msi wrapper
xen: drop support for Xen 4.1 and older.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This key is present in international keyboards, between left shift and
the 'Z' key, ant is described in the HID usage tables as "Keyboard
Non-US \ and |": http://www.usb.org/developers/hidpage/Hut1_12v2.pdf
This patch fixes the usb-kbd devices.
Signed-off-by: Daniel Serpell <daniel.serpell@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is an s390 boot rom which was used in s390-virtio machine.
but since commit 3538fb6f89
"s390x: remove s390-virtio machine", this file isn't used.
The only place it is referenced in the code is an unused
define ZIPL_FILENAME. There's also comment in hw/s390/ipl.c
which I'm modifying too, to refer to s390-ccw.img instead.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Return a valid value from the BCM2835 property mailbox query "get board
revision". This query is used by U-Boot. Implementing it fixes the first
obvious difference between qemu and real HW.
The value returned is currently hard-coded to match the RPi2 I own. Other
values are legal, e.g. different board manufacturer field values are
likely to exist in the wild.
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454993910-24077-1-git-send-email-swarren@wwwdotorg.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
mach-virt doesn't yet support hotplug, but command lines specifying
-smp <num>,maxcpus=<bigger-num> don't fail. Of course specifying
bigger-num as something bigger than the machine supports, e.g. > 8
on a gicv2 machine, should fail though. This fix also makes mach-
virt's max-cpus check truly consistent with the one in vl.c:main,
as the one there was already correctly checking max-cpus instead
of smp-cpus.
Reported-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454511578-24863-1-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While processing standard SD commands, the 'req.cmd' value could
lead to OOB read when used as an index into 'sd_cmd_type' or
'sd_cmd_class' arrays. Limit 'req.cmd' value to avoid such an
access.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453315857-1352-1-git-send-email-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the FIS or DMA engines are already started, do not allow them to be
"restarted." As a side-effect of this change, the migration post-load
routine must be modified to cope. If the engines are listed as "on"
in the migrated registers, they must be cleared to allow the startup
routine to see the transition from "off" to "on".
As a second side-effect, the extra argument to ahci_cond_engine_start
is removed in favor of consistent behavior.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1454103689-13042-5-git-send-email-jsnow@redhat.com
Currently, we let ahci_cond_start_engines reject weird configurations
where either the DMA (CLB) or FIS engines are said to be started, but
their matching on/off control bit is toggled off.
There should be no way to achieve this, since any time you toggle the
control bit off, the status bit should always follow synchronously.
Preparing for a refactor in cond_start_engines, move the rejection logic
straight up into post_load.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1454103689-13042-4-git-send-email-jsnow@redhat.com
Instead of relying on ahci_cond_start_engines to maintain the
engine status indicators itself, have the lower-layer CLB and FIS mapper
helpers do it themselves.
This makes the cond_start routine slightly nicer to read, and makes sure
that the status indicators will always be correct.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1454103689-13042-3-git-send-email-jsnow@redhat.com
Coverity noticed that some variables are only used by debug prints, and
called them unused. Always compile the print statements. While we're
here, print to stderr as well.
Bonus: Fix a debug printf I broke in f31937aa8
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Touched up commit message. --js]
Message-id: 1454971529-14830-1-git-send-email-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-7-git-send-email-jsnow@redhat.com
Split apart the ide_transfer_stop function into two versions: one that
interrupts and one that doesn't. The one that doesn't can be used to
halt any PIO transfers that are in the DRQ phase. It will not halt
any PIO transfers that are currently in the process of buffering data
for the guest to read.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[Renamed 'etf' to 'end_transfer_func' --js]
Message-id: 1453225191-11871-6-git-send-email-jsnow@redhat.com
Target the drain for just one device.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-5-git-send-email-jsnow@redhat.com
Buffered DMA cancellation was added to ATAPI devices and implemented
for the BMDMA HBA. Move the code over to common IDE code and allow
it to be used for any HBA.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-4-git-send-email-jsnow@redhat.com
Shuffle the reset function upwards.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-3-git-send-email-jsnow@redhat.com
This command is meant for ATAPI devices only, prohibit acknowledging it with
a command aborted response when an IDE device is busy.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-2-git-send-email-jsnow@redhat.com
We assume (and check for in configure) 4.2 or later now. In reality
all of the removed checks are for far older versions.
FMT_ioreq_size is no longer needed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Now that 4.2 and earlier are no longer supported "xc_interface *" is
always the right type for the xc interface handle.
With this we can also simplify the handling of the xenforeignmemory
compatibility wrapper by making xenforeignmemory_handle ==
xc_interface, instead of an xc_interface* and remove various uses of &
and *h.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Xen 4.2 become unsupported upstream in 09/2015 (see
http://wiki.xen.org/wiki/Xen_Release_Features). However as far as the
interfaces provided by the toolstack libraries go 4.2 and 4.3 are
indistinguishable.
