The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The note test requires gcc 10 for -mbranch-protection=standard.
The mmap test uses PROT_BTI and does not require special compiler support.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
-----BEGIN PGP SIGNATURE-----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=ZpMy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-10-26' into staging
* qtest fixes (e.g. memory leaks)
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
# gpg: Signature made Mon 26 Oct 2020 09:34:04 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-10-26: (31 commits)
tests/acceptance: Use .ppm extention for Portable PixMap files
tests/acceptance: Remove unused import
test/docker/dockerfiles: Add missing packages for acceptance tests
tests/acceptance: Enable AVOCADO_ALLOW_UNTRUSTED_CODE in the gitlab-CI
test/acceptance: Remove the CONTINUOUS_INTEGRATION tags
tests/acceptance/ppc_prep_40p: Fix the URL to the NetBSD-4.0 archive
scripts/oss-fuzz: ignore the generic-fuzz target
scripts/oss-fuzz: use hardlinks instead of copying
fuzz: register predefined generic-fuzz configs
fuzz: add generic-fuzz configs for oss-fuzz
fuzz: add an "opaque" to the FuzzTarget struct
fuzz: Add instructions for using generic-fuzz
scripts/oss-fuzz: Add crash trace minimization script
scripts/oss-fuzz: Add script to reorder a generic-fuzzer trace
fuzz: add a crossover function to generic-fuzzer
fuzz: add a DISABLE_PCI op to generic-fuzzer
fuzz: Add support for custom crossover functions
fuzz: Add fuzzer callbacks to DMA-read functions
fuzz: Declare DMA Read callback function
fuzz: Add DMA support to the generic-fuzzer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The HMP 'screendump' command generates Portable PixMap files.
Make it obvious by using the .ppm file extention.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201021105035.2477784-3-f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201021105035.2477784-2-f4bug@amsat.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some of the "check-acceptance" tests are still skipped in the CI
since the docker images do not provide the necessary packages, e.g.
the netcat binary. Add them to get more test coverage.
Message-Id: <20201023073351.251332-5-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are not running the acceptance tests on Travis anymore, so these
checks can be removed now.
Message-Id: <20201023073351.251332-3-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The current URL on cdn.netbsd.org is failing - using archive.netbsd.org
instead seems to be fine.
Message-Id: <20201023073351.251332-2-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We call get_generic_fuzz_configs, which fills an array with
predefined {name, args, objects} triples. For each of these, we add a
new FuzzTarget, that uses a small wrapper to set
QEMU_FUZZ_{ARGS,OBJECTS} to the corresponding predefined values.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-16-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Predefine some generic-fuzz configs. For each of these, we will create a
separate FuzzTarget that can be selected through argv0 and, therefore,
fuzzed on oss-fuzz.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-15-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It can be useful to register FuzzTargets that have nearly-identical
initialization handlers (e.g. for using the same fuzzing code, with
different configuration options). Add an opaque pointer to the
FuzzTarget struct, so that FuzzTargets can hold some data, useful for
storing target-specific configuration options, that can be read by the
get_init_cmdline function.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-14-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-10-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This new operation is used in the next commit, which concatenates two
fuzzer-generated inputs. With this operation, we can prevent the second
input from clobbering the PCI configuration performed by the first.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20201023150746.107063-9-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
libfuzzer supports a "custom crossover function". Libfuzzer often tries
to blend two inputs to create a new interesting input. Sometimes, we
have a better idea about how to blend inputs together. This change
allows fuzzers to specify a custom function for blending two inputs
together.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20201023150746.107063-8-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When a virtual-device tries to access some buffer in memory over DMA, we
add call-backs into the fuzzer(next commit). The fuzzer checks verifies
that the DMA request maps to a physical RAM address and fills the memory
with fuzzer-provided data. The patterns that we use to fill this memory
are specified using add_dma_pattern and clear_dma_patterns operations.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20201023150746.107063-5-alxndr@bu.edu>
[thuth: Reformatted one comment according to the QEMU coding style]
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch compares TYPE_PCI_DEVICE objects against the user-provided
matching pattern. If there is a match, we use some hacks and leverage
QOS to map each possible BAR for that device. Now fuzzed inputs might be
converted to pci_read/write commands which target specific. This means
that we can fuzz a particular device's PCI configuration space,
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20201023150746.107063-4-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This is a generic fuzzer designed to fuzz a virtual device's
MemoryRegions, as long as they exist within the Memory or Port IO (if it
exists) AddressSpaces. The fuzzer's input is interpreted into a sequence
of qtest commands (outb, readw, etc). The interpreted commands are
separated by a magic seaparator, which should be easy for the fuzzer to
guess. Without ASan, the separator can be specified as a "dictionary
value" using the -dict argument (see libFuzzer documentation).
