Slot present bit is cleared apparently for each device. Hotplug and non
hotplug devices should not mix normally, and we only set the bit when we
add a device so it should all work out, but it's more robust to
explicitly account for more than one device per slot.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCI hotplug eject register has always returned 0, so let's redefine
it as a hotplug feature register. The existing model of using separate
up & down read-only registers and an eject via write to this register
becomes the base implementation. As we make use of new interfaces we'll
set bits here to allow the BIOS and AML implementation to optimize for
the platform implementation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Clarify this register as read-only and remove write code. No
change in existing behavior.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As Michael Tsirkin demonstrated, current PCI hotplug is vulnerable
to a few races. The first is a race with other hotplug operations
because we clear the up & down registers at each event. If a new
event comes before the last is processed, up/down is cleared and
the event is lost.
To fix this for the down register, we create a life cycle for
the event request that starts with the hot unplug request in
piix4_device_hotplug() and ends when the device is ejected.
This allows us to mask and clear individual bits, preserving them
against races. For the up register, we have no clear end point
for when the event is finished. We could modify the BIOS to
acknowledge the bit and clear it, but this creates BIOS compatibiliy
issues without offering a complete solution. Instead we note that
gratuitous ACPI device checks are not harmful, which allows us to
issue a device check for every slot. We know which slots are present
and we know which slots are hotpluggable, so we can easily reduce
this to a more manageable set for the guest.
The other race Michael noted was that an unplug request followed
by reset may also lose the eject notification, which may also
result in the eject request being lost which a subsequent add
or remove. Once we're in reset, the device is unused and we can
flush the queue of device removals ourselves. Previously if a
device_del was issued to a guest without ACPI PCI hotplug support,
it was necessary to shutdown the guest to recover the device.
With this, a guest reboot is sufficient.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The write side of these registers is never used and actually can't be
used as defined because any read/modify/write sequence from the guest
potentially races with qemu. Drop the write support and define these
as read-only registers.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch switches pc s3 suspend over to the new infrastructure.
The cmos_s3 qemu_irq is killed, the new notifier is used instead.
The xen hack goes away with that too, the hypercall can simply be
done in a notifier function now.
This patch also makes the guest actually stay suspended instead
of leaving suspend instantly, so it is useful for more than just
testing whenever the suspend/resume cycle actually works.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Do APCIREGS->pm1.evt.en updates using the new acpi_pm1_evt_write_en
function, so the acpi code will see those updates.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Pretty pointless, can easily be reached via ACPIREGS now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All those acpi structs are not independent from each other.
Various acpi functions expecting multiple acpi structs passed
in are a clean indicator for that ;)
So this patch bundles all acpi structs in the new ACPIREGS
struct, then use it everythere pass around acpi state.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This was done in a mostly automated fashion. I did it in three steps and then
rebased it into a single step which avoids repeatedly touching every file in
the tree.
The first step was a sed-based addition of the parent type to the subclass
registration functions.
The second step was another sed-based removal of subclass registration functions
while also adding virtual functions from the base class into a class_init
function as appropriate.
Finally, a python script was used to convert the DeviceInfo structures and
qdev_register_subclass functions to TypeInfo structures, class_init functions,
and type_register_static calls.
We are almost fully converted to QOM after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now, DeviceInfo acts as the class for qdev. In order to switch to a
proper ObjectClass derivative, we need to ween all of the callers off of
interacting directly with the info pointer.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All files under GPLv2 will get GPLv2+ changes starting tomorrow.
event_notifier.c and exec-obsolete.h were only ever touched by Red Hat
employees and can be relicensed now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
SCSI buses will need to read the children list first-to-last. This
requires using a QTAILQ, because hell breaks loose if you just try
inserting at the tail (thus reversing the order of all existing
visits from last-to-first to first-to-tail).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows to pass additional information to the notifier callback
which is useful if sender and receiver do not share any other distinct
data structure.
Will be used first for the clock reset notifier.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Serial and parallel devices created with -device are not reported in
the PIIX4 configuration space, and are hence not picked up by the DSDT.
This upsets Windows, which hides them altogether from the guest.
To avoid this, check at the end of machine initialization whether the
corresponding I/O ports have been registered. The new function in
ioport.c does this; this also requires a tweak to isa_unassign_ioport.
I left the comment in piix4_pm_initfn since the registers I moved do
seem to match the 82371AB datasheet. There are some quirks though.