Therefore drop support for Xen 4.1 and earlier which removes a whole
pile of compatibility code which makes future work (to use stable
library interfaces provided by upstream) more difficult. In particular
all supported versions now use a pointer as a libxc handle (4.1 and
earlier used an integer, resulting in various shim layers).
Also Xen 4.2 was the first version of Xen to formally support upstream
QEMU (as a preview) so that makes sense as a cut-off now.
This change drops all the configure-y and resulting ifdefs in a mostly
mechanical way. A follow up will refactor wrappers which are now
unused.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
* Coverity fixes for IPMI (Corey), i386 (Paolo), qemu-char (Paolo)
* at long last, fail on wrong .pc files if -m32 is in use (Daniel)
* qemu-char regression fix (Daniel)
* SAS1068 device (Paolo)
* memory region docs improvements (Peter)
* target-i386 cleanups (Richard)
* qemu-nbd docs improvements (Sitsofe)
* thread-safe memory hotplug (Stefan)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWug86AAoJEL/70l94x66DMMoH/A4tioDjhozDBtAkz/Ny2lZs
4Q34kQOWNnE0rIFDCsdg3Eq0QyYYpLH5tSuRZUHr37pfUyTkbff87uhnNepJaphY
YV6LmmGZmYewZuvS3+bhvYOV6Eq9Ycsi85eT860/n3FFnfklcPqFWgjjxblKewOl
Qf+9sLRVzlaeKjQPKNXbZV/4jkEF7a4W9oVKMGXcQXzyCe6vQ/ciK2jGBSLQhL9J
FYFTvm70G39t79U7zPiJNXvZBtbKJdLbqPmMBHcyVk75np3mKVln3V0gYj68ACv+
S30NedLwrxShLng98trHvD2TZqwsyxXqt7NimxLsVF5sH3GCfgYuc6fhueI0H6A=
=5xD6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* switch to C11 atomics (Alex)
* Coverity fixes for IPMI (Corey), i386 (Paolo), qemu-char (Paolo)
* at long last, fail on wrong .pc files if -m32 is in use (Daniel)
* qemu-char regression fix (Daniel)
* SAS1068 device (Paolo)
* memory region docs improvements (Peter)
* target-i386 cleanups (Richard)
* qemu-nbd docs improvements (Sitsofe)
* thread-safe memory hotplug (Stefan)
# gpg: Signature made Tue 09 Feb 2016 16:09:30 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (33 commits)
qemu-char, io: fix ordering of arguments for UDP socket creation
MAINTAINERS: add all-match entry for qemu-devel@
get_maintainer.pl: fall back to git if only lists are found
target-i386: fix PSE36 mode
docs/memory.txt: Improve list of different memory regions
ipmi_bmc_sim: Add break to correct watchdog NMI check
ipmi_bmc_sim: Fix off by one in check.
ipmi: do not take/drop iothread lock
target-i386: Deconstruct the cpu_T array
target-i386: Tidy gen_add_A0_im
target-i386: Rewrite leave
target-i386: Rewrite gen_enter inline
target-i386: Use gen_lea_v_seg in pusha/popa
target-i386: Access segs via TCG registers
target-i386: Use gen_lea_v_seg in stack subroutines
target-i386: Use gen_lea_v_seg in gen_lea_modrm
target-i386: Introduce mo_stacksize
target-i386: Create gen_lea_v_seg
char: fix repeated registration of tcp chardev I/O handlers
kvm-all: trace: strerror fixup
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It was falling through when it should have been a break. Found by
Coverity. The logic could be simplified a bit with a fallthrough,
probably the original thought, but that would be less clear, I think.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <1452519152-6500-3-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Found by Paolo.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <1452519152-6500-2-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not necessary and actually causes a hang; it was probably copied
and pasted from KVM code, that is one of the very few places that run
outside iothread lock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds the SAS1068 device, a SAS disk controller used in VMware that
is oldish but widely supported and has decent performance. Unlike
megasas, it presents itself as a SAS controller and not as a RAID
controller. The device corresponds to the mptsas kernel driver in
Linux.
A few small things in the device setup are based on Don Slutz's old
patch, but the device emulation was written from scratch based on Don's
SeaBIOS patch and on the FreeBSD and Linux drivers. It is 2400 lines
shorter than Don's patch (and roughly the same size as MegaSAS---also
because it doesn't support the similar SPI controller), implements SCSI
task management functions (with asynchronous cancellation), supports
big-endian hosts, has complete support for migration and follows the
QEMU coding standards much more closely.
To write the driver, I first split Don's patch in two parts, with
the configuration bits in one file and the rest in a separate file.
