hvf_reset_vcpu() duplicates actions performed by x86_cpu_reset(). The
difference is that hvf_reset_vcpu() stores initial values directly to
VMCS while x86_cpu_reset() stores it in CPUX86State and then
cpu_synchronize_all_post_init() or cpu_synchronize_all_post_reset()
flushes CPUX86State into VMCS. That makes hvf_reset_vcpu() a kind of
no-op.
Here's the trace of CPU state modifications during VM start:
hvf_reset_vcpu (resets VMCS)
cpu_synchronize_all_post_init (overwrites VMCS fields written by
hvf_reset_vcpu())
cpu_synchronize_all_states
hvf_reset_vcpu (resets VMCS)
cpu_synchronize_all_post_reset (overwrites VMCS fields written by
hvf_reset_vcpu())
General purpose registers, system registers, segment descriptors, flags
and IP are set by hvf_put_segments() in post-init and post-reset,
therefore it's safe to remove them from hvf_reset_vcpu().
PDPTE initialization can be dropped because Intel SDM (26.3.1.6 Checks
on Guest Page-Directory-Pointer-Table Entries) doesn't require PDPTE to
be clear unless PAE is used: "A VM entry to a guest that does not use
PAE paging does not check the validity of any PDPTEs."
And if PAE is used, PDPTE's are initialized from CR3 in macvm_set_cr0().
Cc: Cameron Esfahani <dirty@apple.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200630102824.77604-8-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hvf lacks an implementation of cpu_synchronize_pre_loadvm().
Cc: Cameron Esfahani <dirty@apple.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200630102824.77604-4-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only remaining special case is postcopy. It cannot handle
concurrent discards yet, which would result in requesting already sent
pages from the source. Special-case it in virtio-balloon instead.
Introduce migration_in_incoming_postcopy(), to find out if incoming
postcopy is active.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drives with interface types other than if=none are for onboard
devices. Unfortunately, any such drives the board doesn't pick up can
still be used with -device, like this:
$ qemu-system-x86_64 -nodefaults -display none -S -drive if=floppy,id=bogus,unit=7 -device ide-cd,drive=bogus -monitor stdio
QEMU 5.0.50 monitor - type 'help' for more information
(qemu) info block
bogus: [not inserted]
Attached to: /machine/peripheral-anon/device[0]
Removable device: not locked, tray closed
(qemu) info qtree
bus: main-system-bus
type System
[...]
bus: ide.1
type IDE
dev: ide-cd, id ""
---> drive = "bogus"
[...]
unit = 0 (0x0)
[...]
This kind of abuse has always worked. Deprecate it:
qemu-system-x86_64: -drive if=floppy,id=bogus,unit=7: warning: bogus if=floppy is deprecated, use if=none
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-9-armbru@redhat.com>
We are going to split the TPM backends from the TPM emulated
hardware in the next commit. Make the TPM util helpers accessible
by moving local "tpm_util.h" to global "sysemu/tpm_util.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-id: 20200612085444.8362-12-philmd@redhat.com
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
They have no use.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20200528193758.51454-4-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They're either declared elsewhere or have no use.
While at it, rename _hvf_cpu_synchronize_post_init() to
do_hvf_cpu_synchronize_post_init().
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200528193758.51454-3-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
"sysemu/hvf.h" is intended for inclusion in generic code. However it
also contains several hvf definitions and declarations, including
HVFState that are used only inside "hvf.c". "hvf-i386.h" would be more
appropriate place to define HVFState as it's only included by "hvf.c"
and "x86_task.c".
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200528193758.51454-2-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When HVF is not available, the hvf_allowed variable does not exist.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200526172427.17460-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When TCG is not available, the tcg_allowed variable does not exist.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200526172427.17460-3-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Restrict init_machine(), setup_post() and has_memory()
to system-mode.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200526172427.17460-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is majorly only for X86 because that's the only one that supports
split irqchip for now.
When the irqchip is split, we face a dilemma that KVM irqfd will be
enabled, however the slow irqchip is still running in the userspace.
It means that the resamplefd in the kernel irqfds won't take any
effect and it will miss to ack INTx interrupts on EOIs.
One example is split irqchip with VFIO INTx, which will break if we
use the VFIO INTx fast path.
This patch can potentially supports the VFIO fast path again for INTx,
that the IRQ delivery will still use the fast path, while we don't
need to trap MMIOs in QEMU for the device to emulate the EIOs (see the
callers of vfio_eoi() hook). However the EOI of the INTx will still
need to be done from the userspace by caching all the resamplefds in
QEMU and kick properly for IOAPIC EOI broadcast.
This is tricky because in this case the userspace ioapic irr &
remote-irr will be bypassed. However such a change will greatly boost
performance for assigned devices using INTx irqs (TCP_RR boosts 46%
after this patch applied).
When the userspace is responsible for the resamplefd kickup, don't
register it on the kvm_irqfd anymore, because on newer kernels (after
commit 654f1f13ea56, 5.2+) the KVM_IRQFD will fail if with both split
irqchip and resamplefd. This will make sure that the fast path will
work for all supported kernels.
https://patchwork.kernel.org/patch/10738541/#22609933
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200318145204.74483-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This code is not related to hardware emulation.
Move it under accel/ with the other hypervisors.
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200508100222.7112-1-philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We use the Object type all over the place.
Forward declare it in "qemu/typedefs.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200504115656.6045-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a TPM2 ACPI table if a TPM2.0 sysbus device has been
dynamically instantiated.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200601095737.32671-4-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows us to keep pc-bios in executable_dir/pc-bios, rather than
executable_dir/../pc-bios, which is incompatible with oss-fuzz' file
structure.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20200512030133.29896-2-alxndr@bu.edu
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Two callers of BlockDriver.bdrv_make_empty() remain that should not call
this method directly. Both do not have access to a BdrvChild, but they
can use a BlockBackend, so we add this function that lets them use it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200429141126.85159-4-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
Add a SIGBUS signal handler. In this handler, it checks the SIGBUS type,
translates the host VA delivered by host to guest PA, then fills this PA
to guest APEI GHES memory, then notifies guest according to the SIGBUS
type.
When guest accesses the poisoned memory, it will generate a Synchronous
External Abort(SEA). Then host kernel gets an APEI notification and calls
memory_failure() to unmapped the affected page in stage 2, finally
returns to guest.
Guest continues to access the PG_hwpoison page, it will trap to KVM as
stage2 fault, then a SIGBUS_MCEERR_AR synchronous signal is delivered to
Qemu, Qemu records this error address into guest APEI GHES memory and
notifes guest using Synchronous-External-Abort(SEA).
In order to inject a vSEA, we introduce the kvm_inject_arm_sea() function
in which we can setup the type of exception and the syndrome information.
When switching to guest, the target vcpu will jump to the synchronous
external abort vector table entry.
The ESR_ELx.DFSC is set to synchronous external abort(0x10), and the
ESR_ELx.FnV is set to not valid(0x1), which will tell guest that FAR is
not valid and hold an UNKNOWN value. These values will be set to KVM
register structures through KVM_SET_ONE_REG IOCTL.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200512030609.19593-10-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm_hwpoison_page_add() and kvm_unpoison_all() will both
be used by X86 and ARM platforms, so moving them into
"accel/kvm/kvm-all.c" to avoid duplicate code.
For architectures that don't use the poison-list functionality
the reset handler will harmlessly do nothing, so let's register
the kvm_unpoison_all() function in the generic kvm_init() function.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Acked-by: Xiang Zheng <zhengxiang9@huawei.com>
Message-id: 20200512030609.19593-8-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are several callers that need to create a new block backend from
an existing BDS; make the task slightly easier with a common helper
routine.
Suggested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200424190903.522087-2-eblake@redhat.com>
[mreitz: Set @ret only in error paths, see
https://lists.nongnu.org/archive/html/qemu-block/2020-04/msg01216.html]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200428192648.749066-2-eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
- Fix resize (extending) of short overlays
- nvme: introduce PMR support from NVMe 1.4 spec
- qemu-storage-daemon: Fix non-string --object properties
-----BEGIN PGP SIGNATURE-----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=ad71
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix resize (extending) of short overlays
- nvme: introduce PMR support from NVMe 1.4 spec
- qemu-storage-daemon: Fix non-string --object properties
# gpg: Signature made Thu 30 Apr 2020 16:51:45 BST
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
qemu-storage-daemon: Fix non-string --object properties
qom: Factor out user_creatable_add_dict()
nvme: introduce PMR support from NVMe 1.4 spec
qcow2: Forward ZERO_WRITE flag for full preallocation
iotests: Test committing to short backing file
iotests: Filter testfiles out in filter_img_info()
block: truncate: Don't make backing file data visible
file-posix: Support BDRV_REQ_ZERO_WRITE for truncate
raw-format: Support BDRV_REQ_ZERO_WRITE for truncate
qcow2: Support BDRV_REQ_ZERO_WRITE for truncate
block-backend: Add flags to blk_truncate()
block: Add flags to bdrv(_co)_truncate()
block: Add flags to BlockDriver.bdrv_co_truncate()
qemu-iotests: allow qcow2 external discarded clusters to contain stale data
qcow2: Add incompatibility note between backing files and raw external data files
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that node level interface bdrv_truncate() supports passing request
flags to the block driver, expose this on the BlockBackend level, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200424125448.63318-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make compat in qemu_fdt_node_path() const char *.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200423121114.4274-3-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow name wildcards in qemu_fdt_node_path(). This is useful
to find all nodes with a given compatibility string.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200423121114.4274-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
External callers of blk_co_*() and of the synchronous blk_*() functions
don't currently increase the BlockBackend.in_flight counter, but calls
from blk_aio_*() do, so there is an inconsistency whether the counter
has been increased or not.
This patch moves the actual operations to static functions that can
later know they will always be called with in_flight increased exactly
once, even for external callers using the blk_co_*() coroutine
interfaces.
If the public blk_co_*() interface is unused, remove it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200407121259.21350-3-kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Squashed patches from Richard Henderson modifying
qapi/common.json and tests/machine-none-test.c]
Message-Id: <20200224141923.82118-21-ysato@users.sourceforge.jp>
[PMD: Added @since 5.0 tag in SysEmuTarget]
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently, TSC is set as part of the VM runtime state. Setting TSC at
runtime is heavy and additionally can have side effects on the guest,
which are not very resilient to variances in the TSC. This patch uses
the VM state to determine whether to set TSC or not. Some minor
enhancements for getting TSC values as well that considers the VM state.
Additionally, while setting the TSC, the partition is suspended to
reduce the variance in the TSC value across vCPUs.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <SN4PR2101MB08804D23439166E81FF151F7C0EA0@SN4PR2101MB0880.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Description copied from Linux kernel commit from Gustavo A. R. Silva
(see [3]):
--v-- description start --v--
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to
declare variable-length types such as these ones is a flexible
array member [1], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler
warning in case the flexible array does not occur last in the
structure, which will help us prevent some kind of undefined
behavior bugs from being unadvertenly introduced [2] to the
Linux codebase from now on.
--^-- description end --^--
Do the similar housekeeping in the QEMU codebase (which uses
C99 since commit 7be41675f7).
All these instances of code were found with the help of the
following Coccinelle script:
@@
identifier s, m, a;
type t, T;
@@
struct s {
...
t m;
- T a[0];
+ T a[];
};
@@
identifier s, m, a;
type t, T;
@@
struct s {
...
t m;
- T a[0];
+ T a[];
} QEMU_PACKED;
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=76497732932f
[3] https://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux.git/commit/?id=17642a2fbd2c1
Inspired-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-5-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
These days device-hotplug.c only contains the hmp_drive_add
In the next patch, rest of hmp_drive* functions will be moved
there.
Also add block-hmp-cmds.h to contain prototypes of these
functions
License for block-hmp-cmds.h since it contains the code
moved from sysemu.h which lacks license and thus according
to LICENSE is under GPLv2+
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200308092440.23564-4-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
blockdev.c uses the arch_type constant, so before we can use the file in
tools (i.e. outside of the system emulator), we need to add a stub for
it. A new QEMU_ARCH_NONE is introduced for this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-3-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduce the tpm-tis-device which is a sysbus device
and is bound to be used on ARM.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20200305165149.618-6-eric.auger@redhat.com
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
As we plan to introduce a sysbus TPM_TIS, let's rename
TPM_TIS into TPM_TIS_ISA.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20200305165149.618-2-eric.auger@redhat.com
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
This series removes ad hoc RAM allocation API (memory_region_allocate_system_memory)
and consolidates it around hostmem backend. It allows to
* resolve conflicts between global -mem-prealloc and hostmem's "policy" option,
fixing premature allocation before binding policy is applied
* simplify complicated memory allocation routines which had to deal with 2 ways
to allocate RAM.
* reuse hostmem backends of a choice for main RAM without adding extra CLI
options to duplicate hostmem features. A recent case was -mem-shared, to
enable vhost-user on targets that don't support hostmem backends [1] (ex: s390)
* move RAM allocation from individual boards into generic machine code and
provide them with prepared MemoryRegion.
* clean up deprecated NUMA features which were tied to the old API (see patches)
- "numa: remove deprecated -mem-path fallback to anonymous RAM"
- (POSTPONED, waiting on libvirt side) "forbid '-numa node,mem' for 5.0 and newer machine types"
- (POSTPONED) "numa: remove deprecated implicit RAM distribution between nodes"
Introduce a new machine.memory-backend property and wrapper code that aliases
global -mem-path and -mem-alloc into automatically created hostmem backend
properties (provided memory-backend was not set explicitly given by user).
A bulk of trivial patches then follow to incrementally convert individual
boards to using machine.memory-backend provided MemoryRegion.
Board conversion typically involves:
* providing MachineClass::default_ram_size and MachineClass::default_ram_id
so generic code could create default backend if user didn't explicitly provide
memory-backend or -m options
* dropping memory_region_allocate_system_memory() call
* using convenience MachineState::ram MemoryRegion, which points to MemoryRegion
allocated by ram-memdev
On top of that for some boards:
* missing ram_size checks are added (typically it were boards with fixed ram size)
* ram_size fixups are replaced by checks and hard errors, forcing user to
provide correct "-m" values instead of ignoring it and continuing running.
After all boards are converted, the old API is removed and memory allocation
routines are cleaned up.
The handler allows a qtest client to send commands to the server by
directly calling a function, rather than using a file/CharBackend
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20200220041118.23264-9-alxndr@bu.edu
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qtest_server_send is a function pointer specifying the handler used to
transmit data to the qtest client. In the standard configuration, this
calls the CharBackend handler, but now it is possible for other types of
handlers, e.g direct-function calls if the qtest client and server
exist within the same process (inproc)
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20200220041118.23264-6-alxndr@bu.edu
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A program might rely on functions implemented in vl.c, but implement its
own main(). By placing main into a separate source file, there are no
complaints about duplicate main()s when linking against vl.o. For
example, the virtual-device fuzzer uses a main() provided by libfuzzer,
and needs to perform some initialization before running the softmmu
initialization. Now, main simply calls three vl.c functions which
handle the guest initialization, main loop and cleanup.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20200220041118.23264-3-alxndr@bu.edu
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When option -mem-prealloc is used with one or more memory-backend
objects, created backends may not obey configured bind policy or
creation may fail after kernel attempts to move pages according
to bind policy.
Reason is in file_ram_alloc(), which will pre-allocate
any descriptor based RAM if global mem_prealloc != 0 and that
happens way before bind policy is applied to memory range.
One way to fix it would be to extend memory_region_foo() API
and add more invariants that could broken later due implicit
dependencies that's hard to track.
Another approach is to drop adhoc main RAM allocation and
consolidate it around memory-backend. That allows to have
single place that allocates guest RAM (main and memdev)
in the same way and then global mem_prealloc could be
replaced by backend's property[s] that will affect created
memory-backend objects but only in correct order this time.
With main RAM now converted to hostmem backends, there is no
point in keeping global mem_prealloc around, so alias
-mem-prealloc to "memory-backend.prealloc=on"
machine compat[*] property and make mem_prealloc a local
variable to only stir registration of compat property.
*) currently user accessible -global works only with DEVICE
based objects and extra work is needed to make it work
with hostmem backends. But that is convenience option
and out of scope of this already huge refactoring.
Hence machine compat properties were used.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200219160953.13771-78-imammedo@redhat.com>
the property will allow user to specify number of threads to use
in pre-allocation stage. It also will allow to reduce implicit
hostmem dependency on current_machine.
On object creation it will default to 1, but via machine
compat property it will be updated to MachineState::smp::cpus
to keep current behavior for hostmem and main RAM (which is
now also hostmem based).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200219160953.13771-77-imammedo@redhat.com>
It's no longer used anywhere beside main(),
so make it local variable that is used for CLI compat
purposes to keep -mem-path option working.
Under hood QEMU will use it to create
memory-backend-file,mem-path=...
backend and use its MemoryRegion as main RAM.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200219160953.13771-76-imammedo@redhat.com>
In case of NUMA there are 2 cases to consider:
1. '-numa node,memdev', the only one that will be available
for 5.0 and newer machine types.
In this case reuse current behavior, with only difference
memdevs are put into MachineState::ram container +
a temporary glue to keep memory_region_allocate_system_memory()
working until all boards converted.
2. fake NUMA ("-numa node mem" and default RAM splitting)
the later has been deprecated and will be removed but the former
is going to stay available for compat reasons for 5.0 and
older machine types
it takes allocate_system_memory_nonnuma() path, like non-NUMA
case and falls under conversion to memdev. So extend non-NUMA
MachineState::ram initialization introduced in previous patch
to take care of fake NUMA case.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200219160953.13771-6-imammedo@redhat.com>
Allow machine to opt in for hostmem backend based initial RAM
even if user uses old -mem-path/prealloc options by providing
MachineClass::default_ram_id
Follow up patches will incrementally convert machines to new API,
by dropping memory_region_allocate_system_memory() and setting
default_ram_id that board used to use before conversion to keep
migration stream the same.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200219160953.13771-4-imammedo@redhat.com>
Both the system emulators and tools with QMP support (specifically, the
planned storage daemon) will need to parse monitor options, so move that
code to monitor/monitor.c, which can be linked into binaries that aren't
a system emulator.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200129102239.31435-2-kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The define is only used in one other place. Move the code there
instead of keeping this xen-specific define in sysemu.h.
