It is not used outside hw/vfio/common.c, so it does not need to
be extern.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'dual' sPAPR IRQ backend supports both interrupt mode, XIVE
exploitation mode and the legacy compatibility mode (XICS). both modes
are not supported at the same time.
The machine starts with the legacy mode and a new interrupt mode can
then be negotiated by the CAS process. In this case, the new mode is
activated after a reset to take into account the required changes in
the machine. These impact the device tree layout, the interrupt
presenter object and the exposed MMIO regions in the case of XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit 15ed653fa4 ("ppc/xics: An ICS with offset 0 is assumed to be
uninitialized") introduced an extra check on the ICS offset which is
not strictly necessary.
Revert the change to be able to map the XICS IRQ number space on the
XIVE IRQ number space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Future changes of the ICSState object will remove the qemu_irq array
from under the interrupt controller model. Prepare ground for the PSI
interrupt sources and introduce a new one directly under the PSI
device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug will bring more users for it. Let's define it along with
the PHB defines from which it is derived for simplicity.
While here fix a misleading comment about manual placement, which was
abandoned with 30b3bc5aa9.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds cleanup counterparts to pci_register_root_bus(),
pci_root_bus_new(), and pci_bus_irqs().
These cleanup routines are needed in the case of hotpluggable
PCIHostBridge implementations. Currently we can rely on the
object_unparent()'ing of the PCIHostState recursively unparenting
and cleaning up it's child buses, but we need explicit calls
to also:
1) remove the PCIHostState from pci_host_bridges global list.
otherwise, we risk accessing freed memory when we access
the list later
2) clean up memory allocated in pci_bus_irqs()
Both are handled outside the context of any particular bus or
host bridge's init/realize functions, making it difficult to
avoid the need for explicit cleanup functions without remodeling
how PCIHostBridges are created. So keep it simple and just add
them for now.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used when creating the default PHB. Let's rename
it and move it to the core machine code for clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF receives a device tree and updates it with various properties
before switching to the guest kernel and QEMU is not aware of any changes
made by SLOF. Since there is no real RTAS (QEMU implements it), it makes
sense to pass the SLOF final device tree to QEMU to let it implement
RTAS related tasks better, such as PCI host bus adapter hotplug.
Specifially, now QEMU can find out the actual XICS phandle (for PHB
hotplug) and the RTAS linux,rtas-entry/base properties (for firmware
assisted NMI - FWNMI).
This stores the initial DT blob in the sPAPR machine and replaces it
in the KVMPPC_H_UPDATE_DT (new private hypercall) handler.
This adds an @update_dt_enabled machine property to allow backward
migration.
SLOF already has a hypercall since
https://github.com/aik/SLOF/commit/e6fc84652c9c0073f9183
This makes use of the new fdt_check_full() helper. In order to allow
the configure script to pick the correct DTC version, this adjusts
the DTC presense test.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_HOME_NODE_ASSOCIATIVITY H-Call returns the associativity domain
designation associated with the identifier input parameter
This fixes a crash when we try to hotplug a CPU in memory-less and
CPU-less numa node. In this case, the kernel tries to online the
node, but without the information provided by this h-call, the node id,
it cannot and the CPU is started while the node is not onlined.
It also removes the warning message from the kernel:
VPHN is not supported. Disabling polling..
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x1jv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190107' into staging
target-arm queue:
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
# gpg: Signature made Mon 07 Jan 2019 16:29:52 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190107: (37 commits)
Support u-boot noload images for arm as used by, NetBSD/evbarm GENERIC kernel.
hw/misc/tz-mpc: Fix value of BLK_MAX register
target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
arm: Add Clock peripheral stub to NRF51 SOC
tests/microbit-test: Add Tests for nRF51 Timer
arm: Instantiate NRF51 Timers
hw/timer/nrf51_timer: Add nRF51 Timer peripheral
tests/microbit-test: Add Tests for nRF51 GPIO
arm: Instantiate NRF51 general purpose I/O
hw/gpio/nrf51_gpio: Add nRF51 GPIO peripheral
arm: Instantiate NRF51 random number generator
hw/misc/nrf51_rng: Add NRF51 random number generator peripheral
arm: Add header to host common definition for nRF51 SOC peripherals
qtest: Add set_irq_in command to set IRQ/GPIO level
hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
cpus.c: Fix race condition in cpu_stop_current()
MAINTAINERS: Add ARM-related files for hw/[misc|input|timer]/
hw/arm: versal: Plug memory leaks
Revert "armv7m: Guard against no -kernel argument"
arm/xlnx-zynqmp: put APUs and RPUs in separate CPU clusters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the NRF51 random number generator peripheral.
This is a simple random generator that continuously generates
new random values after startup.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-4-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds the cpu-cluster type. It aims at gathering CPUs from
the same cluster in a machine.
For now it only has a `cluster-id` property.
Documentation in cluster.h written with the help of Peter Maydell.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181207090135.7651-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All globals are now either provided via -global or through -cpu
features (CPU features are implemented by registering globals).
If the global isn't being used, it should warn in either case.
We can thus consider that all global_props are "user-provided"
globals. No need to track this per-globals anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This will allow to apply compat properties on other objects than QDev easily.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_3() function with pc_compat_2_3_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
