We currently miss a bunch of register resets in the device reset
function. This sometimes prevents the guest from rebooting after
a system_reset (with virtio-blk-pci). For instance, we may get
the following errors:
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid read at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid write at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220202111602.627429-1-eric.auger@redhat.com
Fixes: 10a83cb988 ("hw/arm/smmuv3: Skeleton")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Always call arm_load_kernel() regardless of kernel_filename being
set. This is needed because arm_load_kernel() sets up reset for
the CPUs.
Fixes: 6f16da53ff (hw/arm: versal: Add a virtual Xilinx Versal board)
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220130110313.4045351-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're using PSCI emulation, we add a /psci node to the device tree
we pass to the guest. At the moment, if the dtb already has a /psci
node in it, we retain it, rather than replacing it. (This behaviour
was added in commit c39770cd63 in 2018.)
This is a problem if the existing node doesn't match our PSCI
emulation. In particular, it might specify the wrong method (HVC vs
SMC), or wrong function IDs for cpu_suspend/cpu_off/etc, in which
case the guest will not get the behaviour it wants when it makes PSCI
calls.
An example of this is trying to boot the highbank or midway board
models using the device tree supplied in the kernel sources: this
device tree includes a /psci node that specifies function IDs that
don't match the (PSCI 0.2 compliant) IDs that QEMU uses. The dtb
cpu_suspend function ID happens to match the PSCI 0.2 cpu_off ID, so
the guest hangs after booting when the kernel tries to idle the CPU
and instead it gets turned off.
Instead of retaining an existing /psci node, delete it entirely
and replace it with a node whose properties match QEMU's PSCI
emulation behaviour. This matches the way we handle /memory nodes,
where we also delete any existing nodes and write in ones that
match the way QEMU is going to behave.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-17-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
The highbank and midway board code includes boot-stub code for
handling secondary CPU boot which keeps the secondaries in a pen
until the primary writes to a known location with the address they
should jump to.
This code is never used, because the boards enable QEMU's PSCI
emulation, so secondary CPUs are kept powered off until the PSCI call
which turns them on, and then start execution from the address given
by the guest in that PSCI call. Delete the unreachable code.
(The code was wrong for midway in any case -- on the Cortex-A15 the
GIC CPU interface registers are at a different offset from PERIPHBASE
compared to the Cortex-A9, and the code baked-in the offsets for
highbank's A9.)
Note that this commit implicitly depends on the preceding "Don't
write secondary boot stub if using PSCI" commit -- the default
secondary-boot stub code overlaps with one of the highbank-specific
bootcode rom blobs, so we must suppress the secondary-boot
stub code entirely, not merely replace the highbank-specific
version with the default.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-15-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Now that we have dealt with the one special case (highbank) that needed
to set both psci_conduit and secure_board_setup, we don't need to
allow that combination any more. It doesn't make sense in general,
so use an assertion to ensure we don't add new boards that do it
by accident without thinking through the consequences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-13-peter.maydell@linaro.org
Guest code on highbank may make non-PSCI SMC calls in order to
enable/disable the L2x0 cache controller (see the Linux kernel's
arch/arm/mach-highbank/highbank.c highbank_l2c310_write_sec()
function). The ABI for this is documented in kernel commit
8e56130dcb as being borrowed from the OMAP44xx ROM. The OMAP44xx TRM
documents this function ID as having no return value and potentially
trashing all guest registers except SP and PC. For QEMU's purposes
(where our L2x0 model is a stub and enabling or disabling it doesn't
affect the guest behaviour) a simple "do nothing" SMC is fine.
We currently implement this NOP behaviour using a little bit of
Secure code we run before jumping to the guest kernel, which is
written by arm_write_secure_board_setup_dummy_smc(). The code sets
up a set of Secure vectors where the SMC entry point returns without
doing anything.
Now that the PSCI SMC emulation handles all SMC calls (setting r0 to
an error code if the input r0 function identifier is not recognized),
we can use that default behaviour as sufficient for the highbank
cache controller call. (Because the guest code assumes r0 has no
interesting value on exit it doesn't matter that we set it to the
error code). We can therefore delete the highbank board code that
sets secure_board_setup to true and writes the secure-code bootstub.
