The number of slots per page being 511 (i.e. not a power of two) means
that the (32-bit) read and write indexes going beyond 2^32 will likely
disturb operation. The hypervisor side gets I/O req server creation
extended so we can indicate that we're using suitable atomic accesses
where needed, allowing it to atomically canonicalize both pointers when
both have gone through at least one cycle.
The Xen side counterpart (which is not a functional prereq to this
change, albeit a build one) went in already (commit b7007bc6f9).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
This adds "--enable-jemalloc" and "--disable-jemalloc" to allow linking
to jemalloc memory allocator.
We have already tcmalloc support,
but it seem to not working well with a lot of iothreads/disks.
The main problem is that tcmalloc use a shared thread cache of 16MB
by default.
With more threads, this cache is shared, and some bad garbage collections
can occur if the cache is too low.
It's possible to tcmalloc cache increase it with a env var:
TCMALLOC_MAX_TOTAL_THREAD_CACHE_BYTES=256MB
With default 16MB, performances are really bad with more than 2 disks.
Increasing to 256MB, it's helping but still have problem with 16 disks/iothreads.
Jemalloc don't have performance problem with default configuration.
Here the benchmark results in iops of 1 qemu vm randread 4K iodepth=32,
with rbd block backend (librbd is doing a lot of memory allocation),
1 iothread by disk
glibc malloc
------------
1 disk 29052
2 disks 55878
4 disks 127899
8 disks 240566
15 disks 269976
jemalloc
--------
1 disk 41278
2 disks 75781
4 disks 195351
8 disks 294241
15 disks 298199
tcmalloc 2.2.1 default 16M cache
--------------------------------
1 disk 37911
2 disks 67698
4 disks 41076
8 disks 43312
15 disks 37569
tcmalloc : 256M cache
---------------------------
1 disk 33914
2 disks 58839
4 disks 148205
8 disks 213298
15 disks 218383
Signed-off-by: Alexandre Derumier <aderumier@odiso.com>
Message-Id: <1434711418-20429-1-git-send-email-aderumier@odiso.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Every arch adds its disas configury to both its own config as well
config_disas_all. Make a small function do to both at once.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-Id: <1440844439-19391-1-git-send-email-crosthwaite.peter@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's support reading and writing of control registers for kvm and tcg.
We have to take care of flushing the tlb (tcg) and pushing the changed
registers into kvm.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently VSS dll/tlb files for use in w32 builds are only built as a
result of having been added to the general 'tools' target alongside
qemu-ga. This is fine for default make target, but if we build
qemu-ga directly via `make qemu-ga.exe`, the VSS files are not
created.
Fix this by moving the VSS dependencies to qemu-ga.exe directly.
With this move we can move the VSS files back out of 'tools',
and drop the extra handling from MSI target in Makefile.
Now we can build qemu-ga MSI package with:
./configure ...
make qemu-ga.exe
make msi
or simply:
./configure ...
make msi
and no longer need to do a full build beforehand.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently, if we don't explicitly disable support for MSI installer
via --disable-guest-agent-msi, the configure variable that tracks
the flag, 'guest_agent_msi', never gets set unless one of the probes
fails. Subsequent code then treats this unset value the same as if it
were a "yes" value (via != "no" style checks).
Instead, set the default "yes" value explicitly after the probes, then
make subsequent code expect the values to be set.
This makes it easier to report on whether or not MSI support was
enabled via probe by looking at the ./configure summary.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
MSI probe assumes that qemu-ga support has been probed already, but in
cases where --enable-guest-agent/--disable-guest-agent have not been
passed to configure, qemu-ga support may end up getting enabled later,
as is the case with w32 builds. This leads to MSI probe prematurely
reporting error due to lack of qemu-ga support.
Fix this by moving MSI installer probe after the final qga probes.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Use NetUserSetInfo() to set the user password.
This function is notoriously known to be problematic for users with EFS
encrypted files. But the alternative, NetUserChangePassword() requires
the old password. Nevertheless, The EFS file should be recovered by
changing back to the old password.
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently we need to examine config-host.mak to determine whether
options/probes for MSI package generation had desired result. Report
this more prominently in ./configure summary as we do with other
guest agent configure options.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
All tcg host architectures now support the guest base and as
there is no real performance lost, it can be always enabled.
Anyway, guest base use can be disabled lively by setting guest
base to 0.
CONFIG_USE_GUEST_BASE is defined as (USE_GUEST_BASE && USER_ONLY),
it should have to be replaced by CONFIG_USER_ONLY in non CONFIG_USER_ONLY
parts, but as some other parts are using !CONFIG_SOFTMMU I have chosen to
use !CONFIG_SOFTMMU instead.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1440373328-9788-2-git-send-email-laurent@vivier.eu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The cocoa GUI frontend assumes it is the only GUI (it redefines
main() so it always gets control before the rest of QEMU), so
it does not play well with other UIs like SDL or GTK. (Mostly
people building QEMU on OSX don't have the necessary dependencies
available for configure to build those other front ends, so
mostly this problem goes unnoticed.)
Make configure automatically disable the SDL and GTK front ends
if the cocoa front end is enabled. (We were sort of attempting
to do this for SDL before, but not in a way that worked very well.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: John Arbuckle <programmingkidx@gmail.com>
Message-id: 1439565052-3457-1-git-send-email-peter.maydell@linaro.org
* vhost-scsi fix from Igor and Lu Lina
* a build system fix from Daniel
* two more multi-arch-related patches from Peter C.
