FEAT_PMUv3p5 introduces new bits which disable the cycle
counter from counting:
* MDCR_EL2.HCCD disables the counter when in EL2
* MDCR_EL3.SCCD disables the counter when Secure
Add the code to support these bits.
(Note that there is a third documented counter-disable
bit, MDCR_EL3.MCCD, which disables the counter when in
EL3. This is not present until FEAT_PMUv3p7, so is
out of scope for now.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-9-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Our feature test functions that check the PMU version are named
isar_feature_{aa32,aa64,any}_pmu_8_{1,4}. This doesn't match the
current Arm ARM official feature names, which are FEAT_PMUv3p1 and
FEAT_PMUv3p4. Rename these functions to _pmuv3p1 and _pmuv3p4.
This commit was created with:
sed -i -e 's/pmu_8_/pmuv3p/g' target/arm/*.[ch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-8-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In pmccntr_op_finish() and pmevcntr_op_finish() we calculate the next
point at which we will get an overflow and need to fire the PMU
interrupt or set the overflow flag. We do this by calculating the
number of nanoseconds to the overflow event and then adding it to
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL). However, we don't check
whether that signed addition overflows, which can happen if the next
PMU interrupt would happen massively far in the future (250 years or
more).
Since QEMU assumes that "when the QEMU_CLOCK_VIRTUAL rolls over" is
"never", the sensible behaviour in this situation is simply to not
try to set the timer if it would be beyond that point. Detect the
overflow, and skip setting the timer in that case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-7-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The logic in pmu_counter_enabled() for handling the 'prohibit event
counting' bits MDCR_EL2.HPMD and MDCR_EL3.SPME is written in a way
that assumes that EL2 is never Secure. This used to be true, but the
architecture now permits Secure EL2, and QEMU can emulate this.
Refactor the prohibit logic so that we effectively OR together
the various prohibit bits when they apply, rather than trying to
construct an if-else ladder where any particular state of the CPU
ends up in exactly one branch of the ladder.
This fixes the Secure EL2 case and also is a better structure for
adding the PMUv8.5 bits MDCR_EL2.HCCD and MDCR_EL3.SCCD.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-6-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The architecture requires that if PMCR.LC is set (for a 64-bit cycle
counter) then PMCR.D (which enables the clock divider so the counter
ticks every 64 cycles rather than every cycle) should be ignored. We
were always honouring PMCR.D; fix the bug so we correctly ignore it
in this situation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-5-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The PMU cycle and event counter infrastructure design requires that
operations on the PMU register fields are wrapped in pmu_op_start()
and pmu_op_finish() calls (or their more specific pmmcntr and
pmevcntr equivalents). This includes any changes to registers which
affect whether the counter should be enabled or disabled, but we
forgot to do this.
The effect of this bug is that in sequences like:
* disable the cycle counter (PMCCNTR) using the PMCNTEN register
* write a value such as 0xfffff000 to the PMCCNTR
* restart the counter by writing to PMCNTEN
the value written to the cycle counter is corrupted, and it starts
counting from the wrong place. (Essentially, we fail to record that
the QEMU_CLOCK_VIRTUAL timestamp when the counter should be considered
to have started counting is the point when PMCNTEN is written to enable
the counter.)
Add the necessary bracketing calls, so that updates to the various
registers which affect whether the PMU is counting are handled
correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-4-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When the cycle counter overflows, we are intended to set bit 31 in PMOVSR
to indicate this. However a missing ULL suffix means that we end up
setting all of bits 63-31. Fix the bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In Armv8.6, a new AArch32 ID register ID_DFR1 is defined; implement
it. We don't have any CPUs with features that they need to advertise
here yet, but plumbing in the ID register gives it the right name
when debugging and will help in future when we do add a CPU that
has non-zero ID_DFR1 fields.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-5-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In Armv8.6 a new AArch32 ID register ID_MMFR5 is defined.
Implement this; we want to be able to use it to report to
the guest that we implement FEAT_ETS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-4-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In the AArch32 ID register scheme, coprocessor registers with
encoding cp15, 0, c0, c{0-7}, {0-7} are all in the space covered by
what in v6 and v7 was called the "CPUID scheme", and are supposed to
RAZ if they're not allocated to a specific ID register. For our
pre-v8 CPUs we get this right, because the regdefs in
id_pre_v8_midr_cp_reginfo[] cover these RAZ requirements. However
for v8 we failed to put in the necessary patterns to cover this, so
we end up UNDEFing on everything we didn't have an ID register for.
This is a problem because in Armv8 some encodings in 0, c0, c3, {0-7}
are now being used for new ID registers, and guests might thus start
trying to read them. (We already have one of these: ID_PFR2.)