Message-Id: <20200121161747.10569-1-thuth@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The no_quit variable has been removed in commit 78782712a6 ("vl: drop
no_quit variable"), so let's remove the extern declaration in the header
now, too.
Fixes: 78782712a6 ("vl: drop no_quit variable")
Message-Id: <20200108192402.19672-1-thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Implement support for TPM on ppc64 by implementing the vTPM CRQ interface
as a frontend. It can use the tpm_emulator driver backend with the external
swtpm.
The Linux vTPM driver for ppc64 works with this emulation.
This TPM emulator also handles the TPM 2 case.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-4-stefanb@linux.ibm.com>
[dwg: Use device_class_set_props(), tweak Kconfig]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The accel/ code only accesses the MachineState::accel field.
As we simply want to access the accelerator, not the machine,
add a current_accel() wrapper.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200121110349.25842-9-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle bit 1 write, then post event to monitor.
Suggested by Paolo, declear a new event, using GUEST_PANICKED could
cause upper layers to react by shutting down or rebooting the guest.
In advance for extention, add GuestPanicInformation in event message.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20200114023102.612548-3-pizhenwei@bytedance.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeFbG8AAoJEL/70l94x66DCpMIAKBwxBL+VegqI+ySKgmtIBQX
LtU+ardEeZ37VfWfvuWzTFe+zQ0hsFpz/e0LHE7Ae+LVLMNWXixlmMrTIm+Xs762
hJzxBjhUhkdrMioVYTY16Kqap4Nqaxu70gDQ32Ve2sY6xYGxYLSaJooBOU5bXVgb
HPspHFVpeP6ZshBd1n2LXsgURE6v3AjTwqcsPCkL/AESFdkdOsoHeXjyKWJG1oPy
W7btzlUEqVsauZI8/PhhW/8hZUvUsJVHonYLTZTyy8aklU7aOILSyT2uPXFBVUVQ
irkQjLtD4dWlogBKO4i/QHMuwV+Asa57WNPmqv3EcIWPUWmTY84H0g2AxRgcc2M=
=48jx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Compat machines fix (Denis)
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
# gpg: Signature made Wed 08 Jan 2020 10:41:00 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (38 commits)
chardev: Use QEMUChrEvent enum in IOEventHandler typedef
chardev: use QEMUChrEvent instead of int
chardev/char: Explicit we ignore some QEMUChrEvent in IOEventHandler
monitor/hmp: Explicit we ignore a QEMUChrEvent in IOEventHandler
monitor/qmp: Explicit we ignore few QEMUChrEvent in IOEventHandler
virtio-console: Explicit we ignore some QEMUChrEvent in IOEventHandler
vhost-user-blk: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-net: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-crypto: Explicit we ignore some QEMUChrEvent in IOEventHandler
ccid-card-passthru: Explicit we ignore QEMUChrEvent in IOEventHandler
hw/usb/redirect: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/usb/dev-serial: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/char/terminal3270: Explicit ignored QEMUChrEvent in IOEventHandler
hw/ipmi: Explicit we ignore some QEMUChrEvent in IOEventHandler
hw/ipmi: Remove unnecessary declarations
target/i386: Add missed features to Cooperlake CPU model
target/i386: Add new bit definitions of MSR_IA32_ARCH_CAPABILITIES
target/i386: Fix handling of k_gs_base register in 32-bit mode in gdbstub
hw/rtc/mc146818: Add missing dependency on ISA Bus
hw/nvram/Kconfig: Restrict CHRP NVRAM to machines using OpenBIOS or SLOF
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Record/replay feature of icount allows deterministic running of execution
scenarios. Some CPUs and peripheral devices read random numbers from
external sources making deterministic execution impossible.
This patch adds recording and replaying of random read operations
into guest-random module, which is used by the virtual hardware.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <157675984852.14505.15709141760677102489.stgit@pasha-Precision-3630-Tower>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add -numa hmat-cache option to provide Memory Side Cache Information.
These memory attributes help to build Memory Side Cache Information
Structure(s) in ACPI Heterogeneous Memory Attribute Table (HMAT).
Before using hmat-cache option, enable HMAT with -machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-4-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Add -numa hmat-lb option to provide System Locality Latency and
Bandwidth Information. These memory attributes help to build
System Locality Latency and Bandwidth Information Structure(s)
in ACPI Heterogeneous Memory Attribute Table (HMAT). Before using
hmat-lb option, enable HMAT with -machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-3-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
In ACPI 6.3 chapter 5.2.27 Heterogeneous Memory Attribute Table (HMAT),
The initiator represents processor which access to memory. And in 5.2.27.3
Memory Proximity Domain Attributes Structure, the attached initiator is
defined as where the memory controller responsible for a memory proximity
domain. With attached initiator information, the topology of heterogeneous
memory can be described. Add new machine property 'hmat' to enable all
HMAT specific options.
Extend CLI of "-numa node" option to indicate the initiator numa node-id.
In the linux kernel, the codes in drivers/acpi/hmat/hmat.c parse and report
the platform's HMAT tables. Before using initiator option, enable HMAT with
-machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Jingqi Liu <jingqi.liu@intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-2-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both gsi_handler() and kvm_pc_gsi_handler() have the same content,
except one comment. Move the comment, and de-duplicate the code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVMState struct is opaque, so provide accessors for the fields
that will be moved from current_machine to the accelerator. For now
they just forward to the machine object, but this will change.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-tb-size fits nicely in the new framework for accelerator-specific options. It
is a very niche option, so insta-deprecate it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the ad-hoc qemu_tcg_configure with generic code invoking QOM
property getters and setters. More properties (and thus more valid
-accel suboptions) will be added in the next patches, which will move
accelerator-related "-machine" options to accelerators.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will have to set QOM properties before accel_init_machine, based on the
options provided to -accel. Construct the object outside it so that it
will be possible to iterate on properties between object_new_with_class
and accel_init_machine.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The next step is to move the parsing of "-machine accel=..." into vl.c,
unifying it with the configure_accelerators() function that has just
been introduced. This way, we will be able to desugar it into multiple
"-accel" options, without polluting accel/accel.c.
The CONFIG_TCG and CONFIG_KVM symbols are not available in vl.c, but
we can use accel_find instead to find their value at runtime. Once we
know that the binary has one of TCG or KVM, the default accelerator
can be expressed simply as "tcg:kvm", because TCG never fails to initialize.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have a setenv() wrapper in os-win32.c that no one is actually using.
Drop it and change to g_setenv() uniformly.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1576074210-52834-7-git-send-email-pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It's been deprecated since QEMU v3.1. We've explicitly asked in the
deprecation message that people should speak up on qemu-devel in case
they are still actively using the bluetooth part of QEMU, but nobody
ever replied that they are really still using it.
I've tried it on my own to use this bluetooth subsystem for one of my
guests, but I was also not able to get it running anymore: When I was
trying to pass-through a real bluetooth device, either the guest did
not see the device at all, or the guest crashed.
Even worse for the emulated device: When running
qemu-system-x86_64 -bt device:keyboard
QEMU crashes once you hit a key.
So it seems like the bluetooth stack is not only neglected, it is
completely bitrotten, as far as I can tell. The only attention that
this code got during the past years were some CVEs that have been
spotted there. So this code is a burden for the developers, without
any real benefit anymore. Time to remove it.
Note: hw/bt/Kconfig only gets cleared but not removed here yet.
Otherwise there is a problem with the *-softmmu/config-devices.mak.d
dependency files - they still contain a reference to this file which
gets evaluated first on some build hosts, before the file gets
properly recreated. To avoid breaking these builders, we still need
the file around for some time. It will get removed in a couple of
weeks instead.
Message-Id: <20191120091014.16883-4-thuth@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Awareness of an in kernel irqchip is usually local to the machine and its
top-level interrupt controller. However, in a few cases other things need
to know about it. In particular vfio devices need this in order to
accelerate interrupt delivery.
If interrupt routing is changed, such devices may need to readjust their
connection to the KVM irqchip. pci_bus_fire_intx_routing_notifier() exists
to do just this.
However, for the pseries machine type we have a situation where the routing
remains constant but the top-level irq chip itself is changed. This occurs
because of PAPR feature negotiation which allows the guest to decide
between the older XICS and newer XIVE irq chip models (both of which are
paravirtualized).
To allow devices like vfio to adjust to this change, introduce a new
notifier for the purpose kvm_irqchip_change_notify().
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Using fw_cfg, supply logical CHS values directly from QEMU to the BIOS.
Non-standard logical geometries break under QEMU.
A virtual disk which contains an operating system which depends on
logical geometries (consistent values being reported from BIOS INT13
AH=08) will most likely break under QEMU/SeaBIOS if it has non-standard
logical geometries - for example 56 SPT (sectors per track).
No matter what QEMU will report - SeaBIOS, for large enough disks - will
use LBA translation, which will report 63 SPT instead.
In addition we cannot force SeaBIOS to rely on physical geometries at
all. A virtio-blk-pci virtual disk with 255 phyiscal heads cannot
report more than 16 physical heads when moved to an IDE controller,
since the ATA spec allows a maximum of 16 heads - this is an artifact of
virtualization.
By supplying the logical geometries directly we are able to support such
"exotic" disks.
We serialize this information in a similar way to the "bootorder"
interface.
The new fw_cfg entry is "bios-geometry".
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add an interface to provide direct logical CHS values for boot devices.
We will use this interface in the next commits.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
We have two drivers (iscsi and file-posix) that (in some cases) return
success from their .bdrv_co_truncate() implementation if the block
device is larger than the requested offset, but cannot be shrunk. Some
callers do not want that behavior, so this patch adds a new parameter
that they can use to turn off that behavior.
This patch just adds the parameter and lets the block/io.c and
block/block-backend.c functions pass it around. All other callers
always pass false and none of the implementations evaluate it, so that
this patch does not change existing behavior. Future patches take care
of that.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add blk write function with qiov_offset parameter. It's needed for the
following commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191011090711.19940-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Replay is capable of recording normal BH events, but sometimes
there are single use callbacks scheduled with aio_bh_schedule_oneshot
function. This patch enables recording and replaying such callbacks.
Block layer uses these events for calling the completion function.
Replaying these calls makes the execution deterministic.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VMX requires 64-bit feature words for the IA32_VMX_EPT_VPID_CAP
and IA32_VMX_BASIC MSRs. (The VMX control MSRs are 64-bit wide but
actually have only 32 bits of information).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Max memslot size supported by kvm on s390 is 8Tb,
move logic of splitting RAM in chunks upto 8T to KVM code.
This way it will hide KVM specific restrictions in KVM code
and won't affect board level design decisions. Which would allow
us to avoid misusing memory_region_allocate_system_memory() API
and eventually use a single hostmem backend for guest RAM.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190924144751.24149-4-imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move existing numa global have_numa_distance into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-4-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Commit a5e0b3311 removed these in favour of querying machine
properties. Remove the extern declarations as well.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190711130546.18578-1-alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Like Xu <like.xu@linux.intel.com>
Fixes: a5e0b33119 ("vl.c: Replace smp global variables with smp machine properties")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KtI3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kraxel/tags/audio-20190821-pull-request' into staging
audio: second batch of -audiodev support, adding support for multiple backends.
# gpg: Signature made Wed 21 Aug 2019 09:40:37 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/audio-20190821-pull-request:
audio: fix memory leak reported by ASAN
audio: use size_t where makes sense
audio: remove read and write pcm_ops
paaudio: fix playback glitches
audio: do not run each backend in audio_run
audio: remove audio_MIN, audio_MAX
paaudio: properly disconnect streams in fini_*
paaudio: do not move stream when sink/source name is specified
audio: audiodev= parameters no longer optional when -audiodev present
paaudio: prepare for multiple audiodev
audio: add audiodev properties to frontends
audio: add audiodev property to vnc and wav_capture
audio: basic support for multi backend audio
audio: reduce glob_audio_state usage
audio: Add missing fall through comments
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
This patch renames replay_get_current_step() and related variables
to make these names consistent with existing 'icount' command line
option and future record/replay hmp/qmp commands.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <156404428377.18669.15476429889039912070.stgit@pasha-Precision-3630-Tower>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- file-posix: Fix O_DIRECT alignment detection
- Fixes for concurrent block jobs
- block-backend: Queue requests while drained (fix IDE vs. job crashes)
- qemu-img convert: Deprecate using -n and -o together
- iotests: Migration tests with filter nodes
- iotests: More media change tests
-----BEGIN PGP SIGNATURE-----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=T7L5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- file-posix: Fix O_DIRECT alignment detection
- Fixes for concurrent block jobs
- block-backend: Queue requests while drained (fix IDE vs. job crashes)
- qemu-img convert: Deprecate using -n and -o together
- iotests: Migration tests with filter nodes
- iotests: More media change tests
# gpg: Signature made Fri 16 Aug 2019 10:29:18 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
file-posix: Handle undetectable alignment
qemu-img convert: Deprecate using -n and -o together
block-backend: Queue requests while drained
mirror: Keep mirror_top_bs drained after dropping permissions
block: Remove blk_pread_unthrottled()
iotests: Add test for concurrent stream/commit
tests: Test mid-drain bdrv_replace_child_noperm()
tests: Test polling in bdrv_drop_intermediate()
block: Reduce (un)drains when replacing a child
block: Keep subtree drained in drop_intermediate
block: Simplify bdrv_filter_default_perms()
iotests: Test migration with all kinds of filter nodes
iotests: Move migration helpers to iotests.py
iotests/118: Add -blockdev based tests
iotests/118: Create test classes dynamically
iotests/118: Test media change for scsi-cd
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=eSUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-include-2019-08-13-v2' into staging
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Commit e35704ba9c "numa: Move NUMA declarations from sysemu.h to
numa.h" left a few NUMA-related macros behind. Move them now.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-26-armbru@redhat.com>
Move the HostMemoryBackend typedef from sysemu/hostmem.h to
qemu/typedefs.h. This renders a few inclusions of sysemu/hostmem.h
superfluous; drop them.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-25-armbru@redhat.com>
sysemu/numa.h includes hw/boards.h just for the CPUArchId typedef, at
the cost of pulling in more than two dozen extra headers indirectly.
I could move the typedef from hw/boards.h to qemu/typedefs.h. But
it's used in just two headers: boards.h and numa.h.
I could move it to another header both its users include.
exec/cpu-common.h seems to be the least bad fit.
But I'm keeping this simple & stupid: declare the struct tag in
numa.h.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-24-armbru@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-20-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
migration/qemu-file.h neglects to include it even though it needs
ram_addr_t. Fix that. Drop a few superfluous inclusions elsewhere.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-14-armbru@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Some of the generated qapi-types-MODULE.h are included all over the
place. Changing a QAPI type can trigger massive recompiling. Top
scorers recompile more than 1000 out of some 6600 objects (not
counting tests and objects that don't depend on qemu/osdep.h):
6300 qapi/qapi-builtin-types.h
5700 qapi/qapi-types-run-state.h
3900 qapi/qapi-types-common.h
3300 qapi/qapi-types-sockets.h
3000 qapi/qapi-types-misc.h
3000 qapi/qapi-types-crypto.h
3000 qapi/qapi-types-job.h
3000 qapi/qapi-types-block-core.h
2800 qapi/qapi-types-block.h
1300 qapi/qapi-types-net.h
Clean up headers to include generated QAPI headers only where needed.
Impact is negligible except for hw/qdev-properties.h.
This header includes qapi/qapi-types-block.h and
qapi/qapi-types-misc.h. They are used only in expansions of property
definition macros such as DEFINE_PROP_BLOCKDEV_ON_ERROR() and
DEFINE_PROP_OFF_AUTO(). Moving their inclusion from
hw/qdev-properties.h to the users of these macros avoids pointless
recompiles. This is how other property definition macros, such as
DEFINE_PROP_NETDEV(), already work.
Improves things for some of the top scorers:
3600 qapi/qapi-types-common.h
2800 qapi/qapi-types-sockets.h
900 qapi/qapi-types-misc.h
2200 qapi/qapi-types-crypto.h
2100 qapi/qapi-types-job.h
2100 qapi/qapi-types-block-core.h
270 qapi/qapi-types-block.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-3-armbru@redhat.com>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This fixes devices like IDE that can still start new requests from I/O
handlers in the CPU thread while the block backend is drained.
The basic assumption is that in a drain section, no new requests should
be allowed through a BlockBackend (blk_drained_begin/end don't exist,
we get drain sections only on the node level). However, there are two
special cases where requests should not be queued:
1. Block jobs: We already make sure that block jobs are paused in a
drain section, so they won't start new requests. However, if the
drain_begin is called on the job's BlockBackend first, it can happen
that we deadlock because the job stays busy until it reaches a pause
point - which it can't if its requests aren't processed any more.
The proper solution here would be to make all requests through the
job's filter node instead of using a BlockBackend. For now, just
disabling request queuing on the job BlockBackend is simpler.
2. In test cases where making requests through bdrv_* would be
cumbersome because we'd need a BdrvChild. As we already got the
functionality to disable request queuing from 1., use it in tests,
too, for convenience.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The functionality offered by blk_pread_unthrottled() goes back to commit
498e386c58. Then, we couldn't perform I/O throttling with synchronous
requests because timers wouldn't be executed in polling loops. So the
commit automatically disabled I/O throttling as soon as a synchronous
request was issued.
However, for geometry detection during disk initialisation, we always
used (and still use) synchronous requests even if guest requests use AIO
later. Geometry detection was not wanted to disable I/O throttling, so
bdrv_pread_unthrottled() was introduced which disabled throttling only
temporarily.
All of this isn't necessary any more because we do run timers in polling
loop and even synchronous requests are now using coroutine
infrastructure internally. For this reason, commit 90c78624f already
removed the automatic disabling of I/O throttling.
It's time to get rid of the workaround for the removed code, and its
abuse of blk_root_drained_begin()/end(), as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Both the qtest client, libqtest.c, and server, qtest.c, used the same
name for initialization functions which can cause confusion.
