Stream in stream_prepare calls bdrv_change_backing_file() to change
backing-file in the metadata of bs.
It may use either backing-file parameter given by user or just take
filename of base on job start.
Backing file format is determined by base on job finish.
There are some problems with this design, we solve only two by this
patch:
1. Consider scenario with backing-file unset. Current concept of stream
supports changing of the base during the job (we don't freeze link to
the base). So, we should not save base filename at job start,
- let's determine name of the base on job finish.
2. Using direct base to determine filename and format is not very good:
base node may be a filter, so its filename may be JSON, and format_name
is not good for storing into qcow2 metadata as backing file format.
- let's use unfiltered_base
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[vsementsov: change commit subject, change logic in stream_prepare]
Message-Id: <20201216061703.70908-10-vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
If the flag BDRV_REQ_PREFETCH was set, skip idling read/write
operations in COR-driver. It can be taken into account for the
COR-algorithms optimization. That check is being made during the
block stream job by the moment.
Add the BDRV_REQ_PREFETCH flag to the supported_read_flags of the
COR-filter.
block: Modify the comment for the flag BDRV_REQ_PREFETCH as we are
going to use it alone and pass it to the COR-filter driver for further
processing.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20201216061703.70908-9-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add the new member supported_read_flags to the BlockDriverState
structure. It will control the flags set for copy-on-read operations.
Make the block generic layer evaluate supported read flags before they
go to a block driver.
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[vsementsov: use assert instead of abort]
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20201216061703.70908-8-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The test case #310 is similar to #216 by Max Reitz. The difference is
that the test #310 involves a bottom node to the COR filter driver.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[vsementsov: detach backing to test reads from top, limit to qcow2]
Message-Id: <20201216061703.70908-7-vsementsov@virtuozzo.com>
[mreitz: Add "# group:" line]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add an option to limit copy-on-read operations to specified sub-chain
of backing-chain, to make copy-on-read filter useful for block-stream
job.
Suggested-by: Max Reitz <mreitz@redhat.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[vsementsov: change subject, modified to freeze the chain,
do some fixes]
Message-Id: <20201216061703.70908-6-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Provide the possibility to pass the 'filter-node-name' parameter to the
block-stream job as it is done for the commit block job.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[vsementsov: comment indentation, s/Since: 5.2/Since: 6.0/]
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20201216061703.70908-5-vsementsov@virtuozzo.com>
[mreitz: s/commit/stream/]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Provide API for the COR-filter removal. Also, drop the filter child
permissions for an inactive state when the filter node is being
removed.
To insert the filter, the block generic layer function
bdrv_insert_node() can be used.
The new function bdrv_cor_filter_drop() may be considered as an
intermediate solution before the QEMU permission update system has
overhauled. Then we are able to implement the API function
bdrv_remove_node() on the block generic layer.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20201216061703.70908-4-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Provide API for insertion a node to backing chain.
Suggested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20201216061703.70908-3-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add support for the recently introduced functions
bdrv_co_preadv_part()
and
bdrv_co_pwritev_part()
to the COR-filter driver.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20201216061703.70908-2-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Unfortunately commit "iotests: handle tmpfs" breaks running iotests
with -nbd -nocache, as _check_o_direct tries to create
$TEST_IMG.test_o_direct, but in case of nbd TEST_IMG is something like
nbd+unix:///... , and test fails with message
qemu-img: nbd+unix:///?socket[...]test_o_direct: Protocol driver
'nbd' does not support image creation, and opening the image
failed: Failed to connect to '/tmp/tmp.[...]/nbd/test_o_direct': No
such file or directory
Use TEST_DIR instead.