I first left mptconfig.c in place and rewrote the rest, then deleted
mptconfig.c as well. The configuration pages are still based mostly on
VirtualBox's, though not exactly the same. However, the implementation
is completely different. The contents of the pages themselves should
not be copyrightable.
Signed-off-by: Don Slutz <Don@CloudSwitch.com>
Message-Id: <1347382813-5662-1-git-send-email-Don@CloudSwitch.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SAS adapters need to access them in order to publish the SAS addresses
of the end devices connected to them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No backend was setting an error when ending the visit of a list or
implicit struct, or when moving to the next list node. Make the
callers a bit easier to follow by making this a part of the contract,
and removing the errp argument - callers can then unconditionally end
an object as part of cleanup without having to think about whether a
second error is dominated by a first, because there is no second
error.
A later patch will then tackle the larger task of splitting
visit_end_struct(), which can indeed set an error.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1454075341-13658-24-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
visit_start_struct() and visit_type_enum() had a 'kind' argument
that was usually set to either the stringized version of the
corresponding qapi type name, or to NULL (although some clients
didn't even get that right). But nothing ever used the argument.
It's even hard to argue that it would be useful in a debugger,
as a stack backtrace also tells which type is being visited.
Therefore, drop the 'kind' argument as dead.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-22-git-send-email-eblake@redhat.com>
[Harmless rebase mistake cleaned up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
No need to repeat 'struct Visitor' when we already have it in
typedefs.h. Omitting the redundant 'struct' also makes a later
patch easier to search for all object property callbacks that
are associated with a Visitor.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-18-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Rework the control flow of balloon_stats_get_all() to make it
easier for a later patch to split visit_end_struct(). Also
switch to the uint64 visitor to match the data type.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1454075341-13658-10-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Done with the Coccinelle semantic patch from commit 007b065, plus
manual clean up of dead variables.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1452783732-6581-1-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtj8KAAoJECgfDbjSjVRpBIQIAJSB9xwTcBLXwD0+8z5lqjKC
GTtuVbHU0+Y/eO8O3llN5l+SzaRtPHo18Ele20Oz7IQc0ompANY273K6TOlyILwB
rOhrub71uqpOKbGlxXJflroEAXb78xVK02lohSUvOzCDpwV+6CS4ZaSer7yDCYkA
MODZj7rrEuN0RmBWqxbs1R7Mj2CeQJzlgTUNTBGCLEstoZGFOJq8FjVdG5P1q8vI
fnI9mGJ1JsDnmcUZe/bTFfB4VreqeQ7UuGyNAMMGnvIbr0D1a+CoaMdV7/HZ+KyT
5TIs0siVdhZei60A/Cq2OtSVCbj5QdxPBLhZfwJCp6oU4lh2U5tSvva0mh7MwJ0=
=D/cA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc and misc cleanups and fixes, virtio optimizations
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sat 06 Feb 2016 18:44:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (45 commits)
net: set endianness on all backend devices
fix MSI injection on Xen
intel_iommu: large page support
dimm: Correct type of MemoryHotplugState->base
pc: set the OEM fields in the RSDT and the FADT from the SLIC
acpi: add function to extract oem_id and oem_table_id from the user's SLIC
acpi: expose oem_id and oem_table_id in build_rsdt()
acpi: take oem_id in build_header(), optionally
pc: Eliminate PcGuestInfo struct
pc: Move APIC and NUMA data from PcGuestInfo to PCMachineState
pc: Move PcGuestInfo.fw_cfg to PCMachineState
pc: Remove PcGuestInfo.isapc_ram_fw field
pc: Remove RAM size fields from PcGuestInfo
pc: Remove compat fields from PcGuestInfo
acpi: Don't save PcGuestInfo on AcpiBuildState
acpi: Remove guest_info parameters from functions
pc: Simplify xen_load_linux() signature
pc: Simplify pc_memory_init() signature
pc: Eliminate struct PcGuestInfoState
pc: Move PcGuestInfo declaration to top of file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 5be7d9f1b1
vhost-net: tell tap backend about the vnet endianness
makes vhost net to set the endianness of the device, but only for
the first device.
In case of multiqueue, we have multiple devices... This patch sets the
endianness for all the devices of the interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
On Xen MSIs can be remapped into pirqs, which are a type of event
channels. It's mostly for the benefit of PCI passthrough devices, to
avoid the overhead of interacting with the emulated lapic.
However remapping interrupts and MSIs is also supported for emulated
devices, such as the e1000 and virtio-net.
When an interrupt or an MSI is remapped into a pirq, masking and
unmasking is done by masking and unmasking the event channel. The
masking bit on the PCI config space or MSI-X table should be ignored,
but it isn't at the moment.
As a consequence emulated devices which use MSI or MSI-X, such as
virtio-net, don't work properly (the guest doesn't receive any
notifications). The mechanism was working properly when xen_apic was
introduced, but I haven't narrowed down which commit in particular is
causing the regression.
