Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-4-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This reverts commit b320e21c48,
which accidentally broke TCG, because it made the TCG -cpu max
report the presence of MTE to the guest even if the board hadn't
enabled MTE by wiring up the tag RAM. This meant that if the guest
then tried to use MTE QEMU would segfault accessing the
non-existent tag RAM:
==346473==ERROR: UndefinedBehaviorSanitizer: SEGV on unknown address (pc 0x55f328952a4a bp 0x00000213a400 sp 0x7f7871859b80 T346476)
==346473==The signal is caused by a READ memory access.
==346473==Hint: this fault was caused by a dereference of a high value address (see register values below). Disassemble the provided pc to learn which register was used.
#0 0x55f328952a4a in address_space_to_flatview /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/exec/memory.h:1108:12
#1 0x55f328952a4a in address_space_translate /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/exec/memory.h:2797:31
#2 0x55f328952a4a in allocation_tag_mem /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/arm-clang/../../target/arm/tcg/mte_helper.c:176:10
#3 0x55f32895366c in helper_stgm /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/arm-clang/../../target/arm/tcg/mte_helper.c:461:15
#4 0x7f782431a293 (<unknown module>)
It's also not clear that the KVM logic is correct either:
MTE defaults to on there, rather than being only on if the
board wants it on.
Revert the whole commit for now so we can sort out the issues.
(We didn't catch this in CI because we have no test cases in
avocado that use guests with MTE support.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230519145808.348701-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Extend the 'mte' property for the virt machine to cover KVM as
well. For KVM, we don't allocate tag memory, but instead enable the
capability.
If MTE has been enabled, we need to disable migration, as we do not
yet have a way to migrate the tags as well. Therefore, MTE will stay
off with KVM unless requested explicitly.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230428095533.21747-2-cohuck@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
move the module containing cpu models definitions
for 32bit TCG-only CPUs to tcg/ and rename it for clarity.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230426180013.14814-8-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the 64-bit CPUs that are TCG-only:
- cortex-a35
- cortex-a55
- cortex-a72
- cortex-a76
- a64fx
- neoverse-n1
Keep the CPUs that can be used with KVM:
- cortex-a57
- cortex-a53
- max
- host
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230426180013.14814-6-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Allow setting a chardev input file on the command line
* Fix .travis.yml to work with non-public Travis instances, too
* Move a lot of code from specifc_ss into softmmu_ss
* Add a test case for TPM TIS I2C connected to Aspeed I2C controller
* Update tests/vm/freebsd to version 13
* Some more misc minor fixes here and there
-----BEGIN PGP SIGNATURE-----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=8ZFL
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-04-20' of https://gitlab.com/thuth/qemu into staging
* Compat machines for version 8.1
* Allow setting a chardev input file on the command line
* Fix .travis.yml to work with non-public Travis instances, too
* Move a lot of code from specifc_ss into softmmu_ss
* Add a test case for TPM TIS I2C connected to Aspeed I2C controller
* Update tests/vm/freebsd to version 13
* Some more misc minor fixes here and there
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmRBDtMRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXfjw//UYytlyZsDOLAMfFNGQViMmVf29KbrDRe