Signed-off-by: Alexander Oleinik <alxndr@bu.edu>
Message-Id: <20190805031240.6024-1-alxndr@bu.edu>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This adds an accelerator name to the "into mtree -f" to tell the user if
a particular memory section is registered with the accelerator;
the primary user for this is KVM and such information is useful
for debugging purposes.
This adds a has_memory() callback to the accelerator class allowing any
accelerator to have a label in that memory tree dump.
Since memory sections are passed to memory listeners and get registered
in accelerators (rather than memory regions), this only prints new labels
for flatviews attached to the system address space.
An example:
Root memory region: system
0000000000000000-0000002fffffffff (prio 0, ram): /objects/mem0 kvm
0000003000000000-0000005fffffffff (prio 0, ram): /objects/mem1 kvm
0000200000000020-000020000000003f (prio 1, i/o): virtio-pci
0000200080000000-000020008000003f (prio 0, i/o): capabilities
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190614015237.82463-1-aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce KVMMemoryListener.slots_lock to protect the slots inside the
kvm memory listener. Currently it is close to useless because all the
KVM code path now is always protected by the BQL. But it'll start to
make sense in follow up patches where we might do remote dirty bitmap
clear and also we'll update the per-slot cached dirty bitmap even
without the BQL. So let's prepare for it.
We can also use per-slot lock for above reason but it seems to be an
overkill. Let's just use this bigger one (which covers all the slots
of a single address space) but anyway this lock is still much smaller
than the BQL.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190603065056.25211-10-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When synchronizing dirty bitmap from kernel KVM we do it in a
per-kvmslot fashion and we allocate the userspace bitmap for each of
the ioctl. This patch instead make the bitmap cache be persistent
then we don't need to g_malloc0() every time.
More importantly, the cached per-kvmslot dirty bitmap will be further
used when we want to add support for the KVM_CLEAR_DIRTY_LOG and this
cached bitmap will be used to guarantee we won't clear any unknown
dirty bits otherwise that can be a severe data loss issue for
migration code.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190603065056.25211-9-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add an API for registering vm change state handlers with a well-defined
ordering. This is necessary when handlers depend on each other.
Small coding style fixes are included to make checkpatch.pl happy.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move commands dump-guest-memory, query-dump,
query-dump-guest-memory-capability with their types from misc.json to
new dump.json. Add dump.json to MAINTAINERS section "Dump".
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-15-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The handlers for qapi/machine.json's QMP commands are spread over
cpus.c, hw/core/numa.c, monitor/misc.c, monitor/qmp-cmds.c, and vl.c.
Move them all to new hw/core/machine-qmp-cmds.c, where they are
covered by MAINTAINERS section "Machine core", just like
qapi/machine.json.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-11-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Move commands cpu-add, query-cpus, query-cpus-fast,
query-current-machine, query-hotpluggable-cpus, query-machines,
query-memdev, and set-numa-node with their types from misc.json to new
machine.json. Also move types X86CPURegister32 and
X86CPUFeatureWordInfo. Add machine.json to MAINTAINERS section
"Machine core".
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-9-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Kernel commit 8fcc4b5923af ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
introduced new IOCTLs to extract and restore vCPU state related to
Intel VMX & AMD SVM.
Utilize these IOCTLs to add support for migration of VMs which are
running nested hypervisors.
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Tested-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-9-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simiar to how kvm_init_vcpu() calls kvm_arch_init_vcpu() to perform
arch-dependent initialisation, introduce kvm_arch_destroy_vcpu()
to be called from kvm_destroy_vcpu() to perform arch-dependent
destruction.
This was added because some architectures (Such as i386)
currently do not free memory that it have allocated in
kvm_arch_init_vcpu().
Suggested-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-3-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
The AccelType type was converted to AccelClass QOM
object on b14a0b7469, and the original data type had
a field to store the option name which in turn was
used to search an accelerator. The lookup method
(accel_find) changed too, making the option field
unnecessary but it became AccelClass::opt_name despite
that. Therefore, and given that none accelerator
implementation sets AccelClass::opt_name, let's
remove this attribute.
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-Id: <20190531165334.20403-2-wainersm@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This adds a new parameter to blk_new() which requires its callers to
declare from which AioContext this BlockBackend is going to be used (or
the locks of which AioContext need to be taken anyway).
The given context is only stored and kept up to date when changing
AioContexts. Actually applying the stored AioContext to the root node
is saved for another commit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error parameter to blk_set_aio_context() and use
bdrv_child_try_set_aio_context() internally to check whether all
involved nodes can actually support the AioContext switch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for having some more common semihosting code let's
excise the current config magic from vl.c into its own file. We shall
later add more conditionals to the build configurations so we can
avoid building this if we don't need it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Some users (like block jobs) can tolerate an AioContext change for their
BlockBackend. Add a function that tells the BlockBackend that it can
allow changes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Create a vhost-user-backend object that holds a connection to a
vhost-user backend (or "slave" process) and can be referenced from
virtio devices that support it. See later patches for input & gpu
usage.
Note: a previous iteration of this object made it user-creatable, and
allowed managed sub-process spawning, but that has been dropped for
now.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190503130034.24916-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The field is not used anymore, we can remove it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190422210448.2488-4-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com> [on mingw64]
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_available() will always return 0 on non-POSIX systems.
It's simpler to just not compile the accelerator code on those
systems instead of relying on the AccelClass::available function.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190422210448.2488-3-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com> [on mingw64]
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The various TARGET_cpu_list() take an fprintf()-like callback and a
FILE * to pass to it. Their callers (vl.c's main() via list_cpus(),
bsd-user/main.c's main(), linux-user/main.c's main()) all pass
fprintf() and stdout. Thus, the flexibility provided by the (rather
tiresome) indirection isn't actually used.
Drop the callback, and call qemu_printf() instead.
Calling printf() would also work, but would make the code unsuitable
for monitor context without making it simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417191805.28198-10-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dump_drift_info() takes an fprintf()-like callback and a FILE * to pass
to it.
Its only caller hmp_info_jit() passes monitor_fprintf() and a Monitor
* cast to FILE *. monitor_fprintf() casts it right back, and is
otherwise identical to monitor_printf(). The type-punning is ugly.
Drop the callback, and call qemu_printf() instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-6-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-2-armbru@redhat.com>
This reverts commit 3df663e575.
This reverts commit b605c47b57.
Command line option --only-migratable is for disallowing any
configuration that can block migration.
Initially, --only-migratable set global variable @only_migratable.
Commit 3df663e575 "migration: move only_migratable to MigrationState"
replaced it by MigrationState member @only_migratable. That was a
mistake.
First, it doesn't make sense on the design level. MigrationState
captures the state of an individual migration, but --only-migratable
isn't a property of an individual migration, it's a restriction on
QEMU configuration. With fault tolerance, we could have several
migrations at once. --only-migratable would certainly protect all of
them. Storing it in MigrationState feels inappropriate.
Second, it contributes to a dependency cycle that manifests itself as
a bug now.
Putting @only_migratable into MigrationState means its available only
after migration_object_init().
We can't set it before migration_object_init(), so we delay setting it
with a global property (this is fixup commit b605c47b57 "migration:
fix handling for --only-migratable").
We can't get it before migration_object_init(), so anything that uses
it can only run afterwards.
Since migrate_add_blocker() needs to obey --only-migratable, any code
adding migration blockers can run only afterwards. This contributes
to the following dependency cycle:
* configure_blockdev() must run before machine_set_property()
so machine properties can refer to block backends
* machine_set_property() before configure_accelerator()
so machine properties like kvm-irqchip get applied
* configure_accelerator() before migration_object_init()
so that Xen's accelerator compat properties get applied.
* migration_object_init() before configure_blockdev()
so configure_blockdev() can add migration blockers
The cycle was closed when recent commit cda4aa9a5a "Create block
backends before setting machine properties" added the first
dependency, and satisfied it by violating the last one. Broke block
backends that add migration blockers.
Moving @only_migratable into MigrationState was a mistake. Revert it.
This doesn't quite break the "migration_object_init() before
configure_blockdev() dependency, since migrate_add_blocker() still has
another dependency on migration_object_init(). To be addressed the
next commit.
Note that the reverted commit made -only-migratable sugar for -global
migration.only-migratable=on below the hood. Documentation has only
ever mentioned -only-migratable. This commit removes the arcane &
undocumented alternative to -only-migratable again. Nobody should be
using it.
Conflicts:
include/migration/misc.h
migration/migration.c
migration/migration.h
vl.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190401090827.20793-3-armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The next patch needs access to a device's minimum permitted
alignment, since NBD wants to advertise this to clients. Add
an accessor function, borrowing from blk_get_max_transfer()
for accessing a backend's block limits.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20190329042750.14704-6-eblake@redhat.com>
The 'boot_splash_filedata_size' was introduced as a global variable
in 3d3b8303c6. This variable is used as a 'size' argument to the
fw_cfg_add_file(). This function has an interface contract with its
'data' argument, but there is no such contract for 'size' (this is
not a referenced pointer). We can simply remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308013222.12524-7-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In existing code we create the gcontext dynamically at the first
access of the gcontext from caller. That can bring some complexity
and potential races during using iothread. Since the context itself
is not that big a resource, and we won't have millions of iothread,
let's simply create the gcontext unconditionally.
This will also be a preparation work further to move the thread
context push operation earlier than before (now it's only pushed right
before we want to start running the gmainloop).
Removing the g_once since it's not necessary, while introducing a new
run_gcontext boolean to show whether we want to run the gcontext.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 20190306115532.23025-3-peterx@redhat.com
Message-Id: <20190306115532.23025-3-peterx@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Only sending an init-done message using lock+cond seems an overkill to
me. Replacing it with a simpler semaphore.
Meanwhile, init the semaphore unconditionally, then we can destroy it
unconditionally too in finalize which seems cleaner.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 20190306115532.23025-2-peterx@redhat.com
Message-Id: <20190306115532.23025-2-peterx@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Switch the announcements to using the new announce timer.
Move the code that does it to announce.c rather than savevm
because it really has nothing to do with the actual migration.
Migration starts the announce from bh's and so they're all
in the main thread/bql, and so there's never any racing with
the timers themselves.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
For some users of BlockBackends, just increasing the in_flight counter
is easier than implementing separate handlers in BlockDevOps. Make the
helper functions for this public.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The -no-frame option has been deprecated with QEMU v2.12. It was only
useful with SDL1.2 - now that we've removed support for SDL1.2, we
can certainly remove the -no-frame option, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1549351769-19620-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The last user of blk_attach_dev_legacy() was the code in xen_disk which
has recently been reworked. Now there is no user for this legacy function
anymore. Thus we can finally remove all code related to the "legacy_dev"
flag, too, and turn the related "void *" in block-backend.c into proper
"DeviceState *" to fix some of the remaining TODOs there.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a new command, returning block nodes (and their users) graph.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20181221170909.25584-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Files requiring HCIInfo already include "sysemu/bt.h".
To clean "qemu/typedefs.h", move the declaration to "sysemu/bt.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When compiling with "--disable-tcg", we currently still use "tcg"
as default accelerator. "kvm" should be used in this case instead.
Also, some downstream distros provide QEMU binaries which have "kvm"
in their names (e.g. "qemu-kvm" on RHEL or "kvm" on Ubuntu) that use
KVM by default - and some users might want to do something similar
with upstream binaries, too. Accomodate them by using "kvm:tcg" as
default when we detect such a binary name.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1538748792-19444-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hostmem-file and hostmem-memfd use the whole object path for the
memory region name, and hostname-ram uses only the path component (the
object id, or canonical path basename):
qemu -m 1024 -object memory-backend-file,id=mem,size=1G,mem-path=/tmp/foo -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-memfd,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-ram,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
For consistency, change to use object id for -file and -memfd as well
with >= 4.0.
Having a consistent naming allows to migrate to different hostmem
backends.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of registering compat properties as globals, let's keep them
in their own array, to avoid mixing with user globals.
Introduce object_apply_global_props() function, to apply compatibility
properties from a GPtrArray.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
qemu_extra_params_fw[] has external linkage, but is used
only in fw_cfg_bootsplash(), it makes sense to make it
locally.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-4-git-send-email-liq3ea@gmail.com>
[PMD: Removed qemu_extra_params_fw declaration in vl.c]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Notifier will be used for signaling shutdown event to inform system is
shutdown. This will allow devices and other component to run some
cleanup code needed before VM is shutdown.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181204172535.2799-1-armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When issuing the qmp/hmp 'system_wakeup' command, what happens in a
nutshell is:
- qmp_system_wakeup_request set runstate to RUNNING, sets a wakeup_reason
and notify the event
- in the main_loop, all vcpus are paused, a system reset is issued, all
subscribers of wakeup_notifiers receives a notification, vcpus are then
resumed and the wake up QAPI event is fired
Note that this procedure alone doesn't ensure that the guest will awake
from SUSPENDED state - the subscribers of the wake up event must take
action to resume the guest, otherwise the guest will simply reboot. At
this moment, only the ACPI machines via acpi_pm1_cnt_init and xen_hvm_init
have wake-up from suspend support.
However, only the presence of 'system_wakeup' is required for QGA to
support 'guest-suspend-ram' and 'guest-suspend-hybrid' at this moment.
This means that the user/management will expect to suspend the guest using
one of those suspend commands and then resume execution using system_wakeup,
regardless of the support offered in system_wakeup in the first place.
This patch creates a new API called query-current-machine [1], that holds
a new flag called 'wakeup-suspend-support' that indicates if the guest
supports wake up from suspend via system_wakeup. The machine is considered
to implement wake-up support if a call to a new 'qemu_register_wakeup_support'
is made during its init, as it is now being done inside acpi_pm1_cnt_init
and xen_hvm_init. This allows for any other machine type to declare wake-up
support regardless of ACPI state or wakeup_notifiers subscription, making easier
for newer implementations that might have their own mechanisms in the future.
This is the expected output of query-current-machine when running a x86
guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": true}}
Running the same x86 guest, but with the --no-acpi option:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
This is the output when running a pseries guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
With this extra tool, management can avoid situations where a guest
that does not have proper suspend/wake capabilities ends up in
inconsistent state (e.g.
https://github.com/open-power-host-os/qemu/issues/31).
[1] the decision of creating the query-current-machine API is based
on discussions in the QEMU mailing list where it was decided that
query-target wasn't a proper place to store the wake-up flag, neither
was query-machines because this isn't a static property of the
machine object. This new API can then be used to store other
dynamic machine properties that are scattered around the code
ATM. More info at:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg04235.html
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-2-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Needed so the patch after next can add ShutdownCause to QMP events
SHUTDOWN and RESET.
Signed-off-by: Dominik Csapak <d.csapak@proxmox.com>
Message-Id: <20181205110131.23049-2-d.csapak@proxmox.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
There's no reason to violate our naming conventions by having a
struct with a different name than its typedef. Messed up since
its introduction in commit 8c85901e, but made more obvious when
commit 3bfe5716 promoted it to typedefs.h.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181115211752.1295571-3-eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add kvm_get_supported_feature_msrs() to get supported MSR feature index list.
Add kvm_arch_get_supported_msr_feature() to get each MSR features value.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1539578845-37944-2-git-send-email-robert.hu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----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=kPZX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-error-2018-10-22' into staging
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling error_report() from within a function that takes an Error **
argument is suspicious. drive_new() calls error_report() even though
it can run within drive_init_func(), which takes an Error ** argument.
drive_init_func()'s caller main(), via qemu_opts_foreach(), is fine
with it, but clean it up anyway:
* Convert drive_new() to Error
* Update add_init_drive() to report the error received from
drive_new()
* Make main() pass &error_fatal through qemu_opts_foreach(),
drive_init_func() to drive_new()
* Make default_drive() pass &error_abort through qemu_opts_foreach(),
drive_init_func() to drive_new()
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20181017082702.5581-34-armbru@redhat.com>
Calling error_report() in a function that takes an Error ** argument
is suspicious. tpm_init_tpmdev() does that, and then fails without
setting an error. Its caller main(), via tpm_init() and
qemu_opts_foreach(), is fine with it, but clean it up anyway.
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20181017082702.5581-30-armbru@redhat.com>
Calling error_report() in a function that takes an Error ** argument
is suspicious. parse_numa() does that, and then fails without setting
an error. Its caller main(), via qemu_opts_foreach(), is fine with
it, but clean it up anyway.
While there, give parse_numa() internal linkage.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181017082702.5581-29-armbru@redhat.com>
accel_init_machine sets *(acc->allowed) to true if acc->init_machine(ms)
succeeds. There's no need to have both hvf_allowed and hvf_disabled.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20181018143051.48508-1-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In record/replay icount mode vCPU thread and iothread synchronize
the execution using the checkpoints.
vCPU thread processes the virtual timers and iothread processes all others.
When iothread wants to wake up sleeping vCPU thread, it sends dummy queued
work. Therefore it could be the following sequence of the events in
record mode:
- IO: sending dummy work
- IO: processing timers
- CPU: wakeup
- CPU: clearing dummy work
- CPU: processing virtual timers
But due to the races in replay mode the sequence may change:
- IO: sending dummy work
- CPU: wakeup
- CPU: clearing dummy work
- CPU: sleeping again because nothing to do
- IO: Processing timers
- CPU: zzzz
In this case vCPU will not wake up, because dummy work is not to be set up
again.
This patch tries to wake up the vCPU when it sleeps and the icount warp
checkpoint isn't met. It means that vCPU has something to do, because
there are no other reasons of non-matching warp checkpoint.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
--
v5: improve checking that vCPU is still sleeping
Message-Id: <20180912081945.3228.19776.stgit@pasha-VirtualBox>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the older machines (such as Mac and SPARC) the DT nodes representing
bootdevices for disk nodes are irregular for mainly historical reasons.
Since the majority of bootdevice nodes for these machines either do not have a
separate disk node or require different (custom) names then it is much easier
for processing to just disable all suffixes for a particular machine.
