Commit Graph

286 Commits

Author SHA1 Message Date
Peter Feiner
3b69595068 doc: add "setup" to list of migration states
On a slow VM (e.g., nested), you see the "setup" state when you query the
migration status.

Signed-off-by: Peter Feiner <peter@gridcentric.ca>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-05-20 14:39:19 -04:00
Peter Lieven
465bee1da8 block: optimize zero writes with bdrv_write_zeroes
this patch tries to optimize zero write requests
by automatically using bdrv_write_zeroes if it is
supported by the format.

This significantly speeds up file system initialization and
should speed zero write test used to test backend storage
performance.

I ran the following 2 tests on my internal SSD with a
50G QCOW2 container and on an attached iSCSI storage.

a) mkfs.ext4 -E lazy_itable_init=0,lazy_journal_init=0 /dev/vdX

QCOW2         [off]     [on]     [unmap]
-----
runtime:       14secs    1.1secs  1.1secs
filesize:      937M      18M      18M

iSCSI         [off]     [on]     [unmap]
----
runtime:       9.3s      0.9s     0.9s

b) dd if=/dev/zero of=/dev/vdX bs=1M oflag=direct

QCOW2         [off]     [on]     [unmap]
-----
runtime:       246secs   18secs   18secs
filesize:      51G       192K     192K
throughput:    203M/s    2.3G/s   2.3G/s

iSCSI*        [off]     [on]     [unmap]
----
runtime:       8mins     45secs   33secs
throughput:    106M/s    1.2G/s   1.6G/s
allocated:     100%      100%     0%

* The storage was connected via an 1Gbit interface.
  It seems to internally handle writing zeroes
  via WRITESAME16 very fast.

Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-05-19 13:42:27 +02:00
Eric Blake
cd0c5389dd qmp: use valid JSON in transaction example
Our example should use the correct quotes to match what someone
could actually pass over the wire.

* qmp-commands.hx: Use correct JSON quotes.

Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-05-09 09:11:32 -04:00
ChenLiang
8bc3923343 migration: expose xbzrle cache miss rate
expose xbzrle cache miss rate

Signed-off-by: ChenLiang <chenliang88@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2014-05-05 22:15:03 +02:00
ChenLiang
58570ed894 migration: expose the bitmap_sync_count to the end
expose the count that logs the times of updating the dirty bitmap to
end user.

Signed-off-by: ChenLiang <chenliang88@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2014-05-05 22:15:03 +02:00
Amos Kong
f7bc8ef809 virtio-net: add vlan receive state to RxFilterInfo
Stefan Fritsch just fixed a virtio-net driver bug [1], virtio-net won't
filter out VLAN-tagged packets if VIRTIO_NET_F_CTRL_VLAN isn't negotiated.

This patch added a new field to @RxFilterInfo to indicate vlan receive
state ('normal', 'none', 'all'). If VIRTIO_NET_F_CTRL_VLAN isn't
negotiated, vlan receive state will be 'all', then all VLAN-tagged packets
will be received by guest.

This patch also fixed a boundary issue in visiting vlan table.

[1] http://lists.nongnu.org/archive/html/qemu-devel/2014-02/msg02604.html

Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2014-03-26 12:49:10 +02:00
Stefan Hajnoczi
dc3dd0d2be qmp: add query-iothreads command
The "query-iothreads" command returns a list of information about
iothreads.  See the patch for API documentation.

Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2014-03-13 14:42:24 +01:00
qiaonuohan
7d6dc7f30c dump: add 'query-dump-guest-memory-capability' command
'query-dump-guest-memory-capability' is used to query the available formats for
'dump-guest-memory'. The output of the command will be like:

-> { "execute": "query-dump-guest-memory-capability" }
<- { "return": { "formats":
                    ["elf", "kdump-zlib", "kdump-lzo", "kdump-snappy"] }

Signed-off-by: Qiao Nuohan <qiaonuohan@cn.fujitsu.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-02-28 11:52:03 -05:00
qiaonuohan
b53ccc30c4 dump: make kdump-compressed format available for 'dump-guest-memory'
Make monitor command 'dump-guest-memory' be able to dump in kdump-compressed
format. The command's usage:

  dump [-p] protocol [begin] [length] [format]

'format' is used to specified the format of vmcore and can be:
1. 'elf': ELF format, without compression
2. 'kdump-zlib': kdump-compressed format, with zlib-compressed
3. 'kdump-lzo': kdump-compressed format, with lzo-compressed
4. 'kdump-snappy': kdump-compressed format, with snappy-compressed
Without 'format' being set, it is same as 'elf'. And if non-elf format is
specified, paging and filter is not allowed.

Note:
  1. The kdump-compressed format is readable only with the crash utility and
     makedumpfile, and it can be smaller than the ELF format because of the
     compression support.
  2. The kdump-compressed format is the 6th edition.

Signed-off-by: Qiao Nuohan <qiaonuohan@cn.fujitsu.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-02-28 11:52:03 -05:00
Martin Kletzander
77d1c3c63f qmp: expose list of supported character device backends
Introduce 'query-chardev-backends' QMP command which lists all
supported character device backends.

Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-02-17 11:57:23 -05:00
Jeff Cody
3722290074 block: update block commit documentation regarding image truncation
This updates the documentation for commiting snapshot images.
Specifically, this highlights what happens when the base image
is either smaller or larger than the snapshot image being committed.

In the case of the base image being smaller, it is resized to the
larger size of the snapshot image.  In the case of the base image
being larger, it is not resized automatically, but once the commit
has completed it is safe for the user to truncate the base image.

Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-01-24 16:12:49 +01:00
Benoît Canet
0901f67ecd qmp: Allow to take external snapshots on bs graphs node.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-01-24 16:07:08 +01:00
Benoît Canet
3b1dbd11a6 qmp: Allow block_resize to manipulate bs graph nodes.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-01-24 16:07:08 +01:00
Benoît Canet
12d3ba821d qmp: Allow to change password on named block driver states.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>

There was two candidate ways to implement named node manipulation:

1)
{ 'command': 'block_passwd', 'data': {'*device': 'str',
                                      '*node-name': 'str', 'password': 'str'}
}

2)

{ 'command': 'block_passwd', 'data': {'device': 'str',
                                      '*device-is-node': 'bool',
                                      'password': 'str'} }

Luiz proposed 1 and says 2 was an abuse of the QMP interface and proposed to
rewrite the QMP block interface for 2.0.

Luiz does not like in 1 the fact that 2 fields are optional but one of them must
be specified leading to an abuse of the QMP semantic.

Kevin argumented that 2 what a clear abuse of the device field and would not be
practical when reading fast some log file because the user would read "device"
and think that a device is manipulated when it's in fact a node name.
Documentation of 1 make it pretty clear what to do for the user.

Kevin argued that all bs are node including devices ones so 2 does not make
sense.

Kevin also argued that rewriting the QMP block interface would not make disapear
the current one.

Kevin pushed the argument that making the QAPI generator compatible with the
semantic of the operation would need a rewrite that no one has done yet.

A vote has been done on the list to elect the version to use and 1 won.

For reference the complete thread is:
"[Qemu-devel] [PATCH V4 4/7] qmp: Allow to change password on names block driver
states."

Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-01-24 16:07:08 +01:00
Benoît Canet
c13163fba1 qmp: Add QMP query-named-block-nodes to list the named BlockDriverState nodes.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2014-01-24 16:07:08 +01:00
Paolo Bonzini
cff8b2c6fc monitor: add object-add (QMP) and object_add (HMP) command
Add two commands that are the monitor counterparts of -object.  The commands
have the same Visitor-based implementation, but use different kinds of
visitors so that the HMP command has a DWIM string-based syntax, while
the QMP variant accepts a stricter JSON-based properties dictionary.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-01-06 13:45:47 -05:00
Paolo Bonzini
ab2d0531b2 monitor: add object-del (QMP) and object_del (HMP) command
These two commands invoke the "unparent" method of Object.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2014-01-06 13:45:47 -05:00
Kevin Wolf
d26c9a1573 blockdev: 'blockdev-add' QMP command
For examples see the changes to qmp-commands.hx.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-10-11 16:50:01 +02:00
Wenchao Xia
44e3e053af qmp: add interface blockdev-snapshot-delete-internal-sync
This interface use id and name as optional parameters, to handle the
case that one image contain multiple snapshots with same name which
may be '', but with different id.