Fix the issue by ignoring the masking bit for MSI and MSI-X which have
been remapped into pirqs.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current intel_iommu only supports 4K page which may not be sufficient
to cover guest working set. This patch tries to enable 2M and 1G mapping
for intel_iommu. This is also useful for future device IOTLB
implementation to have a better hit rate.
Major work is adding a page mask field on IOTLB entry to make it
support large page. And also use the slpte level as key to do IOTLB
lookup. MAMV was increased to 18 to support direct invalidation for 1G
mapping.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Microsoft spec about the SLIC and MSDM ACPI tables at
<http://go.microsoft.com/fwlink/p/?LinkId=234834> requires the OEM ID and
OEM Table ID fields to be consistent between the SLIC and the RSDT/XSDT.
That further affects the FADT, because a similar match between the FADT
and the RSDT/XSDT is required by the ACPI spec in general.
This patch wires up the previous three patches.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Steven Newbury <steve@snewbury.org.uk>
The acpi_get_slic_oem() function stores pointers to these fields in the
(first) SLIC table that the user passes in with the -acpitable switch.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Steven Newbury <steve@snewbury.org.uk>
Since build_rsdt() is implemented as common utility code (in
"hw/acpi/aml-build.c"), it should expose -- and forward -- the oem_id and
oem_table_id parameters between board code and the generic build_header()
function.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
This patch is the continuation of commit 8870ca0e94 ("acpi: support
specified oem table id for build_header"). It will allow us to control the
OEM ID field too in the SDT header.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> (maintainer:NVDIMM)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
The struct is not used for anything, now.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The code can use the PCMachineClass.pci_enabled field directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The ACPI code can use the PCMachineState fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Remove the fields: legacy_acpi_table_size, has_acpi_build,
has_reserved_memory, and rsdp_in_ram from PcGuestInfo, and let
the existing code use the PCMachineClass fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We don't need to save the pointer on AcpiBuildState, as it is not
used anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can use PC_MACHINE(qdev_get_machine())->acpi_guest_info to get
guest_info.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Instead of allocating a new struct just for PcGuestInfo and the
mchine_done Notifier, place them inside PCMachineState.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
>From the specs (20.8 Get Device GUID Command), the command needs to
return a GUID (Globally Unique ID), or UUID, that should never change
over the lifetime of the device. qemu_uuid looked like a good
candidate to start with but we could use a specific BMC property also
if needed.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is a simulator. Just return an unknown cause (0).
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, sdr attributes are identified using byte offsets and this
can be a bit confusing.
This patch adds a struct ipmi_sdr_compact conforming to the IPMI specs
and replaces byte offsets with names. It also introduces and uses a
struct ipmi_sdr_header in sections of the code where no assumption is
made on the type of SDR. This leave rooms to potential usage of other
types in the future.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The IPMI BMC simulator populates the SDR table with a set of initial
SDRs. The length of each SDR is taken from the record itself (byte 4)
which does not include the size of the header. But, the full length
(header + data) is required by the sdr_add_entry() routine.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ARRAY_SIZE() is simple to use and removes the need to pre-define
the size of the command arrays.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Each routine using the IPMI_ADD_RSP_DATA, IPMI_CHECK_CMD_LEN or
IPMI_CHECK_RESERVATION macros needs to define a goto label 'out' to
handle hidden errors. Using directly a return statement has the same
effect and it removes the fact that 'out' needs to be defined.
The code exits in ipmi_sim_handle_command() are a little different
from the rest and a "possible" error in the macro IPMI_ADD_RSP_DATA is
handled before making use of it. This might be a bit excessive as a
minimum response len is currently 300 bytes and the patch checks that
at least 3 are available.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI devices can't be plugged directly into PCI extra root bridges
because their resources can't be computed by firmware before the ACPI
tables are loaded.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fill in an element of the used ring with a single combined access to the
guest physical memory, rather than using two separated accesses.
This reduces the overhead due to expensive address translation.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Message-Id: <e4a89a767a4a92cbb6bcc551e151487eb36e1722.1450218353.git.v.maffione@gmail.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtqueue_pop() implementation needs to check if the avail ring
contains some pending buffers. To perform this check, it is not
always necessary to fetch the avail_idx in the VQ memory, which is
expensive. This patch introduces a shadow variable tracking avail_idx
and modifies virtio_queue_empty() to access avail_idx in physical
memory only when necessary.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Message-Id: <b617d6459902773d9f4ab843bfaca764f5af8eda.1450218353.git.v.maffione@gmail.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Accessing used_idx in the VQ requires an expensive access to
guest physical memory. Before this patch, 3 accesses are normally
done for each pop/push/notify call. However, since the used_idx is
only written by us, we can track it in our internal data structure.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Message-Id: <3d062ec54e9a7bf9fb325c1fd693564951f2b319.1450218353.git.v.maffione@gmail.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Compared to vring, virtio has a performance penalty of 10%. Fix it
by combining all the reads for a descriptor in a single address_space_read
call. This also simplifies the code nicely.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Build the addresses and s/g lists on the stack, and then copy them
to a VirtQueueElement that is just as big as required to contain this
particular s/g list. The cost of the copy is minimal compared to that
of a large malloc.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Build the addresses and s/g lists on the stack, and then copy them
to a VirtQueueElement that is just as big as required to contain this
particular s/g list. The cost of the copy is minimal compared to that
of a large malloc.
