Convert the insns in the one-register-and-immediate group to decodetree.
In the new decode, our asimd_imm_const() function returns a 64-bit value
rather than a 32-bit one, which means we don't need to treat cmode=14 op=1
as a special case in the decoder (it is the only encoding where the two
halves of the 64-bit value are different).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-10-peter.maydell@linaro.org
Convert the VCVT fixed-point conversion operations in the
Neon 2-regs-and-shift group to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-9-peter.maydell@linaro.org
Convert the VSHLL and VMOVL insns from the 2-reg-shift group
to decodetree. Since the loop always has two passes, we unroll
it to avoid the awkward reassignment of one TCGv to another.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-8-peter.maydell@linaro.org
Convert the VQSHLU and QVSHL 2-reg-shift insns to decodetree.
These are the last of the simple shift-by-immediate insns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-5-peter.maydell@linaro.org
Convert the VSRA, VSRI, VRSHR, VRSRA 2-reg-shift insns to decodetree.
(These are the last instructions in the group that are vectorized;
the rest all require looping over each element.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-4-peter.maydell@linaro.org
Convert the VSHR 2-reg-shift insns to decodetree.
Note that unlike the legacy decoder, we present the right shift
amount to the trans_ function as a positive integer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-3-peter.maydell@linaro.org
Convert the VSHL and VSLI insns from the Neon 2-registers-and-a-shift
group to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200522145520.6778-2-peter.maydell@linaro.org
Rather than passing an opcode to a helper, fully decode the
operation at translate time. Use clear_tail_16 to zap the
balance of the SVE register with the AdvSIMD write.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-7-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than passing an opcode to a helper, fully decode the
operation at translate time. Use clear_tail_16 to zap the
balance of the SVE register with the AdvSIMD write.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-6-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not yet convert the helpers to loop over opr_sz, but the
descriptor allows the vector tail to be cleared. Which fixes
an existing bug vs SVE.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not yet convert the helpers to loop over opr_sz, but the
descriptor allows the vector tail to be cleared. Which fixes
an existing bug vs SVE.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this conversion, we will be able to use the same helpers
with sve. This also fixes a bug in which we failed to clear
the high bits of the SVE register after an AdvSIMD operation.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this conversion, we will be able to use the same helpers
with sve. In particular, pass 3 vector parameters for the
3-operand operations; for advsimd the destination register
is also an input.
This also fixes a bug in which we failed to clear the high bits
of the SVE register after an AdvSIMD operation.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200514212831.31248-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As these declarations are restricted to !CONFIG_USER_ONLY in
helper.c, only declare them when system-mode emulation is used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-8-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
All this code is guarded checking CONFIG_USER_ONLY definition.
Drop the duplicated checks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-7-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The decode_basedisp*() methods are only used in ioinst.c,
which is only build in system-mode emulation.
I/O instructions are privileged, and other S instructions
are decoded elsewhere.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-6-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We need some little help in the code to reduce the valgrind noise.
This patch does this with some designated initializers for the cpu
model features and subfunctions.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200429074201.100924-1-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We usually use '_do_' for internal functions. Rename
memory_region_do_writeback() as memory_region_writeback().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20200508062456.23344-2-philmd@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Ibex is a small and efficient, 32-bit, in-order RISC-V core with
a 2-stage pipeline that implements the RV32IMC instruction set
architecture.
