DIAGNOSE 0x318 (diag318) is an s390 instruction that allows the storage
of diagnostic information that is collected by the firmware in the case
of hardware/firmware service events.
QEMU handles the instruction by storing the info in the CPU state. A
subsequent register sync will communicate the data to the hypervisor.
QEMU handles the migration via a VM State Description.
This feature depends on the Extended-Length SCCB (els) feature. If
els is not present, then a warning will be printed and the SCLP bit
that allows the Linux kernel to execute the instruction will not be
set.
Availability of this instruction is determined by byte 134 (aka fac134)
bit 0 of the SCLP Read Info block. This coincidentally expands into the
space used for CPU entries, which means VMs running with the diag318
capability may not be able to read information regarding all CPUs
unless the guest kernel supports an extended-length SCCB.
This feature is not supported in protected virtualization mode.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-9-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As more features and facilities are added to the Read SCP Info (RSCPI)
response, more space is required to store them. The space used to store
these new features intrudes on the space originally used to store CPU
entries. This means as more features and facilities are added to the
RSCPI response, less space can be used to store CPU entries.
With the Extended-Length SCCB (ELS) facility, a KVM guest can execute
the RSCPI command and determine if the SCCB is large enough to store a
complete reponse. If it is not large enough, then the required length
will be set in the SCCB header.
The caller of the SCLP command is responsible for creating a
large-enough SCCB to store a complete response. Proper checking should
be in place, and the caller should execute the command once-more with
the large-enough SCCB.
This facility also enables an extended SCCB for the Read CPU Info
(RCPUI) command.
When this facility is enabled, the boundary violation response cannot
be a result from the RSCPI, RSCPI Forced, or RCPUI commands.
In order to tolerate kernels that do not yet have full support for this
feature, a "fixed" offset to the start of the CPU Entries within the
Read SCP Info struct is set to allow for the original 248 max entries
when this feature is disabled.
Additionally, this is introduced as a CPU feature to protect the guest
from migrating to a machine that does not support storing an extended
SCCB. This could otherwise hinder the VM from being able to read all
available CPU entries after migration (such as during re-ipl).
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-7-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200921221045.699690-13-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of setting CPUState::halted to 1 in s390_cpu_initfn(), use the
start-powered-off property which makes cpu_common_reset() initialize it
to 1 in common code.
Note that this changes behavior by setting cs->halted to 1 on reset, which
didn't happen before.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Message-Id: <20200826055535.951207-9-bauerman@linux.ibm.com>
[dwg: Fix from Laurent Vivier for user only case]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The binaries move to the root directory, e.g. qemu-system-i386 or
qemu-arm. This requires changes to qtests, CI, etc.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to hw_arch, each architecture defines two sourceset which are placed in
dictionaries target_arch and target_softmmu_arch. These are then picked up
from there when building the per-emulator static_library.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Needed by linux-user/s390x/cpu_loop.c; this removes the only use of HOST_CC.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With Makefiles that have automatically generated dependencies, you
generated includes are set as dependencies of the Makefile, so that they
are built before everything else and they are available when first
building the .c files.
Alternatively you can use a fine-grained dependency, e.g.
target/arm/translate.o: target/arm/decode-neon-shared.inc.c
With Meson you have only one choice and it is a third option, namely
"build at the beginning of the corresponding target"; the way you
express it is to list the includes in the sources of that target.
The problem is that Meson decides if something is a source vs. a
generated include by looking at the extension: '.c', '.cc', '.m', '.C'
are sources, while everything else is considered an include---including
'.inc.c'.
Use '.c.inc' to avoid this, as it is consistent with our other convention
of using '.rst.inc' for included reStructuredText files. The editorconfig
file is adjusted.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
The output is 128-bit, and thus requires a pair of 64-bit temps.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Buglink: https://bugs.launchpad.net/bugs/1883984
Message-Id: <20200620042140.42070-1-richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The schib region can be used to obtain the latest SCHIB from the host
passthrough subchannel. Since the guest SCHIB is virtualized,
we currently only update the path related information so that the
guest is aware of any path related changes when it issues the
'stsch' instruction.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505125757.98209-4-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As these declarations are restricted to !CONFIG_USER_ONLY in
helper.c, only declare them when system-mode emulation is used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-8-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
All this code is guarded checking CONFIG_USER_ONLY definition.