For v8 CPUs, we already have regdefs for 0, c0, c{0-2}, {0-7} (that
is, the space is completely allocated with no reserved spaces). Add
entries to v8_idregs[] covering 0, c0, c3, {0-7}:
* c3, {0-2} is the reserved AArch32 space corresponding to the
AArch64 MVFR[012]_EL1
* c3, {3,5,6,7} are reserved RAZ for both AArch32 and AArch64
(in fact some of these are given defined meanings in Armv8.6,
but we don't implement them yet)
* c3, 4 is ID_PFR2 (already defined)
We then programmatically add RAZ patterns for AArch32 for
0, c0, c{4..15}, {0-7}:
* c4-c7 are unused, and not shared with AArch64 (these
are the encodings corresponding to where the AArch64
specific ID registers live in the system register space)
* c8-c15 weren't required to RAZ in v6/v7, but v8 extends
the AArch32 reserved-should-RAZ space to cover these;
the equivalent area of the AArch64 sysreg space is not
defined as must-RAZ
Note that the architecture allows some registers in this space
to return an UNKNOWN value; we always return 0.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When the user queries CPU models via QMP there is a 'deprecated' flag
present, however, this is not done for the CLI '-cpu help' command.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Some files wrongly contain the same word twice in a row.
One of them should be removed or replaced.
Message-Id: <20220722145859.1952732-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Change the representation of the TCR_EL* registers in the CPU state
struct from struct TCR to uint64_t. This allows us to drop the
custom vmsa_ttbcr_raw_write() function, moving the "enforce RES0"
checks to their more usual location in the writefn
vmsa_ttbcr_write(). We also don't need the resetfn any more.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-7-peter.maydell@linaro.org
Change the representation of the VSTCR_EL2 and VTCR_EL2 registers in
the CPU state struct from struct TCR to uint64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-6-peter.maydell@linaro.org
We have a bug in our handling of accesses to the AArch32 VTCR
register on big-endian hosts: we were not adjusting the part of the
uint64_t field within TCR that the generated code would access. That
can be done with offsetoflow32(), by using an ARM_CP_STATE_BOTH cpreg
struct, or by defining a full set of read/write/reset functions --
the various other TCR cpreg structs used one or another of those
strategies, but for VTCR we did not, so on a big-endian host VTCR
accesses would touch the wrong half of the register.
Use offsetoflow32() in the VTCR register struct. This works even
though the field in the CPU struct is currently a struct TCR, because
the first field in that struct is the uint64_t raw_tcr.
None of the other TCR registers have this bug -- either they are
AArch64 only, or else they define resetfn, writefn, etc, and
expect to be passed the full struct pointer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-5-peter.maydell@linaro.org
The only caller of regime_tcr() is now regime_tcr_value(); fold the
two together, and use the shorter and more natural 'regime_tcr'
name for the new function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-4-peter.maydell@linaro.org
The regime_tcr() function returns a pointer to a struct TCR
corresponding to the TCR controlling a translation regime. The
struct TCR has the raw value of the register, plus two fields mask
and base_mask which are used as a small optimization in the case of
32-bit short-descriptor lookups. Almost all callers of regime_tcr()
only want the raw register value. Define and use a new
regime_tcr_value() function which returns only the raw 64-bit
register value.
This is a preliminary to removing the 32-bit short descriptor
optimization -- it only saves a handful of bit operations, which is
tiny compared to the overhead of doing a page table walk at all, and
the TCR struct is awkward and makes fixing
https://gitlab.com/qemu-project/qemu/-/issues/1103 unnecessarily
difficult.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-2-peter.maydell@linaro.org
We were only checking for SVE disabled and not taking into
account PSTATE.SM to check SME disabled, which resulted in
vectors being incorrectly truncated.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220713045848.217364-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When PSTATE.SM, VL = SVL even if SVE is disabled.
This is visible in kselftest ssve-test.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220713045848.217364-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can handle both exception entry and exception return by
hooking into aarch64_sve_change_el.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-32-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This new behaviour is in the ARM pseudocode function
AArch64.CheckFPAdvSIMDEnabled, which applies to AArch32
via AArch32.CheckAdvSIMDOrFPEnabled when the EL to which
the trap would be delivered is in AArch64 mode.
Given that ARMv9 drops support for AArch32 outside EL0, the trap EL
detection ought to be trivially true, but the pseudocode still contains
a number of conditions, and QEMU has not yet committed to dropping A32
support for EL[12] when v9 features are present.
Since the computation of SME_TRAP_NONSTREAMING is necessarily different
for the two modes, we might as well preserve bits within TBFLAG_ANY and
allocate separate bits within TBFLAG_A32 and TBFLAG_A64 instead.
