Remove the is_sse200 flag in favour of just directly testing the new
sse_version field.
Since some of these registers exist in the SSE-300 but some do not or
have different behaviour, we expand out the if() statements in the
read and write functions into switch()es, so we have an easy place to
put SSE-300 specific behaviour.
(Until we do add the SSE-300 behaviour, the thing preventing us
reaching the "unreachable" default cases is that armsse.c doesn't
yet pass us an ARMSSE_SSE300 version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-7-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
Add PCI interface support for PVPANIC device. Create a new file pvpanic-pci.c
where the PCI specific routines reside and update the build system with the new
files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This both allows the wiring to be done as Ben suggested in his original comment in
gpio.c and also enables the OpenPIC object property link to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The OpenPIC device is located within the macio device on real hardware so make it
a child of the macio-newworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-newworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The heathrow PIC is located within the macio device on real hardware so make it
a child of the macio-oldworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-oldworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch makes NPCM7XX Timer to use a the timer clock generated by the
CLK module instead of the magic number TIMER_REF_HZ.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows NPCM7XX CLK module to compute clocks that are used by
other NPCM7XX modules.
Add a new struct NPCM7xxClockConverterState which represents a
single converter. Each clock converter in CLK module represents one
converter in NPCM7XX CLK Module(PLL, SEL or Divider). Each converter
takes one or more input clocks and converts them into one output clock.
They form a clock hierarchy in the CLK module and are responsible for
outputing clocks for various other modules in an NPCM7XX SoC.
Each converter has a function pointer called "convert" which represents
the unique logic for that converter.
The clock contains two initialization information: ConverterInitInfo and
ConverterConnectionInfo. They represent the vertices and edges in the
clock diagram respectively.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201016143509.26692-1-chetan4windows@gmail.com>
[PMD: Split hw/ vs target/]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This creates a minimum model for Microchip PolarFire SoC SYSREG
module. It only implements the ENVM_CR register to tell guest
software that eNVM is running at the configured divider rate.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-7-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This creates a model for PolarFire SoC IOSCB [1] module. It actually
contains lots of sub-modules like various PLLs to control different
peripherals. Only the mininum capabilities are emulated to make the
HSS DDR memory initialization codes happy. Lots of sub-modules are
created as an unimplemented devices.
[1] PF_SoC_RegMap_V1_1/MPFS250T/mpfs250t_ioscb_memmap_dri.htm in
https://www.microsemi.com/document-portal/doc_download/1244581-polarfire-soc-register-map
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-5-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The PolarFire SoC DDR Memory Controller mainly includes 2 modules,
called SGMII PHY module and the CFG module, as documented in the
chipset datasheet.
This creates a single file that groups these 2 modules, providing
the minimum functionalities that make the HSS DDR initialization
codes happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-3-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
-----BEGIN PGP SIGNATURE-----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=inaF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/led-api-20201026' into staging
API to model LED.
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
# gpg: Signature made Mon 26 Oct 2020 22:03:59 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/led-api-20201026:
hw/arm/tosa: Replace fprintf() calls by LED devices
hw/misc/mps2-scc: Use the LED device
hw/misc/mps2-fpgaio: Use the LED device
hw/arm/aspeed: Add the 3 front LEDs drived by the PCA9552 #1
hw/misc/led: Emit a trace event when LED intensity has changed
hw/misc/led: Allow connecting from GPIO output
hw/misc/led: Add a LED device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Those reset values have been extracted from a Raspberry Pi 3 model B
v1.2, using the 2020-08-20 version of raspios. The dump was done using
the debugfs interface of the CPRMAN driver in Linux (under
'/sys/kernel/debug/clk'). Each exposed clock tree stage (PLLs, channels
and muxes) can be observed by reading the 'regdump' file (e.g.
'plla/regdump').
Those values are set by the Raspberry Pi firmware at boot time (Linux
expects them to be set when it boots up).
Some stages are not exposed by the Linux driver (e.g. the PLL B). For
those, the reset values are unknown and left to 0 which implies a
disabled output.
Once booted in QEMU, the final clock tree is very similar to the one
visible on real hardware. The differences come from some unimplemented
devices for which the driver simply disable the corresponding clock.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This simple mux sits between the PLL channels and the DSI0E and DSI0P
clock muxes. This mux selects between PLLA-DSI0 and PLLD-DSI0 channel
and outputs the selected signal to source number 4 of DSI0E/P clock
muxes. It is controlled by the cm_dsi0hsck register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The clock multiplexers are the last clock stage in the CPRMAN. Each mux
outputs one clock signal that goes out of the CPRMAN to the SoC
peripherals.