* TCG patches from myself and Sergey Fedorov
* RCU improvement from Wen Congyang
* a few more simple cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVzmCgAAoJEL/70l94x66DhFgH/1m3iGac2Ks3vAUAdS2HBcxC
EeziMwWFmkrfbtzUkz/jE0NG5uA2Bs8OFHsC8vmQFwkpDbGUlJ1zd5/N5UOHMG3d
zF0vd+nKNw9C1Fo0/LPyQSeP64/xXEMTmFLqmYf4ZOowz8lr/m6WYrMIzKUoXSEn
FeRtq78moDT8qwF372j8aoQUUpsctXDHBQHORZdcERvlc4mxojeJ3+mNViR2bv3r
92PwGvrJ26mQXEKmGo5O1VM4k7QVg7xJQfgE11x7ShE2E9fJDMgts0Q/xCjWCLwS
BXtEtbd9QeFEfG/mlRFevGtuvksq98m0hN7lAWb13zWmlJFuLyyMmlGfGAlU55Q=
=Y2DB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* SCSI fixes from Stefan and Fam
* vhost-scsi fix from Igor and Lu Lina
* a build system fix from Daniel
* two more multi-arch-related patches from Peter C.
* TCG patches from myself and Sergey Fedorov
* RCU improvement from Wen Congyang
* a few more simple cleanups
# gpg: Signature made Fri 14 Aug 2015 22:41:52 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
disas: Defeature print_target_address
hw: fix mask for ColdFire UART command register
scsi-generic: identify AIO callbacks more clearly
scsi-disk: identify AIO callbacks more clearly
scsi: create restart bottom half in the right AioContext
configure: only add CONFIG_RDMA to config-host.h once
qemu-nbd: remove unnecessary qemu_notify_event()
vhost-scsi: Clarify vhost_virtqueue_mask argument
exec: use macro ROUND_UP for alignment
rcu: Allow calling rcu_(un)register_thread() during synchronize_rcu()
exec: drop cpu_can_do_io, just read cpu->can_do_io
cpu_defs: Simplify CPUTLB padding logic
cpu-exec: Do not invalidate original TB in cpu_exec_nocache()
vhost/scsi: call vhost_dev_cleanup() at unrealize() time
virtio-scsi-test: Add test case for tail unaligned WRITE SAME
scsi-disk: Fix assertion failure on WRITE SAME
tests: virtio-scsi: clear unit attention after reset
scsi-disk: fix cmd.mode field typo
virtio-scsi: use virtqueue_map_sg() when loading requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For unknown reasons (probably a git rebase merge mistake)
commit 2da776db48
Author: Michael R. Hines <mrhines@us.ibm.com>
Date: Mon Jul 22 10:01:54 2013 -0400
rdma: core logic
Adds CONFIG_RDMA to config-host.h twice, as can be seen
in the generated file:
$ grep CONFIG_RDMA config-host.h
#define CONFIG_RDMA 1
#define CONFIG_RDMA 1
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1438345403-32467-1-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8e9b0d2 (ui: convert VNC websockets to use crypto APIs) dropped
the --enable-vnc-ws option but forgot to update the help text. Fix this.
Cc: Daniel P. Berrange <berrange@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1437749257-3313-1-git-send-email-afaerber@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unfortunately Ubuntu's pkg-config information for gnutls is broken
for the static linking case, and outputs --libs options which the
compiler does not recognize. Work around this problem by testing
that the --cflags/--libs output will at least allow compilation
before enabling gnutls support.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1437758888-22486-1-git-send-email-peter.maydell@linaro.org
In nettle 3, cbc_encrypt() accepts 'nettle_cipher_func' instead of
'nettle_crypt_func' and these two differ in 'const' qualifier of the
first argument. The build fails with:
In file included from crypto/cipher.c:71:0:
./crypto/cipher-nettle.c: In function ‘qcrypto_cipher_encrypt’:
./crypto/cipher-nettle.c:154:38: error: passing argument 2 of
‘nettle_cbc_encrypt’ from incompatible pointer type
cbc_encrypt(ctx->ctx_encrypt, ctx->alg_encrypt,
^
In file included from ./crypto/cipher-nettle.c:24:0,
from crypto/cipher.c:71:
/usr/include/nettle/cbc.h:48:1: note: expected
‘void (*)(const void *, size_t, uint8_t *, const uint8_t *)
but argument is of type
‘void (*)( void *, size_t, uint8_t *, const uint8_t *)
To allow both versions, we switch to the new definition and #if typedef
it for old versions.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1436548682-9315-2-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVnQWdAAoJEL/70l94x66D6OgIAKJlzQfmy5w7Q9WD4vCMhD76
JrpLSsn7Gx/Bws0Nu9nLQlqun5z4hiUxyG2kP/WqD9+tV3cpSMSyrG6ImVdqKnQ5
+Z8WJZuREkQv0aqDUjQVST+eIDZuh2LWJXAjhgsCXUHY77eWb/7WmKT79xJOa+5C
5xB1qxudqX5IsTvpiKKPbmUGYkAcvRX1dUSaFwRIMO0UyKn59B9WfM9a5slIbLW7
XfI8+wEJshTVLuQkkTfdidWQc5M5DwlmO7ESUNR/BRPCPFeyjcDqgQY5pBM5XVo9
C+S0R3zIt3Ew0fhCtLRyjlIT0bGfwjbU5HRiHcyldBKhNUZZjSUoOWJnYRHXUDY=
=H8wA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Bugfixes and Daniel Berrange's crypto library.
