This patch sets is_default to 1 for puv3 machine, so that
find_default_machine() returns puv3 machine.
Thanks Dunrong for pointing it out.
Cc: Dunrong Huang <riegamaths@gmail.com>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds puv3 dma (Direct Memory Access) support,
include dma device simulation for kernel booting.
v1->v2: Add initialization to ret in puv3_dma_read.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds puv3 pm (power management) support,
include pm device simulation for kernel booting.
Thank Blue Swirl for pointing out the missing "break".
v1->v2: Add initialization to ret in puv3_pm_read.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds puv3 gpio (General Purpose Input/Output) support,
include gpio device simulation and its interrupt support.
v1->v2: Add initialization to ret in puv3_gpio_read.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds puv3 ostimer support, include os timer
device simulation and ptimer support in puv3 machine.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds puv3 interrupt support, include interrupt controler
device simulation and interrupt handler in puv3 machine.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch only add puv3 soc/board support, which introduces puv3
machine description, and specifies console type.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch adds unicore32-softmmu build support, include configure,
makefile, arch_init, and all missing functions needed by softmmu.
Although all missing functions are empty, unicore32-softmmu could
be build successfully.
By 20120804: change QEMU_ARCH_UNICORE32 to 0x4000
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If the guest does not support flushes, we should run in writethrough mode.
The setting is temporary until the next reset, so that for example the
BIOS will run in writethrough mode while Linux will run with a writeback
cache.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Also rename VIRTIO_BLK_F_WCACHE to VIRTIO_BLK_F_WCE for consistency with
the spec.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I noticed that in hw/ide/ahci:ahci_dma_rw_buf() we do not free the sglist. Thus,
I've added a call to qemu_sglist_destroy() to fix this memory leak.
In addition, I've adeed a call in qemu_sglist_destroy() to 0 all of the sglist
fields, in case there is some other codepath that tries to free the sglist.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
While testing q35, which has its cdrom attached to the ahci controller, I found
that the Fedora 17 install would panic on boot. The panic occurs while
squashfs is trying to read from the cdrom. The errors are:
[ 8.622711] SQUASHFS error: xz_dec_run error, data probably corrupt
[ 8.625180] SQUASHFS error: squashfs_read_data failed to read block
0x20be48a
I was also able to produce corrupt data reads using an installed piix based
qemu machine, using 'dd'. I found that the corruptions were only occuring when
then read size was greater than 128k. For example, the following command
results in corrupted reads:
dd if=/dev/sr0 of=/tmp/blah bs=256k iflag=direct
The > 128k size reads exercise a different code path than 128k and below. In
ide_atapi_cmd_read_dma_cb() s->io_buffer_size is capped at 128k. Thus,
ide_atapi_cmd_read_dma_cb() is called a second time when the read is > 128k.
However, ahci_dma_rw_buf() restart the read from offset 0, instead of at 128k.
Thus, resulting in a corrupted read.
To fix this, I've introduced 'io_buffer_offset' field in IDEState to keep
track of the offset. I've also modified ahci_populate_sglist() to take a new
3rd offset argument, so that the sglist is property initialized.
I've tested this patch using 'dd' testing, and Fedora 17 now correctly boots
and installs on q35 with the cdrom ahci controller.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The scsi passthrough handler falls through after completing a
request into the failure path, resulting in a use after free.
Reproducible by running a guest with aio=native on a block device.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fixes the following error:
$ qemu-system-xtensa -cpu help
Segmentation fault
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This makes usable default for -cpu option both for qemu-system-xtensa
and qemu-system-xtensaeb fixing the following error:
$ qemu-system-xtensaeb -M sim
Unable to find CPU definition
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
LOAD_UNLOAD and START_STOP have same value, so the table
entry is initialized twice. Spotted by Clang compiler.
Remove LOAD_UNLOAD entry since START_STOP entry already
represents both.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The qemu_irq for Terminal Count (TC) line between FDC and Slavio misc
device was created only after use, spotted by Clang compiler. Also,
it was not created if the FDC didn't exist.
Rearrange code to fix order. Always create the TC line.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Difference with AMD PCscsi is that DC-390 contains a EEPROM,
and that a romfile is available to add INT13 support.
This has been successfully tested on:
- MS DOS 6.22 (using DC390 ASPI driver)
- MS Windows 98 SE (using DC390 driver)
- MS Windows NT 3.1 (using DC390 driver)
- MS Windows NT 4.0 (using DC390 driver)
- hard disk and cdrom boot
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit 0883c5159f.
Those stubs were only used by PCI ESP emulation, which is now
not compiled on architectures which have no PCI bus support.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
sparc machines loose ability to instanciate PCI ESP SCSI adapter,
which is not a big loose as they don't have PCI bus support.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The unmap command can reuse the same infrastructure as MODE SELECT
for reading the descriptor list into memory. The descriptors are
processed sequentially.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Leaving the aiocb to a non-NULL value leads to an assertion failure when
rerror/werror are set to stop or enospc, and the operation is retried.
scsi-disk checks that the aiocb member is NULL before filling it.
This patch correctly resets the aiocb to NULL values everywhere,
and adds the dual assertion that the aiocb was non-NULL before
calling bdrv_acct_done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Decouple another x86-specific assumption about what irqchips imply.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_allows_irq0_override() is a totally x86 specific concept:
move it to the target-specific source file where it belongs.
This means we need a new header file for the prototype:
kvm_i386.h, in line with the existing kvm_ppc.h.
While we are moving it, fix the return type to be 'bool' rather
than 'int'.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Rename the function kvm_irqchip_set_irq() to kvm_set_irq(),
since it can be used for sending (asynchronous) interrupts whether
there is a full irqchip model in the kernel or not. (We don't
include 'async' in the function name since asynchronous is the
normal case.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch fixes a problem in handling task management functions
in virtio-scsi. The cause of the problem is a mismatch between
the size of the tag in QEMU (32-bit) and virtio-scsi (64-bit).
Changing the QEMU size is hard because the migration format
uses 32 bits to store the tag; so just don't use the QEMU tag
(virtio-scsi only uses the tag for task management functions
anyway) and look up the full 64-bit tag in the hba_private field.