# doDh4Nl1oZLNKm9C5XlQExhsRbLm6Hi9nyQvSCJs4CvZ1jBY6U7GfgMNIaozXWb3
# 4gQyJb9ACe/z8bQmPUVF2sdW1QZ9zpf8LWpCOTGUZiI2Tevzkz7b/F5ZxiQiseG6
# dXe8UIwdZhG4jz2+6viqjHiGlKoBkegGYoJthcwnR07aRz2woiNr7rKRiJEiv2G7
# UfMVB96uLkpEhaDoohz440/rjviazO1nt6HDvgEajXT1X5P/8phT9IvT7olAZXZH
# R2Qm6YyYcSWavoPms3AryAWG8FjomcyBjuebfAVW5/x+fl/401sn9quBMoZrYPEX
# dfzF64vVokdXNQEH6+qc95PdB6/+d0CZPY8ilMRtAttf2sMw7IgqhG3zDLbj9t6R
# dns2/DY9zu2pp07IEAXn/iVbW4rl2HADUQncr6B/cPy++lYiFvv7LX8OE+YWOsk0
# gvxzYx6rRhr5j7xT1sP30pLwsG3mX7qRDfba1Bt19CzSbu7UGN+w+S1xclgZDoqE
# 0AZIeVUuqqNTEoBLoa2xHUDGs9NjeI2+qIh0R5csS/bqDscLXj0cOluvJO48n4Rt
# +SGQSCSmU/lxn6EbBz4tw3orlp0clBH9fEaSg9lYxuUTYvQOpdYS7u4d63VQFvzp
# dwQ9LRDFNsA=
# =8ZFL
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 20 Apr 2023 11:07:15 AM BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-04-20' of https://gitlab.com/thuth/qemu: (23 commits)
tests/vm/freebsd: Update to FreeBSD 13.2
qtest: Add a test case for TPM TIS I2C connected to Aspeed I2C controller
qtest: Move tpm_util_tis_transmit() into tpm-tis-utils.c and rename it
qtest: Add functions for accessing devices on Aspeed I2C controller
MAINTAINERS: Add Juan Quintela to developer guides review
cpu: Remove parameter of list_cpus()
hw/core: Move numa.c into the target independent source set
softmmu: Move dirtylimit.c into the target independent source set
hw/display: Compile vga.c as target-independent code
softmmu: Make qtest.c target independent
include/exec: Provide the tswap() functions for target independent code, too
softmmu/qtest: Move the target-specific pseries RTAS code out of qtest.c
hw/char: Move two more files from specific_ss to softmmu_ss
target/i386: Set family/model/stepping of the "max" CPU according to LM bit
tests/migration: Only run auto_converge in slow mode
travis.yml: Add missing 'flex', 'bison' packages to 'GCC (user)' job
travis.yml: Add missing clang-10 package to the 'Clang (disable-tcg)' job
chardev: Allow setting file chardev input file on the command line
qtest: Don't assert on "-qtest chardev:myid"
test: Fix test-crypto-secret when compiling without keyring support
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The Cortex-A7 core is only available when TCG is enabled (see
commit 80485d88f9 "target/arm: Restrict v7A TCG cpus to TCG accel").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230405100848.76145-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230409200526.1156456-1-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the cortex-a15 is under CONFIG_TCG, use as default CPU for a
KVM-only build the 'max' cpu.
Note that we cannot use 'host' here because the qtests can run without
any other accelerator (than qtest) and 'host' depends on KVM being
enabled.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just use current_accel_name() directly.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracked down with the help of scripts/clean-includes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230202133830.2152150-21-armbru@redhat.com>
Let's explicitly list out all accelerators that we support when trying to
determine the supported set of GIC versions. KVM was already separate, so
the only missing one is HVF which simply reuses all of TCG's emulation
code and thus has the same compatibility matrix.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221223090107.98888-3-agraf@csgraf.de
[PMM: Added qtest to the list of accelerators]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now, the finalize_gic_version() code open coded what is essentially
a support bitmap match between host/emulation environment and desired
target GIC type.
This open coding leads to undesirable side effects. For example, a VM with
KVM and -smp 10 will automatically choose GICv3 while the same command
line with TCG will stay on GICv2 and fail the launch.
This patch combines the TCG and KVM matching code paths by making
everything a 2 pass process. First, we determine which GIC versions the
current environment is able to support, then we go through a single
state machine to determine which target GIC mode that means for us.
After this patch, the only user noticable changes should be consolidated
error messages as well as TCG -M virt supporting -smp > 8 automatically.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20221223090107.98888-2-agraf@csgraf.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the macro instead of two explicit string literals.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230124232059.4017615-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 8.0 machine types for arm/i440fx/m68k/q35/s390x/spapr.