Drop the duplicated checks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-7-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The decode_basedisp*() methods are only used in ioinst.c,
which is only build in system-mode emulation.
I/O instructions are privileged, and other S instructions
are decoded elsewhere.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200526172427.17460-6-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We need some little help in the code to reduce the valgrind noise.
This patch does this with some designated initializers for the cpu
model features and subfunctions.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200429074201.100924-1-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Merge VERLL and VERLLV into op_vesv and op_ves, alongside
all of the other vector shift operations.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit e47970f51d "s390x/cpumodel: Fix query-cpu-model-FOO error API
violations" neglected to change visit_check_struct()'s Error **
argument along with the others. If visit_check_struct() failed, we'd
take the success path. Fortunately, it can't fail here:
qobject_input_check_struct() checks we consumed the whole dictionary,
and to get here, we did. Fix it anyway.
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200505101908.6207-4-armbru@redhat.com>
Replace the float64 compare specializations with inline functions
that call the standard float64_compare{,_quiet} functions.
Use bool as the return type.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Give the previously unnamed enum a typedef name. Use it in the
prototypes of compare functions. Use it to hold the results
of the compare functions.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
Both s390_features[S390_FEAT_PCC_CMAC_AES_256].name and
s390_features[S390_FEAT_PCC_CMAC_EAES_256].name is
"pcc-cmac-eaes-256". The former is obviously a pasto.
Impact:
* s390_feat_bitmap_to_ascii() misidentifies S390_FEAT_PCC_CMAC_AES_256
as "pcc-cmac-eaes-256". Affects QMP commands query-cpu-definitions,
query-cpu-model-expansion, query-cpu-model-baseline,
query-cpu-model-comparison, and the error message when
s390_realize_cpu_model() fails in check_compatibility().
* s390_cpu_list() also misidentifies it. Affects -cpu help.
* s390_cpu_model_register_props() creates CPU property
"pcc-cmac-eaes-256" twice. The second one fails, but the error is
ignored (a later commit will change that). Results in a single
property "pcc-cmac-eaes-256" with the description for
S390_FEAT_PCC_CMAC_AES_256, and no property for
S390_FEAT_PCC_CMAC_EAES_256. CPU properties are visible in CLI -cpu
and -device, QMP & HMP device_add, QMP device-list-properties, and
QOM introspection.
The two features are almost always used via their group msa4. Such
use is not affected by this bug.
Fix by deleting the wayward 'e'.
Fixes: 7824174462 ("s390x/cpumodel: introduce CPU features")
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: David Hildenbrand <david@redhat.com>
Cc: qemu-s390x@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20200505152926.18877-10-armbru@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[Lost paragraph in commit message restored, Fixes: tweaked]
object_property_set_description() and
object_class_property_set_description() fail only when property @name
is not found.
There are 85 calls of object_property_set_description() and
object_class_property_set_description(). None of them can fail:
* 84 immediately follow the creation of the property.
* The one in spapr_rng_instance_init() refers to a property created in
spapr_rng_class_init(), from spapr_rng_properties[].
Every one of them still gets to decide what to pass for @errp.
51 calls pass &error_abort, 32 calls pass NULL, one receives the error
and propagates it to &error_abort, and one propagates it to
&error_fatal. I'm actually surprised none of them violates the Error
API.
What are we gaining by letting callers handle the "property not found"
error? Use when the property is not known to exist is simpler: you
don't have to guard the call with a check. We haven't found such a
use in 5+ years. Until we do, let's make life a bit simpler and drop
the @errp parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-8-armbru@redhat.com>
[One semantic rebase conflict resolved]
The gen_gvec_dupi switch is unnecessary with the new function.