The reproducer is a bit obscure. If you cause an I/O timeout
(for example with rerror=stop and doing 'cont' on the monitor
continuously without fixing the error), sooner or later the
guest will try to abort the command and reissue it. At this
point, QEMU will report _two_ errors instead of one when you
hit 'c', because the first error has not been canceled correctly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 5931065907 is incomplete,
we'll arrive in the scsi command complete callback in CSW state
and must handle that case correctly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Legacy -drive cyls=... are now ignored completely when the drive
doesn't back a hard disk device. Before, they were first checked
against a hard disk's limits, then ignored.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit b1f416aa8d breaks vhost_net
because it always registers the virtio_pci_host_notifier_read() handler
function on the ioeventfd, even when vhost_net.ko is using the ioeventfd.
The result is both QEMU and vhost_net.ko polling on the same eventfd
and the virtio_net.ko guest driver seeing inconsistent results:
# ifconfig eth0 192.168.0.1 netmask 255.255.255.0
virtio_net virtio0: output:id 0 is not a head!
To fix this, proceed the same as we do for irqfd: add a parameter to
virtio_queue_set_host_notifier_fd_handler and in that case only set
the notifier, not the handler.
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Tested-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* bonzini/scsi-next:
scsi: add support for ATA_PASSTHROUGH_xx scsi command
esp: add missing const on TypeInfo structures
esp: enable for all PCI machines
Revert "megasas: disable due to build breakage"
megasas: static SAS addresses
scsi-disk: fix compilation with DEBUG_SCSI
megasas: Update function megasys_scsi_uninit
SCSI: STARTSTOPUNIT only eject/load media if powercondition is 0
SCSI: Update the sense code for PREVENT REMOVAL errors
Correct the command names of opcode 0x85 and 0xa1, and calculate
their xfer size from CDB.
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* stefanha/net:
net: add the support for -netdev socket, listen
net: fix the coding style
hub: add the support for hub own flow control
net: determine if packets can be sent before net queue deliver packets
net: cleanup deliver/deliver_iov func pointers
net: Make "info network" output more readable info
net: Rename qemu_del_vlan_client() to qemu_del_net_client()
net: Rename vc local variables to nc
net: Rename VLANClientState to NetClientState
net: Rename non_vlan_clients to net_clients
net: Remove VLANState
net: Remove vlan code from net.c
net: Convert qdev_prop_vlan to peer with hub
net: Drop vlan argument to qemu_new_net_client()
hub: Check that hubs are configured correctly
net: Look up 'vlan' net clients using hubs
net: Use hubs for the vlan feature
net: Add a hub net client
net: Add interface to bridge when SIOCBRADDIF isn't available
This patch introduces a new property 'sas_address' which
allows the user to specify the SAS address for the HBA.
The default address is following the NAA locally assigned
identifier format with the locally assigned address
0x525400 as used eg for the MAC addresses.
The lower bytes are set to the pci address which
will ensure uniqueness for the local machine.
The port addresses are now calculated based on the magic
number 0x1221 (which is found in real hardware, too) plus
the device number.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit f90c2bcdbc changed
PCIUnregisterFunc, therefore the function prototype
needs an update.
megasas.o is currently not linked, so this bug was not
detected by the buildbots.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The START STOP UNIT command will only eject/load media if
power condition is zero.
If power condition is !0 then LOEJ and START will be ignored.
From MMC (sbc contains similar wordings too)
The Power Conditions field requests the block device to be placed
in the power condition defined in
Table 558. If this field has a value other than 0h then the Start
and LoEj bits shall be ignored.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change the sense codes for failures to eject a device that is locked
by PREVENT_ALLOW_MEDIUM_REMOVAL from
the generic MEDIA_LOAD_OR_EJECT_FAILED to the more specific
MEDIUM_REMOVAL_PREVENTED.
The second sense code is more accurate, and is also listed in MMC annex F
for the recommended sense codes for MMC devices while the first sense code is not.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For command line options which permit '?' meaning 'please list the
permitted values', add support for 'help' as a synonym, by abstracting
the check out into a helper function.
This change means that in some cases where we were being lazy in
our string parsing, "?junk" will now be rejected as an invalid option
rather than being (undocumentedly) treated the same way as "?".
Update the documentation to use 'help' rather than '?', since '?'
is a shell metacharacter and thus prone to fail confusingly if there
is a single character filename in the current working directory and
the '?' has not been escaped. It's therefore better to steer users
towards 'help', though '?' is retained for backwards compatibility.
We do not, however, update the output of the system emulator's -help
(or any documentation autogenerated from the qemu-options.hx which
is the source of the -help text) because libvirt parses our -help
output and will break. At a later date when QEMU provides a better
interface so libvirt can avoid having to do this, we can update the
-help text too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Moving reset callback into cpu object from board level and
resetting cpu at the end of x86_cpu_realize() will allow properly
create cpu object during run-time (hotplug) without calling reset externaly.
When reset over QOM hierarchy is implemented, reset callback
should be removed.
v2:
- leave cpu_reset in pc_new_cpu() for now, it's to be cleaned up when APIC
init is moved in cpu.c
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
MP initialization protocol differs between cpu families, and for P6 and
onward models it is up to CPU to decide if it will be BSP using this
protocol, so try to model this. However there is no point in implementing
MP initialization protocol in qemu. Thus first CPU is always marked as BSP.
This patch:
- moves decision to designate BSP from board into cpu, making cpu
self-sufficient in this regard. Later it will allow to cleanup hw/pc.c
and remove cpu_reset and wrappers from there.
- stores flag that CPU is BSP in IA32_APIC_BASE to model behavior
described in Inted SDM vol 3a part 1 chapter 8.4.1
- uses MSR_IA32_APICBASE_BSP flag in apic_base for checking if cpu is BSP
patch is based on Jan Kiszka's proposal:
http://thread.gmane.org/gmane.comp.emulators.qemu/100806
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
xen_pt_unregister_device is used as PCIUnregisterFunc, so it should
match the type.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Another step in moving the vlan feature out of net core. Users only
deal with NetClientState and therefore qemu_del_vlan_client() should be
named qemu_del_net_client().