Reviewed-by: Cédric Le Goater <clg@kaod.org> [ppc]
Reviewed-by: Thomas Huth <thuth@redhat.com> [s390x]
Reviewed-by: Greg Kurz <groug@kaod.org> [ppc]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20221212152145.124317-2-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
* hw/arm/virt: Add properties to allow more granular
configuration of use of highmem space
* target/arm: Add Cortex-A55 CPU
* hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
* Implement FEAT_EVT
* Some 3-phase-reset conversions for Arm GIC, SMMU
* hw/arm/boot: set initrd with #address-cells type in fdt
* hw/misc: Move some arm-related files from specific_ss into softmmu_ss
* Restrict arm_cpu_exec_interrupt() to TCG accelerator
-----BEGIN PGP SIGNATURE-----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=YAjF
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20221215-1' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* hw/arm/virt: Add properties to allow more granular
configuration of use of highmem space
* target/arm: Add Cortex-A55 CPU
* hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
* Implement FEAT_EVT
* Some 3-phase-reset conversions for Arm GIC, SMMU
* hw/arm/boot: set initrd with #address-cells type in fdt
* hw/misc: Move some arm-related files from specific_ss into softmmu_ss
* Restrict arm_cpu_exec_interrupt() to TCG accelerator
# gpg: Signature made Thu 15 Dec 2022 17:38:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20221215-1' of https://git.linaro.org/people/pmaydell/qemu-arm: (28 commits)
target/arm: Restrict arm_cpu_exec_interrupt() to TCG accelerator
hw/misc: Move some arm-related files from specific_ss into softmmu_ss
hw/arm/boot: set initrd with #address-cells type in fdt
hw/intc: Convert TYPE_KVM_ARM_ITS to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_ITS to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_ITS_COMMON to 3-phase reset
hw/intc: Convert TYPE_KVM_ARM_GICV3 to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_COMMON to 3-phase reset
hw/intc: Convert TYPE_ARM_GIC_KVM to 3-phase reset
hw/intc: Convert TYPE_ARM_GIC_COMMON to 3-phase reset
hw/arm: Convert TYPE_ARM_SMMUV3 to 3-phase reset
hw/arm: Convert TYPE_ARM_SMMU to 3-phase reset
target/arm: Report FEAT_EVT for TCG '-cpu max'
target/arm: Implement HCR_EL2.TID4 traps
target/arm: Implement HCR_EL2.TICAB,TOCU traps
target/arm: Implement HCR_EL2.TTLBOS traps
target/arm: Implement HCR_EL2.TTLBIS traps
target/arm: Allow relevant HCR bits to be written for FEAT_EVT
hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
target/arm: Add Cortex-A55 CPU
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-A55 is one of the newer armv8.2+ CPUs; in particular
it supports the Privileged Access Never (PAN) feature. Add
a model of this CPU, so you can use a CPU type on the virt
board that models a specific real hardware CPU, rather than
having to use the QEMU-specific "max" CPU type.
Signed-off-by: Timofey Kutergin <tkutergin@gmail.com>
Message-id: 20221121150819.2782817-1-tkutergin@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the base_memmap to build the SMBIOS 19 table which provides the address
mapping for a Physical Memory Array (from spec [1] chapter 7.20).
This was present on i386 from commit c97294ec1b
("SMBIOS: Build aggregate smbios tables and entry point").
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.5.0.pdf
The absence of this table is a breach of the specs and is
detected by the FirmwareTestSuite (FWTS), but it doesn't
cause any known problems for guest OSes.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Message-id: 1668789029-5432-1-git-send-email-mihai.carabas@oracle.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 3 high memory regions are usually enabled by default, but they may
be not used. For example, VIRT_HIGH_GIC_REDIST2 isn't needed by GICv2.
This leads to waste in the PA space.