Adding parameter id is for historical compatiability reason, and
that case is not possible in qemu's new interface for internal
snapshot at block device level, but still possible in qemu-img.

Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-09-12 10:12:47 +02:00
Wenchao Xia
f323bc9e8b qmp: add interface blockdev-snapshot-internal-sync
Snapshot ID can't be specified in this interface.

Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-09-12 10:12:47 +02:00
Wenchao Xia
bbe860104f qmp: add internal snapshot support in qmp_transaction
Unlike savevm, the qmp_transaction interface will not generate
snapshot name automatically, saving trouble to return information
of the new created snapshot.

Although qcow2 support storing multiple snapshots with same name
but different ID, here it will fail when an snapshot with that name
already exist before the operation. Format such as rbd do not support
ID at all, and in most case, it means trouble to user when he faces
multiple snapshots with same name, so ban that case. Request with
empty name will be rejected.

Snapshot ID can't be specified in this interface.

Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-09-12 10:12:47 +02:00
Benoît Canet
2024c1df43 block: Add iops_size to do the iops accounting for a given io size.
This feature can be used in case where users are avoiding the iops limit by
doing jumbo I/Os hammering the storage backend.

Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2013-09-06 15:25:07 +02:00
Benoît Canet
3e9fab690d block: Add support for throttling burst max in QMP and the command line.
The max parameter of the leaky bucket throttling algorithm can be used to
allow the guest to do bursts.
The max value is a pool of I/O that the guest can use without being throttled
at all. Throttling is triggered once this pool is empty.

Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2013-09-06 15:25:07 +02:00
Eric Blake
586b546657 qmp: fix integer usage in examples
Per the qapi schema, block_set_io_throttle takes most arguments
as ints, not strings.

* qmp-commands.hx (block_set_io_throttle): Use correct type.  Fix
whitespace and a copy-paste bug in the process.

Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2013-09-01 19:46:58 +04:00
Eugene (jno) Dvurechenski
7f7f975295 s390: wire up nmi command to raise a RESTART interrupt on S390
There is the 'nmi' command that is used to trigger a guest dump via kdump feature on x86.
s390 uses RESTART interrupt to trigger kdump.
So, this patch provides a mean to use 'nmi' command on s390 to raise RESTART interrupt.

The CPU to receive the RESTART interrupt is the "default" one.

There is an infrastructure to select the "default" CPU using 'cpu' command.
The 'info cpus' command can be used to see which one is the "default".

In order to wire up the RESTART to 'nmi' command we had to:
1. implement the kvm_s390_cpu_restart function by exporting the existing code
2. implement s390_cpu_restart function as kvm-aware wrapper
3. modify the qmp_inject_nmi function to enable (for s390) the scan for
   "default" CPU and call s390_cpu_restart for it;
3. fix some messages.

Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
2013-08-30 14:16:48 +02:00
Michael R. Hines
8f3067bd86 rdma: remaining documentation fixes
Was missing 'setup-time' in some of the QMP documentation...

Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1376078746-24948-7-git-send-email-mrhines@linux.vnet.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-08-12 09:31:16 -05:00
Ian Main
fc5d3f8432 Implement sync modes for drive-backup.
This patch adds sync-modes to the drive-backup interface and
implements the FULL, NONE and TOP modes of synchronization.

FULL performs as before copying the entire contents of the drive
while preserving the point-in-time using CoW.
NONE only copies new writes to the target drive.
TOP copies changes to the topmost drive image and preserves the
point-in-time using CoW.

For sync mode TOP are creating a new target image using the same backing
file as the original disk image.  Then any new data that has been laid
on top of it since creation is copied in the main backup_run() loop.
There is an extra check in the 'TOP' case so that we don't bother to copy
all the data of the backing file as it already exists in the target.
This is where the bdrv_co_is_allocated() is used to determine if the
data exists in the topmost layer or below.

Also any new data being written is intercepted via the write_notifier
hook which ends up calling backup_do_cow() to copy old data out before
it gets overwritten.

For mode 'NONE' we create the new target image and only copy in the
original data from the disk image starting from the time the call was
made.  This preserves the point in time data by only copying the parts
that are *going to change* to the target image.  This way we can
reconstruct the final image by checking to see if the given block exists
in the new target image first, and if it does not, you can get it from
the original image.  This is basically an optimization allowing you to
do point-in-time snapshots with low overhead vs the 'FULL' version.

Since there is no old data to copy out the loop in backup_run() for the
NONE case just calls qemu_coroutine_yield() which only wakes up after
an event (usually cancel in this case).  The rest is handled by the
before_write notifier which again calls backup_do_cow() to write out
the old data so it can be preserved.

Signed-off-by: Ian Main <imain@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-07-26 22:01:31 +02:00
Anthony Liguori
bbcf59bc4b Merge remote-tracking branch 'luiz/queue/qmp' into staging
# By Amos Kong (1) and Luiz Capitulino (1)
# Via Luiz Capitulino
* luiz/queue/qmp:
  qmp: update send-key document
  qapi: qapi-commands: fix possible leaks on visitor dealloc

Message-id: 1374093679-29213-1-git-send-email-lcapitulino@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-07-18 08:14:11 -05:00
Anthony Liguori
e9acb8cea9 pci,net,pc enhancements
This includes some fixes and enhancements that accumulated in my tree:
 pci fixes by dkoch, virtio-net enhancements by akong and mst,
 and a fix for xen pc by mst.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.13 (GNU/Linux)
 
 iQEcBAABAgAGBQJR5meNAAoJECgfDbjSjVRp24IIAMOkxbb85FJ323G/x5cQBzA/
 gjFDmvB6geIMBorX1YZRnIM+RFhx+mkXtBTu2raWVTNTt5G2u3vAQQWW2zSiOTBL
 gH4BhzJnUoqLHOydWql2MsGS7DMQo4Fq8OnzRBkZ119AEEqNMad1w2LykwFWs4ra
 k3bsPNCZM+ZNiLMWtQLOcD3FYvoiISinqFd81KOnxvDiT90rczk4dLWqjv8smNif
 WqZ7aCD1hGJ5yD7JI2YjCbhVvu4F7tBK+fWkT/O3oYslh/o241lyxUriOXMKdKML
 04sNXa5eWue9cOKlbo1G+yfFwFg1JDsAMe/Usg0KXz1MMK91wiWE763ESPbFBK0=
 =P+pr
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'mst/tags/for_anthony' into staging

pci,net,pc enhancements

This includes some fixes and enhancements that accumulated in my tree:
pci fixes by dkoch, virtio-net enhancements by akong and mst,
and a fix for xen pc by mst.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Wed 17 Jul 2013 04:44:45 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found

# By Don Koch (2) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
  pc: don't access fw cfg if NULL
  virtio-net: add feature bit for any header s/g
  net: add support of mac-programming over macvtap in QEMU side
  pci: fix BRDIGE typo
  pci-bridge: update mappings for migration/restore

Message-id: 1374054430-21966-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-07-18 08:12:47 -05:00
Amos Kong
f9b1d9b20f qmp: update send-key document
commit 9f328977 changes qmp_send_key() to accept key codes in hex,
but the document wasn't updated. The items of keys list is union
now, not enum.

Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-07-17 16:00:26 -04:00
Amos Kong
b1be42803b net: add support of mac-programming over macvtap in QEMU side
Currently macvtap based macvlan device is working in promiscuous
mode, we want to implement mac-programming over macvtap through
Libvirt for better performance.

