Instantiate the three PL061 GPIO modules the realview boards have.
Connect the MMC card status outputs of the PL181 MMC controller
to both the system registers and the GPIO module which handles
internal devices.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a qemu_irq_split() function which allows a board to wire a single
GPIO output up to two GPIO inputs. This is needed for realview boards,
where the MMC card status is visible both in a system register and
via a PL061 GPIO module.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
ARM's PL061 has a different set of ID registers to the one in the
Luminary Stellaris; implement this so that the Linux driver can
identify the Realview PBX PL061 correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implement some GPIO inputs which a board can connect up to set the
MMC card status bits in the MCI register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add two GPIO output pins to the PL181 model to indicate the card
present and readonly status information. On ARM boards these usually
are reflected in a system register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Update not only dbc but also dnad when skipping bytes during the MSGOUT
phase. Previously only dbc was updated which is probably wrong and
could lead to bogus message codes being read.
Tested on Linux and Windows Server 2003.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
bugfix under DOS for AMD netware driver:
AMD PCNTNW Ethernet MLID v3.10 (960115), network card not found
bugfix works well under DOS with:
1.) AMD NDIS driver v2.0.1
2.) AMD PCNTNW Ethernet MLID v3.10 (960115)
3.) Knoppix 6.2
Signed-off-by: Gerhard Wiesinger <lists@wiesinger.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
A pointer to a size_t variable was passed as the void * pointer to
lduw_p() in virtio_net_receive(). Instead of acting on the 16-bit value
this caused failure on big-endian hosts.
Avoid this issue in the future by using stw_p() instead. In general we
should use ld*_p() for loading from target memory and st*_p() for
storing to target memory anyway, not the other way around.
Also tighten up a correct use of lduw_p() when stw_p() should be used
instead in virtio_net_get_config().
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
VMSTATE_PCIE_AER_ERRS is indeed useful for other emulation drivers.
Move it to hw/hw.h under the name of VMSTATE_STRUCT_VARRAY_POINTER_UINT16.
Also add VMSTATE_STRUCT_VARRAY_POINTER_INT32 which is more or less
the same as _UINT16 macro, except the fact it uses int32_t internally.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
It should be PXA2xxTimerInfo, not pxa2xx_timer_info. Replace all
occurences of old name with the new one.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This is a _TEST variant of VMSTATE_STRUCT_ARRAY, necessary e.g.
for future patch changing pxa2xx_timer to use vmstate.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Use qdev/sysbus framework to handle pxa2xx-pic. Instead of exposing IRQs
via array, reference them via qdev_get_gpio_in().
Patch has been modified by the committer.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Final corrections for IRQ levels that are set by mst_fpga:
* Don't retranslate IRQ if previously IRQ was masked.
* After setting or clearing IRQs through register, apply mask
before setting parent IRQ level.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
VirtIOSerialDevice is like VirtIOSerialPort with just the first two
fields, which makes it pretty pointless. Using VirtIOSerialPort
directly works equally well and is less confusing.
[Amit: - rebase
- rename 'dev' to 'port' in function params in virtio-serial.h ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The SD_STATUS and SEND_NUM_WR_BLOCKS commands are supposed to cause
the card to send data back to the host. However sd.c was missing the
state change to sd_sendingdata_state for these commands, with the effect
that the Linux driver would either hang indefinitely waiting for
nonexistent data (pl181) or read zeroes and provoke a qemu warning
message (omap).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Remove the typedef SetIRQFunc, as it is not used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Nothing prevented IRQ sharing on the ISA bus in principle. Not all
boards supported this, neither each and every card nor driver and OS.
Still, there existed valid IRQ sharing scenarios, (at least) two of them
can also be found in QEMU: >2 PC UARTs and the PREP IDE buses.
So remove this artificial restriction from our ISA model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The following patch adds PS/2 keyboard Scancode Set 3 support.
Signed-off-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
RST bit is (1 << 4) bit, not (1 << 3), fix condition
that enables i2s if ENB is set and RST is not set.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add handling of 0xe0xx keycodes to pxa2xx_driver.
Extended keycodes in keymap should be marked with most significant
bit set (i.e. 0x80). Without this patch it's not possible to handle
i.e. cursor keys.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add emulation of KPAS register and proper emulation of
KPASMKP regs, so now driver supports multipresses and properly
works with Linux driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
qemu makes it possible to disable link at tap which is not communicated
to the guest but causes all packets to be dropped.
When vhost-net is enabled, vhost needs to be aware of both the virtio
link_down and the peer link_down. we switch to userspace emulation when
either is down.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: pradeep <psuriset@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The spec says: Any descriptor with a non-zero status byte has been
processed by the hardware, and is ready to be handled by the software.
Thus, once we change a descriptor status to non-zero we should
never move the head backwards and try to reuse this
descriptor from hardware.
This actually happened with a multibuffer packet
that arrives when we don't have enough buffers.
Fix by checking that we have enough buffers upfront
so we never need to discard the packet midway through.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The e1000 spec says: if software statically allocates
buffers, and uses memory read to check for completed descriptors, it
simply has to zero the status byte in the descriptor to make it ready
for reuse by hardware. This is not a hardware requirement (moving the
hardware tail pointer is), but is necessary for performing an in–memory
scan.
Thus the guest does not have to clear the status byte. In case it
doesn't we need to clear EOP for all descriptors
except the last. While I don't know of any such guests,
it's probably a good idea to stick to the spec.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
e1000 supports multi-buffer packets larger than rxbuf_size.
This fixes the following (on linux):
- in guest: ifconfig eth1 mtu 16110
- in host: ifconfig tap0 mtu 16110
ping -s 16082 <guest-ip>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Turn fdc_init_isa into an inline function.
Get floppy geometry directly from the drives.
Don't expose FDCtrl.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Other geometry guessing functions already reside in block.c.
Remove some unused or debugging only fields.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