Introduce a new ignore_boot_device_suffixes MachineClass property to control
bootdevice suffix generation, defaulting to false in order to preserve
compatibility.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180810124027.10698-1-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
This reinstates commit eae3bd1eb7,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option addr was deprecated in QEMU 2.10. It's time to remove
it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
This reinstates commit a7aff6dd10,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive options cyls, heads, secs and trans were deprecated in
QEMU 2.10. It's time to remove them.
hd-geo-test tested both the old version with geometry options in -drive
and the new one with -device. Therefore the code using -drive doesn't
have to be replaced there, we just need to remove the -drive test cases.
This in turn allows some simplification of the code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This reverts commit a7aff6dd10.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit eae3bd1eb7.
Reverted to avoid conflicts for geometry options revert.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass read flags and write flags separately. This is needed to handle
coming BDRV_REQ_NO_SERIALISING clearly in following patches.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
kexec/kdump as well as the bootloader use a subcode of diagnose 308
that is supposed to reset the I/O subsystem but not comprise a full
"reboot". With the latest refactoring this is now broken when
-no-reboot is used or when libvirt acts on a reboot QMP event, for
example a virt-install from iso images.
We need to mark these "subsystem resets" as special.
Fixes: a30fb811cb (s390x: refactor reset/reipl handling)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180622102928.173420-1-borntraeger@de.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This helper allows to retrieve the paths of nodes whose name
match node-name or node-name@unit-address patterns.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1530044492-24921-2-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this flag, kvm allows guest to control host CPU power state. This
increases latency for other processes using same host CPU in an
unpredictable way, but if decreases idle entry/exit times for the
running VCPU, so to use it QEMU needs a hint about whether host CPU is
overcommitted, hence the flag name.
Follow-up patches will expose this capability to guest
(using mwait leaf).
Based on a patch by Wanpeng Li <kernellwp@gmail.com> .
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20180622192148.178309-2-mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unused, so let's remove it.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-8-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to KVM commit 75d61fbc, it needs to delete the slot before
changing the KVM_MEM_READONLY flag. But QEMU commit 235e8982 only check
whether KVM_MEM_READONLY flag is set instead of changing. It doesn't
need to delete the slot if the KVM_MEM_READONLY flag is not changed.
This fixes a issue that migrating a VM at the OVMF startup stage and
VM is executing the codes in rom. Between the deleting and adding the
slot in kvm_set_user_memory_region, there is a chance that guest access
rom and trap to KVM, then KVM can't find the corresponding memslot.
While KVM (on ARM) injects an abort to guest due to the broken hva, then
guest will get stuck.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-Id: <1526462314-19720-1-git-send-email-zhaoshenglong@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
The -drive option addr was deprecated in QEMU 2.10. It's time to remove
it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
The -drive options cyls, heads, secs and trans were deprecated in
QEMU 2.10. It's time to remove them.
hd-geo-test tested both the old version with geometry options in -drive
and the new one with -device. Therefore the code using -drive doesn't
have to be replaced there, we just need to remove the -drive test cases.
This in turn allows some simplification of the code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
It's a BlockBackend wrapper of the BDS interface.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601092648.24614-10-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If CONFIG_SECCOMP is undefined, the option 'elevatedprivileges' remains
compiled. This would make libvirt set the corresponding capability and
then trigger failure during guest startup. This patch moves the code
regarding seccomp command line options to qemu-seccomp.c file and
wraps qemu_opts_foreach finding sandbox option with CONFIG_SECCOMP.
Because parse_sandbox() is moved into qemu-seccomp.c file, change
seccomp_start() to static function.
Signed-off-by: Yi Min Zhao <zyimin@linux.ibm.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Tested-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Eduardo Otubo <otubo@redhat.com>
When global_log_dirty is enabled VRAM modification tracking never
worked correctly. The address that is passed to xen_hvm_modified_memory()
is not the effective PFN but RAM block address which is not the same
for VRAM.
We need to make a translation for this address into PFN using
physmap. Since there is no way to access physmap properly inside
xen_hvm_modified_memory() let's make it a global structure.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to address_space_access_valid().
Its callers either have an attrs value to hand, or don't care
and can use MEMTXATTRS_UNSPECIFIED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-6-peter.maydell@linaro.org
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to address_space_map().
Its callers either have an attrs value to hand, or don't care
and can use MEMTXATTRS_UNSPECIFIED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-5-peter.maydell@linaro.org
This option allows pausing QEMU in the new RUN_STATE_PRECONFIG state,
allowing the configuration of QEMU from QMP before the machine jumps
into board initialization code of machine_run_board_init()
The intent is to allow management to query machine state and additionally
configure it using previous query results within one QEMU instance
(i.e. eliminate the need to start QEMU twice, 1st to query board specific
parameters and 2nd for actual VM start using query results for
additional parameters).
The new option complements -S option and could be used with or without
it. The difference is that -S pauses QEMU when the machine is completely
initialized with all devices wired up and ready to execute guest code
(QEMU needs only to unpause VCPUs to let guest execute its code),
while the "preconfig" option pauses QEMU early before board specific init
callback (machine_run_board_init) is executed and allows the configuration
of machine parameters which will be used by board init code.
When early introspection/configuration is done, command 'exit-preconfig'
should be used to exit RUN_STATE_PRECONFIG and transition to the next
requested state (i.e. if -S is used then QEMU will pause the second
time when board/device initialization is completed or start guest
execution if -S isn't provided on CLI)
PS:
Initially 'preconfig' is planned to be used for configuring numa
topology depending on board specified possible cpus layout.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1526059483-42847-1-git-send-email-imammedo@redhat.com>
[ehabkost: Changed "since 2.13" to "since 3.0"]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will allow to reuse set_numa_options() for parsing
configuration commands received via QMP interface
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1525423069-61903-3-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
in preparation for numa options to being handled via QMP before
machine_run_board_init(), move final numa configuration checks
and processing to machine_run_board_init() so it could take into
account both CLI (via parse_numa_opts()) and QMP input
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1525423069-61903-2-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Switch to the header we imported from Linux,
this allows us to drop a hack in kvm_i386.h.
More code will be dropped in the next patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "id" property is unnecessary and can be replaced simply with
object_get_canonical_path_component. This patch mostly undoes commit
e1ff3c67e8 ("monitor: fix qmp/hmp query-memdev not reporting IDs of
memory backends", 2017-01-12).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are a couple places (one generic, one target specific) where we need
to get the host page size associated with a particular memory backend. I
have some upcoming code which will add another place which wants this. So,
for convenience, add a helper function to calculate this.
host_memory_backend_pagesize() returns the host pagesize for a given
HostMemoryBackend object.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
This is called just before os_setup_post. Currently none of the
accelerators provide this hook, but the Xen one is going to provide
one in a moment.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Create a new function serial_max_hds() which returns the number of
serial ports defined by the user. This is needed only by spapr.
This allows us to remove the MAX_SERIAL_PORTS define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-14-peter.maydell@linaro.org
Instead of having a fixed sized global serial_hds[] array,
use a local dynamically reallocated one, so we don't have
a compile time limit on how many serial ports a system has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-13-peter.maydell@linaro.org
Provide an accessor function serial_hd() to return the Chardev
(if any) associated with the numbered serial port. This will
be used to replace direct accesses to the serial_hds[] array,
so that calling code doesn't need to care about the size of
that array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-7-peter.maydell@linaro.org
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
Inorder to integerate the Secure Encryption Virtualization (SEV) support
add few high-level memory encryption APIs which can be used for encrypting
the guest memory region.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split from a patch by Brijesh Singh (brijesh.singh@amd.com).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
The replay_mutex_lock/unlock/locked functions are now going to be used
for ensuring lock-step behaviour between the two threads. Make them
public API functions and also provide stubs for non-QEMU builds on
common paths.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20180227095242.1060.16601.stgit@pasha-VirtualBox>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch does not allows saving/loading vmstate when
replay events queue is not empty. There is no reliable
way to save events queue, because it describes internal
coroutine state. Therefore saving and loading operations
should be deferred to another record/replay step.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20180227095214.1060.32939.stgit@pasha-VirtualBox>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
We have that variable but not exported. Export that so modules can have
a way to poke on whether machine init has finished.
Meanwhile, set that up even before calling the notifiers, so that
notifiers who may depend on this field will get a correct answer.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180306053320.15401-2-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 00d09fdbba ("vl: pause vcpus before
stopping iothreads") and commit dce8921b2b
("iothread: Stop threads before main() quits") tried to work around the
fact that emulation was still active during termination by stopping
iothreads. They suffer from race conditions:
1. virtio_scsi_handle_cmd_vq() racing with iothread_stop_all() hits the
virtio_scsi_ctx_check() assertion failure because the BDS AioContext
has been modified by iothread_stop_all().
2. Guest vq kick racing with main loop termination leaves a readable
ioeventfd that is handled by the next aio_poll() when external
clients are enabled again, resulting in unwanted emulation activity.
This patch obsoletes those commits by fully disabling emulation activity
when vcpus are stopped.
Use the new vm_shutdown() function instead of pause_all_vcpus() so that
vm change state handlers are invoked too. Virtio devices will now stop
their ioeventfds, preventing further emulation activity after vm_stop().
Note that vm_stop(RUN_STATE_SHUTDOWN) cannot be used because it emits a
QMP STOP event that may affect existing clients.
It is no longer necessary to call replay_disable_events() directly since
vm_shutdown() does so already.
Drop iothread_stop_all() since it is no longer used.
Cc: Fam Zheng <famz@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20180307144205.20619-5-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds RISC-V into the build system enabling the following targets:
- riscv32-softmmu
- riscv64-softmmu
- riscv32-linux-user
- riscv64-linux-user
This adds defaults configs for RISC-V, enables the build for the RISC-V
CPU core, hardware, and Linux User Emulation. The 'qemu-binfmt-conf.sh'
script is updated to add the RISC-V ELF magic.
Expected checkpatch errors for consistency reasons:
ERROR: line over 90 characters
FILE: scripts/qemu-binfmt-conf.sh
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
Version: GnuPG v1
iQEcBAABAgAGBQJanLRTAAoJEO8Ells5jWIRAxsH/3wX62o+msLjJHakjcu2OTMG
vdhnB8GfjC5HgMYbovG7TJ95KXg7VRodwru9zgJheTK7DG8fG0nFRuzr8L2tSAph
3s0YTFYDXJ6MBYD//ubdX+jNnchIvMlTX6yheAzcXvQb+nCcN2efN0XpSlGR+g4D
wGi1lWKurGEJE6RUfYPpbbUkjXjbbKyclE0RL+WBmmyruerXI8OxuXQ3GuHK75fb
cZLiToyP9+qnnDyT4lceG5vGRjYLtL8t1nB01M4UTr+tlCkMMsoOjufzGB/CDUdm
oGi1OuKRw06xTLroUJ/uiwSKQH6dMbrv6sLvk92dHnL9k2ZAjv2bVAgz8eAG7o0=
=pPIZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 05 Mar 2018 03:06:59 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap: setting error appropriately when calling net_init_tap_one()
hw/net: Remove unnecessary header includes
net: Add a new convenience option "--nic" to configure default/on-board NICs
net: Remove the deprecated 'host_net_add' and 'host_net_remove' HMP commands
net: Remove the deprecated way of dumping network packets
net: Make net_client_init() static
net: Only show vhost-user in the help text if CONFIG_POSIX is defined
net: List available netdevs with "-netdev help"
net: Move error reporting from net_init_client/netdev to the calling site
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The legacy "-net" option can be quite confusing for the users since most
people do not expect to get a "vlan" hub between their emulated guest
hardware and the host backend. But so far, we are also not able to get
rid of "-net" completely, since it is the only way to configure on-board
NICs that can not be instantiated via "-device" yet. It's also a little
bit shorter to type "-net nic -net tap" instead of "-device xyz,netdev=n1
-netdev tap,id=n1".
So what we need is a new convenience option that is shorter to type than
the full -device + -netdev stuff, and which can be used to configure the
on-board NICs that can not be handled via -device yet. Thus this patch now
provides such a new option "--nic": It adds an entry in the nd_table to
configure a on-board / default NIC, creates a host backend and connects
the two directly, without a confusing "vlan" hub inbetween.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
Impliment the vhost-crypto's funtions, such as startup,
stop and notification etc. Introduce an enum
QCryptoCryptoDevBackendOptionsType in order to
identify the cryptodev vhost backend is vhost-user
or vhost-kernel-module (If exist).
At this point, the cryptdoev-vhost-user works.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently only file backed memory backend can
be created with a "share" flag in order to allow
sharing guest RAM with other processes in the host.
Add the "share" flag also to RAM Memory Backend
in order to allow remapping parts of the guest RAM
to different host virtual addresses. This is needed
by the RDMA devices in order to remap non-contiguous
QEMU virtual addresses to a contiguous virtual address range.
Moved the "share" flag to the Host Memory base class,
modified phys_mem_alloc to include the new parameter
and a new interface memory_region_init_ram_shared_nomigrate.
There are no functional changes if the new flag is not used.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Since HAX_VM_IOCTL_ALLOC_RAM takes a 32-bit size, it cannot handle
RAM blocks of 4GB or larger, which is why HAXM can only run guests
with less than 4GB of RAM. Solve this problem by utilizing the new
HAXM API, HAX_VM_IOCTL_ADD_RAMBLOCK, which takes a 64-bit size, to
register RAM blocks with the HAXM kernel module. The new API is
first added in HAXM 7.0.0, and its availablility and be confirmed
by the presence of the HAX_CAP_64BIT_RAMBLOCK capability flag.
When the guest RAM size reaches 7GB, QEMU will ask HAXM to set up a
memory mapping that covers a 4GB region, which will fail, because
HAX_VM_IOCTL_SET_RAM also takes a 32-bit size. Work around this
limitation by splitting the large mapping into small ones and
calling HAX_VM_IOCTL_SET_RAM multiple times.
Bug: https://bugs.launchpad.net/qemu/+bug/1735576
Signed-off-by: Yu Ning <yu.ning@intel.com>
Message-Id: <1515752555-12784-1-git-send-email-yu.ning@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
This cleanup makes the number of objects depending on qapi/qmp/qdict.h
drop from 4550 (out of 4743) to 368 in my "build everything" tree.
For qapi/qmp/qobject.h, the number drops from 4552 to 390.
While there, separate #include from file comment with a blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-13-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-4-armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the change
to target/s390x/gen-features.c manually reverted, and blank lines
around deletions collapsed.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-3-armbru@redhat.com>
Allow block driver to map and unmap a buffer for later I/O, as a performance
hint.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180116060901.17413-5-famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Implements the WHPX accelerator cpu enlightenments to actually use the whpx-all
accelerator on Windows platforms.
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Message-Id: <1516655269-1785-5-git-send-email-juterry@microsoft.com>
[Register/unregister VCPU thread with RCU. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adds support for the Windows Hypervisor Platform accelerator (WHPX) stubs and
introduces the whpx.h sysemu API for managing the vcpu scheduling and
management.
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Message-Id: <1516655269-1785-3-git-send-email-juterry@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the addition of default-configs/hppa-softmmu.mak, this
will compile. It is not enabled with this patch, however.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.
The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.
The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)
Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Use an Error** for request to let the caller handle error reporting.
This will also allow to inform the frontend of a backend error.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The TPM backend uses a GThreadPool to handle IO in a seperate
thread. However, GThreadPool isn't integrated with Qemu main loops,
making it unnecessarily complicated to deal with.
Qemu has a AIO threadpool, that is better integrated with loops and
various IO functions, provides completion BH by default etc.
Remove the only user of GThreadPool from qemu, use AIO threadpool.
Note that the backend:
- no longer accepts queing multiple requests (unneeded so far)
- increase ref to itself when handling a command, for extra safety
- tpm_backend_thread_end() is renamed tpm_backend_finish_sync() and
will wait for completion of BH (request_completed), which will help
migration handling.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Drop no_frame flag from sdl_display_init argument list, use a global
variable instead. This is temporary until -no-frame support is dropped
altogether when we remove sdl1 support.
Remove any traces of noframe from sdl2 code. It is just dead code as
sdl2 doesn't support the SDL_NOFRAME window flag any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180115154855.30850-3-kraxel@redhat.com
This patch implements setting the tracking of dirty vga pages, using hvf's
interface to protect guest memory. It uses the MemoryListener callback
mechanism through .log_start/stop/sync
Signed-off-by: Sergio Andres Gomez Del Real <Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-13-Sergio.G.DelReal@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This file begins tracking the files that will be the code base for HVF
support in QEMU. This code base is part of Google's QEMU version of
their Android emulator, and can be found at
https://android.googlesource.com/platform/external/qemu/+/emu-master-dev
This code is based on Veertu Inc's vdhh (Veertu Desktop Hosted
Hypervisor), found at https://github.com/veertuinc/vdhh. Everything is
appropriately licensed under GPL v2-or-later, except for the code inside
x86_task.c and x86_task.h, which, deriving from KVM (the Linux kernel),
is licensed GPL v2-only.
This code base already implements a very great deal of functionality,
although Google's version removed from Vertuu's the support for APIC
page and hyperv-related stuff. According to the Android Emulator Release
Notes, Revision 26.1.3 (August 2017), "Hypervisor.framework is now
enabled by default on macOS for 32-bit x86 images to improve performance
and macOS compatibility", although we better use with caution for, as the
same Revision warns us, "If you experience issues with it specifically,
please file a bug report...". The code hasn't seen much update in the
last 5 months, so I think that we can further develop the code with
occasional visiting Google's repository to see if there has been any
update.
On top of Google's code, the following changes were made:
- add code to the configure script to support the --enable-hvf argument.
If the OS is Darwin, it checks for presence of HVF in the system. The
patch also adds strings related to HVF in the file qemu-options.hx.
QEMU will only support the modern syntax style '-M accel=hvf' no enable
hvf; the legacy '-enable-hvf' will not be supported.
- fix styling issues
- add glue code to cpus.c
- move HVFX86EmulatorState field to CPUX86State, changing the
the emulation functions to have a parameter with signature 'CPUX86State *'
instead of 'CPUState *' so we don't have to get the 'env'.