Replace it with a local gen_gvec_dup_imm that takes care of the
register to offset conversion and length arguments.
Drop zero_vec and use use gen_gvec_dup_imm with 0.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The unpack facility is an indication that diagnose 308 subcodes 8-10
are available to the guest. That means, that the guest can put itself
into protected mode.
Once it is in protected mode, the hardware stops any attempt of VM
introspection by the hypervisor.
Some features are currently not supported in protected mode:
* vfio devices
* Migration
* Huge page backings
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-17-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
For protected VMs status storing is not done by QEMU anymore.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-15-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
For protected guests, we need to put the IO emulation results into the
SIDA, so SIE will write them into the guest at the next entry.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-14-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
IO instruction data is routed through SIDAD for protected guests, so
adresses do not need to be checked, as this is kernel memory which is
always available.
Also the instruction data always starts at offset 0 of the SIDAD.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-13-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
For protected guests the IPIB is written/read to/from the SIDA, so we
need those accesses to go through s390_cpu_pv_mem_read/write().
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-12-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Handling of CPU reset and setting of the IPL psw from guest storage at
offset 0 is done by a Ultravisor call. Let's only fetch it if
necessary.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-11-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
SCLP for a protected guest is done over the SIDAD, so we need to use
the s390_cpu_pv_mem_* functions to access the SIDAD instead of guest
memory when reading/writing SCBs.
To not confuse the sclp emulation, we set 0x4000 as the SCCB address,
since the function that injects the sclp external interrupt would
reject a zero sccb address.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20200319131921.2367-10-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
For protected guests, we need to put the STSI emulation results into
the SIDA, so SIE will write them into the guest at the next entry.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-9-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Protected guests save the instruction control blocks in the SIDA
instead of QEMU/KVM directly accessing the guest's memory.
Let's introduce new functions to access the SIDA.
The memops for doing so are available with KVM_CAP_S390_PROTECTED, so
let's check for that.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-8-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Protected VMs no longer intercept with code 4 for an instruction
interception. Instead they have codes 104 and 108 for protected
instruction interception and protected instruction notification
respectively.
The 104 mirrors the 4 interception.
The 108 is a notification interception to let KVM and QEMU know that
something changed and we need to update tracking information or
perform specific tasks. It's currently taken for the following
instructions:
* spx (To inform about the changed prefix location)
* sclp (On incorrect SCCB values, so we can inject a IRQ)
* sigp (All but "stop and store status")
* diag308 (Subcodes 0/1)
Of these exits only sclp errors, state changing sigps and diag308 will
reach QEMU. QEMU will do its parts of the job, while the ultravisor
has done the instruction part of the job.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200319131921.2367-7-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The unpack facility provides the means to setup a protected guest. A
protected guest cannot be introspected by the hypervisor or any
user/administrator of the machine it is running on.
Protected guests are encrypted at rest and need a special boot
mechanism via diag308 subcode 8 and 10.
Code 8 sets the PV specific IPLB which is retained separately from
those set via code 5.
Code 10 is used to unpack the VM into protected memory, verify its
integrity and start it.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Co-developed-by: Christian Borntraeger <borntraeger@de.ibm.com> [Changes
to machine]
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200323083606.24520-1-frankja@linux.ibm.com>
[CH: fixed up KVM_PV_VM_ -> KVM_PV_]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
They are part of the IPL process, so let's put them into the ipl
header.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200319131921.2367-2-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The cpu number reporting is handled by KVM and QEMU only fills in the
VM name, uuid and other values.
Unfortunately KVM doesn't report reserved cpus and doesn't even know
they exist until the are created via the ioctl.
So let's fix up the cpu values after KVM has written its values to the
3.2.2 sysib. To be consistent, we use the same code to retrieve the cpu
numbers as the STSI TCG code in target/s390x/misc_helper.c:HELPER(stsi).