When virtqueue_map is used on the destination side of migration or on
loadvm, the iovecs have already been split at memory region boundary,
so we can just reuse the out_num/in_num we find in the file.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate the arrays for in_addr/out_addr/in_sg/out_sg outside the
VirtQueueElement. For now, virtqueue_pop and vring_pop keep
allocating a very large VirtQueueElement.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move allocation to virtio functions also when loading/saving a
VirtQueueElement. This will also let the load/save functions
keep backwards compatibility when the VirtQueueElement layout
is changed.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The return code of virtqueue_pop/vring_pop is unused except to check for
errors or 0. We can thus easily move allocation inside the functions
and just return a pointer to the VirtQueueElement.
The advantage is that we will be able to allocate only the space that
is needed for the actual size of the s/g list instead of the full
VIRTQUEUE_MAX_SIZE items. Currently VirtQueueElement takes about 48K
of memory, and this kind of allocation puts a lot of stress on malloc.
By cutting the size by two or three orders of magnitude, malloc can
use much more efficient algorithms.
The patch is pretty large, but changes to each device are testable
more or less independently. Splitting it would mostly add churn.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The next patch will make virtqueue_pop/vring_pop allocate memory for
the VirtQueueElement. In some cases (blk, scsi, gpu) the device wants
to extend VirtQueueElement with device-specific fields and, until now,
the place of the VirtQueueElement within the containing struct didn't
matter. When allocating the entire block in virtqueue_pop/vring_pop,
however, the containing struct must basically be a "subclass" of
VirtQueueElement, with the VirtQueueElement as the first field. Make
that the case for blk and scsi; gpu is already doing it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Since both tables are built dynamically now,
there is no point in keeping ASL in them in separate
tables.
So do the same as we do for ARM where we have only
DSDT table, i.e. move SSDT ASL into DSDT and
drop SSDT altogether.
This patch doesn't change moved SSDT ASL in any way,
but it opens a way to relatively independently simplify
generated ASL on per device/subsystem basis in
followup series.
It also simplifies bios-tables-test where expected
SSDT blobs could be dropped and only DSDT ones
have to be maintained.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I misunderstood the vmstate macro definition when I reworked the
virtio .get/.put.
The VMSTATE_STRUCT_VARRAY_KNOWN, was described as being for "a
variable length array (i.e. _type *_field) but we know the
length". However it actually specified operation for arrays embedded in
the struct (i.e. _type _field[]) since it lacked the VMS_POINTER
flag. This caused offset calculation to be completely off, examining and
potentially sending random data instead of the VirtQueue content.
Replace the otherwise unused VMSTATE_STRUCT_VARRAY_KNOWN with a
VMSTATE_STRUCT_VARRAY_POINTER_KNOWN that includes the VMS_POINTER flag
(so now actually doing what it advertises) and use it in the virtio
migration code.