(Note that because the OMAP44xx ABI puts function-identifiers in
r12 and PSCI uses r0, we only avoid a clash because Linux's code
happens to put the function-identifier in both registers. But this
is true also when the kernel is running on real firmware that
implements both ABIs as far as I can see.)
This change fixes in passing booting on the 'midway' board model,
which has been completely broken since we added support for Hyp
mode to the Cortex-A15 CPU. When we did that boot.c was made to
start running the guest code in Hyp mode; this includes the
board_setup hook, which instantly UNDEFs because the NSACR is
not accessible from Hyp. (Put another way, we never made the
secure_board_setup hook support cope with Hyp mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-12-peter.maydell@linaro.org
Change the highbank/midway boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit and start-powered-off
properties on the CPU objects in the board code, and instead set the
psci_conduit field in the arm_boot_info struct to tell the common
boot loader code that we'd like PSCI if the guest is starting at an
EL that it makes sense with (in which case it will set these
properties).
This means that when running guest code at EL3, all the cores
will start execution at once on poweron. This matches the
real hardware behaviour. (A brief description of the hardware
boot process is in the u-boot documentation for these boards:
https://u-boot.readthedocs.io/en/latest/board/highbank/highbank.html#boot-process
-- in theory one might run the 'a9boot'/'a15boot' secure monitor
code in QEMU, though we probably don't emulate enough for that.)
This affects the highbank and midway boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-10-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the virt board code, set the arm_boot_info psci_conduit
field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel or to the generic loader. (EL3 guest code started
via -bios or -pflash was already being run with PSCI emulation
disabled.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-9-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Change the Xilinx ZynqMP-based board xlnx-zcu102 to use the new
boot.c functionality to allow us to enable psci-conduit only if
the guest is being booted in EL1 or EL2, so that if the user runs
guest EL3 firmware code our PSCI emulation doesn't get in its
way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
Note that this means that EL3 guest code will have no way
to power on secondary cores, because we don't model any
kind of power controller that does that on this SoC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-7-peter.maydell@linaro.org
Change the allwinner-h3 based board to use the new boot.c
functionality to allow us to enable psci-conduit only if the guest is
being booted in EL1 or EL2, so that if the user runs guest EL3
firmware code our PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes sense
with.
This affects the orangepi-pc board.
This commit leaves the secondary CPUs in the powered-down state if
the guest is booting at EL3, which is the same behaviour as before
this commit. The secondaries can no longer be started by that EL3
code making a PSCI call but can still be started via the CPU
Configuration Module registers (which we model in
hw/misc/allwinner-cpucfg.c).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-6-peter.maydell@linaro.org
Change the iMX-SoC based boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
This affects the mcimx6ul-evk and mcimx7d-sabre boards.
Note that for the mcimx7d board, this means that when running guest
code at EL3 there is currently no way to power on the secondary CPUs,
because we do not currently have a model of the system reset
controller module which should be used to do that for the imx7 SoC,
only for the imx6 SoC. (Previously EL3 code which knew it was
running on QEMU could use a PSCI call to do this.) This doesn't
affect the imx6ul-evk board because it is uniprocessor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-5-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Address should be 0x1E631000 and not 0x1E641000 as initially introduced.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/838
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Suggested-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220126083520.4135713-1-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect Micron Xccela mt35xu01g flashes to the OSPI flash memory
controller.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-10-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the OSPI flash memory controller model (including the source and
destination DMA).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-8-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an orgate and 'or' the interrupts from the BBRAM and RTC models.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-3-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In commit d5093d9615 we added a VMStateDescription to
the TYPE_ARMV7M object, to handle migration of its Clocks.
However a cut-and-paste error meant we used the wrong struct
name in the VMSTATE_CLOCK() macro arguments. The result was
that attempting a 'savevm' might result in an assertion
failure.