Signed-off-by: Sergio Andres Gomez Del Real <Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-2-Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-3-Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-5-Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-6-Sergio.G.DelReal@gmail.com>
Message-Id: <20170905035457.3753-7-Sergio.G.DelReal@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a small chance that iothread_stop() hangs as follows:
Thread 3 (Thread 0x7f63eba5f700 (LWP 16105)):
#0 0x00007f64012c09b6 in ppoll () at /lib64/libc.so.6
#1 0x000055959992eac9 in ppoll (__ss=0x0, __timeout=0x0, __nfds=<optimized out>, __fds=<optimized out>) at /usr/include/bits/poll2.h:77
#2 0x000055959992eac9 in qemu_poll_ns (fds=<optimized out>, nfds=<optimized out>, timeout=<optimized out>) at util/qemu-timer.c:322
#3 0x0000559599930711 in aio_poll (ctx=0x55959bdb83c0, blocking=blocking@entry=true) at util/aio-posix.c:629
#4 0x00005595996806fe in iothread_run (opaque=0x55959bd78400) at iothread.c:59
#5 0x00007f640159f609 in start_thread () at /lib64/libpthread.so.0
#6 0x00007f64012cce6f in clone () at /lib64/libc.so.6
Thread 1 (Thread 0x7f640b45b280 (LWP 16103)):
#0 0x00007f64015a0b6d in pthread_join () at /lib64/libpthread.so.0
#1 0x00005595999332ef in qemu_thread_join (thread=<optimized out>) at util/qemu-thread-posix.c:547
#2 0x00005595996808ae in iothread_stop (iothread=<optimized out>) at iothread.c:91
#3 0x000055959968094d in iothread_stop_iter (object=<optimized out>, opaque=<optimized out>) at iothread.c:102
#4 0x0000559599857d97 in do_object_child_foreach (obj=obj@entry=0x55959bdb8100, fn=fn@entry=0x559599680930 <iothread_stop_iter>, opaque=opaque@entry=0x0, recurse=recurse@entry=false) at qom/object.c:852
#5 0x0000559599859477 in object_child_foreach (obj=obj@entry=0x55959bdb8100, fn=fn@entry=0x559599680930 <iothread_stop_iter>, opaque=opaque@entry=0x0) at qom/object.c:867
#6 0x0000559599680a6e in iothread_stop_all () at iothread.c:341
#7 0x000055959955b1d5 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at vl.c:4913
The relevant code from iothread_run() is:
while (!atomic_read(&iothread->stopping)) {
aio_poll(iothread->ctx, true);
and iothread_stop():
iothread->stopping = true;
aio_notify(iothread->ctx);
...
qemu_thread_join(&iothread->thread);
The following scenario can occur:
1. IOThread:
while (!atomic_read(&iothread->stopping)) -> stopping=false
2. Main loop:
iothread->stopping = true;
aio_notify(iothread->ctx);
3. IOThread:
aio_poll(iothread->ctx, true); -> hang
The bug is explained by the AioContext->notify_me doc comments:
"If this field is 0, everything (file descriptors, bottom halves,
timers) will be re-evaluated before the next blocking poll(), thus the
event_notifier_set call can be skipped."
The problem is that "everything" does not include checking
iothread->stopping. This means iothread_run() will block in aio_poll()
if aio_notify() was called just before aio_poll().
This patch fixes the hang by replacing aio_notify() with
aio_bh_schedule_oneshot(). This makes aio_poll() or g_main_loop_run()
to return.
Implementing this properly required a new bool running flag. The new
flag prevents races that are tricky if we try to use iothread->stopping.
Now iothread->stopping is purely for iothread_stop() and
iothread->running is purely for the iothread_run() thread.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20171207201320.19284-6-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Encapsulate IOThread QOM object lookup so that callers don't need to
know how and where IOThread objects live.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20171206144550.22295-8-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaM1MfAAoJEHWtZYAqC0IRAj8H/AgVHuAf5huzKZkju/OwQ4z0
MxQwNFHbBgT5reRCjK3JAxTviOHUR7JTVLFFyLIbHQDX+VRDoxXWsuVPNdAgd8SF
bA/ywmKlQcYJrdyf1Fole4JY+ZIndkgtUJnwuvC4LWmt/s7LYsNlwOfnARkvtpul
0QH+mlJYv+EeEIjeJDNlgcqxFo4qr8HfuJi2/qC7IEXIHcTYNpdk6gh7auCUVvGl
tojocW0Da0G0Ce1ncFIME9doWlBu0ZiU+b3mjjDf5OVtXiT6Xce3o9bNTWsboHia
iuvyEaFU/wXbHkn+i/50/DIP6o+u9wJ4MmYp3uJKlpen0SZndZ+UFxcBY7ZrP4g=
=s0pV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2017-12-15-1' into staging
Merge tpm 2017/12/15 v1
# gpg: Signature made Fri 15 Dec 2017 04:44:15 GMT
# gpg: using RSA key 0x75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2017-12-15-1: (32 commits)
tpm: tpm_passthrough: Fail startup if FE buffer size < BE buffer size
tpm: tpm_emulator: get and set buffer size of device
tpm: tpm_passthrough: Read the buffer size from the host device
tpm: pull tpm_util_request() out of tpm_util_test()
tpm: Move getting TPM buffer size to backends
tpm: remove tpm_register_model()
tpm-tis: use DEFINE_PROP_TPMBE
qdev: add DEFINE_PROP_TPMBE
tpm-tis: check that at most one TPM device exists
tpm-tis: remove redundant 'tpm_tis:' in error messages
tpm-emulator: add a FIXME comment about blocking cancel
acpi: change TPM TIS data conditions
tpm: add tpm_cmd_get_size() to tpm_util
tpm: add TPM interface to lookup TPM version
tpm: lookup the the TPM interface instead of TIS device
tpm: rename qemu_find_tpm() -> qemu_find_tpm_be()
tpm-tis: simplify header inclusion
tpm-passthrough: workaround a possible race
tpm-passthrough: simplify create()
tpm-passthrough: make it safer to destroy after creation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the tpm_emulator backend to get the current buffer size
of the external device and set it to the buffer size that the
frontend (TIS) requests.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Rather than setting the size of the TPM buffer in the front-end,
query the backend for the size of the buffer. In this patch we
just move the hard-coded buffer size of 4096 to the backends.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The device should be exposed if present. It shouldn't have an
undefined version (or else backend init failed, and device should fail
too). Finally, make the fields specific to TIS device model.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Do not hardcode TPM device model to lookup version, use an interface
instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This will allow to introduce new devices implementing TPM.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
find_tpm() will be introduced to lookup the TPM device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
QEMU code doesn't generally have assert() for mandatory
callbacks/function pointers, probably because the crash is pretty
obvious. Document the methods instead of going into the code.
Make get_tpm_options() mandatory to implement (since all
backend implementation have it).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
No need to store the mode in the backend, or to let the frontend set
it itself.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Backend can give more accurate error description, and lift out the job
from the frontend.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Lift from the backend implementation the responsability to call the
request_completed() callback outside of thread context. This also
simplify frontend/interface work, as they no longer need to care
whether the callback is called from a different thread.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Now that there is an interface instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Store the TPM interface, the actual object may be different from
TPMState. Keep a reference on the interface, and check the backend
wasn't already initialized.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This is a better location than hw/tpm, since we are going to use the
interface from outside hw/tpm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
SPAPR is the last user of numa_get_node() and a bunch of
supporting code to maintain numa_info[x].addr list.
Get LMB node id from pc-dimm list, which allows to
remove ~80LOC maintaining dynamic address range
lookup list.
It also removes pc-dimm dependency on numa_[un]set_mem_node_id()
and makes pc-dimms a sole source of information about which
node it belongs to and removes duplicate data from global
numa_info.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It's easy to use device_add and device_del as replacement instead.
The usb_add and usb_del commands are deprecated since QEMU 2.10,
and nobody complained that they are still needed, so let's get rid
of them now to make the HMP interface a little bit less overloaded.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1512073140-17672-1-git-send-email-thuth@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
else file including "sysemu/tpm.h" fails to compile:
In file included from qemu/stubs/tpm.c:2:0:
qemu/include/sysemu/tpm.h:36:19: error: implicit declaration of function ‘object_resolve_path_type’ [-Werror=implicit-function-declaration]
Object *obj = object_resolve_path_type("", TYPE_TPM_TIS, NULL);
^~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This simplifies a bit locality handling, and argument passing, and
could pave the way to queuing requests (if that makes sense).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The tpm_state is passed as argument, the assert() is pointless since
we give it the value of tpm_state->locty_number already.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
There is only handling of request so far in both backends.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
No backend use it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Use TPMBackendClass to hold class methods/fields.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Close to where it's being used.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
No more users of be_drivers[], drop that too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
No need to export the function.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
A bunch of fixes all over the place.
A new vmcore device - the user interface around it is still somewhat
controversial, but I feel most of the code is fine, suggestions can be
addressed by adding patches on top.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ4s+/AAoJECgfDbjSjVRpHQMH/2fVQ9b70BvG4KFpzwhIT3dg
eyglA9NsXTVINcGu598ZoBD+1OF1N23o6SpcOd56nyLnBwAWiwfnOk05Ncx7WQ4g
VZoxWcpzrG6SO1Hczg4y1EfT1+cIhlaf3a0kuVGmDTb/zPdMwAqAzw0rjvY5uIjY
wixOWXfJ34Tq8PNrFIaWECuI5Php+QVTNnvvKQTzgWn1iksj1a4pdZb6/Jd5SLFY
6hjtfZccDSsqeOduoJMJGJ2pHLbZEaqpxzPBM/AVW0BdWTpeOPI12SazZwUfEcLe
uHoIASknekX9E6U57l0syRHlvBTnaZkJ0YIw4e3Z08qPBYOL8eFr+M8kjHaIIxc=
=yEmz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: fixes, features
A bunch of fixes all over the place.
A new vmcore device - the user interface around it is still somewhat
controversial, but I feel most of the code is fine, suggestions can be
addressed by adding patches on top.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 15 Oct 2017 04:02:23 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
tests/pxe: Test more NICs when running in SPEED=slow mode
pc: remove useless hot_add_cpu initialisation
isapc: Remove unnecessary migration compatibility code
virtio-pci: Replace modern_as with direct access to modern_bar
virtio: fix descriptor counting in virtqueue_pop
hw/gen_pcie_root_port: make IO RO 0 on IO disabled
pci: Validate interfaces on base_class_init
xen/pt: Mark TYPE_XEN_PT_DEVICE as hybrid
pci: Add INTERFACE_CONVENTIONAL_PCI_DEVICE to Conventional PCI devices
pci: Add INTERFACE_PCIE_DEVICE to all PCIe devices
pci: Add interface names to hybrid PCI devices
pci: conventional-pci-device and pci-express-device interfaces
PCI: PCIe access should always be little endian
virtio/pci/migration: Convert to VMState
hw/pci-bridge/pcie_pci_bridge: properly handle MSI unavailability case
pci: allow 32-bit PCI IO accesses to pass through the PCI bridge
virtio/vhost: reset dev->log after syncing
MAINTAINERS: add Dump maintainers
scripts/dump-guest-memory.py: add vmcoreinfo
kdump: set vmcoreinfo location
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read the guest ELF PT_NOTE from guest memory when fw_cfg
etc/vmcoreinfo entry provides the location, and write it as an
additional note in the dump.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
buffer reallocation is very unlikely to be backend specific. Hence move inside
the tis.
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
TPM configuration options are backend implementation details and shall not be
part of base TPMBackend object, and these shall not be accessed directly outside
of the class, hence added a new interface method, get_tpm_options() to
TPMDriverOps., which shall be implemented by the derived classes to return
configured tpm options.
A new tpm backend api - tpm_backend_query_tpm() which uses _get_tpm_options() to
prepare TpmInfo.
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This allows backend implementations left optional interface methods.
For mandatory methods assertion checks added.
Took the opportunity to remove unused methods:
- tpm_backend_get_desc()
- TPMDriverOps->handle_startup_error
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger<stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Initialize and free TPMBackend data members in it's own instance_init() and
instance_finalize methods.
Took the opportunity to remove unneeded destroy() method from TpmDriverOps
interface as TPMBackend is a Qemu Object, we can use object_unref() inplace of
tpm_backend_destroy() to free the backend object, hence removed destroy() from
TPMDriverOps interface.
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Move thread handling inside TPMBackend, this way backend implementations need
not to maintain their own thread life cycle, instead they needs to implement
'handle_request()' class method that always been called from a thread.
This change made tpm_backend_int.h kind of useless, hence removed it.
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
TPMDriverOps inside TPMBackend is not required, as it is supposed to be a class
member. The only possible reason for keeping in TPMBackend was, to get the
backend type in tpm.c where dedicated backend api, tpm_backend_get_type() is
present.
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
So that internal iothread users can explicitly stop one iothread without
destroying it.
Since at it, fix iothread_stop() to allow it to be called multiple
times. Before this patch we may call iothread_stop() more than once on
single iothread, while that may not be correct since qemu_thread_join()
is not allowed to run twice. From manual of pthread_join():
Joining with a thread that has previously been joined results in
undefined behavior.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 20170928025958.1420-4-peterx@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IOThread is a general framework that contains IO loop environment and a
real thread behind. It's also good to be used internally inside qemu.
Provide some helpers for it to create iothreads to be used internally.
Put all the internal used iothreads into the internal object container.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 20170928025958.1420-3-peterx@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
On a server-class ppc host, this capability depends on the KVM type,
ie, HV or PR. If both KVM are present in the kernel, we will always
get the HV specific value, even if we explicitely requested PR on
the command line.
This can have an impact if we're using hugepages or a balloon device.
Since we've already created the VM at the time any user calls
kvm_has_sync_mmu(), switching to kvm_vm_check_extension() is
enough to fix any potential issue.
It is okay for the other archs that also implement KVM_CAP_SYNC_MMU,
ie, mips, s390, x86 and arm, because they don't depend on the VM being
created or not.
While here, let's cache the state of this extension in a bool variable,
since it has several users in the code, as suggested by Thomas Huth.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <150600965332.30533.14702405809647835716.stgit@bahia.lan>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We already have enum that enumerates all the actions that a
watchdog can take when hitting its timeout: WatchdogAction.
Use that instead of inventing our own.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <ce2790634e6a1b3b6cf90462399d17bad83f0290.1504771369.git.mprivozn@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The only prototype doesn't need anything from the lib header, and not
including it here allows files that include this header, for example
vl.c, to compile without the libseccomp cflags.
The breakage is since c3883e1f93 for environments where `pkg-config
--cflags libseccomp" is non-empty.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Eduardo Otubo <otubo@redhat.com>
Message-id: 20170920083647.14599-1-famz@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds [,resourcecontrol=deny] to `-sandbox on' option. It
blacklists all process affinity and scheduler priority system calls to
avoid any bigger of the process.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
This patch adds [,spawn=deny] argument to `-sandbox on' option. It
blacklists fork and execve system calls, avoiding Qemu to spawn new
threads or processes.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
This patch introduces the new argument
[,elevateprivileges=allow|deny|children] to the `-sandbox on'. It allows
or denies Qemu process to elevate its privileges by blacklisting all
set*uid|gid system calls. The 'children' option will let forks and
execves run unprivileged.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
This patch introduces the argument [,obsolete=allow] to the `-sandbox on'
option. It allows Qemu to run safely on old system that still relies on
old system calls.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
This patch changes the default behavior of the seccomp filter from
whitelist to blacklist. By default now all system calls are allowed and
a small black list of definitely forbidden ones was created.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Report amount of hotplugged memory in addition to total
amount per NUMA node.
Signed-off-by: Vadim Galitsyn <vadim.galitsyn@profitbricks.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: qemu-devel@nongnu.org
Message-Id: <20170829153022.27004-2-vadim.galitsyn@profitbricks.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
IOThread uses AioContext event loop and does not run a GMainContext.
Therefore,chardev cannot work in IOThread,such as the chardev is
used for colo-compare packets reception.
This patch makes the IOThread run the GMainContext event loop,
chardev and IOThread can work together.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Wang Yong <wang.yong155@zte.com.cn>
Signed-off-by: Wang Guang <wang.guang55@zte.com.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This commit eliminates the 1:1 relationship between BlockBackend and
throttle group state. Users will be able to create multiple throttle
nodes, each with its own throttle group state, in the future. The
throttle group state cannot be per-BlockBackend anymore, it must be
per-throttle node. This is done by gathering ThrottleGroup membership
details from BlockBackendPublic into ThrottleGroupMember and refactoring
existing code to use the structure.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We have a strict separation between enum TpmModel and tpm_models[]:
* TpmModel may have any number of members. It just happens to have one.
* tpm_register_model() uses the first empty slot in tpm_models[].
If you register more than tpm_models[] has space,
tpn_register_model() fails. Its caller silently ignores the
failure.
Register the same TpmModel more than once has no effect other than
wasting tpm_models[] slots: tpm_model_is_registered() is happy with
the first one it finds.
Since we only ever register one model, and tpm_models[] has space for
just that one, this contraption even works.
Turn tpm_models[] into a straight map from enum TpmType to bool. Much
simpler.
Cc: Stefan Berger <stefanb@us.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-5-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[Commit message typo fixed]
We have a strict separation between enum TpmType and be_drivers[]:
* TpmType may have any number of members. It just happens to have one.
* tpm_register_driver() uses the first empty slot in be_drivers[].
If you register more than tpm_models[] has space,
tpm_register_driver() fails. Its caller silently ignores the
failure.
If you register more than one with a given TpmType,
tpm_display_backend_drivers() will shows all of them, but
tpm_driver_find_by_type() and tpm_get_backend_driver() will find
only the one one that registered first.
Since we only ever register one driver, and be_drivers[] has space for
just that one, this contraption even works.
Turn be_drivers[] into a straight map from enum TpmType to driver.
Much simpler, and has a decent chance to actually work should we ever
acquire additional drivers.