Fixes: cfdca2b9f9
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20201218182012.47607-1-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Linking of qemu-system-ppc64 fails on macOS with dtrace enabled:
error: probe tpm_spapr_show_buffer doesn't exist
error: Could not register probes
ld: error creating dtrace DOF section for architecture x86_64
The failure is explained in 8c8ed03850 ("net/colo: Match is-enabled
probe to tracepoint"). In short, is-enabled probe can't be used without
a matching trace probe. And for this particular case
tpm_util_show_buffer probe should be enabled to print TPM buffer.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgDonvAAoJEO8Ells5jWIR++8IAJBTpKDSwdwG1ySn5m6tHZHM
GdFD2Ao8R8VsonJzw9i/1Gfn9T0icndRU6VC+nJEdvSLXUDoAQdmMmLCk4oml41g
gzPzsc6bFKwKB4DG3RyixbEoUsMl7jQRoVYOgWy1Ezx2daAGG9PjuDMdBU4tNCFv
IxkVpOz3RClhzaMz3O0OkLKljooRcvhePB+8FuZCOnBzxDJ9RU1KXDpv5kYMswFL
9f+D2UK474IcaAQCzKXuHrs/k3utMEY32udjqQdgb9y/8jZYJuEZSB7pyXozuSAO
QSl62FxbAwfx85hVbMqnIa2Yd629SiVVHsotavAZz60fcBaQgrNbBTWDNlCrWJo=
=XN54
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 25 Jan 2021 09:05:51 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: checksum: Introduce fine control over checksum type
net: checksum: Add IP header checksum calculation
net: checksum: Skip fragmented IP packets
net: Fix handling of id in netdev_add and netdev_del
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Various improvements for SD cards in SPI mode (Bin Meng)
-----BEGIN PGP SIGNATURE-----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=B3sY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sdmmc-20210124' into staging
SD/MMC patches
- Various improvements for SD cards in SPI mode (Bin Meng)
# gpg: Signature made Sun 24 Jan 2021 19:16:55 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sdmmc-20210124:
hw/sd: sd.h: Cosmetic change of using spaces
hw/sd: ssi-sd: Use macros for the dummy value and tokens in the transfer
hw/sd: ssi-sd: Fix the wrong command index for STOP_TRANSMISSION
hw/sd: ssi-sd: Add a state representing Nac
hw/sd: ssi-sd: Suffix a data block with CRC16
util: Add CRC16 (CCITT) calculation routines
hw/sd: sd: Drop sd_crc16()
hw/sd: sd: Support CMD59 for SPI mode
hw/sd: ssi-sd: Fix incorrect card response sequence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present net_checksum_calculate() blindly calculates all types of
checksums (IP, TCP, UDP). Some NICs may have a per type setting in
their BDs to control what checksum should be offloaded. To support
such hardware behavior, introduce a 'csum_flag' parameter to the
net_checksum_calculate() API to allow fine control over what type
checksum is calculated.
Existing users of this API are updated accordingly.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
At present net_checksum_calculate() only calculates TCP/UDP checksum
in an IP packet, but assumes the IP header checksum to be provided
by the software, e.g.: Linux kernel always calculates the IP header
checksum. However this might not always be the case, e.g.: for an IP
checksum offload enabled stack like VxWorks, the IP header checksum
can be zero.
This adds the checksum calculation of the IP header.
Signed-off-by: Guishan Qin <guishan.qin@windriver.com>
Signed-off-by: Yabing Liu <yabing.liu@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
To calculate the TCP/UDP checksum we need the whole datagram. Unless
the hardware has some logic to collect all fragments before sending
the whole datagram first, it can only be done by the network stack,
which is normally the case for the NICs we have seen so far.
Skip these fragmented IP packets to avoid checksum corruption.
Signed-off-by: Markus Carlstedt <markus.carlstedt@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
CLI -netdev accumulates in option group "netdev".
Before commit 08712fcb85 "net: Track netdevs in NetClientState rather
than QemuOpt", netdev_add added to the option group, and netdev_del
removed from it, both HMP and QMP. Thus, every netdev had a
corresponding QemuOpts in this option group.
Commit 08712fcb85 dropped this for QMP netdev_add and both netdev_del.
Now a netdev has a corresponding QemuOpts only when it was created
with CLI or HMP. Two issues:
* QMP and HMP netdev_del can leave QemuOpts behind, breaking HMP
netdev_add. Reproducer:
$ qemu-system-x86_64 -S -display none -nodefaults -monitor stdio
QEMU 5.1.92 monitor - type 'help' for more information
(qemu) netdev_add user,id=net0
(qemu) info network
net0: index=0,type=user,net=10.0.2.0,restrict=off
(qemu) netdev_del net0
(qemu) info network
(qemu) netdev_add user,id=net0
upstream-qemu: Duplicate ID 'net0' for netdev
Try "help netdev_add" for more information
Fix by restoring the QemuOpts deletion in qmp_netdev_del(), but with
a guard, because the QemuOpts need not exist.
