Each DRC has three fields describing its state: isolation_state,
allocation_state and configured. At first this seems like a reasonable
representation, since its based directly on the PAPR defined
isolation-state and allocation-state indicators. However:
* Only a few combinations of the two fields' values are permitted
* allocation_state isn't used at all for physical DRCs
* The indicators are write only so they don't really have a well
defined current value independent of each other
This replaces these variables with a single state variable, whose names
and numbers are based on the diagram in LoPAPR section 13.4. Along with
this we add code to check the current state on various operations and make
sure the requested transition is permitted.
Strictly speaking, this makes guest visible changes to behaviour (since we
probably allowed some transitions we shouldn't have before). However, a
hypothetical guest broken by that wasn't PAPR compliant, and probably
wouldn't have worked under PowerVM.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel Barboza <danielhb@linux.vnet.ibm.com>
Tested-by: Daniel Barboza <danielhb@linux.vnet.ibm.com>
There are 3 types of "indicator" associated with hotplug in the PAPR spec
the "allocation state", "isolation state" and "DR-indicator". The first
two are intimately tied to the various state transitions associated with
hotplug. The DR-indicator, however, is different and simpler.
It's basically just a guest controlled variable which can be used by the
guest to flag state or problems associated with a device. The idea is that
the hypervisor can use it to present information back on management
consoles (on some machines with PowerVM it may even control physical LEDs
on the machine case associated with the relevant device).
For that reason, there's only ever likely to be a single update
implementation so the set_indicator_state method isn't useful. Replace it
with a direct function call.
While we're there, make some small associated cleanups:
* PAPR doesn't use the term "indicator state", just "DR-indicator" and
the allocation state and isolation state are also considered "indicators".
Rename things to be less confusing
* Fold set_indicator_state() and rtas_set_indicator_state() into a single
rtas_set_dr_indicator() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Michael Roth <mdroth@linux.vnet.ibm.com>
In theory the RTAS set-indicator call can be used for a number of
"indicators" defined by PAPR. In practice the only ones we're ever likely
to implement are those used for Dynamic Reconfiguration (i.e. hotplug).
Because of this, the current implementation determines the associated DRC
object, before dispatching based on the type of indicator.
However, this means we also need a check that we're dealing with a DR
related indicator at all, which duplicates some of the logic from the
switch further down.
Even though it means a bit of code duplication, things work out cleaner if
we delegate the DRC lookup to the individual indicator type functions -
and it also allows some further cleanups.
While we're there, remove references to "sensor", a copy/paste artefact
from the related, but distinct "get-sensor" call.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Michael Roth <mdroth@linux.vnet.ibm.com>
DRC classes have an entity_sense method to determine (in a specific PAPR
sense) the presence or absence of a device plugged into a DRC. However,
we only have one implementation of the method, which explicitly tests for
different DRC types. This changes it to instead have different method
implementations for the two cases: "logical" and "physical" DRCs.
While we're at it, the entity sense method always returns RTAS_OUT_SUCCESS,
and the interesting value is returned via pass-by-reference. Simplify this
to directly return the value we care about
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Michael Roth <mdroth@linux.vnet.ibm.com>
During boot, PAPR guests negotiate CPU model support with the
ibm,client-architecture-support mechanism. The logic to implement this in
qemu is very convoluted. This cleans it up to be cleaner, using the new
ppc_check_compat() call.
The new logic for choosing a compatibility mode is:
1. Usually, use the most recent compatibility mode that is
a) supported by the guest
b) supported by the CPU
and c) no later than the maximum allowed (if specified)
2. If no suitable compatibility mode was found, the guest *does*
support this CPU explicitly, and no maximum compatibility mode is
specified, then use "raw" mode for the current CPU
3. Otherwise, fail the boot.
This differs from the results of the old code: the old code preferred using
"raw" mode to a compatibility mode, whereas the new code prefers a
compatibility mode if available. Using compatibility mode preferentially
means that we're more likely to be able to migrate the guest to a similar
but not identical host.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added CONFIG_RS6000_MC to ppc64 or it breaks testcases]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This device is a partial duplicate of System I/O device available in hw/ppc/prep.c
This new one doesn't have all the Motorola-specific registers.
The old one should be deprecated and removed with the 'prep' machine.
Partial documentation available at
ftp://ftp.software.ibm.com/rs6000/technology/spec/srp1_1.exe
section 6.1.5 (I/O Device Mapping)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds support for Dynamic DMA Windows (DDW) option defined by
the SPAPR specification which allows to have additional DMA window(s)
The "ddw" property is enabled by default on a PHB but for compatibility
the pseries-2.6 machine and older disable it.
This also creates a single DMA window for the older machines to
maintain backward migration.
This implements DDW for PHB with emulated and VFIO devices. The host
kernel support is required. The advertised IOMMU page sizes are 4K and
64K; 16M pages are supported but not advertised by default, in order to
enable them, the user has to specify "pgsz" property for PHB and
enable huge pages for RAM.
The existing linux guests try creating one additional huge DMA window
with 64K or 16MB pages and map the entire guest RAM to. If succeeded,
the guest switches to dma_direct_ops and never calls TCE hypercalls
(H_PUT_TCE,...) again. This enables VFIO devices to use the entire RAM
and not waste time on map/unmap later. This adds a "dma64_win_addr"
property which is a bus address for the 64bit window and by default
set to 0x800.0000.0000.0000 as this is what the modern POWER8 hardware
uses and this allows having emulated and VFIO devices on the same bus.
This adds 4 RTAS handlers:
* ibm,query-pe-dma-window
* ibm,create-pe-dma-window
* ibm,remove-pe-dma-window
* ibm,reset-pe-dma-window
These are registered from type_init() callback.
These RTAS handlers are implemented in a separate file to avoid polluting
spapr_iommu.c with PCI.
This changes sPAPRPHBState::dma_liobn to an array to allow 2 LIOBNs
and updates all references to dma_liobn. However this does not add
64bit LIOBN to the migration stream as in fact even 32bit LIOBN is
rather pointless there (as it is a PHB property and the management
software can/should pass LIOBNs via CLI) but we keep it for the backward
migration support.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move all trace-events for files in the hw/ppc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1466066426-16657-27-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
David Gibson