This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
aspeed_i2c_bus_is_master is checking if master mode is enabled in the I2C
bus controller's function-control register, not that slave mode is enabled
or something. The error here is that the guest is trying to trigger an I2C
master mode command while master mode is not enabled.
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-4-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I noticed i2c rx transfers were getting shortened to "1" on Zephyr. It
seems to be because the Zephyr i2c driver sets the RX DMA len with the
RX field write-enable bit set (bit 31) to avoid a read-modify-write. [1]
/* 0x1C : I2CM Master DMA Transfer Length Register */
I think we should be checking the write-enable bits on the incoming
value, not checking the register array. I'm not sure we're even writing
the write-enable bits to the register array, actually.
[1] db3dbcc9c5/drivers/i2c/i2c_aspeed.c (L145-L148)
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-3-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Very minor, doesn't effect functionality, but this is supposed to be
R_I2CC_FUN_CTRL (new-mode, not old-mode).
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-2-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.
Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
"Setting the PAGE to FFh means that all subsequent comands are to be
applied to all outputs.
Some commands, such as READ_TEMPERATURE, may use a common sensor but
be available on all pages of a device. Such implementations are the
decision of each device manufacturer or are specified in a PMBus
Application Profile. Consult the manufacturer's documents or the
Application Profile Specification as needed."
For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a 'stop' string seems more appropriate than 'normal'.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no 'slave match interrupt' enable bit in the Interrupt
Control Register. Consider it is always enabled and extend the mask
value 'bus->regs[intr_ctrl_reg]' with the SLAVE_ADDR_RX_MATCH bit when
the interrupt is raised.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Build a single string instead of having several parameters on the trace
event.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: simplified trace buffer creation ]
Message-Id: <20220601210831.67259-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleans up some of the field accessing, setting, and clearing
bitwise operations, and wraps them in macros instead.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I33018d6325fa04376e7c29dc4a49ab389a8e333a
Message-Id: <20220331043248.2237838-4-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
wire AcpiDevAmlIf interface to build ich9-smb and its slave
devices AML. It will be used by followup patches to switch
from creating AML in ad-hoc way to a more systematic one
that will scan present devices and ask them to provide
their AML code like it's done with ISA devices.
This patch is a partial conversion, as it only fetches
AML from slave devices attached to its I2C bus.
The conversion will be completed when PCI bus is
switched to use AcpiDevAmlIf and build_smb0() could be
dropped.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-16-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
This change cleans up the inputs to pmbus_receive uint, the length of
received data is contained in PMBusDevice state and doesn't need to be
passed around.
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- add the VOUT_MIN and STATUS_MFR registers
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously this device created N subdevices which each owned an i2c bus.
Now this device simply owns the N i2c busses directly.
Tested: Verified devices behind mux are still accessible via qmp and i2c
from within an arm32 SoC.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220202164533.1283668-1-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
imply I2C_DEVICES
to cause those pluggable devices to be built.
In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-2-peter.maydell@linaro.org
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
Add the differential clock input feature bit to the generated SPD
data. Most guests don't seem to care but pegasos2 firmware version 1.2
checks for this bit and stops with unsupported module type error if
it's not present. Since this feature is likely present on real memory
modules add it in the general code rather than patching the generated
SPD data in pegasos2 board only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <19d42ade295d5297aa624a9eb757b8df18cf64d6.1626367844.git.balaton@eik.bme.hu>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.
Use these new helpers in the SMBus / AUX bus models.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To allow further simplications, extract i2c_do_start_transfer()
from i2c_start_transfer(). This is mostly the same function,
but the former is static and takes an enum argument.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It took me a while to find this model datasheet, since it is
an OCR scan. Add a reference to save other developers time.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
-----BEGIN PGP SIGNATURE-----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=IamZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-v1' into staging
Add a bus multiplexer device
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
# gpg: Signature made Thu 13 May 2021 22:48:07 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-v1:
hw/i2c: add pca954x i2c-mux switch
hw/i2c: move search to i2c_scan_bus method
hw/i2c: add match method for device search
hw/i2c: name I2CNode list in I2CBus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The RAM memory region is now used for DMAs accesses instead of the
memory address space region. Mask off the top bits of the DMA address
to reflect this change.
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The STATUS register will be reset to IDLE in
cnpcm7xx_smbus_enter_reset(), no need to preset
it in instance_init().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210228224813.312532-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