Design:
 QEMU notifies Libvirt when rx-filter config is changed in guest,
 then Libvirt query the rx-filter information by a monitor command,
 and sync the change to macvtap device. Related rx-filter config
 of the nic contains main mac, rx-mode items and vlan table.

This patch adds a QMP event to notify management of rx-filter change,
and adds a monitor command for management to query rx-filter
information.

Test:
 If we repeatedly add/remove vlan, and change macaddr of vlan
 interfaces in guest by a loop script.

Result:
 The events will flood the QMP client(management), management takes
 too much resource to process the events.

 Event_throttle API (set rate to 1 ms) can avoid the events to flood
 QMP client, but it could cause an unexpected delay (~1ms), guests
 guests normally expect rx-filter updates immediately.

 So we use a flag for each nic to avoid events flooding, the event
 is emitted once until the query command is executed. The flag
 implementation could not introduce unexpected delay.

There maybe exist an uncontrollable delay if we let Libvirt do the
real change, guests normally expect rx-filter updates immediately.
But it's another separate issue, we can investigate it when the
work in Libvirt side is done.

Michael S. Tsirkin: tweaked to enable events on start
Michael S. Tsirkin: fixed not to crash when no id
Michael S. Tsirkin: fold in patch:
   "additional fixes for mac-programming feature"
Amos Kong: always notify QMP client if mactable is changed
Amos Kong: return NULL list if no net client supports rx-filter query

Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2013-07-15 21:23:08 +03:00
Stefan Hajnoczi
b53169eae0 blockdev: add sync mode to drive-backup QMP command
The drive-backup command is similar to the drive-mirror command, except
no guest data written after the command executes gets copied.  Add a
sync mode argument which determines whether the entire disk is copied,
just allocated clusters, or only clusters being written to by the guest.

Currently only sync mode 'full' is supported - it copies the entire disk.
For read-only point-in-time snapshots we may only need sync mode 'none'
since the target can be a qcow2 file using the guest's disk as its
backing file (no need to copy the entire disk).  Finally, sync mode
'top' is useful if we wish to preserve the backing chain.

Note that this patch just adds the sync mode argument to drive-backup.
It does not implement sync modes 'top' or 'none'.  This patch is
necessary so we can add a drive-backup HMP command that behaves like the
existing drive-mirror HMP command and takes a sync mode.

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-07-15 09:49:00 +02:00
Stefan Hajnoczi
99a9addf56 block: add drive-backup QMP command
@drive-backup

Start a point-in-time copy of a block device to a new destination.  The
status of ongoing drive-backup operations can be checked with
query-block-jobs where the BlockJobInfo.type field has the value 'backup'.
The operation can be stopped before it has completed using the
block-job-cancel command.

@device: the name of the device which should be copied.

@target: the target of the new image. If the file exists, or if it
         is a device, the existing file/device will be used as the new
         destination.  If it does not exist, a new file will be created.

@format: #optional the format of the new destination, default is to
         probe if @mode is 'existing', else the format of the source

@mode: #optional whether and how QEMU should create a new image, default is
       'absolute-paths'.

@speed: #optional the maximum speed, in bytes per second

@on-source-error: #optional the action to take on an error on the source,
                  default 'report'.  'stop' and 'enospc' can only be used
                  if the block device supports io-status (see BlockInfo).

@on-target-error: #optional the action to take on an error on the target,
                  default 'report' (no limitations, since this applies to
                  a different block device than @device).

Note that @on-source-error and @on-target-error only affect background I/O.
If an error occurs during a guest write request, the device's rerror/werror
actions will be used.

Returns: nothing on success
         If @device is not a valid block device, DeviceNotFound

Since 1.6

Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-06-28 09:20:26 +02:00
Wenchao Xia
553a7e8718 qmp: add ImageInfo in BlockDeviceInfo used by query-block
Now image info will be retrieved as an embbed json object inside
BlockDeviceInfo, backing chain info and all related internal snapshot
info can be got in the enhanced recursive structure of ImageInfo. New
recursive member *backing-image is added to reflect the backing chain
status.

Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2013-06-07 13:37:45 +02:00
Anthony Liguori
8ca27ce2e1 Merge remote-tracking branch 'afaerber/qom-cpu' into staging
# By Igor Mammedov (21) and others
# Via Andreas Färber
* afaerber/qom-cpu: (29 commits)
  Drop redundant resume_all_vcpus() from main()
  cpus: Fix pausing TCG CPUs while in vCPU thread
  target-i386: Replace cpuid_*features fields with a feature word array
  target-i386: Break CPUID feature definition lines
  target-i386/kvm.c: Code formatting changes
  target-i386: Group together level, xlevel, xlevel2 fields
  pc: Implement QEMUMachine::hot_add_cpu hook
  QMP: Add cpu-add command
  Add hot_add_cpu hook to QEMUMachine
  target-i386: Move APIC to ICC bus
  target-i386: Attach ICC bus to CPU on its creation
  target-i386: Introduce ICC bus/device/bridge
  cpu: Move cpu_write_elfXX_note() functions to CPUState
  kvmvapic: Make dependency on sysbus.h explicit
  target-i386: Replace MSI_SPACE_SIZE with APIC_SPACE_SIZE
  target-i386: Do not allow to set apic-id once CPU is realized
  target-i386: Introduce apic-id CPU property
  target-i386: Introduce feat2prop() for CPU properties
  acpi_piix4: Add infrastructure to send CPU hot-plug GPE to guest
  cpu: Add helper cpu_exists(), to check if CPU with specified id exists
  ...
2013-05-02 10:57:01 -05:00
Stefan Weil
805a250502 Trivial grammar and spelling fixes
similiar -> similar
recieve -> receive
transfered -> transferred
preperation -> preparation

Most changes are in comments, one modifies a parameter name in a function
prototype.

The spelling fixes were made using codespell.

Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2013-05-01 20:55:21 +04:00
Igor Mammedov
69ca3ea5e1 QMP: Add cpu-add command
Adds "cpu-add id=xxx" QMP command.

cpu-add's "id" argument is a CPU number in a range [0..max-cpus)

Example QMP command:
 -> { "execute": "cpu-add", "arguments": { "id": 2 } }
 <- { "return": {} }

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
2013-05-01 13:06:07 +02:00
Amos Kong
1f8f987d34 monitor: introduce query-command-line-options
Libvirt has no way to probe if an option or property is supported,
This patch introduces a new qmp command to query command line
option information. hmp command isn't added because it's not needed.

Signed-off-by: Amos Kong <akong@redhat.com>
CC: Luiz Capitulino <lcapitulino@redhat.com>
CC: Osier Yang <jyang@redhat.com>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2013-04-25 10:07:06 -04:00
Michal Novotny
315f9e1a8f Revert "New QMP command query-cpu-max and HMP command cpu_max"
This reverts commit 4d700430a2 as asked by
Luiz. The patch has been obsoleted by extending MachineInfo structure
by cpu-max field.

Signed-off-by: Michal Novotny <minovotn@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-04-12 09:41:54 -04:00
Anthony Liguori
18501ae6e8 Merge remote-tracking branch 'quintela/migration.next' into staging
# By Peter Lieven (9) and others
# Via Juan Quintela
* quintela/migration.next: (22 commits)
  Use qemu_put_buffer_async for guest memory pages
  Add qemu_put_buffer_async
  Use writev ops if available
  Store the data to send also in iovec
  Update bytes_xfer in qemu_put_byte
  Add socket_writev_buffer function
  Add QemuFileWritevBuffer QemuFileOps
  migration: use XBZRLE only after bulk stage
  migration: do not search dirty pages in bulk stage
  migration: do not sent zero pages in bulk stage
  migration: add an indicator for bulk state of ram migration
  migration: search for zero instead of dup pages
  bitops: unroll while loop in find_next_bit()
  buffer_is_zero: use vector optimizations if possible
  cutils: add a function to find non-zero content in a buffer
  move vector definitions to qemu-common.h
  savevm: Fix bugs in the VMSTATE_VBUFFER_MULTIPLY definition
  savevm: Add VMSTATE_STRUCT_VARRAY_POINTER_UINT32
  savevm: Add VMSTATE_FLOAT64 helpers
  savevm: Add VMSTATE_UINTTL_EQUAL helper
  ...
2013-03-26 13:38:00 -05:00
Peter Lieven
f1c72795af migration: do not sent zero pages in bulk stage
during bulk stage of ram migration if a page is a
zero page do not send it at all.
the memory at the destination reads as zero anyway.

even if there is an madvise with QEMU_MADV_DONTNEED
at the target upon receipt of a zero page I have observed
that the target starts swapping if the memory is overcommitted.
it seems that the pages are dropped asynchronously.

this patch also updates QMP to return the number of
skipped pages in MigrationStats.

Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
2013-03-26 13:32:33 +01:00
Juan Quintela
817c60457f migration: Improve QMP documentation
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2013-03-26 13:30:38 +01:00
Michal Novotny
4d700430a2 New QMP command query-cpu-max and HMP command cpu_max
These commands return the maximum number of CPUs supported by the
currently running emulator instance, as defined in its QEMUMachine
struct.

Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-03-25 16:21:33 -04:00
Corey Bryant
28c4fa32bd QMP: TPM QMP and man page documentation updates
Signed-off-by: Corey Bryant <coreyb@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-03-25 16:21:33 -04:00
Stefan Berger
d1a0cf738d Support for TPM command line options
This patch adds support for TPM command line options.
The command line options supported here are

./qemu-... -tpmdev passthrough,path=<path to TPM device>,id=<id>
           -device tpm-tis,tpmdev=<id>,id=<other id>

and

./qemu-... -tpmdev help

where the latter works similar to -soundhw help and shows a list of
available TPM backends (for example 'passthrough').

Using the type parameter, the backend is chosen, i.e., 'passthrough' for the
passthrough driver. The interpretation of the other parameters along
with determining whether enough parameters were provided is pushed into
the backend driver, which needs to implement the interface function
'create' and return a TPMDriverOpts structure if the VM can be started or
'NULL' if not enough or bad parameters were provided.

Monitor support for 'info tpm' has been added. It for example prints the
following:

(qemu) info tpm
TPM devices:
 tpm0: model=tpm-tis
  \ tpm0: type=passthrough,path=/dev/tpm0,cancel-path=/sys/devices/pnp0/00:09/cancel

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Corey Bryant <coreyb@linux.vnet.ibm.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Message-id: 1361987275-26289-2-git-send-email-stefanb@linux.vnet.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-03-12 13:40:11 -05:00
Markus Armbruster
af347aa5a5 qmp: netdev_add is like -netdev, not -net, fix documentation
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2013-02-27 16:10:47 +01:00
Markus Armbruster
3949e59414 qemu-char: Saner naming of memchar stuff & doc fixes
New device, has never been released, so we can still improve things
without worrying about compatibility.

Naming is a mess.  The code calls the device driver CirMemCharDriver,
the public API calls it "memory", "memchardev", or "memchar", and the
special commands are named like "memchar-FOO".  "memory" is a
particularly unfortunate choice, because there's another character
device driver called MemoryDriver.  Moreover, the device's distinctive
property is that it's a ring buffer, not that's in memory.  Therefore:

* Rename CirMemCharDriver to RingBufCharDriver, and call the thing a
  "ringbuf" in the API.

* Rename QMP and HMP commands from memchar-FOO to ringbuf-FOO.

* Rename device parameter from maxcapacity to size (simple words are
  good for you).

* Clearly mark the parameter as optional in documentation.

* Fix error reporting so that chardev-add reports to current monitor,
  not stderr.

* Replace cirmem in C identifiers by ringbuf.

* Rework documentation.  Document the impact of our crappy UTF-8
  handling on reading.

* QMP examples that even work.

I could split this up into multiple commits, but they'd change the
same documentation lines multiple times.  Not worth it.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-02-06 16:35:19 -06:00
Markus Armbruster
3ab651fc81 qmp: Clean up design of memchar-read
The data returned has a well-defined size, which makes the size
returned along with it redundant at best.  Drop it.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-02-06 16:35:17 -06:00
Markus Armbruster
82e59a676c qmp: Fix design bug and read beyond buffer in memchar-write
Command memchar-write takes data and size parameter.  Begs the
question what happens when data doesn't match size.

With format base64, qmp_memchar_write() copies the full data argument,
regardless of size argument.

With format utf8, qmp_memchar_write() copies size bytes from data,
happily reading beyond data.  Copies crap from the heap or even
crashes.

Drop the size parameter, and always copy the full data argument.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2013-02-06 16:35:17 -06:00
Orit Wasserman
dbca1b3773 Fix example for query-migrate-capabilities
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>

Signed-off-by: Juan Quintela <quintela@redhat.com>
2013-02-01 08:32:21 +01:00
Michal Privoznik
99f4280854 qmp-commands.hx: s/tray-open/tray_open/ to match qapi schema
Currently, we are using 'tray_open' in QMP and 'tray-open' in
HMP. However, the QMP documentation was mistakenly using the
HMP version.

Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2013-01-30 11:19:53 +01:00
Anthony Liguori
503cb22e05 Merge remote-tracking branch 'kwolf/for-anthony' into staging
# By Paolo Bonzini (14) and others
# Via Kevin Wolf
* kwolf/for-anthony: (24 commits)
  ide: Add fall through annotations
  block: Create proper size file for disk mirror
  ahci: Add migration support
  ahci: Change data types in preparation for migration
  ahci: Remove unused AHCIDevice fields
  hbitmap: add assertion on hbitmap_iter_init
  mirror: do nothing on zero-sized disk
  block/vdi: Check for bad signature
  block/vdi: Improved return values from vdi_open
  block/vdi: Improve debug output for signature
  block: Use error code EMEDIUMTYPE for wrong format in some block drivers
  block: Add special error code for wrong format
  mirror: support arbitrarily-sized iterations
  mirror: support more than one in-flight AIO operation
  mirror: add buf-size argument to drive-mirror
  mirror: switch mirror_iteration to AIO
  mirror: allow customizing the granularity
  block: allow customizing the granularity of the dirty bitmap
  block: return count of dirty sectors, not chunks
  mirror: perform COW if the cluster size is bigger than the granularity
  ...
2013-01-28 14:46:45 -06:00
Paolo Bonzini
08e4ed6cde mirror: add buf-size argument to drive-mirror
This makes sense when the next commit starts using the extra buffer space
to perform many I/O operations asynchronously.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-01-25 18:18:34 +01:00
Paolo Bonzini
eee13dfe30 mirror: allow customizing the granularity
The desired granularity may be very different depending on the kind of
operation (e.g. continuous replication vs. collapse-to-raw) and whether
the VM is expected to perform lots of I/O while mirroring is in progress.

Allow the user to customize it, while providing a sane default so that
in general there will be no extra allocated space in the target compared
to the source.

Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2013-01-25 18:18:34 +01:00
Lei Li
49b6d7220b QAPI: Introduce memchar-read QMP command
Signed-off-by: Lei Li <lilei@linux.vnet.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-01-25 11:46:50 -02:00
Lei Li
1f590cf945 QAPI: Introduce memchar-write QMP command
Signed-off-by: Lei Li <lilei@linux.vnet.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2013-01-25 11:23:06 -02:00
Luiz Capitulino
01ceb97e7b balloon: drop old stats code & API
Next commit will re-enable balloon stats with a different interface, but
this old code conflicts with it. Let's drop it.