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-3-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The g_list_remove_link doesn't free the link element,
opposed to what I thought.
Switch to g_list_delete_link that does free it.
Also refactor the code a bit.
Thanks for Max Reitz for helping me with this.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201019163702.471239-4-mlevitsk@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
By a mistake I added the pending events in a wrong order.
Fix this by using g_list_append.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201019163702.471239-3-mlevitsk@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This test won't work if qemu was compiled without CONFIG_NPCM7XX, as
pointed out by Thomas Huth on a different patch.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20201023210637.351238-2-hskinnemoen@google.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The qtests can be run directly by specifying the QEMU binary with the
QTEST_QEMU_BINARY environment variable, for example:
$ QTEST_QEMU_BINARY=x86_64-softmmu/qemu-system-x86_64 tests/qtest/test-hmp
However, if you specify a binary without a path, for example with
QTEST_QEMU_BINARY=qemu-system-x86_64 if the QEMU binary is in your
$PATH, then the test currently simply crashes.
Let's try a little bit smarter here by looking for the final '-'
instead of the slash.
Message-Id: <20201012114816.43546-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
These cases are fixed by previous patches around block_status and
is_allocated.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20200924194003.22080-6-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow vu_message_read to be replaced by one which will make use of the
QIOChannel functions. Thus reading vhost-user message won't stall the
guest. For slave channel, we still use the default vu_message_read.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20200918080912.321299-2-coiby.xu@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
this fixes non-TCG builds broken recently by replay reverse debugging.
Stub the needed functions in stub/, splitting roughly between functions
needed only by system emulation, by system emulation and tools,
and by everyone. This includes duplicating some code in replay/, and
puts the logic for non-replay related events in the replay/ module (+
the stubs), so this should be revisited in the future.
Surprisingly, only _one_ qtest was affected by this, ide-test.c, which
resulted in a buzz as the bh events were never delivered, and the bh
never executed.
Many other subsystems _should_ have been affected.
This fixes the immediate issue, however a better way to group replay
functionality to TCG-only code could be developed in the long term.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20201013192123.22632-4-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
the tests assume TCG is available, thus breaking
for TCG-only tests, where only the TCG accelerator option
is passed to the QEMU binary.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20201013192123.22632-3-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Starting with meson 0.56, colons are used to separate the subproject name
from the test name. Use dash or slash depending on what looks nicer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This test exercises the various modes of the npcm7xx timer. In
particular, it triggers the bug found by the fuzzer, as reported here:
https://lists.gnu.org/archive/html/qemu-devel/2020-09/msg02992.html
It also found several other bugs, especially related to interrupt
handling.
The test exercises all the timers in all the timer modules, which
expands to 180 test cases in total.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20201008232154.94221-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
mypy wants to ensure there's consistency between the kwargs arguments
types and any unspecified keyword arguments. In this case, conv_keys is
a bool, but the remaining keys are Any type. Mypy (correctly) infers the
**kwargs type to be **Dict[str, str], which is not compatible with
conv_keys: bool.
Because QMP typing is a little fraught right now anyway, re-type kwargs
to Dict[str, Any] which has the benefit of silencing this check right
now.