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200331110123.3774-1-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Bug fixes:
* memory encryption: Disable mem merge
(Dr. David Alan Gilbert)
Features:
* New EPYC CPU definitions (Babu Moger)
* Denventon-v2 CPU model (Tao Xu)
* New 'note' field on versioned CPU models (Tao Xu)
Cleanups:
* x86 CPU topology cleanups (Babu Moger)
* cpu: Use DeviceClass reset instead of a special CPUClass reset
(Peter Maydell)
-----BEGIN PGP SIGNATURE-----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=9fEL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-and-machine-pull-request' into staging
x86 and machine queue for 5.0 soft freeze
Bug fixes:
* memory encryption: Disable mem merge
(Dr. David Alan Gilbert)
Features:
* New EPYC CPU definitions (Babu Moger)
* Denventon-v2 CPU model (Tao Xu)
* New 'note' field on versioned CPU models (Tao Xu)
Cleanups:
* x86 CPU topology cleanups (Babu Moger)
* cpu: Use DeviceClass reset instead of a special CPUClass reset
(Peter Maydell)
# gpg: Signature made Wed 18 Mar 2020 01:16:43 GMT
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-and-machine-pull-request:
hw/i386: Rename apicid_from_topo_ids to x86_apicid_from_topo_ids
hw/i386: Update structures to save the number of nodes per package
hw/i386: Remove unnecessary initialization in x86_cpu_new
machine: Add SMP Sockets in CpuTopology
hw/i386: Consolidate topology functions
hw/i386: Introduce X86CPUTopoInfo to contain topology info
cpu: Use DeviceClass reset instead of a special CPUClass reset
machine/memory encryption: Disable mem merge
hw/i386: Rename X86CPUTopoInfo structure to X86CPUTopoIDs
i386: Add 2nd Generation AMD EPYC processors
i386: Add missing cpu feature bits in EPYC model
target/i386: Add new property note to versioned CPU models
target/i386: Add Denverton-v2 (no MPX) CPU model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- docker updates for VirGL
- re-factor gdbstub for static GDBState
- re-factor gdbstub for dynamic arrays
- add SVE support to arm gdbstub
- add some guest debug tests to check-tcg
- add aarch64 userspace register tests
- remove packet size limit to gdbstub
- simplify gdbstub monitor code
- report vContSupported in gdbstub to use proper single-step
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl5xDUIACgkQ+9DbCVqe
KkQwCwf/YtmUsNxxO+CgNctq2u3jV4FoOdQP3bejvmT2+cigKJhQuBlWPg1/YsqF
RDNkmBQx2JaVVMuVmpnwVK1UD+kmYZqrtlOkPNcVrjPmLCq3BVI1LHe6Rjoerx8F
QoZyH0IMNHbBgDo1I46lSFOWcxmOvo+Ow7NX5bPKwlRzf0dyEqSJahRaZLAgUscR
taTtGfk9uQsnxoRsvH/efiQ4bZtUvrEQuhEX3WW/yVE1jTpcb2llwX4xONJb2It3
/0WREGEEIT8PpnWw2S3FH4THY/BjWgz/FPDwNNZYCKBMWDjuG/8KHryd738T9rzo
lkGP9YcXmiyxMMyFFwS8RD3SHr8LvQ==
=Wm+a
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-gdbstub-170320-1' into staging
Testing and gdbstub updates:
- docker updates for VirGL
- re-factor gdbstub for static GDBState
- re-factor gdbstub for dynamic arrays
- add SVE support to arm gdbstub
- add some guest debug tests to check-tcg
- add aarch64 userspace register tests
- remove packet size limit to gdbstub
- simplify gdbstub monitor code
- report vContSupported in gdbstub to use proper single-step
# gpg: Signature made Tue 17 Mar 2020 17:47:46 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-gdbstub-170320-1: (28 commits)
gdbstub: Fix single-step issue by confirming 'vContSupported+' feature to gdb
gdbstub: do not split gdb_monitor_write payload
gdbstub: change GDBState.last_packet to GByteArray
tests/tcg/aarch64: add test-sve-ioctl guest-debug test
tests/tcg/aarch64: add SVE iotcl test
tests/tcg/aarch64: add a gdbstub testcase for SVE registers
tests/guest-debug: add a simple test runner
configure: allow user to specify what gdb to use
tests/tcg/aarch64: userspace system register test
target/arm: don't bother with id_aa64pfr0_read for USER_ONLY
target/arm: generate xml description of our SVE registers
target/arm: default SVE length to 64 bytes for linux-user
target/arm: explicitly encode regnum in our XML
target/arm: prepare for multiple dynamic XMLs
gdbstub: extend GByteArray to read register helpers
target/i386: use gdb_get_reg helpers
target/m68k: use gdb_get_reg helpers
target/arm: use gdb_get_reg helpers
gdbstub: add helper for 128 bit registers
gdbstub: move mem_buf to GDBState and use GByteArray
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPUClass has a 'reset' method. This is a legacy from when
TYPE_CPU used not to inherit from TYPE_DEVICE. We don't need it any
more, as we can simply use the TYPE_DEVICE reset. The 'cpu_reset()'
function is kept as the API which most places use to reset a CPU; it
is now a wrapper which calls device_cold_reset() and then the
tracepoint function.