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Now that VLANClientState has been renamed to NetClientState all 'vc'
local variables should be 'nc'. Much of the code already used 'nc' but
there are places where 'vc' needs to be renamed.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The vlan feature is no longer part of net core. Rename VLANClientState
to NetClientState because net clients are not explicitly associated with
a vlan at all, instead they have a peer net client to which they are
connected.
This patch is a mechanical search-and-replace except for a few
whitespace fixups where changing VLANClientState to NetClientState
misaligned whitespace.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
VLANState is no longer used and can be removed.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The vlan implementation in net.c has been replaced by hubs so we can
remove the code.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Instead of using VLANState use net/hub.h to support the vlan qdev
property. The vlan qdev property becomes an alias for the peer qdev
property but is represented as a VLAN ID number. When a VLAN ID is
selected the device will really peer with a hub port.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
For 9p we can get the attach request multiple times for the
same export. So don't adding migration blocker for every
attach request.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
* bonzini/scsi-next: (32 commits)
virtio-scsi: enable MSI-X support
virtio-scsi: add ioeventfd support
virtio-scsi: report parameter change events
virtio-scsi: do not report dropped events after reset
virtio-scsi: Report missed events
virtio-scsi: Implement hotplug support for virtio-scsi
scsi: report parameter changes to HBA drivers
scsi-disk: report resized disk via sense codes
scsi: establish precedence levels for unit attention
scsi: introduce hotplug() and hot_unplug() interfaces for SCSI bus
scsi: add tracepoint for scsi_req_cancel
scsi-disk: removable hard disks support load/eject
scsi-disk: Fail medium writes with proper sense for readonly LUNs
scsi-disk: improve the lba-out-of-range tests for read/write/verify
scsi-disk: rd/wr/vr-protect !=0 is an error
scsi-disk: support toggling the write cache
scsi-disk: parse MODE SELECT commands and parameters
scsi-disk: fix changeable values for MODE_PAGE_R_W_ERROR
scsi-disk: adjust offsets in MODE SENSE by 2
scsi-disk: support emulated TO_DEV requests
...
Drop a duplicate definition of the 'disabled' property from
the escc qdev property list: this redefinition is currently
effectively ignored but will become an error. (The duplication
was inadvertently introduced in 2009 in commit ec02f7dec2.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Andreas Frber <afaerber@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
While virtio-scsi does support multiqueue, the default number of
interrupt vectors is not enough to actually enable usage of
multiple queues in the driver; this is because with only 2
vectors the driver will not be able to use a separate
interrupt for each request queue. Derive the desired number
of vectors from the number of request queues.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Probably due to bad merge months ago, virtio-scsi-pci did not have
ioeventfd support. Fix this and enable it by default, as is the
case for other virtio-pci devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When an event is reported but no buffers are present in the event vq,
we can set a flag and report a dummy event as soon as one is added.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the hotplug() and hot_unplug() interfaces in virtio-scsi, by signal
the virtio_scsi.ko in guest kernel via event virtual queue.
The counterpart patch of virtio_scsi.ko will be sent soon in another thread.
Signed-off-by: Sen Wang <senwang@linux.vnet.ibm.com>
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
[ Add memset, fix LUN field, placate checkpatch - Paolo ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linux will not use these, but a very similar mechanism will be used to
report the condition via virtio-scsi events.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a device is resized, we will report a unit attention condition
for CAPACITY DATA HAS CHANGED. However, we should ensure that this
condition does not override a more important unit attention condition.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add two interfaces hotplug() and hot_unplug() to scsi bus info.
The scsi bus can implement these two interfaces to signal the HBA driver
of guest kernel to add/remove the scsi device in question.
Signed-off-by: Sen Wang <senwang@linux.vnet.ibm.com>
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
[ Fixed braces and indentation - Paolo ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Support for the LOEJ bit of the START/STOP UNIT command right now is
limited to CD-ROMs. This is wrong, since removable hard disks (in the
real world: SD card readers) also support it in pretty much the same way.
Without the LOEJ bit, START/STOP UNIT does nothing for all devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add sense code for DATA_PROTECT/WRITE_PROTECTED and return this error
for any WRITE*/WRITE_VERIFY* calls if the device is readonly=on,
i.e. write-protected
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Improve the tests for the LBA to cover more cases.
For the 16 byte opcodes, the lba is a uint64, so we need to check is to
make sure that we do not wrap. For example if an opcode would specify
the LBA:0xffffffffffffffff and LEN:2 then lba+len would wrap to 1.
Also verify that ALL requested blocks are available, not just the first one.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The QEMU SCSI emulation does not support protection information,
so any READ/WRITE/VERIFY commands that has the protect bits set to
non-zero should fail with ILLEGAL_REQUEST/INVALID_FIELD_IN_CDB
From SCSI SBC :
If the logical unit does not support protection information,
then the device server should terminate the command with CHECK CONDITION
status with the sense key set to ILLEGAL REQUEST and the additional sense
code set to INVALID FIELD IN CDB.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
[ Rebase after scsi_dma_reqops introduction - Paolo ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Finally, this uses the "plumbing" in the previous patch to
add support for toggling the WCE bit of the caching mode page.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds the bulk of the parsing code for MODE SELECT, including
breaking out changes to different mode pages, and checking that only
changeable values are modified.
In order to report errors correctly two passes are made through the
parameters; the first only looks for errors, the second actually
applies the changes to the mode page.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make offsets the same when implementing MODE SELECT. This is
because MODE SELECT has to deal with both 2-byte and 4-byte headers.
Unfortunately, this means that the offsets are now off by two compared
to the descriptions in the SCSI specs, which include the header.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds the implementation of write_data for the emulated
command case. The first time through it asks for more data,
the second time it finishes the processing of the command.
MODE SELECT and MODE SELECT(10) can now be re-enabled, but they
will not do much.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous patch only separated the send_command callback.
Use different implementations also for read_data and write_data.
The latter is still unreachable, so it aborts for now.
read_data passes the data buffer that was prepared and completes
the command.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only checks for present medium were still done in scsi_send_command
for emulated commands. So move those to scsi_disk_emulate_command
and return different SCSIReqOps depending on the kind of command.