It's important to note that the QMP and HMP interfaces are also dropped
by this commit. That shouldn't be a problem though, because:

 1. All QMP fields are optional
 2. This feature has always been disabled

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2013-01-25 10:36:54 -02:00
Gerd Hoffmann
0a1a7fabda chardev: add pty chardev support to chardev-add (qmp)
The ptsname is returned directly, so there is no need to
use query-chardev to figure the pty device path.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2013-01-16 06:58:54 +01:00
Gerd Hoffmann
ffbdbe59ac chardev: add file chardev support to chardev-add (qmp)
Add support for file chardevs.  Output file is mandatory,
input file is optional.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2013-01-16 06:58:54 +01:00
Gerd Hoffmann
f1a1a35638 chardev: add qmp hotplug commands, with null chardev support
Add chardev-add and chardev-remove qmp commands.  Hotplugging
a null chardev is supported for now, more will be added later.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2013-01-16 06:58:54 +01:00
Anthony Liguori
90c45b3031 Merge remote-tracking branch 'kwolf/for-anthony' into staging
* kwolf/for-anthony: (32 commits)
  osdep: Less restrictive F_SEFL in qemu_dup_flags()
  qemu-iotests: add testcases for mirroring on-source-error/on-target-error
  qmp: add pull_event function
  mirror: add support for on-source-error/on-target-error
  iostatus: forward block_job_iostatus_reset to block job
  qemu-iotests: add mirroring test case
  mirror: implement completion
  qmp: add drive-mirror command
  mirror: introduce mirror job
  block: introduce BLOCK_JOB_READY event
  block: add block-job-complete
  block: rename block_job_complete to block_job_completed
  block: export dirty bitmap information in query-block
  block: introduce new dirty bitmap functionality
  block: add bdrv_open_backing_file
  block: add bdrv_query_stats
  block: add bdrv_query_info
  qemu-config: Add new -add-fd command line option
  monitor: Prevent removing fd from set during init
  monitor: Enable adding an inherited fd to an fd set
  ...

Conflicts:
	vl.c

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2012-10-29 10:34:05 -05:00
Paolo Bonzini
b952b5589a mirror: add support for on-source-error/on-target-error
Error management is important for mirroring; otherwise, an error on the
target (even something as "innocent" as ENOSPC) requires to start again
with a full copy.  Similar to on_read_error/on_write_error, two separate
knobs are provided for on_source_error (reads) and on_target_error (writes).
The default is 'report' for both.

The 'ignore' policy will leave the sector dirty, so that it will be
retried later.  Thus, it will not cause corruption.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-10-24 10:26:22 +02:00
Paolo Bonzini
d9b902db3f qmp: add drive-mirror command
This adds the monitor commands that start the mirroring job.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-10-24 10:26:20 +02:00
Paolo Bonzini
aeae883baf block: add block-job-complete
While streaming can be dropped as soon as it progressed through the whole
image, mirroring needs to be completed manually for two reasons: 1) so that
management knows exactly when the VM switches to the target; 2) because
for other use cases such as replication, we may leave the operation running
for the whole life of the virtual machine.

Add a new block job command that manually completes background operations.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-10-24 10:26:19 +02:00
Paolo Bonzini
6dd844db4a qmp: add NBD server commands
Adding an NBD server inside QEMU is trivial, since all the logic is
in nbd.c and can be shared easily between qemu-nbd and QEMU itself.
The main difference is that qemu-nbd serves a single unnamed export,
while QEMU serves named exports.

Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2012-10-23 22:39:33 +02:00
Juan Quintela
2c52ddf1cb migration: print expected downtime in info migrate
Signed-off-by: Juan Quintela <quintela@redhat.com>
2012-10-17 18:34:58 +02:00
Juan Quintela
9c5a9fcf53 migration: print total downtime for final phase of migration
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
2012-10-17 18:34:58 +02:00
Anthony Liguori
a14c74928b Merge remote-tracking branch 'sstabellini/xen-2012-10-03' into staging
* sstabellini/xen-2012-10-03:
  xen: Set the vram dirty when an error occur.
  exec, memory: Call to xen_modified_memory.
  exec: Introduce helper to set dirty flags.
  xen: Introduce xen_modified_memory.
  QMP, Introduce xen-set-global-dirty-log command.
  qemu/xen: Add 64 bits big bar support on qemu
  xen: Fix, no unplug of pt device by platform device.
2012-10-04 19:56:26 -05:00
Anthony Liguori
05d4f2f2ca Merge remote-tracking branch 'kwolf/for-anthony' into staging
* kwolf/for-anthony: (30 commits)
  qemu-iotests: add tests for streaming error handling
  qemu-iotests: map underscore to dash in QMP argument names
  blkdebug: process all set_state rules in the old state
  stream: add on-error argument
  block: introduce block job error
  iostatus: reorganize io error code
  iostatus: change is_read to a bool
  iostatus: move BlockdevOnError declaration to QAPI
  iostatus: rename BlockErrorAction, BlockQMPEventAction
  qemu-iotests: add test for pausing a streaming operation
  qmp: add block-job-pause and block-job-resume
  block: add support for job pause/resume
  qmp: add 'busy' member to BlockJobInfo
  block: add block_job_query
  block: move job APIs to separate files
  block: fix documentation of block_job_cancel_sync
  qerror/block: introduce QERR_BLOCK_JOB_NOT_ACTIVE
  qemu-iotests: add initial tests for live block commit
  QAPI: add command for live block commit, 'block-commit'
  block: helper function, to find the base image of a chain
  ...
2012-10-04 19:53:50 -05:00
Anthony PERARD
39f42439d0 QMP, Introduce xen-set-global-dirty-log command.
This command is used during a migration of a guest under Xen. It calls
memory_global_dirty_log_start or memory_global_dirty_log_stop according to the
argument pass to the command.

Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-10-03 13:48:19 +00:00
Paolo Bonzini
1d809098aa stream: add on-error argument
This patch adds support for error management to streaming.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-09-28 19:40:56 +02:00
Paolo Bonzini
6e37fb811a qmp: add block-job-pause and block-job-resume
Add QMP commands matching the functionality.

Paused jobs cannot be canceled without first resuming them.  This
ensures that I/O errors are never missed by management.  However, an
optional force argument can be specified to allow that.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-09-28 19:14:32 +02:00
Jeff Cody
ed61fc10e8 QAPI: add command for live block commit, 'block-commit'
The command for live block commit is added, which has the following
arguments:

device: the block device to perform the commit on (mandatory)
base:   the base image to commit into; optional (if not specified,
        it is the underlying original image)
top:    the top image of the commit - all data from inside top down
        to base will be committed into base (mandatory for now; see
        note, below)

speed:  maximum speed, in bytes/sec

Note: Eventually this command will support merging down the active layer,
      but that code is not yet complete.  If the active layer is passed
      in as top, then an error will be returned.  Once merging down the
      active layer is supported, the 'top' argument may become optional,
      and default to the active layer.

The is done as a block job, so upon completion a BLOCK_JOB_COMPLETED will
be emitted.

Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-09-28 18:23:47 +02:00
Luiz Capitulino
b224e5e216 qapi: convert add_client
Also fixes a few issues while there:

 1. The fd returned by monitor_get_fd() leaks in most error conditions
 2. monitor_get_fd() return value is not checked. Best case we get
    an error that is not correctly reported, worse case one of the
    functions using the fd (with value of -1) will explode
 3. A few error conditions aren't reported
 4. We now "use up" @fdname always.  Before, it was left alone for
    invalid @protocol

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
2012-09-26 12:42:19 -03:00
Luiz Capitulino
ad39cf6d15 qapi: convert screendump
Next commits will update devices to propagate errors.

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-09-05 15:48:57 -03:00
Amos Kong
e4c8f004c5 qapi: convert sendkey
Convert 'sendkey' to use QAPI.

QAPI passes key's index of mapping table to qmp_send_key(),
not keycode. So we use help functions to convert key/code to
index of key_defs, and 'index' will be converted to 'keycode'
inside qmp_send_key().

For qmp, QAPI would check invalid key and raise error.
For hmp, invalid key is checked in hmp_send_key().