This change should not cause CPU objects to be reset more often
than they are at the moment, because:
* nobody is directly calling device_cold_reset() or
qdev_reset_all() on CPU objects
* no CPU object is on a qbus, so they will not be reset either
by somebody calling qbus_reset_all()/bus_cold_reset(), or
by the main "reset sysbus and everything in the qbus tree"
reset that most devices are reset by
Note that this does not change the need for each machine or whatever
to use qemu_register_reset() to arrange to call cpu_reset() -- that
is necessary because CPU objects are not on any qbus, so they don't
get reset when the qbus tree rooted at the sysbus bus is reset, and
this isn't being changed here.
All the changes to the files under target/ were made using the
included Coccinelle script, except:
(1) the deletion of the now-inaccurate and not terribly useful
"CPUClass::reset" comments was done with a perl one-liner afterwards:
perl -n -i -e '/ CPUClass::reset/ or print' target/*/*.c
(2) this bit of the s390 change was done by hand, because the
Coccinelle script is not sophisticated enough to handle the
parent_reset call being inside another function:
| @@ -96,8 +96,9 @@ static void s390_cpu_reset(CPUState *s, cpu_reset_type type)
| S390CPU *cpu = S390_CPU(s);
| S390CPUClass *scc = S390_CPU_GET_CLASS(cpu);
| CPUS390XState *env = &cpu->env;
|+ DeviceState *dev = DEVICE(s);
|
|- scc->parent_reset(s);
|+ scc->parent_reset(dev);
| cpu->env.sigp_order = 0;
| s390_cpu_set_state(S390_CPU_STATE_STOPPED, cpu);
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200303100511.5498-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of passing a pointer to memory now just extend the GByteArray
to all the read register helpers. They can then safely append their
data through the normal way. We don't bother with this abstraction for
write registers as we have already ensured the buffer being copied
from is the correct size.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-Id: <20200316172155.971-15-alex.bennee@linaro.org>
Description copied from Linux kernel commit from Gustavo A. R. Silva
(see [3]):
--v-- description start --v--
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to
declare variable-length types such as these ones is a flexible
array member [1], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler
warning in case the flexible array does not occur last in the
structure, which will help us prevent some kind of undefined
behavior bugs from being unadvertenly introduced [2] to the
Linux codebase from now on.
--^-- description end --^--
Do the similar housekeeping in the QEMU codebase (which uses
C99 since commit 7be41675f7).
All these instances of code were found with the help of the
following command (then manual analysis, without modifying
structures only having a single flexible array member, such
QEDTable in block/qed.h):
git grep -F '[0];'
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=76497732932f
[3] https://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux.git/commit/?id=17642a2fbd2c1
Inspired-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's nicer to just call one function than calling a function for each
possible iplb type.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200310090950.61172-1-frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's rename PSW_MASK_ESA_ADDR to PSW_MASK_SHORT_ADDR because we're
not working with a ESA PSW which would not support the extended
addressing bit. Also let's actually use it.