# gpg: Signature made Wed Jul 8 12:12:29 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
ossaudio: fix memory leak
ui: convert VNC to use generic cipher API
block: convert qcow/qcow2 to use generic cipher API
ui: convert VNC websockets to use crypto APIs
block: convert quorum blockdrv to use crypto APIs
crypto: add a nettle cipher implementation
crypto: add a gcrypt cipher implementation
crypto: introduce generic cipher API & built-in implementation
crypto: move built-in D3DES implementation into crypto/
crypto: move built-in AES implementation into crypto/
crypto: introduce new module for computing hash digests
vl: move rom_load_all after machine init done
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the direct use of gnutls for hash processing in the
websockets code, in favour of using the crypto APIs. This
allows the websockets code to be built unconditionally
removing countless conditional checks from the VNC code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1435770638-25715-9-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get rid of direct use of gnutls APIs in quorum blockdrv in
favour of using the crypto APIs. This avoids the need to
do conditional compilation of the quorum driver. It can
simply report an error at file open file instead if the
required hash algorithm isn't supported by QEMU.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1435770638-25715-8-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we are linking to gnutls already and gnutls is built against
nettle, then we should use nettle as a cipher backend in
preference to our built-in backend.
This will be used when linking against some GNUTLS 2.x versions
and all GNUTLS 3.x versions.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1435770638-25715-7-git-send-email-berrange@redhat.com>
[Change "#elif" to "#elif defined". - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we are linking to gnutls already and gnutls is built against
gcrypt, then we should use gcrypt as a cipher backend in
preference to our built-in backend.
This will be used when linking against GNUTLS 1.x and many
GNUTLS 2.x versions.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1435770638-25715-6-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PCIAddress inforfation is obtained via SetupApi, which provides the
information about address, bus, etc. We look throught entire device tree
in the system and try to find device object for given volume. For this PDO
SetupDiGetDeviceRegistryProperty is called, which reads PCI configuration
for a given devicei if it is possible.
This is the most convinient way for a userspace service. The lookup is
performed for every volume available. However, this information is
not mandatory for vss-provider.
In order to use SetupApi we need to notify linker about it. We do not need
to install additional libs, so we do not make separate configuration
option to use libsetupapi.su
SetupApi gives as the same information as kernel driver
with IRP_MN_QUERY_INTERFACE.
https://support.microsoft.com/en-us/kb/253232
Signed-off-by: Olga Krishtal <okrishtal@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Eric Blake <eblake@redhat.com>
CC: Michael Roth <mdroth@linux.vnet.ibm.com>
* stub out get_pci_info if !CONFIG_QGA_NTDDSCSI
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This header file provides w32 ioctl definitions for working with disk
devices. Older versions of mingw do not expose this in a useable way,
so add a configure check and report it via CONFIG_QGA_NTDDSCSI.
Subsequent patches will use this macro to stub out functionality that
relies on this in cases where it's not available.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Add the iphlpapi library to use APIs such as GetAdaptersInfo and
GetAdaptersAddresses.
Signed-off-by: Kirk Allan <kallan@suse.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Introduce a new crypto/ directory that will (eventually) contain
all the cryptographic related code. This initially defines a
wrapper for initializing gnutls and for computing hashes with
gnutls. The former ensures that gnutls is guaranteed to be
initialized exactly once in QEMU regardless of CLI args. The
block quorum code currently fails to initialize gnutls so it
only works by luck, if VNC server TLS is not requested. The
hash APIs avoids the need to litter the rest of the code with
preprocessor checks and simplifies callers by allocating the
correct amount of memory for the requested hash.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1435770638-25715-2-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Almost exclusively bugfixes, though in this case,
we are adding functionality to the pxb in order
to make OVMF work on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVjVb/AAoJECgfDbjSjVRpeaEH/2bwK7BGgczEQ7fhzIEaQSQq
SV7aychNZvUFASXLV6aVmQCdYixZxlI9KDn0pMRYntUcjxRRB48U3N5Sy4km46Pw
LLN3vxGzHazlE7AJ5c+WVDf0e2k7v3CpZ/TKXzPHmvZXIuBfjKXtKzBgyQYxGkmL
JgRrRSHDrsbvfmhI4uHMpCTYs/WeY1cuA1IzvimBjmvVP5kkko4NoX+HEWmGJ6WK
13fQuV+Cvz7Yk40HRpPAM0QPV2etGCj+dU7xgF9BWnn9mzbGC5iy8EUClyGil/af
k3i/bCxs6IgpQ76LaezJtGPtn1jbohrO4qRqlatUAJCwgCYMCkxkIk+Pr4A3x4c=
=6WvB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci fixes, enhancements
Almost exclusively bugfixes, though in this case,
we are adding functionality to the pxb in order
to make OVMF work on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri Jun 26 14:43:27 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
Fix glib_subprocess test
hw/pci-bridge: format special OFW unit address for PXB host
hw/core: explicit OFW unit address callback for SysBusDeviceClass
hw/pci-bridge: disable SHPC in PXB
hw/pci-bridge: introduce "shpc" property
hw/pci: introduce shpc_present() helper function
hw/pci-bridge: add macro for "msi" property
hw/pci-bridge: add macro for "chassis_nr" property
hw/pci-bridge: expose _test parameter in SHPC_VMSTATE()
migration: introduce VMSTATE_BUFFER_UNSAFE_INFO_TEST()
add pci-bridge-seat
pc: cleanup and convert TMP ACPI device description to AML API
MAINTAINERS: add ACPI entry
vhost: correctly pass error to caller in vhost_dev_enable_notifiers()
balloon: add a feature bit to let Guest OS deflate balloon on oom
qdev: fix OVERFLOW_BEFORE_WIDEN
virito-pci: fix OVERRUN problem
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A typo means that the tests dependent on glib with subprocess
support are never run.