Fixes and description as per Sascha's suggestions/debug.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reported-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Tested-By: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-By: Sascha Silbe <silbe@linux.vnet.ibm.com>
Fixes: 50e5ae4dc3
Fixes: 2cf0148674
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Version: GnuPG v1
iQEcBAABAgAGBQJWswswAAoJEO8Ells5jWIRmuAIAKfexolRpauVFoMt2w69Yrk4
0XhaAuSaazsfU06azXKjrchBUgXbw4Y6lw3tkTos4lnd8m1ovfAzSTS4q28rZ+Tf
u5M06Fi13oyhEViGS4gt6gTwmYPTx2FTBDMCL1OZvka7GPbVsweQn0IS18j1Q2xL
ps2kruNTad7mUa2EypuBugm3woL8kGupLUX63aWKmnvqobwFDNTKJLWiFn5eXlbg
Zq7LxmC4R3A5K9rD8wN16ScaK3RH2x83DXaRoddtSIRwdldxG9ZCv2oFKPZrr6WA
HsJIjurMTXhaRxNL3PsGMd/MbT7gmNF5muq8kZnkORmGxfMvi3RUuBdyhrq1I0w=
=2Uz/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 04 Feb 2016 08:26:24 GMT using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net/filter: Fix the output information for command 'info network'
net: always walk through filters in reverse if traffic is egress
net: netmap: use nm_open() to open netmap ports
e1000: eliminate infinite loops on out-of-bounds transfer start
slirp: Adding family argument to tcp_fconnect()
slirp: Make udp_attach IPv6 compatible
slirp: Add sockaddr_equal, make solookup family-agnostic
slirp: Factorizing and cleaning solookup()
slirp: Factorizing address translation
slirp: Make Socket structure IPv6 compatible
slirp: Adding address family switch for produced frames
slirp: Generalizing and neutralizing ARP code
slirp: goto bad in udp_input if sosendto fails
cadence_gem: fix buffer overflow
net: cadence_gem: check packet size in gem_recieve
qemu-doc: Do not promote deprecated -smb and -redir options
net/slirp: Tell the users when they are using deprecated options
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1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=UnwI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into staging
# gpg: Signature made Wed 03 Feb 2016 20:29:54 GMT using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
* remotes/jnsnow/tags/ide-pull-request:
dma: remove now useless DMA_* functions
sb16: use IsaDma interface instead of global DMA_* functions
gus: use IsaDma interface instead of global DMA_* functions
cs4231a: use IsaDma interface instead of global DMA_* functions
fdc: use IsaDma interface instead of global DMA_* functions
sparc64: disable floppy DMA
sparc: disable floppy DMA
magnum: disable floppy DMA for now
i8257: implement the IsaDma interface
isa: add an ISA DMA interface, and store it within the ISA bus
i8257: move state definition to new independent header
i8257: QOM'ify
i8257: add missing const
i8257: make the DMA running method per controller
i8257: rename functions to start with i8257_ prefix
i8257: rename struct dma_regs to I8257Regs
i8257: rename struct dma_cont to I8257State
i8257: pass ISA bus to DMA_init() function
i82374: device only existed as ISA device, so simplify device
fdc: fix detection under Linux
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The start_xmit() and e1000_receive_iov() functions implement DMA transfers
iterating over a set of descriptors that the guest's e1000 driver
prepares:
- the TDLEN and RDLEN registers store the total size of the descriptor
area,
- while the TDH and RDH registers store the offset (in whole tx / rx
descriptors) into the area where the transfer is supposed to start.
Each time a descriptor is processed, the TDH and RDH register is bumped
(as appropriate for the transfer direction).
QEMU already contains logic to deal with bogus transfers submitted by the
guest:
- Normally, the transmit case wants to increase TDH from its initial value
to TDT. (TDT is allowed to be numerically smaller than the initial TDH
value; wrapping at or above TDLEN bytes to zero is normal.) The failsafe
that QEMU currently has here is a check against reaching the original
TDH value again -- a complete wraparound, which should never happen.
- In the receive case RDH is increased from its initial value until
"total_size" bytes have been received; preferably in a single step, or
in "s->rxbuf_size" byte steps, if the latter is smaller. However, null
RX descriptors are skipped without receiving data, while RDH is
incremented just the same. QEMU tries to prevent an infinite loop
(processing only null RX descriptors) by detecting whether RDH assumes
its original value during the loop. (Again, wrapping from RDLEN to 0 is
normal.)
What both directions miss is that the guest could program TDLEN and RDLEN
so low, and the initial TDH and RDH so high, that these registers will
immediately be truncated to zero, and then never reassume their initial
values in the loop -- a full wraparound will never occur.
The condition that expresses this is:
xdh_start >= s->mac_reg[XDLEN] / sizeof(desc)
i.e., TDH or RDH start out after the last whole rx or tx descriptor that
fits into the TDLEN or RDLEN sized area.
This condition could be checked before we enter the loops, but
pci_dma_read() / pci_dma_write() knows how to fill in buffers safely for
bogus DMA addresses, so we just extend the existing failsafes with the
above condition.
This is CVE-2016-1981.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Prasad Pandit <ppandit@redhat.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-stable@nongnu.org
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1296044
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
gem_transmit copies a packet from guest into an tx_packet[2048]
array on stack, with size limited by descriptor length set by guest. If
guest is malicious and specifies a descriptor length that is too large,
and should packet size exceed array size, this results in a buffer
overflow.
Reported-by: 刘令 <liuling-it@360.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
While receiving packets in 'gem_receive' routine, if Frame Check
Sequence(FCS) is enabled, it copies the packet into a local
buffer without checking its size. Add check to validate packet
length against the buffer size to avoid buffer overflow.