Additionally we introduce PSW_MASK_SHORT_CTRL and use it throughout
the codebase.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200227092341.38558-1-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There is a special quiesce PSW that we check for "shutdown". Otherwise disabled
wait is detected as "crashed". Architecturally we must only check PSW bits
116-127. Fix this.
Cc: qemu-stable@nongnu.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1582204582-22995-1-git-send-email-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Up to now we only had an ioctl to reset vcpu data QEMU couldn't reach
for the initial reset, which was also called for the clear reset. To
be architecture compliant, we also need to clear local interrupts on a
normal reset.
Because of this and the upcoming protvirt support we need to add
ioctls for the missing clear and normal resets.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200214151636.8764-3-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
RNSBG is handled via the op_rosbg() helper function. But RNSBG has
the opcode 0xEC54, i.e. 0x54 as second byte, while op_rosbg() currently
checks for 0x55. This seems to be a typo, fix it to use 0x54 instead,
so that op_rosbg() does not abort() anymore if a program uses RNSBG.
I've checked with a simple test function that I now get the same results
with KVM and with TCG:
static void test_rnsbg(void)
{
uint64_t r1, r2;
r2 = 0xffff000000000000UL;
r1 = 0x123456789bdfaaaaUL;
asm volatile (" rnsbg %0,%1,12,61,16 " : "+r"(r1) : "r"(r2));
printf("r1 afterwards: 0x%lx\n", r1);
}
Buglink: https://bugs.launchpad.net/qemu/+bug/1860920
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200130133417.10531-1-thuth@redhat.com>
Fixes: d6c6372e18 ("target-s390: Implement R[NOX]SBG")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Use an explicit boolean type.
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Two lines in hw/net/dp8393x.c that Coccinelle produced that
were over 80 characters were re-wrapped by hand.
Suggested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The logic was inverted and reported running if the cpu was stopped.
Let's fix that.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Fixes: d1b468bc88 ("s390x/tcg: implement SIGP SENSE RUNNING STATUS")
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200124134818.9981-1-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The separate pointer is now redundant.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200123232248.1800-6-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
I believe that the separate allocation of DisasFields from DisasContext
was meant to limit the places from which we could access fields. But
that plan did not go unchanged, and since DisasContext contains a pointer
to fields, the substructure is accessible everywhere.
By allocating the substructure with DisasContext, we improve the locality
of the accesses by avoiding one level of pointer chasing. In addition,
we avoid a dangling pointer to stack allocated memory, diagnosed by static
checkers.
Launchpad: https://bugs.launchpad.net/bugs/1661815
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200123232248.1800-5-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
All callers pass s->fields, so we might as well pass s directly.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200123232248.1800-4-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The DisasFields data is available from DisasContext.
We do not need to pass a separate argument.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200123232248.1800-3-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We will want to include the struct in DisasContext.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200123232248.1800-2-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The AIS feature has been disabled late in the v2.10 development cycle since
there were some issues with migration (see commit 3f2d07b3b0 -
"s390x/ais: for 2.10 stable: disable ais facility"). We originally wanted
to enable it again for newer machine types, but apparently we forgot to do
this so far. Let's do it now for the machines that support proper CPU models.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1756946
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200122101437.5069-1-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit ae71ed8610 replaced the use of global max_cpus variable
with a machine property, but introduced a unnecessary ifdef, as
this block is already in the 'not CONFIG_USER_ONLY' branch part:
86 #if defined(CONFIG_USER_ONLY)
87
...
106 #else /* !CONFIG_USER_ONLY */
107
...
292 static void do_ext_interrupt(CPUS390XState *env)
293 {
...