Each mux has at most 10 sources. The sources 0 to 3 are common to all
muxes. They are:
0. ground (no clock signal)
1. the main oscillator (xosc)
2. "test debug 0" clock
3. "test debug 1" clock
Test debug 0 and 1 are actual clock muxes that can be used as sources to
other muxes (for debug purpose).
Sources 4 to 9 are mux specific and can be unpopulated (grounded). Those
sources are fed by the PLL channels outputs.
One corner case exists for DSI0E and DSI0P muxes. They have their source
number 4 connected to an intermediate multiplexer that can select
between PLLA-DSI0 and PLLD-DSI0 channel. This multiplexer is called
DSI0HSCK and is not a clock mux as such. It is really a simple mux from
the hardware point of view (see https://elinux.org/The_Undocumented_Pi).
This mux is not implemented in this commit.
Note that there is some muxes for which sources are unknown (because of
a lack of documentation). For those cases all the sources are connected
to ground in this implementation.
Each clock mux output is exported by the CPRMAN at the qdev level,
adding the suffix '-out' to the mux name to form the output clock name.
(E.g. the 'uart' mux sees its output exported as 'uart-out' at the
CPRMAN level.)
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PLLs are composed of multiple channels. Each channel outputs one clock
signal. They are modeled as one device taking the PLL generated clock as
input, and outputting a new clock.
A channel shares the CM register with its parent PLL, and has its own
A2W_CTRL register. A write to the CM register will trigger an update of
the PLL and all its channels, while a write to an A2W_CTRL channel
register will update the required channel only.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN PLLs generate a clock based on a prescaler, a multiplier and
a divider. The prescaler doubles the parent (xosc) frequency, then the
multiplier/divider are applied. The multiplier has an integer and a
fractional part.
This commit also implements the CPRMAN CM_LOCK register. This register
reports which PLL is currently locked. We consider a PLL has being
locked as soon as it is enabled (on real hardware, there is a delay
after turning a PLL on, for it to stabilize).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 5 PLLs in the CPRMAN, namely PLL A, C, D, H and B. All of them
take the xosc clock as input and produce a new clock.
This commit adds a skeleton implementation for the PLLs as sub-devices
of the CPRMAN. The PLLs are instantiated and connected internally to the
main oscillator.
Each PLL has 6 registers : CM, A2W_CTRL, A2W_ANA[0,1,2,3], A2W_FRAC. A
write to any of them triggers a call to the (not yet implemented)
pll_update function.
If the main oscillator changes frequency, an update is also triggered.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 8 LEDs connected to the MCC.
This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 2 LEDs connected to the FPGA.
This replaces the 'mps2_fpgaio_leds' trace events by the generic
'led_set_intensity' event.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
Some devices expose GPIO lines.
Add a GPIO qdev input to our LED device, so we can
connect a GPIO output using qdev_connect_gpio_out().
When used with GPIOs, the intensity can only be either
minium or maximum. This depends of the polarity of the
GPIO (which can be inverted).
Declare the GpioPolarity type to model the polarity.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-3-f4bug@amsat.org>
Add a LED device which can be connected to a GPIO output.
They can also be dimmed with PWM devices. For now we do
not implement the dimmed mode, but in preparation of a
future implementation, we start using the LED intensity.
LEDs are limited to a fixed set of colors.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
Add '-drive' support to OTP device. Allow users to assign a raw file
as OTP image.
test commands for 16k otp.img filled with zero:
$ dd if=/dev/zero of=./otp.img bs=1k count=16
$ ./qemu-system-riscv64 -M sifive_u -m 256M -nographic -bios none \
-kernel ../opensbi/build/platform/sifive/fu540/firmware/fw_payload.elf \
-d guest_errors -drive if=none,format=raw,file=otp.img
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201020033732.12921-3-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- Add write operation to update fuse data bit when PWE bit is on.
- Add array, fuse_wo, to store the 'written' status for all bits
of OTP to block the write operation.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20201020033732.12921-2-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some objects accidentally inherit ObjectClass instead of Object.
They compile silently but may crash after downcasting.
In this patch, we introduce a coccinelle script to find broken
declarations and fix them manually with proper base type.
Signed-off-by: Sergey Nizovtsev <snizovtsev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Enough functionality to boot the Linux kernel has been implemented. This
includes:
- Correct power-on reset values so the various clock rates can be
accurately calculated.
- Clock enables stick around when written.
In addition, a best effort attempt to implement SECCNT and CNTR25M was
made even though I don't think the kernel needs them.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-3-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