While there, use qapi_enum_parse() in tpm_get_backend_driver().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170822132255.23945-8-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, superfluous initializer dropped, commit message rewritten]
Cc: Stefan Berger <stefanb@us.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-4-git-send-email-armbru@redhat.com>
These two conditions corresponds to mirror job's source and target,
which need to be allowed as they are part of the non-shared storage
migration workflow: failing to inactivate either will result in a
failure during migration completion.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170823134242.12080-3-famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[eblake: improve comment grammar]
Signed-off-by: Eric Blake <eblake@redhat.com>
Building QEMU on fedora26 with the latest gcc package fails:
CC ppc64-softmmu/target/ppc/kvm.o
In file included from include/sysemu/hw_accel.h:16:0,
from target/ppc/kvm.c:31:
target/ppc/kvm.c: In function ‘kvmppc_booke_watchdog_enable’:
include/sysemu/kvm.h:449:35: error: ‘args_tmp[i]’ may be used uninitialized
in this function [-Werror=maybe-uninitialized]
cap.args[i] = args_tmp[i]; \
^
target/ppc/kvm.c: In function ‘kvmppc_set_papr’:
include/sysemu/kvm.h:449:35: error: ‘args_tmp[i]’ may be used uninitialized
in this function [-Werror=maybe-uninitialized]
cc1: all warnings being treated as errors
$ rpm -q gcc
gcc-7.1.1-3.fc26.ppc64le
The compiler should obviously optimize this code away when no extra
agument is passed to kvm_vm_enable_cap() and kvm_vcpu_enable_cap(),
but it doesn't. This bug should be fixed one day in gcc, but we can
also change our code pattern so that we don't hit the issue anymore.
We workaround this, by using memcpy() instead of open-coding the copy.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <150210580404.1343.7325713896658799315.stgit@bahia.lan>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This new call is trying to update a requested map cache entry
according to the changes in the physmap. The call is searching
for the entry, unmaps it and maps again at the same place using
a new guest address. If the mapping is dummy this call will
make it real.
This function makes use of a new xenforeignmemory_map2() call
with an extended interface that was recently introduced in
libxenforeignmemory [1].
[1] https://www.mail-archive.com/xen-devel@lists.xen.org/msg113007.html
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
blk_truncate() itself will pass that value to bdrv_truncate(), and all
callers of blk_truncate() just set the parameter to PREALLOC_MODE_OFF
for now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CONFIG_KVM is only defined for target-specific code, so nobody should
use it by accident in common code. To avoid such subtle bugs,
CONFIG_KVM is now marked as poisoned in common code. The header
include/sysemu/kvm.h is somewhat special since it is included
all over the place from common code, too, so we need some extra
logic via "#ifdef NEED_CPU_H" here to make sure that we can
compile all files without problems.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1498454578-18709-4-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pc.h and sysemu/kvm.h are also included from common code (where
CONFIG_KVM is not available), so the #defines that depend on CONFIG_KVM
should not be declared here to avoid that anybody is using them in a
wrong way. Since we're also going to poison CONFIG_KVM for common code,
let's move them to kvm_i386.h instead. Most of the dummy definitions
from sysemu/kvm.h are also unused since the code that uses them is
only compiled for CONFIG_KVM (e.g. target/i386/kvm.c), so the unused
defines are also simply dropped here instead of being moved.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1498454578-18709-3-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One less global variable, and it does only matter with migration.
We keep the old "--only-migratable" option, but also now we support:
-global migration.only-migratable=true
Currently still keep the old interface.
Hmm, now vl.c has no way to access migrate_get_current(). Export a
function for it to setup only_migratable.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-7-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce this new field for the accelerator classes so that each
specific accelerator in the future can register its own global
properties to be used further by the system. It works just like how the
old machine compatible properties do, but only tailored for
accelerators.
Introduce register_compat_props_array() for it. Export it so that it may
be used in other codes as well in the future.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-3-git-send-email-peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Change the 'int count' parameter in *pwrite_zeros, *pdiscard related
functions (and some others) to 'int bytes', as they both refer to bytes.
This helps with code legibility.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Message-id: 20170609101808.13506-1-el13635@mail.ntua.gr
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Another possibility is to use tg->lock, which we're holding anyway in
both schedule_next_request and throttle_group_co_io_limits_intercept.
This would require open-coding the CoQueue however, so I've chosen this
alternative.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170605123908.18777-10-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
In some circumstances, we don't want to abort if the
kvm_device_access fails. This will be the case during ITS
migration, in case the ITS table save/restore fails because
the guest did not program the vITS correctly. So let's pass an
error object to the function and return the ioctl value. New
callers will be able to make a decision upon this returned
value.
Existing callers pass &error_abort which will cause the
function to abort on failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 1497023553-18411-2-git-send-email-eric.auger@redhat.com
[PMM: wrapped long line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accumulated patches for ppc targets and the pseries machine type.
The big thing in this batch is a start on a substantial cleanup of the
pseries hotplug mechanisms, which were pretty confusing. For now
these shouldn't cause substantial behavioural changes, but I am hoping
these lead to clearer code and eventually to fixes for the bugs we
have in hotplug handling, particularly when hotplug and migration are
combined.
The remaining patches are mostly bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QDWB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.10-20170606' into staging
ppc patch queue 2017-06-06
Accumulated patches for ppc targets and the pseries machine type.
The big thing in this batch is a start on a substantial cleanup of the
pseries hotplug mechanisms, which were pretty confusing. For now
these shouldn't cause substantial behavioural changes, but I am hoping
these lead to clearer code and eventually to fixes for the bugs we
have in hotplug handling, particularly when hotplug and migration are
combined.
The remaining patches are mostly bugfixes.
# gpg: Signature made Tue 06 Jun 2017 03:48:50 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.10-20170606:
spapr: Remove some non-useful properties on DRC objects
spapr: Eliminate spapr_drc_get_type_str()
spapr: Move configure-connector state into DRC
spapr: Clean up spapr_dr_connector_by_*()
spapr: Introduce DRC subclasses
spapr/drc: don't migrate DRC of cold-plugged CPUs and LMBs
spapr: Allow boot from vhost-*-scsi backends
ppc/pnv: check the return value of fdt_setprop()
spapr_nvram: Check return value from blk_getlength()
target/ppc: Fixup set_spr error in h_register_process_table
target-ppc: Fix openpic timer read register offset
spapr: Make DRC get_index and get_type methods into plain functions
spapr: Abolish DRC set_configured method
spapr: Abolish DRC get_fdt method
spapr: Move DRC RTAS calls into spapr_drc.c
migration: Mark CPU states dirty before incoming migration/loadvm
migration: remove register_savevm()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As a rule, CPU internal state should never be updated when
!cpu->kvm_vcpu_dirty (or the HAX equivalent). If that is done, then
subsequent calls to cpu_synchronize_state() - usually safe and idempotent -
will clobber state.
However, we routinely do this during a loadvm or incoming migration.
Usually this is called shortly after a reset, which will clear all the cpu
dirty flags with cpu_synchronize_all_post_reset(). Nothing is expected
to set the dirty flags again before the cpu state is loaded from the
incoming stream.
This means that it isn't safe to call cpu_synchronize_state() from a
post_load handler, which is non-obvious and potentially inconvenient.
We could cpu_synchronize_all_state() before the loadvm, but that would be
overkill since a) we expect the state to already be synchronized from the
reset and b) we expect to completely rewrite the state with a call to
cpu_synchronize_all_post_init() at the end of qemu_loadvm_state().
To clear this up, this patch introduces cpu_synchronize_pre_loadvm() and
associated helpers, which simply marks the cpu state as dirty without
actually changing anything. i.e. it says we want to discard any existing
KVM (or HAX) state and replace it with what we're going to load.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dave Gilbert <dgilbert@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>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=5eL6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chrfe-pull-request' into staging
# gpg: Signature made Fri 02 Jun 2017 20:12:48 BST
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chrfe-pull-request:
char: move char devices to chardev/
char: make chr_fe_deinit() optionaly delete backend
char: rename functions that are not part of fe
char: move CharBackend handling in char-fe unit
char: generalize qemu_chr_write_all()
be-hci: use backend functions
chardev: serial & parallel declaration to own headers
chardev: move headers to include/chardev
Remove/replace sysemu/char.h inclusion
char-win: close file handle except with console
char-win: rename hcom->file
char-win: rename win_chr_init/poll win_chr_serial_init/poll
char-win: remove WinChardev.len
char-win: simplify win_chr_read()
char: cast ARRAY_SIZE() as signed to silent warning on empty array
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So they are all in one place. The following patch will move serial &
parallel declarations to the respective headers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Start removing migration code from sysemu/sysemu.h.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
mapped-file security mode (especially for the virtfs root).
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAlktdVYACgkQAvw66wEB28LaTgCfS/bunOy4Wp+I+DO/Gx/5bfNp
7/IAn3qfJYBqRnpfz8KNKRZJ8QG/Bu5X
=KTTf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
Various bugfixes and code cleanups. Most notably, it fixes metadata handling in
mapped-file security mode (especially for the virtfs root).
# gpg: Signature made Tue 30 May 2017 14:36:22 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "[jpeg image of size 3330]"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9pfs: local: metadata file for the VirtFS root
9pfs: local: simplify file opening
9pfs: local: resolve special directories in paths
9pfs: check return value of v9fs_co_name_to_path()
util: drop old utimensat() compat code
9pfs: assume utimensat() and futimens() are present
fsdev: fix virtfs-proxy-helper cwd
9pfs: local: fix unlink of alien files in mapped-file mode
9pfs: drop pdu_push_and_notify()
fsdev: don't allow unknown format in marshal/unmarshal
virtio-9p/xen-9p: move 9p specific bits to core 9p code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This removes last trace of migration functions from sysemu/sysemu.h.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Now that 9pfs and virtfs-proxy-helper have been converted to utimensat(),
we don't need to keep qemu_utimens() anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Libvirt would like to be able to distinguish between a SHUTDOWN
event triggered solely by guest request and one triggered by a
SIGTERM or other action on the host. While qemu_kill_report() was
already able to give different output to stderr based on whether a
shutdown was triggered by a host signal (but NOT by a host UI event,
such as clicking the X on the window), that information was then
lost to management. The previous patches improved things to use an
enum throughout all callsites, so now we have something ready to
expose through QMP.
Note that for now, the decision was to expose ONLY a boolean,
rather than promoting ShutdownCause to a QAPI enum; this is because
libvirt has not expressed an interest in anything finer-grained.
We can still add additional details, in a backwards-compatible
manner, if a need later arises (if the addition happens before 2.10,
we can replace the bool with an enum; otherwise, the enum will have
to be in addition to the bool); this patch merely adds a helper
shutdown_caused_by_guest() to map the internal enum into the
external boolean.
Update expected iotest outputs to match the new data (complete
coverage of the affected tests is obtained by -raw, -qcow2, and -nbd).
Here is output from 'virsh qemu-monitor-event --loop' with the
patch installed:
event SHUTDOWN at 1492639680.731251 for domain fedora_13: {"guest":true}
event STOP at 1492639680.732116 for domain fedora_13: <null>
event SHUTDOWN at 1492639680.732830 for domain fedora_13: {"guest":false}
Note that libvirt runs qemu with -no-shutdown: the first SHUTDOWN event
was triggered by an action I took directly in the guest (shutdown -h),
at which point qemu stops the vcpus and waits for libvirt to do any
final cleanups; the second SHUTDOWN event is the result of libvirt
sending SIGTERM now that it has completed cleanup. Libvirt is already
smart enough to only feed the first qemu SHUTDOWN event to the end user
(remember, virsh qemu-monitor-event is a low-level debugging interface
that is explicitly unsupported by libvirt, so it sees things that normal
end users do not); changing qemu to emit SHUTDOWN only once is outside
the scope of this series.
See also https://bugzilla.redhat.com/1384007
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170515214114.15442-6-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
With the recent addition of ShutdownCause, we want to be able to pass
a cause through any shutdown request, and then faithfully replay that
cause when later replaying the same sequence. The easiest way is to
expand the reply event mechanism to track a series of values for
EVENT_SHUTDOWN, one corresponding to each value of ShutdownCause.
We are free to change the replay stream as needed, since there are
already no guarantees about being able to use a replay stream by
any other version of qemu than the one that generated it.
The cause is not actually fed back until the next patch changes the
signature for requesting a shutdown; a TODO marks that upcoming change.
Yes, this uses the gcc/clang extension of a ranged case label,
but this is not the first time we've used non-C99 constructs.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170515214114.15442-4-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We want to track why a guest was shutdown; in particular, being able
to tell the difference between a guest request (such as ACPI request)
and host request (such as SIGINT) will prove useful to libvirt.
Since all requests eventually end up changing shutdown_requested in
vl.c, the logical change is to make that value track the reason,
rather than its current 0/1 contents.
Since command-line options control whether a reset request is turned
into a shutdown request instead, the same treatment is given to
reset_requested.
This patch adds an internal enum ShutdownCause that describes reasons
that a shutdown can be requested, and changes qemu_system_reset() to
pass the reason through, although for now nothing is actually changed
with regards to what gets reported. The enum could be exported via
QAPI at a later date, if deemed necessary, but for now, there has not
been a request to expose that much detail to end clients.
For the most part, we turn 0 into SHUTDOWN_CAUSE_NONE, and 1 into
SHUTDOWN_CAUSE_HOST_ERROR; the only specific case where we have enough
information right now to use a different value is when we are reacting
to a host signal. It will take a further patch to edit all call-sites
that can trigger a reset or shutdown request to properly pass in any
other reasons; this patch includes TODOs to point such places out.
qemu_system_reset() trades its 'bool report' parameter for a
'ShutdownCause reason', with all non-zero values having the same
effect; this lets us get rid of the weird #defines for VMRESET_*
as synonyms for bools.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170515214114.15442-3-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
There's no reason to keep the soundhw table in arch_init.c. Move
that code to a new hw/audio/soundhw.c file.
While moving the code, trivial coding style issues were fixed.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170508205735.23444-2-ehabkost@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
That is the only function that we need from exec.c, and having to
include the whole sysemu.h for this.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
/me leans to be less sloppy with copyright notices
thanks Dave
Not used anymore after moving block migration to use capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The function is only used once, and nothing else in migration knows
about objects. Create the function vmstate_device_is_migratable() in
savem.c that really do the bit that is related with migration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
This way we use the "normal" way of printing errors for hmp commands.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The Xen mapcache is able to create long term mappings, they are called
"locked" mappings. The third parameter of the xen_map_cache call
specifies if a mapping is a "locked" mapping.
>From the QEMU point of view there are two kinds of long term mappings:
[a] device memory mappings, such as option roms and video memory
[b] dma mappings, created by dma_memory_map & friends
After certain operations, ballooning a VM in particular, Xen asks QEMU
kindly to destroy all mappings. However, certainly [a] mappings are
present and cannot be removed. That's not a problem as they are not
affected by balloonning. The *real* problem is that if there are any
mappings of type [b], any outstanding dma operations could fail. This is
a known shortcoming. In other words, when Xen asks QEMU to destroy all
mappings, it is an error if any [b] mappings exist.
However today we have no way of distinguishing [a] from [b]. Because of
that, we cannot even print a decent warning.
This patch introduces a new "dma" bool field to MapCacheRev entires, to
remember if a given mapping is for dma or is a long term device memory
mapping. When xen_invalidate_map_cache is called, we print a warning if
any [b] mappings exist. We ignore [a] mappings.
Mappings created by qemu_map_ram_ptr are assumed to be [a], while
mappings created by address_space_map->qemu_ram_ptr_length are assumed
to be [b].
The goal of the patch is to make debugging and system understanding
easier.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Postfactum "CPU(s) present in multiple NUMA nodes" check
was the last user of node_cpu bitmaps, but it's not need
as machine_set_cpu_numa_node() does the similar check at
the time mapping is set for cpus (i.e. when -numa cpus=
is parsed) and ensures that cpu can be mapped only to
one node.
Remove duplicate check based on node_cpu bitmaps and
since the last user is gone remove node_cpu as well,
which completes internal transition from legacy bitmap
based mapping storage to possible_cpus storage.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1494415802-227633-17-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
CPUState::numa_node is still in use but now it's set by
board when it creates CPU objects. So there isn't any
need to set it again after all CPU's are created,
since it's been already set.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1494415802-227633-14-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Originally CPU threads were by default assigned in
round-robin fashion. However it was causing issues in
guest since CPU threads from the same socket/core could
be placed on different NUMA nodes.
Commit fb43b73b (pc: fix default VCPU to NUMA node mapping)
fixed it by grouping threads within a socket on the same node
introducing cpu_index_to_socket_id() callback and commit
20bb648d (spapr: Fix default NUMA node allocation for threads)
reused callback to fix similar issues for SPAPR machine
even though socket doesn't make much sense there.
As result QEMU ended up having 3 default distribution rules
used by 3 targets /virt-arm, spapr, pc/.
In effort of moving NUMA mapping for CPUs into possible_cpus,
generalize default mapping in numa.c by making boards decide
on default mapping and let them explicitly tell generic
numa code to which node a CPU thread belongs to by replacing
cpu_index_to_socket_id() with @cpu_index_to_instance_props()
which provides default node_id assigned by board to specified
cpu_index.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1494415802-227633-2-git-send-email-imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When there are more nodes than available memory to put the minimum
allowed memory by node, all the memory is put on the last node.
This is because we put (ram_size / nb_numa_nodes) &
~((1 << mc->numa_mem_align_shift) - 1); on each node, and in this
case the value is 0. This is particularly true with pseries,
as the memory must be aligned to 256MB.
To avoid this problem, this patch uses an error diffusion algorithm [1]
to distribute equally the memory on nodes.
We introduce numa_auto_assign_ram() function in MachineClass
to keep compatibility between machine type versions.
The legacy function is used with pseries-2.9, pc-q35-2.9 and
pc-i440fx-2.9 (and previous), the new one with all others.