Add properties ("highmem-redists", "highmem-ecam", "highmem-mmio") to
allow users selectively disable them if needed. After that, the high
memory region for GICv3 or GICv4 redistributor can be disabled by user,
the number of maximal supported CPUs needs to be calculated based on
'vms->highmem_redists'. The follow-up error message is also improved
to indicate if the high memory region for GICv3 and GICv4 has been
enabled or not.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221029224307.138822-8-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the improvement to high memory region address assignment is
applied, the memory layout can be changed, introducing possible
migration breakage. For example, VIRT_HIGH_PCIE_MMIO memory region
is disabled or enabled when the optimization is applied or not, with
the following configuration. The configuration is only achievable by
modifying the source code until more properties are added to allow
users selectively disable those high memory regions.
pa_bits = 40;
vms->highmem_redists = false;
vms->highmem_ecam = false;
vms->highmem_mmio = true;
# qemu-system-aarch64 -accel kvm -cpu host \
-machine virt-7.2,compact-highmem={on, off} \
-m 4G,maxmem=511G -monitor stdio
Region compact-highmem=off compact-highmem=on
----------------------------------------------------------------
MEM [1GB 512GB] [1GB 512GB]
HIGH_GIC_REDISTS2 [512GB 512GB+64MB] [disabled]
HIGH_PCIE_ECAM [512GB+256MB 512GB+512MB] [disabled]
HIGH_PCIE_MMIO [disabled] [512GB 1TB]
In order to keep backwords compatibility, we need to disable the
optimization on machine, which is virt-7.1 or ealier than it. It
means the optimization is enabled by default from virt-7.2. Besides,
'compact-highmem' property is added so that the optimization can be
explicitly enabled or disabled on all machine types by users.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-7-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are three high memory regions, which are VIRT_HIGH_REDIST2,
VIRT_HIGH_PCIE_ECAM and VIRT_HIGH_PCIE_MMIO. Their base addresses
are floating on highest RAM address. However, they can be disabled
in several cases.
(1) One specific high memory region is likely to be disabled by
code by toggling vms->highmem_{redists, ecam, mmio}.
(2) VIRT_HIGH_PCIE_ECAM region is disabled on machine, which is
'virt-2.12' or ealier than it.
(3) VIRT_HIGH_PCIE_ECAM region is disabled when firmware is loaded
on 32-bits system.
(4) One specific high memory region is disabled when it breaks the
PA space limit.
The current implementation of virt_set_{memmap, high_memmap}() isn't
optimized because the high memory region's PA space is always reserved,
regardless of whatever the actual state in the corresponding
vms->highmem_{redists, ecam, mmio} flag. In the code, 'base' and
'vms->highest_gpa' are always increased for case (1), (2) and (3).
It's unnecessary since the assigned PA space for the disabled high
memory region won't be used afterwards.
Improve the address assignment for those three high memory region by
skipping the address assignment for one specific high memory region if
it has been disabled in case (1), (2) and (3). The memory layout may
be changed after the improvement is applied, which leads to potential
migration breakage. So 'vms->highmem_compact' is added to control if
the improvement should be applied. For now, 'vms->highmem_compact' is
set to false, meaning that we don't have memory layout change until it
becomes configurable through property 'compact-highmem' in next patch.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_get_high_memmap_enabled() helper, which returns
the pointer to vms->highmem_{redists, ecam, mmio}. The pointer will
be used in the subsequent patches.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-5-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces variable 'region_base' for the base address of the
specific high memory region. It's the preparatory work to optimize
high memory region address assignment.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This renames variable 'size' to 'region_size' in virt_set_high_memmap().
Its counterpart ('region_base') will be introduced in next patch.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_set_high_memmap() helper. The logic of high
memory region address assignment is moved to the helper. The intention
is to make the subsequent optimization for high memory region address
assignment easier.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-2-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When error_propagate(errp, local_err) is the only reader of
@local_err, we can just as well change its writers to write @errp
directly, and drop the error_propagate() along with @local_err.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The "PCI Bus Binding to: IEEE Std 1275-1994" defines the compatible
string for a PCIe bus or endpoint as "pci<vendorid>,<deviceid>" or
similar. Since the initial binding for PCI virtio-iommu didn't follow
this rule, it was modified to accept both strings and ensure backward
compatibility. Also, the unit-name for the node should be
"device,function".
