The endianness of data exchange between tx and rx fifo is incorrect.
Earlier bytes are supposed to show up on MSB and later bytes on LSB,
ie: in big endian. The manual does not explicitly say this, but the
U-Boot and Linux driver codes have a swap on the data transferred
to tx fifo and from rx fifo.
With this change, U-Boot read from / write to SPI flash tests pass.
=> sf test 1ff000 1000
SPI flash test:
0 erase: 0 ticks, 4096000 KiB/s 32768.000 Mbps
1 check: 3 ticks, 1333 KiB/s 10.664 Mbps
2 write: 235 ticks, 17 KiB/s 0.136 Mbps
3 read: 2 ticks, 2000 KiB/s 16.000 Mbps
Test passed
0 erase: 0 ticks, 4096000 KiB/s 32768.000 Mbps
1 check: 3 ticks, 1333 KiB/s 10.664 Mbps
2 write: 235 ticks, 17 KiB/s 0.136 Mbps
3 read: 2 ticks, 2000 KiB/s 16.000 Mbps
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-11-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the ECSPIx_CONREG register BURST_LENGTH field, the manual says:
0x020 A SPI burst contains the 1 LSB in first word and all 32 bits in second word.
0x021 A SPI burst contains the 2 LSB in first word and all 32 bits in second word.
Current logic uses either s->burst_length or 32, whichever smaller,
to determine how many bits it should read from the tx fifo each time.
For example, for a 48 bit burst length, current logic transfers the
first 32 bit from the first word in the tx fifo, followed by a 16
bit from the second word in the tx fifo, which is wrong. The correct
logic should be: transfer the first 16 bit from the first word in
the tx fifo, followed by a 32 bit from the second word in the tx fifo.
With this change, SPI flash can be successfully probed by U-Boot on
imx6 sabrelite board.
=> sf probe
SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-10-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current implementation of the imx spi controller expects the burst
length to be multiple of 8, which is the most common use case.
In case the burst length is not what we expect, log it to give user
a chance to notice it, and round it up to be multiple of 8.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-9-bmeng.cn@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a write to ECSPI_CONREG register to disable the SPI controller,
imx_spi_soft_reset() is called to reset the controller, but chip
select lines should have been disabled, otherwise the state machine
of any devices (e.g.: SPI flashes) connected to the SPI master is
stuck to its last state and responds incorrectly to any follow-up
commands.
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-8-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, only the ECSPI_CONREG register can
be modified. Setting the EN bit enabled the device, clearing it
"disables the block and resets the internal logic with the
exception of the ECSPI_CONREG" register.
Ignore all other registers write except ECSPI_CONREG when the
block is disabled.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-7-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-6-f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, it stay it is 'internal reset logic'
(internal clocks are gated off). Reading any register returns
its reset value. Only update this value if the device is enabled.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-6-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-5-f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, all registers are reset with the
exception of the ECSPI_CONREG. It is initialized to zero
when the instance is created.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-5-bmeng.cn@gmail.com
[bmeng: add a 'common_reset' function that does most of reset operation]
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'burst_length' is cleared in imx_spi_reset(), which is called
after imx_spi_realize(). Remove the initialization to simplify.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-4-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-3-f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Usually the approach is that the device on the other end of the line
is going to reset its state anyway, so there's no need to actively
signal an irq line change during the reset hook.
Move imx_spi_update_irq() out of imx_spi_reset(), to a new function
imx_spi_soft_reset() that is called when the controller is disabled.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid using a magic number (4) everywhere for the number of chip
selects supported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 20210129132323.30946-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 5FA280F5.8060902@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ssi_auto_connect_slaves(parent, cs_line, bus) iterates over @parent's
QOM children @dev of type TYPE_SSI_SLAVE. It puts these on @bus, and
sets cs_line[] to qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0).
Suspicious: there is no protection against overrunning cs_line[].
Turns out it's safe because ssi_auto_connect_slaves() never finds any
such children. Its called by realize methods of some (but not all)
devices providing an SSI bus, and gets passed the device.
SSI slave devices are always created with ssi_create_slave_no_init(),
optionally via ssi_create_slave(). This adds them to their SSI bus.
It doesn't set their QOM parent.
ssi_create_slave_no_init() is always immediately followed by
qdev_init_nofail(), with no QOM parent assigned, so
device_set_realized() puts the device into the /machine/unattached/
orphanage. None become QOM children of a device providing an SSI bus.
ssi_auto_connect_slaves() was added in commit b4ae3cfa57 "ssi: Add
slave autoconnect helper". I can't see which slaves it was supposed
to connect back then.
Cc: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-23-armbru@redhat.com>
When inserting the value retrieved (rx) from the spi slave, rx is pushed to
rx_fifo after being cast to uint8_t. rx_fifo is a fifo32, and the rx
register the driver uses is also 32 bit. This zeroes the 24 most
significant bits of rx. This proved problematic with devices that expect to
use the whole 32 bits of the rx register.
Signed-off-by: Eden Mikitas <e.mikitas@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The while statement in question only checked if tx_burst is not 0.
tx_burst is a signed int, which is assigned the value put by the
guest driver in ECSPI_CONREG. The burst length can be anywhere
between 1 and 4096, and since tx_burst is always decremented by 8
it could possibly underflow, causing an infinite loop.
Signed-off-by: Eden Mikitas <e.mikitas@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The current emulation will clear the XCH bit when a burst finishes.
This is not quite correct. According to the i.MX7d referemce manual,
Rev 0.1, §10.1.7.3:
This bit [XCH] is cleared automatically when all data in the TXFIFO
and the shift register has been shifted out.
So XCH should be cleared when the FIFO empties, not on completion of a
burst. The FIFO is 64 x 32 bits = 2048 bits, while the max burst size
is larger at 4096 bits. So it's possible that the burst is not finished
after the TXFIFO empties.
Sending a large block (> 2048 bits) with the Linux driver will use a
burst that is larger than the TXFIFO. After the TXFIFO has emptied XCH
does not become unset, as the burst is not yet finished.
What should happen after the TXFIFO empties is the driver will refill it
and set XCH. The rising edge of XCH will trigger another transfer to
begin. However, since the emulation does not set XCH to 0, there is no
rising edge and the next trasfer never begins.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180731201056.29257-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the documentation it is not clear what this SPI register is about.
Moreover, neither linux driver nor xvisor driver are using this SPI register.
For now we just remove it and issue a log on register write access.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20170107122047.26300-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'char const' means the same thing as 'const char', but we
use the former in only a handful of places and we use the
latter over six thousand times. Switch the imx reg_name()
functions to bring them in line with everything else.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