Example:
qemu-system-ppc64 -S -nographic -nodefaults -monitor stdio -m 1G -smp 8 \
-numa node -numa node -numa node \
-numa node -numa node -numa node
Before:
(qemu) info numa
6 nodes
node 0 cpus: 0 6
node 0 size: 0 MB
node 1 cpus: 1 7
node 1 size: 0 MB
node 2 cpus: 2
node 2 size: 0 MB
node 3 cpus: 3
node 3 size: 0 MB
node 4 cpus: 4
node 4 size: 0 MB
node 5 cpus: 5
node 5 size: 1024 MB
After:
(qemu) info numa
6 nodes
node 0 cpus: 0 6
node 0 size: 0 MB
node 1 cpus: 1 7
node 1 size: 256 MB
node 2 cpus: 2
node 2 size: 0 MB
node 3 cpus: 3
node 3 size: 256 MB
node 4 cpus: 4
node 4 size: 256 MB
node 5 cpus: 5
node 5 size: 256 MB
[1] https://en.wikipedia.org/wiki/Error_diffusion
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170502162955.1610-2-lvivier@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: s/ram_size/size/ at numa_default_auto_assign_ram()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch is going to add SLIT table support in QEMU, and provides
additional option `dist` for command `-numa` to allow user set vNUMA
distance by QEMU command.
With this patch, when a user wants to create a guest that contains
several vNUMA nodes and also wants to set distance among those nodes,
the QEMU command would like:
```
-numa node,nodeid=0,cpus=0 \
-numa node,nodeid=1,cpus=1 \
-numa node,nodeid=2,cpus=2 \
-numa node,nodeid=3,cpus=3 \
-numa dist,src=0,dst=1,val=21 \
-numa dist,src=0,dst=2,val=31 \
-numa dist,src=0,dst=3,val=41 \
-numa dist,src=1,dst=2,val=21 \
-numa dist,src=1,dst=3,val=31 \
-numa dist,src=2,dst=3,val=21 \
```
Signed-off-by: He Chen <he.chen@linux.intel.com>
Message-Id: <1493260558-20728-1-git-send-email-he.chen@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZDE+gAAoJEL/70l94x66DIpYH/1IOz3u8ObD8D4Lor07LkCCZ
vWFnTBMgGi9gTL5JQDnukRR3cmNp9EVOtAP5Yf+v+/Xqyq/FNGnoVWxCxEby7LtN
zrIXbsKMCaEcGzRNJFcbKV+KZnzkJrz92J0NHy29ruCK1AsslOXAWf4Qb1MV+fQl
6w2Upsh35usvWCNpFm2o8arzMEmNuE2xJDPKUB11GMrZT6TExq4Zqa8Zj1Ihc0sX
XcDr+eeBmb65Vv3jQLntOhSWAy0Xxf/fDXYTQx+JLHFgvpSOIWMiS+fqIVXtT0bH
0E4hQrBr0qjes8n8+9WGGQW2k8Ak0QlDvrZnQ97hTeV1k6SxW+2ATO2mLeJp9TM=
=5hf2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'bonzini/tags/for-upstream' into staging
A large set of small patches. I have not included yet vhost-user-scsi,
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
# gpg: Signature made Fri 05 May 2017 06:10:40 AM EDT
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* bonzini/tags/for-upstream: (21 commits)
vhost-scsi: create a vhost-scsi-common abstraction
libvhost-user: replace vasprintf() to fix build
get_maintainer: add subsystem to reviewer output
get_maintainer: --r (list reviewer) is on by default
get_maintainer: it's '--pattern-depth', not '-pattern-depth'
get_maintainer: Teach get_maintainer.pl about the new "R:" tag
MAINTAINERS: Add "R:" tag for self-appointed reviewers
Fix the -accel parameter and the documentation for 'hax'
dump: Acquire BQL around vm_start() in dump thread
hax: Fix memory mapping de-duplication logic
checkpatch: Disallow glib asserts in main code
trace: add qemu mutex lock and unlock trace events
vmw_pvscsi: check message ring page count at initialisation
sgabios: update for "fix wrong video attrs for int 10h,ah==13h"
scsi: avoid an off-by-one error in megasas_mmio_write
vl: deprecate the "-hdachs" option
use _Static_assert in QEMU_BUILD_BUG_ON
target/i386: Add GDB XML register description support
char: Fix removing wrong GSource that be found by fd_in_tag
hw/i386: Build-time assertion on pc/q35 reset register being identical.
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
devices via tn3270. Actual handling of the data stream is
delegated to x3270; more info at http://wiki.qemu.org/Features/3270
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kMb4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'cohuck/tags/s390x-3270-20170504' into staging
Basic support for using channel-attached 3270 'green-screen'
devices via tn3270. Actual handling of the data stream is
delegated to x3270; more info at http://wiki.qemu.org/Features/3270
# gpg: Signature made Thu 04 May 2017 11:36:51 AM BST
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* cohuck/tags/s390x-3270-20170504:
s390x/3270: Mark non-migratable and enable the device
s390x/3270: Detect for continued presence of a 3270 client
s390x/3270: Add the TCP socket events handler for 3270
s390x/3270: 3270 data stream handling
s390x/3270: Add emulated terminal3270 device
s390x/3270: Add abstract emulated ccw-attached 3270 device
s390x/css: Add an algorithm to find a free chpid
chardev: Basic support for TN3270
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes an assertion failure in the following backtrace:
__GI___assert_fail
memory_region_transaction_commit
memory_region_add_eventfd
virtio_pci_ioeventfd_assign
virtio_bus_set_host_notifier
virtio_blk_data_plane_start
virtio_bus_start_ioeventfd
virtio_vmstate_change
vm_state_notify
vm_prepare_start
vm_start
dump_cleanup
dump_process
dump_thread
start_thread
clone
vm_start need BQL, acquire it if doing cleaning up from main thread.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170503072819.14462-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The list is now empty, the chardev cleanup is taken care of by the unref
of the root container.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Add a /chardevs container object to hold the list of chardevs.
(Note: QTAILQ chardevs is going away in the following commits)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The function simply alias and hides the real event function.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This introduces basic support for TN3270, which needs to negotiate
three Telnet options during handshake:
- End of Record
- Binary Transmission
- Terminal-Type
As a basic implementation, this simply ignores NOP and Interrupt
Process(IP) commands. More work should be done for them later.
For more details, please refer to RFC 854 and 1576.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Acked-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
It only uses block/* functions, nothing from migration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It really uses block/* stuff, not migration one.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It is a monitor command, and has nothing migration specific in it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
load_vmstate() already use error_report, so be consistent. There is
an identical error message in load_vmstate() that ends in a
period. Remove it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
For one thing, this allows us to drop the error message generation from
qemu-img.c and blockdev.c and instead have it unified in
bdrv_truncate().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170328205129.15138-3-mreitz@redhat.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
blk_name() is not modifying data passed to it through pointer and it
returns also a pointer to const so the argument can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use the new ioctl, KVM_PPC_GET_RMMU_INFO, to fetch radix MMU
information from KVM and present the page encodings in the device tree
under ibm,processor-radix-AP-encodings. This provides page size
information to the guest which is necessary for it to use radix mode.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[dwg: Compile fix for 32-bit targets, style nit fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----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=EsZ5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20170421' into staging
migration/next for 20170421
# gpg: Signature made Fri 21 Apr 2017 11:28:13 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20170421: (65 commits)
hmp: info migrate_parameters format tunes
hmp: info migrate_capability format tunes
migration: rename max_size to threshold_size
migration: set current_active_state once
virtio-rng: stop virtqueue while the CPU is stopped
migration: don't close a file descriptor while it can be in use
ram: Remove migration_bitmap_extend()
migration: Disable hotplug/unplug during migration
qdev: Move qdev_unplug() to qdev-monitor.c
qdev: Export qdev_hot_removed
qdev: qdev_hotplug is really a bool
migration: Remove MigrationState parameter from migration_is_idle()
ram: Use RAMBitmap type for coherence
ram: rename last_ram_offset() last_ram_pages()
ram: Use ramblock and page offset instead of absolute offset
ram: Change offset field in PageSearchStatus to page
ram: Remember last_page instead of last_offset
ram: Use page number instead of an address for the bitmap operations
ram: reorganize last_sent_block
ram: ram_discard_range() don't use the mis parameter
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It was used as a size in all cases except one.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We were checking this against memory region size of host memory
backend's mr field to see whether the mr has been inited. This is
efficient but less elegant. Let's make a helper for it to avoid
confusions, along with some notes.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1489151370-15453-2-git-send-email-peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Allow block backends to forward drain requests to their devices/users.
The initial intended purpose for this patch is to allow BBs to forward
requests along to BlockJobs, which will want to pause if their associated
BB has entered a drained region.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20170316212351.13797-3-jsnow@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
There is no change for now, because the callback just invokes
qemu_notify_event.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This dependency is the wrong way, and we will need util/qemu-timer.h from
sysemu/cpus.h in the next patch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The definition of the major() and minor() macros are moving within glibc to
<sys/sysmacros.h>. Include this header when it is available to avoid the
following sorts of build-stopping messages:
qga/commands-posix.c: In function ‘dev_major_minor’:
qga/commands-posix.c:656:13: error: In the GNU C Library, "major" is defined
by <sys/sysmacros.h>. For historical compatibility, it is
currently defined by <sys/types.h> as well, but we plan to
remove this soon. To use "major", include <sys/sysmacros.h>
directly. If you did not intend to use a system-defined macro
"major", you should undefine it after including <sys/types.h>. [-Werror]
*devmajor = major(st.st_rdev);
^~~~~~~~~~~~~~~~~~~~~~~~~~
qga/commands-posix.c:657:13: error: In the GNU C Library, "minor" is defined
by <sys/sysmacros.h>. For historical compatibility, it is
currently defined by <sys/types.h> as well, but we plan to
remove this soon. To use "minor", include <sys/sysmacros.h>
directly. If you did not intend to use a system-defined macro
"minor", you should undefine it after including <sys/types.h>. [-Werror]
*devminor = minor(st.st_rdev);
^~~~~~~~~~~~~~~~~~~~~~~~~~
The additional include allows the build to complete on Fedora 26 (Rawhide)
with glibc version 2.24.90.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Call kvm_on_sigbus_vcpu asynchronously from the VCPU thread.
Information for the SIGBUS can be stored in thread-local variables
and processed later in kvm_cpu_exec.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Build it on kvm_arch_on_sigbus_vcpu instead. They do the same
for "action optional" SIGBUSes, and the main thread should never get
"action required" SIGBUSes because it blocks the signal.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds recording and replaying audio data. Is saves synchronization
information for audio out and inputs from the microphone.
v2: removed unneeded whitespace change
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-id: 20170202055054.4848.94901.stgit@PASHA-ISP.lan02.inno
[ kraxel: add qemu/error-report.h include to fix osx build failure ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The HMP command 'qemu-io' is a bit tricky because it wants to work on
the original BlockBackend, but additional permissions could be required.
The details are explained in a comment in the code, but in summary, just
request whatever permissions the current qemu-io command needs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Now that blk_insert_bs() requests the BlockBackend permissions for the
node it attaches to, it can fail. Instead of aborting, pass the errors
to the callers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
The BlockBackend can now store the permissions that its user requires.
This is necessary because nodes can be ejected from or inserted into a
BlockBackend and all of these operations must make sure that the user
still gets what it requested initially.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We know there will be cases where MTTCG won't work until additional work
is done in the front/back ends to support. It will however be useful to
be able to turn it on.
As a result MTTCG will default to off unless the combination is
supported. However the user can turn it on for the sake of testing.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[AJB: move to -accel tcg,thread=multi|single, defaults]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
-----BEGIN PGP SIGNATURE-----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=/97H
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-block-2017-02-21' into staging
Changes to -drive without if= and with if=scsi
# gpg: Signature made Tue 21 Feb 2017 12:22:35 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-block-2017-02-21:
hw/i386: Deprecate -drive if=scsi with PC machine types
hw: Deprecate -drive if=scsi with non-onboard HBAs
hw/scsi: Concentrate -drive if=scsi auto-create in one place
hw: Drop superfluous special checks for orphaned -drive
blockdev: Make orphaned -drive fatal
blockdev: Improve message for orphaned -drive
hw/arm/highbank: Default -drive to if=ide instead of if=scsi
hw: Default -drive to if=none instead of scsi when scsi cannot work
hw: Default -drive to if=none instead of ide when ide cannot work
hw/arm/cubieboard hw/arm/xlnx-ep108: Fix units_per_default_bus
hw: Default -drive to if=ide explicitly where it works
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
If machine initialization code doesn't comply, the block backend
remains unused. This triggers a warning since commit a66c9dc, v2.2.0.
Drives created by default are exempted; use -nodefaults to get rid of
them.
Turn this warning into an error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-8-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types implicitly default to if=ide that way, even though
they don't actually have an IDE controller. This makes no sense.
Change the implicit default to if=none. Affected machines:
* all targets: none
* aarch64/arm: akita ast2500 canon cheetah collie connex imx25
integratorcp kzm lm3s6965evb lm3s811evb mainstone musicpal n800 n810
netduino2 nuri palmetto realview romulus sabrelite smdkc210 sx1 sx1
verdex z2
* cris: axis-dev88
* i386/x86_64: xenpv
* lm32: lm32-evr lm32-uclinux milkymist
* m68k: an5206 dummy mcf5208evb
* microblaze/microblazeel: petalogix-ml605 petalogix-s3adsp1800
* mips/mips64/mips64el/mipsel: mipssim
* moxie: moxiesim
* or32: or32-sim
* ppc/ppc64/ppcemb: bamboo ref405ep taihu virtex-ml507
* ppc/ppc64: mpc8544ds ppce500
* sh4/sh4eb: shix
* sparc: leon3_generic
* sparc64: niagara
* tricore: tricore_testboard
* unicore32: puv3
* xtensa/xtensaeb: kc705 lx200 lx60 ml605 sim
None of these machines have an IDE controller, let alone code to
honor if=ide.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: Michael Walle <michael@walle.cc>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: Anthony Green <green@moxielogic.com>
Cc: Jia Liu <proljc@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-ppc@nongnu.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Fabien Chouteau <chouteau@adacore.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-By: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-4-git-send-email-armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-19-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
it's not very convenient to use the crash-information property interface,
so provide a CPU class callback to get the guest crash information, and pass
that information in the event
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1487053524-18674-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch:
* moves vm_start to cpus.c.
* exports qemu_vmstop_requested, since it's needed by vm_start.
* extracts vm_prepare_start from vm_start; it does what vm_start did,
except restarting the cpus.
* vm_start now calls vm_prepare_start and then restarts the cpus.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1487092068-16562-2-git-send-email-imbrenda@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Those could probably be squashed with earlier patches, however I
couldn't easily identify them, test them or check if there are still
necessary on various platforms.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This define is used by several character devices, place it in char
common header.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
A mechanical move, except that qemu_chr_write_all() needs to be declared
in char.h header to be used from chardev unit files.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The class kind is necessary to lookup the chardev name in
qmp_chardev_add() after calling qemu_chr_new_from_opts() and to set
the appropriate ChardevBackend (mainly to free the right
fields).
qemu_chr_new_from_opts() can be changed to use a non-qmp function
using the chardev class typename. Introduce qemu_chardev_add() to be
called from qemu_chr_new_from_opts() and remove the class chardev kind
field. Set the backend->type in the parse callback (when non-common
fields are added).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
CharDriver no longer exists, it has been replaced with Chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
qemu_chr_new_from_opts() is modified to not need CharDriver backend[]
array, but uses instead objectified qmp_query_chardev_backends() and
char_get_class(). The alias field is moved outside in a ChardevAlias[],
similar to QDevAlias for devices.
"kind" and "parse" are moved to ChardevClass ("kind" is to be removed
next)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Now it uses Object instance_finalize instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Turn Chardev into Object.
qemu_chr_alloc() is replaced by the qemu_chardev_new() constructor. It
will call qemu_char_open() to open/intialize the chardev with the
ChardevCommon *backend settings.
The CharDriver::create() callback is turned into a ChardevClass::open()
which is called from the newly introduced qemu_chardev_open().
"chardev-gdb" and "chardev-hci" are internal chardev and aren't
creatable directly with -chardev. Use a new internal flag to disable
them. We may want to use TYPE_USER_CREATABLE interface instead, or
perhaps allow -chardev usage.
Although in general we keep typename and macros private, unless the type
is being used by some other file, in this patch, all types and common
helper macros for qemu-char.c are in char.h. This is to help transition
now (some types must be declared early, while some aren't shared) and
when splitting in several units. This is to be improved later.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of registering a vc handler to allocate the Gtk VC Chardev,
overwrite the console.c char driver.
A later patch, when switching to QOM, will register a default console vc
QOM class if none has been registered before.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a single allocation for CharDriverState, this avoids extra
allocations & pointers, and is a step towards more object-oriented
CharDriver.
Gtk console is a bit peculiar, gd_vc_chr_set_echo() used to have a
temporary VirtualConsole to save the echo bit. Instead now, we consider
whether vcd->console is set or not, and restore the echo bit saved in
VCDriverState when calling gd_vc_vte_init().
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a feature flag rather than a structure field for "replay".
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the "is_mux" field from CharDriverState.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the code more declarative, and avoids duplicating the
information on all instances.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to allocate & copy fields, let's use static const struct instead.
Add an alias field to the CharDriver structure to cover the cases where
we previously registered a driver twice under two names.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements initial vmstate creation or loading at the start
of record/replay. It is needed for rewinding the execution in the replay mode.
v4 changes:
- snapshots are not created by default anymore
v3 changes:
- added rrsnapshot option
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071746.4572.61449.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces save_vmstate function to allow saving and loading
vmstates from the replay module.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071741.4572.13714.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add remaining bits of the Altera NiosII R1 support into qemu, which
is documentation, MAINTAINERS file entry, configure bits, arch_init
and configuration files for both linux-user (userland binaries) and
softmmu (hardware emulation).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-8-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use the Intel HAX is kernel-based hardware acceleration module for
Windows (similar to KVM on Linux).
Based on the "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <7b9cae28a0c379ab459c7a8545c9a39762bd394f.1484045952.git.vpalatin@chromium.org>
[Drop hax_populate_ram stub. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
That's a forward port of the core HAX interface code from the
emu-2.2-release branch in the external/qemu-android repository as used by
the Android emulator.