Fixes: 9d41401b90
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is an attempt to rearrange configure --help output a bit
and consolidate pairs of --enable/disable into its own section.
After this, help text is easier to sort, manage and read.
More descriptive text can be added as well, since we now have
more space.
While at it, mention en/dis-able-vte.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The help text says --extra-ldflags is appended to LDFLAGS so make it so.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
New options were added to enable Windows MSI installation package
creation:
Option --enable-guest-agent-msi, like the name suggests, enables building
Windows MSI package for QEMU guest agent; option --disable-guest-agent-msi
disables MSI package creation; by default, no MSI package is created
Signed-off-by: Yossi Hindin <yhindin@redhat.com>
Message-Id: <1430913460-13174-5-git-send-email-yhindin@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DirectSound should be a superior choice on Windows.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ESD is no longer developed and replaced by PulseAudio.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some recent patches require a function from libfdt version 1.4.0,
so we should check for this version during the configure step
already. Unfortunately, there does not seem to be a proper #define
for the version number in the libfdt headers. So alternatively,
we check for the availability of the required function
fdt_get_property_by_offset() instead instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
It makes sense that extra-cflags should be appended after the normal
CFLAGS so they don't get overridden by default behaviour. This way if
you specify something like:
./configure --extra-cflags="-O0"
You will see the requested behaviour.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
libepoxy does the opengl extension handling for us.
It also is helpful for trouble-shooting as it prints nice error messages
instead of silently failing or segfaulting in case we do something
wrong, like using gl commands not supported by the current context.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
gdb allows registers to be displayed/modified, and is being updated
to account for the new vector registers. Mirror these changes in
the gdb stub in qemu so that this can be performed when gdb is
attached to the qemu gdbserver.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This provides g_ptr_array_new_with_free_func, as well as a few
other functions that we've been hacking around in glib-compat.h.
Cleaning up the compatibility headers will come later.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1431469140-22208-2-git-send-email-jsnow@redhat.com
Test if ccache is interfering with semantic analysis of macros,
disable its habit of trying to compile already pre-processed
versions of code if so. ccache attempts to save time by compiling
pre-processed versions of code, but this disturbs clang's static
analysis enough to produce false positives.
ccache allows us to disable this feature, opting instead to
compile the original version instead of its preprocessed version.
This makes ccache much slower for cache misses, but at least it
becomes usable with QEMU/clang.
This workaround only activates for users using ccache AND clang,
and only if their configuration is observed to be producing warnings.
You may need to clear your ccache for builds started without -Werror,
as those may continue to produce warnings from the cache.
Thanks to Peter Eisentraut for his writeup on the issue:
http://peter.eisentraut.org/blog/2014/12/01/ccache-and-clang-part-3/
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427324259-1481-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The glib headers use GCC attributes. Unfortunately the __GNUC__ and
__GNUC_MINOR__ version macros are also defined by clang, but clang
doesn't support the same attributes as GCC.
clang 3.5.0 does not support the __alloc_size__ attribute:
c047507a9a
The following warning is produced:
gstrfuncs.h:257:44: warning: unknown attribute '__alloc_size__' ignored [-Wunknown-attributes]
G_GNUC_MALLOC G_GNUC_ALLOC_SIZE(2);
gmacros.h:67:45: note: expanded from macro 'G_GNUC_ALLOC_SIZE'
#define G_GNUC_ALLOC_SIZE(x) __attribute__((__alloc_size__(x)))
This patch checks whether glib headers cause warnings and disables
-Wunknown-attributes if it is able to.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427324259-1481-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Factor out the function that checks if a compiler
flag is supported or not.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427324259-1481-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
gcc 4.9.2 treats -nopie as an error:
cc: error: unrecognized command line option ‘-nopie’
clang 3.5.0 treats -nopie as a warning:
clang: warning: argument unused during compilation: '-nopie'
The causes ./configure to fail with clang:
ERROR: configure test passed without -Werror but failed with -Werror.
Make the -nopie test use -Werror so that compile_prog works for both gcc
and clang.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427324259-1481-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
- two improvements to "info mtere" from Gerd
- KVM support for memory transaction attributes
- one more small step towards unlocked MMIO dispatch
- one piece of the qemu-nbd errno fixes
- trivial-ish patches from Denis and Thomas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVTLBhAAoJEL/70l94x66DkGIH/jlNJBMBGhlH/lwb1LzxtAMX
OxyDxsiwJpSxsOiZiY3oRz7d6VV6TCrmx5L+1HgG5IzU3WC61Tq6/FK4EXLepZIH
GSYlLtAALWny+2Uwsyh1Z7MMr5yxyhgeORk/l7O8pncmMeysludbEaJqQg8Aa9A2
j0B2pv4tvcl/qhuIFXL1YlbYMVXMsZy5W65D8jq+B6qf3q8kUcdKvgvbUMrxAiSH
JMISo4Z32t9w8SGnhlBa9s4HfN2yOvULRAozzkDBAu4c41cZrw16lvTV8XotamnU
LrG6eQ+2PFeIrcGhuIu7z5Bi4yiRRiThfRLCAvVApVTQYUf7IwvPNa5K1FrP9YU=
=Z/UD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- build bugfix from Fam and new configure check from Emilio
- two improvements to "info mtere" from Gerd
- KVM support for memory transaction attributes
- one more small step towards unlocked MMIO dispatch
- one piece of the qemu-nbd errno fixes
- trivial-ish patches from Denis and Thomas
# gpg: Signature made Fri May 8 13:47:29 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
qemu-nbd: only send a limited number of errno codes on the wire
rules.mak: Force CFLAGS for all objects in DSO
configure: require __thread support
exec: move rcu_read_lock/unlock to address_space_translate callers
kvm: add support for memory transaction attributes
mtree: also print disabled regions
mtree: tag & indent a bit better
apic_common: improve readability of apic_reset_common
kvm: Silence warning from valgrind
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The codebase doesn't build without __thread support.