* QMP netdev_add loses its "no duplicate ID" check. Reproducer:
$ qemu-system-x86_64 -S -display none -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 92, "minor": 1, "major": 5}, "package": "v5.2.0-rc2-1-g02c1f0142c"}, "capabilities": ["oob"]}}
{"execute": "qmp_capabilities"}
{"return": {}}
{"execute": "netdev_add", "arguments": {"type": "user", "id":"net0"}}
{"return": {}}
{"execute": "netdev_add", "arguments": {"type": "user", "id":"net0"}}
{"return": {}}
Fix by adding a duplicate ID check to net_client_init1() to replace
the lost one. The check is redundant for callers where QemuOpts
still checks, i.e. for CLI and HMP.
Reported-by: Andrew Melnichenko <andrew@daynix.com>
Fixes: 08712fcb85
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix running during atomic single-step.
Partial support for apple silicon.
Cleanups for accel/tcg.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmANt7kdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV/qwQgApfJEYmEURz2ETsBv
z1D/lVM6sjVky7Rk0GiCePf9GZhpXuLK0tEDxWPhHp8d466KfvU3iiXLv0xGbFV5
MBYXPw2uJWLfYNqfi3YGJYSGAdESKJSx27hMMb7RkElbbKqmFGVyPTkZG0VDoiCZ
hEUMGFXa1e0WjTQchm7AUw8CtATHUTmC2wkVqA+Z+BNqoU2WKbvy6f5QgM2CdWEX
bFoC/K0o0vIr8OrwS76ZyVDwbGG7s8r9gA2B9a2Nw73/n4q6DdZPwcUIR23blHa/
A9NmdU4HRNt07nfJN9DQ2qe9utNkoaFj7SpRW2+RJCVkTz5hqbiZTO1c3ZJa0MTi
QbyMNQ==
=KGcn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-tcg-20210124' into staging
Fix tcg constant temp overflow.
Fix running during atomic single-step.
Partial support for apple silicon.
Cleanups for accel/tcg.
# gpg: Signature made Sun 24 Jan 2021 18:08:57 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth-gitlab/tags/pull-tcg-20210124:
tcg: Restart code generation when we run out of temps
tcg: Toggle page execution for Apple Silicon
accel/tcg: Restrict cpu_io_recompile() from other accelerators
accel/tcg: Declare missing cpu_loop_exit*() stubs
accel/tcg: Restrict tb_gen_code() from other accelerators
accel/tcg: Move tb_flush_jmp_cache() to cputlb.c
accel/tcg: Make cpu_gen_init() static
tcg: Optimize inline dup_const for MO_64
qemu/compiler: Split out qemu_build_not_reached_always
tcg: update the cpu running flag in cpu_exec_step_atomic
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU coding convention prefers spaces over tabs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-15-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the codes use hardcoded numbers (0xff/0xfe) for the dummy
value and block start token. Replace them with macros.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-12-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This fixes the wrong command index for STOP_TRANSMISSION, the
required command to interrupt the multiple block read command,
in the old codes. It should be CMD12 (0x4c), not CMD13 (0x4d).
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.2,
"Data Read", there is a minimum 8 clock cycles (Nac) after the card
response and before data block shows up on the data out line. This
applies to both single and multiple block read operations.
Current implementation of single block read already satisfies the
timing requirement as in the RESPONSE state after all responses are
transferred the state remains unchanged. In the next 8 clock cycles
it jumps to DATA_START state if data is ready.
However we need an explicit state when expanding our support to
multiple block read in the future. Let's add a new state PREP_DATA
explicitly in the ssi-sd state machine to represent Nac.
Note we don't change the single block read state machine to let it
jump from RESPONSE state to DATA_START state as that effectively
generates a 16 clock cycles Nac, which might not be safe. As the
spec says the maximum Nac shall be calculated from several fields
encoded in the CSD register, we don't want to bother updating CSD
to ensure our Nac is within range to complicate things.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-9-bmeng.cn@gmail.com>
[PMD: Change VMState version id 4 -> 5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the SD spec, a valid data block is suffixed with a 16-bit CRC
generated by the standard CCITT polynomial x16+x12+x5+1. This part
is currently missing in the ssi-sd state machine. Without it, all
data block transfer fails in guest software because the expected
CRC16 is missing on the data out line.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-8-bmeng.cn@gmail.com>
[PMD: Change VMState version id 3 -> 4,
check s->mode validity in post_load()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Import CRC16 calculation routines from Linux kernel v5.10:
include/linux/crc-ccitt.h
lib/crc-ccitt.c
to QEMU:
include/qemu/crc-ccitt.h
util/crc-ccitt.c
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210123104016.17485-7-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Restrict compilation to system emulation]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
commit f6fb1f9b31 ("sdcard: Correct CRC16 offset in sd_function_switch()")
changed the 16-bit CRC to be stored at offset 64. In fact, this CRC
calculation is completely wrong. From the original codes, it wants
to calculate the CRC16 of the first 64 bytes of sd->data[], however
passing 64 as the `width` to sd_crc16() actually counts 256 bytes
starting from the `message` for the CRC16 calculation, which is not
what we want.