The original commit was "target/i386: Add Intel HAX to android emulator"
saying:
"""
Backport of 2b3098ff27bab079caab9b46b58546b5036f5c0c
from studio-1.4-dev into emu-master-dev
Intel HAX (harware acceleration) will enhance android emulator performance
in Windows and Mac OS X in the systems powered by Intel processors with
"Intel Hardware Accelerated Execution Manager" package installed when
user runs android emulator with Intel target.
Signed-off-by: David Chou <david.j.chou@intel.com>
"""
It has been modified to build and run along with the current code base.
The formatting has been fixed to go through scripts/checkpatch.pl,
and the DPRINTF macros have been updated to get the instanciations checked by
the compiler.
The FPU registers saving/restoring has been updated to match the current
QEMU registers layout.
The implementation has been simplified by doing the following modifications:
- removing the code for supporting the hardware without Unrestricted Guest (UG)
mode (including all the code to fallback on TCG emulation).
- not including the Darwin support (which is not yet debugged/tested).
- simplifying the initialization by removing the leftovers from the Android
specific code, then trimming down the remaining logic.
- removing the unused MemoryListener callbacks.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <e1023837f8d0e4c470f6c4a3bf643971b2bca5be.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Copy the mechanism of hw/smbios/smbios-stub.c to implement an ACPI-stub
instead, so that -acpitable can be later extended to ARM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They are small, it is not worth stubbing them. Just include them
in user-mode emulators and unit tests as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-smbios command line options were accepted but silently ignored on
TARGET_ARM, due to a test for TARGET_I386 in arch_init.c.
Copy the mechanism of hw/pci/pci-stub.c to implement an smbios-stub
instead, enabled for all targets without CONFIG_SMBIOS.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Message-Id: <20161222151828.28292-1-leif.lindholm@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
so it won't impose an additional limits on max_cpus limits
supported by different targets.
It removes global MAX_CPUMASK_BITS constant and need to
bump it up whenever max_cpus is being increased for
a target above MAX_CPUMASK_BITS value.
Use runtime max_cpus value instead to allocate sufficiently
sized node_cpu bitmasks in numa parser.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1479466974-249781-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added asserts to ensure cpu_index < max_cpus]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Considering 'id' is mandatory for user_creatable objects/backends
and user_creatable_add_type() always has it as an argument
regardless of where from it is called CLI/monitor or QMP,
Fix issue by adding 'id' property to hostmem backends and
set it in user_creatable_add_type() for every object that
implements 'id' property. Then later at query-memdev time
get 'id' from object directly.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1484052795-158195-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The ready flag should be set by the children of
cryptodev backend interface. Warp the setter/getter
functions for it.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This property is used to Tag the cryptodev backend
is used by virtio-crypto or not. Making cryptodev
can't be hot unplugged when it's in use. Cleanup
resources when cryptodev is finalized.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds support of recording and replaying network packets in
irount rr mode.
Record and replay for network interactions is performed with the network filter.
Each backend must have its own instance of the replay filter as follows:
-netdev user,id=net1 -device rtl8139,netdev=net1
-object filter-replay,id=replay,netdev=net1
Replay network filter is used to record and replay network packets. While
recording the virtual machine this filter puts all packets coming from
the outer world into the log. In replay mode packets from the log are
injected into the network device. All interactions with network backend
in replay mode are disabled.
v5 changes:
- using iov_to_buf function instead of loop
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
These parameters control the poll time self-tuning algorithm. They are
optional and will default to sane values if omitted.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20161201192652.9509-14-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Poll mode can be configured with -object iothread,poll-max-ns=NUM.
Polling is disabled with a value of 0 nanoseconds.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20161201192652.9509-7-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We use an opaque point to the VirtIOCryptoReq which
can support different packets based on different
algorithms.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reuse the existing locking provided by stdio to keep in_asm, cpu,
op, op_opt, op_ind, and out_asm as contiguous blocks.
While it isn't possible to interleave e.g. in_asm or op_opt logs
because of the TB lock protecting all code generation, it is
possible to interleave cpu logs, or to interleave a cpu dump with
an out_asm dump.
For mingw32, we appear to have no viable solution for this. The locking
functions are not properly exported from the system runtime library.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This patch adds session operation and crypto operation
stuff in the cryptodev backend, including function
pointers and corresponding structures.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cryptodev backend interface is used to realize the active work for
virtual crypto device.
This patch only add the framework, doesn't include specific operations.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The hard-coded default alignment is BDRV_SECTOR_SIZE, however this is not
necessarily the case for all platforms. Use this as the default alignment for
all current callers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1476445266-27503-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
All read/write functions already have a single coroutine-based function
on the BlockBackend level through which all requests go (no matter what
API style the external caller used) and which passes the requests down
to the block node level.
This patch exports a bdrv_co_ioctl() function and uses it to extend this
mode of operation to ioctls.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
so that it would be possible to increase maxcpus limit
for x86 target. Keep spapr/virt_arm at limit they used
to have 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It's only used in qmp_chardev_add(), so use a create() argument instead.
Also switched to typedef functions for CharDriverParse/CharDriverCreate.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to count the users of a CharDriverState, it can rely on the fact
of whether there is a CharBackend associated or if there is enough space
in the muxer.
Simplify and fold chr_mux_new_fe() in qemu_chr_fe_init() since there is
a single user now. Also switch from fprintf to raising error instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I introduced this function in d61b0c9a2f, but it isn't
used. Furthermore, it was incomplete, as it would need to translate QEMU
chr events to Spice port events.
(presumably it was used in the follow-up NBD-spice series that was not
completed: http://lists.gnu.org/archive/html/qemu-devel/2013-11/msg02024.html)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-4-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This may help to catch unhandled cases, and avoid having to maintain
numbering.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-3-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Usage has long been removed, since commit f220174de8.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-2-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The fe_open state belongs to front end.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function is used to free the backend opaque pointer, let's name it
accordingly.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-23-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the hanlders are associated with a CharBackend, rather than the
CharDriverState, it is more appropriate to store in CharBackend. This
avoids the handler copy dance in qemu_chr_fe_set_handlers() then
mux_chr_update_read_handler(), by storing the CharBackend pointer
directly.
Also a mux CharDriver should go through mux->backends[focused], since
chr->be will stay NULL. Before that, it was possible to call
chr->handler by mistake with surprising results, for ex through
qemu_chr_be_can_write(), which would result in calling the last set
handler front end, not the one with focus.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-22-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all front end use qemu_chr_fe_init(), we can move chardev
claiming in init(), and add a function deinit() to release the chardev
and cleanup handlers.
The qemu_chr_fe_claim_no_fail() for property are gone, since the
property will raise an error instead. In other cases, where there is
already an error path, an error is raised instead. Finally, other cases
are handled by &error_abort in qemu_chr_fe_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-19-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_add_handlers*() have been removed in previous change, so the
common qemu_chr_set_handlers() is no longer needed.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-17-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This new structure is meant to keep the details associated with a char
driver usage. On initialization, it gets a tag from the mux backend.
It can change its handlers thanks to qemu_chr_fe_set_handlers().
This structure is introduced so that all frontend will be moved to hold
and use a CharBackend. This will allow to better track char usage and
allocation, and help prevent some memory leaks or corruption.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-10-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make qemu_chr_add_handlers_full() aware of mux handling. This allows
introduction of a tag associated with the fe handlers and a
qemu_chr_set_handlers() function to set the handler for a particular
tag. That will allow to get rid of qemu_chr_add_handlers*() in later
changes, in favor of qemu_chr_fe_set_handler().
To this end, chr_update_read_handler callback is enhanced with a tag
argument, and mux_chr_update_read_handler() is splitted in new
functions: mux_chr_new_handler_tag(), mux_chr_set_handlers(),
mux_set_focus().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-9-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CharDriverState.init() callback is no longer set since commit
a61ae7f88c and thus unused. The only user, the malta FGPA display has
been converted to use an event "opened" callback instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
That commit mis-used mux char: the frontend are multiplexed, not the
backend. Fix the regression preventing "c-a c" to switch the focus. The
following patches will fix the crash (when leaving or removing frontend)
by tracking frontends with handler tags.
This reverts commit 949055a254.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The vhost-user & colo code is poking at the QemuOpts instance
in the CharDriverState struct, not realizing that it is valid
for this to be NULL. e.g. the following crash shows a codepath
where it will be NULL:
Program terminated with signal SIGSEGV, Segmentation fault.
#0 0x000055baf6ab4adc in qemu_opt_foreach (opts=0x0, func=0x55baf696b650 <net_vhost_chardev_opts>, opaque=0x7ffc51368c00, errp=0x7ffc51368e48) at util/qemu-option.c:617
617 QTAILQ_FOREACH(opt, &opts->head, next) {
[Current thread is 1 (Thread 0x7f1d4970bb40 (LWP 6603))]
(gdb) bt
#0 0x000055baf6ab4adc in qemu_opt_foreach (opts=0x0, func=0x55baf696b650 <net_vhost_chardev_opts>, opaque=0x7ffc51368c00, errp=0x7ffc51368e48) at util/qemu-option.c:617
#1 0x000055baf696b7da in net_vhost_parse_chardev (opts=0x55baf8ff9260, errp=0x7ffc51368e48) at net/vhost-user.c:314
#2 0x000055baf696b985 in net_init_vhost_user (netdev=0x55baf8ff9250, name=0x55baf879d270 "hostnet2", peer=0x0, errp=0x7ffc51368e48) at net/vhost-user.c:360
#3 0x000055baf6960216 in net_client_init1 (object=0x55baf8ff9250, is_netdev=true, errp=0x7ffc51368e48) at net/net.c:1051
#4 0x000055baf6960518 in net_client_init (opts=0x55baf776e7e0, is_netdev=true, errp=0x7ffc51368f00) at net/net.c:1108
#5 0x000055baf696083f in netdev_add (opts=0x55baf776e7e0, errp=0x7ffc51368f00) at net/net.c:1186
#6 0x000055baf69608c7 in qmp_netdev_add (qdict=0x55baf7afaf60, ret=0x7ffc51368f50, errp=0x7ffc51368f48) at net/net.c:1205
#7 0x000055baf6622135 in handle_qmp_command (parser=0x55baf77fb590, tokens=0x7f1d24011960) at /path/to/qemu.git/monitor.c:3978
#8 0x000055baf6a9d099 in json_message_process_token (lexer=0x55baf77fb598, input=0x55baf75acd20, type=JSON_RCURLY, x=113, y=19) at qobject/json-streamer.c:105
#9 0x000055baf6abf7aa in json_lexer_feed_char (lexer=0x55baf77fb598, ch=125 '}', flush=false) at qobject/json-lexer.c:319
#10 0x000055baf6abf8f2 in json_lexer_feed (lexer=0x55baf77fb598, buffer=0x7ffc51369170 "}R\204\367\272U", size=1) at qobject/json-lexer.c:369
#11 0x000055baf6a9d13c in json_message_parser_feed (parser=0x55baf77fb590, buffer=0x7ffc51369170 "}R\204\367\272U", size=1) at qobject/json-streamer.c:124
#12 0x000055baf66221f7 in monitor_qmp_read (opaque=0x55baf77fb530, buf=0x7ffc51369170 "}R\204\367\272U", size=1) at /path/to/qemu.git/monitor.c:3994
#13 0x000055baf6757014 in qemu_chr_be_write_impl (s=0x55baf7610a40, buf=0x7ffc51369170 "}R\204\367\272U", len=1) at qemu-char.c:387
#14 0x000055baf6757076 in qemu_chr_be_write (s=0x55baf7610a40, buf=0x7ffc51369170 "}R\204\367\272U", len=1) at qemu-char.c:399
#15 0x000055baf675b3b0 in tcp_chr_read (chan=0x55baf90244b0, cond=G_IO_IN, opaque=0x55baf7610a40) at qemu-char.c:2927
#16 0x000055baf6a5d655 in qio_channel_fd_source_dispatch (source=0x55baf7610df0, callback=0x55baf675b25a <tcp_chr_read>, user_data=0x55baf7610a40) at io/channel-watch.c:84
#17 0x00007f1d3e80cbbd in g_main_context_dispatch () from /usr/lib64/libglib-2.0.so.0
#18 0x000055baf69d3720 in glib_pollfds_poll () at main-loop.c:213
#19 0x000055baf69d37fd in os_host_main_loop_wait (timeout=126000000) at main-loop.c:258
#20 0x000055baf69d38ad in main_loop_wait (nonblocking=0) at main-loop.c:506
#21 0x000055baf676587b in main_loop () at vl.c:1908
#22 0x000055baf676d3bf in main (argc=101, argv=0x7ffc5136a6c8, envp=0x7ffc5136a9f8) at vl.c:4604
(gdb) p opts
$1 = (QemuOpts *) 0x0
The crash occurred when attaching vhost-user net via QMP:
{
"execute": "chardev-add",
"arguments": {
"id": "charnet2",
"backend": {
"type": "socket",
"data": {
"addr": {
"type": "unix",
"data": {
"path": "/var/run/openvswitch/vhost-user1"
}
},
"wait": false,
"server": false
}
}
},
"id": "libvirt-19"
}
{
"return": {
},
"id": "libvirt-19"
}
{
"execute": "netdev_add",
"arguments": {
"type": "vhost-user",
"chardev": "charnet2",
"id": "hostnet2"
},
"id": "libvirt-20"
}
Code using chardevs should not be poking at the internals of the
CharDriverState struct. What vhost-user wants is a chardev that is
operating as reconnectable network service, along with the ability
to do FD passing over the connection. The colo code simply wants
a network service. Add a feature concept to the char drivers so
that chardev users can query the actual features they wish to have
supported. The QemuOpts member is removed to prevent future mistakes
in this area.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replace repeated pattern
for (i = 0; i < nb_numa_nodes; i++) {
if (test_bit(idx, numa_info[i].node_cpu)) {
...
break;
with a helper function to lookup numa node index for cpu.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Almost all block devices are qdevified by now. This allows us to go back
from the BlockBackend to the DeviceState. xen_disk is the last device
that is missing. We'll remember in the BlockBackend if a xen_disk is
attached and can then disable any features that require going from a BB
to the DeviceState.
While at it, clearly mark the function used by xen_disk as legacy even
in its name, not just in TODO comments.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Recently we moved a few options from QemuOptsLists in blockdev.c to
bdrv_runtime_opts in block.c in order to make them accissble using
blockdev-add. However, this has the side effect that these options are
missing from query-command-line-options now, and libvirt consequently
disables the corresponding feature.
This problem was reported as a regression for the 'discard' option,
introduced in commit 818584a4. However, it is more general than that.
Fix it by adding bdrv_runtime_opts to the list of QemuOptsLists that are
returned in query-command-line-options. For the future, libvirt is
advised to use QMP schema introspection for block device options.
Reported-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Michal Privoznik <mprivozn@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Introduce global kvm_msi_use_devid flag plus associated
kvm_msi_devid_required() macro. Passes the device ID,
if needed, while building the MSI route entry. Device IDs are
required by the ARM GICv3 ITS (IRQ remapping function is based on
this information).
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-5-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
mux_chr_update_read_handler() is adding a new mux_cnt each time
mux_chr_update_read_handler() is called, it's not possible to actually
update the "child" chr callbacks that were set previously. This may lead
to crashes if the "child" chr is destroyed:
valgrind x86_64-softmmu/qemu-system-x86_64 -chardev
stdio,mux=on,id=char0 -mon chardev=char0,mode=control,default
when quitting:
==4306== Invalid read of size 8
==4306== at 0x8061D3: json_lexer_destroy (json-lexer.c:385)
==4306== by 0x7E39F8: json_message_parser_destroy (json-streamer.c:134)
==4306== by 0x3447F6: monitor_qmp_event (monitor.c:3908)
==4306== by 0x480153: mux_chr_send_event (qemu-char.c:630)
==4306== by 0x480694: mux_chr_event (qemu-char.c:734)
==4306== by 0x47F1E9: qemu_chr_be_event (qemu-char.c:205)
==4306== by 0x481207: fd_chr_close (qemu-char.c:1114)
==4306== by 0x481659: qemu_chr_close_stdio (qemu-char.c:1221)
==4306== by 0x486F07: qemu_chr_free (qemu-char.c:4146)
==4306== by 0x486F97: qemu_chr_delete (qemu-char.c:4154)
==4306== by 0x487E66: qemu_chr_cleanup (qemu-char.c:4678)
==4306== by 0x495A98: main (vl.c:4675)
==4306== Address 0x28439e90 is 112 bytes inside a block of size 240 free'd
==4306== at 0x4C2CD5A: free (vg_replace_malloc.c:530)
==4306== by 0x1E4CBF2D: g_free (in /usr/lib64/libglib-2.0.so.0.4800.2)
==4306== by 0x344DE9: monitor_cleanup (monitor.c:4058)
==4306== by 0x495A93: main (vl.c:4674)
==4306== Block was alloc'd at
==4306== at 0x4C2BBAD: malloc (vg_replace_malloc.c:299)
==4306== by 0x1E4CBE18: g_malloc (in /usr/lib64/libglib-2.0.so.0.4800.2)
==4306== by 0x344BF8: monitor_init (monitor.c:4021)
==4306== by 0x49063C: mon_init_func (vl.c:2417)
==4306== by 0x7FC6DE: qemu_opts_foreach (qemu-option.c:1116)
==4306== by 0x4954E0: main (vl.c:4473)
Instead, keep the "child" chr associated with a particular idx so its
handlers can be updated and removed to avoid the crash.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161003094704.18087-3-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
the allocated stack will be adjusted to the minimum supported stack size
by the OS and rounded up to be a multiple of the system pagesize.
Additionally an architecture dependent guard page is added to the stack
to catch stack overflows.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of modifying the new BDS after it has been opened, use the newly
supported 'detect-zeroes' option in bdrv_open_common() so that all
requirements are checked (detect-zeroes=unmap requires discard=unmap).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We can teach Xen to drain and flush each device as it needs to, instead
of trying to flush ALL devices. This removes the last user of
blk_flush_all.
The function is therefore removed under the premise that any new uses
of blk_flush_all would be the wrong paradigm: either flush the single
device that requires flushing, or use an appropriate flush_all mechanism
from outside of the BlkBackend layer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