Formalise this requirement by adding a check for it in the
configure script.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
tricore was out of alphabetical order in the target list. Fix.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This adds "--enable-tcmalloc" and "--disable-tcmalloc" to allow linking
to libtcmalloc from gperftools.
tcmalloc is a malloc implementation that works well with threads and is
fast, so it is good for performance.
It is disabled by default, because the MALLOC_PERTURB_ flag we use in
tests doesn't work with tcmalloc. However we can enable tcmalloc
specific heap checker and profilers later.
An IOPS gain can be observed with virtio-blk-dataplane, other parts of
QEMU will directly benefit from it as well:
==========================================================
glibc malloc
----------------------------------------------------------
rw bs iodepth bw iops latency
read 4k 1 150 38511 24
----------------------------------------------------------
==========================================================
tcmalloc
----------------------------------------------------------
rw bs iodepth bw iops latency
read 4k 1 156 39969 23
----------------------------------------------------------
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1427338992-27057-1-git-send-email-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unfortunately it turns out that libseccomp 2.2 still does not work
correctly on non-x86 architectures; return to the previous configure
setup of insisting on libseccomp 2.1 or better and i386/x86_64 and
disabling seccomp support in all other situations.
This reverts the two commits:
* "seccomp: libseccomp version varying according to arch"
(commit 896848f0d3)
* "seccomp: update libseccomp version and remove arch restriction"
(commit 8e27fc2004)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1428670681-23032-1-git-send-email-peter.maydell@linaro.org
libxseg has changed license to GPLv3. QEMU includes GPL "v2 only" code
which is not compatible with GPLv3. This means the resulting binaries
may not be redistributable!
Disable Archipelago (libxseg) by default to prevent accidental license
violations. Also warn if linking against libxseg is enabled to remind
the user.
Note that this commit does not constitute any advice about software
licensing. If you have doubts you should consult a lawyer.
Cc: Chrysostomos Nanakos <cnanakos@grnet.gr>
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1428587538-8765-1-git-send-email-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Libseccomp dependency was mandating version 2.2.0 on all architectures
and this was causing configure and virt-test to break on non-updates
distros. This patch works-around it and give a more flexible way to
check the version, giving more time for other distros to update
libseccomp version.
Signed-off-by: Eduardo Otubo <eduardo.otubo@profitbricks.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Juan Quintela <quintela@redhat.com>
Message-id: 1427385385-30571-1-git-send-email-eduardo.otubo@profitbricks.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Libseccomp version updated to 2.2.0 and arch restriction to x86/x86_64
is now removed. It's supposed to work on armv7l as well.
Related bug: https://bugs.launchpad.net/qemu/+bug/1363641
Signed-off-by: Eduardo Otubo <eduardo.otubo@profitbricks.com>
Here's a trivial change to enable kvm on x32 architecture.
I'm not 100% sure the result works correctly in all cases,
but this is a good start and in theory everything should
work.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Re-add the glx compile test to configure. We can't use pkg-config to
probe for glx, and as long as milkymist-tmu2 privately uses glx (due to
opengl infrastructure in qemu not being ready yet) we must continue to
test for glx to avoid build failures.
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Rename config option from "glx" to "opengl", glx will not be the only
option for opengl in near future. Also switch over to pkg-config for
opengl support detection.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This patch adds support for bzip2-compressed block entries as introduced
with OS X 10.4 (source: https://en.wikipedia.org/wiki/Apple_Disk_Image).
It was tested against a 5.2G "OS X Yosemite" installation image which
stores the BLXX block in the XML property list (instead of resource
forks) and has over 5k chunks.
New configure entries are added (--enable-bzip2 / --disable-bzip2) to
control inclusion of bzip2 functionality (which requires linking against
libbz2). The help message suggests that this option is needed for DMG
files, but the tests are generic enough that other parts of QEMU can use
bzip2 if needed.
The identifiers are based on http://newosxbook.com/DMG.html.
The decompression routines are based on the zlib case, but as there is
no way to reset the decompression state (unlike zlib), memory is
allocated and deallocated for every decompression. This should not be
problematic as the decompression takes most of the time and as blocks
are typically about/over 1 MiB in size, only one allocation is done
every 2000 sectors.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1420566495-13284-12-git-send-email-peter@lekensteyn.nl
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This efficiently writes zeroes on Linux if the kernel is capable enough.
FALLOC_FL_ZERO_RANGE correctly handles all cases, including and not
including file expansion.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Peter Lieven <pl@kamp.de>
CC: Fam Zheng <famz@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
rules.mak has a rule for .S files using CPP. This will result in
errors like
CPP s390-ccw/start.asm
cc: error: unrecognized command line option '-Wbitwise'
Lets also redefine CPP in case of --enable-sparse.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ioreq-server API added to Xen 4.5 offers better security than
the existing Xen/QEMU interface because the shared pages that are
used to pass emulation request/results back and forth are removed
from the guest's memory space before any requests are serviced.