We are setting this bit:
"Device 8 EIO Enable (EIO_EN_DEV8)—R/W. 1=Enable PCI access to the
device 8 enabled I/O ranges to be claimed by PIIX4 and forwarded
to the ISA/EIO bus. 0=Disable. The LPT_MON_EN must be set to enable
the decode."
but not LPT_MON_EN (bit 18 at 50h):
LPT Port Enable (LPT_MON_EN)—R/W. 1=Enable accesses to parallel
port address range (LPT_DEC_SEL) to generate a device 8 (parallel
port) decode event. 0=Disable.
We're also setting the LPT_DEC_SEL field (that's the 0x60 written to
63h) to 11, which means reserved, rather than to 01 (378h-37Fh).
Likewise we're not setting SA_MON_EN, SB_MON_EN (respectively bit 14
and bit 16 at address 50h) for the serial ports. However, we're setting
COMA_DEC_SEL and COMB_DEC_SEL correctly, unlike the corresponding register
for the parallel port.
All these fields are left as they are, since they are probably only
meant to be used in the DSDT.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch makes qemu ignore unplug requests from the guest for pci
devices which are tagged as non-hotpluggable. Trouble spot is the
piix4 chipset with the ISA bridge. Requests to unplug that one will
make it go away together with all ISA bus devices, which are not
prepared to be unplugged and thus don't cleanup, leaving active
qemu timers behind in free'ed memory.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
factor out ACPI GPE logic. Later it will be used by ICH9 ACPI.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out ACPI PM1_CNT logic. This will be used by ich9 acpi.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out ACPI PM1a EVT logic.
Later this will be used by ich9 acpi.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out PM_TMR logic. Later This will be used by ich9 acpi.
Also fixes the same bug in vt82c686.c that was fixed by the following
commits.
> commit 055479feab
> Author: aliguori <aliguori@c046a42c-6fe2-441c-8c8c-71466251a162>
> Date: Wed Jan 21 16:31:20 2009 +0000
>
> Always return latest pmsts instead of the old one (Xiantao Zhang)
>
> It may lead to the issue when booting windows guests with acpi=1
> if return the old pmsts.
>
> Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
I enable acpi_piix4 debug, and got the following build errors:
# make
CC libhw64/acpi_piix4.o
cc1: warnings being treated as errors
/home/wency/source/qemu/hw/acpi_piix4.c: In function ‘pm_ioport_write’:
/home/wency/source/qemu/hw/acpi_piix4.c:193: error: format ‘%04x’ expects type ‘unsigned int’, but argument 2 has type ‘uint64_t’
/home/wency/source/qemu/hw/acpi_piix4.c:193: error: format ‘%04x’ expects type ‘unsigned int’, but argument 3 has type ‘uint64_t’
/home/wency/source/qemu/hw/acpi_piix4.c: In function ‘pm_ioport_read’:
/home/wency/source/qemu/hw/acpi_piix4.c:219: error: format ‘%04x’ expects type ‘unsigned int’, but argument 2 has type ‘uint64_t’
make[1]: *** [acpi_piix4.o] Error 1
make: *** [subdir-libhw64] Error 2
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose no_hotplug attribute via I/O port, so ACPI BIOS can indicate
removability status to guest OS.
An updated seabios is required to make use of this feature (seabios.git
commit ID 3c241edf3d7ef29c21).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tested-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch tags all pci devices which belong to the piix3/4 chipsets as
not hotpluggable (Host bridge, ISA bridge, IDE controller, ACPI bridge).
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch fixes hot unplug of cold plugged devices
(those present at system start), which got broken by
5beb8ad503 .
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cam Macdonell <cam@cs.ualberta.ca>
Tested-by: Cam Macdonell <cam@cs.ualberta.ca>
Reported-by: Cam Macdonell <cam@cs.ualberta.ca>.
Extract range functions from pci.h. These will be used by later patches
by non-PCI devices. Adjust current users.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
call hotplug callback even when not hotplug case for later use.
And move hotplug check into hotplug callback.
PCIE slot needs this for card presence detection.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
PCI hotplug currently doesn't work after a migration because
we don't migrate the enable bits of the GPE state. Pull hotplug
structs into vmstate.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
remove global variables, gpe and pci0_status by moving them
into PIIX4PMState.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add argument, DeviceState*, to pci hot plug callback.
The argument will be used later to remove global variable.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split acpi.c into the common part and the piix4 specific part.
The common part will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