313 #ifndef CONFIG_USER_ONLY
314 MachineState *ms = MACHINE(qdev_get_machine());
315 unsigned int max_cpus = ms->smp.max_cpus;
316 #endif
To ease code review, remove the duplicated preprocessor macro,
and move the declarations at the beginning of the statement.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200121110349.25842-6-philmd@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Convert all targets to use cpu_class_set_parent_reset() with the following
coccinelle script:
@@
type CPUParentClass;
CPUParentClass *pcc;
CPUClass *cc;
identifier parent_fn;
identifier child_fn;
@@
+cpu_class_set_parent_reset(cc, child_fn, &pcc->parent_fn);
-pcc->parent_fn = cc->reset;
...
-cc->reset = child_fn;
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <157650847817.354886.7047137349018460524.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We currently search both the root and the tcg/ directories for tcg
files:
$ git grep '#include "tcg/' | wc -l
28
$ git grep '#include "tcg[^/]' | wc -l
94
To simplify the preprocessor search path, unify by expliciting the
tcg/ directory.
Patch created mechanically by running:
$ for x in \
tcg.h tcg-mo.h tcg-op.h tcg-opc.h \
tcg-op-gvec.h tcg-gvec-desc.h; do \
sed -i "s,#include \"$x\",#include \"tcg/$x\"," \
$(git grep -l "#include \"$x\""); \
done
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200101112303.20724-2-philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The generated functions aside from *_real are unused.
The *_real functions have a couple of users in mem_helper.c;
use *_mmuidx_ra instead, with MMU_REAL_IDX.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v2: Use *_mmuidx_ra directly, without intermediate macros.
Code movement in an upcoming patch will show that this file
was implicitly depending on tcg.h being included indirectly.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We need to actually fetch the cpu mask and set it. As we invert the
short psw indication in the mask, SIE will report a specification
exception, if it wasn't present in the reset psw.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191129142025.21453-2-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
These are trivially done by performing a memory operation
with the correct mmu_idx. The only tricky part is using
get_address directly in order to get the address wrapped;
we cannot use la2 because of the format.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191211203614.15611-3-richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Split the PER handling for store-to-real-address into its
own helper function, conditionally called when PER is
enabled, just as we do for per_branch and per_ifetch.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191211203614.15611-2-richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The KVMState struct is opaque, so provide accessors for the fields
that will be moved from current_machine to the accelerator. For now
they just forward to the machine object, but this will change.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to CPU and machine classes, "-accel" class names are mangled,
so we have to first get a class via accel_find and then instantiate it.
Provide a new function to instantiate a class without going through
object_class_get_name, and use it for CPUs and machines already.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We neglected to clean up pending interrupts and emergency signals;
fix that.
Message-Id: <20191206135404.16051-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
qmp_query_cpu_definitions() passes @errp to get_max_cpu_model(), then
frees any error it gets back. This effectively ignores errors.
Dereferencing @errp is wrong; see the big comment in error.h. Passing
@errp is also wrong, because it works only as long as @errp is neither
@error_fatal nor @error_abort. Introduced in commit 38cba1f4d8
"s390x: return unavailable features via query-cpu-definitions".
No caller actually passes such @errp values.
Fix anyway: simply pass NULL to get_max_cpu_model().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-16-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
cpu_model_from_info() is a helper for qmp_query_cpu_model_expansion(),
qmp_query_cpu_model_comparison(), qmp_query_cpu_model_baseline(). It
dereferences @errp when the visitor or the QOM setter fails. That's
wrong; see the big comment in error.h. Introduced in commit
137974cea3 's390x/cpumodel: implement QMP interface
"query-cpu-model-expansion"'.
Its three callers have the same issue. Introduced in commit
4e82ef0502 's390x/cpumodel: implement QMP interface
"query-cpu-model-comparison"' and commit f1a47d08ef 's390x/cpumodel:
implement QMP interface "query-cpu-model-baseline"'.