This prevents the guest from mapping these pages (they are in a
well known location) and attempting to attack QEMU by synthesizing
its own request structures. Hence, this patch modifies configure
to detect whether the API is available, and adds the necessary
code to use the API if it is.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Using "has" is more slick because which(1) is not always there.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Current stable version of libseccomp (2.1.1) only supports i386 and
x86_64 archs correctly. This patch limits the usage of the syscall
filter for those archs and updates to the correct last version of
libseccomp.
This patch also fixes the bug:
https://bugs.launchpad.net/qemu/+bug/1363641
Signed-off-by: Eduardo Otubo <eduardo.otubo@profitbricks.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Moore <pmoore@redhat.com>
c++ compiler isn't wrapped with cgcc, resulting in gcc complaining about
the sparse compiler flags which it doesn't know in case qemu is built
with --enable-sparse.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Other packages may provide includes for pixman as well if the host has a
devel package installed. So add ours to the front to unsure that the
right version is used.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The qemu-aarch64 and qemu-system-aarch64 binaries include support
for all the 32 bit ARM CPUs as well as the 64 bit ones. This means
we need to build in the GDB XML files for the 32 bit CPUs too.
Otherwise gdb will complain:
warning: while parsing target description (at line 1): Could not load XML document "arm-core.xml"
when you try to connect to our gdbserver to debug a 32 bit CPU
running in a qemu-aarch64 or qemu-system-aarch64 binary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410533739-13836-1-git-send-email-peter.maydell@linaro.org
Check for the presence of posix_fallocate() in configure and only
compile in support for PREALLOC_MODE_FALLOC when it's there.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvmclock fix. This was reverted last minute for 2.1, but it is now back
with the problematic case fixed.
Note: I will soon switch to a subkey for signing purposes. To verify
future signed pull requests from me, please update my key with
"gpg --recv-keys 9B4D86F2". You should see 3 new subkeys---the
one for signing will be a 2048-bit RSA key, 4E6B09D7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nP/e
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Usual mix of patches, the most important being Alex and Marcelo's
kvmclock fix. This was reverted last minute for 2.1, but it is now back
with the problematic case fixed.
Note: I will soon switch to a subkey for signing purposes. To verify
future signed pull requests from me, please update my key with
"gpg --recv-keys 9B4D86F2". You should see 3 new subkeys---the
one for signing will be a 2048-bit RSA key, 4E6B09D7.
# gpg: Signature made Fri 26 Sep 2014 15:34:44 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: aka "Paolo Bonzini <bonzini@gnu.org>"
* remotes/bonzini/tags/for-upstream:
kvm/valgrind: don't mark memory as initialized
po: fix conflict with %.mo rule in rules.mak
kvmvapic: fix migration when VM paused and when not running Windows
serial: check if backed by a physical serial port at realize time
serial: reset state at startup
target-i386: update fp status fix
hw/dma/i8257: Silence phony error message
kvmclock: Ensure time in migration never goes backward
kvmclock: Ensure proper env->tsc value for kvmclock_current_nsec calculation
Introduce cpu_clean_all_dirty
pit: fix pit interrupt can't inject into vm after migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
since commit 7dda5dc82a ("migration: initialize RAM to zero") the
guest memory is defined zero. No need to call valgrind on guest memory.
This reverts commit 62fe83318d ("qemu: Use valgrind annotations to
mark kvm guest memory as defined") thus speeding up kvm start if
<includedir>/valgrind/valgrind.h is available.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dataplane doesn't depend on linux-aio any more, so we don't need the
compiling condition now.
Configure options are kept but just print a message.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1410329871-28885-4-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make them consistent with the others.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit c261d774fb added one more binutils
tool: nm also needs a cross prefix.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1411070108-8954-1-git-send-email-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A bunch of bugfixes - some of these will make sense for 2.1.2
I put Cc: qemu-stable included where appropriate.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUGyniAAoJECgfDbjSjVRpxg0H/j4jSEWHm/4uKSly6W4MXxhN
LghE5iAaO3awU88RiRPW/m/g6sagD9RuQAHteHkvyZ6py/li0IFvLtl66OczeSgc
rnM2n9MeYfi5Q05T+ygjqYY2ynosYhrI4iPmsnKqbqLi+WWwQHFKuYKNcNmQjmJu
Sg4KDz+W4p5j/pMUZdgf4lse3PaLXoMy4IA1HC8U1WmwvyNLZrPRTXhFn1hFbxU6
Rf604wz6gkAFvwizt2SoRMOIF4w0meCKemY1wqcwOeDWqP6Bj76RnRCrVR06AgnX
ngVsrP5SrWymqwFUP9ZpeNdBOQSxXE3zT1cE6JU3/KUvTBs6Eur4Dnz7g2mPb8I=
=nHHz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio, misc bugfixes
A bunch of bugfixes - some of these will make sense for 2.1.2
I put Cc: qemu-stable included where appropriate.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 18 Sep 2014 19:52:18 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
pc: leave more space for BIOS allocations
virtio-pci: fix migration for pci bus master
vhost-user: fix VIRTIO_NET_F_MRG_RXBUF negotiation
virtio-pci: enable bus master for old guests
Revert "virtio: don't call device on !vm_running"
virtio-net: drop assert on vm stop
Revert "rng-egd: remove redundant free"
qdev: Move global validation to a single function
qdev: Rename qdev_prop_check_global() to qdev_prop_check_globals()
test-qdev-global-props: Test handling of hotpluggable and non-device types
test-qdev-global-props: Initialize not_used=true for all props
test-qdev-global-props: Run tests on subprocess
tests: disable global props test for old glib
test-qdev-global-props: Trivial comment fix
hw/machine: Free old values of string properties
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
follow-up patch moves global property tests to subprocesses.