For more details on lowRISC see here:
https://github.com/lowRISC/ibex
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
The PMP is enabled by default via the "pmp" property so there is no need
for us to set it in the init function. As all CPUs have PMP support just
remove the set_feature() call in the CPU init functions.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Previously if we didn't enable the MMU it would be enabled in the
realize() function anyway. Let's ensure that if we don't want the MMU we
disable it. We also don't need to enable the MMU as it will be enabled
in realize() by default.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The reset vector is set in the init function don't set it again in
realize.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The RISC-V ISA spec version 1.09.1 has been deprecated in QEMU since
4.1. It's not commonly used so let's remove support for it.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signal handling support for NetBSD arm/aarch64
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAl7WgZkdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8ZZwf9Flw0VHTBBzsZHPjL
JVOdJsz8pnQLRDxk9JUo7D40xehpN1oE5mFCV5aFNMSz929r7OB5WfUHsyNpbms/
aCDz2ADRscBZ4xEZY9cxUYiNzq4fb3Hez64ibGbRm3uHU1C2pPNDRlFpL9aFQMCE
elhn54hwOAZUZAAKszepClHGglPffijY5QU5VX6Gq6nmqEmCBlA8lkxMtaV/NRnS
QfskDF4KvglGqGDCcKI2tfotu5Y9k3R4yh7Nzc2JnotbHk4WrNbhBl6r9KcdXddi
uQng4J0zhBa1Kq4ENdpKgAqN/ZNVEbsFzev5aY77UD76cnxqbQQ7hfXl2gAORp6m
Vy5lVw==
=nRee
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-tcg-20200602' into staging
Vector rotate support
Signal handling support for NetBSD arm/aarch64
# gpg: Signature made Tue 02 Jun 2020 17:43:05 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-tcg-20200602:
accel/tcg: Provide a NetBSD specific aarch64 cpu_signal_handler
accel/tcg: Adjust cpu_signal_handler for NetBSD/arm
tcg: Improve move ops in liveness_pass_2
target/s390x: Use tcg_gen_gvec_rotl{i,s,v}
target/ppc: Use tcg_gen_gvec_rotlv
tcg/ppc: Implement INDEX_op_rot[lr]v_vec
tcg/aarch64: Implement INDEX_op_rotl{i,v}_vec
tcg/i386: Implement INDEX_op_rotl{i,s,v}_vec
tcg: Implement gvec support for rotate by scalar
tcg: Remove expansion to shift by vector from do_shifts
tcg: Implement gvec support for rotate by vector
tcg: Implement gvec support for rotate by immediate
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Merge VERLL and VERLLV into op_vesv and op_ves, alongside
all of the other vector shift operations.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
this also removes tricore_cpu_get_phys_page_attrs_debug() as it was a
temporary fix from b190f477e2.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20200529072148.284037-5-kbastian@mail.uni-paderborn.de>
this is needed for remote gdb connections.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20200529072148.284037-4-kbastian@mail.uni-paderborn.de>
this allows us to remove the references to env from ctx. This also fixes
a segfault that was due to the unititalized ctx->env ptr.
Reported-by: Andreas Konopik <andreas.konopik@fau.de>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20200529072148.284037-3-kbastian@mail.uni-paderborn.de>
EXCP_DEBUG is the only user. If we encounter a jump in tricore-gdb it's
target was overwritten by generate_qemu_excp() and we would never leave.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20200529072148.284037-2-kbastian@mail.uni-paderborn.de>
Traditionally, MIPS use 4KB page size, but Loongson prefer 16KB page
size in system emulator. So, let's define TARGET_PAGE_BITS_VARY and
TARGET_PAGE_BITS_MIN to support variable page size.
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Signed-off-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Message-Id: <1586337380-25217-1-git-send-email-chenhc@lemote.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
x86_cpu_load_model() is wrong that way. Harmless, because its @errp
is always &error_abort. To fix, cut out the @errp middleman.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200505101908.6207-11-armbru@redhat.com>
Commit e47970f51d "s390x/cpumodel: Fix query-cpu-model-FOO error API
violations" neglected to change visit_check_struct()'s Error **
argument along with the others. If visit_check_struct() failed, we'd
take the success path. Fortunately, it can't fail here:
qobject_input_check_struct() checks we consumed the whole dictionary,
and to get here, we did. Fix it anyway.
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505101908.6207-4-armbru@redhat.com>
The penultimate argument of function ppc_radix64_partition_scoped_xlate()
has the bool type.