Checks for present medium can be done unconditionally for the
scsi_disk_dma_reqops case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We want to use separate SCSIReqOps for emulated commands needing an
allocated buffer vs. those that are zerocopy when the HBA supports
S/G lists. Ensure that all of the former are in scsi_disk_emulate_command.
Commands that do not have any parameters are more similar to emulated
commands, so also move them, even if they do I/O.
Finally, MODE SELECT and MODE SELECT(10) are broken because we do not
yet support passing parameter data _to_ emulated commands, so disable
them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By making discard asynchronous, we can reuse all the error handling
code that is used for other commands.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds two new properties vendor and product to SCSI disks.
These options let the user customize the inquiry data returned by the
disk.
Signed-off-by: Yan Vugenfirer <yan@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
[ Use vendor and product property names, avoid "if" statements. - PB ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
scsi-block is a passthrough device and does not allow customization
of vendor, product, removable, DPOFUA, block size or any other piece of
information. Thus, drop DEFINE_SCSI_DISK_PROPERTIES() from the
list of qdev properties.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simplify the code by checking against req->hba_private directly,
and asserting that it is non-NULL before a command is completed
or canceled.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By first resetting the devices, lsi_soft_reset will find the queue
already cleared so there is no need to do that forcibly (which may also
leak SCSIRequests, and/or worse due to dangling references to the
lsi_request in the hba_private field).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
scsi_req_abort is for terminating a command with a non-zero status.
The ABORT task management function is invoked by scsi_req_cancel.
In fact, ABORTED_COMMAND is a sense key, not a SAM status code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
trace_megasas_dcmd_dump_frame() takes 9 arguments, which is
rather much. Plus the trace infrastructure doesn't support
it. As we can get the information via other means it's pointless
to have it in the driver, so rather use some proper trace
point here and remove the old one.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* stefanha/net:
remove unused QemuOpts parameter from net init functions
convert net_init_bridge() to NetClientOptions
convert net_init_tap() to NetClientOptions
convert net_init_vde() to NetClientOptions
convert net_init_socket() to NetClientOptions
convert net_init_slirp() to NetClientOptions
convert net_init_dump() to NetClientOptions
convert net_init_nic() to NetClientOptions
convert net_client_init() to OptsVisitor
hw, net: "net_client_type" -> "NetClientOptionsKind" (qapi-generated)
qapi schema: add Netdev types
qapi schema: remove trailing whitespace
qapi: introduce OptsVisitor
expose QemuOpt and QemuOpts struct definitions to interested parties
qapi: introduce "size" type
qapi: generate C types for fixed-width integers
qapi: add test case for deallocating traversal of incomplete structure
qapi: fix error propagation
MAINTAINERS: Replace net maintainer Mark McLoughlin with Stefan Hajnoczi
* stefanha/trivial-patches:
Fix some more Qemus in documentation and help text
qdev: Fix Open Firmware comment
cpus.c: Make all_cpu_threads_idle() static
Use macro QEMU_PACKED for new packed structures
Recognize PCID feature
powerpc pci: fixed packing of ranges[]
Commit 0d936928ef removed code,
but left the related comment at a location where it no longer
belongs to.
The patch moves the comment to the correct callback and improves the text.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Since commit 541dc0d47f,
some new packed structures were added without using QEMU_PACKED.
QEMU_PACKED is needed for compilations with MinGW.
For other platforms nothing changes.
The code was fixed using this command:
git grep -la '__attribute__ ((packed))'|xargs perl -pi -e 's/__attribute__ \(\(packed\)\)/QEMU_PACKED/'
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
By default mingw-gcc is trying to pack structures the way to
preserve binary compatibility with MS Visual C what leads to
incorrect and unexpected padding in the PCI bus ranges property of
the sPAPR PHB.
The patch replaces __attribute__((packed)) with more strict QEMU_PACKED
which actually is __attribute__((gcc_struct, packed)) on Windows.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Now that we have LPAE support and can handle passing 64 bit
RAM sizes to Linux via the device tree, we can lift the
restriction in the Versatile Express A15 daughterboard model
on not having more than 2GB of RAM. Allow up to 30GB, which
is the maximum that can fit in the address map before running
into the (unmodelled) aliases of the first 2GB.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support the case where the device tree blob specifies that
#address-cells and #size-cells are greater than 1. (This
is needed for device trees which can handle 64 bit physical
addresses and thus total RAM sizes over 4GB.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
The legacy ATAGS format for passing information to the kernel only
allows RAM sizes which fit in 32 bits; enforce this restriction
rather than silently doing something weird.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Clean up the mix of getting the RAM size from the global ram_size
and from the ram_size field in the arm_boot_info structure, so
that we always use the structure field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Make the RAM size in arm_boot_info a uint64_t so it can express
the larger RAM sizes that may be seen in LPAE systems.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Add a missing guard that meant we would segfault if the guest read
UARTDR on a PL011 serial device which had no chr backend connected.
(This didn't happen for Linux guests because Linux reads the flags
register and doesn't try to read the UART if it's empty.)
Reported-by: Christian Müller <christian.mueller@heig-vd.ch>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added (msi|msix)_set_message() function for whoever might
want to use them.
Currently msi_notify()/msix_notify() write to these vectors to
signal the guest about an interrupt so the correct values have to
written there by the guest or QEMU.
For example, POWER guest never initializes MSI/MSIX vectors, instead
it uses RTAS hypercalls. So in order to support MSIX for virtio-pci on
POWER we have to initialize MSI/MSIX message from QEMU.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This per-device notifier shall be triggered by any interrupt router
along the path of a device's legacy interrupt signal on routing changes.
For simplicity reasons and as this is a slow path anyway, no further
details on the routing changes are provided. Instead, the callback is
expected to use pci_device_route_intx_to_irq to check the effect of the
change.
Will be used by KVM PCI device assignment and VFIO.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Device assigned on KVM needs to know the mode
(enabled/inverted/disabled) and the IRQ number that a given device
triggers in the attached interrupt controller.
Add a PCI IRQ path discovery function that walks from a given device to
the host bridge, and gets this information. For
this purpose, a host bridge callback function is introduced:
route_intx_to_irq. It is so far only implemented by the PIIX3, other
host bridges can be added later on as required.