Unfortunately with old glib this causes:
tests/test-qdev-global-props.c: In function
‘test_static_prop’:
tests/test-qdev-global-props.c:80:5: error: implicit
declaration of function ‘g_test_trap_subprocess’
[-Werror=implicit-function-declaration]
tests/test-qdev-global-props.c:80:5: error: nested extern
declaration of ‘g_test_trap_subprocess’ [-Werror=nested-externs]
This function was only added in glib 2.38, and our
minimum version is 2.12.
To fix, disable the test for glib < 2.38.
Apply before that patch to avoid breaking bisect.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit a93a3af9 introduces use of PIXMAN_TYPE_RGBA, but it's only available
in pixman >= 0.21.8. If pixman doesn't meet the version requirement, qemu
will fail to build with following message:
qemu/ui/qemu-pixman.c: In function ‘qemu_pixelformat_from_pixman’:
qemu/ui/qemu-pixman.c:42: error: ‘PIXMAN_TYPE_RGBA’ undeclared (first use in this function)
qemu/ui/qemu-pixman.c:42: error: (Each undeclared identifier is reported only once
qemu/ui/qemu-pixman.c:42: error: for each function it appears in.)
This patch fixes the problem by checking the pixman version.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add tcg and cpu model initialization.
Add gen_intermediate_code function.
Activate target in configure and add softmmu config.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-id: 1409572800-4116-5-git-send-email-kbastian@mail.uni-paderborn.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the relevant s390x feature xml files taken from gdb.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
commit 7537fe04 QMP: QMP/ -> docs/qmp/
Above commit has moved last QMP files to docs/qmp and it's not necessary
to create QMP directory. So remove it from configure.
Signed-off-by: Liming Wang <liming.wang@canonical.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add support for the setns and unshare syscalls, trivially passed through to
the host. Based on patches by Paul Burton, added configure check.
Signed-off-by: Paul Burton <paul@archlinuxmips.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Adds support for the timerfd_create, timerfd_gettime & timerfd_settime
syscalls, allowing use of timerfds by target programs.
v2: By Riku - added configure check for timerfd and ifdefs
for benefit of old distributions like RHEL5.
Signed-off-by: Paul Burton <paul@archlinuxmips.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5w3j
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches
# gpg: Signature made Fri 15 Aug 2014 14:07:42 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (59 commits)
block: Catch !bs->drv in bdrv_check()
iotests: Add test for image header overlap
qcow2: Catch !*host_offset for data allocation
qcow2: Return useful error code in refcount_init()
mirror: Handle failure for potentially large allocations
vpc: Handle failure for potentially large allocations
vmdk: Handle failure for potentially large allocations
vhdx: Handle failure for potentially large allocations
vdi: Handle failure for potentially large allocations
rbd: Handle failure for potentially large allocations
raw-win32: Handle failure for potentially large allocations
raw-posix: Handle failure for potentially large allocations
qed: Handle failure for potentially large allocations
qcow2: Handle failure for potentially large allocations
qcow1: Handle failure for potentially large allocations
parallels: Handle failure for potentially large allocations
nfs: Handle failure for potentially large allocations
iscsi: Handle failure for potentially large allocations
dmg: Handle failure for potentially large allocations
curl: Handle failure for potentially large allocations
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VM Image on Archipelago volume is specified like this:
file.driver=archipelago,file.volume=<volumename>[,file.mport=<mapperd_port>[,
file.vport=<vlmcd_port>][,file.segment=<segment_name>]]
'archipelago' is the protocol.
'mport' is the port number on which mapperd is listening. This is optional
and if not specified, QEMU will make Archipelago to use the default port.
'vport' is the port number on which vlmcd is listening. This is optional
and if not specified, QEMU will make Archipelago to use the default port.
'segment' is the name of the shared memory segment Archipelago stack is using.
This is optional and if not specified, QEMU will make Archipelago to use the
default value, 'archipelago'.
Examples:
file.driver=archipelago,file.volume=my_vm_volume
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123,
file.vport=1234
file.driver=archipelago,file.volume=my_vm_volume,file.mport=123,
file.vport=1234,file.segment=my_segment
Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some non-linux systems, for example a system with
FreeBSD kernel and glibc, may declare struct mmsghdr
(in glibc) but may not have linux-specific header
file linux/ip.h. The actual implementation in qemu
includes this linux-specific header file unconditionally,
so compilation fails if it is not present. Include
this header in the configure test too.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If --enable-stack-protector is used is used, configure script try to use
--fstack-protector-strong. In case it's not supported, --fstack-protector-all
is enabled. If both protectors are not supported, configure does not use
any protector at all without any notification.
This patch reports error when user requests stack protector to be used and
both protector modes are not supported. Behavior is not changed in case
user do not use any of --enable-stack-protector/--disable-stack-protector.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
[Fix non-POSIX operator in test. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The mmsghdr struct is only introduced in Linux 2.6.32; add a
configure check for it and disable L2TPV3 on hosts which are
too old to provide it, rather than simply failing to compile.
Reported-by: chenliang <chenliang88@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1404219488-11196-1-git-send-email-arei.gonglei@huawei.com
[PMM: cleaned up commit message and corrected kernel version number]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The existing test whether "-lm" needs to be included or not is
insufficient as it reports false negative on Fedora20/ppc64.
This happens because sin(0.0) is a constant value which compiler
can safely throw away and therefore there is no need to add "-lm".
As the result, qemu-nbd/qemu-io/qemu-img tools cannot compile.
This adds a global variable and uses it in the test to prevent
from optimization.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[Use Peter's improvement on the test to fool LTO, and remove the
now useless -lm addition in Makefile.target. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to allow out-of-tree iotests, create a symlink for the check
script in the build tree.