'send-key' of QMP doesn't support key in hexadecimal format.

Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-09-05 15:48:57 -03:00
Anthony Liguori
86759aa89d Merge remote-tracking branch 'qmp/queue/qmp' into staging
* qmp/queue/qmp:
  migration: move total_time from ram stats to migration info
  monitor: avoid declaring unused variables
  qapi: Fix memory leak
2012-08-22 13:33:15 -05:00
Daniel P. Berrange
99afc91d6c qapi: add 'query-target' command to return target arch
Add a 'query-target' QAPI command to allow management applications
to determine what target architecture a QEMU binary is emulating
without having to parse the binary name or -help output

  $ qmp-shell -p /tmp/qemu
  (QEMU) query-target
  {   u'return': {   u'arch': u'x86_64' }}

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2012-08-22 10:47:17 -05:00
Juan Quintela
7aa939af39 migration: move total_time from ram stats to migration info
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-08-21 15:06:24 -03:00
Corey Bryant
ba1c048a8f qapi: Introduce add-fd, remove-fd, query-fdsets
This patch adds support that enables passing of file descriptors
to the QEMU monitor where they will be stored in specified file
descriptor sets.

A file descriptor set can be used by a client like libvirt to
store file descriptors for the same file.  This allows the
client to open a file with different access modes (O_RDWR,
O_WRONLY, O_RDONLY) and add/remove the passed fds to/from an fd
set as needed.  This will allow QEMU to (in a later patch in this
series) "open" and "reopen" the same file by dup()ing the fd in
the fd set that corresponds to the file, where the fd has the
matching access mode flag that QEMU requests.

The new QMP commands are:
  add-fd: Add a file descriptor to an fd set
  remove-fd: Remove a file descriptor from an fd set
  query-fdsets: Return information describing all fd sets

Note: These commands are not compatible with the existing getfd
and closefd QMP commands.

Signed-off-by: Corey Bryant <coreyb@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-08-15 10:48:57 +02:00
Anthony Liguori
633decd711 Merge remote-tracking branch 'qmp/queue/qmp' into staging
* qmp/queue/qmp: (48 commits)
  target-ppc: add implementation of query-cpu-definitions (v2)
  target-i386: add implementation of query-cpu-definitions (v2)
  qapi: add query-cpu-definitions command (v2)
  compiler: add macro for GCC weak symbols
  qapi: add query-machines command
  qapi: mark QOM commands stable
  qmp: introduce device-list-properties command
  qmp: add SUSPEND_DISK event
  qmp: qmp-events.txt: add missing doc for the SUSPEND event
  qmp: qmp-events.txt: put events in alphabetical order
  qmp: emit the WAKEUP event when the guest is put to run
  qmp: don't emit the RESET event on wakeup from S3
  scripts: qapi-commands.py: qmp-commands.h: include qdict.h
  docs: writing-qmp-commands.txt: update error section
  error, qerror: drop QDict member
  qerror: drop qerror_table and qerror_format()
  error, qerror: pass desc string to error calls
  error: drop error_get_qobject()/error_set_qobject()
  qemu-ga: switch to the new error format on the wire
  qmp: switch to the new error format on the wire
  ...
2012-08-13 16:12:35 -05:00
Anthony Liguori
e4e31c6324 qapi: add query-cpu-definitions command (v2)
This command attempts to map to the behavior of -cpu ?.  Unfortunately, the
output of this command differs wildly across targets.

To accommodate this, we use a weak symbol to implement a default version of the
command that fails with a QERR_NOT_SUPPORTED error code.  Targets can then
override and implement this command if it makes sense for them.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-08-13 16:10:18 -03:00
Anthony Liguori
01d3c80d68 qapi: add query-machines command
This provides the same output as -M ? but in a structured way.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-08-13 16:10:18 -03:00
Anthony Liguori
1daa31b9db qmp: introduce device-list-properties command
This can be used in conjunction with qom-list-types to determine the supported
set of devices and their parameters.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-08-13 16:10:18 -03:00
Luiz Capitulino
de253f1491 qmp: switch to the new error format on the wire
IMPORTANT: this BREAKS QMP's compatibility for the error response.

This commit changes QMP's wire protocol to make use of the simpler
error format introduced by previous commits.

There are two important (and mostly incompatible) changes:

 1. Almost all error classes have been replaced by GenericError. The
    only classes that are still supported for compatibility with
    libvirt are: CommandNotFound, DeviceNotActive, KVMMissingCap,
    DeviceNotFound and MigrationExpected

 2. The 'data' field of the error dictionary is gone

As an example, an error response like:

  { "error": { "class": "DeviceNotRemovable",
               "data": { "device": "virtio0" },
               "desc": "Device 'virtio0' is not removable" } }

Will now be emitted as:

  { "error": { "class": "GenericError",
               "desc": "Device 'virtio0' is not removable" } }

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
2012-08-13 14:17:53 -03:00
Orit Wasserman
f36d55af74 Add XBZRLE statistics
Signed-off-by: Benoit Hudzia <benoit.hudzia@sap.com>
Signed-off-by: Petter Svard <petters@cs.umu.se>
Signed-off-by: Aidan Shribman <aidan.shribman@sap.com>
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:12 +02:00
Orit Wasserman
004d4c10ae Add migration accounting for normal and duplicate pages
Signed-off-by: Benoit Hudzia <benoit.hudzia@sap.com>
Signed-off-by: Petter Svard <petters@cs.umu.se>
Signed-off-by: Aidan Shribman <aidan.shribman@sap.com>
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:12 +02:00
Orit Wasserman
62d4e3fe31 Change total_time to total-time in MigrationStats
migration total_time was introduced in commit
d5f8a5701d for QEMU 1.2

Signed-off-by: Orit Wasserman <owasserm@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:12 +02:00
Orit Wasserman
9e1ba4cc4e Add migrate_set_cache_size command
Change XBZRLE cache size in bytes (the size should be a power of 2, it will be
rounded down to the nearest power of 2).
If XBZRLE cache size is too small there will be many cache miss.

New query-migrate-cache-size QMP command and 'info migrate_cache_size' HMP
command to query cache value.

Signed-off-by: Benoit Hudzia <benoit.hudzia@sap.com>
Signed-off-by: Petter Svard <petters@cs.umu.se>
Signed-off-by: Aidan Shribman <aidan.shribman@sap.com>
Signed-off-by: Orit Wasserman <owasserm@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:12 +02:00
Orit Wasserman
0045843324 Add migrate-set-capabilities
The management can enable/disable a capability for the next migration by using
migrate-set-capabilities QMP command.
The user can use migrate_set_capability HMP command.

Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:11 +02:00
Orit Wasserman
bbf6da32b5 Add migration capabilities
The management can query the current migration capabilities using
query-migrate-capabilities QMP command.
The user can use 'info migrate_capabilities' HMP command.
Currently only XBZRLE capability is available.

Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
2012-08-08 13:51:11 +02:00
Benoît Canet
2e3e331710 block: Use bdrv_get_backing_file_depth()
Use the dedicated counting function in qmp_query_block in order to
propagate the backing file depth to HMP and add backing_file_depth
to qmp-commands.hx

Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-08-03 10:10:51 -03:00
Corey Bryant
208c9d1b7c qapi: Convert getfd and closefd
Signed-off-by: Corey Bryant <coreyb@linux.vnet.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-07-13 13:46:55 -03:00
Daniel P. Berrange
4860853d60 Add 'query-events' command to QMP to query async events
Sometimes it is neccessary for an application to determine
whether a particular QMP event is available, so they can
decide whether to use compatibility code instead. This
introduces a new 'query-events' command to QMP to do just
that

 { "execute": "query-events" }
 {"return": [{"name": "WAKEUP"},
             {"name": "SUSPEND"},
             {"name": "DEVICE_TRAY_MOVED"},
             {"name": "BLOCK_JOB_CANCELLED"},
             {"name": "BLOCK_JOB_COMPLETED"},
             ...snip...
             {"name": "SHUTDOWN"}]}

* monitor.c: Turn MonitorEvent -> string conversion
  into a lookup from a static table of constant strings.
  Add impl of qmp_query_events monitor command handler
* qapi-schema.json, qmp-commands.hx: Define contract of
  query-events command

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-06-04 13:49:35 -03:00
Luiz Capitulino
5f96415527 qapi: convert netdev_del
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
2012-06-04 13:49:35 -03:00
Luiz Capitulino
928059a37b qapi: convert netdev_add
This is not a full QAPI conversion, but an intermediate step.