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-15-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
get_max_cpu_model() dereferences @errp when
kvm_s390_get_host_cpu_model() fails, apply_cpu_model() dereferences it
when kvm_s390_apply_cpu_model() fails, and s390_realize_cpu_model()
dereferences it when get_max_cpu_model() or check_compatibility()
fail. That's wrong; see the big comment in error.h. All three
introduced in commit 80560137cf "s390x/cpumodel: check and apply the
CPU model".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-14-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390x-cpu property setters set_feature() and set_feature_group()
dereference @errp when the visitor fails. That's wrong; see the big
comment in error.h. Introduced in commit 0754f60429 "s390x/cpumodel:
expose features and feature groups as properties".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-13-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As it turns out we need to clear the ri controls and PSW enablement
bit to be architecture compliant.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20191203132813.2734-4-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
It defaults to returning 0 anyway and that return value is not
necessary, as 0 is also the default rc that the caller would return.
While doing that we can simplify the logic a bit and return early if
we inject a PGM exception.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191129091713.4582-1-frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's improve readability by:
* Using constants for the subcodes
* Moving parameter checking into a function
* Removing subcode > 6 check as the default case catches that
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191127175046.4911-6-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's also move the clear reset function into the reset handler.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20191127175046.4911-5-frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move the intial reset into the reset handler and cleanup
afterwards.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191128083723.11937-1-frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's start moving the cpu reset functions into a single function with
a switch/case, so we can later use fallthroughs and share more code
between resets.
This patch introduces the reset function by renaming cpu_reset().
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191127175046.4911-3-frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We have to set the default model of all machine classes, not just for
the active one. Otherwise, "query-machines" will indicate the wrong
CPU model ("qemu-s390x-cpu" instead of "host-s390x-cpu") as
"default-cpu-type".
Doing a
{"execute":"query-machines"}
under KVM now results in
{"return": [
{
"hotpluggable-cpus": true,
"name": "s390-ccw-virtio-4.0",
"numa-mem-supported": false,
"default-cpu-type": "host-s390x-cpu",
"cpu-max": 248,
"deprecated": false},
{
"hotpluggable-cpus": true,
"name": "s390-ccw-virtio-2.7",
"numa-mem-supported": false,
"default-cpu-type": "host-s390x-cpu",
"cpu-max": 248,
"deprecated": false
} ...
Libvirt probes all machines via "-machine none,accel=kvm:tcg" and will
currently see the wrong CPU model under KVM.
Reported-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Fixes: b6805e127c ("s390x: use generic cpu_model parsing")
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021100515.6978-1-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The numbers are unsigned, the computation is wrong. "Each operand is
treated as an unsigned binary integer".
Let's implement as given in the PoP:
"A subtraction is performed by adding the contents of the second operand
with the bitwise complement of the third operand along with a borrow
indication from the rightmost bit of the fourth operand."
Reuse gen_accc2_i64().
Fixes: bc725e6515 ("s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW COMPUTE BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-7-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Testing this, there seems to be something messed up. We are dealing with
unsigned numbers. "Each operand is treated as an unsigned binary integer."
Let's just implement as written in the PoP:
"A subtraction is performed by adding the contents of
the second operand with the bitwise complement of
the third operand along with a borrow indication from
the rightmost bit position of the fourth operand and
the result is placed in the first operand."
We can reuse gen_ac2_i64().
Fixes: 48390a7c27 ("s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-6-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Looks like my idea of what a "borrow" is was wrong. The PoP says:
"If the resulting subtraction results in a carry out of bit zero, a value
of one is placed in the corresponding element of the first operand;
otherwise, a value of zero is placed in the corresponding element"
As clarified by Richard, all we have to do is invert the result.
Fixes: 1ee2d7ba72 ("s390x/tcg: Implement VECTOR SUBTRACT COMPUTE BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-5-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We forgot to propagate the highest bit accross the high doubleword in
two cases (shift >=64).
Fixes: 5f724887e3 ("s390x/tcg: Implement VECTOR SHIFT RIGHT ARITHMETIC")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We missed that we always read a "double-wide even-odd element
pair of the fourth operand". Fix it in all four variants.
Fixes: 1b430aec41 ("s390x/tcg: Implement VECTOR MULTIPLY AND ADD *")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We have to read from odd offsets.
Fixes: 2bf3ee38f1 ("s390x/tcg: Implement VECTOR MULTIPLY *")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