A future re-design might type these more aggressively, but this will
give us a baseline to work from with minimal disruption.
(Thanks Kevin Wolf for the debugging assist here)
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 20201006235817.3280413-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This test case uses the 9pfs 'local' driver to create a directory
and then checks if the expected directory was actually created
(as real directory) on host side.
This patch introduces a custom split() implementation, because
the test code requires non empty array elements as result. For
that reason g_strsplit() would not be a good alternative, as
it would require additional filter code for reshuffling the
array, and the resulting code would be even more complex than
this split() function.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <be342f236842272275f65dbe05587f0a5409ad77.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
This new public function virtio_9p_test_path() allows 9pfs
'local' tests to translate a path from guest scope to host
scope. For instance by passing an empty string it would
return the root path on host of the exported 9pfs tree.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <b563d3c73c6391ec927a2622c9f65c09ca56bd83.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Before running the first 9pfs test case, make sure the test directory
for running the 9pfs 'local' tests on is entirely empty. For that
reason simply delete the test directory (if any) before (re)creating
it on test suite startup.
Note: The preferable precise behaviour would be the test directory
only being wiped once *before* a test suite run. Right now the test
directory is also wiped at the *end* of a test suite run because
libqos is calling the virtio_9p_register_nodes() callback for some
reason also when a test suite completed. This is suboptimal as
developers cannot immediately see what files and directories the
9pfs local tests created precisely after the test suite completed.
But fortunately the test directory is not wiped if some test failed.
So it is probably not worth it drilling another hole into libqos
for this issue.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <b30776ea3289dc40dabc7d0063d825d21d9a65bf.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
This patch introduces 9pfs test cases using the 9pfs 'local'
filesystem driver which reads/writes/creates/deletes real files
and directories.
In this initial version, there is only one local test which actually
only checks if the 9pfs 'local' device was created successfully.
Before the 9pfs 'local' tests are run, a test directory 'qtest-9p-local'
is created (with world rwx permissions) under the current working
directory. At this point that test directory is not auto deleted yet.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <81fc4b3b6b6c9bf7999e79f5e7cbc364a5f09ddb.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
All existing 9pfs test cases are using the 'synth' fs driver so far, which
means they are not accessing real files, but a purely simulated (in RAM
only) file system.
Let's make this clear by changing the prefix of the individual qtest case
names from 'fs/' to 'synth/'. That way they'll be easily distinguishable
from upcoming new 9pfs test cases supposed to be using a different fs
driver.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <e04e75acb849b085c6d6320b2433a15fa935bcff.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
-----BEGIN PGP SIGNATURE-----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=BOxw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20201017' into staging
MIPS patches queue
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
# gpg: Signature made Sat 17 Oct 2020 14:59:53 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20201017: (44 commits)
target/mips: Increase number of TLB entries on the 34Kf core (16 -> 64)
MAINTAINERS: Remove duplicated Malta test entries
MAINTAINERS: Downgrade MIPS Boston to 'Odd Fixes', fix Paul Burton mail
MAINTAINERS: Put myself forward for MIPS target
MAINTAINERS: Remove myself
docs/system: Update MIPS CPU documentation
tests/acceptance: Add MIPS record/replay tests
hw/mips: Remove exit(1) in case of missing ROM
hw/mips: Rename TYPE_MIPS_BOSTON to TYPE_BOSTON
hw/mips: Simplify code using ROUND_UP(INITRD_PAGE_SIZE)
hw/mips: Simplify loading 64-bit ELF kernels
hw/mips/malta: Use clearer qdev style
hw/mips/malta: Move gt64120 related code together
hw/mips/malta: Fix FPGA I/O region size
target/mips/cpu: Display warning when CPU is used without input clock
hw/mips/cps: Do not allow use without input clock
hw/mips/malta: Set CPU frequency to 320 MHz
hw/mips/boston: Set CPU frequency to 1 GHz
hw/mips/cps: Expose input clock and connect it to CPU cores
hw/mips/jazz: Correct CPU frequencies
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