Fixes: d04ea940c5 "target/ppc: Add support for Radix partition-scoped translation"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159051003729.407106.10610703877543955831.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
gdbstub shouldn't silently change guest visible state when doing address
translation. Since the R/C bits can only be updated when handling a MMU
fault, let's reuse the cause_excp flag and rename it to guest_visible.
While here drop a not very useful comment.
This was found while reading the code. I could verify that this affects
both powernv and pseries, but I failed to observe any actual bug.
Fixes: d04ea940c5 "target/ppc: Add support for Radix partition-scoped translation"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941063899.240484.2778628492106387793.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last two arguments have the bool type. Also, we shouldn't raise an
exception when using gdbstub.
This was found while reading the code. Since it only affects the powernv
machine, I didn't dig further to find an actual bug.
Fixes: d04ea940c5 "target/ppc: Add support for Radix partition-scoped translation"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941063281.240484.9114539141307005992.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As per CODING_STYLE.
Fixes: d04ea940c5 "target/ppc: Add support for Radix partition-scoped translation"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941062665.240484.2663106458734800894.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is the job of the ppc_radix64_get_fully_qualified_addr() function
which is called at the beginning of ppc_radix64_xlate() to set both
lpid *and* pid. It doesn't buy us anything to initialize them first.
Worse, a bug in ppc_radix64_get_fully_qualified_addr(), eg. failing to
set either lpid or pid, would be undetectable by static analysis tools
like coverity.
Some recent versions of gcc (eg. gcc-9.3.1-2.fc30) may still think
that lpid or pid is used uninitialized though, so this also adds
default cases in the switch statements to make it clear this cannot
happen.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941062048.240484.9693581559252337111.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This doesn't require write access to the CPU registers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941061434.240484.10700096396035994133.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This doesn't require write access to the CPU structure.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941060817.240484.14621015211317485106.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On reboot, all memory that was previously added using object_add and
device_add is placed in this DIMM area.
The new SPAPR_LMB_FLAGS_HOTREMOVABLE flag helps Linux to put this memory in
the correct memory zone, so no unmovable allocations are made there,
allowing the object to be easily hot-removed by device_del and
object_del.
This new flag was accepted in Power Architecture documentation.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Bharata B Rao <bharata@linux.ibm.com>
Message-Id: <20200511200201.58537-1-leobras.c@gmail.com>
[dwg: Fixed syntax error spotted by Cédric Le Goater]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
POWER9 adds scv and rfscv instructions and the system call vectored
interrupt. Linux does not support this instruction yet but it has
been tested with a modified kernel that runs on real hardware.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20200507115328.789175-1-npiggin@gmail.com>
[dwg: Corrected an overlong line]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some tabs crept in with a recent change.
Fixes: 6dc6b55791 "target/ppc: Improve syscall exception logging"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158886788307.1560068.14096740175576278978.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Using the MSR instruction to write to CPSR.E is deprecated, but it is
required to work from any mode including unprivileged code. We were
incorrectly forbidding usermode code from writing it because
CPSR_USER did not include the CPSR_E bit.
We use CPSR_USER in only three places:
* as the mask of what to allow userspace MSR to write to CPSR
* when deciding what bits a linux-user signal-return should be
able to write from the sigcontext structure
* in target_user_copy_regs() when we set up the initial
registers for the linux-user process
In the first two cases not being able to update CPSR.E is a bug, and
in the third case it doesn't matter because CPSR.E is always 0 there.
So we can fix both bugs by adding CPSR_E to CPSR_USER.
Because the cpsr_write() in restore_sigcontext() is now changing
a CPSR bit which is cached in hflags, we need to add an
arm_rebuild_hflags() call there; the callsite in
target_user_copy_regs() was already rebuilding hflags for other
reasons.