Besides that, it seems existing sd_crc16() algorithm does not match
the SD spec, which says CRC16 is the CCITT one but the calculation
does not produce expected result. It turns out the CRC16 was never
transferred outside the sd core, as in sd_read_byte() we see:
if (sd->data_offset >= 64)
sd->state = sd_transfer_state;
Given above reasons, let's drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Some large translation blocks can generate so many unique
constants that we run out of temps to hold them. In this
case, longjmp back to the start of code generation and
restart with a smaller translation block.
Buglink: https://bugs.launchpad.net/bugs/1912065
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
After the card is put into SPI mode, CRC check for all commands
including CMD0 will be done according to CMD59 setting. But this
command is currently unimplemented. Simply allow the decoding of
CMD59, but the CRC remains unchecked.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.1,
"Command/Response", there is a minimum 8 clock cycles (Ncr) before
the card response shows up on the data out line. However current
implementation jumps directly to the sending response state after
all 6 bytes command is received, which is a spec violation.
Add a new state PREP_RESP in the ssi-sd state machine to handle it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-4-bmeng.cn@gmail.com>
[PMD: Change VMState version id 2 -> 3]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Pages can't be both write and executable at the same time on Apple
Silicon. macOS provides public API to switch write protection [1] for
JIT applications, like TCG.
1. https://developer.apple.com/documentation/apple_silicon/porting_just-in-time_compilers_to_apple_silicon
Tested-by: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20210113032806.18220-1-r.bolshakov@yadro.com>
[rth: Inline the qemu_thread_jit_* functions;
drop the MAP_JIT change for a follow-on patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
As cpu_io_recompile() is only called within TCG accelerator
in cputlb.c, declare it locally.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210117164813.4101761-6-f4bug@amsat.org>
[rth: Adjust vs changed tb_flush_jmp_cache patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
cpu_loop_exit*() functions are declared in accel/tcg/cpu-exec-common.c,
and are not available when TCG accelerator is not built. Add stubs so
linking without TCG succeed.
Problematic files:
- hw/semihosting/console.c in qemu_semihosting_console_inc()
- hw/ppc/spapr_hcall.c in h_confer()
- hw/s390x/ipl.c in s390_ipl_reset_request()
- hw/misc/mips_itu.c
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210117164813.4101761-5-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
tb_gen_code() is only called within TCG accelerator, declare it locally.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210117164813.4101761-4-f4bug@amsat.org>
[rth: Adjust vs changed tb_flush_jmp_cache patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move and make the function static, as the only users
are here in cputlb.c.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
cpu_gen_init() is TCG specific, only used in tcg/translate-all.c.
No need to export it to other accelerators, declare it statically.
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210117164813.4101761-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Options such as "server" or "nowait", that are commonly found in -chardev,
are sugar for "server=on" and "wait=off". This is quite surprising and
also does not have any notion of typing attached. It is even possible to
do "-device e1000,noid" and get a device with "id=off".
Deprecate it and print a warning when it is encountered. In general,
this short form for boolean options only seems to be in wide use for
-chardev and -spice.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, help options are parsed normally and then checked
specially in opt_validate, but only if coming from
qemu_opts_parse_noisily. has_help_option does the check on its own.
opt_validate() has two callers: qemu_opt_set(), which passes null and is
therefore unaffected, and opts_do_parse(), which is affected.
opts_do_parse() is called by qemu_opts_do_parse(), which passes null and
is therefore unaffected, and opts_parse().
opts_parse() is called by qemu_opts_parse() and qemu_opts_set_defaults(),
which pass null and are therefore unaffected, and
qemu_opts_parse_noisily().
Move the check from opt_validate to the parsing workhorse of QemuOpts,
get_opt_name_value. This will come in handy in the next patch, which
will raise a warning for "-object memory-backend-ram,share" ("flag" option
with no =on/=off part) but not for "-object memory-backend-ram,help".
As a result:
- opts_parse and opts_do_parse do not return an error anymore
when help is requested; qemu_opts_parse_noisily does not have
to work around that anymore.
- various crazy ways to request help are not recognized anymore:
- "help=..."