In essence, do_netdev_add() is split into three functions:

 1. netdev_add(): performs the actual work. This function is fully
    converted to Error (thus, it's "qapi-friendly")

 2. qmp_netdev_add(): the QMP front-end for netdev_add(). This is
    coded by hand and not auto-generated (gen=no in the schema). The
    reason for this it's a lot easier and simpler to with QemuOpts
    this way

 3. hmp_netdev_add(): HMP front-end.

This design was suggested by Paolo Bonzini.

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
2012-06-04 13:49:35 -03:00
Wen Congyang
783e9b4826 introduce a new monitor command 'dump-guest-memory' to dump guest's memory
The command's usage:
   dump-guest-memory [-p] protocol [begin] [length]
The supported protocol can be file or fd:
1. file: the protocol starts with "file:", and the following string is
   the file's path.
2. fd: the protocol starts with "fd:", and the following string is the
   fd's name.

Note:
  1. If you want to use gdb to process the core, please specify -p option.
     The reason why the -p option is not default is:
       a. guest machine in a catastrophic state can have corrupted memory,
          which we cannot trust.
       b. The guest machine can be in read-mode even if paging is enabled.
          For example: the guest machine uses ACPI to sleep, and ACPI sleep
          state goes in real-mode.
  2. If you don't want to dump all guest's memory, please specify the start
     physical address and the length.

Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-06-04 13:49:34 -03:00
Paolo Bonzini
31155b9b3c block: add mode argument to blockdev-snapshot-sync
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-05-10 10:32:11 +02:00
Stefan Hajnoczi
c83c66c3b5 block: add 'speed' optional parameter to block-stream
Allow streaming operations to be started with an initial speed limit.
This eliminates the window of time between starting streaming and
issuing block-job-set-speed.  Users should use the new optional 'speed'
parameter instead so that speed limits are in effect immediately when
the job starts.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-04-27 11:44:50 -03:00
Stefan Hajnoczi
882ec7ce53 block: change block-job-set-speed argument from 'value' to 'speed'
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-04-27 11:44:50 -03:00
Stefan Hajnoczi
db58f9c060 qmp: make block job command naming consistent
The block streaming and job commands used '_' instead of '-' for reasons
of compatibility with libvirt, which already included support for the
'_' naming.  However, the semantics of block_job_cancel have changed and
libvirt now needs to handle the new semantics.

Since the old semantics were never in a QEMU release we can still rename
the commands to use '-' instead of '_'.  Libvirt is also happy because
the new name can be used to distinguish QEMU binaries that support the
latest block-job-cancel semantics from those that include a downstream
block_job_cancel command.

Therefore, let's apply the QAPI/QMP naming rules to the block streaming
and job commands.  QEMU 1.1 will be the first release with these
commands so no upstream users can break.

Note that HMP commands are left with '_' because that is the convention
there.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-04-23 13:02:01 -03:00
Luiz Capitulino
a15fef21c7 qapi: convert device_del
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
2012-04-09 14:35:25 -03:00
Paolo Bonzini
b9f8978cc4 qmp: add and use q type specifier
"O" is being used by the transaction and qom-set commands to mean "any
QObject", but it really means "do not validate the argument list".
Add a new specifier with the correct meaning.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-03-27 09:15:28 -03:00
Anthony Liguori
33cf629a37 Merge remote-tracking branch 'sstabellini/saverestore-8' into staging
* sstabellini/saverestore-8:
  xen: do not allocate RAM during INMIGRATE runstate
  xen mapcache: check if memory region has moved.
  xen: record physmap changes to xenstore
  Set runstate to INMIGRATE earlier
  Introduce "xen-save-devices-state"
  cirrus_vga: do not reset videoram

Conflicts:
	qapi-schema.json

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2012-03-19 13:39:42 -05:00
Stefano Stabellini
a7ae8355b4 Introduce "xen-save-devices-state"
- add an "is_ram" flag to SaveStateEntry;

- register_savevm_live sets is_ram for live_savevm devices;

- introduce a "xen-save-devices-state" QAPI command that can be used to save
the state of all devices, but not the RAM or the block devices of the
VM.

Changes in v8:

- rename save-devices-state to xen-save-devices-state.

Changes in v7:

- rename save_devices to save-devices-state.

Changes in v6:

- remove the is_ram parameter from register_savevm_live and sets is_ram
if the device is a live_savevm device;

- introduce save_devices as a QAPI command, write a better description
for it;

- fix CODING_STYLE;

- introduce a new doc to explain the save format used by save_devices.

Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-03-19 18:21:00 +00:00
Luiz Capitulino
e1c37d0e94 qapi: Convert migrate
The migrate command is one of those commands where HMP and QMP completely
mix up together. This made the conversion to the QAPI (which separates the
command into QMP and HMP parts) a bit difficult.

The first important change to be noticed is that this commit completes the
removal of the Monitor object from migration code, started by the previous
commit.

Another important and tricky change is about supporting the non-detached
mode. That is, if the user doesn't pass '-d' the migrate command will lock
the monitor and will only release it when migration is finished.

To support this in the new HMP command (hmp_migrate()), it is necessary
to create a timer which runs every second and checks if the migration is
still active. If it is, the timer callback will re-schedule itself to run
one second in the future. If the migration has already finished, the
monitor lock is released and the user can use it normally.

All these changes should be transparent to the user.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-03-15 10:39:52 -03:00
Paolo Bonzini
6cc2a4157b qmp: convert blockdev-snapshot-sync to a wrapper around transactions
Simplify the blockdev-snapshot-sync code and gain failsafe operation
by turning it into a wrapper around the new transaction command.  A new
option is also added matching "mode".

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-03-12 15:14:07 +01:00
Paolo Bonzini
bc8b094feb add mode field to blockdev-snapshot-sync transaction item
The mode field lets a management application create the snapshot
destination outside QEMU.

Right now, the only modes are "existing" and "absolute-paths".  Mirroring
introduces "no-backing-file".  In the future "relative-paths" could be
implemented too.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-03-12 15:14:07 +01:00
Paolo Bonzini
52e7c241ac rename blockdev-group-snapshot-sync
We will add other kinds of operation.  Prepare for this by adjusting
the schema.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-03-12 15:14:07 +01:00
Jeff Cody
c186402c44 QMP: Add qmp command for blockdev-group-snapshot-sync
This adds the QMP command for blockdev-group-snapshot-sync. It
takes an array in as the input, for the argument devlist.  The
array consists of the following elements:

    + device:        device to snapshot. e.g. "ide-hd0", "virtio0"
    + snapshot-file: path & file for the snapshot image. e.g. "/tmp/file.img"
    + format:        snapshot format. e.g., "qcow2". Optional

There is no HMP equivalent for the command.

Signed-off-by: Jeff Cody <jcody@redhat.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-02-29 15:48:39 +01:00
Gerd Hoffmann
9b9df25a47 suspend: add system_wakeup monitor command
This patch adds the system_wakeup monitor command which will simply
wake up suspended guests.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2012-02-24 13:36:03 -06:00
Daniel P. Berrange
f1f5f4070c Add SPICE support to add_client monitor command
With the acceptance of some new APIs to libspice-server.so it
is possible to add support for SPICE to the 'add_client'
monitor command, bringing parity with VNC. Since SPICE can
use TLS or plain connections, the command also gains a new
'tls' parameter to specify whether TLS should be attempted
on the injected client sockets.