(The recommended way to change CPSR.E is to use the 'SETEND'
instruction, which we do correctly allow from usermode code.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200518142801.20503-1-peter.maydell@linaro.org
Do not explicitly store zero to the NEON high part
when we can pass !is_q to clear_vec_high.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200519212453.28494-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 8-byte store for the end a !is_q operation can be
merged with the other stores. Use a no-op vector move
to trigger the expand_clr portion of tcg_gen_gvec_mov.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200519212453.28494-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GEN_NEON_INTEGER_OP macro is no longer used; remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Replace the float64 compare specializations with inline functions
that call the standard float64_compare{,_quiet} functions.
Use bool as the return type.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Give the previously unnamed enum a typedef name. Use it in the
prototypes of compare functions. Use it to hold the results
of the compare functions.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Give the previously unnamed enum a typedef name. Use the packed
attribute so that we do not affect the layout of the float_status
struct. Use it in the prototypes of relevant functions.
Adjust switch statements as necessary to avoid compiler warnings.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have had this on the to-do list for quite some time.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We cannot at present limit a 64-bit guest to a virtual address
space smaller than the host. It will mostly work to ignore this
limitation, except if the guest uses high bits of the address
space for tags. But it will certainly work better, as presently
we can wind up failing to allocate the guest stack.
Widen our user-only page tree to the host or abi pointer width.
Remove the workaround for this problem from target/alpha.
Always validate guest addresses vs reserved_va, as there we
control allocation ourselves.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20200513175134.19619-7-alex.bennee@linaro.org>
The CPU() macro is defined as:
#define CPU(obj) ((CPUState *)(obj))
which expands to:
((CPUState *)object_dynamic_cast_assert((Object *)(obj), (name),
__FILE__, __LINE__, __func__))
This assertion can only fail when @obj points to something other
than its stated type, i.e. when we're in undefined behavior country.
Remove the unnecessary CPU() casts when we already know the pointer
is of CPUState type.
Patch created mechanically using spatch with this script:
@@
typedef CPUState;
CPUState *s;
@@
- CPU(s)
+ s
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-2-f4bug@amsat.org>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
Both s390_features[S390_FEAT_PCC_CMAC_AES_256].name and
s390_features[S390_FEAT_PCC_CMAC_EAES_256].name is
"pcc-cmac-eaes-256". The former is obviously a pasto.
Impact:
* s390_feat_bitmap_to_ascii() misidentifies S390_FEAT_PCC_CMAC_AES_256
as "pcc-cmac-eaes-256". Affects QMP commands query-cpu-definitions,
query-cpu-model-expansion, query-cpu-model-baseline,
query-cpu-model-comparison, and the error message when
s390_realize_cpu_model() fails in check_compatibility().
* s390_cpu_list() also misidentifies it. Affects -cpu help.
* s390_cpu_model_register_props() creates CPU property
"pcc-cmac-eaes-256" twice. The second one fails, but the error is
ignored (a later commit will change that). Results in a single
property "pcc-cmac-eaes-256" with the description for
S390_FEAT_PCC_CMAC_AES_256, and no property for
S390_FEAT_PCC_CMAC_EAES_256. CPU properties are visible in CLI -cpu
and -device, QMP & HMP device_add, QMP device-list-properties, and
QOM introspection.
The two features are almost always used via their group msa4. Such
use is not affected by this bug.
Fix by deleting the wayward 'e'.
Fixes: 7824174462 ("s390x/cpumodel: introduce CPU features")
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: David Hildenbrand <david@redhat.com>
Cc: qemu-s390x@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20200505152926.18877-10-armbru@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[Lost paragraph in commit message restored, Fixes: tweaked]
object_property_set_description() and
object_class_property_set_description() fail only when property @name
is not found.
There are 85 calls of object_property_set_description() and
object_class_property_set_description(). None of them can fail:
* 84 immediately follow the creation of the property.
* The one in spapr_rng_instance_init() refers to a property created in
spapr_rng_class_init(), from spapr_rng_properties[].
Every one of them still gets to decide what to pass for @errp.
51 calls pass &error_abort, 32 calls pass NULL, one receives the error
and propagates it to &error_abort, and one propagates it to
&error_fatal. I'm actually surprised none of them violates the Error
API.