Fix corresponding dt-validate and dtc warnings:
pcie@10000000: virtio_iommu@16:compatible: ['virtio,pci-iommu'] does not contain items matching the given schema
pcie@10000000: Unevaluated properties are not allowed (... 'virtio_iommu@16' were unexpected)
From schema: linux/Documentation/devicetree/bindings/pci/host-generic-pci.yaml
virtio_iommu@16: compatible: 'oneOf' conditional failed, one must be fixed:
['virtio,pci-iommu'] is too short
'pci1af4,1057' was expected
From schema: dtschema/schemas/pci/pci-bus.yaml
Warning (pci_device_reg): /pcie@10000000/virtio_iommu@16: PCI unit address format error, expected "2,0"
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMUv3 node isn't expected to have clock properties
(unlike the SMMUv2). Fix the corresponding dt-validate warning:
smmuv3@9050000: 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
From schema: linux/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message as suggested by Eric]
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-7-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "msi-parent" property can be used on the PCI node when MSIs do not
contain sideband data (device IDs) [1]. In QEMU, MSI transactions
contain the requester ID, so the PCI node should use the "msi-map"
property instead of "msi-parent". In our case the property describes an
identity map between requester ID and sideband data.
This fixes a warning when passing the DTB generated by QEMU to dtc,
following a recent change to the GICv3 node:
Warning (msi_parent_property): /pcie@10000000:msi-parent: property size (4) too small for cell size 1
[1] linux/Documentation/devicetree/bindings/pci/pci-msi.txt
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv3 bindings requires a #msi-cells property for the ITS node. Fix
the corresponding dt-validate warning:
interrupt-controller@8000000: msi-controller@8080000: '#msi-cells' is a required property
From schema: linux/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The devicetree specification requires a 'model' property in the root
node. Fix the corresponding dt-validate warning:
/: 'model' is a required property
From schema: dtschema/schemas/root-node.yaml
Use the same name for model as for compatible. The specification
recommends that 'compatible' follows the format 'manufacturer,model' and
'model' follows the format 'manufacturer,model-number'. Since our
'compatible' doesn't observe this, 'model' doesn't really need to
either.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add cortex A35 core and enable it for virt board.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joe Komlodi <komlodi@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220819002015.1663247-1-wuhaotsh@google.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the code from hw/arm/virt.c that is supposed
to handle v7 into the one function.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reported-by: He Zhe <zhe.he@windriver.com>
Message-id: 20220619001541.131672-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt board generates a gpio-keys node in the dtb, but it
incorrectly gives this node #size-cells and #address-cells
properties. If you dump the dtb with 'machine dumpdtb=file.dtb'
and run it through dtc, dtc will warn about this:
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the bogus properties.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-3-peter.maydell@linaro.org
In the virt board with secure=on we put two nodes in the dtb
for flash devices: one for the secure-only flash, and one
for the non-secure flash. We get the reg properties for these
correct, but in the DT node name, which by convention includes
the base address of devices, we used the wrong address. Fix it.
Spotted by dtc, which will complain
Warning (unique_unit_address): /flash@0: duplicate unit-address (also used in node /secflash@0)
if you dump the dtb from QEMU with -machine dumpdtb=file.dtb
and then decompile it with dtc.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-2-peter.maydell@linaro.org
When CPU-to-NUMA association isn't explicitly provided by users,
the default one is given by mc->get_default_cpu_node_id(). However,
the CPU topology isn't fully considered in the default association
and this causes CPU topology broken warnings on booting Linux guest.
For example, the following warning messages are observed when the
Linux guest is booted with the following command lines.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host \
-cpu host \
-smp 6,sockets=2,cores=3,threads=1 \
-m 1024M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=128M \
-object memory-backend-ram,id=mem1,size=128M \
-object memory-backend-ram,id=mem2,size=128M \
-object memory-backend-ram,id=mem3,size=128M \
-object memory-backend-ram,id=mem4,size=128M \
-object memory-backend-ram,id=mem4,size=384M \
-numa node,nodeid=0,memdev=mem0 \
-numa node,nodeid=1,memdev=mem1 \
-numa node,nodeid=2,memdev=mem2 \
-numa node,nodeid=3,memdev=mem3 \
-numa node,nodeid=4,memdev=mem4 \
-numa node,nodeid=5,memdev=mem5
:
alternatives: patching kernel code
BUG: arch topology borken
the CLS domain not a subset of the MC domain
<the above error log repeats>
BUG: arch topology borken
the DIE domain not a subset of the NODE domain
With current implementation of mc->get_default_cpu_node_id(),
CPU#0 to CPU#5 are associated with NODE#0 to NODE#5 separately.