Cc: qemu-stable@nongnu.org
Buglink: https://gitlab.com/qemu-project/qemu/-/issues/803
Fixes: d5093d9615
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120151609.433555-1-peter.maydell@linaro.org
Now that the devices present in the extended memory map are checked
against the available PA space and disabled when they don't fit,
there is no need to keep the same checks against highmem, as
highmem really is a shortcut for the PA space being 32bit.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-id: 20220114140741.1358263-7-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to only keep the highmem devices that actually fit in
the PA range, check their location against the range and update
highest_gpa if they fit. If they don't, mark them as disabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-6-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The highmem attribute is nothing but another way to express the
PA range of a VM. To support HW that has a smaller PA range then
what QEMU assumes, pass this PA range to the virt_set_memmap()
function, allowing it to correctly exclude highmem devices
if they are outside of the PA range.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-5-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Even when the VM is configured with highmem=off, the highest_gpa
field includes devices that are above the 4GiB limit.
Similarily, nothing seem to check that the memory is within
the limit set by the highmem=off option.
This leads to failures in virt_kvm_type() on systems that have
a crippled IPA range, as the reported IPA space is larger than
what it should be.
Instead, honor the user-specified limit to only use the devices
at the lowest end of the spectrum, and fail if we have memory
crossing the 4GiB limit.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-id: 20220114140741.1358263-4-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe region
using highmem_ecam, let's add a control for the highmem GICv3
redistributor region.
Similarily to highmem_ecam, these redistributors are disabled when
highmem is off.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-3-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe ECAM
region using highmem_ecam, let's add a control for the highmem
PCIe MMIO region.
Similarily to highmem_ecam, this region is disabled when highmem
is off.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-2-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports virtio-mem-pci device on "virt" platform, by simply
following the implementation on x86.
* This implements the hotplug handlers to support virtio-mem-pci
device hot-add, while the hot-remove isn't supported as we have
on x86.
* The block size is 512MB on ARM64 instead of 128MB on x86.
* It has been passing the tests with various combinations like 64KB
and 4KB page sizes on host and guest, different memory device
backends like normal, transparent huge page and HugeTLB, plus
migration.
Co-developed-by: David Hildenbrand <david@redhat.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-id: 20220111063329.74447-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support one cluster level between core and physical package in the
cpu-map of Arm/virt devicetree. This is also consistent with Linux
Doc "Documentation/devicetree/bindings/cpu/cpu-topology.txt".
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220107083232.16256-3-wangyanan55@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM64 machines like Kunpeng Family Server Chips have a level
of hardware topology in which a group of CPU cores share L3
cache tag or L2 cache. For example, Kunpeng 920 typically
has 6 or 8 clusters in each NUMA node (also represent range
of CPU die), and each cluster has 4 CPU cores. All clusters
share L3 cache data, but CPU cores in each cluster share a
local L3 tag.
Running a guest kernel with Cluster-Aware Scheduling on the
Hosts which have physical clusters, if we can design a vCPU
topology with cluster level for guest kernel and then have
a dedicated vCPU pinning, the guest will gain scheduling
performance improvement from cache affinity of CPU cluster.
So let's enable the support for this new parameter on ARM
virt machines. After this patch, we can define a 4-level
CPU hierarchy like: cpus=*,maxcpus=*,sockets=*,clusters=*,
cores=*,threads=*.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220107083232.16256-2-wangyanan55@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 network device is hidden in the Musicpal
machine. Move it into a new unit file under the hw/net/ directory.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are going to move this code, so fix its style first to avoid:
ERROR: spaces required around that '/' (ctx:VxV)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 is a system-on-chip with an ARM core.
We implement its audio codecs and network interface.