What are we gaining by letting callers handle the "property not found"
error? Use when the property is not known to exist is simpler: you
don't have to guard the call with a check. We haven't found such a
use in 5+ years. Until we do, let's make life a bit simpler and drop
the @errp parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-8-armbru@redhat.com>
[One semantic rebase conflict resolved]
Convert the Neon floating point VFMA and VFMS insn to decodetree.
These are the last insns in the 3-reg-same group so we can
remove all the support/loop code from the old decoder.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-18-peter.maydell@linaro.org
Convert the Neon fp VMAX/VMIN/VMAXNM/VMINNM/VRECPS/VRSQRTS 3-reg-same
insns to decodetree. (These are all the remaining non-accumulation
instructions in this group.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-17-peter.maydell@linaro.org
The usual location for the env argument in the argument list of a TCG helper
is immediately after the return-value argument. recps_f32 and rsqrts_f32
differ in that they put it at the end.
Move the env argument to its usual place; this will allow us to
more easily use these helper functions with the gvec APIs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-16-peter.maydell@linaro.org
Convert the Neon integer 3-reg-same compare insns VCGE, VCGT,
VCEQ, VACGE and VACGT to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-15-peter.maydell@linaro.org
Convert the Neon integer VMUL, VMLA, and VMLS 3-reg-same inssn to
decodetree.
We don't have a gvec helper for multiply-accumulate, so VMLA and VMLS
need a loop function do_3same_fp(). This takes a reads_vd parameter
to do_3same_fp() which tells it to load the old value into vd before
calling the callback function, in the same way that the do_vfp_3op_sp()
and do_vfp_3op_dp() functions in translate-vfp.inc.c work. (The
only uses in this patch pass reads_vd == true, but later commits
will use reads_vd == false.)
This conversion fixes in passing an underdecoding for VMUL
(originally reported by Fredrik Strupe <fredrik@strupe.net>): bit 1
of the 'size' field must be 0. The old decoder didn't enforce this,
but the decodetree pattern does.
The gen_VMLA_fp_reg() function performs the addition operation
with the operands in the opposite order to the old decoder:
since Neon sets 'default NaN mode' float32_add operations are
commutative so there is no behaviour difference, but putting
them this way around matches the Arm ARM pseudocode and the
required operation order for the subtraction in gen_VMLS_fp_reg().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-14-peter.maydell@linaro.org
Convert the Neon float VPMIN, VPMAX and VPADD 3-reg-same insns to
decodetree. These are the only remaining 'pairwise' operations,
so we can delete the pairwise-specific bits of the old decoder's
for-each-element loop now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-13-peter.maydell@linaro.org
Convert the Neon VADD, VSUB, VABD 3-reg-same insns to decodetree.
We already have gvec helpers for addition and subtraction, but must
add one for fabd.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-12-peter.maydell@linaro.org
Convert the Neon VQDMULH and VQRDMULH 3-reg-same insns to
decodetree. These are the last integer operations in the
3-reg-same group.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-11-peter.maydell@linaro.org
Convert the Neon integer VPADD 3-reg-same insns to decodetree. These
are 'pairwise' operations. (Note that VQRDMLAH, which shares the
same primary opcode but has U=1, has already been converted.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-10-peter.maydell@linaro.org
Convert the Neon integer VPMAX and VPMIN 3-reg-same insns to
decodetree. These are 'pairwise' operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-9-peter.maydell@linaro.org
Convert the VQSHL, VRSHL and VQRSHL insns in the 3-reg-same
group to decodetree. We have already implemented the size==0b11
case of these insns; this commit handles the remaining sizes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-8-peter.maydell@linaro.org
Convert the Neon VRHADD and VHSUB 3-reg-same insns to decodetree.