Reported-by: Ling Liu <liuling-it@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJWsiEWAAoJEJykq7OBq3PIGXYIALsxSU9HYOBqt/7J5E07EUxS
ef3pu/CnMSHw3I/oLVe+pdpwyKMEhRRa75t8DSl4+UodsPXyZ/YtuBTm2v7J+FXD
tjOoDYimAuDqeJU+km4O3PRUKSUKIlo0V4g7DRWF1qCCC4xw8SwmkBvfax7oFf3a
ew3s0Lw/v11/foe5lKTkgTBgoXKk/Oc1E3rhSsOb7WvZq0CbrhRV3R5Lp0jbXkjF
1LMijbsQvzQY7v07r4FcZ2vwhdI5eUXQOKg6sHMBqBbNdrR0zEQeylgdXq7H2rqm
RhdkK4Dd1bs4K1gk4TXNhysd7/U5gRJhGqeBkYCI12lNY9AJwyH0OBcBxGZBV6U=
=pTqw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Wed 03 Feb 2016 15:47:34 GMT using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/tracing-pull-request:
log: add "-d trace:PATTERN"
trace: switch default backend to "log"
trace: convert stderr backend to log
log: move qemu-log.c into util/ directory
log: do not unnecessarily include qom/cpu.h
trace: add "-trace help"
trace: add "-trace enable=..."
trace: no need to call trace_backend_init in different branches now
trace: split trace_init_file out of trace_init_backends
trace: split trace_init_events out of trace_init_backends
trace: fix documentation
trace: track enabled events in a separate array
trace: count number of enabled events
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keep only DMA_init function as a wrapper around DMA controllers creation.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-20-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
All functions relative to DMA (DMA_*() functions) are stubs on sparc64 platform.
Disable the DMA of the floppy controller, instead of calling these stubs.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-15-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
All functions relative to DMA (DMA_*() functions) are stubs on sparc platform.
Disable the DMA in the floppy controller, instead of calling these stubs.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-14-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
Floppy uses the DMA controller in rc4030 chipset, and not the i8259 from the ISA bus.
It's better to disable DMA than to call the wrong DMA controller.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-13-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
Rewrite the global DMA_*() functions to use the IsaDma interface.
Note that these functions will be deleted in a few commits.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-12-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
This will permit to deprecate global DMA_*() functions.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-11-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
We will now be able to embed the i8257 interrupt controller in another object.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-10-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
This removes some static/global variables, and we're now running only the
required controller (master or slave)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-7-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
i8257 DMA controller exists on one ISA bus, so let's specify it at initialization.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-3-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
Accidentally, I removed a "feature" where empty drives had geometry
values applied to them, which allows seek on empty drives to work
"by accident," as QEMU actually tries to disallow that.
Seeks on empty drives should work, though, but the easiest thing is to
restore the misfeature where empty drives have non-zero geometries
applied.
Document the hack accordingly.
[Maintainer edit]
This fix corrects a regression introduced in d5d47efc, where
pick_geometry was modified such that it would not operate on empty
drives, and as a result if there is no diskette inserted, QEMU
no longer populates it with geometry bounds. As a result, seek fails
when QEMU denies to move the current track, but reports success anyway.
This can confuse the guest, leading to kernel panics in the guest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1454106932-17236-1-git-send-email-jsnow@redhat.com
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new version is slightly different, to support Rasbperry Pi (in
particular, Pi1's arm11 core which doesn't support v7 instructions
such as MOVW).
Tested-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the SoC for Raspberry Pi 2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This module is specific to the bcm2836 (Pi2). It implements the top
level interrupt controller, and mailboxes used for inter-processor
synchronisation.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device maintains all the non-CPU peripherals on bcm2835 (Pi1)
which are also present on bcm2836 (Pi2). It also implements the
private address spaces used for DMA and mailboxes.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This sits behind the mailbox interface, and implements
request/response queries for system properties. The
framebuffer-related properties will be added in a later patch.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the system mailboxes which are used to communicate with a
number of GPU peripherals on Pi/Pi2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
in current impl. condition
build_madt() {
...
if (test_bit(i, cpuinfo->found_cpus))
is always true since loop handles only present CPUs
in range [0..smp_cpus).
But to fill usless cpuinfo->found_cpus we do unnecessary
scan over QOM tree to find the same CPUs.
So mark GICC as present always and drop not needed
code that fills cpuinfo->found_cpus.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454323689-248759-1-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting Linux on AArch64 enabled cores, setup EL1 and
EL2 to use AArch64.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch is the ACPI equivalent of "hw/arm/virt: Add always-on
property to the virt board timer". The timer is always on, and
thus setting this informs Linux that it may switch off the periodic
timer. Switching off the periodic timer substantially reduces the
number of interrupts the host needs to inject.
Testing note: AArch64 guests (the only ones currently booting with
ACPI) do not actually need this patch to determine it can turn the
periodic timer off. I therefore used a hacked guest kernel to ensure
this patch works as the equivalent DT patch does.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1453380893-26174-1-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So we can stop rendering for a while in case we have to.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
We'll go take out the commands we receive out of the virt queue and put
them into a linked list, to decouple virtio queue handling from actual
command processing.