Note that DDI0616A.a has typos for bits [22:21] of LD1RO in the table
of instructions illegal in streaming mode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The target/arm/helper.c file is very long and is a grabbag of all
kinds of functionality. We have already a debug_helper.c which has
code for implementing architectural debug. Move the code which
defines the debug-related system registers out to this file also.
This affects the define_debug_regs() function and the various
functions and arrays which are used only by it.
The functions raw_write() and arm_mdcr_el2_eff() and
define_debug_regs() now need to be global rather than local to
helper.c; everything else is pure code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220630194116.3438513-3-peter.maydell@linaro.org
Before moving debug system register helper functions to a
different file, fix the code style issues (mostly block
comment syntax) so checkpatch doesn't complain about the
code-motion patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220630194116.3438513-2-peter.maydell@linaro.org
Perform the cleanup in the FIXME comment in common_semi_gdb_syscall.
Do not modify guest registers until the syscall is complete,
which in the gdbstub case is asynchronous.
In the synchronous non-gdbstub case, use common_semi_set_ret
to set the result. Merge set_swi_errno into common_semi_cb.
Rely on the latter for combined return value / errno setting.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We need SVL separate from VL for RDSVL et al, as well as
ZA storage loads and stores, which do not require PSTATE.SM.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When Streaming SVE mode is enabled, the size is taken from
SMCR_ELx instead of ZCR_ELx. The format is shared, but the
set of vector lengths is not. Further, Streaming SVE does
not require any particular length to be supported.
Adjust sve_vqm1_for_el to pass the current value of PSTATE.SM
to the new function.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pull the three sve_vq_* values into a structure.
This will be reused for SME.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These two instructions are aliases of MSR (immediate).
Use the two helpers to properly implement svcr_write.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are required to determine if various insns
are allowed to issue.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the streaming mode identification register, and the
two streaming priority registers. For QEMU, they are all RES0.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These cpregs control the streaming vector length and whether the
full a64 instruction set is allowed while in streaming mode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cpreg is used to access two new bits of PSTATE
that are not visible via any other mechanism.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is CheckSMEAccess, which is the basis for a set of
related tests for various SME cpregs and instructions.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is part of SME, but isn't closely related to the
rest of the extension.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620175235.60881-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since DDI0487F.a, the RW bit is RAO/WI. When specifically
targeting such a cpu, e.g. cortex-a76, it is legitimate to
ignore the bit within the secure monitor.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1062
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220609214657.1217913-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Because reset always initializes the AA64 version, SCR_EL3,
test the mode of EL3 instead of the type of the cpreg.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220609214657.1217913-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We were using arm_is_secure and is_a64, which are
tests against the current EL, as opposed to
arm_el_is_aa64 and arm_is_secure_below_el3, which
can be applied to a different EL than current.
Consolidate the two tests.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220609202901.1177572-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We no longer need this value during translation,
as it is now handled within the helpers.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220609202901.1177572-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is allocated from the existing block of id registers,
so it is already RES0 for cpus that do not implement SME.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will be used for both Normal and Streaming SVE, and the value
does not necessarily come from ZCR_ELx. While we're at it, emphasize
the units in which the value is returned.
Patch produced by
git grep -l sve_zcr_len_for_el | \
xargs -n1 sed -i 's/sve_zcr_len_for_el/sve_vqm1_for_el/g'
and then adding a function comment.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bitmap need only hold 15 bits; bitmap is over-complicated.
We can simplify operations quite a bit with plain logical ops.
The introduction of SVE_VQ_POW2_MAP eliminates the need for
looping in order to search for powers of two. Simply perform
the logical ops and use count leading or trailing zeros as
required to find the result.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function is used only once, and will need modification
for Streaming SVE mode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This check is buried within arm_hcr_el2_eff(), but since we
have to have the explicit check for CPTR_EL2.TZ, we might as
well just check it once at the beginning of the block.
Once this is done, we can test HCR_EL2.{E2H,TGE} directly,
rather than going through arm_hcr_el2_eff().
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM pseudocode function CheckNormalSVEEnabled uses this
predicate now, and I think it's a bit clearer.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM pseudocode function NVL uses this predicate now,
and I think it's a bit clearer. Simplify the pseudocode
condition by noting that IsInHost is always false for EL1.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This (newish) ARM pseudocode function is easier to work with
than open-coded tests for HCR_E2H etc. Use of the function
will be staged into the code base in parts.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of checking these bits in fp_exception_el and
also in sve_exception_el, document that we must compare
the results. The only place where we have not already
checked that FP EL is zero is in rebuild_hflags_a64.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We handle this routing in raise_exception. Promoting the value early
means that we can't directly compare FPEXC_EL and SVEEXC_EL.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With SME, the vector length does not only come from ZCR_ELx.
Comment that this is either NVL or SVL, like the pseudocode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220607203306.657998-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220604040607.269301-28-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