Will be used for KVM PCI device assignment and VFIO.
Based on patch by Jan Kiszka, with minor tweaks.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* kwolf/for-anthony: (41 commits)
fdc-test: Clean up a bit
fdc-test: introduce test_relative_seek
fdc: fix relative seek
qemu-iotests: Valgrind support
coroutine-ucontext: Help valgrind understand coroutines
qemu-io: Fix memory leaks
hw/block-common: Factor out fall back to legacy -drive cyls=...
blockdev: Don't limit DriveInfo serial to 20 characters
hw/block-common: Factor out fall back to legacy -drive serial=...
hw/block-common: Move BlockConf & friends from block.h
Relax IDE CHS limits from 16383,16,63 to 65535,16,255
blockdev: Drop redundant CHS validation for if=ide
hd-geometry: Compute BIOS CHS translation in one place
qtest: Test we don't put hard disk info into CMOS for a CD-ROM
ide pc: Put hard disk info into CMOS only for hard disks
block: Geometry and translation hints are now useless, purge them
qtest: Cover qdev property for BIOS CHS translation
ide: qdev property for BIOS CHS translation
qdev: New property type chs-translation
qdev: Collect private helpers in one place
...
* qemu-kvm/uq/master:
virtio: move common irqfd handling out of virtio-pci
virtio: move common ioeventfd handling out of virtio-pci
event_notifier: add event_notifier_set_handler
memory: pass EventNotifier, not eventfd
ivshmem: wrap ivshmem_del_eventfd loops with transaction
ivshmem: use EventNotifier and memory API
event_notifier: add event_notifier_init_fd
event_notifier: remove event_notifier_test
event_notifier: add event_notifier_set
apic: Defer interrupt updates to VCPU thread
apic: Reevaluate pending interrupts on LVT_LINT0 changes
apic: Resolve potential endless loop around apic_update_irq
kvm: expose tsc deadline timer feature to guest
kvm_pv_eoi: add flag support
kvm: Don't abort on kvm_irqchip_add_msi_route()
qdev_prop_set_string uses object_property_set_str, which takes
a const char * for the value. Lets propagate the constness
into qdev_prop_set_string.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All current users (IDE, SCSI and virtio-blk) happen to share this 20
characters limit. Still, it should be left to device models. They
already enforce their limits. They have to, as the DriveInfo limit
only affects legacy -drive serial=..., not the qdev properties.
usb-storage, which doesn't limit serial number length, also uses
DriveInfo for -usbdevice. But that doesn't provide access to
DriveInfo serial.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This stuff doesn't belong to block layer, and was put there only
because a better home didn't exist then. Now it does.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
New limits straight from ATA4 6.2 Register delivered data transfer
command sector addressing.
I figure the old sector limit 63 was blindly copied from the BIOS
int 13 limit. Doesn't apply to the hardware. No idea where the old
cylinder limit comes from.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently, it is split between hd_geometry_guess() and
pc_cmos_init_late(). Confusing. info qtree shows the result of the
former. Also confusing.
Fold the part done in pc_cmos_init_late() into hd_geometry_guess().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In particular, don't set disk type and geometry when a CD-ROM on bus
ide.0 has media during CMOS initialization.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are two producers of these hints: drive_init() on behalf of
-drive, and hd_geometry_guess().
The only consumer of the hint is hd_geometry_guess().
The callers of hd_geometry_guess() call it only when drive_init()
didn't set the hints. Therefore, drive_init()'s hints are never used.
Thus, hd_geometry_guess() only ever sees hints it produced itself in a
prior call. Only the first call computes something, subsequent calls
just repeat the first call's results. However, hd_geometry_guess() is
never called more than once: the device models don't, and the block
device is destroyed on unplug. Thus, dropping the repeat feature
doesn't break anything now.
If a block device wasn't destroyed on unplug and could be reused with
a new device, then repeating old results would be wrong. Thus,
dropping the repeat feature prevents future breakage.
This renders the hints unused. Purge them from the block layer.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This isn't quite orthodox. CHS translation is firmware configuration,
communicated via the RTC's CMOS RAM, not a property of the disk. But
it's best to treat it just like geometry anyway.
Maintain backward compatibility exactly like for geometry: fall back
to DriveInfo's translation, set with -drive trans=...
Bonus: info qtree now shows the translation. Except when it shows
"auto": that's resolved by pc_cmos_init_late(). To be addressed
shortly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Just code motion, with one long line wrapped to keep checkpatch.pl
happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Geometry needs to be qdev properties, because it belongs to the
disk's guest part.
Maintain backward compatibility exactly like for serial: fall back to
DriveInfo's geometry, set with -drive cyls=...
Do this only for ide-hd. ide-drive is legacy. ide-cd doesn't have a
geometry.
Bonus: info qtree now shows the geometry.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Geometry needs to be qdev properties, because it belongs to the
disk's guest part.
Maintain backward compatibility exactly like for serial: fall back to
DriveInfo's geometry, set with -drive cyls=...
Bonus: info qtree now shows the geometry.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Geometry needs to be qdev properties, because it belongs to the
disk's guest part.
Maintain backward compatibility exactly like for serial: fall back to
DriveInfo's geometry, set with -drive cyls=...
Do this only for scsi-hd. scsi-disk is legacy. scsi-cd doesn't have
a geometry. scsi-block should get geometry from the host disk.
Bonus: info qtree now shows the geometry.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Best to use the same type, to avoid unwanted truncation or sign
extension.
BlockConf can't use plain int for cyls, heads and secs, because
integer properties require an exact width.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PC BIOS setup needs IDE geometry information. Get it directly from
the device model rather than through the block layer. In preparation
of purging geometry from the block layer, which will happen later in
this series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
hd_geometry_guess() picks geometry and translation. Callers can get
the geometry directly, via parameters, but for translation they need
to go through the block layer.
Add a parameter for translation, so it can optionally be gotten just
like geometry. In preparation of purging translation from the block
layer, which will happen later in this series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When hd_geometry_guess() picks a geometry, it also picks the
appropriate translation, but only when the prior translation hint is
BIOS_ATA_TRANSLATION_AUTO. Looks wrong, because such a prior
translation would be passed to the BIOS whether it's suitable for the
geometry or not.