Homogeneous SoC Kconfig are usually defined in the hw/$ARCH
directory. Move it there.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generally a guest needs an external source of randomness to properly
enable things like address space randomisation. However in a trusted
boot environment where the firmware will cryptographically verify
components having random data in the DTB will cause verification to
fail. Add a control knob so we can prevent this being added to the
system DTB.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20220105135009.1584676-22-alex.bennee@linaro.org>
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHY2zEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpCiEH/jv5tHUffDdGz5M2pN7FTWPQ9UAMQZXbn5AS
PPVutOI/B+ILYBuNjYLvMGeq6ymG4/0DM940/jkQwCWD4ku1OG0ReM5T5klUR8lY
df5y1SCDv3Yoq0vxpQCnssKqbgm8Kf9tnAFjni7Lvbu3oo6DCq77m6MWEapLoEUu
IkM+l60NKmHAClnE6RF4KobLa5srIlDTho1iBXH5S39CRF1LvP9NgnYzl7nqiEkq
ZYQEqkKO5XGxZji9banZPJD2kxt1iL7s24QI6OJG2Lz8Hf86b0Yo7XJpmw4ShP9h
Vl1SL3m/HhHSMBuXOb7w/EkCm59b7whXCmoyYBF/GqaxtZkvVnM=
=4VIN
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci,pc: features,fixes,cleanups
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 07 Jan 2022 04:30:41 PM PST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (55 commits)
tests: acpi: Add updated TPM related tables
acpi: tpm: Add missing device identification objects
tests: acpi: prepare for updated TPM related tables
virtio/vhost-vsock: don't double close vhostfd, remove redundant cleanup
hw/scsi/vhost-scsi: don't double close vhostfd on error
hw/scsi/vhost-scsi: don't leak vqs on error
docs: reSTify virtio-balloon-stats documentation and move to docs/interop
hw/i386/pc: Add missing property descriptions
acpihp: simplify acpi_pcihp_disable_root_bus
tests: acpi: SLIC: update expected blobs
tests: acpi: add SLIC table test
tests: acpi: whitelist expected blobs before changing them
acpi: fix QEMU crash when started with SLIC table
intel-iommu: correctly check passthrough during translation
virtio-mem: Set "unplugged-inaccessible=auto" for the 7.0 machine on x86
virtio-mem: Support VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
linux-headers: sync VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
MAINTAINERS: Add a separate entry for acpi/VIOT tables
virtio: signal after wrapping packed used_idx
virtio-mem: Support "prealloc=on" option
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add missing TPM device identification objects _STR and _UID. They will
appear as files 'description' and 'uid' under Linux sysfs.
Following inspection of sysfs entries for hardware TPMs we chose
uid '1'.
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/708
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Message-id: 20211223022310.575496-3-stefanb@linux.ibm.com
Message-Id: <20220104175806.872996-3-stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Add the four lm75s behind the mux on bus 13.
Tested by booting the firmware:
lm75 42-0048: hwmon0: sensor 'lm75'
lm75 43-0049: supply vs not found, using dummy regulator
lm75 43-0049: hwmon1: sensor 'lm75'
lm75 44-0048: supply vs not found, using dummy regulator
lm75 44-0048: hwmon2: sensor 'lm75'
lm75 45-0049: supply vs not found, using dummy regulator
lm75 45-0049: hwmon3: sensor 'lm75'
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220102215844.2888833-5-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AST2600 Display Port MCU introduces 0x18000000~0x1803FFFF as it's memory
and io address. If guest machine try to access DPMCU memory, it will
cause a fatal error.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20211210083034.726610-1-troy_lee@aspeedtech.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the enums to match the naming style used by QAPI, and to
use "32" and "64" instead of "20" and "31". This will allow us
to more easily move the enum to the QAPI schema later.
About the naming choice: "SMBIOS 2.1 entry point"/"SMBIOS 3.0
entry point" and "32-bit entry point"/"64-bit entry point" are
synonymous in the SMBIOS specification. However, the phrases
"32-bit entry point" and "64-bit entry point" are used more often.
The new names also avoid confusion between the entry point format
and the actual SMBIOS version reported in the entry point
structure. For example: currently the 32-bit entry point
actually report SMBIOS 2.8 support, not 2.1.
Based on portions of a patch submitted by Daniel P. Berrangé.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-2-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 7.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211217143948.289995-1-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
The aspeed machines connects backends with drive_get_next() in several
counting loops, one of them in a helper function, and a conditional.
Change it to use drive_get() directly. This makes the unit numbers
explicit in the code.
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-13-armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