While doing so, also write configured options relevant to the iotests to
common.env in the build tree; currently, this is the command to invoke
Python 2.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I don't see why tpm is disabled by default: it doesn't have any
external dependencies, or change default behavior. Leaving it disabled
is just going to cause it to bit rot.
Enable it by default, and add a --disable-tpm option.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The other tcg backends that support 32- and 64-bit modes
use the 32-bit name for the port. Follow suit.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
* remotes/kvm/uq/master:
hw/mips: malta: Don't boot from flash with KVM T&E
MAINTAINERS: Add entry for MIPS KVM
target-mips: Enable KVM support in build system
hw/mips: malta: Add KVM support
hw/mips: In KVM mode, inject IRQ2 (I/O) interrupts via ioctls
target-mips: Call kvm_mips_reset_vcpu() from mips_cpu_reset()
target-mips: kvm: Add main KVM support for MIPS
kvm: Allow arch to set sigmask length
target-mips: get_physical_address: Add KVM awareness
target-mips: get_physical_address: Add defines for segment bases
hw/mips: Add API to convert KVM guest KSEG0 <-> GPA
hw/mips/cputimer: Don't start periodic timer in KVM mode
target-mips: Reset CPU timer consistently
KVM: Fix GSI number space limit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
numa work by Hu Tao and others
memory hotplug by Igor
vhost-user by Nikolay, Antonios and others
guest virtio announcements by Jason
qtest fixes by Sergey
qdev hotplug fixes by Paolo
misc other fixes mostly by myself
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTowW+AAoJECgfDbjSjVRpnMMH/jp3sKGzJumYLbi5ihjmYyND
jYd6ySXoVAjUTgaCvdje5srisOap8pbc783kQvQS4CeWsjZ5Vvh+PZjkBPIqF1pD
celxGQ43CY7QSUWq+02Dg9VIUwLwZqdKlxNsV01FligQn+ZBQ6sQ6ksWx7oGzqRt
5/HMZykbwUvSk/4xGUaMn2+/4uhQ0Wz5EsCkv9L/u8kS72k6ldc/tCGZMzBUNHTM
rW5FPYwMQP0MXgGTXnlLEQjJ7Lozc66IaMZoHw/a/aGSIxdag9Otj0ADuXq6yZaV
Xi4O/EOJWd1JpSG7w8LOyIZNakpHkU43fmJCLzBjDAupHeRp57TcW5ox4PJYAtg=
=Oxdt
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio,hotplug fixes, enhancements
numa work by Hu Tao and others
memory hotplug by Igor
vhost-user by Nikolay, Antonios and others
guest virtio announcements by Jason
qtest fixes by Sergey
qdev hotplug fixes by Paolo
misc other fixes mostly by myself
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mst/tags/for_upstream: (109 commits)
numa: use RAM_ADDR_FMT with ram_addr_t
qapi/string-output-visitor: fix bugs
tests: simplify code
qapi: fix input visitor bugs
acpi: rephrase comment
qmp: add ACPI_DEVICE_OST event handling
qmp: add query-acpi-ospm-status command
acpi: implement ospm_status() method for PIIX4/ICH9_LPC devices
acpi: introduce TYPE_ACPI_DEVICE_IF interface
qmp: add query-memory-devices command
numa: handle mmaped memory allocation failure correctly
pc: acpi: do not hardcode preprocessor
qmp: clean out whitespace
qdev: recursively unrealize devices when unrealizing bus
qdev: reorganize error reporting in bus_set_realized
qapi: fix build on glib < 2.28
qapi: make string output visitor parse int list
qapi: make string input visitor parse int list
tests: fix memory leak in test of string input visitor
hmp: add info memdev
...
Conflicts:
include/hw/i386/pc.h
[PMM: fixed minor conflict in pc.h]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add detection of libnuma (mostly contained in the numactl package)
to the configure script. Can be enabled or disabled on the command
line, default is use if available.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The supplied chardev id will be inspected for supported options. Only
a socket backend, with a set path (i.e. a Unix socket) and optionally
the server parameter set, will be allowed. Other options (nowait, telnet)
will make the chardev unusable and the netdev will not be initialised.
Additional checks for validity:
- requires `-numa node,memdev=..`
- requires `-device virtio-net-*`
The `vhostforce` option is used to force vhost-net when we deal with
non-MSIX guests.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This patch lifts the minimum supported libiscsi version from 1.4.0 to
1.9.0 since the BUSY patch required that change.
On one this allows us to remove all #ifdefs from the code which
makes the code easier to maintain and read. On the other hand
I would not recommend libiscsi prior to 1.8.0 for production use
because the following important libiscsi fixes for deadlocks and
protocol errors are missing prior to 1.8.0:
dbe9a1e SOCKET queue cmd PDUs directly in waitpdu queue
30df192 DATA-OUT set pdu->cmdsn appropriately
548bd22 ISCSI fix broken send logic in iscsi_scsi_async_command
14bee10 RECONNECT do not increase CmdSN for immediate PDUs
1f4a66a PDU queue out PDUs in order of itt.
562dd46 PDU avoid incrementing itt to 0xffffffff
cd09c0f PDU use serial32 arithmetic for cmdsn, maxcmdsn and expcmdsn.
89e918e SOCKET validate data_size in in_pdu header
91267f5 Limit immediate and unsolicited data to FirstBurstLength
Note that libiscsi 1.9.0 was released on Feb 24th, 2013, about
one month after 1.8.0.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable KVM support for MIPS in the build system.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