Fortunately, that can't happen. There are just two ways for the
translation hint to get set to something other than
BIOS_ATA_TRANSLATION_AUTO: drive_init() on behalf of -drive trans=...,
and hd_geometry_guess(). Both set it only when they also set a valid
geometry hint, i.e. one with a non-zero number of cylinders.
Since hd_geometry_guess() returns right away when it finds a valid
geometry hint, translation can only be BIOS_ATA_TRANSLATION_AUTO in
the remainder of the function.
Assert this, and simplify accordingly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit f3d54fc4 factored it out of hw/ide.c for reuse. Sensible,
except it was put into block.c. Device-specific functionality should
be kept in device code, not the block layer. Move it to
hw/hd-geometry.c, and make stylistic changes required to keep
checkpatch.pl happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 5bbdbb46 moved it to block.c because "other geometry guessing
functions already reside in block.c". Device-specific functionality
should be kept in device code, not the block layer. Move it back.
Disk geometry guessing is still in block.c. To be moved out in a
later patch series.
Bonus: the floppy type used in pc_cmos_init() now obviously matches
the one in the FDrive. Before, we relied on
bdrv_get_floppy_geometry_hint() picking the same type both in
fd_revalidate() and in pc_cmos_init().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Let the text cursor blink at 1.875 Hz, the original VGA cursor
frequency. No timer is used, instead we rely on the fact that the
display is updated periodically.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Switch a format string from %x to TARGET_PRIxPHYS so that it will
continue to work even if target_phys_addr_t is changed
to 64 bits in the future.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use the new TARGET_PRIxPHYS macro to avoid the need to define an
OMAP_FMT_plx macro whose expansion depends directly on
TARGET_PHYS_ADDR_BITS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The PCI version is supported in lots of Operating Systems,
and has been successfully tested on:
- MS DOS 6.22 (using DC390 driver)
- MS Windows 3.11 (using DC390 driver)
- MS Windows 98 SE (using default driver)
- MS Windows NT 3.1 (using DC390 driver)
- MS Windows NT 4.0 (using default driver)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The same mechanism is already in place for some select commands.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Suggested by blue swirl. Patch is on top of Paolo's
scsi-next tree.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Move down the expire time calculation down in the frame timer, to the
point where the timer is actually reloaded. This way we'll notice any
async_stepdown changes (especially resetting to 0 due to usb activity).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
With the async schedule being kicked from other places than the frame
timer (commit 0f588df8b3) it may happen
that we call ehci_commit_interrupt() more than once per frame.
Move the call from the async schedule handler to the frame timer to
restore old irq behavior, which is more correct. Fixes regressions
with some linux kernel versions.
TODO: implement full Interrupt Threshold Control support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
$subject says all: when loading old (v1) vmstate which doesn't contain
expire_time initialize it with a reasonable default (current time).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
$subject says all. First cut.
It's a pure UAS (usb attached scsi) emulation, without BOT (bulk-only
transport) compatibility. If your guest can't handle it use usb-storage
instead.
The emulation works like any other scsi hba emulation (eps, lsi, virtio,
megasas, ...). It provides just the HBA where you can attach scsi
devices as you like using '-device'. A single scsi target with up to
256 luns is supported.
For now only usb 2.0 transport is supported. This will change in the
future though as I plan to use this as playground when codeing up &
testing usb 3.0 transport and streams support in the qemu usb core and
the xhci emulation.
No migration support yet. I'm planning to add usb 3.0 support first as
this probably requires saving additional state.
Special thanks go to Paolo for bringing the qemu scsi emulation into
shape, so this can be added nicely without having to touch a single line
of scsi code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
All transports can use the same event handler for the irqfd, though the
exact mechanics of the assignment will be specific. Note that there
are three states: handled by the kernel, handled in userspace, disabled.
This also lets virtio use event_notifier_set_handler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
All transports can use the same event handler for the ioeventfd, though
the exact setup (address/memory region) will be specific.
This lets virtio use event_notifier_set_handler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Under Win32, EventNotifiers will not have event_notifier_get_fd, so we
cannot call it in common code such as hw/virtio-pci.c. Pass a pointer to
the notifier, and only retrieve the file descriptor in kvm-specific code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
All of ivshmem's usage of eventfd now has a corresponding API in
EventNotifier. Simplify the code by using it, and also use the
memory API consistently to set up and tear down the ioeventfds.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add a missing cast to avoid gcc complaining about format string
errors when printing an expression based on a target_phys_addr_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Chubb <peter.chubb@nicta.com.au>
Most device models have a simple lifecycle for the hba_private field
and they can free it when a request is completed or cancelled.
However, in some cases it may be simpler to tie the lifetime
of hba_private to that of the included SCSIRequest. This patch
adds a free_request callback to SCSIBusInfo that lets an HBA
device model do exactly that.
Normally, device models use req->hba_private == NULL to flag requests
that have been completed already. Device models that use free_request
will still need to track this using a flag. This is the reason why
"converting" existing HBAs to use free_request adds complexity and
makes little sense. It is simply an additional convenience that is
provided by the SCSI layer. USB-attached storage will be the first
user.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
KVM performs TPR raising asynchronously to QEMU, specifically outside
QEMU's global lock. When an interrupt is injected into the APIC and TPR
is checked to decide if this can be delivered, a stale TPR value may be
used, causing spurious interrupts in the end.
Fix this by deferring apic_update_irq to the context of the target VCPU.
We introduce a new interrupt flag for this, CPU_INTERRUPT_POLL. When it
is set, the VCPU calls apic_poll_irq before checking for further pending
interrupts. To avoid special-casing KVM, we also implement this logic
for TCG mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When the guest modifies the LVT_LINT0 register, we need to check if some
pending PIC interrupt can now be delivered.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit d96e173769 refactored the reinjection of pending PIC interrupts.
However, it missed the potential loop of apic_update_irq ->
apic_deliver_pic_intr -> apic_local_deliver -> apic_set_irq ->
apic_update_irq that /could/ occur if LINT0 is injected as APIC_DM_FIXED
and that vector is currently blocked via TPR.