This new feature is only enabled if building against a
libspice-server >= 0.10.1

* qmp-commands.hx: Add 'tls' parameter & missing doc for
  'skipauth' parameter
* monitor.c: Wire up SPICE for 'add_client' command
* ui/qemu-spice.h, ui/spice-core.c: Add qemu_spice_display_add_client
  API to wire up from monitor

[1] http://cgit.freedesktop.org/spice/spice/commit/server/spice.h?id=d55b68b6b44f2499278fa860fb47ff22f5011faa
    http://cgit.freedesktop.org/spice/spice/commit/server/spice.h?id=bd07dde530d9504e1cfe7ed5837fc00c26f36716

Changes in v3:
 - Added 'optional' flag to new parameters documented
 - Added no-op impl of qemu_spice_display_add_client when
   SPICE is disabled during build

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2012-02-21 10:36:05 +01:00
Anthony Liguori
5eeee3fa2e qom: add new command to search for types
This adds a command that allows searching for types that implement a property.
This allows you to do things like search for all available PCIDevices.  In the
future, we'll also have a standard interface for things with a BlockDriverState
property that a PCIDevice could implement.

This will enable search queries like, "any type that implements the BlockDevice
interface" which would allow management tools to present available block devices
without having to hard code device names.  Since an object can implement
multiple interfaces, one device could act both as a BlockDevice and a
NetworkDevice.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2012-02-03 10:41:07 -06:00
Stefan Hajnoczi
fb5458cd10 qmp: add query-block-jobs
Add query-block-jobs, which shows the progress of ongoing block device
operations.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-01-26 14:49:18 +01:00
Stefan Hajnoczi
370521a1d6 qmp: add block_job_cancel command
Add block_job_cancel, which stops an active block streaming operation.
When the operation has been cancelled the new BLOCK_JOB_CANCELLED event
is emitted.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-01-26 14:49:18 +01:00
Stefan Hajnoczi
2d47c6e9aa qmp: add block_job_set_speed command
Add block_job_set_speed, which sets the maximum speed for a background
block operation.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-01-26 14:49:17 +01:00
Stefan Hajnoczi
12bd451fe0 qmp: add block_stream command
Add the block_stream command, which starts copy backing file contents
into the image file.  Also add the BLOCK_JOB_COMPLETED QMP event which
is emitted when image streaming completes.  Later patches add control
over the background copy speed, cancelation, and querying running
streaming operations.

Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2012-01-26 14:49:14 +01:00
Luiz Capitulino
80047da59b qapi: Convert block_set_io_throttle
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:39 -02:00
Luiz Capitulino
333a96ec9f qapi: Convert change
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:39 -02:00
Luiz Capitulino
270b243f91 qapi: Introduce change-vnc-password
New QMP command to change the VNC password.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:39 -02:00
Luiz Capitulino
c245b6a37d qapi: Convert eject
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:39 -02:00
Luiz Capitulino
9ad5372daa qapi: Convert expire_password
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:38 -02:00
Luiz Capitulino
fbf796fd6f qapi: Convert set_password
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2012-01-18 10:23:38 -02:00
Anthony Liguori
eb6e8ea5c3 qom: qom_{get, set} monitor commands (v2)
This allows clients to read and write device model properties through QMP.  QAPI
doesn't support Visitor types yet and these commands are special in that they
don't work with fixed types.

I've added a documentation stub to qapi-schema.json so we can keep consistency
there.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-12-15 09:20:48 -06:00
Anthony Liguori
b4b12c6247 qmp: add qom-list command
This can be used to list properties in the device model.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2011-12-15 09:20:48 -06:00
Luiz Capitulino
3dc853832d qapi: Convert migrate_set_speed
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
4f0a993bf3 qapi: Convert migrate_set_downtime
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
6cdedb075f qapi: Convert migrate_cancel
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
d51a67b4d3 qapi: Convert human-monitor-command
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
6106e2492f qapi: Convert blockdev_snapshot_sync
Unfortunately, this conversion required an additional change.

In the old QMP command, the 'snapshot-file' argument is specified as
optional. The idea is to take the snapshot internally if 'snapshot-file'
is not passed. However, internal snapshots are not supported yet so
the command returns a MissingParamater error if 'snapshot-file' is not
passed. Which makes the argument actually required and will cause
compatibility breakage if we change that in the future.

To fix this the QAPI converted blockdev_snapshot_sync command makes the
'snapshot-file' argument required. Again, in practice it's actually required,
so this is not incompatible.

If we do implement internal snapshots someday, we'll need a new argument
for it.

Note that this discussion doesn't affect HMP.

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
5e7caacb25 qapi: Convert block_resize
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
d72f326431 qapi: Convert balloon
Note that the command being dropped uses the deprecated MONITOR_CMD_ASYNC
API, but the new command is a regular synchronous command. There shouldn't
be visible differences though, as MONITOR_CMD_ASYNC is internal only.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
a4dea8a9f4 qapi: Convert block_passwd
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
4b37156c40 qapi: Convert set_link
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
ab49ab5c48 qapi: Convert inject-nmi
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
e42e818bf4 qapi: Convert cont
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
6d3962bf84 qapi: Convert pmemsave
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:01 -02:00
Luiz Capitulino
0cfd6a9ab4 qapi: Convert memsave
Please, note that the QMP command has a new 'cpu-index' parameter.

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:00 -02:00
Luiz Capitulino
22e1bb9c15 qapi: Complete system_powerdown conversion
Commit 5bc465e4b1 converted only
the HMP part of the system_powerdown command to the QAPI, this
commit completes it by converting the QMP part too.

Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-12-06 11:40:00 -02:00
Zhi Yong Wu
727f005e6a hmp/qmp: add block_set_io_throttle
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2011-12-05 14:51:35 +01:00
Anthony Liguori
96b3d73f5a Merge remote-tracking branch 'qmp/queue/qmp' into staging
Conflicts:
	ui/spice-core.c
2011-10-31 11:02:29 -05:00
Luiz Capitulino
79627472db qapi: Convert query-pci
This also fixes a bug with the old version: QMP would invert device id
and vendor id. This would look ok on HMP because it was printing
"device:vendor" instead of "vendor:device".

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
96637bcdf9 qapi: Convert query-balloon
Please, note that some of the code supporting memory statistics is
still around (eg. virtio_balloon_receive_stats() and reset_stats()).

Also, the qmp_query_balloon() function is synchronous and thus doesn't
make any use of the (not fully working) monitor's asynchronous command
support (the old non-qapi implementation did).

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
d1f29646f2 qapi: Convert query-spice
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
2b54aa879e qapi: Convert query-vnc
There are three important remarks in relation to the non-qapi command:

 1. This commit also fixes the behavior of the 'query-vnc' and 'info vnc'
    commands to return an error when qemu is built without VNC support
    (ie. --disable-vnc). The non-qapi command would return the OK
    response in QMP and no response in HMP

 2. The qapi version explicitly marks the fields 'host', 'family',
    'service' and 'auth' as optional. Their are not documented as optional
    in the non-qapi command doc, but they would not be returned if
    vnc support is disabled. The qapi version maintains the same
    semantics, but documents those fields correctly

 3. The 'clients' field, which is a list, is marked as optional but is
    always returned. If there are no clients connected an empty list
    is returned. This is not the Right Way to this in the qapi but it's
    how the non-qapi command used to work

Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
f11f57e405 qapi: Convert query-blockstats
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
b202381800 qapi: Convert query-block
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
de0b36b67e qapi: Convert query-cpus
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:47 -02:00
Luiz Capitulino
755f196898 qapi: Convert the cpu command
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:46 -02:00
Luiz Capitulino
791e7c820e qapi: Convert query-migrate
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
2011-10-27 11:48:46 -02:00