That's incorrect because CPU#0/1/2 should be associated with same
NUMA node because they're seated in same socket.
This fixes the issue by considering the socket ID when the default
CPU-to-NUMA association is provided in virt_possible_cpu_arch_ids().
With this applied, no more CPU topology broken warnings are seen
from the Linux guest. The 6 CPUs are associated with NODE#0/1, but
there are no CPUs associated with NODE#2/3/4/5.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-id: 20220503140304.855514-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, the SMP configuration isn't considered when the CPU
topology is populated. In this case, it's impossible to provide
the default CPU-to-NUMA mapping or association based on the socket
ID of the given CPU.
This takes account of SMP configuration when the CPU topology
is populated. The die ID for the given CPU isn't assigned since
it's not supported on arm/virt machine. Besides, the used SMP
configuration in qtest/numa-test/aarch64_numa_cpu() is corrcted
to avoid testing failure
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20220503140304.855514-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the n1 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the a76 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM virt machine currently uses sysbus-fdt to create device tree
entries for dynamically created MMIO devices.
The RISC-V virt machine can also benefit from this, so move the code to
the core directory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-3-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add support for the TCG GICv4 to the virt board. For the board,
the GICv4 is very similar to the GICv3, with the only difference
being the size of the redistributor frame. The changes here are thus:
* calculating virt_redist_capacity correctly for GICv4
* changing various places which were "if GICv3" to be "if not GICv2"
* the commandline option handling
Note that using GICv4 reduces the maximum possible number of CPUs on
the virt board from 512 to 317, because we can now only fit half as
many redistributors into the redistributor regions we have defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-42-peter.maydell@linaro.org
In several places in virt.c we calculate the number of redistributors that
fit in a region of our memory map, which is the size of the region
divided by the size of a single redistributor frame. For GICv4, the
redistributor frame is a different size from that for GICv3. Abstract
out the calculation of redistributor region capacity so that we have
one place we need to change to handle GICv4 rather than several.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-41-peter.maydell@linaro.org
Everywhere we need to check which GIC version we're using, we look at
vms->gic_version and use the VIRT_GIC_VERSION_* enum values, except
in create_gic(), which copies vms->gic_version into a local 'int'
variable and makes direct comparisons against values 2 and 3.
For consistency, change this function to check the GIC version
the same way we do elsewhere. This includes not implicitly relying
on the enumeration type values happening to match the integer
'revision' values the GIC device object wants.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-40-peter.maydell@linaro.org
It's not possible to provide the guest with the Security extensions
(TrustZone) when using KVM or HVF, because the hardware
virtualization extensions don't permit running EL3 guest code.
However, we weren't checking for this combination, with the result
that QEMU would assert if you tried it:
$ qemu-system-aarch64 -enable-kvm -machine virt,secure=on -cpu host -display none
Unexpected error in object_property_find_err() at ../../qom/object.c:1304:
qemu-system-aarch64: Property 'host-arm-cpu.secure-memory' not found
Aborted
Check for this combination of options and report an error, in the
same way we already do for attempts to give a KVM or HVF guest the
Virtualization or MTE extensions. Now we will report:
qemu-system-aarch64: mach-virt: KVM does not support providing Security extensions (TrustZone) to the guest CPU
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/961
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404155301.566542-1-peter.maydell@linaro.org
In TCG mode, if gic-version=max we always select GICv3 even if
CONFIG_ARM_GICV3_TCG is unset. We shall rather select GICv2.
This also brings the benefit of fixing qos tests errors for tests
using gic-version=max with CONFIG_ARM_GICV3_TCG unset.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220308182452.223473-3-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a Linux kernel bug present until v5.12 that prevents
booting with FEAT_LPA2 enabled. As a workaround for TCG,
disable this feature for machine versions prior to 7.0.
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