- "nohelp" (sugar for "help=off")
- "?=..."
- "no?" (sugar for "?=off")
- "help" would be recognized as help request even if there is a (foolishly
named) parameter "help". No such parameters exist, though.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Looking at all merge-lists QemuOptsList, here is how they access their
QemuOpts:
reopen_opts in qemu-io-cmds.c ("qemu-img reopen -o")
qemu_opts_find(&reopen_opts, NULL)
empty_opts in qemu-io.c ("qemu-io open -o")
qemu_opts_find(&empty_opts, NULL)
qemu_rtc_opts ("-rtc")
qemu_find_opts_singleton("rtc")
qemu_machine_opts ("-M")
qemu_find_opts_singleton("machine")
qemu_action_opts ("-name")
qemu_opts_foreach->process_runstate_actions
qemu_boot_opts ("-boot")
in hw/nvram/fw_cfg.c and hw/s390x/ipl.c:
QTAILQ_FIRST(&qemu_find_opts("bootopts")->head)
in softmmu/vl.c:
qemu_opts_find(qemu_find_opts("boot-opts"), NULL)
qemu_name_opts ("-name")
qemu_opts_foreach->parse_name
parse_name does not use id
qemu_mem_opts ("-m")
qemu_find_opts_singleton("memory")
qemu_icount_opts ("-icount")
qemu_opts_foreach->do_configure_icount
do_configure_icount->icount_configure
icount_configure does not use id
qemu_smp_opts ("-smp")
qemu_opts_find(qemu_find_opts("smp-opts"), NULL)
qemu_spice_opts ("-spice")
QTAILQ_FIRST(&qemu_spice_opts.head)
i.e. they don't need an id. Sometimes its presence is ignored
(e.g. when using qemu_opts_foreach), sometimes all the options
with the id are skipped, sometimes only the first option on the
command line is considered. -boot does two different things
depending on who's looking at the options.
With this patch we just forbid id on merge-lists QemuOptsLists; if the
command line still works, it has the same semantics as before.
qemu_opts_create's fail_if_exists parameter is now unnecessary:
- it is unused if id is NULL
- opts_parse only passes false if reached from qemu_opts_set_defaults,
in which case this patch enforces that id must be NULL
- other callers that can pass a non-NULL id always set it to true
Assert that it is true in the only case where "fail_if_exists" matters,
i.e. "id && !lists->merge_lists". This means that if an id is present,
duplicates are always forbidden, which was already the status quo.
Discounting the case that aborts as it's not user-controlled (it's
"just" a matter of inspecting qemu_opts_create callers), the paths
through qemu_opts_create can be summarized as:
- merge_lists = true: singleton opts with NULL id; non-NULL id fails
- merge_lists = false: always return new opts; non-NULL id fails if dup
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use qemu_opts_parse_noisily now that HMP does not call
vnc_parse anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210120144235.345983-4-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The HMP command \"change vnc TARGET\" is messy:
- it takes an ugly shortcut to determine if the option has an "id",
with incorrect results if "id=" is not preceded by an unescaped
comma.
- it deletes the existing QemuOpts and does not try to rollback
if the parsing fails (which is not causing problems, but only due to
how VNC options are parsed)
- because it uses the same parsing function as "-vnc", it forces
the latter to not support "-vnc help".
On top of this, it uses a deprecated QMP command, thus getting in
the way of removing the QMP command. Since the usecase for the
command is not clear, just remove it and send "change vnc password"
directly to the QMP "change-vnc-password" command.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210120144235.345983-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The --enable-bzip2/--disable-bzip2 configure arguments are
somehow misleading, they check for the bzip2 library, not
the bzip2 program.
We need the bzip2 program to install the EDK2 firmware blobs
(see commit 623ef637a2 "configure: Check bzip2 is available").
Check if the bzip2 program in the global meson.build to avoid
the configuration to succeed, but a later when trying to install
the firmware blobs:
../pc-bios/meson.build:5:2: ERROR: Program 'bzip2' not found
Reported-by: John Snow <jsnow@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: c8d5450bba ("configure: move install_blobs from configure to meson")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210114174509.2944817-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Globally declare in the main meson.build:
- the list of EDK2 targets,
- whether the EDK2 blobs have to be installed.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210114174509.2944817-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210121095616.1471869-9-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210121095616.1471869-8-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Display block layer information altogether,
when it is relevant.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210121095616.1471869-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Display accelerators and selected targets altogether,
avoid to display unuseful information when not relevant.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210121095616.1471869-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