Resolve this by reinjecting only where it matters: inside
apic_get_interrupt. This function may clear a vector while a
PIC-originated reason still exists.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* mjt/mjt-iov2:
rewrite iov_send_recv() and move it to iov.c
cleanup qemu_co_sendv(), qemu_co_recvv() and friends
export iov_send_recv() and use it in iov_send() and iov_recv()
rename qemu_sendv to iov_send, change proto and move declarations to iov.h
change qemu_iovec_to_buf() to match other to,from_buf functions
consolidate qemu_iovec_copy() and qemu_iovec_concat() and make them consistent
allow qemu_iovec_from_buffer() to specify offset from which to start copying
consolidate qemu_iovec_memset{,_skip}() into single function and use existing iov_memset()
rewrite iov_* functions
change iov_* function prototypes to be more appropriate
virtio-serial-bus: use correct lengths in control_out() message
Conflicts:
tests/Makefile
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kwolf/for-anthony: (24 commits)
block: Factor bdrv_read_unthrottled() out of guess_disk_lchs()
qtest: Tidy up temporary files properly
fdc: Drop broken code for user-defined floppy geometry
fdc_test: introduce test_sense_interrupt
fdc_test: update media_change test
fdc: fix interrupt handling
fdc: rewrite seek and DSKCHG bit handling
block: introduce bdrv_swap, implement bdrv_append on top of it
block: copy over job and dirty bitmap fields in bdrv_append
raw: hook into blkdebug
blkdebug: optionally tie errors to a specific sector
blkdebug: store list of active rules
blkdebug: pass getlength to underlying file
blkdebug: tiny cleanup
blkdebug: remove sync i/o events
sheepdog: traverse pending_list from the first for each time
sheepdog: split outstanding list into inflight and pending
sheepdog: make sure we don't free aiocb before sending all requests
sheepdog: use coroutine based socket functions in coroutine context
sheepdog: restart I/O when socket becomes ready in do_co_req()
...
* kraxel/usb.55:
usb-host: add trace events for iso xfers
usb: fix interface initialization
usb: split endpoint init and reset
usb-redir: Correctly handle the usb_redir_babble usbredir status
ehci: Kick async schedule on wakeup in the non companion case
usb-ehci: Fix an assert whenever isoc transfers are used
ehci: don't flush cache on doorbell rings.
ehci: fix td writeback
ehci: fix ehci_qh_do_overlay
* bonzini/scsi-next:
scsi: Fix transfer length for READ POSITION commands.
scsi: Add basic support for SCSI media changer commands.
scsi: Ensure command and transfer lengths are set for all SCSI devices
scsi: Fix LOAD_UNLOAD
scsi: Fix data length == SCSI_SENSE_BUF_SIZE
virtio-scsi: do not crash on adding buffers to the event queue
megasas: LSI Megaraid SAS HBA emulation
megasas: Add header file
ISCSI: force use of sg for SMC and SSC devices
ISCSI: Add SCSI passthrough via scsi-generic to libiscsi
scsi-disk: implement READ DISC INFORMATION
atapi: implement READ DISC INFORMATION
scsi: add a qdev property for the disk's WWN
scsi: simplify handling of the VPD page length field
bdrv_get_floppy_geometry_hint() fails to store through its parameter
drive when bs has a geometry hint. Makes fd_revalidate() assign
random crap to drv->drive.
Has been broken that way for ages. Harmless, because:
* The only way to set a geometry hint is -drive if=none,cyls=...
Since commit c219331e, probably unintentional.
* The only use of drv->drive is as argument to another
bdrv_get_floppy_geometry_hint(). Which doesn't use it, since the
geometry hint is still there.
Drop the broken code, ignore -drive parameter cyls, heads and secs for
floppies even with if=none, just like before commit c219331e. Matches
-help, which explains cyls, heads, secs as "hard disk physical
geometry".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If you call the SENSE INTERRUPT STATUS command while there is no interrupt
waiting you get as result unknown command.
Fixed status0 register handling for read/write/format commands.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This bit is cleared on every successful seek to a different track (cylinder).
The seek is also called on revalidate or on read/write/format commands which
also clear the DSKCHG bit.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace iso transfer fprintf's with trace points. Also rename existing
tracepoints so they all match usb_host_iso_*.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create a new usb_ep_reset() function to reset endpoint state, without
re-initialiting the queues, so we don't unlink in-flight packets just
because usb-host has to re-parse the descriptor tables.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 0f588df8b3, added code
to ehci_wakeup to kick the async schedule on wakeup, but the else
was positioned wrong making it trigger for devices which are routed
to the companion rather then to the ehci controller itself.
This patch fixes this. Note that the "programming style" with using the
return at the end of the companion block matches how the companion case
is handled in the other ports ops, and is done this way for consistency.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
hcd-ehci.c is missing an usb_packet_init() call for the ipacket UsbPacket
it uses for isoc transfers, triggering an assert (taking the entire vm down)
in usb_packet_setup as soon as any isoc transfers are done by a high speed
USB device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 4be23939ab makes ehci instantly
zap any unlinked queue heads when the guest rings the doorbell.
While hacking up uas support this turned out to be a problem. The linux
kernel can unlink and instantly relink the very same queue head, thereby
killing any async packets in flight. That alone isn't an issue yet, the
packet will canceled and resubmitted and everything is fine. We'll run
into trouble though in case the async packet is completed already, so we
can't cancel it any more. The transaction is simply lost then.