(These are all the other insns in 3-reg-same which were using
GEN_NEON_INTEGER_OP() and which are not pairwise or
reversed-operands.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-7-peter.maydell@linaro.org
Convert the Neon VABA and VABD insns in the 3-reg-same group to
decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-6-peter.maydell@linaro.org
Convert the Neon VHADD insns in the 3-reg-same group to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-5-peter.maydell@linaro.org
Convert the 64-bit element insns in the 3-reg-same group
to decodetree. This covers VQSHL, VRSHL and VQRSHL where
size==0b11.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-4-peter.maydell@linaro.org
Convert the Neon SHA instructions in the 3-reg-same group
to decodetree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-3-peter.maydell@linaro.org
Convert the Neon VQRDMLAH and VQRDMLSH insns in the 3-reg-same group
to decodetree. These don't use do_3same() because they want to
operate on VFP double registers, whose offsets are different from the
neon_reg_offset() calculations do_3same does.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200512163904.10918-2-peter.maydell@linaro.org
Add a SIGBUS signal handler. In this handler, it checks the SIGBUS type,
translates the host VA delivered by host to guest PA, then fills this PA
to guest APEI GHES memory, then notifies guest according to the SIGBUS
type.
When guest accesses the poisoned memory, it will generate a Synchronous
External Abort(SEA). Then host kernel gets an APEI notification and calls
memory_failure() to unmapped the affected page in stage 2, finally
returns to guest.
Guest continues to access the PG_hwpoison page, it will trap to KVM as
stage2 fault, then a SIGBUS_MCEERR_AR synchronous signal is delivered to
Qemu, Qemu records this error address into guest APEI GHES memory and
notifes guest using Synchronous-External-Abort(SEA).
In order to inject a vSEA, we introduce the kvm_inject_arm_sea() function
in which we can setup the type of exception and the syndrome information.
When switching to guest, the target vcpu will jump to the synchronous
external abort vector table entry.
The ESR_ELx.DFSC is set to synchronous external abort(0x10), and the
ESR_ELx.FnV is set to not valid(0x1), which will tell guest that FAR is
not valid and hold an UNKNOWN value. These values will be set to KVM
register structures through KVM_SET_ONE_REG IOCTL.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200512030609.19593-10-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm_hwpoison_page_add() and kvm_unpoison_all() will both
be used by X86 and ARM platforms, so moving them into
"accel/kvm/kvm-all.c" to avoid duplicate code.
For architectures that don't use the poison-list functionality
the reset handler will harmlessly do nothing, so let's register
the kvm_unpoison_all() function in the generic kvm_init() function.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Acked-by: Xiang Zheng <zhengxiang9@huawei.com>
Message-id: 20200512030609.19593-8-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Include 64-bit element size in preparation for SVE2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Include 64-bit element size in preparation for SVE2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Must clear the tail for AdvSIMD when SVE is enabled.
Fixes: ca40a6e6e3
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pass a pointer directly to env->vfp.qc[0], rather than env.
This will allow SVE2, which does not modify QC, to pass a
pointer to dummy storage.
Change the return type of inl_qrdml.h_s16 to match the
sense of the operation: signed.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-14-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a functional interface for the vector expansion.
This fits better with the existing set of helpers that
we provide for other operations.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These operations do not touch fp_status.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a functional interface for the vector expansion.
This fits better with the existing set of helpers that
we provide for other operations.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a functional interface for the vector expansion.
This fits better with the existing set of helpers that
we provide for other operations.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than perform the argument swap during code generation,
perform it during decode. This means it doesn't have to be
special cased later, and we can share code with aarch64 code
generation. Hopefully the decode comment addresses any confusion
that might arise in between.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a functional interface for the vector expansion.
This fits better with the existing set of helpers that
we provide for other operations.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a functional interface for the vector expansion.
This fits better with the existing set of helpers that
we provide for other operations.
Macro-ize the 5 nearly identical comparisons.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we've converted all cases to gvec, there is quite a bit
of dead code at the end of the function. Remove it.
Sink the call to gen_gvec_fn2i to the end, loading a function
pointer within the switch statement.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200513163245.17915-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