Also move cmd processing to new virtio_gpu_handle_ctrl func, so we can
easily kick it from different places.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Found by Coverity Scan, buf not freed on error.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Split the bits that require it to exec/log.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1452174932-28657-8-git-send-email-den@openvz.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWsOYgAAoJEDuxQgLoOKyt/DUH/1hIzxS+qyh3iko0B5O0aWny
PJObgy4004T9yClYDOPRvoNfoFAw63iOkfnMArnzTETEaPR94DJXYM0uTLY8Pyht
wNcAZm44FlYKhEOOXqFslE6Z1arOR2s2wTYGn4s6BvkGbGlHCWr7N7n5trMpLAMJ
/jAT+PNAgJrxlI/vVDeitFhQYABwXmBdPpf1kgn28IepBAI62de1rJubX27WoWuQ
j1+VwhbKCWFwE4PqDHVVo2Wm+Gv5A53alB6Adpx6+5xXYLWBBq/nNg1SwDXfD0+q
gk7Qiwso+7fFWMX6mx2qgvdXBI2R4NlLoQAzA6sjWF1v4hf76/wjNQLsg+1+qXo=
=BEb2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-for-peter-2016-02-02' into staging
Block patches
# gpg: Signature made Tue 02 Feb 2016 17:23:44 GMT using RSA key ID E838ACAD
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"
* remotes/maxreitz/tags/pull-block-for-peter-2016-02-02: (50 commits)
block: qemu-iotests - add test for snapshot, commit, snapshot bug
block: set device_list.tqe_prev to NULL on BDS removal
iotests: Add "qemu-img map" test for VMDK extents
qemu-img: Make MapEntry a QAPI struct
qemu-img: In "map", use the returned "file" from bdrv_get_block_status
block: Use returned *file in bdrv_co_get_block_status
vmdk: Return extent's file in bdrv_get_block_status
vmdk: Fix calculation of block status's offset
vpc: Assign bs->file->bs to file in vpc_co_get_block_status
vdi: Assign bs->file->bs to file in vdi_co_get_block_status
sheepdog: Assign bs to file in sd_co_get_block_status
qed: Assign bs->file->bs to file in bdrv_qed_co_get_block_status
parallels: Assign bs->file->bs to file in parallels_co_get_block_status
iscsi: Assign bs to file in iscsi_co_get_block_status
raw: Assign bs to file in raw_co_get_block_status
qcow2: Assign bs->file->bs to file in qcow2_co_get_block_status
qcow: Assign bs->file->bs to file in qcow_co_get_block_status
block: Add "file" output parameter to block status query functions
block: acquire in bdrv_query_image_info
iotests: Add test for block jobs and BDS ejection
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make use of the BDS-BB removal and insertion notifiers to remove or set
up, respectively, virtio-scsi's op blockers.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Put the code for setting up and removing op blockers into an own
function, respectively. Then, we can invoke those functions whenever a
BDS is removed from an virtio-blk BB or inserted into it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts the changes that commit
2e1280e8ff applied to hw/block/fdc.c;
also, an additional case of drv->media_inserted use has crept in since,
which is replaced by a call to blk_is_inserted().
That commit changed tests/fdc-test.c, too, because after it, one less
TRAY_MOVED event would be emitted when executing 'change' on an empty
drive. However, now, no TRAY_MOVED events will be emitted at all, and
the tray_open status returned by query-block will always be false,
necessitating (different) changes to tests/fdc-test.c and iotest 118,
which is why this patch is not a pure revert of said commit.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 1454096953-31773-4-git-send-email-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
After clearing the status register we also have to update the irq line
status. Otherwise a irq which happends to be pending at reset time
causes a interrupt storm. And the guest can't stop as the status
register doesn't indicate any pending interrupt.
Both NetBSD and FreeBSD hang on shutdown because of that.
Cc: qemu-stable@nongnu.org
Reported-by: Andrey Korolyov <andrey@xdel.ru>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1453203884-4125-1-git-send-email-kraxel@redhat.com
While processing isochronous transfer descriptors(iTD), the page
select(PG) field value could lead to an OOB read access. Add
check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1453233406-12165-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453138432-8324-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Simplify the interrupt handling by having a single callback on irq&msi
cases. Remove usage of CharDriver, replace it with
qemu_set_fd_handler(). Use event_notifier_test_and_clear() to read the
eventfd.
Before this patch, ivshmem writes the first byte received to
s->intrstatus. But ivshmem_device_spec.txt says "The status register is
set to 1 when an interrupt occurs." Fortunately, the byte usually comes
from another ivshmem device, and those always write 1.
After this commit, follows the specification, set to 1 when an interrupt
occurs.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Call ivshmem_setup_interrupts() with or without MSI, always allocate
msi_vectors that is going to be used in all case in the following patch.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Fix crash when msi=false introduced in 660c97ee (msi_vectors is NULL in
this case)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