usb_ehci_qh_ptrs q (nil) - QH @ 39c4f000: next 39c4f122 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_qh_ptrs q 0x7f95feba90a0 - QH @ 39c4f000: next 39c4f122 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_qh_ptrs q 0x7f95fe515210 - QH @ 39c4f120: next 39c4f0c2 qtds 29dbce40,29dbc4e0,00000009
usb_ehci_qh_fields QH @ 39c4f120 - rl 4, mplen 512, eps 2, ep 1, dev 2
usb_ehci_packet_action q 0x7f95fe515210 p 0x7f95fdec32a0: alloc
usb_packet_state_change bus 0, port 2, ep 1, packet 0x7f95fdec32e0, state undef -> setup
usb_ehci_packet_action q 0x7f95fe515210 p 0x7f95fdec32a0: process
usb_uas_command dev 2, tag 0x2, lun 0, lun64 00000000-00000000
scsi_req_parsed target 0 lun 0 tag 2 command 42 dir 2 length 16384
scsi_req_parsed_lba target 0 lun 0 tag 2 command 42 lba 5933312
scsi_req_alloc target 0 lun 0 tag 2
scsi_req_continue target 0 lun 0 tag 2
scsi_req_data target 0 lun 0 tag 2 len 16384
usb_uas_scsi_data dev 2, tag 0x2, bytes 16384
usb_uas_write_ready dev 2, tag 0x2
usb_packet_state_change bus 0, port 2, ep 1, packet 0x7f95fdec32e0, state setup -> complete
usb_ehci_packet_action q 0x7f95fe515210 p 0x7f95fdec32a0: free
usb_ehci_qh_ptrs q 0x7f95fdec3210 - QH @ 39c4f0c0: next 39c4f002 qtds 29dbce40,00000001,00000009
usb_ehci_qh_fields QH @ 39c4f0c0 - rl 4, mplen 512, eps 2, ep 2, dev 2
usb_ehci_queue_action q 0x7f95fe5152a0: free
usb_packet_state_change bus 0, port 2, ep 2, packet 0x7f95feba9170, state async -> complete
^^^ async packets completes.
usb_ehci_packet_action q 0x7f95fdec3210 p 0x7f95feba9130: wakeup
usb_ehci_qh_ptrs q (nil) - QH @ 39c4f000: next 39c4f122 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_qh_ptrs q 0x7f95feba90a0 - QH @ 39c4f000: next 39c4f122 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_qh_ptrs q 0x7f95fe515210 - QH @ 39c4f120: next 39c4f002 qtds 29dbc4e0,29dbc8a0,00000009
usb_ehci_qh_fields QH @ 39c4f120 - rl 4, mplen 512, eps 2, ep 1, dev 2
usb_ehci_queue_action q 0x7f95fdec3210: free
usb_ehci_packet_action q 0x7f95fdec3210 p 0x7f95feba9130: free
^^^ endpoint #2 queue head removed from schedule, doorbell makes ehci zap the queue,
the (completed) usb packet is freed too and gets lost.
usb_ehci_qh_ptrs q (nil) - QH @ 39c4f000: next 39c4f0c2 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_qh_ptrs q 0x7f95feba90a0 - QH @ 39c4f000: next 39c4f0c2 qtds 00000000,00000001,39c50000
usb_ehci_qh_fields QH @ 39c4f000 - rl 0, mplen 0, eps 0, ep 0, dev 0
usb_ehci_queue_action q 0x7f9600dff570: alloc
usb_ehci_qh_ptrs q 0x7f9600dff570 - QH @ 39c4f0c0: next 39c4f122 qtds 29dbce40,00000001,00000009
usb_ehci_qh_fields QH @ 39c4f0c0 - rl 4, mplen 512, eps 2, ep 2, dev 2
usb_ehci_packet_action q 0x7f9600dff570 p 0x7f95feba9130: alloc
usb_packet_state_change bus 0, port 2, ep 2, packet 0x7f95feba9170, state undef -> setup
usb_ehci_packet_action q 0x7f9600dff570 p 0x7f95feba9130: process
usb_packet_state_change bus 0, port 2, ep 2, packet 0x7f95feba9170, state setup -> async
usb_ehci_packet_action q 0x7f9600dff570 p 0x7f95feba9130: async
^^^ linux kernel relinked the queue head, ehci creates a new usb packet,
but we should have delivered the completed one instead.
usb_ehci_qh_ptrs q 0x7f95fe515210 - QH @ 39c4f120: next 39c4f002 qtds 29dbc4e0,29dbc8a0,00000009
usb_ehci_qh_fields QH @ 39c4f120 - rl 4, mplen 512, eps 2, ep 1, dev 2
So instead of instantly zapping the queue we'll set a flag that the
queue needs revalidation in case we'll see it again in the schedule.
ehci then checks that the queue head fields addressing / describing the
endpoint and the qtd pointer match the cached content before reusing it.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Only write back the dwords the hc is supposed to update. Should not
make a difference in theory as the guest must not touch the td while
it is active to avoid races. But it is still more correct.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
BARs are registered in init functions from memory regions created
by the drivers. Exit functions destroy those memory regions.
By unregistering the io regions after exit(), we're calling
memory_region_del_subregion on freed memory. Don't do that. The
option rom comes along for the ride because it's more symmetric
to how it's created.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Not a single driver has any possibility of failure on their
exit function, let's keep it that way.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make the state fields rx_desc_addr and tx_desc_addr uint32_t;
this matches the VMStateDescription, and also conforms to how
hardware works: the registers don't magically become larger
if the device is attached to a CPU with a larger physical
address size. It also fixes a compile failure if the
target_phys_addr_t type is changed to 64 bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Board support for Kyoto Micro's KZM-ARM11-01, an evaluation board built
around the Freescale i.MX31.
Signed-off-by: Philip O'Sullivan <philipo@ok-labs.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the Freescale i.MX31 advanced vectored interrupt controller, at least
to the extent it is used by Linux 3.x
Vectors are not implemented.
Signed-off-by: Philip O'Sullivan <philipo@ok-labs.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the timers on the Freescale i.MX31 SoC.
This is not a complete implementation, but gives enough for
Linux to boot and run. In particular external triggers, which are
not useful under QEMU, are not implemented.
Signed-off-by: Philip O'Sullivan <philipo@ok-labs.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For Linux to be able to work out how fast its clocks are going, so
that timer ticks come approximately at the right time, it needs to
be able to query the clock control module (CCM).
This is the start of a CCM implementation. It currently knows only about
the MCU, HSP and IPG clocks --- i.e., the ones used to feed the periodic
and general purpose timers.
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the Freescale i.MX UART. This uart is used in a variety of
SoCs, including some by Motorola, as well as in the Freescale i.MX
series.
This patch gives only a `bare-bones' implementation, enough to run Linux
or OKL4, but that's about it.
Signed-off-by: Philip O'Sullivan <philipo@ok-labs.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
